Television

User's Guide

Changing Entertainment. Again.

Weather and other hazard information brought to you by the National Oceanic and Atmospheric Administration (NOAA)

Important Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts.

Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

This symbol indicates important instructions accompanying the product.

This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury.

WARNING

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Product Registration

Refer to the identification/rating label located on the back panel of your product for its proper operating voltage.

FCC Regulations state that unauthorized changes or modifications to this equipment may void the user???s authority to operate it.

Caution: Using video games or any external accessory with fixed images for extended periods of time can cause them to be permanently imprinted on the picture tube (or projection TV picture tubes). ALSO, some network/program logos, phone numbers, etc. may cause similar damage. This damage is not covered by your warranty.

Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Please fill out the product registration card (packed separately) and return it immediately. For U.S. customers: Your RCA Consumer Electronics product may also be registered at www.rca.com/ productregistration. Registering this product allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers. These numbers are located on the product.

Model No. ____________________ Serial No. __________________ Purchase Date: ______________

Dealer/Address/Phone: _________________________________________________________________

Important Information

Alert Guard??? Important Information

???The green READY light on the front panel of the TV is the main indicator that the Alert Guard system is receiving NWR broadcast information. If it's not lit, the Alert Guard system can???t inform you of alerts. During poor reception conditions, the Alert Guard system might not inform you of alerts even if the green light is on.

???Generally, the Alert Guard system can fail to notify you of dangerous conditions for the following reasons:

1.National Oceanic and Atmospheric Administration (NOAA) did not broadcast an alert. Certain criteria must be met for NOAA to issue an alert, and only certain events are reported by NOAA. While weather forecasting continues to improve, it is not perfectly accurate. For this reason, situations that might be dangerous to you may be unknown to NOAA.

2.Power was lost to the TV during the time when an alert was broadcast. If power is lost for more than 15 seconds, the Alert Guard system will notify you that power was interrupted the next time the TV is turned on. Any alerts issued during a power failure won't be acknowledged by the Alert Guard system. Therefore, you might want to purchase a battery operated alert radio or have a battery powered radio available for listening when household power fails.

3.Reception of the NOAA Weather Radio (NWR) was poor at the time an alert was broadcast. Since NOAA only broadcasts an alert once, momentary loss of reception can prevent alerts from being received.

4.Options in the Alert Guard menu, such as locations and the NWR channel, were not set appropriately. Instructions within the User's Guide will help you set up Alert Guard correctly.

???Alert Guard shouldn't be your only source of information. You should always maintain personal, family, and neighborhood safeguard systems, and remain aware of changing conditions. The Alert Guard system relays alerts based on information provided by the NWR. The Alert Guard system is designed to recognize all alerts currently issued over the all hazards NWR broadcast system. Incidents (such as local traffic accidents and weather related school closings) that don't endanger the community with immediate threats are not broadcast.

???Alert Guard coverage is limited to the U.S., U.S. territories, possessions and associated states, within your local geographic area. These areas are listed on pages 37-54.

???While it appears you can set up the Alert Guard system to receive alerts from across the country, it can only receive alerts broadcast for areas close to the location of the TV.

???For models 20F670T, 27V570T and 27F670T, don???t leave headphones plugged in when they aren???t in use. Alarms will sound through the headphones and not the TV???s speakers, causing alarms not to be heard.

???If your TV is connected to a receiver, amplifier, home theater system, or other audio equipment, alerts won???t be audible through such devices connected to the audio output terminals of the TV; instead, the Alert Guard system will turn on the TV???s internal speakers to sound an alarm and make the alerts audible.

???Non-weather emergency messages, such as chemical spills, nuclear power plant emergencies, gas line breaks, etc., are not fully implemented nationally.

???If you receive an alert that tells you to seek shelter, do so immediately and don't continue to listen for other alerts until you are safe.

???It might take time, and after you've received several alerts, before you understand how the Alert Guard feature works.

???While government agencies use sophisticated equipment, such as weather models, radars, and satellites to determine an alert???s effective time and duration, the end of an alert also does not necessarily mean that related emergency events are over. Weather conditions can change rapidly, and caution should be taken before and after alerts.

Alert Guard is a trademark of Thomson Inc.

1

Table of Contents

2

Chapter 1: Connections & Setup

Things to Consider Before You Connect

Protect Against Power Surges

???Connect all components before you plug any of their power cords into the wall outlet.

???Turn off the TV and/or component before you connect or disconnect any cables.

???Make sure all antennas and cables are properly grounded. Refer to the Important Safety Instructions packed separately.

Protect Components from Overheating

???Don???t block ventilation holes on any of the components. Arrange the components so that air can circulate freely.

???Don???t stack components.

???If you place components in a stand, make sure you allow adequate ventilation.

???If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it won???t flow around other components.

Position Cables Properly to Avoid Audio Interference

???Insert each cable firmly into the designated jack.

???If you place components above the TV, route all cables down the side of the back of the TV instead of straight down the middle of the TV.

???If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin lead cables away from audio/video cables.

Important Stand and Base Safety Information

Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This could cause personal injury and/or damage the TV. Refer to the Important Safety Instructions packed separately.

Use Indirect Light

Don???t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or indirect lighting.

Cables Needed to Connect Components to Your TV

The pictures below show the cables needed for the connection represented in this book.

Alert Guard Antenna

The picture to the left shows the Alert Guard antenna packed with your TV, specifically designed for the Alert Guard feature. Connect the antenna to the EXT Alert Guard ANT jack on the back of the TV (go to page 8 for more information). Don???t connect the antenna to the regular TV ANT jack on the back of the TV.

Alert Guard Antenna

Connections & Setup

From Cable or Antenna

1D

1B 1A

DVD

1C*

OUT

S-VIDEO

TV + DVD + VCR

* If you connect an S-Video cable, you must connect the audio cables to the VIDEO 1 AUDIO jacks on the back of the TV, not the VIDEO 2 AUDIO jacks.

1.Connect your DVD Player to your TV.

A.Connect the audio (white and red) cables to the VIDEO 2 R and L/MONO AUDIO jacks on the back of the TV and to the Audio Output jacks on the DVD player.

B.If your DVD player has Component Output Jacks (Y, Pb, Pr), connect three video grade cables to the Y, Pb, Pr jacks on the DVD player and to the VIDEO 2 Y, Pb, Pr jacks on the back of the TV. If your DVD player doesn???t have Y, Pb, Pr jacks, go to C.

-OR-

C.If your DVD player has an S-Video Jack, connect an S-Video cable to the S-Video jack on the DVD player and to the S-VIDEO IN jack on the back of the TV. If your DVD player doesn???t have an S-Video jack, go to D.

Note: If you connect an S-Video cable, you must connect the audio cables to the VIDEO 1 AUDIO jacks on the back of the TV, not the VIDEO 2 AUDIO jacks.

-OR-

D.Connect a video cable (yellow) to the Video Output Jack on the DVD player and to the VIDEO 2 VIDEO jack on the back of the TV.

2.Connect your TV to your VCR.

Connect a coaxial cable to the TV ANT jack on your TV and to the Antenna Output Jack on your VCR (sometimes labeled OUT TO TV).

Note: If your VCR has Audio/Video output jacks, you can connect your TV to your VCR using audio/video cables for better quality.

3.Make sure cable or antenna is connected to your VCR.

Connect the coaxial cable from your cable outlet or antenna to the Antenna Input Jack (sometimes labeled IN FROM ANT) on the VCR.

Go to page 8

Connections & Setup

Explanation of Jacks

This section describes the jacks you can use to make connections. There are several ways to connect components to your TV.

TV ANT Lets you connect a coaxial cable to receive the signal from the antenna, cable, cable box, or if using the example on page 4, a VCR.

EXT Alert Guard ANT Lets you connect an antenna if you need to receive a stronger signal for the Alert Guard feature. Go to page 8 for more information.

R AUDIO L/MONO VIDEO

Pr Pb Y

Y

L

Pb AUDIO

R

Pr

1 VIDEO

2 VIDEO

3 VIDEO

VIDEO 1

VIDEO, AUDIO R and L/MONO INPUTS Lets you connect a component such as a VCR, DVD player, or laserdisc player.

???R (RIGHT) AUDIO Provides right audio connection. The right audio connector is usually red.

???L/MONO AUDIO Provides left audio connection. The left audio connector is usually white.

???VIDEO Provides composite video connection. The video connector is usually yellow.

???S-VIDEO Provides better picture quality than the composite video jacks because the color part of the signal is separated from the black and white part of the picture. When using S-VIDEO IN, make sure to also connect left and right audio cables to the VIDEO1 AUDIO Input jacks.

VIDEO 2

VIDEO, AUDIO R and L/MONO and Y, Pb, Pr INPUTS Lets you connect a component video source, such as a DVD player.

???Y, Pb, Pr Provides optimum picture quality because the video is separated into three signals. Use three video- grade cables for the connection. When using VIDEO 2

Y, Pb, Pr, make sure to also connect left and right audio cables to the VIDEO 2 AUDIO Input jacks.

second component video source, such as a DVD player. Their description is the same as VIDEO 2 above. When using VIDEO 3 Y, Pb, Pr, make sure to also connect the left and right audio cables to the VIDEO 3 AUDIO Input jacks.

Connections & Setup

R L V

OUTPUT

AUDIO/VIDEO OUTPUTS (Video Out not available on model 27V570T) Lets you connect an amplifier or audio receiver for improved sound quality or an external video monitor, for models with Video Out.

27V570T Front Panel

20F670T, 27F670T, 32F670T Front Panel

The Front of Your TV

Alert Guard Front Panel Buttons and Lights

READY (Green Light) Remains lit as long as the TV is receiving a strong signal.

ADVISORY (Yellow light) On during Advisory alert. Also, lights for approximately 15 minutes during the weekly NOAA (National Oceanic and Atmospheric Administration) Weather Radio (NWR) test.

Note: The lights blink when an alert is first received. To stop them from blinking, press STOP ALARM. Lights stay on until an alert has expired. For your protection, you can never turn a light off while an alert is in effect.

VIEW MESSAGE Press the VIEW MESSAGE button to display the alert being issued. If the TV is off, pressing this button turns on the TV and displays the message. Press this button at any time during an alert or weekly test to display the time remaining until the alert or test expires.

HEAR VOICE Toggles the NWR on and off.

STOP ALARM Turns off alarms and then removes on-screen messages.

Connections & Setup

AUDIO

H-PHONE VIDEO L/MONO RIGHT S-VIDEO

Front Input Jacks

The TV has front input jacks for your convenience: one set of audio/video inputs, an S-Video and a headphone jack. These jacks are towards the front of the TV on the side. To access the component you connected to the front of the TV, press the INPUT button on your remote until FRNT (SFRNT for S-VIDEO) appears on the screen. The jacks are ideal for connecting a video game console or a camcorder.

Note: When connecting a component that only has one audio jack, such as some camcorders, use the TV???s AUDIO L/MONO jack to hear the audio.

H-PHONE (Headphones- not available on model 32F670T) Allows you to connect headphones to listen to the sound coming from the TV.

Note: For models 20F670T, 27V570T and 27F670T, don???t leave headphones plugged in when they aren???t in use. Alarms will sound through the headphones and not the TV???s speakers, causing alarms not to be heard.

VIDEO Receives video from another component such as a VCR, camcorder, or video game console.

L/MONO and RIGHT AUDIO Receives audio from another component such as a VCR, camcorder, or video game console.

S-VIDEO Allows you to connect an S-Video cable from another component. Make sure you also connect audio cables from the component to the TV.

Front Panel Buttons

If you can???t locate your remote, you can use the front panel buttons of your TV to operate many of the TV???s features.

MENU/OK Brings up the Main menu. In the menu system, it selects highlighted items.

CH v Scans down through the current channel list. In the menu system, acts like the down arrow button on the remote control and adjusts menu controls.

system, acts like the up arrow button on the remote control and adjusts menu controls.

VOL < Decreases the volume. In the menu system, acts like the left arrow button on the remote control and adjusts menu controls.

VOL > Increases the volume. In the menu system, acts like the right arrow button on the remote control and adjusts menu controls.

POWER Turns the TV on and off.

Connections & Setup

TV (back panel)

From Cable, Antenna, or Satellite Receiver

Connect Alert Guard Antenna

Connect the supplied antenna, with the rod positioned straight up and down, to the EXT Alert Guard ANT jack on the back of the TV.

Connect TV Antenna

If you haven???t already, connect the coaxial cable from your cable source (if using the example on page 4, a VCR) to the TV ANT jack on the back of the TV.

Plug in the TV

Plug the end of the power cord into a grounded wall outlet. Insert the plug completely into the outlet.

Put batteries in the remote

???Remove the battery compartment cover from the back of the remote by pushing down on and sliding off the cover.

???Insert 2 fresh ???AA??? batteries. Make sure the polarities (+ and -) are aligned correctly.

???Replace the cover.

DVD VCR2 AUX SAT???CABLE

Arrows

OK button

How to Use the Remote Control to Complete the Initial Setup

The technical term is ???Navigation?????? how you move through the on-screen menus. The method is the same throughout the menu screens: highlight your choice and select it.

To highlight a menu item, press the arrow buttons on the remote to highlight one of the items listed on the screen. Use the up or down arrow button to move up or down. Use the right or left arrow button to move right or left.

To select the item that you???ve highlighted, press OK.

Note: Highlighted means that the menu item stands out from other menu items on the list (appears darker, brighter, or a different color).

. . .
. . .

Connections & Setup

Turn on the TV

Press TV on the remote, or press POWER on the TV???s front panel.

Note: Pressing the TV button not only turns on the TV, but puts the remote into TV mode. ???TV mode??? means that the buttons on the remote control operate the TV???s functions.

AUTO CHANNEL SEARCH

Start

Channel

Complete the Initial Setup

The menu system in your TV allows the TV???s features to work properly. The first time you turn on your TV, the SETUP screen appears with Language highlighted. The default language is English. To choose another language, press the right arrow button.

Complete Auto Channel Search

This part of the setup allows the TV to search for all channels viewable through your antenna or cable TV system. This is sometimes called auto programming.

1.Highlight Auto Ch. Search and press OK.

2.The Signal Type option is set to Cable. To change the option to Antenna, press the right arrow button.

3.Press the down arrow button to highlight Start. Press the OK button to begin the auto channel search.

Once the search is complete, the Alert Guard Setup menu appears.

Alert Guard Initial Setup

Alert Guard informs you of hazards such as winter storm watches and civil danger warnings that are being broadcast by the all hazards NWR broadcast system for your specific area.

Note: Alert Guard receives alerts for the U.S. , U.S. territories, possessions and associated states, within your local geographic area. Your TV can???t respond to alerts outside these areas. These areas are listed on pages 37-54.

Also, Alert Guard can only receive alerts broadcast for areas close to the location of the TV.

ALERT GUARD SETUP

Select where your TV is from a list or by phone .

Pick from list

Call a number

1.The quickest way to set your area is to highlight Pick from list and press OK. (If you want to set up Alert Guard by phone, highlight Call a number, call 1-888-NWR- SAME, and follow the on-screen instructions).

S e l e c t y o u r l o c a t i o n f r o m a l i s t .

(steps continued on the next page)

Connections & Setup

PICK FROM LIST

Go back

All of U. S. . . .

Continue . . .

S e l e c t a s t a t e , t e r r i t o r y,

m a r i n e a r e a , o r D . C . w i t h t h e l e f t o r r i g h t k e y. C h o o s e t h e a r e a w h e r e y o u r T V i s n o w.

S e l e c t a s t a t e , t e r r i t o r y,

m a r i n e a r e a , o r D . C . w i t h t h e l e f t o r r i g h t k e y. C h o o s e t h e a r e a w h e r e y o u r T V i s n o w.

S e l e c t a c o u n t y, c i t y, e t c . , w i t h t h e l e f t o r r i g h t k e y.

I f a r e a n o t f o u n d , G o b a c k , a n d C a l l a n u m b e r.

2.The PICK FROM LIST menu appears with All of U.S. highlighted. Press the left or right arrow button to choose your region- the state, territory, or marine area where you are living or District of Columbia. These are listed in alphabetical order, with marine areas at the end of the list (press the left arrow button to access these quickly, starting at the end of the list).

3.After you set your region, press the down arrow button to highlight All nearby. Press the left or right arrow button to choose the county, city, parish, area, borough, district, island, atoll, state or municipality where you are living. These are also listed in alphabetical order. Most states only have counties as a choice.

The location code is now set. Highlight and select Continue. Alert Guard is ready to receive information specific to your area.

If you receive an on-screen message, YOU MIGHT MISS ALERTS!, press OK to tune to the strongest NWR channel. The NWR channel menu appears and searches for a strong channel.

Listen to the NWR channel. If the signal is clearly understandable and is broadcasting information for your local area, press CLEAR. Alert Guard is set up appears on- screen. Press CLEAR again to watch TV. If the signal isn???t understandable or isn???t broadcasting information for your local area, go to page 33 for more information.

You can set each alert level, Warning, Watch or Advisory, to notify you of alerts broadcasted by receiving a message on-screen or hearing a type of alarm. The default settings for these alert levels are:

To change these setting and for more information on how to customize options in Alert Guard, go to Chapter 3.

Note: If you move from the area you set in the Initial Setup, you need to set your new area in the Alert Guard LOCATIONS menu.

Chapter 2: Using the Remote Control

Indicator

REVERSE PLAY FORWARD

RECORD STOP PAUSE

ALERT GUARD

VIEW HEAR STOP NEWS

MESSAGE VOICE ALARM WEATHER

Button Descriptions for TV Mode

Arrows Used to point to different items in the TV menu and to adjust the menu controls.

Indicator Indicates the programming mode when programming the remote to control components. Lights when you press a valid button on the remote.

(0-9) Number Buttons Enter channel numbers and time settings directly through the remote control.

To enter a one-digit channel, enter a zero first. To enter a two-digit channel, press the two digits and expect a few seconds delay. This is in case you want to enter a third digit.

CH + or CH - Scans up or down through the current channel list. Press once to change the channel up or down; press and hold to continue changing channels.

CLEAR Removes any menu or display from the screen and returns you to normal viewing.

GO BACK Returns you to the previous channel.

INFO Brings up channel banner; press again to clear the screen.

INPUT Toggles through the available input sources (VID1/SVID1, VID2/CVID2, FRNT/SFRNT, CVID3 and current channel).

MENU Brings up the Main menu.

MUTE Reduces the TV???s volume to its minimum level. Press again to restore the volume.

OK When in the menu system, selects highlighted items.

ON???OFF When in TV mode, turns the TV on and off. If in another mode (VCR, DVD, SAT???CABLE, etc.), will turn the component on and off.

SKIP Press once before changing channels and the TV will go back to the original channel after 30 seconds. Press repeatedly to add more time.

SOUND Displays the SOUND menu.

TV Turns on the TV and puts the remote in TV mode. Also displays current status.

VOL ??? or VOL + Decreases or increases the TV???s volume.

Button Descriptions for Alert Guard

(Listed from left to right)

VIEW MESSAGE Press to display the alert being issued. If the TV is off, pressing this button turns on the TV and displays the message. Press this button at any time during an alert or weekly test to display the time remaining until the alert or test expires.

HEAR VOICE Toggles the NWR on and off.

STOP ALARM Turns off alarms and then removes on-screen messages.

NEWS WEATHER Scans through the four channels in the order they were set in the News Weather menu. If no channels have been set up, the default News Weather station is channel 6. If the TV is off, pressing this button turns the TV on and tunes to the first News Weather channel.

Using the Remote Control

Button Descriptions for Other Modes

AUX Puts the remote in AUX mode. Can also be programmed to operate most brands of an additional remote-controllable component.

ANTENNA In VCR mode, functions as a TV/VCR button. In SAT???CABLE mode, functions as a TV/receiver button.

DVD Puts the remote in DVD mode and, if auto tuning is enabled, will turn on the TV and tune to the correct video input channel.

GUIDE If you???re operating another component that has an on-screen program guide, this button accesses the on-screen guide.

REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE If programmed, provides transport control for some remote-controllable VCRs, DVD players, and CD players.

SAT???CABLE Puts the remote in SAT???CABLE mode and, if auto tuning is enabled, will turn on the TV and tune to the correct video input channel.

VCR1 Puts the remote in VCR mode and, if auto tuning is enabled, will turn on the TV and tune to the correct video input channel.

VCR2 Puts the remote in VCR mode to operate a second VCR and, if auto tuning is enabled, will turn on the TV and tune to the correct video input channel.

Using the INPUT Button

Use the INPUT button to scroll through the available video input channels and view components you have connected to the TV.

1.Press TV to place the remote in TV mode. Make sure the component you want to view is turned ON.

2.Press INPUT to tune to an available video input source and view the component.

3.To return to the previous channel, continue pressing INPUT.

Using the Remote Control

button

You???ll use these buttons when programming the remote.

Programming the Remote to Operate Other Components

The universal remote can be programmed to operate most brands of remote controllable components. The remote is already programmed to operate most RCA, GE, and Proscan components.

Also, the AUX button can be programmed to operate most brands of an additional remote-controllable component.

Notes: The TV button can???t be programmed on this remote.

The remote may not be compatible with all brands and models of components. It also may not operate all functions of the remote that came with your component.

Find Out If You Need to Program the Remote

To determine whether the universal remote needs to be programmed for your component, turn the component ON. For example, to program the remote for a VCR, turn on the VCR. Point the remote at the VCR, and press the VCR1 button. Then press ON???OFF or CH + (channel up) or CH ??? (channel down) to see if the VCR responds to the remote commands. If the component does not respond, the remote needs to be programmed.

Programming the Remote

There are two ways to program the remote control:

???automatic code search

???direct entry

Using Automatic Code Search

The following instructions can be used to program the remote to operate each of your components. If you want to stop the automatic code search without programming any of your components, press CLEAR until the indicator on the remote turns off.

1.Turn on the component you want to operate (VCR, DVD player, etc.)

2.Press and hold the component button you want to program (VCR1, DVD, etc.). While holding the component button, press and hold ON???OFF until the indicator on the remote turns on, then release both buttons.

3.Point the remote at the component. Press and release PLAY, then wait 5 seconds or until the indicator on the remote stops flashing.

At this point the remote is searching for the correct code to program. If, after 5 seconds, the component you want to operate does not turn off, press PLAY again to tell the remote to search the next set of codes.

Continue pressing PLAY until the component turns off or you have searched through all of the codes. There are 20 total sets of codes. If the component does not turn off after pressing PLAY 20 times, then the remote can???t be programmed to operate that component. Press CLEAR to turn off the indicator light.

Using the Remote Control

If the component you want to control does turn off:

1.Press and release REVERSE, then wait 2 seconds. Repeat this step until the component turns back ON.

2.To finish, press and hold STOP until the indicator on the remote turns off.

Using Direct Entry

1.Turn on the component to be programmed.

2.Look up the brand and code number(s) for the component on the code list in this section.

3.Press and hold the component button you want to program on the remote.

4.Enter the 4-digit code from the remote control code list on the following pages. If the indicator flashes, you have either entered an invalid code or the button isn???t programmable.

5.Release the component button.

6.Point the remote at the component. Press ON???OFF to see if the component responds to the command. If it doesn???t, try pressing the component button and then ON???OFF again.

???If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote commands.

???If you try all the codes for your component brand and none work, try the automatic code search method. If automatic code search doesn???t find the code, the remote is not compatible with your component.

How to Use the Remote After You???ve Programmed It

Because this universal remote can control several different components (TV, DVD, VCR, satellite receiver, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote to control the TV, you would press the TV button to put the remote into TV mode before you could control the TV.

1.Press the appropriate component button (DVD, TV, VCR1, VCR2, SAT???CABLE, AUX) to set the remote to control the component.

2.Press ON???OFF to turn the component ON or OFF.

3.Use the remote buttons that apply to that component.

Note: If you keep pressing buttons and nothing happens, the remote is probably in the wrong mode. You must press the component button that matches the component you want to operate (i.e., if you want to operate the VCR, press VCR1 on the remote control to put the remote in VCR mode.)

Using the Remote Control

Remote Control Codes

VCR Codes

Programmable for VCR1, VCR2 and AUX buttons.

Using the Remote Control

Programmable for SAT???CABLE and AUX buttons.

Satellite Receiver Codes

Programmable for SAT???CABLE and AUX buttons.

Using the Remote Control

Satellite Receiver Codes continued

Chapter 3: Using the TV???s Features

Alert Guard

Alert Guard receives digital data known as SAME (Specific Area Message Encoding) combined with audio information provided by NOAA (National Oceanic and Atmospheric Administration) Weather Radio (NWR).

Note: For more information about NOAA, visit www.noaa.gov.

NOAA conducts a weekly test for the all hazards broadcast system. The test is once a week on Wednesday between 10 a.m. and 12 noon for approximately 15 minutes. The yellow ADVISORY light blinks during the test. If there is ongoing severe weather or a threat of severe weather, the test is postponed until the next available good-weather day. Alert Guard uses this test to ensure you???ve set the channel and locations properly. If Alert Guard detects a problem, on-screen messages appear to provide help.

The Alert Guard system receives alerts for the U.S., U.S. territories, possessions and associated states, within your local geographic area. Your TV can???t receive any alerts for locations outside these areas. Also, if alerts are issued for areas other than those that you set in the Location menu, Alert Guard won???t notify you of those alerts.

Alerts received by the Alert Guard system follow:

NOAA Natural and Weather Events- These include approximately 30 alerts, such as tornadoes, flash floods, avalanches, blizzards, forest fires, hurricanes, tsunamis, volcanoes, earthquakes, etc.

State and County Civil Emergency Alerts- The Alert Guard feature responds to current civil emergency alerts issued by all hazards NWR network. These include localized nuclear power plant emergencies, gas line breaks, train derailments, missing children alerts (America???s Missing: Broadcast Emergency Response- AMBER Alerts), etc. These non-weather emergency messages are not fully implemented nationally.

National, Regional and State Civil Emergency Alerts- These include high level state or federal emergencies, such as national attack warnings, terrorist attack alerts (not alert level or threat condition status), bio-warfare alerts and other immediate life-threatening emergencies. This information is relayed by the Federal Emergency Management Agency (FEMA) and NOAA over the all hazards NWR network.

Alert Guard has several different levels of alerts. A list and explanation follows:

Warning- These alone pose a significant threat to public safety and/or property, probability of occurrence and location is high, and the onset time is relatively short.

Watch- Meets classification of a warning, but either the onset time, probability of occurrence, or location is uncertain.

Advisory- This event by itself might not kill, injure, or cause property damage but may indirectly cause other things to happen that result in a hazard.

A list of the type of alert levels you can receive follows on the next page.

Chapter 3: Using the TV???s Features

Alerts

Note: Alert messages provide only basic information. For example, if a Civil Emergency Message appears on-screen, you need to press HEAR VOICE to hear information about the specific alert it???s covering, such as a train derailment, toxic gas leak, oil refinery fire, water supply pollution or an industrial explosion.

S e t o p t i o n s f o r W a r n i n g s , W a t c h e s , a n d A d v i s o r i e s b y p r e s s i n g t h e l e f t / r i g h t k e y s .

Alert Options

You can customize how you want to receive each alert level.

1.Press the MENU button (the MAIN MENU appears).

2.Press the down arrow button to highlight Alert Guard and press OK.

3.Select Alert options from the ALERT GUARD menu.

4.Press the right arrow button to highlight the alert level you want to customize, for example, Advisory.

5.Press the down arrow button to highlight Message seen. If you want an alert message to appear on-screen when receiving an Advisory, press the right arrow button until the Message seen box is checked.

Notes: Alert messages don???t appear when the TV is off.

Alert messages provide only basic information. You might need to press HEAR VOICE to get more specific information.

(steps continued on the next page)

Using the TV???s Features

6.Press the down arrow button to highlight Alarm type. Press the right arrow button to highlight the type of alarm you want to hear when receiving an Advisory. If you don???t want any alarm set, choose None.

Notes: For models 20F670T, 27V570T and 27F670T, don???t leave headphones plugged in when they aren???t in use. Alarms will sound through the headphones and not the TV???s speakers, causing alarms not to be heard.

If your TV is connected to a receiver, amplifier, home theater system, or other audio equipment, alerts won???t be audible through such devices connected to the audio output terminals of the TV; instead, the Alert Guard system will turn on the TV???s internal speakers to sound an alarm and make the alerts audible.

7.If you set an Alarm type, press the down arrow button to highlight Alarm volume. Press the right or left arrow button to set the highest volume of the alarm. You might want to think of how loud the volume needs to be if you???re somewhere else in your home . For example, if you want the alarm to wake you up while sleeping in the other room, then you might need to set the volume at the highest level.

The Siren option is a loud sound, designed to get your attention. The Chime option is a subtle sound for those easily startled. When the Siren or Chime sounds, it starts soft and continues to get louder until it reaches the maximum volume you set. The Voice option is the voice of NWR which states the alert and then shuts off. The Voice option doesn???t get louder. It speaks at the volume you set.

8.When finished, if you want to customize Warning or Watch level, press the up or down arrow button to highlight Alert level. Then follow steps 4-7.

S e l e c t a s t a t e , t e r r i t o r y,

m a r i n e a r e a o r D . C . w i t h t h e l e f t o r r i g h t k e y .

S e l e c t a c o u n t y, c i t y, e t c . , w i t h t h e l e f t o r r i g h t k e y.

I f y o u r a r e a i s n o t f o u n d , s e t t h e c o d e m a n u a l l y.

Locations

You can receive alerts from three other locations within close proximity of where you live. To set these areas:

1.Press the MENU button (the MAIN MENU appears).

2.Press the down arrow button to highlight Alert Guard and press OK.

3.Select Locations from the ALERT GUARD menu.

4.Press the left or right arrow button to choose which area you want to set, for example Nearby 1 (if you completed the Alert Guard initial setup, My Area has already been set). Set the areas in order of priority.

5.Press the down arrow button to highlight No area.

6.Press the right arrow button to highlight the state, territory, or marine area where you are living or District of Columbia. These are listed in alphabetical order, with marine areas at the end of the list (press the left arrow button to access these quickly).

7.Press the down arrow button to highlight All nearby.

8.Press the right arrow button to choose another area different than the area set for My Area. This could be another county, city, parish, area, borough, district, island, atoll, state or municipality nearby where you are living.

The location code is now set. If you want to set another area, press the up arrow button to highlight Location. Press CLEAR to exit.

Using the TV???s Features

9.If you can???t find your location, you need to set it manually. Press the down arrow button to highlight Location code.

10.Go to pages 37-54 or call toll-free 1-800-NWR-SAME to find the location code for your area. Enter the code using the number buttons on the remote.

Note: Occasionally the government changes or adds location codes. If you live in a new county or renamed county, you need to call 1-800-NWR-SAME because the code probably isn???t in the list. Enter the code using the number buttons on the remote. Question marks (???) will appear in the area above the location code, which is normal since the TV isn???t aware of this new area. Alert Guard will still respond if an alert is received for this location.

E n t e r a T V c h a n n e l t o b e s e l e c t a b l e w i t h t h e N E W S W E AT H E R k e y.

News Weather

You can set up to four different news or weather channels which correspond to the NEWS WEATHER button on the remote.

The default for Choice 1 is channel 6. To set a different channel:

1.Press the down arrow button to highlight Choice 1.

2.Press the left or right arrow button to choose the first news weather channel. You can also use the number buttons to enter the channel, for example, channel 12. Press number 1, then 2, and then press OK.

3.To set the other news weather choices, follow the same steps.

Each time you press the NEWS WEATHER button, the TV toggles through the choices in the order they were set.

NWR Channel

Alert Guard can search for the strongest NWR channel to use in order to receive an alert. If your TV is having trouble receiving a channel, you might need to search again for the NWR channel.

1.Select NWR channel from the ALERT GUARD menu.

2.Press the down arrow button to highlight Start search.

3.Press the OK button to begin the channel search. The TV searches through channels 1-7 to find the strongest reception.

Notes: You might want to search manually for the best channel. The best channel is one that broadcasts information for your local area and is clearly understandable. Highlight NWR channel and press the left or right arrow button to select a channel.

The NWR channel and location work together. A transmitter serves specific counties, cities, etc., nearby. It might be necessary to select a different channel or locations. If Alert Guard detects a problem, on- screen messages appear to provide help.

Using the TV???s Features

Channel Banner

There are several items that might appear when you press the TV or INFO button on the remote. This display is called the Channel Banner. The following list describes the items on the Channel Banner screen (left to right and top to bottom).

Why You Should Use the Auto Tuning Feature

The auto tuning feature automatically tunes the TV to the correct channel for different components you have connected to your TV (like a VCR, DVD Player, etc.) When you set up auto tuning in the menu system, you don???t have to remember to change your TV to channel 3; for example, when you want to watch the tape in your VCR.

How to Set Up the Auto Tuning Feature

The way you set up the auto tuning feature in the TV???s menu corresponds to the component buttons on the remote and the way you have each component connected to your TV. When you set up auto tuning, you???re telling the TV what channel to tune to when you press the VCR1, VCR2, DVD, or SAT???CABLE button on the remote control.

1.Press MENU (the MAIN MENU appears).

2.Highlight Setup and press OK on your remote control.

3.Highlight Auto Tuning and press OK.

Using the TV???s Features

4.Choose which channel you would like to set:

Set VCR1 The channel the TV tunes to when you press the VCR1 button. Set VCR2 The channel the TV tunes to when you press the VCR2 button. Set SAT/CABLE The channel the TV tunes to when you press the SAT???CABLE button.

Set DVD The channel the TV tunes to when you press the DVD button.

5.Press the right arrow button to select the choice that matches the way you have the component connected to this TV, and press OK.

The choices and a brief explanation follow:

N/A Choose this if you don???t have this particular component connected to the TV, or if you don???t want the TV to automatically tune to the correct channel when you???re using this component.

CH02 (SAT/CABLE only) Component is connected to the TV ANT jack on the back of the TV, and you want the TV to tune to channel 2 when you press the SAT???CABLE button on the remote. Reminder: make sure the component???s Channel 2/3/4 switch is set to channel 2. Usually this switch is on the back of the component.

CH03 or 04 Component is connected to the TV ANT jack on the back of the TV, and you want the TV to tune to channel 3 or 4 when you press the corresponding button on the remote. Reminder: make sure the component???s Channel 3/4 switch is set to the appropriate channel.

VID1 Component is connected to the VIDEO 1 VIDEO or S-VIDEO jack on the back of the TV and you want the TV to tune to a video input channel when you press the corresponding button.

VID2 Component is connected to the VIDEO 2 VIDEO or

Y, Pb, Pr jacks on the back of the TV and you want the TV to tune to a video or component video input channel when you press the corresponding button.

VID3 Compatible component video source, such as a DVD player or digital TV converter box, is connected to the VIDEO 3 Y, Pb, Pr jacks on the back of the TV and you want the TV to tune to the component video input channel when you press the corresponding button.

FRNT (Front Video Input) Component is connected to the VIDEO or S-VIDEO jack on the front of the TV and you want the TV to tune to the front video input channel when you press the corresponding button.

Using the TV???s Features

Parental Controls and V-Chip

The choices in the USA V-CHIP menu involve software inside your TV (referred to as V-Chip) which allows you to block TV programs and movies based on violence, sex, or other content you may believe children should not view.

Once you block programs, you can unblock programs by entering a password.

By default, the software inside your TV is turned ???off.??? For instructions to turn on V-Chip, go to page 28.

How V-Chip Works

V-Chip reads the program???s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence (V), Adult Language (L), etc.)]. If you have blocked the rating and/or content themes that the program contains, you will receive the message

This channel has not been approved for viewing. Change channel or press OK to enter password and temporarily deactivate the Parental Control.

Broadcasters are not required to provide content themes, so programs received with no content themes will only be blocked if you block their age-based rating. You can also block out programs that have been given a rating of Not Rated, and programs that are considered unrated. The TV age-based ratings and content themes you can block follow:

USA V-Chip Rating System

TV-MA (Mature Audience Only) Specifically designed to be viewed by adults and may be unsuitable for children under 17. It contains one or more of the following content themes: crude indecent language (L), explicit sexual activity (S), or graphic violence (V).

TV-14 (Parents Strongly Cautioned) Contains some material that many parents would find unsuitable for children under 14. Parents are strongly urged to exercise greater care in monitoring this program and are cautioned against letting children under the age of 14 watch unattended. This program contains one or more of the following content themes: intensely suggestive dialogue (D), strong coarse language (L), intense sexual situations (S), or intense violence (V).

TV-PG (Parental Guidance Suggested) Contains material that parents may find unsuitable for younger children. Many parents may want to watch it with their younger children. The program contains one or more of the following content themes: some suggestive dialogue (D), infrequent coarse language (L), some sexual situations (S), or moderate violence (V).

TV-G (General Audience) Most parents would find this program suitable for all ages. It contains little or no sexual dialogue (D) or situations (S), no strong language (L), and little or no violence (V).

TV-Y7 (Directed to Children 7 years and older) Designed for children ages 7 and above. It may be more appropriate for children who have acquired the developmental skills needed to distinguish between make-believe and reality. Themes and elements in this program may include mild fantasy violence (FV) or comedic violence, or may frighten children under the age of 7.

TV-Y (All Children) Themes and elements in this program are designed for a young audience, including children from ages 2-6. It is not expected to frighten younger children.

Using the TV???s Features

Press OK to view/block prog. with this rating.

USA V-Chip TV Rating Limit

The V-Chip TV Rating Limit lets you decide which TV programs can and cannot be viewed.

To set TV programming limits:

1.Choose Parental Control from the MAIN MENU (the PASSWORD screen appears the first time you enter the Parental Control menu). Create your password using the number buttons on the remote.

2.Highlight and select USA V-Chip. Then select TV Ratings.

3.Once you get to the TV RATING LIMIT screen, use the arrow buttons and OK on your remote to change the status of a TV program rating or content theme from

View to Block.

4.For TV rating limits to take effect, turn on V-Chip active in the PARENTAL CONTROL menu (box has check mark).

The following sections give you more details about how to change the status of TV program limits.

Note: If you forget your password you can reset it. Make sure the TV is off. Simultaneously press and hold VOL< on the TV???s front panel and CLEAR on the remote for approximately 5 seconds. Enter a new password the next time you access the PARENTAL CONTROL menu.

The V-Chip Rating Screen

The following is an example of where items are located within the Rating Limit screen.

Rating Status Field

Lets you select whether the status of the age-based rating limit to the left is View or Block.

Rating Field

Lets you select from a list of age-based ratings you can block or view.

Content Themes

Lists the content themes you can block or view.

Content Status Fields

Lets you select which content themes to view for the selected rating, and whether the status of the content theme is currently View (V) or Block (B).

Rating Settings Area

Lets you see the current block/view state of age-based ratings and associated content.

Using the TV???s Features

Hierarchy of Age-Based Ratings

Press OK to view/block

prog. containing adult language.

Blocking Age-Based Ratings

You can automatically block all program ratings above a specified age-based rating level.

To block programs with higher ratings:

1.Press the up or down arrow button to scroll to the rating corresponding with the lowest rating you don???t want the child to watch.

2. Press the OK button to toggle between View and Block. The status for the rating listed to the left and all higher ratings automatically changes to Block.

3.Press the up or down arrow button to highlight Go back and press OK.

4.Turn on V-Chip active in the PARENTAL CONTROL menu (box has check mark) for rating limits to take effect.

Viewing Age-Based Ratings

After you block age-based ratings, you can change some of the ratings back to View.

1.Press the up or down arrow button to select the rating with a status of Block.

2.Press OK to select View.

Blocking Specific Content Themes

You can block programs based on their content. (Content is represented by the D, L, S, V and FV on your screen.) When you block a content theme for a particular rating, you automatically block that content theme for higher rated programs as well.

To block program content:

1.Determine the content themes you want to block.

2.Press the down arrow button to scroll to the rating whose content theme you want to change.

3.Press the right arrow button to move the highlight to a particular content theme status.

4.Press the OK button to change its status to B. (In the example to the left, you block the language (L) corresponding with TV-14. The language for TV-MA is blocked as well).

Notes: Broadcasters are not required to provide content themes or age-based ratings.

You must remember to activate Parental Controls for rating limits to take effect.

Using the TV???s Features

Viewing Specific Content Themes

If you block specific content themes, you have the option of going back and changing some of the content themes back to (V) View:

1.Determine the content themes you want to change to (V) View.

2.Press the down arrow button to scroll to the rating whose content theme you want to change, such as B under language (L) corresponding with TV-14.

3.Press the right arrow button to move the highlight to a particular content theme status.

4.Press the OK button to change the status back to V. Your child would then be able to watch programs with the TV-14 adult language content, but not programs with TV-MA language content.

Note: Only the content theme status corresponding to TV-14 (L) language changes to (V) View. Higher rated content themes, such as that for TV-MA language, do not change.

V-Chip Movie Rating Limit

Set movie rating limits by blocking movies rated above a specified level.

To access the Movie Rating menu:

1.Press MENU on the remote control (the MAIN MENU appears).

2.Select Parental Control.

3.Select USA V-Chip.

4.Select Movie Ratings.

Blocking Movie Ratings

Once you are in the Movie Rating Limit menu, follow these steps to block V-Chip Ratings:

1.Determine the rating you want to block.

2.Press the down arrow button to scroll to the rating you want to change.

3.Press the OK button to change its status to block (the lock icon appears and all ratings above the one you selected change to lock).

V-Chip Exempt Program Block

The Exempt Prgms. option lets you decide if programs that the V-Chip recognizes as unrated can be viewed. Unrated TV programs may include news, sports, political, religious, local and weather programs, emergency bulletins, public announcements, and programs without ratings.

Unlocked All unrated programs are available.

Locked All unrated programs are not available.

Note: You must remember to activate V-Chip for rating limits to take effect.

Press the down arrow button to highlight Exempt Prgms. Then press the right arrow button to toggle between the lock and unlock icon.

Using the TV???s Features

KidPass

The KidPass feature allows parents to set a certain amount of time every day of the week that a child can watch TV. To set KidPass:

1.Select Parental Control from the main menu.

2.Select KidPass (the KIDPASS menu appears with Current Day highlighted).

Note: If you can???t select KidPass, you need to set the time. Highlight Go Back, press the right arrow button, then select Time. Highlight Time, then enter the time using the number buttons.

3.Press the right arrow button to select the current day.

4.Press the down arrow button to choose the day of the week.

5.After you???ve chosen the day of the week, press the right arrow button to select the amount of time: Free and 00:30 up to 16:00 (30 minute increments).

6.When you???re done setting KidPass, select Go Back.

7.Highlight KidPass active and press the right arrow button to activate the KidPass settings (box has check mark). The KidPass takes effect immediately.

When the time has expired, the TV shuts off. If you turn on the TV the same day it shut off, the password screen appears (enter the password used for V-Chip).

V-Chip Active

Selecting this option lets you activate and deactivate parental control settings.

1.From the PARENTAL CONTROL menu, press the up or down arrow button to highlight V-Chip active.

2.Press the right or left arrow button to turn on (box has check mark) or off (box doesn???t have check mark) V-Chip active.

If you do not activate V-Chip, none of the settings for V-Chip will take effect.

If you forget your password you can reset it. Make sure the TV is off. Simultaneously press and hold VOL< on the TV???s front panel and CLEAR on the remote for approximately 5 seconds. Enter a new password the next time you access the PARENTAL CONTROL menu.

Front Panel Lock

Selecting this option lets you lock (disable) or unlock (enable) the TV???s front panel. The remote still tunes to any channel. When using this as a Parental Control method, remove access to any remote that is capable of operating the television.

1.From the PARENTAL CONTROL menu, press the up or down arrow button to highlight Lock Fr. Panel.

2.Press the right or left arrow button to turn on (box has check mark) or off (box doesn???t have check mark) front panel lock.

Change Password

Selecting this option lets you simply create a new password at any time. Once you enter a new password from Change Passwd. in the PARENTAL CONTROL menu it is the password you use until you change it again.

Chapter 4: Using the TV???s Menu System

Sound Menu

Treble Increases or decreases the treble.

Bass Increases or decreases the bass.

Balance Press the right arrow button to increase the audio output in the right speaker; press the left arrow button to increase the audio output in the left speaker.

Sound type Press the right arrow button to scroll through the available audio types, which control the way the sound comes through your speakers: Mono plays the sound in mono only. Use this setting when receiving broadcasts with weak stereo signals; Stereo to split the incoming stereo audio signal into left and right channels; and Enhanced for simulated surround sound. Most TV programs and recorded materials have stereo audio. The word Stereo appears on the TV when you tune to a program that is broadcast in stereo.

SAP (Second Audio Program) Plays the program???s audio in a second language, if one is available. The TV displays the word SAP when you tune to a program that is broadcast with SAP information. SAP audio is broadcast in mono. SAP is also used to broadcast a program???s audio with descriptions of the video for the visually impaired. Press OK to turn SAP on or off.

Auto Vol level (Auto Volume Level) Reduces the annoying blasts in volume during commercial breaks. Eliminates the need to constantly adjust volume control. Press OK to turn

Auto Vol level on or off.

Audio Output Press the right arrow button to scroll through the available output settings: Fixed allows fixed output from the TV???s audio output jacks to an external component, such as a surround sound amplifier; and Variable allows variable output from the TV???s audio output jacks.

Int. Speakers (Internal Speakers) Turns the TV???s internal speakers on or off. Turn off the internal speakers if you have an audio receiver or amplifier connected to the TV. Press OK to turn Int. Speakers on or off.

Note:T urningtheinternalspeakersoffdoesn???taffectAlertGuard. WhenanalarmsoundsorwhentheNWRisturnedon,AlertGuard willtemporarilyoverridethissetting.

Using the TV???s Menu System

20F670T, 27V570T, and 27F670T Picture menu

32F670T Picture menu

Picture Menu

The PICTURE menu options apply to the video for the main TV and video input selections.

Picture Preset Press the right arrow button to scroll through the available picture preset settings: Natural, Bright, Soft, and Personal. Choose the setting that is best for your viewing environment.

Auto Color Turn this option on to automatically correct the color of the picture. This is especially useful for tracking realistic flesh tone colors as you switch from channel to channel.

Color Warmth Press the right arrow button to scroll through the color adjustments: Cool for a more blue palette of picture colors; Normal; and Warm for a more red palette of picture colors.

Brightness Adjusts the brightness of the picture.

Contrast Adjusts the difference between the light and dark areas of the picture.

Color Adjusts the richness of the color.

Sharpness Adjusts the crispness of the edges in the picture.

Note:Sharpnessisn???tavailableforcomponentvideoinputchannels (CVID2orCVID3).

Tint Adjusts the balance between the red and green levels.

Note:Tintisn???tavailableforcomponentvideoinputchannels(CVID2 orCVID3).

When you change any of these picture settings, the Picture Preset changes to Personal. Use the left or right arrow button to make adjustments. To return to the PICTURE menu, press the up or down arrow button.

Tilt (Available only on model 32F670T) The TV has an extra large picture tube that makes it vulnerable to the effects of the Earth???s magnetic field. You may need to adjust the picture tilt.

Using the TV???s Menu System

Setup Menu

Auto Ch. Search (Auto Channel Search) Allows you to choose your signal type and begin an auto channel search.

Signal Type Press the left or right arrow button to select the signal your TV is receiving. Choose Cable if you are currently using cable or a cable box for TV signals. Choose Antenna if you are currently using an off-air antenna for TV signals.

Start Searches for channels the signal is receiving and stores them in the TV???s channel list. Go to page 9 for more information.

List & Labels Edit the channels in the list or choose labels for each channel. For example, if channel 12 is NBC, you can use this feature to label it NBC so it appears on-screen as part of the Channel Banner.

To delete a channel from the channel list, highlight Channel and use the left or right arrow button to select the channel. Then highlight In list and press the OK button. The box should no longer display a check mark.

To add a label to a channel, select the channel in the Channel option. Press the down arrow button to highlight Label. Press the right arrow button to highlight the first space. Use the up or down arrow button to ascend or descend through the characters. Continue to press the right arrow button to highlight the space and the up or down arrow button to add a character. Press OK when you???re finished adding a label.

Closed Caption Many programs are encoded with closed- captioning information, which lets you display the audio portion of a program as text on the TV screen.

Closed captioning is not available on all channels at all times. Only specific programs encoded with closed-captioning information are applicable. When a program is closed captioned, CC is displayed in the Channel Banner. Go to Chapter 3 for more information about the Channel Banner. The closed caption options are:

CC Display Lets you choose the way closed captioning information is shown on the screen.

Off No captioning information displayed.

On Captioning information always appears, when available.

Muted=On Displays captioning information, when available, whenever the TV???s sound is muted by pressing the MUTE button. The captioning information is not displayed when the sound is not muted.

Using the TV???s Menu System

CC Mode Choose which captioning mode is used for displaying captioning information. If you are unsure of the differences among the modes, you may prefer to leave the closed captioned mode set to CC1, which displays complete text of the program in the primary language in your area.

Auto Tuning Displays a choice list that lets you set up the TV to automatically tune to the correct video input channel when you press a component button (VCR1, VCR2, DVD, SAT???CABLE, etc.) on the remote. Go to Chapter 3 for details about the auto tuning feature.

Language Lets you select your preferred language for the menus, which you should have set in the Initial Setup. Go to page 9 for more information.

Parental Control Menu

The Parental Control menu was explained in Chapter 3. Go to page 24 for more information.

Time Menu

Sleep Timer Lets you set the TV to turn off after a given time. Press the right arrow button to add 15 minutes to the clock (up to four hours).

Time ref. Ch (Time reference Channel) Choose your PBS station to have the TV set the time for you.

Time Time is set if you select a reference channel (see above). If time is not obtained, then enter it manually. If it is 8:25, for example, you must first press the number 0 on the remote, then number 8, then 2 and then 5. Use the OK button to choose between AM and PM.

Wake-Up Timer Lets you set the TV to turn itself on.

Note:IftheTVturnsonbythewake-uptimerandnoremoteorfront panelbuttonsarepressedfor2hours ,theTVwillturnitselfoff.

Wake-Up Time Lets you set the time you want the TV to turn itself on.

Wake-Up Ch (Wake-Up Channel) Lets you select a specific channel the TV tunes to when the wake-up timer is set.

Alert Guard Menu

The Alert Guard menu was explained in Chapter 3. Go to page 18 for more information.

Chapter 5: Other Information

Troubleshooting

Most problems with your TV can be corrected by consulting the following troubleshooting list.

Note for U.S. customers: If you prefer, we can provide you with the name of an Authorized Service Representative who will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation. For details about this service, call 1-888-206-3359. For additional assistance while using your RCA product, please visit www.rca.com/customersupport.

Alert Guard Problems

NWR channel not clear

???Make sure you have connected the provided Alert Guard antenna to the EXT Alert Guard ANT jack on the back of the TV. Go to page 8 for more information.

???You might be tuned to an NWR channel outside your immediate area. Go to the NWR CHANNEL menu to check all NWR channels receiving local area forecasts. Select the channel that sounds most appropriate.

???If the signal???s still not clear, you might need to connect an outdoor or amplified antenna to the EXT Alert Guard ANT jack on the back of the TV. For optimal reception, connect an outdoor antenna. Use an amplified antenna if you can???t connect an outdoor antenna. Go to page 59 to purchase an amplified antenna.

Not getting local weather information from the NWR channel

???Make sure the NWR channel is set to a local channel.

Message on-screen that READY light is out and NWR channel can???t send alerts for My Area

???You might be tuned to an NWR channel outside your immediate area. Go to the NWR CHANNEL menu to check all NWR channels receiving forecasts for your local area. If several channels sound equally as good, pick the one with your local forecast.

???You might have set My Area to a location where the TV isn???t located. For example, you might live in Indiana, but have a cottage in Ottawa County, Michigan. If the TV is in Michigan, you need to set the state of My Area to Michigan and the county to Ottawa County. Go to the Alert Guard menu and select Locations to check My Area setting.

???In rare cases, the NWR channel might not serve your area (generally, rural areas). From the LOCATIONS menu select the next closest area to you or choose your state and select All nearby.

Message on-screen that READY light is out and no weekly test was received

???If you live in an area that generally does not receive good reception and you???ve tried setting a different NWR channel, you might need to connect an outdoor or amplified antenna to the EXT Alert Guard ANT jack on the back of the TV. For optimal reception, connect an outdoor antenna. Use an amplified antenna if you can???t connect an outdoor antenna. Go to page 59 to purchase an amplified antenna.

???If weather conditions are bad for several consecutive days, NOAA might not have been able to broadcast a test. If so, press CLEAR after receiving the message and check in a few days to see if the green READY light is back on. If the problem persists, the message will appear again in 9 days. Failure to fix the problem could result in alerts not being received.

Message on-screen that areas were removed

???NWR channel can???t provide information for locations Nearby 1, 2, or 3 (areas set in the LOCATIONS menu) if they???re outside the reception area.

Other Information

Message on-screen that I might have missed alerts

???Check the green light. If on, the signal might have been lost momentarily due to interference.

???The NWR channel might be too weak. Press the HEAR VOICE button on the remote. If it???s not clear, you need to search for a stronger channel in the NWR CHANNEL menu. If you???re already receiving the strongest channel, connect an external or amplified antenna to the EXT Alert Guard ANT jack on the back of the TV. For best reception, the external antenna should be located outside your home.

Message on-screen that power was interrupted

???The TV can???t receive alerts during a power outage. Press the HEAR VOICE button once power is restored to hear any alerts that might have been issued.

Message seen option not working

???The TV can???t display the message when the TV is off. Press the VIEW MESSAGE button to view the alert.

Receiving too many alerts

???Go to the Alert Guard menu and select Locations. Check all the locations you set. If you???ve chosen All of U.S. or All nearby, you might want to select a specific area.

???If all four locations have been set in the LOCATIONS menu, consider setting Nearby 1, 2 and 3 to No Area. Highlight the state you set for these areas and then press the left or right arrow button to choose No Area (it is listed before Alabama and after St. Lawrence River.

TV Problems

TV won???t turn on

???Press the TV button.

???Make sure the TV is plugged in.

???Check the wall receptacle (or extension cord) to make sure it is ???live??? by plugging in something else.

???Something might be wrong with your remote control. Press the POWER button on the front of the TV. If the TV turns on, check the remote control solutions on page 35.

???The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Lock Fr. Panel in the PARENTAL CONTROL menu and press OK (box won???t have check mark).

Buttons don???t work

???If you???re using the remote control, press the TV button first to make sure the remote is in TV mode.

???The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Lock Fr. Panel in the PARENTAL CONTROL menu and press OK (box won???t have check mark).

???Unplug the TV for two minutes and then plug it back in. Turn the TV on and try again.

TV turns off unexpectedly

???Sleep timer may have been activated. Go to page 32 for instructions.

???KidPass may have been activated. Go to page 28 for instructions.

???Wake-up timer turned on the TV and no remote or front panel buttons were pressed for two hours.

Other Information

???Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on again. If this happens frequently, the voltage in your house may be abnormally high or low.

???Unplug TV. Wait five minutes. Plug it in again.

TV turns on unexpectedly

???Wake-up timer might have been activated. Go to page 32 for instructions.

???You might have pressed CH+, CH- or OK on the remote accidentally.

Blank screen

???Make sure you have connected the component to the TV correctly.

???Make sure the component connected to the TV???s turned on and the TV???s tuned to the corresponding video input channel.

???Try another channel.

No sound, picture okay

???Maybe the sound is muted. Try pressing the volume up button to restore sound.

???Make sure the audio cables are fully connected to the AUDIO input jacks.

???If using S-Video or Y, PB, PR, remember to also connect the component???s left and right audio output jacks to the TV???s AUDIO input jacks.

???Make sure the Int. Speakers option in the SOUND menu is turned on.

Can???t select certain channel

???Channel may be blocked or not approved through the V-Chip.

???If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR).

Noisy stereo reception

???May be a weak station. Access the SOUND menu, highlight Sound Type and then choose Mono.

No picture/blue screen, no sound but TV is on

???Maybe the signal type is set wrong. Go to page 31 for detailed instructions.

???The channel might be blank ??? change channels.

???If you???re watching your VCR and it???s connected with a coaxial cable to the TV ANT jack, tune the TV to channel 3 or 4 (whichever channel is selected on the 3/4 switch on the back of your VCR). Also check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR).

Sound okay, picture poor

???Check antenna and video connections. Make sure all of the cables are firmly connected to the jacks.

???Try adjusting the sharpness function to improve weak signals. Go to page 30 for more instructions.

Black box appears on the screen

???Closed-captioning might be on. Check Closed Caption in the Setup menu. Go to page 31 for more instructions.

PASSWORD menu appears

???KidPass option is activated and you try to reset the time.

???You turn the TV on after KidPass shut off the TV.

Other Information

The Remote Control Doesn???t Work

???Something might be between the remote and the remote sensor on the component. Make sure there is a clear path.

???Maybe the remote isn???t aimed directly at the component (TV or VCR) that you???re trying to operate.

???Maybe remote is not in TV Mode. Press the TV button so remote will control TV.

???Maybe batteries in remote are weak, dead, or installed incorrectly. Put new batteries in the remote. (Note, if you remove the batteries, you may have to reprogram the remote to operate other components.)

???You might need to reset the remote: remove batteries and press the number 1 button for at least 60 seconds. Release the 1 button, replace the batteries, and (if necessary) program the remote again.

Problems with V-Chip/Parental Controls

The rating limits don???t work

???You must lock the settings. Go to the MAIN MENU (press MENU on your remote), select

Parental Control, select V-Chip active.

I don???t remember my password and I want to unlock the TV

???If you forget your password you can reset it. Make sure the TV is off. Simultaneously press and hold VOL< on the TV???s front panel and CLEAR on the remote for approximately 5 seconds. Enter a new password the next time you access the PARENTAL CONTROL menu.

The V-Chip won???t let me watch a program even though it???s not rated as violent

???Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to View separately in order to view movies with an NR rating.

Care and Cleaning

CAUTION: Turn OFF your TV before cleaning.

You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet to help assure adequate ventilation.

The TV???s screen may be cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar the screen. If necessary, you may use a cloth dampened with warm water. Never use strong cleaning agents, such as ammonia-based cleaners, or abrasive powder. These types of cleaners will damage the TV.

While cleaning do not spray liquid directly on the lights on the front of the TV, on the screen, or allow liquid to run down the screen and inside the TV. Also, never place drinks or vases with water on top of the TV. This could increase the risk of fire or shock hazard or damage to the TV.

Caution: Using video games or any external accessory with fixed images for extended periods of time can cause them to be permanently imprinted on the picture tube (or projection TV picture tubes). ALSO, some network/program logos, phone numbers, etc. may cause similar damage. This damage is not covered by your warranty.

Other Information

Alert Guard Location Codes

If you can???t find your location code, call 1-888-NWR-SAME

Alabama Counties

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Tolland009013

Windham 009015

Delaware Counties

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Massachusetts Counties

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Northern Mariana Islands

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

If you can???t find your location code, call 1-888-NWR-SAME

Other Information

Limited Warranty (for models 20F670T, 27F670T and 32F670T)

What your warranty covers:

???Defects in material or workmanship.

For how long after your purchase:

???One year from date of purchase for labor charges.

???One year from date of purchase for parts.

???Two years from date of purchase for picture tube.

The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first.

What we will do:

???Pay any Authorized RCA Television Service Center the labor charges to repair your television.

???Pay any Authorized RCA Television Service Center for the new or, at our option, rebuilt replacement parts and picture tube required to repair your television.

How you get service:

???For 20??? screen size: Take your RCA television to any Authorized RCA Television Service Center and pickup when repairs are complete.

???For screen sizes larger than 20???: Request home or pick up, repair and return service from any Authorized RCA Television Service Center, provided that your television is located within the geographic territory covered by an Authorized RCA Television Service Center. If not, you must take your television to the Service Center location at your own expense, or pay for the cost the Service Center may charge to transport your television to and from your home.

???To identify your nearest Authorized RCA Service Center, ask your dealer, visit www.rca.com, look in the Yellow Pages, or call 1-800-336-1900.

???Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.

What your warranty does not cover:

???Customer instruction. (Your Owner???s Manual describes how to install, adjust, and operate your product. Any additional information should be obtained from your dealer.)

???Installation and related adjustments.

???Signal reception problems not caused by your television.

???Damage from misuse or neglect.

???Batteries.

???Customer replacement fuses.

???Damage from images burnt onto the screen.

???A television that has been modified or incorporated into other products or is used for institutional or other commercial purposes.

???Acts of nature, such as but not limited to lightning damage.

???A television purchased or serviced outside the U.S.A.

Other Information

Product Registration:

???Please complete and mail the Product Registration Card packed with your TV or register on-line at www.rca.com/productregistration. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.

Limitation of Warranty:

???THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO

VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

???REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF

THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF

ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES

AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO

THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE

WARRANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

???Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

???This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.

If you purchased your product outside the United States:

???This warranty does not apply. Contact your dealer for warranty information.

Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such service calls are the sole responsibility of the purchaser.

Other Information

Limited Warranty (for model 27V570T)

What your warranty covers:

???Defects in material or workmanship.

For how long after your purchase:

???90 days from date of purchase for labor charges.

???One year from date of purchase for parts.

???Two years from date of purchase for the picture tubes.

The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.

What we will do:

???Pay any Authorized RCA Television Service Center the labor charges to repair your television.

???Pay any Authorized RCA Television Service Center for the new or, at our option, rebuilt replacement parts and picture tube required to repair your television.

How you get service:

???For 20??? screen size: Take your RCA television to any Authorized RCA Television Service Center and pickup when repairs are complete.

???For screen sizes larger than 20???: Request home or pick up, repair and return service from any Authorized RCA Television Service Center, provided that your television is located within the geographic territory covered by an Authorized RCA Television Service Center. If not, you must take your television to the Service Center location at your own expense, or pay for the cost the Service Center may charge to transport your television to and from your home.

???To identify your nearest Authorized RCA Service Center, ask your dealer, visit www.rca.com, look in the Yellow Pages, or call 1-800-336-1900.

???Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.

What your warranty does not cover:

???Customer instruction. (Your Owner???s Manual describes how to install, adjust, and operate your product. Any additional information should be obtained from your dealer.)

???Installation and related adjustments.

???Signal reception problems not caused by your television.

???Damage from misuse or neglect.

???Batteries.

???Customer replacement fuses.

???Damage from images burnt onto the screen.

???A television that has been modified or incorporated into other products or is used for institutional or other commercial purposes.

???Acts of nature, such as but not limited to lightning damage.

???A television purchased or serviced outside the U.S.A.

Other Information

Product Registration:

???Please complete and mail the Product Registration Card packed with your TV or register on-line at www.rca.com/productregistration. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.

Limitation of Warranty:

???THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO

VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

???REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF

THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF

ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES

AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO

THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE

WARRANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

???Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

???This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.

If you purchased your product outside the United States:

???This warranty does not apply. Contact your dealer for warranty information.

Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such service calls are the sole responsibility of the purchaser.

Other Information

ALERT GUARD

VIEW HEAR STOP NEWS

MESSAGE VOICE ALARM WEATHER

RCR160THM1

VH47

Remote Control This is the remote control that came packed with your TV. Replacements or spares can be ordered as needed.

2-way Signal Splitter

helps you connect to a second TV or VCR.

Amplified VHF/UHF/FM Antenna allows you to easily switch from the antenna signal to cable

Prices are subject to change without notice.

ANT200

or satellite easily without disconnecting antenna.

Component Video Cables Triple cable used to connect a video source with

Y, Pr, Pb jacks to the TV.

VH913

SCTV4000C

S-Video Cable has multi- pin connectors on each end for connecting S- Video components to your TV.

Surge Protector provides eight outlets, coaxial and telephone line protection. Audible alarm for surge failure.

DT6DC (6-ft)

DT12DC (12-ft)

VH81 (3-ft)

VH82 (6-ft)

VH83

Screw-on Cable attaches to the round antenna connectors (called 75-ohm F-type) on the back of your VCR or TV. The ends screw onto the connectors for a secure connection.

Standard Audio/Video cable with RCA-type phono plugs.

HOW TO ORDER

ON-LINE: Accessories may also be purchased at www.rca.com/accessories (subject to availability). BY PHONE: To place your order by phone, have your Visa, MasterCard or Discover Card ready and call 1-800-338-0376. Use this number only to place an order for accessory items listed on this page.

All accessories are subject to availability.

Where applicable, we will ship a superseding model.

Televison Receiver

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

FCC Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Trade Name: RCA

Model(s): 20F670T, 27V570T, 27F670T, 32F670T

Equipment Classification: Radio receiver subject to part 15 of the FCC regulations

Responsible Party: Thomson Inc.

10330 N. Meridian St.

Indianapolis, IN 46290

Telephone 1-580-634-0151

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio/TV technician for help.

Visit the RCA web site at www.rca.com

Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in service for your product.

Thomson Inc.

10330 North Meridian Street

Indianapolis, IN 46290

??2003 Thomson Inc.

Trademark(s)?? Registered