WARNING / CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the

presence of uninsulated ???dangerous voltage??? within the product???s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system installer???s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi- tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device).

Any changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user???s authority to operate this product

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

1Do not use this apparatus near water.

2Clean only with dry cloth.

Do not block any ventilation openings. Install in

3accordance with the manufacturer???s instructions.

Do not install near any heat sources such as

4radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

5Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

6Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

7Only use attachments/accessories specified by the manufacturer.

8Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com- bination to avoid injury from tip-over.

9Unplug this apparatus during lighting storms or when unused for long periods of time.

10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.

SAFETY INSTRUCTIONS

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do 16 not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g.

on shelves above the unit).

17 GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out- let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

18 DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The plug must remain readily operable.

19 As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH. (Some models)

20 ANTENNAS

Outdoor antenna grounding

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of over- head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis- charge unit, connection to grounding electrodes and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

power cord contact an authorized service center.

25 Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.

26 Keep the product away from direct sunlight.

CONTENTS

WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PREPARATION

To view the extended version of owner???s manual . . 5

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cable Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Securing the TV to the wall to prevent falling

When the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WATCHING TV

Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Favorite channel setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Favorite channel list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Child Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.

Manufactured under license from Dolby Laboratories. ???Dolby ???and the double-D symbol are trademarks of Dolby Laboratories.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."

PREPARATION

*

MENU

FREEZE RATIO

FAV

VOL

ENTER

RETURN

*Wipe spots on the exterior only with the polishing cloth.

*Do not wipe roughly when removing

Polishing Cloth stain. Excessive pressure may cause scratch or discoloration.

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.

FRONT PANEL INFORMATION

??? Image shown may differ from your TV.

CAUTION

G When the TV cannot be turned on with the remote control, press the (power) button on the TV. (The remote control will not work when the (power) button on the TV is switched off. )

Remote Control Sensor

Power/Standby Indicator

Illuminates red in standby mode.

Illuminates blue when the TV is switched on.

PREPARATION

PREPARATION

BACK PANEL INFORMATION

COMPONENT IN

5

3

ANTENNA/

CABLE IN

4

1HDMI IN, HDMI/DVI IN

Digital Connection. Supports HD video and Digital audio. Doesn???t support 480i.

Accepts DVI video using an adapter or HDMI to DVI cable (not included).

2OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and home theater systems.

Note: In standby mode, this port doesn???t work.

3COMPONENT IN

Analog Connection. Supports HD.

Uses a red, green, and blue cable for video & red and white for audio.

4ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

5AV (Audio/Video) IN

Analog composite connection. Supports standard definition video only (480i).

6USB SERVICE ONLY, RS-232C IN (SERVICE ONLY)

Used for software updates.

7Power Cord Socket

For operation with AC power.

Caution: Never attempt to operate the TV on DC power.

STAND INSTRUCTION

??? Image shown may differ from your TV.

Installation

1Carefully place the TV screen side down on a cushioned surface to protect the screen from

damage.

Detachment

1Carefully place the TV screen side down on a cushioned surface to protect the screen from

damage.

PREPARATION

2Assemble the TV as shown.

2Loose the screws from the TV.

! NOTE

FRONT

GWhen assembling the stand, make sure to distinguish and assemble the front and rear side of the stand correctly.

G When assembling the desk type stand, check whether the screw is fully tightened. (If not tightened fully, the product can tilt forward after the product installation). If you tighten the screw with excessive force, the screw can deviate from abrasion of the tightening part of the screw.

Protection Cover

After removing the stand, install the included protection cover over the hole for the stand.

Press the PROTECTION COVER into the TV until you hear it click.

PREPARATION

4 inches

4 inches

CAUTION G

G

Ensure adequate ventilation by following the clearance recommendations. Do not mount near or above any type of heat source.

INFO

POWER

INPUT

1 2 3

INFO Displays channel information at the top of the screen.

Q.MENU Opens the list of Quick Menu options.

POWER Turns the TV on from standby or off to standby.

INPUT Rotates through inputs.

Also switches the TV on from standby.

POWER SAVING Adjusts the Power Saving level.

PREPARATION

4 5 6

7 8 9

0 FLASHBK

LIST

MUTE

P

VOL CH AG

E

ENTER

FREEZE RATIO

* FAV

Installing Batteries

NUMBER button

??? (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.

LIST Displays the channel list.

FLASHBK Tunes to the last channel viewed.

VOLUME UP Adjusts the volume.

/DOWN

MUTE Switch the sound on or off.

CHANNEL Changes the channel.

UP/DOWN

PAGE Moves from one full set of screen information to the next

UP/DOWN one.

THUMBSTICK Navigates the on-screen menus and adjusts the system

(Up/Down/LeftRight/ENTER) settings to your preference.

MENU Displays the main menu or clears all on-screen displays and returns to TV viewing.

RETURN Allows the user to move return one step in an interactive application or other user interaction function.

Blue button have channel edit and channel block function. Color button The other has no function.

* Not functional.

FREEZE Freezes the current frame.

RATIO Changes the aspect ratio of the video.

FAV Scroll through the programmed Favorite channels.

???Open the battery compartment cover on the back side and install the batteries matching correct polarity.

???Install two 1.5V AAA batteries. Don???t mix old or used batter- ies with new ones.

???Close cover.

PREPARATION

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. Zenith recommends that wall mounting be performed by a qualified professional installer.

! NOTE

G Screw length needed depends on the wall mount used. For further information, refer to the instruc- tions included with the mount.

G Standard dimensions for wall mount kits are shown in the table.

G When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.

G Do not use screws longer then the standard dimen- sion, as they may cause damage to the inside to the TV.

G For wall mounts that do not comply with the VESA standard screw specifications, the length of the

screws may differ depending on their specifica- tions.

G Do not use screws that do not comply with the VESA standard screw specifications.

Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. Zenith is not liable for these kinds of accidents.

GZenith is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa- tion instructions.

SECURING THE TV TO THE WALL TO PREVENT FALLING

WHEN THE TV IS USED ON A STAND

???You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

???Image shown may differ from your TV.

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product.

Caution: Please make sure that children don???t climb on or hang from the TV.

???Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

??? Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

PREPARATION

PREPARATION

???To prevent damage do not connect to the power outlet until all connections are made between the devices.

???Image shown may differ from your TV.

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connection.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

ANTENNA/

Cable TV

Wall Jack

CABLE IN

EXTERNAL EQUIPMENT SETUP

???To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

???Image shown may differ from your TV.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

Component Connection

2.How to use

???Turn on the digital set-top box.

SETUP EQUIPMENT EXTERNAL

EXTERNAL EQUIPMENT SETUP

DVD SETUP

Component Connection

1. How to connect

Select the Component1 or 2 input source on the TV using the INPUT button on the remote control.

??? Refer to the DVD player's manual for operating instructions.

ONLY SERVICE USB

COMPONENT IN

12

Y PBPRL R

HDMI Connection

1. How to connect

2No separate audio connection is necessary. HDMI supports both audio and video.

2.How to use

???Select the HDMI1 or 2 input source on the TV using the INPUT button on the remote control.

???Refer to the DVD player's manual for operating instructions.

IN

1

HDMI-DVD OUTPUT

VCR SETUP

Composite (RCA) Connection

1. How to connect

Connect the AUDIO/VIDEO jacks between TV and

1VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

2.How to use

???Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner???s manual.)

???Select the AV input source on the TV using the INPUT button on the remote control.

!NOTE

G If you have a mono VCR, connect the audio cable

from the VCR to the AUDIO L(MONO) jack of the TV.

ANT OUT OUTPUT

SWITCH

1

SETUP EQUIPMENT EXTERNAL

CHANNEL SETUP

Auto Scan (Auto Tuning)

Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

TV WATCHING

1

Select CHANNEL.

MENU

2

3

4

???The TV will ask for a password if parental control has been activated (LOCK Menu). Use the password you set up in the LOCK Menu to allow a channel search.

???When setting the Auto Tuning or Manual Tuning, the number of maxi- mum channels you can store is 900. It is subject to change depending on the broadcasting signal environment.

TV WATCHING

11 2 3

1

P

A

CH G

E

2

RETURN

Turn the pages.

Return to TV viewing.

INITIAL SETTING

This Function guides the user to easily set the essential items for viewing the TV for the first time when pur- chasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be acti- vated from the user menus.

???Default selection is ???Home Use???. We recommend setting the TV to ???Home Use??? mode for the best picture in your home environment.

??????Store Demo??? Mode is only intended for use in retail environments. Customers can adjust the ???Picture menu - Picture mode??? manually while inspecting the TV, but the TV will automatically return to preset in-

store mode after 5 minutes.

???You can also adjust Initial Setting in the OPTION menu. Factory defaults are set when you choose ???Home Use???.

???If you do not complete the Initial setting, it will appear whenever the TV is switched on until the Initial setting procedure is completed.

TV WATCHING

TV WATCHING

Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently.

???Aspect Ratio: Selects your desired picture format.

???Picture Mode: Selects the factory preset picture depend on the viewing environment.

???Sound Mode: Selects the factory preset sound for type of program.

???Caption: Select on or off.

???Multi Audio: Changes the audio language (Digital signal).

SAP: Selects MTS sound (Analog signal).

???Sleep Timer: Select the amount of time before your TV turns off automatically.

???Del/Add/Fav: Select channel you want to add/delete or add the channel to the Favorite List.

Q.MENU

Return to TV viewing.

LOCK

1

Display each menu.

MENU

2

3

CHANNEL

Auto Tuning

Manual Tuning

Channel Edit

4

Return to TV viewing.

MENU

PICTURE

E

Aspect Ratio

Power Saving

Picture Mode

Screen (RGB-PC)

???Select the desired picture format

???Reduces the TV???s power consumption.

???Select the Vivid, Standard, Cinema, Sport, Game, Expert1 or Expert2.

???Adjust the Contrast, Brightness, Sharpness, Color, Tint.

???Advanced Control: You can calibrate the screen for each Picture Mode or set the video value according to the special video screen.

???Expert Control: By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users.

???Reset: Settings of the selected picture modes return to the default factory settings.

???Adjust the screen Resolution, Auto config, Position, Size, Phase, Reset.

TV WATCHING

AUDIO

Auto Volume

Balance

Sound Mode

TV Speaker

???Makes sure that the volume level remains consis- tent whether you are watching a commercial or a regular TV program.

???Adjust the left/right sound of speaker to suit your taste and room situations.

???Select the Standard, Music, Cinema, Sport, and Game.

???SRS TruSurround XT, Treble, Bass: Adjust the sound to suit your taste and room situations.

???Reset: Settings of the selected Sound Mode return to the default factory settings.

???Turn the TV speaker On or off.

TIME

Sleep Timer : Off

??? Auto: The time is set automatically from a digital channel signal.

Select your viewing area time zone.

Clock Select Auto, Off, On depending on whether or not your viewing area observes Daylight Saving time.

??? Manual: Set the clock manually.

Off Time ??? Select On or Off.

On Time ??? Select On or Off.

Sleep Timer

??? Select the amount of time before your TV turns off automatically: Off, 10, 20, 30, 60, 90, 120, 180, 240.

Z42PQ20-U 9/21/09 2:51 PM Page 24

WATCHING TV

OPTION

TV WATCHING

LOCK

Menu Language

(Language)

Audio Language

Input Label

key Lock

Caption

ISM Method

Initial Setting

???Selects your desired language for on screen menus: English, Spanish, French.

???Sets a label to each input source.

???This feature can be used to prevent unauthorized viewing by locking out the front panel controls.

???When selecting Off, Submenus for Analog, DTV, and Digital Option become disabled.

???Analog: CC1 ~ CC4 , Text1 ~ Text4.

???Digital: CC1 ~ CC4 , Text1~ Text4, Service1~ Service6.

???Digital Option: Customize the DTV/CADTV cap- tions that appear on your screen.

???Use it to minimize any fixed image on the screen. : Normal, Orbiter, Color Wash, White Wash.

???After turning on the TV, adjust Language, Mode, Time, Auto Tuning.

Downloadable Rating

Input Block

Lock System

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Downloadable

Rating

Input Block

???Select On or Off.

???Change the password.

???Select a channel number that you wish to block.

???Blocks movies according to the movie ratings limits specified.

???Prevents children from watching certain children's TV programs, according to the ratings limit set.

???Based on the ratings, blocks certain TV programs that you and your family do not want to view.

???This function may become available in the future and will be available only for digital channel signal.

???Enables you to select a source to block from the external source devices you have hooked up.

Z42PQ20-U 9/21/09 2:51 PM Page 25

APPENDIX

TROUBLESHOOTING

Abnormal Operation

??? Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV.

WATCHING

Video Problems

No picture &No sound

??? Check whether the product is turned on.

??? Try another channel. The problem may be with the broadcast.

??? Is the power cord inserted into wall power outlet?

???Check your antenna direction and/or location.

???Test the wall power outlet, plug another product???s power cord into the outlet where the product???s power cord was plugged in.

TV

Picture appears slowly after switching on

No or poor color or poor picture

Horizontal/vertical bars or picture shaking

Poor reception on some channels

Lines or streaks in pictures

No picture when connecting HDMI

???This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes.

???Adjust Color in menu option.

???Keep a sufficient distance between the product and a VCR.

???Try another channel. The problem may be with the broadcast.

???Are the video cables installed properly?

???Activate any function to restore the brightness of the picture.

???Check for local interference such as an electrical appliance or power tool.

???Station or cable product experiencing problems, tune to another station.

???Station signal is weak, reorient antenna to receive weaker station.

???Check for sources of possible interference.

???Check antenna (Change the direction of the antenna).

???Check HDMI cable over version 1.3.

The HDMI cables don???t support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.

APPENDIX

Audio Problems

The signal is out of range

Vertical bar or stripe on

background &

Horizontal Noise &

Incorrect position

Screen color is unstable or single color

???Adjust resolution, horizontal frequency, or vertical frequency.

???Check the input source.

???Work the Auto configure or adjust size, phase, or H/V position. (Option)

???Check the signal cable.

???Reinstall the PC video card.

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV.

Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

1Here???s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it???s almost dry, and then use it to wipe the screen.

2Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the Cabinet

???To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

???Please be sure not to use a wet cloth.

Extended Absence

CAUTION

GIf you expect to leave your TV dormant for a long time (such as a vacation), it???s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

APPENDIX

TV WATCHING

WARRANTY PERIOD:

LABOR: ONE YEAR from the Date of Purchase.

PARTS: ONE YEAR from the Date of Purchase.

Effective Date of Warranty: Your warranty period Begins on the date of sale to the original consumer/end user. KEEP THE DEALER???S DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service.

Repair Parts and Replacement Units are warranted for the remaining period of the original warranty.

HOW SERVICE IS HANDLED:

In Home Service. Please Call the Zenith Interactive Center at 1-877-9ZENITH (1-877-993-6484) to schedule a service appointment.

Your unit will be repaired or replaced with a new, sub- stitute model or factory reconditioned unit, at Zenith???s option. If repaired, parts used in the repair may be new or remanufactured.

Visit our website at http://www.zenithservice.com

???damage caused in shipping or transit

???service required as a result of improper installation, including incorrect or insufficient AC supply (please consult the owner???s manual for power supply requirements)

???installation or repair of antenna systems, cable con- verters, cable company supplied equipment, or other components in a video system

???set-up or adjustment on consumer controls, or damage caused by improper adjustments

???damage caused by other system components

???any unit that has been modified or incorporated into any other product

???replacement of batteries on the remote control.

???damage (including cosmetic damage), failure, loss

or personal injury due to misuse, abuse, negli- gence, improper maintenance or storage, or to acts of nature or other causes beyond Zenith???s control. (Causes beyond Zenith???s control include but are not limited to lightning strike, power surges, power out- ages and water damage.)

???Image burn-in

???repair or replacement of warranted parts by other than Zenith Authorized Service Centers.

???units purchased or serviced outside of the U.S.A.

???product where the original factory serial numbers have been removed, defaced or changed in any way.

???product sold and labeled as ???as is, where is??? or sim- ilar disclaimer.

To obtain customer assistance, prod- uct information, or Dealer or Service locations

Call 1-877-9Zenith (1-877-993-6484) (24 hours a day, 365 days per year) and select appropriate options from the menu.

Or visit our website at http://www.zenithservice.com