UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page a

Quick Start

Guide

WDECT 2300

Wide Band Digital Technology provides the clearest sound and the best privacy.

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page i

INSTALLATION & SAFETY

Choosing the best location for your phone.

When choosing a location for your phone there are a number of appliances the phone should not be near, and areas you should avoid.

???This symbol indicates important operating and servicing instructions.

???The earcap of this telephone may attract and retain small metallic objects.

[ i ]

AVOID -

Television sets and other electronic appliances

CHOOSE -

a central location

AVOID -

Microwave ovens

AVOID - moisture

AVOID -

Computers

AVOID -

other cordless telephones

AVOID - connecting more than

3

phones as ringing may be impaired

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page ii

Installing the Base Unit

1)Connect the AC adapter to the DC IN 9V jack and to a standard AC wall outlet.

2)Connect the telephone line cord to the TEL LINE jack and to a telephone socket on the wall.

For wall mounting, see ???Mounting the Base Unit on a Wall??? on page 5.

Route the cord.

To telephone socket

New Zealand

To TEL LINE

Make sure the AC Adapter remains switched ON at all times. Use only the Uniden AC Adapter supplied with this unit.

[ ii ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page iii

???Charge the handset battery pack for at least 15-20 hours before using your new cordless telephone for the first time.

???Use only the Uniden rechargeable battery pack (BT-446) supplied with your cordless telephone.

[ iii ]

3) Set the base on a desk or tabletop.

Installing the battery pack

1)Press down on the battery cover release and slide the cover down until it comes off.

2)Connect the battery plug to the socket at the rear of the battery compartment. The RED and BLACK battery wires must match the RED and BLACK dots on the phone case for the plug to fit properly. Press firmly until it clicks

into place.

3)Securely close the battery compartment cover by sliding it up until it snaps into place.

Black Red

Wire Wire

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page iv

Charging the handset

1) Place the handset in the base unit with the keypad facing forward.

2)Make sure the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the base charging contacts.

???After installing the batteries in the handset, charge your handset at least 15-20 hours.

Recharge your phone on a regular basis by returning the handset to the base after each phone call.

During a power cut or if the AC adapter is switched off, this telephone

will not operate.

[ iv ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page v

CONTENTS

[ v ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 1

CONTROLS AND FUNCTIONS

3

4

8

9

10

5

11

12

13

1.Handset Antenna

2.Headset Jack Cover

3.Beltclip Hole

4.Hands-Free Speaker

5.Handset Battery Compartment

6.New Message LED

7.Handset Earpiece

8.LCD Display

9. /del Key

10. /vol/ / Key

14a. ringer volume control

b. scroll keys for display screen

1511. Key

1612. redial/pause Key

1713. speaker Key

14. Key

15. Key

1816. Key

1917. Key

GETTINGSTARTED [ 1 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 2

Base

23

24

25

26

23. Base Antenna

24. Base Charging Contacts

25. charge LED

26. Key

[ 2 ]

2728

27.TEL LINE Jack

28.DC IN 9V Jack

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 3

UNIDEN COMPANY PHILOSOPHY

To bring outstanding wireless communication products to people???s lives throughout the world.

WELCOME

Congratulations on your purchase of this Uniden cordless telephone. This is designed for reliability, long life and outstanding performance utilising the latest in 2.4GHz Digital Spread Spectrum Technology.

Note: The illustrations in this manual are intended as a guide and may differ from actual unit.

FEATURES

Great features of this cordless phone include:

???Designed and Engineered in Japan

???Wide Band Digital Technology

???Digital Duplex Speakerphone on Handset

Advanced Alpha Display Caller ID Features:

???Alpha Memory Dialling

???POP ID - Caller Name Identification*

???20 Individual Caller Allocations

???50 Caller ID* Memories with Phonebook

???3 Line Full Dot Matrix LCD Display with Clock

???Maxi-Sound - Extra Loud Handset Volume Control

???And More!

*Caller ID and POP ID features work only if you subscribe to the service provided by your local telephone company. There is usually a fee for this service.

[ 3 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 4

CHECKING THE PACKAGE CONTENTS

Make sure you have received the following items in the package. If any of these items are missing or damaged, contact your retailer.

???Base unit (1)

???Handset (1)

???AC adapter (1)

???Rechargeable battery pack (1)

???Linecord (1)

Also included:

???This Owner???s Manual

???Other Printed Material

TERMINOLOGY

Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation.

Standby Mode - The handset is not in use, is off the cradle, and or speaker has not been pressed. A dial tone is not present.

Talk Mode - The handset is not in the cradle and or speaker has been pressed enabling a dial tone. ???Talk??? appears on the display.

[ 4 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 5

MOUNTING THE BASE UNIT ON A WALL

You can mount your base directly to the wall. Before doing this, consider the following:

???Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.

???Mount your phone within distance of a working phone jack.

???Make sure the wall material is capable of supporting the weight of the base and handset.

???Use screws with anchoring devices suitable for the wall material where the base unit will be placed.

1)Insert two mounting screws into the wall (with their appropriate anchoring device), 85mm apart. Allow about 3mm between the wall and screwheads for mounting

the phone.

2)Plug the AC adapter into the DC IN 9V jack on the telephone and then into a Standard AC wall outlet.

3)Plug the telephone line cord into the TEL LINE jack on the telephone and then into the telephone socket on the wall.

4)Align the mounting slots on the base with the mounting posts on the wall.

5) Then push in and down until the phone is firmly seated.

This phone also can be mounted on any standard telephone wall plate (for Australia).

3mm

85mm

[ 5 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 6

BATTERY MAINTENANCE

Battery use time (per charge)

Fully charged

???Up to 7 hours continuous use.

???Up to 10 days when the handset is in the standby mode.

Recharge your phone on a regular basis by returning the handset to the base after each phone call.

Low battery alert

When the batteries are very low and need to be charged, the phone is programmed to eliminate functions in order to save power.

The batteries need to be charged when:

If the phone is in the standby mode, none of keys will operate. If you are on a call, complete your conversation as quickly as possible, and return the handset to the cradle.

Cleaning the battery charging contacts

To maintain a good charge, it is important to clean the charging contacts on the handset once a month. Use a dry cloth or pencil eraser to clean.

[ 6 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 7

Battery replacement and handling

When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery.

Caution

???Use only the specified Uniden battery pack (BT-446).

???Do not remove the batteries from the handset to charge them.

???Never throw the battery into a fire, disassemble them, or heat them.

???Do not remove or damage the battery casing.

To avoid the risk of personal injury or property damage from fire or electrical shock, only use the

Uniden battery model and Uniden adapter model specifically designated for this product.

[ 7 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 8

HEADSET INSTALLATION

Your phone may be used with an optional headset, the Uniden HS910. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations. Headset is available through Uniden authorized retailers.

DISPLAY AND ICONS

Example of the standby mode display

[ 8 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 9

ABOUT THE MENU OPTIONS

There are 3 main menu options, (Handset Setup, Global Setup and System Reset) and submenu options.

Summary of the Main Menu and Submenu

Handset Setup

???During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and the handset is within range of the main base unit.

???Direct Link, Room Monitor, and Copy Phonebook features are not functional on this model.

[ 9 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 10

Global Setup

System Reset

System Reset is used to clear the handset???s ID from the main base unit, or the base ID from the handset.

[ 10 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 11

SETTING UP THE MENU

Entering the Menu

3)Press to select the desired main menu.

4)Use /vol/ or /vol/ to select a desired submenu, and then press

to enter.

In the submenu, use /vol/ or /vol/ to select an item. Press to confirm your selection. For detailed instructions, see the following sections for the

???To back to the

previous screen, press /del.

???Direct Link, Room Monitor, and Copy Phonebook features are not functional on this model.

Handset Setup

Programming your Voice Mail Access Number

1)Enter the Handset Setup menu, and then the Edit Voice Mail submenu (see ???Entering the Menu??? on page 11).

Edit V_mail No. appears.

Edit V_mail No. 1234567890

2)Enter your personal access number using the number keypad (0-9),

, , /del, or redial/pause (up to 20 digits).

3)Press . You will hear a confirmation tone.

To delete the current Voice Mail Access Number, delete all numbers in step 2 using

/del and .

[ 11 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:52 AM Page 12

-Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]

-Polyphonic Tones [Beethoven???s Symphony #9 (Beethoven9), For Elise (Elise), We Wish You A Merry Christmas (Merry-Xmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6 (Lorri Song), When the Irish Eyes Are Smiling (Irish Eyes), Aura Lee, Let Me Call You Sweet Heart (Sweetheart), Waltzing Matilda (W Matilda), Old MacDonald (Old MacDld)]

Distinctive Ringer Setup

Setting the AutoTalk

1)Enter the Handset Setup menu, and then the Auto Talk submenu (see ???Entering the Menu??? on page 11).

Distinctive Ring

On

Off

Auto Talk

On

Off

[ 12 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 13

Setting the Anykey Answer

Setting the True Banner

1)Enter the Handset Setup menu, and then the Banner submenu (see ???Entering the Menu??? on page 11).

2)Use the number keypad (0-9), , , or

/del to enter or edit the name.

3)Press . You will hear a confirmation tone.

Anykey Answer

On

Off

Banner

_________ #1

Setting the Key Touch Tone

1)Enter the Handset Setup menu, and then the Key Touch Tone submenu (see ???Entering the Menu??? on page 11).

Key Touch Tone

On

Off

[ 13 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 14

For setting the Day and Time, the idle time-out is extended to 2 minutes.

Global Setup

Setting Name Tag (POP ID)

1)Enter the Global Setup menu, and then the Name Tag submenu (see ???Entering the Menu??? on page 11).

Setting Insert Zero (New Zealand only)

1)Enter the Global Setup menu, and then the Insert 0 submenu (see ???Entering the Menu??? on page 11).

Setting Day and Time

3)Press /vol/ or /vol/ to set hour and then press .

[ 14 ]

Setting the Dial Mode (Australia only)

1)Enter the Global Setup menu, and then the Dial Mode submenu (see ???Entering the Menu??? on page 11).

2)Press /vol/ or /vol/ to change the select, Tone or Pulse (the initial setting is Tone).

3)Press . You will hear a confirmation tone.

Dial Mode

Tone

Pulse

Deregister HS? Yes
No

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 15

System Reset

De-register the Handset

4)Press . You will hear a confirmation tone. When de-registration is complete, Deregistration

Complete appears.

5) After de-registering the handset, move to ???Replacing the Base Setting??? below.

Replacing the Base Setting

3)Press . You will hear a confirmation tone. The base information will be deleted.

When replacing the base is complete, Place handset on main base to register appears, register the handset to the new base.

4)Place the handset in the base unit to begin registration.

5)While the handset is registering, ???Handset Registering??? will appear in the LCD. When ???Registration Complete??? is displayed, the handset has been registered to the base.

If ???Registration Failed??? appears, please try these steps again.

Make sure to perform the Replacing Base after de-register

the handset.

[ 15 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 16

???To set Autotalk, see page 12 or to set Anykey Answer see page 13.

???The handset microphone is located at the bottom of the handset (see ???Controls and Functions??? on page 1). Position yourself as near to the handset as possible and speak clearly.

BASICS

[ 16 ]

MAKING AND RECEIVING CALLS

This handset has a built-in speakerphone that allows you to have a hands-free conversation. This feature allows you to communicate easily while performing other tasks, such as cooking. appears during hands-free conversations.

You can easily switch a call from normal conversation to hands-free conversation. To switch a call, press speaker during the call.

To enter a pause When you dial the number, press redial/pause. within the ???P??? appears in the display, which represents a pause. dialing sequence

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 17

KEYPAD LOCK

The Keypad Lock prevent user from pressing the keypad accidentally. You can still answer calls, and receive page and phonebook locations, and the keypad lock is reactivated after the operation.

To lock the keypad

Press and hold until you hear a confirmation tone.

Keypad Locked appears.

If anykey is pressed when keypad is locked,

To unlock keypad press & hold * key appears.

To unlock the keypad

Press and hold again. Keypad Unlocked appears.

PLACING A CALL ON HOLD

1)During a call, press /transfer/int???com. The call will be put on hold.

2)To talk to the caller, press or speaker on a handset. The phone will return back to the call.

SUN 12:00A

Handset #1

Line On Hold

You can hold a call for 5 minutes, when 5 minutes has passed, the call is disconnected and the phone returns to standby mode.

[ 17 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 18

???If the number exceeds 32 digits, only the first 32 digits are retained in redial memory.

???If the redial memory is empty, you will hear a beep.

REDIALING A CALL

The last three phone numbers dialed can be quickly redialed.

Redialing from Standby Mode

1)Press redial/pause in standby mode.

2)Press redial/pause again. Each press of

redial/pause will display one of the last three number redialed.

3)Press or speaker. The selected number is dialed.

4)To hang up, press .

Redialing from Talk Mode

1)Press or speaker.

2)Press redial/pause. The last number dialed will be displayed and redialed. To hang up, press .

Deleting a Redial Record

1)Press redial/pause in standby mode.

2)Press redial/pause repeatedly to display the number to be deleted.

3)Press /del.

<Redial1>

8007303456

redial/pause

<Redial2>

2145452930

redial/pause

<Redial3>

8175551212

redial/pause

Delete Redial1?

Yes

No

[ 18 ]

Storing a Redial Record

1)Press redial/pause in standby mode.

2)Press redial/pause repeatedly to display the number to be stored.

3)Press . Store/Edit Name appears.

4)To complete the setting, follow the steps 3-8 in ???Storing Phone Numbers, Names, Distinctive Rings, and Speed dial??? on page 24-25.

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 19

ADJUSTING THE HANDSET RINGER, EARPIECE AND SPEAKER VOLUME

Handset ringer volume

Press the volume up key or volume down key (labeled as /vol/ or /vol/ in standby mode to select one

of three ringer volume (off, low, or high).

Earpiece and speaker volume

Pressing the volume up key or volume down key (labeled as /vol/ or /vol/ key) during a call will change

the earpiece and speaker volume of the handset. This setting will remain in effect after the telephone call has ended.

When you press volume up key ( /vol/ ) in the maximum volume level or volume down key ( /vol/ ) in the lowest volume level, an error tone sounds.

Ringer Mute

You can temporarily mute the incoming ring. When the handset is off the cradle and the phone is ringing, press . The incoming ring will return to the previous setting starting with the next incoming call.

Standby Mode - The handset is not in use and has not been pressed.

[ 19 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 20

???The tone feature only applies when the dial mode is set to pulse.

???This special number can be stored in a memory location. This is referred to as Chain Dialing (see page 31)

[ 20 ]

MUTE MICROPHONE

You can temporarily turn off the microphone so that the person you are talking with cannot hear you.

1)Press /del during talk mode (while phone is in use).

2)Press /vol/ or /vol/ to move the pointer to Mute and then . Mute On and appear in the display. To cancel muting, repeat above step again when Mute is set to on, Mute Off appears.

TONE DIALING SWITCH-OVER (AUSTRALIA ONLY)

Some telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch-over to tone dialing during the call. This feature is useful when you need tone dialing to use automated systems, for example, entering your bank account number after you have called your bank.

Initially make your call with the pulse dialing mode. Once your call connects, press . Enter the desired number. These digits will be sent as tone dialing. Once the call ends, the tone mode is canceled and pulse dialing mode resumes.

TRAVELING OUT-OF-RANGE

During a call, as you begin to move your handset too far from your base unit, noise may increase. If you pass the range limits of the base unit, you will hear a beep and see Out of Range on the display, and then the handset returns to standby mode.

You may return to the call if you move your handset within the range limits of the base and press or speaker within 30 seconds.

UP349BH (WDECT2300) ENG OM 5/12/04 10:53 AM Page 21

CLARITY BOOSTER

1)Press /del during talk time (while phone is in use).

2)Press /vol/ or /vol/ to move the pointer to Clarity Boost, and then .

Boost On and B appear in the display.

To turn Off the Clarity Booster, repeat above step again when the Clarity Booster is on, Boost Off appears.

???Normally, the talk time duration is 7 hours, however, when the Clarity Booster is On, the talk time duration will be up to 5 hours with fully charged batteries.

???Clarity booster automatically turns off after each call.

[ 21 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 22

If the battery pack is completely drained, the handset will not beep when paging.

FIND HANDSET

To locate the handset, press on the base when the base is in standby mode. The handset beeps for 60 seconds, and ???Paging??? appears on the handset display. To cancel paging, press any key on the handset or on the base.

FLASH AND CALL WAITING

If you have Call Waiting service and a call waiting tone sounds while you are on a call, press to accept the waiting call. There is a short pause, and then you will hear the new caller. To return to the original caller, press again.

[ 22 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 23

USING ONE TOUCH VOICE MAIL ACCESS

If you subscribe to voice mail service, you can use your phone to access your voice mailbox. The new message LED flashes whenever you have messages waiting in your voice mailbox. Just program the handset with your access number, and you can get your messages at the touch of a button on the handset. (The voice mail service provider will supply you with the access number. This number may be simply a phone number. Refer to the provider???s literature).

??? To program or delete your Voice Mail Access Number, See page 11.

Dialing your Voice Mail Service

Once you???ve programmed your personal access number, you can dial your mailbox with the touch of a button. When you have messages, simply pick up the handset and press . If you have not entered the access number or it has been deleted, when you press the , No Number Stored To store number press [MENU] appears and you will hear a beep. The phone returns to standby mode.

Voice Mail Access

The new message LED on the handset is designed to work with your voice mail service provided by your local telephone company. The LED flashes when you have new incoming messages in the voice mail service. You may need to occasionally reset the indicators if they remain on after you???ve retrieved your messages. To reset the indicators, when the phone is in standby mode press and hold on the base until the paging sound stops (about 5 seconds).

???You must subscribe to voice mail service from your telephone company in order to use this feature. The voice mail service company will provide you with the access number.

???Voice Mail Access Numbers : Australia

Message Bank : 125101

Home Messages : 101 New Zealand

Call Minder : 083210

[ 23 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 24

PHONEBOOK

The Phonebook allows you to dial a number using just a few key presses. Your phone stores names/numbers in the phonebook memory location, and you can search names in alphabetical order. You have a total of 100 locations that can be used for the phonebook (including the speed dials) and Caller ID messages (up to 50 locations).

STORING PHONE NUMBERS, NAMES, DISTINCTIVE RINGS, AND SPEED DIAL

1)When the phone is in standby mode, press phonebook.

The handset displays the following items:

(1st line) The number of the phonebook locations used (2nd line) How to search (press the number keypad,

/vol/ or /vol/)

(3rd line) How to enter the storing operation (press the key)

Phonebook :100

Search [A-Z/ / ]

Store [SELECT]

[ 24 ]

2)Press , Store/Edit Name appears.

3)Enter the name (up to 16 characters) by using the number keypad (see the ???Steps for Entering Names and Special Characters??? on page 26).

If a name is not required, go to step 4. <No Name> will be used as the name.

4)Press to store the name,

Store/Edit No. appears.

5)Press the number keypad to enter the phone number (up to 20 digits), press to store

the number.

Store/Edit Name

Movies

Store/Edit No. 8007303456

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 25

6)Distinctive Ring appears. Press /vol/ or

/vol/ to move the pointer to one of the Distinctive Ring options, and then press .

If you choose not to store a Distinctive Ring, simply select the ???No Selectn??? option.

Distinctive Ring

No Selectn

Flicker

7) Speed Dial appears. Press /vol/ or /vol/ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0).

If you choose not to store the name/number as a Speed Dial, simply select the ???No Selectn??? option.

Speed Dial

No Selectn

SPD1:<Empty>

[ 25 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 26

STEPS FOR ENTERING NAMES AND SPECIAL CHARACTERS

Refer to the letters on the number keys to select the desired characters. With each press of a number key (- ), the displayed character appears in the following order: upper case letters first, lower case letters next and finally the number corresponding to the key.

Number of times key is pressed

[ 26 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 27

If you make a mistake while entering a name

Use or to move the cursor to the incorrect character. Press /del to erase the wrong character and then enter the correct character.

To delete all characters, press and hold /del.

For example, to enter Movies:

1)When the phone is in standby mode, press phonebook.

2)Press , Store/Edit Name appears.

3)Press 6 once, and then press to move the cursor to the right.

4)Press 6 six times.

5)Press 8 six times.

6)Press 4 six times.

7)Press 3 five times.

8)Press 7 eight times.

9)When finished, press .

To continue to store the telephone number, proceed to step 5 on page 24.

If the next character uses the same number key, you must press to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.

[ 27 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 28

During a call, don???t press or the call will be disconnected.

[ 28 ]

VIEWING THE PHONEBOOK

Your phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use.

You can also use letters on the number keys to select the first letter of the desired name. Press a number key (2-9 and 0) once for the first letter, press twice for the second letter, and so on. The first location that begins with the letter you

entered appears.

For example, to search for ???Movies,??? press 6 once. Press /vol/ or /vol/, until the phonebook location is displayed.

3) To finish the viewing operation, press (or phonebook during a call).

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 29

MAKING CALLS USING THE PHONEBOOK

From Standby Mode

1)When the phone is in standby mode, view the phonebook location to dial (see ???Viewing the Phonebook??? on page 28).

2)Press or speaker. The displayed number is dialed.

3)To hang up press .

Movies

0295979035 Beethoven9/SPD1

From Talk Mode

1)Press or speaker.

2)View the phonebook location to dial (see ???Viewing the Phonebook??? on page 28).

3)Press . The number in the displayed phonebook location is dialed.

4)To hang up press .

SPEED DIALING

If you store a phone number in a speed dial memory location (10 locations:SPD1 - SPD0), you can use the speed dialing feature. When the phone is in standby mode, press and hold a number key (- ) associated with the speed dial until the phone number appears, then press or speaker. The number stored in speed dial (SPD1 - SPD0) is dialed.

[ 29 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 30

EDITING OR ERASING A STORED NAME, PHONE

NUMBER, DISTINCTIVE RING, AND SPEED DIAL

1)When the phone is in standby mode, press phonebook.

2)Press /vol/ or /vol/, or the number keypad to view the phonebook locations (see ???Viewing the Phonebook??? on page 28).

a. Editing the Stored Data

Phonebook :100

Search [A-Z/ / ]

Store [SELECT]

1)When the phonebook location to be edited appears, press . Store/Edit Name appears.

2)Follow the steps 3 to 7 under ???Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial??? on page 24 to complete the editing operation.

3)Press . You will hear a confirmation tone.

b. Deleting the Stored Data

1)When the phonebook location to be deleted appears, press /del.

Delete Memory? appears.

2)Press /vol/ or /vol/ to move the pointer to Yes.

3)Press . You hear a confirmation tone.

Deleted! appears in the display.

Store/Edit Name

Movies

Delete Memory?

Yes

No

[ 30 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 31

CHAIN DIALING

The memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing.

An example of this is a bank account number. Store the account or special number in one of the phonebook locations. (Refer to ???Storing Phone Numbers, Names, Distinctive Rings and Speed Dial??? on page 24). When you call your bank and you are prompted to enter the account number, scroll through your phonebook locations until you find your account number, and then press .

[ 31 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 32

???If you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear.

???When the call is

received via a telephoneCALLERcompany that does not offer Caller ID service, the caller???s phone number and name does not appear. (This includes some international calls.)

???When the call is via a private branch exchange (PBX), the caller???s phone number and name may

not appear.

ID

[ 32 ]

CALLER ID

You must subscribe to Caller ID services through your local telephone provider to use these features.

When the telephone rings, the Caller ID feature allows you to view the caller???s name, and phone number along with the date and time of call. Additionally, you can dial a number stored in the Caller ID list or save data to your Phonebook locations.

Important:

Memory locations for Caller ID messages and Phonebook locations (including Speed Dials) are common, you can store up to 100 in total (up to 50 locations). A Caller ID message is not stored when you have stored 100 of the phonebook locations. The earliest Caller ID message is overwritten when you have stored 100 of the phonebook locations and Caller ID messages in total (up to 50 locations).

1)When the Caller ID message is received, the display shows the caller???s phone number along with the date and time. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller???s name, the name will appear in the

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 33

2)When you pick up the phone, the display changes to Talk. (AutoTalk feature is set to on).

Data errors appear as ??? ???.

VIEWING THE CALLER ID LIST

The Caller ID list stores information for incoming calls - even unanswered calls. You can store 100 of the Caller ID messages (up to 50 locations) and Phonebook

locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in standby mode.

1)Press .

The summary screen appears. The screen shows the number of new messages and total messages.

2)To view the Caller ID messages in historical order (from new to old or from old to

To view the Caller ID messages with alphabetical search, press the number key pad (2-9 and 0) with the letter associated with the first letter of the desired message.

Once you view the Caller ID list with alphabetical search, you cannot switch back to historical order (from new to old or from old to new) unless you exit and re-enter the operation.

3) To finish the viewing operation, press (or during a call).

???The number of calls from the same Caller ID appears next to the received time. Once you view the new message, the number will be cleared and disappear.

???During a call, don???t press end or the call will be disconnected.

[ 33 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 34

DELETING A CALLER ID MESSAGE

Deleting Information from the Caller ID List

1)When the phone is in standby mode, view the Caller ID information to be deleted (see ???Viewing the Caller ID List??? on page 33).

2)Press /del. Delete Caller ID appears.

3) Press /vol/ or /vol/ to choose Yes.

4) Press . You will hear a confirmation tone.

Delete Caller ID

Yes

No

Deleting all Caller ID names/numbers

1) When the phone is in standby mode, press call id.

Caller ID

New : 5

Total: 25

[ 34 ]

2)Press /del. Delete All? appears.

3)Press /vol/ or /vol/ to choose Yes.

4)Press . You will hear a confirmation tone.

Delete All?

Yes

No

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 35

USING THE CALLER ID MESSAGE LIST

Calling a party from the Caller ID list

From Standby mode

1)When the phone is in standby mode, view the Caller ID message (see ???Viewing the Caller ID List??? on page 33).

2)Press or speaker. The displayed phone number dials automatically.

From Talk mode

1) Press or speaker.

21/12 11:20AM Jane Smith 0295979035

2)View the Caller ID message you want to dial (see ???Viewing the Caller ID List??? on page 33).

3)Press . The displayed phone number will be dialed.

Adding Zero to Caller ID message (New Zealand only)

While you review Caller ID information while the Insert Zero option is set to On, ???0??? is inserted. Refer to page 14 ???Insert Zero (New Zealand only)??? to set the Insert Zero option to On or Off. New Zealand Telecom customers should leave Insert Zero to On. Other New Zealand companies may require Insert Zero set to Off.

Storing Caller ID messages in the Phonebook

Messages shown in the Caller ID list can be stored in the phonebook. The phone number and name of the party on the Caller ID list can be stored in memory.

1)When the phone is in standby mode, view the Caller ID message to be stored. Then press . Store/Edit Name appears.

2)To complete the setting, follow the steps 4-8 in ???Storing Phone Numbers, Names, Distinctive Rings, and Speed dial??? on page 24.

[ 35 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 36

INFORMATIONADDITIONAL [ 36 ]

CHANGING THE DIGITAL SECURITY CODE

The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code.

To change the digital security code:

1.Perform the ???System Reset??? menu options (???De-register the Handset??? and ???Replacing the Base Settingf???) or the handset (see page 15).

2.To register the handset do the following steps:

1)Place the handset in the base.

2)Registration starts automatically.

While registering Handset Registering appears in the display.

3)When the registration is complete, Registration Complete appears in the display.

If the registration fails, Registration Failed appears in the display. Try the steps above again.

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 37

TROUBLESHOOTING

If your phone is not performing to your expectations, please try these simple steps first.

[ 37 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 38

[ 38 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 39

INDEX

[ 39 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 40

WARRANTY

One Year Limited Warranty

Important: Evidence of original purchase is required for warranty service.

Warrantor:Uniden Australia Pty Limited A.B.N. 58 001 865 498 Uniden New Zealand Limited

ELEMENT OF WARRANTY: Uniden warrants to the original retail owner for the duration of this warranty, its WDECT2300 (herein after referred to as the Product), to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. Warranty is only valid in the original country of purchase.

WARRANTY DURATION: This warranty to the original retail owner only, shall terminate and be of no further effect 12 months after the date of original retail sale. This warranty will be deemed invalid if the product is;

(A)Damaged or not maintained as reasonable and necessary,

(B)Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,

(C)Improperly installed,

(D)Repaired by someone other than an authorized Uniden Repair Agent for a defect or malfunction covered by this warranty,

(E)Used in conjunction with any equipment or parts or as part of a system not manufactured by Uniden.

PARTS COVERED: This warranty covers for one (1) year, the Base unit and handset. All accessories (AC Adapter etc)are covered for 90 days only.

STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, the warrantor at its discretion, will repair the defect or replace the product and return it to you without charge for parts or service. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN ADDITION TO AND DOES NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE

CONSUMER GUARANTEE ACT.

PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY: In the event that the product does not conform to this warranty, the Product should be shipped or delivered, freight pre-paid, with evidence of original purchase (eg. a copy of the sales docket), to the warrantor at:

Customers in other States should ship or deliver the Product freight pre-paid to their nearest Uniden Authorized Repair Centre (Contact Uniden for the nearest Warranty Agent to you).

[ 40 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 41

MEMO

[ 41 ]

UP349BH (WDECT2300) ENG OM 5/12/04 10:54 AM Page 42

?? Uniden Australia Pty Limited

Uniden New Zealand Limited

Printed in China

UPZZ01349BZ