User manual

BOSSCOM Bi1 controller installed in a Bang & Olufsen Beo4 remote control.

Operate these devices using the modied Beo4:

Samsung LED TV 7 -series and other.

Operate devices that are operate able with RCU???s like:

Samsung most remotes for Samsung digital TV.

Congratulations

With the BOSSCOM controller installed inside your Bang & Olufsen Beo4 remote control, you can fully operate your non B&O TV with this terminal. This guide explains how.

If your Beo4 has already been correctly set up, you can now proceed to one of the two operation tables:

Page 9

If your Beo4 has enabled Navi buttons . *1

Page 8

In any other case.

Important ! !

If the BOSSCOM controller has not yet been optimized for your setup, refer to the installation section about the initial setup and option program- ming. There is no programming needed during everyday use.

The BOSSCOM controller that has been installed inside your Beo4 remote control, can be used in any Beo4 remote control. Both rst generation mod- els and the latest with extra buttons for manoeuvring, the Beo4 Navi.

To get the most of your modied Beo4, the BOSSCOM controller must be programmed according to the Beo4 model and the environment that your TV is a part of. Refer to page 5 and forward, for the initial setting.

*1 Extra buttons have been added on never Beo4 models, Beo4 Navi. Se page 10.

The BOSSCOM controller for the Beo4 remote control

The BOSSCOM controller is a small microcomputer module, which is speci!cally made to be built in to a Bang & Olufsen Beo4 remote control.

The controller captures the commands that were meant for operating a Bang & Olufsen device. Before the commands are emitted from the Beo4, these commands are convert- ed, and therefore also able to operate a non Bang & Olufsen TV.

Each controller is dedicated for operating a speci!c product like an Apple iPod docking station, a #at screen TV, a curtain controller etc.

The controller makes the Beo4 able to operate a third part device, still able to operate any other Bang & Olufsen products.

If there is a Bang & Olufsen audiomaster in the room, it can be used for handling the sound. Speakers con- nected to an audiomaster are of a much better quality than the speakers in a TV. In a B&O linkroom setup with Beolink Active or Beolink Passive, you can also use these speakers to improve sound from most TV???s.

Only a simple audio cable is needed between the TV and the audiomaster. See the option programming sec- tion about AAUX and PC modes on page 11.

Operating with BOSSCOM .

To be able to operate the non B&O TV optimal using the BOSSCOM the user has to be familiar with the operations available when using the original remote control, as described in the TV???s user manual.

A beo4 remote control is not equipped with as many keys as most remote controls for non B&O devices. We have designed an operation ???layout??? that works logically, even

BOOSCOMcommon layout for mans to other functions.

The Beo4 Navi model introduces new buttons, making it easier to make operation table???s, closer to the TV???s own.

Coloured function buttons.

To make room for easy access to more important functions, in some layouts we have moved the coloured function buttons, to a lower layer. In these layouts to send a ???color??? command, amust be pressed before the coloured button itself.

This way we are able to assign other functions to the coloured buttons in direct mode. In a BOSSCOM environment the coloured buttons are often assigned to these opera-

tions:

Guide, EPG or similar.

Back, Backup, Return or similar.

Programme zapping. P+/ P- ,

Channel up/ down or CH+/ CH-.

Go, Navi or Stop shifted operation.

Some of the buttons has two or three operations. To get to these they have to be preced- ed withO or .

In case of Beo4 Navi a button has been a added to replace the button, when in ???mode 2???. In mode 2 the BOSSCOM uses the Center button for shifting, instead of

.. Refer to page 10.

Buttons that has been assigned secondary functions are listed in the operating table on page 9.

Programme stepping, up/ down manoeuvring in menus.

Most set top boxes and TV???s has 4 arrow buttons for manoeuvring in or screen menus, up, down, left and right. In addition they are equipped with separate programme step- ping buttons for zapping through the programme list. Often these keys are named P+, P -, CH+ or CH -.

BOSSCOM often makes use of the and the keys for programme zap- ping. This way the four up, down, left and right buttons are free to be used for the more natural use of manoeuvring in on screen menus.

Using a Beo4 Navi in mode 2, manoeuvring in On-screen menus is fully handled using the added ???joy-stick???, not available on previous Beo4 models. In a Beo4 Navi setup we therefore can make use of the up and down arrows for programme zapping.

Setting the Zap Mode Option

are used to manoeuvre up and down in an on-screen menu. This is the default factory setting, as described above.

Selecting the Zap mode buttons:

Enter one of these 2 codes within 10 seconds to set the pre"ered Programme Zap mode buttons.

Disabling and Dual TV Option

The BOSSCOM controller in the modi!ed Beo4 remote control can be enabled or disa- bled using this option. When disabled the Beo4 remote control operates as a Beo4 that has not been modi!ed.

In DUAL TV -mode the BOSSCOM controller enables operation of both a B&O TV and the non B&O TV which the controller is made to operate.

Disabling and Dual TV mode:

Enter one of these 3 codes within 10 seconds to set the pre"ered mode.

Disables the BOSSCOM controller.

Enables the BOSSCOM controller.

Enables the BOSSCOM controller in Dual TV mode.

In this mode:

starts operating a B&O TV. starts operating the non B&O TV

Translation table when NOT in Navigation mode.

* see page 10

Daily operation

Turns on the TV

Turns o! the TV

Enter

*1 The up/ down arrow operations can be ex- changed with the blue and yellow buttons. See page 6.

Text TV operation

Text TV on/ mix

Text TV o!

Playback operations

Play press 1 sec.

Stop

Pause

Rew/ FF

Record

Other operations

*2 As the direct function of the coloured func- tion buttons has been assigned to other func- tions, these have to be preceded with a

to retrieve the actual coloured function.

Green function

Yellow function

Red function

Blue function

Special/ alternative operations

Play Record 3D

AD

Translation table when IN Navigation mode.

* see page xxxxxx

Daily operation

Turns on the TV

Turns o! the TV

Enter

CH+ / CH -

REW / FF

Navi buttons are used for manoeuvring in on- screen menus.

Yellow key

Blue key

Green key

Red key

Exit

Back

Source

Menu TTV Index

EPG

CH List

PRE CH

TOOLS

Text TV operation

Text TV on/ mix

Text TV o!

Playback operations

Play

Stop

Pause

Record

Other operations

Special/ alternative operations

Record 3D

AD

Beo4 NAVI mode option.

Newer Beo4 models are named Beo4 Navi due to an added special navigation button. A joystick type control button, placed where previous Beo4 models have a button.

If your Beo4 has a button, this chapter is not relevant for you !

Use of the Beo4 Navi joystick navigation operation:

Enter one of these 2 codes within 10 seconds to enable or disable the BOSSCOM controllers use of the ex-

Set the Beo4 Navi remote control in operation mode 2, as described in the B&O user guide that was sup- plied with your Beo4, if you want to use these. Otherwise select mode 1.

Enable use of the NAVI control.

When the BOSSCOM controller NAVI mode has been enabled, use the operation table on page 9.

Disable use of the NAVI control.

When the BOSSCOM controller NAVI mode has been disabled, use the operation table on page 8.

When the TV mode is selected by pressing the button, it automatically powers on the TV and turns on the picture.

But often the sound is lead to external speakers at-

This option set the way that the BOSSCOM handles volume in TV mode.

This option also can power on other B&O devices than the TV, when is selected. Audio is then typically fed from the TV to the audiomaster from using a Line to Datalink cable. Moving the TV sound

proves the sound quality.

The Beo4 VMEM / VTAPE button option

On your BOSSCOM modi!ed Beo4 remote control, the VMEM button can be pro- grammed, to open a speci!c source on your non B&O TV.

VMEM/ VTAPE options

Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected with the VMEM or VTAPE button.

No new source selected.

The AV1 socket on the TV is opened.

The AV2 socket on the TV is opened.

The DTV tuner on the TV is opened.

The Component 1 socket is shifted to.

The Component 1 socket is accessed.

The HDMI 1 socket is accessed.

The HDMI 2 socket is accessed.

S-VHS 1

USB Wiselink

As the BOSSCOM controller is able to operate many di"erent TV models, there might be some sources in the table, that is not available on your TV. The only way to #nd out if your TV accepts these codes, is testing each of the options.

If a source is not access able using these options, sources must be accessed the same way as using the TVs original remote control. Using the source button.

The Beo4 DTV/ SAT button option

On your BOSSCOM modi!ed Beo4 remote control, the DTV/ SAT button can be pro- grammed, to open a speci!c source on your non B&O TV.

DTV/ SAT options

Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected with the DTV/ SAT button.

No new source selected.

The AV1 socket on the TV is opened.

The AV2 socket on the TV is opened.

The DTV tuner on the TV is opened.

The Component 1 socket is shifted to.

The Component 1 socket is accessed.

The HDMI 1 socket is accessed.

The HDMI 2 socket is accessed.

S-VHS 1

USB Wiselink

As the BOSSCOM controller is able to operate many di"erent TV models, there might be some sources in the table, that is not available on your TV. The only way to #nd out if your TV accepts these codes, is testing each of the options.

If a source is not access able using these options, sources must be accessed the same way as using the TVs original remote control. Using the source button.

The Beo4 DVD button option

On your BOSSCOM modi!ed Beo4 remote control, the DVD button can be pro- grammed, to open a speci!c source on your non B&O TV.

DVD options

Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected with the VMEM or VTAPE button.

No new source selected.

The AV1 socket on the TV is opened.

The AV2 socket on the TV is opened.

The DTV tuner on the TV is opened.

The Component 1 socket is shifted to.

The Component 1 socket is accessed.

The HDMI 1 socket is accessed.

The HDMI 2 socket is accessed.

S-VHS 1

USB Wiselink

As the BOSSCOM controller is able to operate many di"erent TV models, there might be some sources in the table, that is not available on your TV. The only way to #nd out if your TV accepts these codes, is testing each of the options.

If a source is not access able using these options, sources must be accessed the same way as using the TVs original remote control. Using the source button.

The Beo4 VAUX button option

On your BOSSCOM modi!ed Beo4 remote control, the VAUX button in the List - menu can be programmed, to open a speci!c source on your non B&O TV.

VAUX options

Enter one of these codes within 10 seconds, to select the source on the non B&O TV that will be selected with the VMEM or VTAPE button.

No new source selected.

The AV1 socket on the TV is opened.

The AV2 socket on the TV is opened.

The DTV tuner on the TV is opened.

The Component 1 socket is shifted to.

The Component 1 socket is accessed.

The HDMI 1 socket is accessed.

The HDMI 2 socket is accessed.

S-VHS 1

USB Wiselink

As the BOSSCOM controller is able to operate many di"erent TV models, there might be some sources in the table, that is not available on your TV. The only way to #nd out if your TV accepts these codes, is testing each of the options.

If a source is not access able using these options, sources must be accessed the same way as using the TVs original remote control. Using the source button.