INSTALLATION MANUAL

PAM-200

Universal Projector Mount

Sony Electronics

16540 West Bernardo Drive

San Diego, CA 92127

www.sony.com

IN-PAM200.R0

PAM-200

PAM-200

Parts List

NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Sony Electronics (800) 222-7669.

NOTE: Please review all WARNING and CAUTION statements (see Page 8) before beginning the installation of the PAM-200.

PAM-200 (Qty 1)

M4 x 10mm

Security Screw

(Qty 3)

M4 x 16mm

Security Screw

(Qty 3)

Installation Tools

Phillips Head Screw Driver Soft Material/ Blanket Tape Measure

Ladder

M3 Security Allen Wrench (Supplied)

????? Wood Drill Bit ??? Ceiling Installation (Commercially Available)

#14 X 2??? Wood

Screw (Qty 3)

Nylon Spacers (Qty 3)

M4 x 12mm

Security Screw

(Qty 2)

M4 External

Washer (Qty 2)

Portable Drill

Pencil

Stud Finder (Commercially Available)

M5 Security Allen Wrench (Supplied)

Masonry Bit (Commercially Available)

5/16??? Masonry Drill Bit ??? Concrete Installation

(Commercially Available)

PAM-200

Features

Congratulations on the purchase of your new Sony Electronics PAM-200 Projector Mount. The projector mount can be configured for ceiling installations. The PAM-200 features MagnaGuide??? Technology which assists the installer for quicker installation times and peace of mind. The PAM-200 Projector Mount is height adjustable from 9??? to 12??? to help achieve the perfect viewing height.

ASolid Structure Mounting Points

BSingle Wooden Stud Mounting Points

CCeiling Plate

DM6 x 20mm Security Screw

EAdjustable Suspension Neck

FMagnaGuide??? - Upper Assembly

GM4 x 12mm Security Screw and Star Washer

HLocking Tab

IMounting Hardware

JMagnets

KMagnaGuide???-Lower Assembly

LRadial Glide??? Set Screw

MProjector Plate

Optional Mounting Hardware

NM4 x 12mm Security Head Screw

ONylon Spacer

Selecting the Proper Mounting Hardware

1.Invert the projector and locate the mounting points.

2.Test each size of the screws provided.

3.The correct screws should thread easily into the mounting point and not pull out when pressure is applied.

WARNING: DO NOT OVERTIGHTEN YOUR MOUNTING SCREWS TO THE PROJECTOR CHASIS.

USING THE INCORRECT SCREW DEPTH MAY CAUSE DAMAGE TO YOUR

PROJECTOR.

PAM-200

Attaching the Mount

Unpack the PAM-200 and review any WARNING statements that apply to the installation. Select the desired location for the PAM-200.

M5 Allen Wrench

M4 x 10mm Security Head

Screw

Optional Hardware

When mounting the PAM-200 to a Sony projector, it is imperative that the projector plate not cover any access plates that allow the user to access the interior of the projector. The following steps will allow the user to mount the PAM-200 projector bracket to the Sony projector without fear of blocking any ventilation access plates.

Nylon Spacer

M5 Allen Wrench

M4 x 16mm Security Head

Screw

Nylon Spacer

1.Locate the mounting points on the bottom of the projector (see arrows above for mounting point recognition).

2.Place the nylon spacers over the mounting points.

3.Line up the mounting holes of the PAM-200 with the nylon spacer mounting holes.

4.Use three (3) M4 x 16mm security head screws to attach the PAM-200 to the projector.

5.Tighten the security head screws down with a M5 Security Allen wrench (supplied).

6.Do not overtighten these screws, as the threaded inserts can be damaged.

PAM-200

Ceiling Installation

1. Mounting Surfaces

NOTE: Use a 1/4??? drill bit to pre-drill the mounting holes before securing the wood screws (supplied).

Wood studs:Where denoted with the letter ???A???, mark these locations for wood stud installation.

NOTE: Use a masonry bit to pre-drill the mounting holes in the concrete surface.

Concrete surface: Where denoted with the letter ???B???, mark these locations for concrete installation.

2.Use two (2) #14 x 2??? wood screws (supplied) to attach the

ceiling plate to the wooden ceiling stud.

NOTE: For extra security, attach a third wood screw to the middle mounting point (A).

3.Slowly raise the projector toward the upper assembly. Once the projector is close to the upper assembly, MagnaGuide Technology will pull the lower assembly into the upper

assembly and the locking tab will engage.

WARNING: THE MAGNETS ARE USED FOR GUIDING

THE UNIT ONLY! PLEASE MAKE SURE

THE TWO (2) M4 X 12MM SCREWS ARE

USED TO SECURE THE PROJECTOR.

4.Attach the two (2) M4 x 12mm security screws and

washers that are located on each side of the locking tab. NOTE: Do not release your hold on the projector until the

upper and lower assemblies are engaged and the locking tab is in place.

NOTE: If you choose to use the center mounting point for added security, detach the adjustable suspension neck by removing the two (2) M6 x 12mm security screws, drive the wood screw in place and reattach the adjustable suspension neck and security screws.

After the projector has been installed, the projector must then be adjusted. To adjust the projector:

1.Loosen the M5 set screw using the M5 Allen wrench (both sides).

2.Adjust the projector to the correct position. Firmly grasp the projector in both hands, and tilt either forward or backward to adjust the level.

-OR-

Firmly grasp the projector in both hands and rotate side to side for orientation adjustment.

3.Tighten the M5 set screw on both sides using the M5 Allen wrench.

M5 Allen

Wrench

M4 x 12mm Security

Screw and Star Washer

M5 Set Screw

Height Adjustment

1.To adjust the height of the PAM-200, hold the weight of the projector and loosen the two (2) M6 x 12mm security screws.

2.Slide the adjustable suspension neck into the desired position.

3.Retighten the two (2) M6 x 20mm security screws.

NOTE: Do not release the projector until the M6 screws are completely tight.

M6 x 20mm

Security Screws

PAM-200

Safety Warning

M4 x 12mm

Security Screw

WARNING: Both M4 x 12mm security screws (located on each side of the mount) must be tightened securely before installation is complete. If the M4 x 12mm screws are not properly secured, there will be an increased risk of attachment failure, which could result in damage to the projector.

Concrete Mounting

NOTE: The PAM-200 can be mounted to a ceiling with a minimum 6??? thickness. Concrete wedge anchors must be used for concrete installation. It is recommended that ????? wedge anchors be used. A 5/16??? masonry bit must be used to drill the pilot hole. These items can be purchased at your local hardware store.

1.Begin by placing the ceiling plate into position against the ceiling, keeping it level.

2.Mark off four holes to be used for securing the mount and place the ceiling plate aside.

3.Next, drill holes using the appropriate masonry bit for your anchor.

4.Insert a concrete anchor into each hole.

5.If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the ceiling.

6.Once all of the anchors are in place, move the ceiling plate back into position.

7.Attach the nut onto the threaded shaft that is protruding from the ceiling.

8.Do not tighten until all nuts are in place.

Technical Specifications

All measurements are inches (mm).

PAM-200

Warranty

Limited Lifetime Warranty

All Sony products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Sony is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Any modification to the existing mount will void the manufacturers??? warranty.

DISCLAIMER OF WARRANTY.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Contact Sony Electronics

In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation.

Customer Service ??? (800) 222-7669

Warning Statements

WARNING: SONY DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY SONY PRODUCT FOR PURPOSES

OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS

OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR

CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING

TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.

WARNING: THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING 25LBS. IF NOT, THE CEILING STRUCTURE MUST

BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN

THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS

PERSONAL INJURY, OR EVEN DEATH.

WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE

PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.

WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND

COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL

INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE

LOCATION FOR FUTURE REFERENCE.

Indicates that the power plug is to be disconnected from the power outlet.

Safety precautions must be taken at all times.

Warning and Caution statements.

Contact Sony with any questions ??? (800) 222-7669.

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the projector and/or damage to the mounting surface.

Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the projector and could increase the risk of fire.

A qualified person should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the projector

Sony Electronics

16540 West Bernardo Drive

San Diego, CA 92127

www.sony.com

IN-PAM200.R0