YEid 01

4a

Installationlniiitionsand

Use&CareGuide

Air discharge

Control panel

Model and serial number plate

(not shown)

Control panel

Model and serial number

plate

AIRCONDITIONERS

ModelsACS602XT ACS802XV ACSl02XT ACC602XT

a-s3

Contents

Thank you for buying a Whirlpool appliance. Please complete and mail the Owner Registration Card provided with this prod- uct. Then complete the form below. Have this information ready if you need service or call with a question.

l Copy model and serial numbers from plate (see diagram on page 12) and purchase date from sales slip.

lKeep this book and sales slip together in a handy place.

Model Number

Serial Number

Purchase Date

Servlce Company Phone Number

It is your personal responsibility to be sure your air conditioner:

l Has been properly installed.

l Is the right size for the area you want to cool.

l Is properly connected and grounded to electrical supply.

l Is used only for the job it was intended to do.

lIs not used by children or anyone unable to operate it properly.

l Is properly maintained.

l Also, remove energy label and buy guide. Use damp cloth to take off any glue residue. Do not use a sharp instrument or any harsh or abrasive cleaners.

Important:

Please read this Use & Care Guide before install- ing or using your air conditioner. It tells you how to install and operate it, and gives important electrical information. Save it for future use in case you have a question or move the air conditioner.

Personal Injury Hazard

The metal fins on the coils are sharp. Han- dle the air conditioner with care. Failure to do so could result in personal injury.

2

ElectricalRequirements

Electrical requirements are different for the two models pictured on the cover, depending on the ampere rating of your unit. The number of amperes is printed on the serial plate, which is attached to the front of the unit behind the front panel (see diagram on page 12).

Observe all local governing codes and ordinances.

Do not, under any circumstances, remove the power supply cord grounding prong.

Receptaclewiring

Receptacle wiring should be a minimum of 14 gauge. Use copper wire only. It is the personal responsibility of the consumer to provide proper and adequate receptacle wiring installed by a qualified electrician. Observe National Electrical Code and all local governing codes and ordinances.

Z&prong

Electricalrequirements

Electrical Shock Hazard

l Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. Do not modify the power supply cord plug - if it will not fit the outlet, have a proper outlet installed

by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electrical shock.

l Do not use an extension cord with this appliance. Such use may result in a fire, electrical shock or other personal injury.

. Do not have a fuse in the neutral or grounding circuit. This could result in a

risk of electrical shock.

A 115 volt, 60 Hz AC only, 15 ampere fused elec- trical supply is required (time delay fuse or time delay circuit breaker required). It is recommended that a separate circuit, serving only this appliance, be provided for models with serial plate amperes up through 7.5. A separate circuit is required

for models with serial plate amperes of 7.6 through 12.0.

Electricalconnection

Electrical ground is required on this appliance.

Recommended grounding method

For your personal safety, this appliance must be grounded. This air conditioner is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall receptacle, grounded in accordance with the National Electrical Code, ANSVNFPA 70-1987 (or to the latest), and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded 3-prong wall receptacle

installed by a qualified electrician.

3

Grounding prong

Temporary grounding method

If changing and properly grounding the wall recep- tacle is impossible and where local codes permit (consult your electrical inspector), a temporary adapter may be plugged into the existing 2-prong wall receptacle to male with the 3-prong power supply cord. This, however, is not recommended.

If this is done, however, you must connect the grounded eyelet on the adapter to the wall recep- tacle cover plate screw and from this same screw, you must connect a separate copper ground wire (#14 minimum) to a grounded cold water pipe.

???Do not ground to a gas supply pipe. Do not connect to electrical supply until appliance is grounded. Do not, under any circumslances, remove the power supply cord grounding prong. *Cold water pipe must have metal continuity to electrical ground and not be interrupted by plas- tic, rubber or other electrically insulating connec- tors (including water meter or pump) without adding a jumper wire at these connections.

InstallationInstructions

If you have one of these models: ACS602XT

ACS802XV

ACS102XT,

follow ???Installation instructlons 1??? below.

If you have model ACC602XT, follow ???lnstalla- tion instrucGons 2??? on page 8.

Installationinstructions1

To help avoid any installation problems and to help ???assure trouble-free performance of your new air conditioner, read these installation instructions, as well as the operating instructions and electrical requirements before installing your unit.

Also, inspect thecondition of the window where the air conditioner will be installed. Be sure it will support the weight of the unit.

Personal Injury Hazard

l Because this air conditioner weighs about 90 to 105 pounds, it is recommended that you have someone help you install your new unit and that you both use proper lift- ing techniques.

l This appliance must be installed according to all applicable codes and ordinances.

l Handle the air conditioner with care. The metal fins on the front and rear coils are sharp.

. Do not use the collected water for drinking purposes. It is not sanitary.

l Be sure air conditioner does not fall out of window during or after installation.

Failure to follow the above precautions could result in personal injury.

1. Unpack mounting parts before installing your air conditioner. Make sure you have all the necessary parts. A normal installation can be made with a screwdriver, saw, small level, pocket knife, tape measure, drill and W: 9/64??? and %6???

drill bits.

5Translucent panel (1)

6Screw-10x1???(2)

6A screw - 10 x 13/4??? (2)

7Screw - 8 x 34??? (5)

8Side seal strip (1)

9Lower track seal (1)

10Locking bracket (1)

11Foam seal strip (1)

12Panel frame (1)

13Thread cutting screw #% x %??? (4)

If using Item 13 for fastening Item 10 or 12 to metal or plastic, use ???h4??? dia. or #28 drill.

2. Pick the right window. First, decide what room(s) you want to cool. Then choose a window that will allow the air-conditioned air to flow freely and directly into the room(s) you want cooled. Remember, it???s difficult to move air around corners. If the inner sliding window slides to the left, the unit will be installed on the right. Remove window screen if there is one. Choose a sliding window that???s also near an electrical outlet. (Refer to ???Electrical Requirements??? on page 3 for type of receptacle and wiring needed.) Do not use an extension cord.

The sliding window in which you place your air conditioner should have an opening of at least 15%??? wide and 21%??? to 40%??? high (see diagram). For installations up to 62%??? high, a special kit (Part No. 977449) is available. For windows as low as 207/re???: you must install without filler frame and remove top angle on unit, reinstalling 3 screws into top of cabinet.

This model may also be installed in steel hinged casement windows. The steel hinged casement window mUSt have an opening at least 15%??? wide and no more than 16%??? wide.

3. Place shelf In wlndow with tabs down against the track surface.

Installation Instructions

Continued

Room side

4. Attach support bracket (Item 2) loosely to the underside of shelf with either short or long leg down and with end of bracket either toward or away from window, depending upon construction and depth of wall and window sill (see diagram). Attach sill bracket (Item 3). Each bracket is attached using one %6??? bolt, nut and washers (Items 4,4A, 48 and 4C).

9. Measure out the distance determined in Step 8 and mark it along the 20%??? side of translu- cent panel. Clamp panel between a board and an appropriate supporting surface close to the mark and cut with fine tooth saw. Remove burrs.

10. Lift vertically removing panel frame from unit. Slide translucent panel into groove in frame, keeping honeycomb side to the face side of frame (see diagram). Slide frame back into place on unit. Panel should enter the top angle groove.

6

Butt to bottom

of flller frame. cut off axcess

length below unlt.

Seal strip

11. Peel backing from seal strip (Item 8) and press it onto side filler frame guides on each side of unit.

12. Place unit in wlndow by resting unit on shelf. Push unit toward window so side angles are sealing against the side jamb stop (see diagram). Slide the opened window sash firmly to make cer- tain the frame and unit sealing strips are sealing.

13. Using Ye??? drill, install locking screws (Item 7). Use two screws in top jamb and in the side bottom flanges. If you need additional holding strength, add two more screws at upper sides of filler frame (marked ???A???). Also, two screws can be added at unit sides (marked ???B???). However, if yqu add screws at ???B:???you must use a %6??? drill bit to predrill through the plastic sides of air conditioner.

14. Lock the sllding sash at bottom using lock bracket (Item 10) and screw (Item 7) as shown in diagram at left. Use a ???/a??? drill bit to drill through track before inserting screw.

15. Cut seal strip (Item 11) to length. Install it between space of opened sash and glass of the closed sash (see diagram).

Installation Instructions

Continued

Shelf -

Seal, item 9

Use screws, item 6 or 6A

Tab on - shelf

16. For installation In windows having no slde flanges or with wood stops.

The flanges (top and two sides) on the air condi- tioner must mate against companion flanges on the window, not more than 1/16??? (.2 cm) in thickness. On the side with the opened sash, the leading edge of the sash becomes the flange. On the top and jamb side of most metal windows, the flange is there.

In windows where there are no flanges or where there are thick wood flanges or stops, use metal angles or wood to provide a stop for the unit flange. Diagrams at left show three suggested methods.

17. For installation in steel casement windows.

Follow Steps 2 and 3 on page 5. NOTE: In Step 3, the shelf labs must butt to the front of the bottom angle on the casement (see diagram

at leff).

When Step 3 is finished, follow Steps 4 through 10 on page 6, and Steps 11 and 12 on page 7. Then proceed with the final two para- graphs in this Step 17, which immediately follow.

Open window at least 16O???to allow room for unit cabinet. If necessary, remove window crank handle so the window will open wide enough and not interfere with shelf against the bottom sill angle. Tie opened window to the wall or frame to prevent the window from swinging.

Drill V?????? holes in the window jamb top to line up with holes in filler frame (see diagram at left). Use two thread cutting screws (Item 13) to secure unit. If you need additional holding strength, add screws at the bottom of the unit side channels (see Step 13 diagram).

Installationinstructions2

To help avoid any installation problems and to help assure trouble-free performance of your new air conditioner, read these installation instructions, as well as the operating instructions and electrical requirements before installing your unit.

Inspect the condition of the window where

the air conditioner will be installed. Be sure it will support the weight of the unit.

Personal Injury Hazard

Be sure air conditioner does not fall out of,

window during installation. Personal injury

or damage could result.

8

Installation Instructions

Continued

5. Check the knurled knob screws to see that the top mounting brackets (Item 5) are retracted to the center of the unit. They must not interfere with the window frame when the unit is installed.

6. Lift the unit into the window opening and slide it back until the mounting frame comes into contact with the window frame.

conditioner

%??? Max. -I I-

Back of air conditioner

outslde of wlndow

Sheet metal screw ???S -

7. Replace the bottom mounting brackets (Item 3) by hooking the bracket over the window frame. Replace the top screws (Item 1) in the mounting bracket, leaving them loose enough so there is about %6??? of play. Tighten the bottom screws (Item 2). This will pull the unit mounting flange tigh:ly to the window frame, sealing and locking the air conditioner in place.

6. Loosen the two knurled knob screws and slide the top mounting bracket (Item 5) toward the outside of the unit, engaging the window frame.

Tighten the knurled knob screw in this position. This will lock the unit in place so it cannot tilt into the room. The installation is now complete.

mounting brackets provided with the unit, remove brackets and fasten flanges of unit with sheet metal screws. These screws are not included with your air conditioner. The window opening for your installation must not be wider than 15???:

10

Wlndow opening frame -

Knurled

I I knob

Personal Injury Hazard

l Because this air conditioner weighs about 70 to 75 pounds, it is recommended that you have someone help you tnstall your new unit and that you both use proper lift- ing techniques.

l This appliance must be installed according to all applicable codes and ordinances.

l Handle the air conditioner with care. Watch out for the sharp metal fins on the front and rear coils.

l Do not use the collected water for drinking purposes. It is not sanitary.

Failure to follow the above precautions could result in personal injury.

1. Unpack mounting parts before installing your air conditioner. Be sure you have all the nec- essary parts (see top two diagrams at left). This air conditioner will fit most steel casement windows. A normal installation can be made with a screw- driver, %6??? socket driver, tape measure and drill.

Description of parts (top hvo diagrams at left) 1 #lO x W long s.m. screw

2 # 1O-32 x 3/s???long math. screw 3 Bottom mounting bracket

4 Knurled knob screw

5 Top mounting bracket

NOTE: Above parts (not shipped loose) installed on unit by factory.

2. Pick the right window. First, decide what room(s) you want to cool. Then choose a window that will allow the air-conditioned air to flow freely and directly into the room(s) you want cooled. Remember, it???s difficult to move air around corners. Choose a window that???s also near an electrical outlet. (Refer to ???Electrical Bequirements??? on page 3 for type of receptacle and wiring needed.) Do not use an extension cord.

To be able to use the window mounting parts shown in the diagram to the left of Step 1 above, the window should have a minimum width of 14%??? and a maximum width of 16??? (see ???A???in bottom diagram). The window should have a minimum height of 10%??? and a maximum height of 11%??? (see ???B???in bottom diagram).

3.Remove the glass from the frame opening selected. Clear away any hardened putty.

4.Before sliding unit through the casement opening, remove the bottom window bracket

(Item 3) on both sides of the unit. NOTE: Only the top screws (Item 1) need to be removed.

9

OperatingInstructions

Startingyourair conditioner

1. Set exhaust control (if your unit is so equipped) to CLOSED for maximum cooling.

LModels

ACSSOZXT

ACSSO2XV

ACSlO2XT

2. Choose either LO COOL or HI COOL fan speed setting.

Ifyou turn your air conditioner off, wait at least two minutes before turning it back on or you may blow a fuse.

I

Model

ACC602XT

3. mm the thermostat control to number 6 (mid-setting). You can adjust the air conditioner???s cooling performance by resetting the thermostat control to a higher number for maximum cooling.

Lower the number setting for less cooling. You will need to experiment to find the setting which suits you best.

EXHAUST

Fan

Openonly

CLOSED UN17OFF

(J)2:&

OPENLOCOOL

EXHAUST

Fan

Closedonly

Theexhaustcontrol

The exhaust control setting draws stale or smoky air from the room.

1. To exhaust room air

Set exhaust control to OPEN. Adjust fan control

to speed desired. If no cooling is desired, use FAN ONLY setting.

2. To circulate room air

Set exhaust control to CLOSED. Adjust fan control to FAN ONLY

Changingairdirection

The louvers in the grille area at the top of the air conditioner control the direction of the cooled air.

If your unit looks like Figure A, move

the lever at the top of the grille to the right, left or straight ahead. Simply move the lever in the direction you want the air to go. The rear vertical louvers in the grille can be adjusted left, right or straight ahead. The front set is fixed and directed upward.

If your unit looks like Figure B, turn the circular air discharge grilles on top of the unit Both grilles can be adjusted to the right or left, or ad- justed individually.

11

Operating Instructions

Continued

Cleaningandcaringforyour air conditioner

Proper use and care of your air conditioner will help ensure longer life of the unit and lower operat- ing costs. Follow these instructions carefully. Call your Whirlpool servicing dealer for an annual checkup.

Cleaning of front panel

Electrical Shock Hazard

Disconnect from electrical supply before cleaning unit. Failure to do so could result in personal injury.

1. Remove the front panel from unit when clean- ing. Press down at top edge of the front, as shown in diagrams at left (depending on your

2. When the front moves away from top of cabinet, pull top of front toward you.

3. Lift up and away from the bottom spring clips.

serial number

4. Clean front panel with warm water and mild soap or detergent. Use a soft cloth. Rinse and dry. Replace front panel.

5. Wipe control panel clean with a soft dry cloth.

Cleaning air conditioner filter

The filter is cleanable. A clean filter helps remove dust, lint and other particles from the air. Check every two weeks to see if filter needs cleaning.

1. Remove front panel as shown above.

2. Remove filter by releasing it from plastic clips as shown in diagrams at left (depending on your model).

3. Clean filter, using a vacuum cleaner. -OR-

4. If very dirty, wash filter with warm water and mild detergent. Air dry thoroughly before replacing.

Back side of

Annual maintenance for your air conditioner

Your air conditioner needs annual maintenance to help ensure steady, top performance throughout the year.

Call the service company recommended by your dealer to:

lInspect and clean the coils and condensate water passages.

l Check fan and oil the fan motor.

l The compressor is sealed and needs no oiling.

Expense of annual inspection is customer???s responsibility.

-OR-

If you are familiar with electrical appliances, you can do the cleaning and maintenance yourself. If you decide to go ahead, follow these steps:

nals. Failure to follow the above precau- tions could result in personal injury.

1.Disconnect power supply.

2.Remove unit from cabinet. Wrap the motor, electrical control box and electrical terminals box in plastic film and make sure no water or other liquid gets inside any of these parts. It could damage the insulation and cause serious trouble.

3.Carefully clean and hose out the base, coils and condensate pans. Clean at least once a year or more often if the condenser coils and pans col- lect dirt, sand, leaves, insects or algae. Also, clean if you detect an odor from the air condi- tioner. While the cabinet is open, this is a good time to oil the fan motor.

4.Remove plastic film from motor and electrical parts.

5.Replace unit in cabinet.

6.Reconnect power supply.

NOTE: It is a good idea to wail 24 hours before starting the unit again. This allows time for all areas to dry out. The water from rainfall or from normal operation does not harm these components.

Personal Injury Hazard

l Because your air conditioner weighs from 70 to 105 pounds, it is recommended that you have someone help you wtien you remove and reinstall your unit and that you both use proper lifting techniques.

l Handle the air conditioner with care. Watch out for the sharp metal fins on the front and rear coils.

l Do not use the collected water for drinking purposes. It is not sanitary.

Failure to follow the above precautions could result in personal Injury.

13

Operating Instructions

Continued

Oiling the fan motor

Electrical Shock Hazard

Disconnect power cord from receptacle before oiling motor. Failure to do so could result in personal injury.

1. Oil the fan motor per instructions on the motor. To add oil, pull out the oil hole plug at each end of the motor (see diagram). An easy-to-use one-ounce capsule of especially recommended oil (Part No. 10943) can be ordered from your Whirlpool servicing dealer, or use SAE #20 non-detergent oil.

2. Replace the plug to keep dirt from motor bearings.

3. Reinstall the unit in cabinet after performing maintenance. Refer to the ???lnslallation instruc- tions??? section for your unit.

Energy saving tips

l

l

l

l

l

l

l

Improve home insulation (seal doors, windows, and close fireplace flue).

Close blinds or drapes on sunny side of house; add window awnings.

Keep air filter clean. Don???t block air flow with drapes or furniture.

Ventilate attic (high temperature levels add to normal cooling load).

Try not to use heal producing appliances during the hottest part of the day. Turn lights, radios, televisions, and other appliances off when not needed.

Keep heat registers and cool air returns closed or blocked off so cooled air won???t escape.

Use a vent fan in areas where cooking, laundry, or bathing is done to pull out extra heat and moisture near its source.

14

IfYouNeedServiceOrAssistance

Wesuggestyoufollow thesefivesteps:

1. Before calling for assistance...

Performance problems often result from little things you can find and fix yourself without tools of any kind.

Air conditioner won???t run:

lIs unit plugged into a live circuit with proper voltage?

l Is switch turned on?

. Is thermostat set correctly?

. Have you checked your home???s main fuses or circuit breaker box?

l Has the time-delay fuse blown? l Has the local power failed?

Unit blows fuses:

l Are time-delay fuses being used?

l Is an extension cord being used? (Do not use an extension cord to run your air conditioner.)

l Are you waiting two minutes after turning cooling circuit off before trying to restart unit?

Unit turns on and off, or does not cool room: l Is filter clean?

l Are coils clean (both evaporator [inside] and condenser [outside])?

l Is there excessive moisture or heat (open vessel cooking, showers, etc.)?

l Try setting fan to higher speed.

l Try setting thermostat to a cooler settng.

Operating sounds:

l When your room air conditioner is operating normally, you will hear sounds such as:

l Droplets of water hitting the condenser, caus- ing a ???pinging??? or ???clicking??? sound. Water droplets help to cool the condenser.

l Air movement from the fan, especially on high fan speed setting.

l Clicks from the thermostat cycle.

l Sounds also may be caused by house construc- tion - such as vibration of the unit due to wall construction or unsteady window mounting area.

2. If you need assistance?..

Call Whirlpool COOL-LINE@ service assistance telephone number. Dial free from anywhere in the U.S.:

l-800-253-1301

and talk with one of our trained consultants.

The consultant can instruct you in how to obtain

satisfactory operation from your appliance or, if service is necessary, recommend a qualified service company in your area.

3. If you need service???...

Whirlpool has a nationwide network of franchised

1 TECH-CARE@ Service (.7-,ZSER???-&ff-CARE ICompanies...TECH-CARE

service technicians are trained to fulfill the product

warranty and provide after-warranty service, any- where in the United States. To locate TECH-CARE service in your area, call our COOL-LINE service assistance telephone number (see Step 2) or look in your telephone directory Yellow Pages under:

4. If you have a problem???...

Call our COOL-LINE service assistance telephone number (see Step 2) and talk with one of our consultants, or if you prefer, write to:

Mr. Donald Skinner

Director of Customer Relations Whirlpool Corporation

2000 M-63

Benton Harbor, Ml 49022

Please include a daytime phone number in your correspondence.

5. If you need FSP@ replacement parts:..

FSP is a registered trademark of Whirlpool Corporation for quality parts. Look for this symbol of quality whenever you need a replacement part for your Whirlpool appliance. FSP replacement parts will fit right and work right, because they are made to the same exacting specifications used to build every new Whirlpool appliance.

To locate FSP replacement parts in your area, refer to Step 3 above or call the Whirlpool COOL- LINE service assistance number in Step 2.

???If you must call or write, please provide: model number, serial number, date of purchase, and a complete description of the problem. This information is needed in order to better respond to your request for assistance.

15

Whirlpool???RoomAir Conditioner

Warranty

AC00

1.Compressor 4. Drier-Strainer

2.Evaporator 5. Connecting Tubing 3,???Condenser

WHIRLPOOL WILL NOT PAY FOR

A. Service calls to:

1. Correct the installation of the air conditioner.

2. Instruct you how to use the air conditioner.

3. Replace house fuses or correct house wiring.

4. Clean or replace air filter.

B. Pick up and delivery. This product is designed to be repaired in the home.

C. Damage to the air conditioner caused by accident, misuse, fire, flood, acts of God or use of products not approved by Whirlpool.

D. The removal and reinstallation of the air conditioner if it is installed in an overhead or other inaccessible location or not installed in accordance with published installation instructions.

Service under the full warranties must be provided by a franchised TECH-CARE@??? service company.

WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Outside the United States, a different warranty may apply. For details, please contact your franchised Whirlpool distributor or military exchange.

Pat-l No. 510937/789540

01989 Whirlpool Corporation