lvens, Compactors, Room Air Conditioners, Dehumidifiers, Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers,Dishw:

Copy your Model and

Serial Numbers here...

When you need service or call with a question,

page???a

H

BEFORE YOU USE YOUR

AIR CONDITIONER

It is your responsibility to make surethat your air conditioner:

l Has been properly installed.

lIs the right size for the area you want to cool.

l Is properly connected to electricity.

l Is properly electrically grounded.

lIs properly used only for the job it was intended to do.

l Is not used by children or anyone not able to operate it properly.

l Is properly maintained.

l Also, remove energy label and buy guide. Use damp cloth to take off any glue residue. Do not use a sharp instrument or any harsh or abrasive cleaners.

Energy SavingTips

l Improve home insulation (seal doors, windows, and close fireplace flue).

l Close blinds or drapes on sunny side of house; add window awnings.

lKeep air filter clean. Don???t block air flow with drapes or furniture.

l Ventilate attic (high temperature levels add to normal cooling load).

l Try not to use heat producing appliances during the hottest part of the day. Turn lights, radios, televisions, and other appliances off when not needed.

l Keep heat registers and cool air returns closed or blocked off so cooled air won???t escape.

lUse a vent fan in areas where cooking, laundry, or bathing is done to pull out extra heat and moisture near its source.

Contents

2

Electrical Requirements

For Your Air Conditioner

ELECTRICAL REQUIREMENTS ARE DIFFERENT

FOR THE TWO MODELS SHOWN ON THE

COVER, DEPENDING ON THE AMPERE RATING

OF YOUR UNIT. THE NUMBER OF AMPERES IS

PRINTED ON THE SERIAL PLATE, ATTACHED TO

THE FRONT OF THE UNIT, BEHIND THE FRONT PANEL (SEE PAGE 2).

OBSERVE ALL LOCAL GOVERNING CODES

AND ORDINANCES

Do not, under any circumstances, remove the power supply cord ground prong.

RECEPTACLE WIRING

RECEPTACLE WIRING should be at least as large as 14 gauge. Use copper wire only. It is the personal responsibility and obligation of the customer to provide proper and adequate receptacle wiring installed by a qualified electri- cian. OBSERVE NATIONAL ELECTRICAL

CODE AND ALL LOCAL GOVERNING

CODES AND ORDINANCES.

Electrical Requirements

A 115 volt (103.5 min., 126.5 max.) 60 hertz AC only, 15 ampere fused electrical supply is required (time delay fuse or time delay circuit breaker re- quired). It is recommended that a separate circuit, serving only this appliance, be provided for models with serial plate amperes up through 7.5. A separate circuit is required for models with serial plate amperes of 7.6 through 72.0. Do not use an extension cord.

grounding type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician. See Figure 1.

Figure 1

3-PRONG

GROUNDING PLUG

3-???PRONG

GROUNDING

WALL RECEPl ???ACLE

PbWEi-SUPPLY CORD

ALTERNATE GROUNDING METHOD

If changing and properly grounding the wall receptacle is impossible and where local codes permit (consult your electrical inspector), a temporary adapter may be plugged into the existing 2-prong wall receptacle to mate with the 3-prong power supply cord. See Figure 2. THIS,

HOWEVER, IS NOT RECOMMENDED.

If this is done, you must connect the grounded eyelet on the adapter to the wall receptacle cover plate screw and from this same screw, you must connect a separate copper ground wire (#14 minimum) to a grounded cold water pipe.* See Figure 2. Do not ground to a gas supply pipe. Do not connect to electrical supply until appliance is permanently grounded.

GROUND ASSEMBLY

(ATTACH TO GROUNDED

ELECTRICALLY

GROUNDED MET

COLD WATER PI

(REMOVE PAINT

Electrical Connection

Electrical Ground is Required on this Appliance

RECOMMENDED GROUNDING METHOD

For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong

RECEPTACLE

POWER SUPPLY CORD

*Cold water pipe must have metal continuity to electrical ground and not be interrupted by plastic, rubber or other electrically insulating connectors (including water meter or pump) without adding a jumper wire at these con- nections.

3

INSTALLATION INSTRUCTIONS

for Your Air Conditioner

Unpack the mounting parts that came with your air conditioner to determine which window installation instruction you should follow.

If you have these parts, follow:

INSTRUCTION 1 (below).

If you have these parts,

follow:

INSTRUCTION

(on page 8):

Installation

Instructions

CAUTION:

lBe sure air conditioner does not fall out of window during installation.

l Handle the air conditioner with care, Watch out for the sharp metal fins on the front and rear coils.

lDo not use the collected water for drinking purposes. It is not sanitary.

,

1l Unpack mounting parts before installing your air conditioner. Make sure you have all the necessary parts (see Figure 3). A normal installation can be made with a screwdriver, saw, small level, pocket knife, tape measure, drill and %???, 9&??? and 3/16??? drill bits.

Description of Parts

If using Item 13 for fastening Item10 or 12 to metal or plastic, use 9/64-in. die. or #26 drill.

2l Pick the right window. First, decide what room(s) you want to cool. Then choose a window that will allow the air-conditioned air to flow freely and directly into the room(s) you want cooled. Remember, it???s difficult to move air around corners. If the inner sliding window slides to the left, the unit will be installed on the right. Remove window screen if there is one. Choose a sliding window that???s also near an electrical outlet. (Refer to the ELECTRICAL REQUIREMENT page for type of receptacle and wiring needed.) Do not use an extension cord. The sliding window in which you place your air condi- tioner should have an opening of at least 15-l/2??? wide and 21 -l/4??? to 40.7/8??? high (see Figure 4). For installations up to 62. l/4??? high, a special kit (Part No. 977449) is available. For windows as low as 20.7/16???, you must install without filler frame and remove top angle on unit, reinstalling 3 screws into top of cabinet.

This model may also be installed in steel hinged casement windows. The steel hinged case- ment window must have an opening at 15-l/2??? wide and no more than 16-l/2??? wide.

Figure 4

3l Place shelf in window with tabs against the track surface (see Figure 5).

4l Install support bracket (Item 2) with either short or long leg down and with end of bracket either toward or away from window, depend- ing upon construction and depth of wall and window sill (see Figure 6). Install sill bracket (Item 3). Each bracket is attached using one 5/16??? bolt, nut and washers (Items 4, 4A, 4B and 4C).

Figure 6

50 Reinstall assembled shelf with two brackets into the window opening. Adjust brackets until shelf is firmly seated and sloping down to outside. If you use a level, be sure you have l/2 bubble of slope. Without a level, place the translucent panel (Item 5) on shelf. The top of long side of the panel will be 5/16??? back from the window line (see Figure 7).

Figure 7

6l If slope back is correct, tighten all nuts se- curely. Install lower track seal (Item 4) shown in Figure 8. This track seal has two holes which line up with matching screw holes in shelf.

7l Install shelf 2-3/8??? from side of window opening (see Figure 9).

8l Measure height of opening (see Figure 9). Subtract 20-9116 ??? from measured height. This will be the actual height of translucent panel

Figure 9

c 2-3/B???

9l Measure out the distance from Figure 9 and mark it along the 20-l ???4??? side of translucent panei. Clamp panel between a board and an appropriate supporting surface close to mark and cut with fine tooth saw (see Figure 10.) Remove burrs.

10l Lift vertically and remove panel frame from unit. Slide translucent panel into groove in frame, keeping honeycomb side to the face side of frame (see Figure 11). Slide frame back into place on unit. Panel should enter the top angle groove.

Figure 11

PLAIN SIDE -

11l Peel backing from seal strip (Item 8) and press it onto side filler frame guides on each side of unit (see Figure 12).

Figure

CUT OFF EXCESS

LENGTH BELOW UNIT.

12. Place unit in window by resting unit on shelf. Push unit towards window so side angles are sealing against the side jamb stop (see Figure 13). Slide the opened window sash firmly to side of unit. Push unit and filler frame to make certain the frame and unit sealing strips are sealing

Figure 13

SEAL

STRIP

c

SEAL STRIP

HONEYCOMB SIDE

???\

ADD SCREWS???

14l Lock the sliding sash at bottom using lock bracket (Item 10) and screw (Item 7) as shown in Figure 15. Use a l/8??? drill bit to drill through track before inserting screw.

17l FOR INSTALLATION IN STEEL

CASEMENT WINDOWS.

Follow Steps 2 and 3 on page 5. NOTE: in Step 3, the shelf tabs must butt to the front of the bottom angle on the casement (see Figure 18).

Jre 18

ROOM SIDE

/

e

(ROOM SIDE)

13 . Cut seal strip (Item 11) to length. Install it between space of opened sash and glass of the closed sash (see Figure 16).

18l When Step 3 is finished, follow Steps 4, 5, and 6 on page 5; Steps 7, 8, 9, 10, 11 and 12 on page 6. Then follow Steps 19 and 20 on page 7 and 8.

19l Open window at least 180??? to allow room for unit cabinet. If necessary, remove window crank handle so the window will open wide enough and not interfere with shelf against the bottom sill angle. Tie opened window to the wall or frame to prevent the window from swinging.

7

Figure 19

15-112??? MIN.

IG

UNIT

1 14-112???+

CENTER UNIT IN

20. Drill g/64??? holes in the window jamb top to line up with holes in filler frame (see Figure 19). Use two thread cutting screws (Item 13) to secure unit. If you need additional hold- ing strength, add to screws at the bottom of the unit side channels (see Figure 14 on page 7).

1l Unpack mounting parts before installing your air conditioner. Be sure you have all the necessary parts (see Figure 20 and 21). This air conditioner will fit most steel casement windows. A normal installation can be made with a screwdriver, 5/16??? socket driver, tape measure and drill.

Figure 20

z Installation

Instructions

CAUTION:

lBe sure air conditioner does not fall out of window during installation.

l Handle the air conditioner with care. Watch out for the sharp metal fins on the front and rear coils.

lDo not use the collected water for drinking purposes. It is not sanitary.

3.Bottom fvlounting Bracket

NOTE: Abova Parts (Not Shipped Loose) installed on unit by factory.

2. Pick the right window. First, decide what room(s) you want to cool. Then choose a window that will allow the air-conditioned

air to flow freely and directly into the room(s) you want cooled. Remember, it???s difficult to move air around corners. Choose a window that???s also near an electrical outlet. (Refer to the ELECTRICAL REQUIREMENT page for type of receptacle and wiring needed.) Do not use an extension cord. To be able to use the window mounting parts shown in Figure 20, the window should have a minimum width of 14-l/2??? and maximum width of 16??? (see ???A??? in Figure 22). The window should

8

Remove the glass from the frame opening selected. Clear away any hardened putty.

Before sliding unit through the casement opening, remove the bottom window bracket (Item 3) on both sides of the unit. NOTE: only the top screws (Item 1) need to be removed.

Check the knurled knob screws to see that the top mounting brackets (Item 5) are retracted to the center of the unit. They must not inter- fere with the window frame when the unit is installed (see Figure 23).

6l Lift the unit into the window opening and slide it back until the mounting frame comes into contact with the window frame (see Figure 24).

them loose enough so there is about l/16??? of play. Tighten the bottom screws (Item 2). This will pull the unit mounting flange tightly to the window frame, sealing and locking the air conditioner in place.

WIN[IOW FRAA(IE

8 . Loosen the two knurled knob screws and slide the top mounting bracket (Item 5) toward the outside of the unit, engaging the window frame (see Figure 26). Tighten the knurled knob screw in this position. This will lock the unit in place so it cannot tilt into the room. The installation is now complete.

WE% s)taWlM OUTSIt% OF WBJOOW

9l OPTIONAL MOUNTING INSTRUCTIONS

If the window thickness will not allow you to use the four mounting brackets provided with the unit, remove brackets and fasten flanges of unit with sheet metal screws (see Figure 27). These screws are not provided. The window opening for your installation must not be wider than 15???.

HOW TO START AND USE

YOUR AIR CONDITIONER

THERMOSTAT

CONTROL

FAN SPEED

CONTROL

EXHAUST FAN SPEED THERMOSTAT

CONTROL CONTROLCONTROL

Be sure air conditioner is OFF before plugging it in.

To Start Your Air Conditioner

1l Set exhaust control (if your unit is so equip- ped) to CLOSED for maximum cooling.

2l Choose either LO COOL or HI COOL fan speed setting.

LO COOL . . . . . . . . . . for sleeping comfort

HI COOL . . . . . . . . . for maximum cooling

FAN ONLY . . for circulating room air when no cooling is desired

The Exhaust Control

The Exhaust Control setting draws stale or smoky air from the room.

1. To exhaust room air

Set exhaust control to OPEN. Adjust fan control to speed desired. If no cooling is desired, use FAN ONLY setting.

OPEN FAN ONLY

3l Turn the thermostat control to number 6 (mid-setting). You can adjust the air condi- tioner???s cooling performance by resetting the thermostat control to a higher number for maximum cooling. Lower the number setting for less cooling. You will need to experiment to find the setting which suits you best.

10

2. To circulate room air

Set exhaust control to CLOSED. Adjust fan control to FAN ONLY.

CLOSED FAN ONLY

ChangingAir Direction

The louvers in the grille area at the top of the air conditioner control the direction of the cooled air.

1l If your unit looks like Figure 28, move the lever at top of the grille to the right, left or straight ahead. Simply move the lever in the direction you want the air to go. The rear vertical louvers in the grille can be adjusted left or right or straight ahead. The front set is fixed and directed upward.

Figure 28

2l If your unit looks like Figure 29, turn the cir cular air discharge grrlles on top of the unit. Both grilles can be adjusted to the right or left, or adjusted individually.

Cleaningand Caring fdr Your Air Conditioner

Proper use and care of your air conditioner will help insure longer life and lower operating costs. Follow these instructions carefully. Call your dealer for an annual checkup.

Cleaningof Front Panel

1l Remove the front panel from unit when cleaning. Press down at top edge of the front as shown in Figure 30 or 31 (depending on your model).

2l When the front moves away from top of cabinet, pull top of front toward you.

3l Lift up and away from the bottom spring clips.

4l Clean front panel with warm water and mild soap or detergent. Use a soft cloth. Rinse and dry. Replace front panel.

5l Wipe control panel clean with a soft dry cloth.

11

CleaningAir Conditioner Filter

The filter is cleanable. A clean filter helps remove dust, lint and other particles from the air. Check every two weeks to see if filter needs cleaning.

1l Remove filter by releasing it from plastic clips as shown in Figure 32 or 33 (depending on your model).

20 Clean filter, using a vacuum cleaner.

-OR-

3l If very dirty, wash filter with warm water and mild detergent. Air dry thoroughly before replacing.

Figure 32

- CLIPS

- FILTER

Figure 33

CLIPS

FILTER

Annual Maintenance for Your

Air Conditioner

Your air conditioner needs annual maintenance to help insure steady, top performance throughout the year.

:__

Call the service company recommended by your dealer to:

l Inspect and clean the coils and condensate water passages.

l Check fan and oil the fan motor.

l The compressor is sealed and needs no oiling.

Expense of annua! inspection is customer???s responsibility.

- or -

If you are familiar with electrical appliances, you can do the cleaning and maintenance yourself. Ifs you decide to go ahead, follow these steps:

1l REMOVE UNIT FROM CABINET. Wrap the motor, electrical control box and electrical terminals box in plastic film and make sure no water or other liquid gets inside any of these parts. It could damage the insulation and cause serious trouble.

2. Carefully clean and hose out the base, coils and condensate pans. Clean at least once a year or more often if the condenser coils and pans collect dirt, sand, leaves, insects or algae. Also, clean if you detect an odor from the air conditioner. While the cabinet is open, this is a good time to oil the fan motor.

3l Remove plastic film from motor and electrical parts.

4 . Replace unit in cabinet.

NOTE: It???s a good idea to wait 24 hours before starting the unit again. This aliows time for all areas to dry out. The water from rainfall or from normal operation does not harm these components.

12

Oiling of the Fan Motor

Notes:

1l Oil the fan motor per instructions on the motor. To add oil, pull out the oil hole plug at each end of the motor. (see Figure 34).

OIL PLUGS

An easy to use one-ounce capsule of especially recommended oil (Part No. 10943) can be ordered from your dealer.

2. Replace the plug to keep dirt from motor bearings.

3l Reinstall the unit in cabinet after performing maintenance. (See Installation Instructions.)

COOLING LOAD GUIDE-SQUARE FEET METHOD

ROOM AIR CONDITIONERS

To make sure you choose the right size umt. use this COOLING LOAD GUIDE -

SQUARE FEET

METHOD It IS a quick. easy means of computing capacity

For WIWIXS In e~praure shading lnsulallon and bulldlng construction AHAM Cooling Load Esllmate Form FtAC~l must be used

2000

I800

1600

I400

1200

1000

800

600

400

200

COOLING CAPACITY REQUIRED-BTU/HR

INSTRUCTIONS:

1.Determine lhe area to be cooled I??? square feet and locate lhal polnl on lhe left side of chart

2.Move horizontally across lo the center line of Band A, B or C according to the condmon of the celling In the area lo be cooled Band A-Occupied Space Above Celling

0end B-Insulated Celling Under Attic Bmnd C-Non-Insulated Celling Under AttIc

3.From center of band move wthm the band to lett lor more northerly exposure or rlght for more westerly exposure

4.From thls point. read down to bottom of chart to determine

required Bluihr output Write the Btuihr figure In the space lndlcated below

A-1

Room Air Conditioner

5.- Btuihr (from number 4 above)

6.Locale your qeographlc area on lnsel map and multiply factor showhbytlgure In number 5

7.~~ If room air condltloner IS Intended orlmarllv for moht- time cooling. subtracl 30% (from hg;re In nimber 67

10..~ Add 4000 Btuihr (lo figure In number 9) II area lo be

cooled Includes kitchen

For best resulls, a room condltlonmg unll or units with a cooling capaclly rallng close to that estlmaled above should be selected

A smaller capacity umt operatmg continuously ~111 contrlbute more to comfort than a larger capacity unit operating Intermit- tently

14

If you needserviceor assistance,we suggestyou follow thesefour steps:

1. Before calling for assistance

Performance problems often result from little things you can find and fix yourself without tools of any kind.

Unit won???t run:

1.Is unit plugged in?

2.Is switch ON?

3.Is thermostat set too WARM?

4.Is time-delay fuse blown?

5.Has local Dower failed?

Unit blows fuses:

1.Are time-delay fuses used?

2.Is an extension cord being used? (Do not use.)

3.Are you waiting two minutes after turning cooling circuit off before trying to restart unit?

Unit turns on and off, or does not cool room:

1.Is filter clean?

2.Are coils clean? Both evaporator (inside) and con- denser (outside)?

3.Is there excessive moisture or heat? (Open vessel cooklng, showers, etc.)

4.Set fan to higher speed.

5.Set thermostat to a cooler setting.

I. If you need assistance

Call the Whirlpool COOL-LINE@ service assistance telephone number. Dial free from:

Continental U.S. . . . . . . . . . (800) 253-1301 Michigan . . . . . . . . . . . . . . . (800) 632-2243 Alaska & Hawaii . . . . . , . . . (800) 253-l 121

and talk with one of our trained Consultants. The Consultant can instruct you in how to obtain sat- isfactory operation from your appliance or, if ser- vice is necessary, recommend a qualified service company in your area.

3. If you need serviceWhirlpool has a nation- wide net work of fran- chaised TECH-CARE@

,%@11service Companies. TECH-CARE service technicians are trained to fulfill the product warranty and provide after-warranty service,

anywhere in the United States. To locate TECH- CARE service in your area, call our COOL-LINE service assistance telephone number (see Step 2) or look in your telephone directory Yellow Pages under:

4. If you have a problem

Call our COOL-LINE service assistance telephone number (see Step 2) and talk with one of our Consultants, or if you prefer, write to:

Mr. Robert Stanley Division Vice President Whirlpool Corporation 2000 US-33 North

Benton Harbor, MI 49022

If you must call or write, please provide: model number, serial number, date of purchase, and a complete description of the problem. This informa- tion is needed in order to better respond to your request for assistance.

made lo the same exacting speclficailons

used b build every new Whirlpool appliance

15

!ifiers, Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers, Dishwashers, Built-In Ovens and Surface Units, Ranges,Micr