Getting Started

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE THE COVER(OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates ???dangerous voltage??? inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

CAUTION : DVD RECORDER USES AN INVISIBLE

LASER BEAM WHICH CAN CAUSE

HAZARDOUS RADIATION EXPOSURE

IF DIRECTED.

BE SURE TO OPERATE RECORDER

CORRECTLY AS INSTRUCTED.

CAUTION

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

This product satisfies CE regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is

required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a

power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the

plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non- commercial use by end-user consumers for licensed contents.

No rights are granted for commercial use.

The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Precaution

Important Safety Instructions

Read these operating instructions carefully before using the DVD Recorder. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding- type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions

???Before connecting other components to this DVD Recorder, be sure to turn them all off.

???Do not move the DVD Recorder while a disc is being played, or the disc may be scratched or broken, the DVD Recorder's internal parts may be damaged.

???Do not put a flower vase filled with water or any small metal objects on the DVD Recorder.

???Be careful not to put your hand into the disc tray.

???Do not place anything other than the disc in the disc tray.

???Exterior interference such as lightning and static electricity can affect normal operation of this DVD Recorder. If this occurs, turn the DVD Recorder off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet.

The DVD Recorder will operate normally.

???Be sure to remove the disc and turn off the DVD Recorder after use.

???Disconnect the AC power cord from the AC outlet when you don???t intend to use the DVD Recorder for long periods of time.

???Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

???Do not use benzene, thinner, or other solvents for cleaning.

???Wipe the cabinet with a soft cloth.

Disc Handling

??? Use discs with regular shapes. If an irregular disc

(a disc with a special shape) is used, this DVD recorder may be damaged.

Holding discs

??? Avoid touching the surface of a disc where recording is performed.

DVD-RW, DVD-R

??? Clean with an optional DVD- RAM/PD disc cleaner (LF- K200DCA1 where available). Do not use cleaners or cloths for CDs to clean DVD-RW/ DVD-R discs.

DVD-Video, Audio CD

???Wipe off dirt or contamination on the disc with a soft cloth.

Cautions on handling discs

???Do not write on the printed side with a ball-point pen or pencil.

???Do not use record cleaning sprays or antistatic. Also, do not use volatile chemicals, such as benzene or thinner.

???Do not apply labels or stickers to discs. (Do not use discs fixed with exposed tape adhesive or leftover peeled-off stickers.)

???Do not use scratch-proof protectors or covers.

???Do not use discs printed with label printers available on the market.

???Do not load warped or cracked discs.

Started ettingG

Getting Started

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

???Do not keep under direct sunlight.

???Keep in a cool ventilated area.

???Store vertically.

???Keep in a clean protection jacket.

???If you move your DVD recorder suddenly from a cold place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.

Disc Specifications

DVD-Video

???A digital versatile disc (DVD) can contain up to 135-minutes of images, 8 audio languages and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre quality images in the comfort of your own home.

???When switching from the first layer to the second layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound.

This is not a malfunction of the DVD Recorder.

???Once a DVD-R/-RW recorded in Video Mode is finalised, it becomes DVD-Video.

Audio CD

???An audio disc on which 44.1kHz PCM Audio is recorded

???Plays CD-DA format audio CD-R and CD-RW discs. The DVD Recorder may not be able to play some CD-R or CD-RW discs due to the condition of the recording.

CD-R/-RW

MP3 CD-R/-RW

???Only CD-R discs with MP3 files recorded with ISO9660 or JOLIET format can be played back

???Only MP3 files with the ".mp3", ".MP3" extension can be used.

???For MP3 files recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

???Playable bitrate range is from 56Kbps to 320Kbps.

???This DVD Recorder can handle a maximum of 500 files and 100 folders.

JPEG CD-R/-RW

???Only JPEG files with the ".jpg", ".JPG" extension can be used.

???This DVD Recorder can handle a maximum of 500 files and 100 folders.

???Maximum size of progressive JPEG is 3M pixels.

???MOTION JPEG is not supported.

Using CD-R/-RW

???Use a 700MB(80 minutes) CD-R/-RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.

???If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, all recorded files may not play.

???Some CD-R/-RW discs may not be playable with this DVD Recorder, depending on the device which was used to burn them. For contents recorded on CD-R/- RW media from CDs for your personal use, playability may vary depending on contents and discs.

Using MPEG4 disc

???Disc : CD-R/-RW, DVD-R/-RW

???MPEG4 File with following extensions can be played. : .avi, .divx, .AVI, .DIVX

???MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x DivX-Pro Xvid

???Motion Compensation : QPEL, GMC

???four CC : MPG4, mpg4, DIV3, divX3, DIVX, divX, DX50, MP43, mp43, XVID, xvid

???Available Audio Format : ???MP3???, ???MPEG1 Audio Layer2???, ???LPCM???, ???AC3???, ???DTS???, ???MS ADPCM???

???Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass

DVD-R Disc Playback and Recording

???Once a DVD-R recorded in Video Mode is finalised, it becomes DVD-Video.

???You can record onto the available space on the disc and perform editing functions such as giving titles to discs and programmes and erasing programmes before finalising.

???When programming is erased from a DVD-R, that space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

???It takes about 30 seconds for the DVD Recorder to complete recording management information after recording finishes.

???This DVD Recorder optimizes the DVD-R for each recording. Optimizing is carried out when you start recording after inserting the disc or turning on the DVD Recorder. Recording onto the disc may become impossible if optimizing is carried out too many times.

???Playback may be impossible in some cases due to the condition of recording.

???This DVD Recorder can play back DVD-R discs recorded and finalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

DVD-RW Disc Playback and Recording

???Recording and playback can be performed on DVD- RW discs in both the Video and VR Modes.

???Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform addtional recording.

???Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video.

???In both modes, playback can be performed before and after finalisation, but additional recording, deleting and editing can not be performed after finalisation.

???If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format.

Be careful when executing Format because all the recorded data may be lost.

???A DVD-RW blank disc is initialized to VR Mode when first initialized.

???DVD-RW (VR mode)

-This is a format that is used for recording data on a DVD-RW disc. You can record multiple titles, edit, delete, partial delete, create a playlist, etc.

-A disc that is recorded in this mode may not be played by existing DVD Recorder.

???DVD-RW (Video mode)

-This is a format that is used for recording data on a DVD-RW or DVD-R disc. The disc can be played by existing DVD Recorder once it has been finalised.

-If a disc that has been recorded in Video Mode by a different maker???s recorder but has not been finalised, it cannot be played or additionally be recorded by this DVD Recorder.

COPY PROTECTION

???Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD recorder directly to your TV, not to a VCR.

Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

???This DVD Recorder incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

Protection

This DVD Recorder can allow you to protect the contents of your discs, as described below.

???Programme-protected: See page 70 ???Locking(Protecting) a Title???

???Disc-protected: See page 82 ???Disc Protection???

???DVD-RW/DVD-R discs that are incompatible with the DVD-VIDEO format cannot be played with this DVD Recorder.

???For more information on DVD recording compatibility, consult your DVD-RW/DVD-R manufacturer.

???Use of poor quality DVD-RW/DVD-R discs may cause following unexpected problems including, without limitation, recording failure, loss of recorded or edited materials or damage to the DVD Recorder.

Do not use the following discs!

???LD, CD-G, CD-I, Video-CD, CD-ROM, and DVD-ROM discs should not be used in this DVD Recorder. [Note]

Disc types that can be played : CD/CD-R/CD-RW/ MP3/JPEG/MPEG4/DVD-Video/DVD-RW/DVD-R. For a DVD-R/DVD-RW disc, which has been recorded in Video Mode on another component, it can play only when finalised.

???Some commercial discs and DVD discs purchased outside your region may not be playable with this DVD Recorder. When these discs are played, either ???No Disc??? or "Please check the regional code." will be displayed.

???If your DVD-RW disc is an illegal copy or is not in DVD video format, it may also not be playable.

Disc Compatibility

???High Speed Recording discs can be used in this DVD Recorder.

???Not all brands of discs will be compatible with this DVD Recorder.

Started ettingG

Getting Started

Contents

Started ettingG

Getting Started

General Features

The DVD Recorder allows you to record and play high quality digital video on DVD-RW/DVD-R discs. You can record and edit digital images on DVD-RW/DVD-R discs as if they were VCR tapes.

High quality digital audio and video recording and playback

Record up to 8-hours of images with a 4.7 GB DVD-RW/DVD-R disc, depending on the recording mode.

Selectable Recording Mode

You can set your recorder to one of four different recording speeds, each varying in recording quality and length. EP (6Hr or 8Hr) mode yields the most recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording.

Automated Quality Adjustment for Timer Recording

If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space.

(See page 46.)

Creating a DVD video title using

DVD-RW/DVD-R disc

With the DVD Recorder, you can create your own DVD Video titles on 4.7 GB DVD-RW/DVD-R discs.

Copying data from a digital camcorder using a DV input jack (DVD-R130, R131 only)

Record DV Device video onto DVD-RW, DVD-R discs using the DV input jack (IEEE 1394-4pin/4pin).

(See pages 43-44.)

High quality progressive scan

Progressive scanning provides high resolution and flicker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See pages 21, 35)

A variety of functions with an easy-to-use user interface

The integrated menu system and the messaging function allow you to perform desired operations both easily and conveniently. With a DVD-RW disc, you can edit recorded video, create a playlist, edit video in a specific sequence according to your requirements.

MPEG4 playback

This DVD Recorder can play MPEG4 formats within an avi file.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under licence.

Started ettingG

Make sure to check the following terms before reading the user???s manual.

Icons that will be used in manual

About the use of this user???s manual

1)Be sure to be familiar with Safety Instructions before using this DVD Recorder. (See pages 2-5)

2)If a problem occurs, check for Troubleshooting. (See pages 86-89.)

Copyright

??2006 Samsung Electronics Co.

All rights reserved; No part or whole of this user???s manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.

Step 1 Select the disc type

This DVD Recorder can record on the following types of discs.

If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW type disc.

If you want to save recording without any change, choose a non-rewritable DVD-R.

Step 2 Format the disc to start recording

Unlike a VCR, the DVD Recorder automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video format (Video mode) or DVD-Video Recording format (VR mode). For an unused disc, a message that asks whether to format in VR Mode or not is displayed. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing.

Using a DVD-R

Formatting a disc is unnecessary and only Video Mode Recording is supported. You can play this type of discs on various DVD components only when they have been finalised.

???You can only use either the VR or Video mode on a DVD-RW, but not

???You can change the DVD-RW format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats.

Getting Started

There are two different recording methods, Direct Recording and Timer Recording. Timer recording is classified as a Date : Once, Daily, MO-SA, MO-FR, W-SA, etc.

Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the recording mode. When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.

Step 4 Playing

You can select the title you want to play in a displayed menu and then immediately start playback.

A DVD consists of sections called titles, and sub sections called chapters.

During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalise recording on DVD-R / DVD-RW discs in Video mode.

The chapter???s length (interval between chapters) varies according to the recording mode.

Step 6 Finalising & Playing on other DVD components

To play your DVD on other DVD components, finalising may be necessary. First, finish all editing and recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

Although finalising is generally unnecessary when playing the disc on a VR Mode compatible component, a finalised disc should be used for playback.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback on anything other than this DVD Recorder. No more editing or recording can be made on the disc once it has been finalised.

When using a DVD-R disc

You should finalise the disc to play it on a component other than this DVD Recorder. You cannot edit or record on the disc once it has been finalised.

Unpacking

Accessories

Check for the supplied accessories below.

Preparing the Remote Control

Install Batteries in the Remote Control

???Open the battery cover on the back of the remote control.

???Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.

???Replace the battery cover.

If the remote does not operate properly:

???Check the polarity +/- of the batteries (Dry-Cell)

???Check if the batteries are drained.

???Check if remote sensor is blocked by obstacles.

???Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

Started ettingG

Setting the Remote Control

You can control certain functions of another manufacturer???s TV with this remote control. Control function buttons involve: STANDBY/ON, PROG / , VOL +/-, Direct Number buttons, TV MUTE, INPUT SEL. button.

Getting Started

To determine whether your television is compatible, follow the instructions below.

1.Switch your television on.

2.Point the remote control towards the television.

3.Press and hold the STANDBY/ON button and enter the two-figure code corresponding to the brand of your television, by pressing the appropriate number buttons.

Controllable TV Codes

Result: If your television is compatible with the remote control, it will switch off.

It is now programmed to operate with the remote control.

??? If several codes are indicated for your

NOTE

television brand, try each one in turn until you find one that works.

???If you replace the remote control's batteries, you must set the brand code again.

Then you can control the television using the following buttons after the TV button.

??? The various functions will not necessarily

NOTE

work on all televisions. If you encounter problems, operate the television directly.

1.STANDBY/ON

Turns the DVD Recorder on and off.

2.AV3 IN

Connect external equipment.

3.DISC TRAY

Opens to accept a disc.

4.OPEN/CLOSE

Opens and closes the disc tray.

5.DISPLAY

Displays the playing status, title/chapter/time, etc.

6.SEARCH/SKIP

Go to the next title/chapter/track or go back to the previous title/chapter/track.

7.PLAY/PAUSE

Plays a disc or pauses playback/recording.

8.P.SCAN

Selects the progressive scan mode.

9.PROG ( )

Select TV preset Channels.

Same as PROG button on the remote control.

10.REC

Starts recording.

11.STOP

Stops disc playback.

1.STANDBY/ON

Turns the DVD Recorder on and off.

2.AV3 IN

Connect external equipment.

3.DISC TRAY

Opens to accept a disc.

4.OPEN/CLOSE

Opens and closes the disc tray.

5.DISPLAY

Displays the playing status, title/chapter/time, etc.

6.SEARCH/SKIP

Go to the next title/chapter/track or go back to the previous title/chapter/track.

7.P.SCAN

Selects the progressive scan mode.

8.PROG ( )

Select TV preset Channels.

Same as PROG button on the remote control.

9.REC

Starts recording.

10.STOP

Stops disc playback.

11.PLAY/PAUSE

Plays a disc or pauses playback/recording.

1.STANDBY/ON

Turns the DVD Recorder on and off.

2.AV3 IN

Connect external equipment.

3.DV-IN

Connects extermal digital equipment with a DV jack. (such as a camcorder)

4.DISC TRAY

Opens to accept a disc.

5.OPEN/CLOSE

Opens and closes the disc tray.

6.DISPLAY

Displays the playing status, title/chapter/time, etc.

7.SEARCH/SKIP

Go to the next title/chapter/track or go back to the previous title/chapter/track.

8.PLAY/PAUSE

Plays a disc or pauses playback/recording.

9.P.SCAN

Selects the progressive scan mode.

10.PROG ( )

Select TV preset Channels.

Same as PROG button on the remote control.

11.REC

Starts recording.

12.STOP

Stops disc playback.

1.STANDBY/ON

Turns the DVD Recorder on and off.

2.AV3 IN

Connect external equipment.

3.DV-IN

Connects extermal digital equipment with a DV jack. (such as a camcorder)

4.DISC TRAY

Opens to accept a disc.

5.OPEN/CLOSE

Opens and closes the disc tray.

6.DISPLAY

Displays the playing status, title/chapter/time, etc.

7.SEARCH/SKIP

Go to the next title/chapter/track or go back to the previous title/chapter/track.

8.PLAY/PAUSE

Plays a disc or pauses playback/recording.

9.P.SCAN

Selects the progressive scan mode.

10.PROG ( )

Select TV preset Channels.

Same as PROG button on the remote control.

11.REC

Starts recording.

12.STOP

Stops disc playback.

1.Lights when a disc is loaded.

2.Lights in the record mode.

3.Lights to indicate the timer record mode.

4.Lights when a DVD-R/-RW disc is loaded.

5.Playing time/clock/current status indicator.

6.Lights in the progressive scan mode.

1. In from aerial connector

2. Out to TV connector

3.AV2(EXT) INPUT SCART Connector

4.AV1(TV) OUTPUT SCART Connector

5.DIGITAL AUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical audio input jack.

6.DIGITAL AUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial audio input jack.

7.AUDIO OUT

Connects to the audio input of external equipment using audio cables.

8.VIDEO OUT

Connects the input of external equipment using a Video cable.

9.S-VIDEO OUT

Connects the input of external equipment using an S-Video cable.

10.COMPONENT VIDEO OUT

Connects to equipment having Component video output.

???The Antenna connection does not pass output signal of DVD. To watch a DVD on

NOTE

your TV, you must connect audio/video cables.

Getting Started

Tour of the Remote Control

1.STANDBY/ON Button

2.0~9(Number) Buttons

3.TV/DVD Button

4.Reverse/Forward Skip Buttons

Press to skip a disc backwards or forwards.

5.Reverse/Forward Step Buttons

Press to play frame by frame.

6.Reverse/Forward Search Buttons

Press to search a disc backwards or forwards.

7.STOP Button

Press to stop a disc.

8.VOL Buttons

Volume adjustments.

9.AUDIO/TV MUTE Button

Use this to access various audio functions on a disc.(DVD mode)

This operates as Sound Mute. (TV mode)

10.MENU Button

Brings up the DVD recorder???s setup menu.

12.TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/Disc menu.

13.ANYKEY Button

Use this to view the status of the disc that is being played.

14.REC Button

Use to make a recording on DVD-RW/-R discs.

15.REC MODE Button

This will display the recording status.(XP/SP/LP/EP)

16.REPEAT Button

Allows you to repeat a title, chapter, track or disc.

17.OPEN/CLOSE Button

To open and close the disc tray.

18.SUBTITLE Button

Press this to switch the DVD???s subtitle language.

19.PLAY/PAUSE Button

Press to play a disc or pause playback/recording.

20.PROG Buttons

Select preset channels in a specific order. Same as PROG buttons in front panel.

21.RETURN Button

Returns to a previous menu.

22.PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the recorded files list.

23.CANCEL Button

24.MARKER/TIMER Button

Use this to bookmark a position while playing a disc.

Press to directly enter the Timer Recording Mode menu while stopping a disc.

25.INFO Button

This will display current settings or disc status.

26.TV Button

Press this to operate TV.

27.DVD Button

Press this when you use a DVD recorder.

28.INPUT SEL. Button

Select line input signal in external input mode [PROG, AV input or DV INPUT(DVD-R130, R131 only)]

29.ZOOM Button

Press this to enlarge the screen.

Connecting

& Setting Up

This section involves various methods of connecting the DVD Recorder to other external components and required initial setting modes.

Quick Overview

A Quick Overview presented in this guide will give you enough information to start using the DVD Recorder.

Connecting the DVD Recoder

???

Additional connections

???

Antenna + DVD Recorder + external decoder box + TV

???

Other type of connecting the Video output cable

???

Other type of connecting the Audio output cable

???

Connecting to AV3 IN, DV input jack (DVD-R130, R131 only)

Up Setting & onnectingC

Connecting & Setting Up

You can connect your DVD Recorder to the television using the SCART cable if the appropriate input is available on the television.

1.Connect the RF cable as shown.

2.Connect one end of the SCART cable to the AV1 socket on the rear of the DVD Recorder.

3.Plug the other end into the appropriate connector on the television.

4.Plug in the DVD Recorder and TV

5.Turn on the DVD Recorder and TV.

6.Press the INPUT SEL. button on your TV remote control until the Video signal from the DVD Recorder appears on the TV screen.

To RF IN

To RF OUT

RF Cable

To ANT INPUT

??? The RF cable connection of this DVD

You can connect your DVD Recorder to a satellite or

digital tuner.

external device (VCR/Satellite receiver)

- DVD mode

1.Connect the AV2 connector of DVD Recorder and VCR/Satellite receiver or digital tuner using a SCART cable.

2.Connect the AV1 connector to the SCART AV connector on TV.

3.Turn on the DVD Recorder, VCR/Satellite receiver or digital tuner and TV.

4.Set Input mode on AV2.

- TV mode

NOTE

Recorder sends only signals of TV. You must connect SCART cable or

Audio/Video cables to watch a signal from your DVD Recorder.

???TV mode

Press the TV/DVD button on remote control, then ???TV??? appear on Front LED display (or turn off DVD Recorder).

If you connect external decoder box to DVD recorder, you can record scrambled channels (CANAL+or Premiere broadcasts) received through the built-in TV tuner in DVD Recorder.

Wall

DECODER

1.Connect RF antenna cables as shown.

2.Connect the AV1 connector on this recorder to the SCART AV connector on TV using a SCART cable.

3.Connect the AV2 connector to a SCART AV connector on decoder box.

4.To watch or record PAY-TV Canal Plus programmes, set your DVD Recorder to receive the channels using the on-screen display.(Refer to page 28)

There are several ways to output video signal not using scart cables. Select one of the following video connecting that best suits you below.

???Case 1 : Connecting to a Video (Composite) output jack

???Case 2 : Connecting to an S-Video output jack

???Case 3 : Component Video output jacks

S-Video, Component video and Progressive Output Modes

???S-Video and Component video output are available only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check the TV connections and the TV input selection settings.

???Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to your TV, resulting in a more stable, flicker-free, clear image than interlaced video.

This is only available with TVs that support progressive scan.

???Progressive Scan Output (576p)

Consumers should note that not all high definition television sets are fully compatible with this DVD Recorder and may cause artifacts to be displayed in the picture, in case of 576 progressive scan picture problems, It is recommended that the user switch the connection to the ???standard definition??? output. If there are questions regarding our TV set compatibility with this model 576p DVD Recorder, please contact our customer service centre.

Up Setting & onnectingC

Connecting & Setting Up

Case 1 : Connecting to a Video (Composite) output jack

1.Connect a video(yellow) cable between the VIDEO (yellow) OUT jack on DVD Recorder and VIDEO (yellow) INPUT jack on your TV (or AV amplifier). ??? You will enjoy regular quality images.

2.Connect audio cables (white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or AV amplifier).

(See pages 21-22)

Case 2 : Connecting to an S-Video output jack

1.Connect an S-Video cable (not included) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO INPUT jack on your TV (or AV amplifier).

2.Connect audio cables (white and red) between the AUDIO OUT jacks on DVD Recorder and AUDIO IN jacks on TV (or AV amplifier).

??? You will enjoy high quality images.

Case 3 : Component Video

output jacks

1.Connect Component video cables(not supplied) between the COMPONENT OUT(Y,PB,PR) jacks on

DVD Recorder and COMPONENT IN(Y,PB,PR) jacks on your TV.

2.Connect audio cables (white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or AV amplifier).

(See pages 21-22).

3.After connecting, refer to the page 34 to 35.

???You will enjoy high quality and accurate colour reproduction images.

Other type of connecting the Audio output cable

There are several ways to output audio signal not using scart cables. Select the audio connection that best suits you below.

???Case 1 : Connecting to your TV

???Case 2 : Connecting to a stereo amplifier with AV output jacks

???Case 3 : Connecting to an AV amplifier with a digital output jack

Manufactured under licence from Dolby Laboratories. ???Dolby??? and the double-D symbol are trademarks of Dolby Laboratories.

???DTS??? and ???DTS Digital Out??? are trademarks of DTS, Inc.

Up Setting & onnectingC

??? Make sure that the colour coded NOTEconnections match. The Y, PB, PR

component output jacks of your DVD Recorder must be connected to the exact corresponding component input jacks on your TV.

???Progressive setting is only available when the Video Out is set to Component.

(See page 34)

yellow

white

red

Case 2 : Connecting to a stereo amplifier with AV output jacks

If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.

Case 3: Connecting to an AV amplifier with a digital output jack

If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. (See pages 32-33)

Connecting & Setting Up

Connecting to AV3 IN, DV input jack (DVD-R130, R131 only)

This allows you to connect your DVD Recorder to other external devices and view or record their outputs.

??? Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks

??? Case2 : Connecting a Camcorder to the DV IN jack (DVD-R130, R131 only)

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks

Connecting a VCR or external device to AV3 IN jacks of the DVD Recorder.

You can record from connected equipment (VCR, STB, DVD player or Camcorder).

Case 2 : Connecting a Camcorder to the DV IN jack (DVD-R130, R131 only)

If your digital camcorder has a DV output jack, connect it to the DV input jack of your DVD Recorder.

Camcorder

??? If the input is not selected automatically,

Up Setting & onnectingC

DVD

yellow

white

red

??? AV 3 IN selection will be automatically

NOTE

use INPUT SEL. button to select proper input.

NOTE

done. If the input is not selected automatically, use INPUT SEL. button to select proper input.

System Setup

System

Setup

On-Screen Menu

Navigation

The on-screen menus allow you to enable or disable various functions on your DVD Recorder.

Use the following buttons to open and navigate through the on-screen menus.

1 MENU Button

Press this button on the remote control to open the on-screen MENU.

Press again to exit the on-screen MENU.

2 ??? ??? , ?? ??? Buttons

Press these buttons on remote control to move the selection bar ??? ??? , ?? ??? to cycle through the menu options.

3 OK Button

Press this button on the remote control to confirm any new settings.

4 RETURN Button

Press this button on the remote control to return to the Previous MENU screen displayed or to exit the on-screen MENU.

Plug & Auto Setup

Your DVD Recorder will automatically set itself up when it is plugged in for the first time. TV stations and clock will be stored in memory. The process takes a few minutes. Your DVD Recorder will then be ready for use.

1 Connect the RF cable as indicated on page

18.

(Connecting Your DVD Recorder to the TV Using the RF Cable and scart cable.)

2 Plug the DVD Recorder into the mains.

???Auto??? in the front panel display flickers.

??? Refer to following abbreviation table when selecting ???Country???.

???The DVD Recorder searches for the stations according to a preset preference list corresponding to the country that you have selected.

6 Auto Channel scan will be started.

Auto channel memory

17%

Stop

???The number of stations automatically stored by the DVD Recorder depends on the number of stations that it has found.

Setup ystemS

3 Select the language using the ?????? buttons, then press the OK button.

4 Press the OK button or wait for a few seconds to start the auto setup.

No Disc

Auto setup will be started.

Check antenna and TV cable connection.

OK RETURN

5 Select ???Country??? using the ???????? ??? buttons to select your country then press the OK button.

7 Check the date and time.

???if it is : Correct, press the OK button then the date and time will be saved. If you don't press the OK button, the date and time will be saved automatically after 5 seconds.

???if it is : Incorrect, input correct Time, Date, Year using ???????? ??? buttons or number buttons. Press the OK button then the date and time will be saved. When you need to change clock setting, you can set up it manually.

(see page 26.)

??? Now, DVD Recorder is ready for use. NOTE Function for ???Plug & Auto Setup??? is fixed

already. So if you want to change this fixed one, you can change it by Presetting the Stations in OSD ???Presetting Channels with the Manual set up function??? menu.

(see page 28)

???Auto Setup function can be performed by pressing and holding down the PROG () buttons on the front panel of the DVD Recorder simultaneously for more than 5 seconds with no disc in the DVD Recorder.

System Setup

Setting the Clock

This menu is used to set the current time.

You need to set the time to use timer recording.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

3 Press the ?????? buttons to select Clock Set, then press the OK or ??? button.

Use the ???????? ??? buttons to input Time, Date or Year. Use number buttons to input clock data directly.

4 Press the ?????? buttons to select On for the Auto Clock.

5 Press the OK button, then the date and time will be saved.

If you don???t press the OK button, it will not be saved.

???The DVD Recorder automatically sets the clock according to the time signal broadcast between the channels PR1 to PR5. If you do not need the Auto clock set function, select Off.

Presetting Channels with the Auto Setup function

This feature allows you to manually set the DVD Recorder tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.

4 Press the ?????? buttons to select Auto Setup, then press the OK or ??? button.

The Country Seletion screen is displayed.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

5 Press the ???????? ??? buttons to select your ???Country???, then press the OK button.

???The DVD Recorder searches for the stations according to a preset preference list corresponding to the country that you have selected.

Refer to following table when selecting your country.

Setup ystemS

Presetting Channels with the Manual Setup function

You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels.

4 Press the ?????? buttons to select Manual Setup, then press the OK or ??? button.

Manual Setup

System Setup

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

No Disc

Programme Scheduled Record List???

Setup

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

5 Press the ?????? buttons to select a PR (programme) you wish to edit, delete, or swap, then press the OK or ??? button. Select Edit, Delete or Swap using the ?????? buttons, then press the OK or ??? button.

Manual Setup

???Edit : You can add or edit PR(programme). After change PR informations(CH, Name, Decoder, MFT), select Done, then press the OK button.

Manual Setup

3 Press the ?????? buttons to select Install, then press the OK or ??? button.

-CH : Tune the channel using ?? ??? buttons.

-Name : Display station name automatically detected in broadcasting signal. If not detected, you can edit name by using ???????? ??? buttons.

-Decoder : If you set on, you can record scrambled channels using external decoder box. Before setting on, refer to connecting external decoder box in the page 19.

-MFT : You can tune up the channel frequency better using ?? ??? buttons.

???Delete : the channel information of selected PR(programme) will be removed.

???Swap : You can swap the channel information of two PR(programme). For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the OK button at PR5.

Setting up the Language Options

If you set the audio, subtitle, disc menu, on-screen menu, DivX subtitle language in advance, they will come up automatically every time you watch a movie.

If the selected language is not recorded on the disc, the original pre-recorded language is selected.

4 Press the ?????? buttons to select the desired language option, then press the OK or ??? button.

???Audio : For the speaker sound.

???Subtitle : For the disc subtitles.

???Disc Menu : For the disc menu contained on the disc

???On-Screen Menu : For the screen of your DVD Recorder

???DivX Subtitle: Selecting a supported DivX subtitle language by region.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

Western

Afrikaans, Basque, Catalan, Danish, Dutch,

English, Faeroese, Finnish, French, German,

Icelandic, Indonesian, Italian, Malay, Norwegian,

Portuguese, Spanish, Swahili and Swedish

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

English, Albanian, Croatian, Czech, Hungarian,

Central Polish, Romanian, Serbian(Latin), Slovak and

Slovenian

Greek English and Greek

English, Azeri, Belarusian, Bulgarian, Kazakh,

Cyrillic Macedonian, Russian, Serbian, Tatar, Ukrainian

and Uzbek

5 Press the ?????? buttons to select the desired language, then press the OK or ??? button.

??? Press the RETURN or ?? button to return

Setup ystemS

3 Press the ?????? buttons to select Language, then press the OK or ??? button.

NOTE

to the previous menu.

Press the MENU button to exit the menu.

Language setup menu will be displayed.

???The selected language will only appear if it is supported on the disc.

???If the subtitle language is displayed in broken fonts, change DivX Subtitle to the appropriate region.

If it still does not work, the format is not supported.

EP Mode Time Setting

You can select one of four recording modes by pressing the REC MODE button repeatedly.

EP mode is one of four REC Mode (XP,SP,LP,EP).

In EP(Extended Play) mode, you can set recording time to 6 or 8 hours by this setting.

4 Press the ?????? buttons to select EP Mode Time, then press the OK or ??? button.

System Setup

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

No Disc

Programme Scheduled Record List???

Setup

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

3 Press the ?????? buttons to select System, then press the OK or ??? button.

System menu will be displayed.

5 Press the ?????? buttons to select the desired time, then press the OK or ??? button.

Automatic Chapter

Creation

A DVD-Video consists of ???Titles??? and ???Chapters???. When you record one programme, it makes one Title. If you use this function, the Title will be divided into Chapters.

(V mode)

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

3 Press the ?????? buttons to select System, then press the OK or ??? button.

System menu will be displayed.

5 Press the ?????? buttons to select On or Off, then press the OK or ??? button.

???Off: Select this option when you do not want (Automatic Chapter Creation).

???On: Select this option when you want (Automatic Chapter Creation).

6 Press the REC button to start recording. (See page 42 about how to set recording mode) The message ???Do you want to create the chapter menu after this recording???? is displayed.

Do you want to create the chapter menu

after this recording?

Yes No

7 Press the ?? ??? buttons to select Yes and press the OK button.

???A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode.

8 Press the STOP button to stop recording.

9 To display the created chapters, finalise the disc (see page 84) and then press the DISC MENU button. The chapter menu will be displayed.

Setup ystemS

ystem Setup

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

No Disc

Programme Scheduled Record List???

Setup

DivX(R) Registration

Please use the Registration code to register this DVD Recorder with the DivX(R) Video On Demand format. For more information, visit www.divx.com/vod

S

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

Setting up the Audio

Options

You can connect the DVD Recorder to an external amp or Home Theatre.

Allow you to setup the Audio device and sound status depending on the audio system in use.

3 Press the ?????? buttons to select System, then press the OK or ??? button.

System menu will be displayed.

4 Press the ?????? buttons to select Quick Recording, then press the OK or ??? button.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

No Disc

3 Press the ?????? buttons to select Audio, then press the OK or ??? button.

Audio setup menu will be displayed.

DTS

1. Off : Doesn???t output DTS signal.

Select this when your AV receiver or AV amplifier does not have DTS decoder.

2. On : Outputs DTS Bitstream via digital output when you play DTS track.

Select this only when your AV receiver (or AV amplifier) have DTS decoder.

4 Press the ?????? buttons to select the desired audio option, then press the OK or ??? button.

5 Press the ?????? buttons to select the desired item, then press the OK or ??? button.

???Press the RETURN or ?? button to return to the previous menu.

NOTE

Press the MENU button to exit the menu.

Audio Options

Digital Output

1.PCM : Select this when you have no equipment that can decode Dolby Digital (or MPEG-2) signal. When you play Dolby Digital (or MPEG-2) sound track, the digital output are converted to PCM Stereo.

2.Bitstream : Output Dolby Digital (or MPEG-2) audio as

bitstream. Select this when your AV receiver or AV amplifier have Dolby Digital (or MPEG-2) Decoder.

??? Digital output setting is equally applied to

Dynamic Compression

This is only active when a Dolby Digital signal is detected.

1.Off : You can enjoy the movie with the standard Dynamic Range.

2.On : When Movie soundtracks are played at low volume or from smaller speakers, the system can apply appropriate compression to make low-level content more intelligible and prevent dramatic passages from getting too loud.

NICAM

NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound by setting NICAM on or off.

1.On : NICAM mode

2.Off : Only set at this position to record the standard mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.

Setup ystemS

NOTE

both Dolby Digital and MPEG-2 audio. LPCM sound track is always outputted as PCM. It has no relation with Digital Output setting.

Setting up Video Output Options

You can enjoy high quality image through RGB or Component video connections.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

4 Press the ?????? buttons to select Video Output, then press the OK or ??? button.

Component

Select this when the DVD Recorder is connected to a TV with Component jack.

RGB

Select this when the DVD Recorder is connected to your TV using SCART cable.

System Setup

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

3 Press the ?????? buttons to select Video, then press the OK or ??? button.

Video setup menu will be displayed.

5 Press the ?????? buttons to select the desired item, then press the OK or ??? button.

In Component mode, you can set video output to Progressive(P.SCAN) or Interlace, see page 35.

Available video output jacks are as follow.

Available Video Output Jack

If the TV supports Progressive Scan, press the P.SCAN button on the front of the DVD Recorder to enjoy.

1 With the DVD Recorder in Stop mode, press the P.SCAN button on the front of the DVD Recorder.

The message ???Press [Yes] to confirm Progressive scan mode. Otherwise press [No]??? will appear.

Press [Yes] to confirm Progressive scan mode.

Otherwise press [No]

Yes No

1 With the DVD Recorder in Stop mode, press the P.SCAN button on the front of the DVD Recorder.

The message ???Press [Yes] to confirm Interlace scan mode. Otherwise press [No]??? will appear.

Press [Yes] to confirm Interlace scan mode.

Otherwise press [No]

Yes No

2 Press the ?? ??? buttons to select Yes, and then press the OK button.

Setup ystemS

2 Press the ?? ??? buttons to select Yes, and then press the OK button.

3 Set your TV to Progressive input (using the

3 Set your TV to Interlace input (using the TV remote control.)

??? If you press the P.SCAN button by

TV remote control.)

??? Do not press the P.SCAN button if you

NOTE

mistake when your TV does not support Progressive mode, you need to release the Progressive mode. To release the Progressive mode, press the P.SCAN button on the front panel 2 times.

NOTE

are using a TV that does not support Progressive mode. Nothing will be displayed on the screen if pressed.

The screen will recover after the PS LED on the front panel display turns off.

System Setup

Setting up the Display(Video) Options

This function allows you to setup the TV screen settings.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

2 Press the ?????? buttons to select Setup, then press the OK or ??? button.

3 Press the ?????? buttons to select Video, then press the OK or ??? button.

Video setup menu will be displayed.

4 Press the ?????? buttons to select the desired video option, then press the OK or ??? button.

5 Press the ?????? buttons to select the desired item, then press the OK or ??? button.

??? Press the RETURN or ?? button to return

NOTEto the previous menu. Press the MENU button to exit the menu.

Display(Video) Options

This function depends on disc type. It may not work for some disc types.

TV Aspect

Depending on the type of television you have, you may want to adjust the screen setting. (aspect ratio)

??? 4:3 LetterBox : Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen.

Black bars will appear at the top and bottom of the screen.

??? 4:3 Pan-Scan : Select this for conventional size TV when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.)

??? 16:9 Wide : You can view the full 16:9 picture on your widescreen TV.

3D Noise Reduction (motion adaptive noise reduction)

???On : Provides a cleaner picture through noise reduction (for recording).

???Off : Normal

Setting up the Parental Control

The Parental Control function works in conjunction with DVDs that have been assigned a rating which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

4 Enter the 4-digit password using the 0 to 9 buttons on the remote control.

The ???Confirm the password??? message will be displayed. Enter your password again.

1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.

5 Press the OK or ??? button to select

Password.

Setup ystemS

??? Press the RETURN or ?? button to return

NOTE

to the previous menu. Press the MENU button to exit the menu.

3 Press the ?????? buttons to select Parental Control, then press the OK or ??? button.

The ???Create the password??? message will be displayed.

If you forgot your password

1 Remove the disc.

2 Press and hold down the PROG () buttons on the front panel of the DVD Recorder simultaneously for more than 5 seconds with no disc in the DVD Recorder.

All setting including the password will revert to the factory setting.

About the Rating Level

1 Press the ?????? buttons to select Rating Level.

About the Change Password

1 Press the ?????? buttons to select Change Password.

System Setup

3 Press the ?????? buttons to select Rating Level you want, then press the OK or ??? button.

For example, if you select up to Level 6, discs that contain Level 7, 8 will not play. A larger number indicates that the programme is intended for adult use only.

3 Enter the 4-digit password using the 0 to 9 buttons on the remote control.

The ???Confirm the password??? message will be displayed. Enter your password again.

??? See page 37 if you forgot your password.

NOTE

Recording

This section shows various DVD recording methods.

Before Recording

This DVD Recorder can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference.

Recordable discs

This DVD Recorder can record on the following discs.

???DVD-RWs are rewritable.

???DVD-Rs are non-rewritable

Compatibility between Samsung and Other Company???s Recorder

???Unfinalise

-This allows additional recording on a DVD-RW disc originally recorded on the DVD Recorder.

-A DVD-RW disc that has been recorded by DAO(Disc At Once) in a PC cannot be unfinalised.

-A DVD-RW disc that has been recorded in Video Mode of a different maker???s recorder cannot be unfinalised.

-A DVD-R disc cannot be unfinalised.

ecordingR

Recording

Recording Formats

Since available functions differ depending on the disc type, select a disc that best fits your preferences; When you insert an unused disc, the following message appears

DVD-RW: When a blank disc is first inserted, the message ???Uninitialized Disc Do you want to initialize this disc???? will appear.

When Yes is selected, the disc will be formatted in VR Mode.

Uninitialized Disc

Do you want to initialize this disc?

Yes No

If you want to format in either VR Mode or Video Mode, refer to Formatting a Disc on pages 82~83.

DVD-R: Formatting DVD is unnecessary and only Video Mode Recording is supported

DVD-RW(Video mode)/-R

???Chapters will be created automatically when you finalise recording on DVD-R / DVD-RW discs in Video mode with the Chapter Creator has been set to On. The chapter???s length (interval between chapters) varies according to the recording mode.

???Simple editing (erasing titles/changing title name)

DVD-RW(VR mode)

???This mode allows multiple editing functions (such as deletion of the whole title, partial deletion of a title, etc.)

???Various editing options using a created Playlist

Recording Mode

Select one of four recording modes by pressing the REC MODE button repeatedly while the DVD Recorder is in Stop mode for the desired recording time and picture quality.

In general, picture quality improves as the recording time decreases. In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording.

This function is selected only one mode in XP, SP, LP and EP modes and you can use this mode for timer recording.

Unrecordable video

Video with copy protection cannot be recorded on this DVD Recorder.

When the DVD Recorder receives a copy guard signal while recording, recording stops and the following message appears on the screen.

You cannot record copy protected movie.

Concerning Copy Control Signals

TV broadcasts that contain copy control signals may have one of the following three signal types, Copy-Free, Copy-Once and Copy-Never. If you want to record a copy-once type programme, use DVD-RW with CPRM in VR Mode.

Once ???Copy Once??? has been recorded, recording cannot be done anymore.

- Content Protection for Recordable Media (CPRM)

CPRM is a mechanism that ties a recording to the media on which it is recorded. It is supported by some DVD recorders, but not by many DVD players. Each blank recordable DVD has a unique 64-bit media ID etched in the BCA. When protected content is recorded onto the disc, it can be encrypted with a 56-bit C2 (Cryptomeria) cipher derived from the media ID. During playback, the ID is read from the BCA and used to generate a key to decrypt the contents of the disc.

If the contents of the disc are copied to other media, the ID will be absent or wrong and the data will not be decryptable.

About INFO Button

Recording the current TV programme you are watching

Checking the available disc space (Disc Information)

When recording on an used disc, make sure that there is enough disc space for recording. With DVD-RWs, you can free up disc space by erasing titles.

???Press the INFO button.

The display window of disc information appears. Items in the display differ depending on the disc type or recording format.

^Recordable Time 02:12 SP

1 Press the OPEN/CLOSE button and place a recordable disc on the disc tray.

2 Press the OPEN/CLOSE button to close the disc tray.

Wait until ???LOAD??? disappears from the front panel display.

If an unused DVD-RW disc is used, whether to initialize or not will be asked first. Make your selection, then press the OK button.(See page 40.)

Uninitialized Disc

Do you want to initialize this disc?

Yes No

ecordingR

1.Disc Type

2.Current information display status

3.Disc Name

4.Total Title : Total number of titles

5.Total Playlist : Total number of Playlists

6.Recordable Time : The longest continuous recording time in each of the recording modes(approximate)

7.Date : Current date and time

3 Press the PROG ( / ) or number ( ~ ) buttons to select the current programme you want to record.

Recording

4 Press the REC MODE button repeatedly, (or press the REC MODE button, then press the ?????? button) to select the recording speed(quality).

??? SP ??? LP ??? EP ??? XP

5 Press the REC button.

Information concerning the channel is displayed on the screen, then recording begins.

REC icon( ) is displayed on the front panel.

Recording : PR 1 NICAM DUAL L

To view the current status of the disc and progress of recording : Press the INFO button, the information about the disc will appear.

Press the INFO button once again to view information about the recording.

To stop recording

Press the STOP button to stop a recording in progress.

???When using DVD-RW/DVD-R discs, the message ???Updating the disc information.

Please wait for a moment.??? is displayed.

???You can not change the recording mode

and the PROG while recording.

NOTE

???Recording will stop automatically if there is no free space left for recording.

???Up to 99 titles can be recorded onto a disc.

???Recording will stop automatically if a copy protected image is selected.

???DVD-RW discs must be

formatted before starting to record. Most new discs are sold unformatted.

???Do not use DVD-R authoring discs with this DVD Recorder.

Recording from external equipment you are watching

Before you start

Check that the disc has enough available space for the recording. Adjust the recording mode.

1 Press the OPEN/CLOSE button, place a recordable disc on the disc tray.

2 Press the OPEN/CLOSE button to close the disc tray.

Wait until ???LOAD??? disappears from the front panel display.

If an unused DVD-RW disc is used, whether to initialize or not will be asked first. (See page 40)

3 Press the INPUT SEL. button to select the input source according to the connection you made.

The front panel display changes in the following sequence: (DV input is display only DVD-R130, R131)

??? PR Number ??? AV1 ??? AV2 ??? AV3 ??? DV

If you connect a digital camcorder, press the INPUT SEL. button to select DV.

(See pages 43-44)

4 Press the REC MODE button repeatedly, (or press the REC MODE button, then press the ?????? button) to select the recording speed(quality).

???SP ??? LP ??? EP ??? XP

5 Press the REC button.

To pause recording

Press the PLAY/PAUSE( ) button to pause a recording in progress.

???Press the PLAY/PAUSE( ) button again to resume recording.

???You can switch channels by pressing the PROG

( / ) buttons while recording pauses.

To stop recording

Press the STOP button to stop or finish a recording in progress.

???When using DVD-RW/DVD-R discs, the message ???Updating the disc information.

Please wait for a moment.??? is displayed.

???You can not change the recording mode

while recording or Pause.

NOTE

???Recording will stop automatically if there is no free space left for recording.

???Up to 99 titles can be recorded onto a disc.

???Recording will stop automatically if a copy protected image is selected.

???DVD-RW discs must be

formatted before starting to record. Most new discs are sold unformatted.

???Do not use DVD-R authoring discs with this DVD Recorder.

Copying from a Camcorder (DVD-R130, R131 only)

You may control the Camcorder using the IEEE1394 (DV) interface.

Before you start

Check that the disc has enough available space for the recording. Adjust the recording mode.

1 Press the OPEN/CLOSE button, place a recordable disc on the disc tray.

ecordingR

Recording

2 Press the OPEN/CLOSE button to close the disc tray.

Wait until ???LOAD??? disappears from the front panel display.

If an unused DVD-RW disc is used, whether to initialize or not will be asked first. (See page 40.)

3 Press the REC MODE button repeatedly, (or Press the REC MODE button, then press the ?????? button) to select the recording speed(quality).

??? SP ??? LP ??? EP ??? XP

4 Press the INPUT SEL. button to select DV.

If the input is set to DV, a playback/record menu that enables camcorder control appears on the top of the screen.

DV

5 To play the camcorder and find the starting point to be copied, select the play icon( ) on the top of the screen using the ?? ??? buttons and then press the OK button.

6 To start recording, select the record icon() on the top of the screen using the ?? ??? buttons and then press the OK button.

You can also use the REC button on the remote control to start recording. (If your camcorder is in stop mode, the REC button doesn't work.)

To stop recording

Press the STOP button to stop or finish a recording in progress.

???When using DVD-RW/DVD-R discs, the message ???Updating the disc information. Please wait for a moment.??? is displayed

???You can not change the recording mode and input source while recording.

NOTE

???Recording will stop automatically if there is no free space left for recording.

???Up to 99 titles can be recorded onto a disc.

???Recording will stop automatically if a copy protected image is selected.

???DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted.

???Do not use DVD-R authoring discs with this DVD Recorder.

???If you connect a camcorder using DV jack, the related contol menu appears automatically. To access on the screen controls during recording, press ?? or ??? button.

Making a One Touch

Recording (OTR)

You can set the DVD Recorder to record in preset increments by pressing the REC button repeatedly.

1 If you want to record a TV channel, press the PROG ( / ) or number buttons to select a desired channel.

If you want to record through a connected external component, press the INPUT SEL. button to select an appropriate external input [AV1, AV2,

AV3 or DV(DVD-R130, R131 only)].

??? TV PROGRAMME: 1 to 99

2 Press the REC button to start recording.

3 Press the REC button repeatedly to adjust the desired recording time.

???0:30 ??? 1:00 ??? ... 4:00 ??? 5:00 ??? ... 9:00 ???normal

???The timer counter decreases by the minute from 9:00 to 0:00, then the DVD

NOTE

Recorder stops recording and is powered off.

To view the current status of the disc and progress of recording : Press the INFO button, and information about the disc will appear.

Press the INFO button once again.

Then you can check the information about the title being recorded.

Making a Timer Recording

Before you start

1.Check the antenna cable is connected.

2.Check the remaining time of the disc.

3.Check the date and time are correct.

Make sure the Clock (Setup-Clock Set) must be set before you proceed with a timer recording.

(See page 26)

3 Set timer recording option.

??? Fill the input items using the direction buttons and number buttons.

?? ??? : Moves to the previous/next item,

??????, 0~9 : Sets a value.

ecordingR

Recording

???Source : The video input source (???AV1???, ???AV2???, ???AV3???) or the broadcasting

channel you want to make a timer recording from.

???Day : Timer Recording allows setting the recording time within one month period. Set the recording day.

??? Start/End Time : Start and end time of the timer recording.

???Speed (Recording Mode) :

-FR (Flexible Recording) : Select when you want to set video quality automatically.

In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording. This function is selected only one mode in XP, SP, LP and EP modes and you can use this mode for timer recording.

-XP (high quality) : Select when video quality is important. (Approx. 1 hour)

-SP (standard quality) : Select to record in standard quality. (Approx. 2 hours)

-LP (low quality) : Select when a long recording time is required.(Approx. 4 hours)

-EP (extended) : Select when a longer recording time is required. (Approx.6 hours or 8 hours)

???V/P : VPS(Video Programme System) or PDC(Programme Delivery Control) function.

-If you set this function on, you can control the starting and ending time of recording by special signal included in the broadcasting signal.

If a TV programme is shortened or starts earlier or later than scheduled, this function synchronizes the starting and ending time of recording with the actual broadcasting time automatically.

-Set up the start-time EXACTLY according to the published TV schedule. Otherwise the timer recording will not take place.

-Do not select PDC or VPS unless you are sure the programme you wish to record is broadcast with PDC or VPS.

??? When you are recording at EP mode on a

NOTEDVD-RW(V)/-R disc, it may not record the full 6 or 8 hours because the DVD

Recorder uses the VBR(Variable Bit Rate) ENCODING system. For example, if you record a programme with a lot of action, it uses a higher bit rate which in turn consumes more disc memory.

4 Press the OK button.

If the timer settings overlap

The programmes are recorded in order of priority. If timer recording is set for the first programme and then again for the second programme and both programmes overlap, the following message will appear on the screen: ???This setting is identical with 1???The message shows that the first programme has priority. After recording of the first programme is complete, the second programme starts being recorded.

To exit without saving the current setting

Press the MENU button.

To return to the previous menu

Press the RETURN button if you don???t want to set a timer recording.

5 Turn the power off to finish the Timer Recording setting. Timer Recording will not work when the power is on.

??? will appear on the front panel. It means that a timer recording is registered.

??? will blink if disc is not inserted.

??? The timer recording time may differ from

NOTEthe set time depending on disc status and overall timer recording status (for

example, recording times overlapping, or when the previous recording ends within 2 minutes before the start time of the next recording.)

???You can make the Timer Recording up to 12 programmes.

Flexible Recording

(for Timer recording only)

In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording. This function is selected only one mode in XP, SP, LP and EP modes and you can use this mode for timer recording.

The FR mode recording setup is the same as Timer Recording. When setting the mode in step 3, set FR Mode.(See pages 45~46.)

Editing the Scheduled

Record List

Follow these directions to edit the timer record list.

1 With the DVD Recorder in Stop mode, press the TIMER button.

Using the MENU button.

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Programme, then press the OK or ??? button.

4 Press the ?????? buttons to select Edit, then press the OK or ??? button.

???The Timer Record Input item is displayed. Edit the items you want to modify.

See the ???Making a Timer Recording??? section for more information on Timer Recording Input items.

5 Press the OK button to confirm the edited setting.

6 Press the MENU button after finishing the operation. The menu screen will disappear.

2 Press the OK or ??? button.

3 Press the ?????? buttons to select the number of the timer recording you want to edit, then press the OK or ??? button.

??? The Edit and Delete items are displayed.

Deleting the Scheduled

Record List

Follow these directions to delete an entry from the timer record list.

1 With the DVD Recorder in Stop mode, press the TIMER button.

Using the MENU button.

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Programme, then press the OK or ??? button.

2 Press the OK or ??? button.

ecordingR

Recording

3 Press the ?????? buttons to select the number of the timer recording you want to delete, then press the OK or ??? button.

??? The Edit and Delete items are displayed.

No. Source Day Start End Speed V/P Edit

4 Press the ?????? buttons to select Delete, then press the OK or ??? button.

???You will be prompted with the delete confirm message such as ???Do you want to delete

5 Press the ?? ??? buttons to select Yes, then press the OK button.

??? The selected entry will be deleted from the list.

6 Press the MENU button after finishing the operation. The menu screen will disappear.

Recording the Standard

Timer List

When the start time in the Scheduled record list reaches while the set is in power off, the set will be powered on and start the recording automatically.

1 When the scheduled recording is operating, the programme being recorded will not display on TV.

???Press the TV/DVD button if you want to see the programmed being recorded on TV.

???Press the TV/DVD button again if you don???t want to see the programmed being recorded on TV.

To stop Recording

Press the STOP button. The message ???Press STOP button once more to cancel Timer Record.??? is displayed.

Press STOP button once more

to cancel Timer Record.

Press the STOP buttons once more to stop recording.

???If there is not enough disc space or a copy prevention signal is received during

NOTE

recording, recording will stop.

You cannot record copy protected movie.

???If there is no free disc space or the disc is not recordable, recording will not operate. (You can record after replacing the disc.)

Playback

This section introduces basic functions of playback and playback by disc type.

Read the following information before playing a disc.

Region code (DVD-Video only)

Both the DVD recorder and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this DVD Recorder is described on the rear panel of the DVD Recorder.

Disc types that can be played

Discs that cannot be played

???DVD-Video with a region number other than ???2??? or ???ALL???

???3.9 GB DVD-R Disc for Authoring.

???DVD-RW(VR mode) not recorded following the Video Recording Standard

???Unfinalised DVD-R,unfinalised DVD-RW(V mode) recorded on other equipment.

???DVD-ROM/PD/MV-Disc, etc

???Video CD/SVCD/CVD/CD-ROM/CDV/CD-G/CD-I

laybackP

Playback

???Playback and/or recording may not work for some types of discs, or when specific

???Do not allow the disc to become dirty or scratched. Fingerprints, dirt, dust, scratches or deposits of cigarette smoke on the recording surface may make it impossible to use the disc for recording.

???DVD-RW/-R discs may not be able to play on some DVD Recorders, depending on the player, disc and the condition of the recording.

Playing a Disc

1 Press the OPEN/CLOSE button.

2 Place a disc gently into the tray with the disc???s label facing up.

3 Press the OPEN/CLOSE button to close the disc tray.

???Your DVD Recorder closes the disc tray and plays the disc automatically.

???The DVD Recorder does not play discs automatically after the initial power on.

???When the DVD Recorder is powered on and a disc is in the tray, the DVD Recorder will be activated and wait in stop status.

???Press the PLAY button to start playback.

???If you want the DVD Recorder to play automatically when it is powered Off with a disc in the DVD Recorder, power on with the PLAY button.

4 Press the STOP button to stop playback.

???When you stop playing disc, the DVD Recorder remembers where you stopped.

NOTE

When you press the PLAY button again, it will pick up where you left off. (unless the disc is removed or the DVD Recorder is unplugged, or if you press the STOP button twice.) This function is only applicable to DVD-VIDEO, DVD-RW, DVD-R or audio CDs (CD-DA).

???Do not move your DVD Recorder while playing, as this may cause damage to the

CAUTION

disc.

???Make sure to press the OPEN/CLOSE button to open or close the disc tray.

???Do not push the disc tray while it is being opened or closed, as this may cause a malfunction of the DVD Recorder.

???Do not place foreign materials on or in the disc tray.

???Some functions may perform differently or be disabled depending on the disc type. If this occurs, refer to the instructions written on the disc case.

???Be especially careful that children's fingers are not caught between the disc tray and the tray chassis when it closes.

???You must only insert one DVD disc at a time. Inserting two or more discs will not allow playback and may cause damage to the DVD RECORDER.

Using the Disc Menu & Title Menu

Some discs contain a dedicated menu system that allow you to select special functions for the title, such as chapters, audio tracks, subtitles, film previews, information on characters, etc.

For DVD-VIDEO discs

1 Press the DISC MENU button to enter the disc menu of the disc.

???Move to the setup menu related to the playback operation.

???You can select the audio languages and the subtitles provided by the disc.

Using the Search Functions

Searching through a Chapter or Track

2 Press the TITLE MENU button to move to the title menu of the disc.

???Use this button if the disc contains more than one title. Some type of discs may not support the title menu function.

For DVD-RW/-R discs

1 Press the TITLE LIST button to move to the Title List.

??? Title List: Title List shows a list to help

NOTE

you select a title. Since the title list consists of the information on video that is actually recorded, if one title is deleted, that title cannot be played again.

??? Playlist: This refers to a unit of playback, which is made by selecting a desired scene in the entire Title List. When one playlist is played,

layback

only the scene selected by the user will play and then stop.

NOTE

mode except Fast 1 mode.

Since only the information necessary for playing a desired scene is included in a playlist, even if that playlist is deleted, the original recording will not be deleted. (only VR mode)

???You cannot also hear during scanning MPEG4 in all mode.

???For CD(CD-DA), you can hear sound during Scan mode.

Playback

Skipping Chapters or Tracks

???During playback, you can search quickly through a chapter or track.

1 During playback, press the SKIP ( ) button on the remote control.

??? If you press the SKIP ( ) button,

it moves to the beginning of the chapter or track or marker(DVD-RW(VR mode)).

Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker(DVD-RW(VR mode)).

??? If you press the SKIP ( ) button,

it moves to the next chapter or track or marker (DVD-RW(VR mode)).

Slow Motion Play

???If you press the SEARCH() button,

Slow 1 ??? Slow 2 ??? Slow 3

???If you press the SEARCH( ) button,

Slow 1 ??? Slow 2 ??? Slow 3

???To return to normal speed playback, press the PLAY button.

Press and hold the SEARCH ( ) button during pause, the disc will play slowly at a Slow 1 speed. If the button is released, the pause operation will resume.

???The speed marked in this function may be different from the actual playback speed.

NOTE

???Slow motion operates only in the forward direction on MPEG 4 discs.

Step Motion Play

???

Press the STEP( ) button on the

1 remote control during playback or pause.

???Each time the button is pressed, a new frame will appear.

When STEP( ) is pressed, the previous frame will be activated.

When STEP( ) is pressed, the next frame will be activated.

???To return to normal speed playback, press the PLAY button.

???Step motion operates only in the forward

direction on MPEG 4 discs.

NOTE

About ANYKEY

The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter or time. You can also change the subtitle and audio

settings and set some features including Repeat, Angle, Zoom.

Moving to a scene directly using the ANYKEY

???If you want to move to a title, a chapter to find a desired scene.

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

2 Press the ?????? buttons to select Title or

Chapter.

DVD-VIDEO

MOVE CHANGE

3 Press the ?? ??? or number (0~9) buttons to select the desired scene.

Press the OK button.

???If you want to move to a desired time to help you find a scene.

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

2 Press the ?????? buttons to select Time.

DVD-VIDEO

3 Enter the time in the sequence of hours, minutes, seconds using the number buttons, then press the OK button.

??? This may not work for some discs.

NOTEWhen an audio CD(CD-DA) or an MP3 disc is inserted, according to a disc type,

the information display may not be appear.

???The Time Search function does not operate in some discs.

???To make the screen disappear, press the

ANYKEY again

Using the Repeat Function

Playing Repeatedly(Repeat Playback)

Using the REPEAT button

1 Press the REPEAT button during playback.

Repeat Off

2 Press the REPEAT or ?????? buttons to select Title or Chapter you want to play repeatedly. Press the OK button.

Repeat Title

Title : Repeats the title that is playing.

Chapter : Repeats the chapter that is playing.

- To return to normal playback -

3 Press the REPEAT buttons to select Off, then press the ?????? or REPEAT button and press OK button.

Press the CANCEL button to return to normal playback.

laybackP

Playback

Using the ANYKEY button

3 Press the OK button.

To make the screen disappear, press the ANYKEY or RETURN button. Repeat play allows you to repeat a title or chapter.

???DVD-RW(VR mode), unfinalised DVD-R and unfinalised DVD-RW (Video mode)

NOTE

do not repeat a chapter.

Playing a Certain section Repeatedly(A-B Repeat Playback)

Using the ANYKEY button

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

2 Press the ?????? buttons to select Repeat, then press the ??? button to select A-B.

DVD-VIDEO

MOVE OK

3 Press the OK button.

4 Press the OK button at the point where you want the repeat play to start (A), then press it again at the point where you want the repeat play to stop (B).

Repeat playback of the A-B section starts.

- To return to normal playback -

5 Select Off on the Repeat item or press the CANCEL button.

??? If you set point (B) before five seconds has lapsed, the prohibition mark ( ) will

???Audio CDs(CD-DA) and MP3 discs do not support the Repeat A-B function.

Selecting the Subtitle

Subtitle languages may not work depending on the disc type. This is only available during playback.

Using the SUBTITLE button

1 Press the SUBTITLE button during playback.

Subtitle Off

2 Press the SUBTITLE or ?????? buttons to select the desired subtitle language.

To make the screen disappear, press the CANCEL or RETURN button.

Selecting the Audio language

Audio languages may not work depending on the disc type. This is only available during playback.

Using the AUDIO button

1 Press the AUDIO button during playback.

2 Press the AUDIO or ?????? buttons to select the desired audio language.

Using the ANYKEY button

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

Using the ANYKEY button

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

laybackP

2 Press the ?????? buttons to select Subtitle, then press the ?? ??? buttons to select the desired subtitle language.

DVD-VIDEO

MOVE CHANGE

???The subtitle display may be different depending on the disc type.

NOTE

???If the subtitles overlap, disable the caption function on your TV.

???Some discs allow you to select the language for the disc menu only.

2 Press the ?????? buttons to select Audio, then press the ?? ??? buttons to select the desired audio language.

DVD-VIDEO

MOVE CHANGE

???Audio languages may be different depending on the disc type.

NOTE

???Some discs allow you to select the audio language for the disc menu only.

Playback

Changing the Camera Angle

When a DVD-VIDEO contains multiple angles of a particular scene, you can select the Angle function. This is only available during playback.

If the disc contains multiple angles, the ANGLE mark appears on the screen.

1 Press the ANYKEY button during playback.

DVD-VIDEO

MOVE CHANGE

2 Press the ?????? buttons to select Angle, then press the ?? ??? or number buttons to select the desired angle.

DVD-VIDEO

MOVE CHANGE

???This function is disc-dependent, may not work on all DVDs.

NOTE

???This function does not work when a DVD has not been recorded with a multi- camera angle system.

Zooming-In

1 Press the ANYKEY button during playback or pause.

DVD-VIDEO

MOVE CHANGE

2 Press the ?????? buttons to select Zoom, then press the OK button. ( ) will be displayed.

3 Press the ?????? ?? ??? buttons to move to the area you want to enlarge.

4 Press the OK button. The screen will be enlarged to twice the normal size.

If you press the OK button again after the screen was enlarged to twice the normal size, the screen size will be enlarged to four times the normal size.

normal size ??? 2X ??? 4X ??? 2X ??? normal size

Using Bookmarks

This feature lets you bookmark sections of a DVD-VIDEO or DVD-R/-RW(V mode), so you can quickly find them.

(V mode)

1 Press the MARKER button during playback.

Bookmark - - - - - - - - - --

2 Press the OK button when the desired scene appears.

The number 1 is displayed and the scene is memorized.

3 Press the ?? ??? button to move to the next position.

4 Press the OK button when the desired scene appears.

The number 2 is displayed and the scene is memorized.

???Repeat above to bookmark other positions.

???You can bookmark up to 10 scenes.

??? When the disc tray is opened and then

Playing back a bookmark

1 Press the MARKER button during playback.

2 Press the ?? ??? buttons to select a bookmarked scene.

3 Press the OK or PLAY button to start playing from the selected scene.

Clearing a bookmark

1 Press the MARKER button during playback.

2 Press the ?? ??? buttons to select a bookmarked scene.

Bookmark 1 2 - - - - - - - --

3 Press the CANCEL button to delete the selected bookmark.

laybackP

Using Markers

(VR mode)

1 Press the MARKER button during playback.

OK RETURN

Playing back a Marker

1 Press the MARKER button during playback.

2 Press the ?? ??? buttons to select a bookmarked scene.

Playback

2 Press the OK button when the desired scene appears.

The number 01 is displayed and the scene is memorized.

3 Press the ?? ??? button to move to the next position.

4 Press the OK button when the desired scene appears.

The number 02 is displayed and the scene is memorized.

???DVD-RW (VR Mode) discs have the Marker function instead of the Bookmark function. The Marker function allows you to mark up to 99 scenes. Since the scenes may be displayed as many different pages, numbering is necessary. If a disc in use is encoded with Disc Protection, Markers cannot be set or deleted. Only playback is available.

3 Press the OK or PLAY button to start playing from the selected scene.

???If you press the SKIP( ) button, it moves to the beginning of the marker. Pressing the button once again within 3 seconds returns to the beginning of the previous marker.

???If you press the SKIP( ) button, it moves to the next marker.

Clearing a Marker

1 Press the MARKER button during playback.

2 Press the ?? ??? buttons to select a bookmarked scene.

Press the CANCEL button to delete the selected bookmark.

???When a marker is cleared while DVD-RW (VR mode) is playing, marker numbers will change.

For example, if the 7th marker is cleared after ten markers are registered, the marker numbers after the eighth will automatically move ahead by one and the 8th marker becomes the 7th.

Playing an Audio CD/MP3

Playing an Audio CD (CD-DA)/MP3

Each disc has a variety of menu functions available.

Playing an Audio CD(CD-DA)

1 Insert an audio CD (CD-DA) into the disc tray.

The audio CD menu appears and the tracks (songs) are played automatically.

2 Press the ?????? buttons to select the track you want to hear, then press the OK or ??? button.

Buttons on the Remote Control used for Audio CD(CD-DA) playback

!

@ ! #

(

Audio CD(CD-DA) Screen Elements

1.Play mode icon

2.Current track(song)

3.Displays the current play index and total track number.

4.Shows the operating state of a disc and a playback time corresponding to a portion that is currently played.

5.Displays the track list(song list) and the playing time of each track.

6.Button display.

1.?????? : Selects a track (song).

2.??? : Plays the selected track (song).

3.OK button: Plays the selected track (song).

4.SKIP( ) button: Plays the next track.

5.SKIP( ) button: Returns to the beginning of the current track when pressed during playback. If pressed again, your DVD recorder moves to and plays the previous track.

If you press the this button within three seconds after playback starts, the previous track will be played.

If you press the this button after three seconds, the current track will be replayed from the beginning.

6.Press the SEARCH( / ) button: Fast Play (X2, X4, X8)

7.STOP button: Stops a track(song).

8.PLAY/PAUSE button: Plays a track(song) or pauses playback.

9.ANYKEY button: Selects the sub menu on screen display (Repeat or Play Option).

laybackP

Playback

1 Insert an MP3 Disc into the disc tray.

2 Press the ?????? buttons to select Disc Navigation, and then press the OK or ??? button.

3 Press the ?????? buttons to select Music, then press the OK or ??? button.

The MP3 menu appears and the tracks(songs) are played automatically.

4 Press the ?????? buttons to select the track (song) you want to hear, then press the OK or ??? button.

1.Play mode icon

2.Current track (song)

3.Displays the current track(song) information.

4.Shows the operating state of a disc and a playback time corresponding to a portion that is currently played.

5.Displays the information for the folder and its tracks.

6.Button display.

Buttons on the Remote Control used for MP3 playback

^ %

& *

@ ! #

(

1.?????? : Selects a track (song).

2.??? : Plays the selected track (song).

3.OK button: Plays back the selected track (song) or displays the files in the selected folder.

4.RETURN button: Moves to the folder to which the current song belongs.

5.SKIP( ) button: Plays the next track.

6.SKIP( ) button: Returns to the beginning of the current track when pressed while playing. If pressed again, your DVD recorder moves to and plays the previous track.

If you press the this button within three seconds, the previous track will be played.

If you press the this button after three seconds, the current track will be replayed from the beginning.

7.STOP button: Stops a track(song).

8.PLAY/PAUSE button: Plays a track(song) or pauses playback.

9.ANYKEY button: Selects the sub menu on screen display (Repeat or Play Option).

Playing Repeatedly(Repeat Playback)

Using the REPEAT button

1 Press the REPEAT button during playback.

The Track repeat mode icon ( ) appears and the selected track is played repeatedly.

2 Press the REPEAT button once more to play the disc repeatedly.

The Disc repeat mode icon ( ) appears and the inserted disc is played repeatedly.

For MP3 disc, the Folder repeat mode icon( ) appears and all tracks in the current folder are played repeatedly.

Pressing the REPEAT button once more changes the mode to the Disc repeat mode.

To return to normal playback

3 Press the REPEAT button repeatedly until the repeat mode icon disappears, or press the CANCEL button.

laybackP

Playback

Using the ANYKEY button

1 Press the ANYKEY button during playback.

The PLAY MODE window appears.

2 Select the desired repeat mode (Track or Disc) using ?? ??? buttons, and then press the OK button.

For MP3 discs, you can select Track, Folder or Disc.

To return to normal playback

3 Select Off in the PLAY MODE window using the ?? ??? buttons, and then press the OK button.

Play Option Mode

The Play Option can be used with an audio CD or MP3 in Stop mode.

1 Press the ANYKEY button in Stop mode.

The PLAY MODE window appears.

2 Press the ?? ??? buttons to select the desired item (Normal, Random, Intro or Playlist) in the Play option, then press the OK button.

???Normal: Tracks on a disc are played in the order in which they were recorded on the disc.

???Intro: The first 10 seconds of each track will be played. If you want to listen to the music that you have selected, press the OK or PLAY button. The play option will be changed to Normal Play. When Intro Play is completed, Normal Play is performed.

???Playlist: The Playlist playback option allows you to select the order in which you want tracks to play.

???Random: The Random option plays a disc???s tracks in random order. After a random list is generated and played completely, another random list is generated and played. Random Play is continued until the play option is changed.

To Programme Tracks

You can register a maximum of 30 tracks in the playlist.

1 Press the ANYKEY button in Stop mode.

The PLAY MODE window appears.

2 Press the ?? ??? buttons to select Playlist in the Play option.

4 If you playlisted a wrong track, press the ??? button, then press the ?????? buttons to select the wrong track, then press the CANCEL button.

The wrong track will be removed.

5 Press the PLAY button to playback the playlist.

Playing a Picture

1 Insert a JPEG into the disc tray.

2 Press the ?????? buttons to select Disc Navigation, and then press the OK or ??? button.

3 Press the ?????? buttons to select Photo, and then press the OK or ??? button.

4 Press the ?????? ?? ??? buttons to select a picture.

??? To see the next 8 pictures, press the SKIP( ) button.

???To see the previous 8 pictures, press the SKIP( )button.

Playback

5-1 If you press the PLAY button, the Slide Show Speed screen will appear.

Press the ?? ??? buttons to set the slide show speed, then press the OK button.

5-2 Press the OK button with a picture selected in the Album screen. And select a display mode (Album screen, Slide show, Rotation or Zoom) using the ?? ??? buttons, then press the OK button.

: Returns to the Album screen.

: The DVD Recorder enters slide show mode. Before the slide show can begin, the picture interval (Slide show speed) must be set.

: Each time the OK button is pressed, the picture rotates 90 degrees clockwise.

: Each time the OK button is pressed, the

picture is enlarged up to 4X(Four times the normal size).

(Normal ??? Zoom X2 ??? Zoom X4 ??? Zoom X2 ??? Normal)

???Press the ANYKEY button to display the menu bar.

???Press the RETURN button to clear the menu bar.

Playing a MPEG4

MPEG4 File is used to contain the audio and video data.

MPEG4 File with following extensions can be played. - .AVI, .DIVX, .avi, .divx

1 Insert a MPEG4 Disc into the disc tray.

2 Press the ?????? buttons to select Disc Navigation, and then press the OK or ??? button.

3 Press the ?????? buttons to select DivX, and then press the OK or ??? button.

4 Press the ?????? buttons to select the avi file (DivX), then press the OK, ??? or PLAY button.

5 When MPEG4 file is played, you can use following functions.

Pressing the STOP button once during playback will display the file list, pressing the button again will exit the menu screen.

MPEG4 Function Description

Playing the Title List

Follow these instructions to play back a scene from the Title List.

??? This DVD Recorder can play the following NOTE video compression formats.

-MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x DivX-Pro Xvid

-Motion Compensation : QPEL, GMC

-Audio format : ???MP3???, ???MPEG1 Audio Layer2???, ???LPCM???, ???AC3???, ???DTS???, ???MS ADPCM???

???Supported subtitle file formats: .smi, .srt,

.sub, .psb, .txt, .ass (The subtitle file should have exactly the same name to corresponding MPEG4 file name)

???Some MPEG4 files created on a personal computer may not be play back.

That is why Codec Type, Version and Higher resolution over specification is not supported.

Using the TITLE LIST button

1 Press the TITLE LIST button.

The Title List screen is displayed.

2 Press the ?????? buttons to select an entry you want to play from Title List, then press the PLAY button.

The selected entry (title) will be played back.

3 To stop title play, press the STOP button.

To return the title list screen, press the TITLE LIST button.

laybackP

Using the MENU button

1 Press the MENU button.

2 Press the ?????? buttons to select Title List, then press the OK or ??? button twice.

The Title List screen is displayed.

3 Press the ?????? buttons to select an entry you want to play from Title List, then press the OK or ??? button.

The Edit menu is displayed on the right.

(Rename, Delete, Edit, Protection : See pages 69-72)

4 Press the ?????? buttons to select Play to play the title list, then press the OK button.

The selected entry (title) will be played back.

??? Play

Playback

To view the current status of the disc and progress of playback : Press the INFO button, the information about the disc will appear.

Press the INFO button once again. Then you can check the information about the title under playback.

5 To stop title play, press the STOP button.

To return the title list screen, press the TITLE LIST button.

??? You can also play a recorded programme NOTEby pressing the ANYKEY button during

playback.

DVD-RW(VR)

MOVE CHANGE

???Press the ?????? buttons to select Title.

???Press the ?? ??? buttons to select to play the title list, then press the OK button.

Editing

Editing

This section introduces basic functions of DVD editing and explains both edit functions for the recording on a disc and edit functions for the entire disc.

???Title List

A title is a section of recorded video and audio. Title List shows a list to help you select a title. Since the title list consists of the information on

stream that is actually recorded, if one title is deleted, that title cannot be played again.

???Playlist

This refers to a unit of playback, which is made by selecting a desired scene in the entire Title List. When one playlist is played, only the scene selected by the user will play and then stop. Since only the information necessary for playing a desired scene is included in a playlist, even if that playlist is deleted, the original stream will not be deleted.

Recording or editing might not be completed if an error, such as a sudden power failure occurs.

Please be aware that a material that has been damaged is unable to be retrieved to its original content.

Basic Editing (Title List)

Renaming(Labeling) a Title

Follow these instructions to rename a title list entry, i.e., to edit the title of a recorded programme.

Using the TITLE LIST button

1 Press the TITLE LIST button.

The Title List screen is displayed

Using the MENU button

???Press the MENU button.

???Press the ?????? buttons to select Title List, then press the OK or ??? button twice.

2 Press the ?????? buttons to select an entry you want to rename from the Title List, then press the OK or ??? button.

3 Press the ?????? buttons to select Rename, then press the OK button.

The Rename screen is displayed.

4 Press the ?????? ?? ??? buttons to select the desired characters, then press the OK button.

??? Back Space: Deletes the character before the cursor.

???Space: Enters a blank and moves the cursor one forward (to the right).

???Delete: Deletes the character at the cursor position.

???Clear: Deletes all the character inputs.

???Save: Registers the character inputs.

5 Press the ?????? ?? ??? buttons to select Save, then press the OK button.

The changed title name is displayed on the title item of the selected entry.

ditingE

Editing

Locking(Protecting) a Title

Follow these instructions to lock an entry to protect it from accidental deletion.

Using the TITLE LIST button

1 Press the TITLE LIST button.

The Title List screen is displayed

Using the MENU button

???Press the MENU button.

???Press the ?????? buttons to select Title List, then press the OK or ??? button twice.

2 Press the ?????? buttons to select an entry you want to protect in the Title List, then press the OK or ??? button.

3 Press the ?????? buttons to select Protection, then press the OK or ??? button.

4 Press the ?? ??? buttons to select On, then press the OK button. The key icon on the information window for the selected entry changes to the locked status. ( ??? )

Deleting a Title

Follow these instructions to delete an entry from the Title List.

Using the TITLE LIST button

1 Press the TITLE LIST button.

The Title List screen is displayed

Using the MENU button

???Press the MENU button.

???Press the ?????? buttons to select Title List, then press the OK or ??? button twice.

2 Press the ?????? buttons to select an entry you want to delete in the Title List, then press the OK or ??? button.

3 Press the ?????? buttons to select Delete, then press the OK or ??? button.

You will be prompted with a confirmation message.

DVD-RW(VR mode): Since Playlist is present, the message ???Do you want to delete? (Related playlists may be deleted.)??? is displayed.

DVD-RW(Video mode), DVD-R: Since Playlist is not present, the message ???Do you want to delete???? is displayed.

??? The message may depend on the type of disc.

4 Press the ?? ??? buttons to select Yes, then press the OK button.

??? You cannot delete a protected entry.

NOTEIf you want to delete a protected entry, select ???Off??? in the Title Protection menu.

(See page 70)

???When the Disc Protection has been set to Protected, you cannot delete titles.

(See page 82 )

???Once an entry is deleted from the Title List it cannot be recovered.

???Once DVD-R, DVD-RW is finalised, it cannot be deleted.

???With DVD-R, titles are only deleted from the menu however, the Title remains physically on the disc.

Deleting a Section of a Title

Follow these instructions to delete a section of a Title List entry.

(VR mode)

Using the TITLE LIST button

1 Press the TITLE LIST button.

The Title List screen is displayed

Using the MENU button

???Press the MENU button.

???Press the ?????? buttons to select Title List, then press the OK or ??? button twice.

2 Press the ?????? buttons to select an entry you want to edit from the Title List, then press the OK or ??? button.

3 Press the ?????? buttons to select Edit, then press the OK or ??? button.

The Edit Title List screen is display

ditingE

1.Playback bar

2.Playtime

3.Section deletion starting point window and time

4.Section deletion end point window and time

???Select the start and end points of the section you want to delete using the playback related buttons.

???Playback related buttons: ( , , , , ).

5 Press the OK button at the end point.

The image and end point time are displayed in the Section deletion ending point window.

???If the end time precedes the starting point, you will be prompted with the message ???End point cannot be marked earlier than start point???.

???The section cannot be deleted when it includes a still picture.

???Press the MENU button after the operation has finished. The Edit Title List screen will disappear.

Advanced Editing (Playlist)

Creating a Playlist

Follow these instructions to create a new playlist entry from a recorded title.

(VR mode)

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Playlist, then press the OK or ??? button.

3 Press the ?????? buttons to select New Playlist, then press the OK or ??? button.

The Make Scene screen is displayed.

4 Press the OK button at the start point.

???The image and time at the start point are displayed on the Start window.

???The yellow-coloured selection bar moves to the End item.

???Select the starting point of the section from which you want to create a new scene using the

playback related buttons ( , , , , ,

, ).

5 Press the OK button at the end point.

???The image and end point time are displayed in the End window.

???The yellow-coloured selection bar moves to the Make item.

-To make a new playlist -

6 Press the OK button at the Make item.

A new Scene will be added to the current Playlist. A new Make Scene screen is displayed.

???You can check and see all the scenes on Edit Playlist screen.

NOTE

???Repeat steps 1~6 if you want to make a new playlist.

???Repeat steps 4~6 if you want to make scenes of the playlist.

-To return to Edit Playlist menu -

7 Press the ?? ??? buttons to select Return, then press the OK button.

The Edit Playlist screen is displayed.

8 Press the MENU or PLAY LIST button after the operation has finished.

The Edit Playlist screen will disappear.

??? You can create up to 99 playlist entries.

ditingE

Editing

Playing Entries in the Playlist

Follow these instructions to play the playlist entries.

(VR mode)

1 With the DVD Recorder in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed.

Using the MENU button

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Playlist, then press the OK or ??? button.

???Press the ?????? buttons to select Edit Playlist, then press the OK or ??? button.

2 Press the ?????? buttons to select the title you want to edit from the Playlist, then press the OK or ??? button.

The Edit Playlist menu is displayed : Play, Rename, Edit Scene, Copy, Delete.

3 Press the ?????? buttons to select Play, then press the OK button.

??? Play

???To view the current status of the disc and progress of playback : Press the INFO button, and the information about the disc will appear.

???Press the INFO button once again. Then you can check the information about the playlist currently playing back.

???The screen returns to the Edit Playlist screen when the playback has finished.

4 Press the STOP button to stop playing.

The screen returns to the Edit Playlist screen.

Renaming a Playlist Entry

Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry.

(VR mode)

1 With the DVD Recorder in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed.

Using the MENU button

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Playlist, then press the OK or ??? button.

???Press the ?????? buttons to select Edit Playlist, then press the OK or ??? button.

2 Press the ?????? buttons to select the title you want to edit from the Playlist, then press the OK or ??? button.

The Edit Playlist menu is displayed : Play, Rename, Edit Scene, Copy, Delete

3 Press the ?????? buttons to select Rename, then press the OK button.

The Rename screen is displayed.

4 Enter the desired characters using the ?????? ?? ??? buttons.

???This function is the same as the Rename function in renaming the title list. (See page 69.)

???The maximum number of characters that can be entered is 31. All 31 characters can be

displayed by pressing the INFO button twice.

5 Press the ?????? ?? ??? buttons to select Save, then press the OK button.

The changed title is displayed in the title field of the selected playlist entry.

ditingE

Editing

Editing a Scene for the Playlist

Follow these instructions to edit scenes for a playlist.

(VR mode)

1 With the DVD Recorder in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed.

Using the MENU button

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Playlist, then press the OK or ??? button.

???Press the ?????? buttons to select Edit Playlist, then press the OK or ??? button.

2 Press the ?????? buttons to select the title you want to edit from the Playlist, then press the OK or ??? button.

The Edit Playlist menu is displayed : Play, Rename, Edit Scene, Copy, Delete

3 Press the ?????? buttons to select Edit Scene, then press the OK button.

The Edit Scene screen is displayed.

Playing a Selected Scene

4 Press the ?????? ?? ??? buttons to select the scene you want to play, then press the OK button.

The playlist entry to be played is selected.

5 Press the OK button.

The selected scene is played.

??? Play

??? To stop scene play, press the STOP button.

Modifying a Scene (Replacing a Scene)

To setup, follow steps 1 to 3 in page 76.

4 Press the ?????? ?? ??? buttons to select the scene you want to modify, then press the OK button.

5 Press the ?????? buttons to select Modify, then press the OK button.

The Modify Scene screen is displayed.

6 Press the OK button at the start point of the scene.

???The image and starting point time are displayed on the Start window.

???Select the starting or ending point of the section you want to modify using the playback related buttons ( , , , , , , ).

7 Press the OK button at the end point of the scene.

???The image and ending point time are displayed in the End window.

8 Press the ?? ??? buttons to select Change, then press the OK button.

???The scene you want to modify is changed with the selected section.

Editing

???A yellow selection window is displayed on the scene to be moved.

6 Press the ?????? ?? ??? buttons to select the position to which you want to move the selected scene, then press the OK button.

???The selected scene is moved to the selected position.

6 Press the OK button at the starting point of the scene.

???The image and starting point time are displayed in the Start window.

???Select the end point of the section where you want to add the new scene using the playback related buttons ( , , , , ).

7 Press the OK button at the end point of the scene.

???The image and time of the end point are displayed in the End window.

???To cancel, press the ?? ??? buttons to select cancel, then press the OK button.

???The section you want to add is inserted prior to the scene selected in step 4.

Deleting a Scene

To setup, follow steps 1 to 3 in page 76.

4 Press the ?????? ?? ??? buttons to select the scene you want to delete, then press the OK button.

5 Press the ?????? buttons to select Delete, then press the OK button.

Add

Copying a Playlist Entry to the Playlist

Using the PLAY LIST button

1 With the DVD Recorder in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed.

Using the MENU button

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Playlist, then press the OK or ??? button.

???Press the ?????? buttons to select Edit Playlist, then press the OK or ??? button.

2 Press the ?????? buttons to select the title you want to copy to the Playlist, then press the OK or ??? button.

The Edit Playlist menu is displayed :Play, Rename, Edit Scene, Copy, Delete

3 Press the ?????? buttons to select Copy, then press the OK button.

Playlist that has been selected will be copied.

ditingE

??? You can create up to 999 scenes on one

3 Press the ?????? buttons to select Delete, then press the OK button.

NOTE

disc. In some cases, this may be different from the actual numbers.

Editing

???Press the MENU button after the operation has finished. The Edit Playlist screen will disappear.

Deleting a Playlist Entry from the Playlist

Using the PLAYLIST button

1 With the DVD Recorder in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed.

Using the MENU button

???With the DVD Recorder in Stop mode, press the MENU button.

???Press the ?????? buttons to select Playlist, then press the OK or ??? button.

???Press the ?????? buttons to select Edit Playlist, then press the OK or ??? button.

2 Press the ?????? buttons to select the title you want to delete from the Playlist, then press the OK or ??? button.

The Edit Playlist menu is displayed : Play, Rename, Edit Scene, Copy, Delete

???You will be prompted with the delete confirmation message ???Do you want to delete????.

4 Press the ?? ??? buttons to select Yes, then press the OK button.

It automatically returned to the Edit Playlist screen after the delete operation has finished.

Disc Manager

Editing the Disc Name

Follow these instructions to give a name to a disc.

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

4 Enter the desired characters using the ?????? ?? ??? buttons.

???This function is the same as the Rename function in renaming the title list. (See page 69.)

???The maximum number of characters that can be entered is 31. All 31 characters can be

displayed by pressing the INFO button.

5 Press the ?????? ?? ??? buttons to select Save, then press the OK button.

A disc name is given to the disc.

???Depending on the kind of disc, the displayed screen may be different.

DVD-RW(VR)

ditingE

Editing

Disc Protection

Disc Protection allows you to protect your discs from being formatted or deleted due to unintended operations.

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

DVD-RW(VR)

3 Press the ?????? buttons to select Disc Protection, then press the OK or ??? button.

4 Press the ?????? button to select Protected, then Press the OK button.

Formatting a Disc

Use these instructions to format a disc.

The disc protect should also be cleared.

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

3 Press the ?????? buttons to select Disc Format, then press the OK or ??? button.

DVD-RW

???You will be prompted with the confirmation message ???Choose the recording format for

4 Press the ?? ??? buttons to select desired mode, then press the OK button.

???You will be prompted again with the message ???All data will be deleted. Do you want to continue????.

5 Press the ?? ??? buttons to select Yes, then press the OK button.

The disc is formatted.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

3 Press the ?????? button to select Delete All Title Lists, then press the OK or ??? button.

DISCDVD-RW

DVD-RW

DVD-R

DVD-VR and DVD-V are defined according to their recording format.

Delete All Title Lists

1 With the DVD Recorder in Stop mode, press the MENU button.

???You will be prompted with the confirmation message ???Do you want to delete all title lists????.

???When Protected Entry exists: The Delete All Title List function will not operate. If there is a title containing a still picture, however, that function will not operate. If you want to delete a protected entry, disable Protect for it on the Lock item.

4 Press the ?? ??? buttons to select Yes, then press the OK button.

All title lists are deleted.

Editing

Finalising a disc

After you record titles onto a DVD-RW/DVD-R disc with your DVD recorder, it needs to be finalised before it can be played back on external devices.

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

3 Press the ?????? button to select Disc Finalise, then press the OK or ??? button.

You will be prompted with the message ???Do you want to finalise disc????.

If you select Yes, you will be prompted again with the message ???Disc will be finalised. Do you want to continue????.

4 Press the ?? ??? buttons to select Yes, then press the OK button.

The disc is finalised.

??? Once a disc is finalised, you cannot

Unfinalising a disc (V/VR mode)

1 With the DVD Recorder in Stop mode, press the MENU button.

2 Press the ?????? buttons to select Disc Manager, then press the OK or ??? button.

3 Press the ?????? button to select Disc Unfinalise, then press the OK or ??? button.

You will be prompted with the message ???Do you want to unfinalise disc????.

If you select Yes, you will be prompted again with the message ???Disc will be unfinalised. Do you want to continue????.

4 Press the ?? ??? buttons to select Yes, then press the OK button.

The disc is unfinalised.

??? A DVD-RW can be finalised or unfinalised

???A DVD-RW can be finalised or unfinalised in VR mode.

ditingE

Additional

Information

Troubleshooting

If your DVD Recorder malfunctions, go through the checkpoints below before contacting a Samsung autho- rised service centre.

Power

The input is displayed for a while when the power is turned on.

Checkpoint 1 The DVD recorder requires some time to initialize and the input will be displayed for approx. 10 seconds after it is turned on.

Recording

Cannot record TV programmes.

Checkpoint 1

Checkpoint 2

Checkpoint 3

Check whether the power cord is securely plugged into the power outlet.

Did you set the DVD recorder channel settings correctly?

Check the free space on your DVD-RW/DVD-R discs.

Additional Information

I pressed the REC button but there is no response.

Checkpoint 1 Recording is possible for DVD-RW/ DVD-R discs only.

If a programme is copy protected, it cannot be recorded.

Playback

Cannot play the disc.

The angle operation does not work while playing a DVD disc.

Checkpoint 1

Checkpoint 2

Checkpoint 3

Check whether the disc is inserted correctly with the label facing up.

Check the regional code of the DVD disc.

This DVD recorder cannot play some types of discs. (See pages 5, 49.)

Checkpoint 1 The angle operation is available only when the disc contains images captured from different angles.

icon appears on the screen.

Checkpoint 1 You cannot use this operation or function due to one of the following reasons:

(1)Your DVD disc restricts it.

(2)Your DVD disc does not support this feature (for example: angles)

(3)The feature is not available at the moment.

(4)You've requested a title, chapter, or scan time that is out of range.

The selected audio and/or subtitle language is not played.

Checkpoint 1 Audio and subtitle languages are disc-specific. Only the sound and subtitle languages contained on the DVD disc are available and displayed in the disc menu.

Play mode settings are different from the settings configured in the Settings menu.

Checkpoint 1 The disc does not support all selected functions. In this case, some settings configured in the settings menu may not work properly.

Cannot change the aspect ratio.

Checkpoint 1 The aspect ratio is fixed for DVD discs. (See page 36)

Information dditionalA

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 4

Be sure that the Video Setting is properly set. (See pages 34-36)

Check whether there is damage to or any foreign material on your disc.

Some low quality discs may not play properly.

If scenes change from dark to bright suddenly, the screen may shake vertically temporarily, but this is not a fault.

Checkpoint 1 Check there is enough space in the disc for recording.

Checkpoint 2 Check whether the current disc is recordable or not.

Make sure to check before the start time of recording.

Timer recording does not work properly.

Sound

Checkpoint 1 Re-check the recording time and the end time settings again.

No sound.

Checkpoint 1

Are you watching a programme in slow or skip mode?

If you are playing a programme at a speed other than normal or fast 1 speed, sound will not be heard.

Checkpoint 2

Checkpoint 3

Checkpoint 4

Check the connections and settings. (See pages 21-22, 32-33)

Check whether the disc is damaged. Clean the disc, if necessary.

Check whether the disc is inserted correctly with the label facing up.

Additional Information

No audio output.

Checkpoint 1 Check whether you have selected the correct digital output options in the Audio Output Options menu.

(See page 33.)

Remote Control Unit

The remote control doesn't work.

Other problems.

Checkpoint 1 Point the remote control at the remote control sensor on your DVD recorder. Allow for proper distance. Remove obstacles between your DVD recorder and the remote control.

Checkpoint 2 Check whether the batteries are empty.

Checkpoint 3 Check for the TV/DVD selection button.

Checkpoint 1

Checkpoint 2

Checkpoint 3

Read the table of contents and then find and read the section describing your problem, follow the instructions given.

Turn your DVD recorder off and on.

If the problem still persists, contact a nearby Samsung service centre.

Checkpoint 1

Press and hold down the PROG ( ) buttons on the front panel of the DVD Recorder simultaneously for more than 5 seconds with no disc in the DVD Recorder. All settings including the password will revert to the factory settings. Do not use this unless absolutely necessary. (Note that this function is possible only when no disc is inserted.)

Checkpoint 1

A recorded disc is played with only the subtitle and the audio signal which were selected during recording.

Additional Information

For DVD discs, audio signals recorded at 96kHz sampling Audio Output frequency are converted and output at 48kHz.

ELLAS (GREECE)

Agaphtevpelavth,

Sa?? eucaristouvme gia thn empistosuvnh pou deivxate sthn SAMSUNG me thn agoravauthv?? th?? suskeuhv??. To proiovn autovth?? SAMSUNG eivnai egguhmevno gia perivodo dwvdeka (12) mhnwvn apovthn hmeromhniva ago- rav?? tou gia antallaktikavkai ergatikav.Sthn perivptwsh pou qa creiasteivepiskeuhv, to proiovn autov th?? SAMSUNG qa prevpei na staleivhvna metaferqeiv sto exousiodothmevno service, me evxoda tou agorasthv. Exousiodothmevnoi antiprovswpoi kai exousiodothmevna kevntra service se avlle?? Eurwpaikev?? cwvre??, qa apodecqouvn tou?? ovrou?? th?? egguvhsh??.

Plhroforive?? gia ta exousiodothmevna kevntra service sthn Ellavda, mporeivte na pavrete apovthn

FOURLIS TRADE A.E.B.E.

L. Kruonerivou 112

145 68 Kruonevri, Apikhv??

Thl. 210.629.3100

??? Oroi th?? egguvhsh??

1.H egguvhsh iscuvei eavn kai movno eavn to proiovn creiavzetai service kai h kavrta egguvhsh?? evcei plhvrw?? sumplhrwqeivkai sfragisqeivapovto katavsthma agorav??. Epivsh?? prevpei na proskomisqeiv kai to timolovgio hvh apovdeixh lianikhv?? pwvlhsh??, pavnw sthn opoiva o seiriakov?? ariqmov?? tou proiovn- to?? prevpei na eivnai eukrinhv??.

2.H upocrevwsh th?? SAMSUNG aforavmovno thn episkeuhvtou proiovnto??

3.H episkeuhvtou proiovnto?? prevpei na anativqetai movno se exousiodothmevna kevntra service hv exousiodothmevnou?? antiproswvpou?? th?? SAM- SUNG. Kamiva apozhmivwsh den qa givnei apodekthv gia episkeuhvpou evcei givnei apovmh exousiodoth- mevno apovthn SAMSUNG sunergeivo.

4.To proiovn autovden qa qewrhqeivellatwmatikovsta ulikavhvsthn ergasiva episkeuhv?? eavn qa prevpei na prosarmosteiv, metatrapeivhvruqmisteivwvste na summorfwqeivme ti?? topikev?? tecnikev?? prodia- grafev?? hvprodiagrafev?? pou iscuvoun se cwvra avllh apovauthvgia thn opoiva proorizovtan hv kataskeuavsthke.

H egguvhsh authvden kaluvptei apozhmiwvsei?? gia??

*Kefalev?? bivnteo kai kasetofwvnwn

*Kefalev?? binteokavmera??

*Gennhvtrie?? aktinwvn Iaser sta CD, DVD

*Thleceiristhvria

*Lucnive?? fouvrnwn mikrokumavtwn

*Prosarmogev??, metatropev?? hvruqmivsei??, anex- avrthta an eivnai epituchv?? hvanepituchv??, ouvte opoiadhvpote zhmiva proevrcetai ex autouv...

5.H egguvhsh authvden kaluvptei kamiva apovti?? parakavtw periptwvsei????

*Periodikouv?? elevgcou??, sunthvrhsh kai episkeuhv hvantikatavstash merwvn pou ofeivlontai se fusiologikhvfqorav

*Ta evxoda kai tou?? kinduvnou?? metaforav?? pou scetivzontai me thn egguvhsh autouvtou proiovn-

to??

*Zhmiva se autovto proiovn pou proevrcetai apov??

A.Katavcrhsh hvkai kakhvcrhvsh, sumperilam- banomevnh?? allavkai mh periorismevnh?? se?? Mh crhvsh autouvtou proiovnto?? gia tou?? skopouv?? pou fusiologikavproorivzetai hvsuvm- fwna me ti?? odhgive?? crhvsew?? gia thn swsthv crhvsh kai sunthvrhsh autouvtou proiovnto?? Thn egkatavstash kai crhvsh tou proiovnto?? me trovpou?? pou antivkeintai sti?? tecnikev?? prodiagrafev??

asfaleiva?? pou iscuvoun katavthn crhvsh tou proiovnto??

B.Episkeuhvpou evgine apovmh exousiodothmevna sunergeiva service

G.Atuchvmata, qeomhnive?? hvopoiadhvpote aitiva pevra tou elevgcou th?? SAMSUNG, sumperil- ambanomevnwn allavmh periorismevnwn twn keraunwvn, tou nerouv, th?? fwtiav??, twn dhmo- sivwn anataracwvn, tou kakouvaerismouvklp.

D.H egguvhsh authvden ephreavzei ta dikaiwvma- ta tou katanalwthvpou

problevpontai apovthn efarmosteva eqnikhv nomoqesiva pou iscuvei, ouvte ta dikaiwvmata twn katanalwtwnv enantivon twn lianopwl- htwnv pou aporrevoun apovthn suvmbash pwvlhsh??.

E.Se perivptwsh pou den upavrcei eqnikhvnomo- qesiva authvh egguvhsh qa eivnai h monadikhv kai apokleistikhvkavluyh tou katanalwthvgia kavqe zhmiav.

FOURLIS TRADE A.E.B.E.