Viking Memory

I N S T A L L A T I O N G U I D E

TEXAS INSTRUMENTS??

Extensa 390 Series

Manual No. 1005200 ??? Release 07/98, Rev. C

S P E E D P O W E R P E R F O R M A N C E

The Texas Instruments Extensa 390 Series comes standard with 16MB or 32MB of removable memory. It can be expanded to a maximum of 128MB* by installing the following Viking Components memory options into its two available expansion slots.

*Requires the removal of all standard memory.

Caution:

Electro Static Discharge (ESD) can damage electronic components. Before touching the memory module, ensure that you are discharged of static elec- tricity by touching a grounded metal object.

5. Locate the two memory expansion slots in the open compartment. There will be at least one memory module occupying an expan- sion slot. Notice the location of the off-cen- ter key on each of the expansion slots.

6. To expand your system to 128MB, the standard memory will need to be removed. If you do not need to remove a memory module before your installation, please proceed to step 7. Locate the metal retain- ing clips on both sides of the memory module. Gently pull both clips away from the mod- ule. Then lift the module out of

its expansion slot.

7.To install a memory module, insert the module into the expansion slot at an angle and then push it down until it clicks into place. To be certain that the module is installed correctly, ensure that the off-center notch on the module is aligned with the off-

center key of the expansion slot. The module can only be installed one way due to the position of the notch.

8.Replace the memory expansion

cover to its original position and be sure to secure its three holding screws.

9.Insert the battery back into its compartment. Replace the AC power supply and any other cables you may have disconnected.

10.Turn the system on. The computer will automatically reconfigure itself to recognize the newly added memory. The new memory can be verified during the POST routine at start-up and at the SETUP utility.

The installation is now complete.

INSTALLATION INSTRUCTIONS:

1. Turn the computer off and disconnect the AC power supply and any

WARRANTY & DISCLAIMERS:

other cables from the unit.

Note: If the unit appears to be powered down, ensure that it is not in Suspend mode.

2.Remove the battery from the system. If you are not familiar with this procedure, please refer to your computer???s ???Owner???s Manual.???

3.With the computer display closed, turn the unit upside-down.

4.Locate the memory expansion cover towards the right-side of the bottom panel. Also locate the three holding screws on the cover. Remove only these screws with a small Phillips screwdriver. Then remove the memory expansion cover by lifting it up.

All Viking Components products have been thoroughly tested free of defects in material and workmanship. If any malfunction should occur while using one of our products in its recom- mended environment, Viking, at its option, will repair or replace the product at no charge, pro- vided the product or any part thereof has not been abused, misused, neglected, replaced, repaired or modified. Viking shall make the final determination as to the existence and the cause of any defect. Viking will not repair or replace products designated as having a ???Limited Lifetime??? which fail solely because their estimated life has expired. No warranty is made with respect to customer products produced to original purchaser specifications except as specifi- cally stated in writing by Viking.

All shipping costs shall be the responsibility of the purchaser.

Except as provided herein, there are no express or implied warranties of merchantability or fit- ness for a particular purpose. Under no circumstances will Viking Components be liable in any way to the purchaser for any damages, including but not limited to lost revenue, lost wages, or any other incidental or consequential damages arising out of the use of or inability to use this product. Viking reserves the right to make modifications in both hardware and soft- ware without prior notifications.

All Viking Components are 100% guaranteed compatible with the OEM machines for which they are designed. All OEM's names, trademarks and part numbers are used for identification purposes only, and in no way imply that any of our products are original equipment parts.

Texas Instruments is a registered trademark of Texas Instruments, Inc.

Extensa is a registered trademark of Acer American Corporation and Acer Inc.