OWNER'S MANUAL
AND INSTALLATION GUIDE
DETACHABLE FRONT PANEL AM/FM/MPX RADIO
WITH
CD CHANGER CONTROLS AND QUARTZ CLOCK
OWNER'S MANUAL
AND INSTALLATION GUIDE
DETACHABLE FRONT PANEL AM/FM/MPX RADIO
WITH
CD CHANGER CONTROLS AND QUARTZ CLOCK
INSTALLATION INSTRUCTIONS
2
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1.Remove the detachable front panel if it is attached to the chassis by pushing the ???Release??? button. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2.Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3.Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.
4.Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must be ???on???). If unit does not operate, re- check all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.
5.Carefully slide the radio into the mounting sleeve making sure it is
6.Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration.
7.
INSTALLATION USING KITS
1.If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.
2.Wire and test the radio as described in Step 4 above.
3.Install the radio/mounting plate assembly to the
4.Attach the support strap to the radio and dashboard as described in Step 6 above.
5.Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.
1.Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.
2.Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3.Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION : DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
4.Wire the new radio to the vehicle as per step 4 of the Universal Installation Procedure.
5.Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
EXISTING DASH OPENING (FILE EDGES TO FIT IF
NOTE: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
IONSTINSTRUC IONTAALLINST
3
WIRING
RADIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
RADIO
AUTOMATIC
ANTENNA ANTENNA
EXISTING
ANTENNA
CABLE
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED TO
REMOTELY ACTIVATE AN AUTO-
MATIC ANTENNA OR AN EXTERNALFUSEBLOCK
AMPLIFIER (SEE ANTENNA OR AM-
PLIFIER MANUAL)
IMPORTANT
YELLOWWIREMUSTBECONNECTEDASSHOWN
OR RADIO WILL NOT OPERATE PROPERLY
YELLOW
FILTER/FUSE
BOX
4 PIN PLUGS
POSITIVE (+) TERMINAL 12V BATTERY
ANTENNA PLUG
9 PIN PLUG
(SEE PAGE 5 FOR SPEAKER WIRING)
ANTENNA SOCKET
4
RADIO
NOTE:
ERKASPE
RCA JACKS
LINE OUT
FOR USE WITH
OPTIONALRADIO
EXTERNAL
AMPLIFIERS
CALL
OF MODEL CHANGERS THAT WILL WORK WITH
YOURRADIO.
DIN CABLE (SUPPLIED OPTIONAL CD CHANGER
WIRING
RED = RIGHT
WHITE = LEFT
WITH CD CHANGER).
6
LEFT FRONT SPEAKER
HELP!
LEFT REAR SPEAKER
5
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
6
1
Press this button to turn the unit on and off when the ignition switch is on. When the unit is off, the Liquid Crystal Display (LCD) panel will normally display the
2 VOLUME LEVEL CONTROL
To increase the volume level, rotate the PUSH SELECT- VOL control clockwise (CW). The volume will increase and the level will be shown on the display panel from a minimum of 00 to a maximum of 100. To decrease the volume level, rotate the PUSH SELECT control counter- clockwise (CCW). The volume will decrease as shown on the display panel. This control also includes the Select button 3 for adjustment of the bass, treble,
balance and fader levels as described in 4, 5, 6, and
7.
3 SELECT BUTTON (SEL)
This button is used to select the audio function (bass, treble, balance, or fade) to be adjusted using the Volume Level control 2. Pressing the Select button once will set the unit for volume adjustment (VOL will appear on the display panel). Pressing the button additional times will select bass adjustment (BAS on display), treble (TRB), balance (BAL), or fader (FAD). The display will
automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated.
4 BASS CONTROL
To adjust the bass level, first select the Bass mode by pressing the PUSH SELECT button 3 so the BAS indication appears on the display panel. Within 5 seconds of choosing the Bass mode, rotate the Volume Level control 2 CCW or CW to adjust the bass response as desired. The level will be shown on the display panel from a minimum
NOTE: If the BAS or TRE functions are set while the Equalizer function (EQ) is active, the Equalizer function will automatically revert to the FLAT setting.
5 TREBLE CONTROL
To adjust the treble level, first select the Treble mode by pressing the PUSH SELECT button 3 so the TRB indication appears on the display panel. Within 5 seconds of choosing the Treble mode, roatate the Volume Level control 2 CCW or CW to adjust the treble response as desired. The level will be shown on the display panel from a minimum of
6LEFT/RIGHT BALANCE CONTROL
To adjust the
7FRONT/REAR FADER CONTROL
To adjust the
8 LOUDNESS CONTOUR (LOUD)
When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press and hold the BAND/LOUD button to activate this feature and the indication LOUD ON will appear on the display panel for 5 seconds. Press and hold the button again to deactivate the feature, and LOUD OFF will appear on the display panel for 5 seconds.
9AUDIO MUTE SELECTOR (MUT)
Press this button momentarily to mute the volume from the system (MUTE will appear flashing on the display panel). Pressing this button again, adjusting the Volume Level control 2, or pressing any other button, will return to the volume level setting in use before the Mute function was activated.
bl AM/FM BAND SELECTOR (BAND)
Each time the BAND/LOUD button is pressed, the radio band is changed. The indications F1, F2, F3 or AM will appear in the display panel according to your selection.
To select a radio station in the automatic mode,
advance the unit to the next available station, or the Down
Tuning ( 
) button to tune downward to the next available station. The radio will automatically seek the next strongest station. If the Local mode (LOCAL) is active, the radio will seek the next strongest local station when either button is pressed.
bn MANUAL SEEK TUNING
This function is used to search rapidly upward or downward for a desired station. By pressing either tune button for more than 2 seconds, the radio will enter the MANUAL seek mode as displayed momentarily on the panel. When either button is pressed and held in this mode, the radio will tune rapidly up or down and will stop at the station of choice when the button is released. A momentary press of either button in this mode will cause the radio to tune upward or downward one digit at a time. If tuning is not activated within 5 seconds of entering the MANUAL mode, the radio will automatically revert to the default AUTO mode as indicated momentarily on the panel.
bo LOCAL/DISTANT SELECTOR (LOC)
This feature is used to select the strength of the signals at which the radio will stop during Automatic Up/Down Tuning. Pressing the button will select the Local setting (LOCAL will appear on the display panel for 5 seconds) and tuning will select only strong (local) stations for reception. Pressing the button again will select the Distant setting (DX will appear on the display panel for 5 seconds) and the tuning will stop at a wider range of signals, including weaker (more distant) stations.
bp FM MONO SELECTOR (MONO)
During FM radio operation, this button is used to select mono or stereo reception of the broadcast signal. Under normal reception conditions, the unit should be left in the stereo mode as indicated by ST and the associated signal strength indicator on the display panel when tuned to an FM stereo signal. If the stereo signal is too noisy for comfortable listening, press the MONO button to switch to mono reception (the ST indication will disappear from the display panel, and MONO will momentarily appear). To return to stereo reception mode, press the button again; STEREO will momentarily appear on the display panel and the ST indication returns.
bq
Press this button momentarily to scan the stations pre- set into the memories on the 3 FM bands or the AM band. The unit will stop at each
Pressing and holding the button for longer than 2 seconds will activate the
IONSTINSTRUC INGTAOPER
7
OPERATING INSTRUCTIONS
8
br STATION
To set any of the 6
1. Turn the radio on and select the desired band. 2. Select the first station to be
Automatic Up/Down bm, or Manual Seek bn Tuning Controls.
3. Press and hold the
4. Repeat the above procedure for the remaining 5
bs EQUALIZER (EQ) BUTTON
The EQ button applies preset sound effects to the unit???s audio output signal.The EQ button, when pressed, will activate one of the following operating modes ( CLASSICS,
POP M, ROCK M, DSP OFF or FLAT). If the Equalizer function is active, as momentarily displayed on the panel, and the bass and/or treble level is set, the Equalizer function reverts to the the FLAT setting. On the other hand, if the Equalizer function is activated, the bass/treble setting(s) are ignored. Conversely, when the Equalizer function is not active, the unit returns to the user set bass
and treble levels.
bt
When this button is pressed during radio operation, each station in the current band will be scanned in the upward direction; each displayed station will flash for 5 seconds before moving on to the next station. If the local mode is active, only the stronger, nearby stations in the current band will be scanned. When the desired station appears, press the SCN button again to remain on that frequency.
bu LIQUID CRYSTAL DISPLAY PANEL
The Liquid Crystal Display (LCD) panel displays the frequency, time and activated functions, including a combination audio level/disc indicator in the form of dual
disc icons ( 
) with circular bar graphs depicting the
strength of the audio signal. In addition, the display also contains a receive signal indicator which depicts the relative strength of the incoming broadcast frequency.
NOTE: It is a characteristic of LCD panels that, if subjected to cold temperatures for an extended period of time, they may take longer to illuminate than under normal conditions. In addition, the visibility of the numbers on the LCD may slightly decrease. The LCD
cl CASSETTE DOOR
Hold the cassette with the exposed tape edge to the right and insert it fully into the cassette door until the cassette is engaged and begins playing (TAPE will appear on the display panel, together with three tape direction arrows). When the cassette reaches the end on the side of the tape being played, the unit will automatically change direction of play as shown by reversal of the three tape direction arrow indications on the display panel.
NOTE: Observe cassette operation cautions in Care and Maintenance section of this manual.
cm&
(
/ 
) These buttons cause the tape to move rapidly in the direction indicated by the arrows. For example, if the
button is pushed when the tape is moving from left to right ( >>> on the display panel), the tape will fast- forward. If the 
button is pressed while the tape is moving from right to left ( <<< on the display panel), the tape will rewind. To stop fast tape movement, lightly push the opposite button. If the tape is allowed to
co PROGRAM SELECTOR
To manually reverse tape direction and play the other side (program) of the cassette, lightly push both the Fast- Forward and Rewind buttons (
and 
) at the same time. The change of direction will be shown by the arrows on the display panel.
cp EJECT BUTTON ( 
)
Tape playback is stopped and the cassette is ejected by pressing this button. Radio operation will automatically resume when the cassette is ejected.
NOTE: Never leave a cassette engaged in the player when not in use. Doing so can cause damage to the cassette and/or mechanism of the unit. Always press the eject button and remove
the cassette before removing the detachable front panel.
cq MODE SELECTOR (MODE)
During radio or tape play, press this button to select operation of the optional CD changer as shown by CDC, the disc number and the track number on the display panel. Refer to the CD Changer Controls section for specific operating instructions.
If the button is pressed when no CD changer is connected to the unit, no CDC indications will appear on the display panel. The unit will then return to radio operation. To return to the tape operation (if a tape is loaded in the unit), press the button again. During tape play, press this button to change to radio operation without ejecting the tape.
cr TIME/FREQUENCY SELECTOR (T/F)
Pressing the Time/Frequency (T/F) button will display the time of day for 5 seconds, after which the display will automatically return to the radio, tape or CD changer display, depending on which one was currently active. To set the correct time of day, refer to the procedure for Setting the Clock.
Located on the chassis behind the front panel, a light- emitting diode (LED) will flash when the panel is removed. The flashing light serves as a visual warning to the
ct RESET BUTTON
A RESET button is located on the front of the chassis (front panel must be removed to access the button). The
1.Upon initial installation after all wiring is completed.
2.If there is a malfunction of any of the switches on the unit, pressing the RESET button may clear the system and return to normal operation.
cu FRONT PANEL RELEASE BUTTON
This button is used to release the mechanism that holds the front panel to the chassis. To detach the front panel, press the button so that the left side of the panel is released. Grasp the released side and pull it off of the chassis. To
dl DIMMER BUTTON (DIM)
This button provides control of the panel display brightness; when pressed once, the display will dim to half its normal intensity. When pressed again, the display will return to full brightness intensity.
NOTES ON USE OF FRONT PANEL
1.Make sure the front panel is
2.Do not press very hard on the front panel when attaching it to the chassis. No more than light to moderate pressure should be needed.
3.When attaching the front panel, make sure the right side is correctly engaged before pressing the left side to lock it into position.
4.When taking the front panel with you, please use the supplied carrying case to protect the panel from dirt and damage. Make sure there is no dust or dirt on the electrical terminals on the back of the panel as this could cause intermittent operation or other malfunctions.
CLOCK THE INGSETT / IONSINSTRUCT INGOPERAT
SETTING THE CLOCK
1.Switch the vehicle ignition and radio on.
2.Momentarily press the Time/Frequency (T/F) Select button cr so that the time is shown on the display panel.
3.Press and hold the Time/Frequency button until the time display begins flashing. While the display is still flashing,
press the Up Tuning ( 
) button to adjust the hours and then the Down Tuning ( 
) button to adjust the minutes to the correct time.
4.Five seconds after the last hour or minute adjustment is made, the time will be set in the unit and the display will return to the normal indication.
9
CARE AND MAINTENANCE
10
CARE AND MAINTENANCE
The radio section of your new sound system does not require any maintenance. We recommend that you keep this manual for reference on the many features found in this unit as well as how to set the clock.
The optional compact disc changer section also requires no routine maintenance, but proper under- standing of its use and handling will help you obtain maximum enjoyment of its capabilities.
CASSETTECARE
As with any cassette player, the cassette section of this sound system does require a minimum of maintenance to keep it in good working condition. The following simple care and maintenance suggestions should be followed to prevent malfunctions of the cassette system.
1.Purchase a cassette cleaning kit from your local retail store. Use it! At least every 20 to 30 hours of operation you must clean the cassette mecha- nism. A dirty cassette player will have a poor sound.
2.Do not use cassettes that exceed 45 minutes of play on each side.
3.Do not insert a cassette that appears to be broken, twisted or dirty or with loose or torn labels on it.
4.Always keep your cassettes away from direct sun light or exposure to subfreezing conditions. If a cassette is cold, allow it to warm up before use.
5.Do not keep a cassette in the player when not in use.
6.Before inserting a cassette in the player, check that the tape is tightly wound on the reels. Take up any excess slack using a pencil to turn the drive hub in the cassette.
HANDLING COMPACT DISCS (OPTIONAL CD CHANGER)
Dirt, dust, scratches, and warpage can cause skips in the playback and deterioration of sound quality. Please follow these guidelines to take care of your compact discs:
!Fingerprints, dust, and dirt should be carefully wiped off the disc???s playing surface (shiny side) with a soft cloth. Wipe in a straight motion from the inside to the outside of the disc.
!Never use chemicals such as record sprays, household cleaners or thinner to clean compact discs. Such chemicals can irreparably damage the disc???s surface.
!Discs should be kept in their storage cases when not in use.
!Do not expose discs to direct sunlight, high temperatures or high humidity for extended periods.
!Do not stick paper, tape, or labels on the disc surfaces nor write on them with any type of marker.
SPECIFICATIONS
*Specifications are subject to change without notice.
DISCS ON TESNO / IONSSPECIFICAT
11
THIS PAGE LEFT BLANK INTENTIONALLY
12
CD CHANGER CONTROLS
Built into this radio are controls to operate an optional CD changer. Please check with your Rampage/Audiovox car stereo specialist for recommendations of the models that will work with this radio.
Once the changer is installed and properly connected, it may be necessary to press the RESET button behind the radio front panel to initialize the complete installation.
Adjustment of the audio functions (volume, tone, balance, and fader) for the CD changer operate in the same manner as they do for radio play. The following controls will operate the CD changer when it is installed and connected to this radio. Refer to the owner???s manual included with the CD changer for instructions on the installation and correct loading and use of the CD magazine.
dm CD CHANGER PAUSE/PLAY SELECTOR ( PAU )
During radio, or tape play, press the MODE button to select operation of the CD changer as shown by CDC on the display. Disc play will begin, the disc and track number will be shown on the display panel, and the
center of the disc icon ( 
) will become animated. If
a new magazine has been loaded into the changer, play will begin from the first track of the first disc in the magazine. If a magazine was already in the changer, play will resume from the track on the disc previously in play. During CD changer play, pressing the PAU button once will stop changer play; PAUSE will appear on the display and the center of the disc icon will remain stationary. To resume disc play, press the PAU button again and disc play will resume from the point at which it was interrupted.
dn & do DISC SELECT (DN & UP)
These buttons are used to select the desired disc for play. To advance to a higher number disc, press the UP button do. To return to a lower number disc, press the DN button dn. The number of the disc in play will be shown on the display panel.
dp TRACK SELECT ( 
/ 
)
This button is used to quickly select the beginning of a particular track. With each momentary press of the Forward Track Select button ( 
), the next higher track number will be selected as shown on the display panel. Similarly, with each momentary press of the Backward Track Select button (
), the next lower track number will be selected.
dqFOWARD/REVERSE SEARCH (CUE/REVIEW)
) to advance rapidly in the forward direction, or press and hold the reverse (review) button ( 
) to advance rapidly in the reverse (backward) direction. In either case, the center of the disc icon will rotate faster when search is active.
dr TRACK SCAN SELECTOR (SCN)
When the SCN button is momentarily pressed, the SCN indication will appear on the display panel, and the first 10 seconds of each track on the disc will be played in order. When a desired track is reached, press the SCN button again and play of the selected track will continue (SCN will disappear from the display panel). The Track Scan mode will also be canceled by activating any other disc function (Track Select, Repeat or Random).
When the SCN button is pressed and held for more than 2 seconds, the disc scan mode is activated; DSN will appear on the display and the first 10 seconds of the first track on each disc will be played in disc order. This mode is canceled in the same manner as before.
ds TRACK REPEAT PLAY SELECTOR (RPT)
When the RPT button is momentarily pressed, the RPT indication will appear on the display panel and play of the current track will be continually repeated until the Track Repeat mode is canceled by pressing the RPT button again or by activating the Track Select, Random Play or Scan functions.
When the RPT button is pressed and held for more than 2 seconds, the disc repeat mode is activated; DRT will appear on the display and the play of the current disc will be continuously repeated. This mode is canceled in the same manner as before.
dtSHUFFLE PLAY SELECTOR (SHF)
When the SHF button is momentarily pressed, the SHF indication will appear on the display panel and the tracks on the disc will be played in a random, shuffled order. The Track Select buttons dp will also select tracks in the shuffled order instead of the normal progression. The Track Shuffle mode can be canceled by pressing the SHF button again or by activating the Track Select, Repeat Play or Scan functions.
When the SHF button is pressed and held for more than 2 seconds, the disc shuffle mode is activated; DSF will appear on the display and the play of the discs in the magazine will be played in a random shuffled order. This mode is canceled in the same manner as before.
SOLCONTR NGERACH CD
10
CD CHANGER ERROR CODES
14
CD CHANGER ERROR CODES
If a problem should develop while operating the CD changer, the error code ???Err??? may appear on the display panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control of the changer. If the error code should appear, try ejecting and
If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.
12 MONTH LIMITED WARRANTY
AUDIOVOXCORPORATION(theCompany)warrantstotheoriginalretailpurchaserofthisproductthat should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below.
This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE
EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO
CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 !
CANADA: CALL
YNTARRAW
15
