R

Instruction Manual Manual de Instrucciones Manuel d???Instructions

PBV200 LE

ENGLISH

IMPORTANT MANUAL - Do not throw away MANUAL IMPORTANTE - No lo descarte MANUEL IMPORTANT - ?? Conserver

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

AVERTISSEMENT:

Veuillez lire le manuel d???instructions et bien respecter tous les avertissements et toutes les instructions de s??curit??. Tout d??faut de le faire pourrait entra??ner des blessures graves.

Electrolux Home Products, Inc.

104 Warren Road

Augusta, GA 30907

ESPA??OL

FRAN??AIS

SAFETY RULES

WARNING: Failure to follow all

Safety Rules and Precautions can result in serious injury.

KNOW YOUR UNIT

SRead your instruction manual carefully until you completely understand and can follow all warnings and safety rules before operat-

ing the unit.

DRestrict unit to users who understand and will follow all warnings and safety rules in this manual.

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can rico- chet, be thrown, or otherwise cause injury or damage during operation.

Use your unit as a blower for:

DSweeping debris or grass clippings from driveways, sidewalks, patios, etc.

DBlowing grass clippings, straw, or leaves into piles, around joints, or between bricks.

Use your unit as a vacuum for:

D Picking up dry material such as leaves, grass, small twigs, and bits of paper.

DFor best results during vacuum use, operate your unit at high speed.

DMove slowly back and forth over the mate- rial as you vacuum. Avoid forcing the unit

into a pile of debris as this can clog the unit.

DKeep the vacuum tube about an inch above the ground for best results.

PLAN AHEAD

DAlways wear eye protection when operat- ing, servicing, or performing maintenance on unit. Wearing eye protection will help to prevent rocks or debris from being blown or ricocheting into eyes and face which can result in blindness and/or serious injury.

Eye protection should be marked Z87.

D Always wear foot protection. Do not go barefoot or wear sandals.

D Always wear respirator or face mask when working with unit in dusty environments.

DSecure hair above shoulder length. Secure or remove jewelry, loose clothing, or cloth- ing with loosely hanging straps, ties, tas- sels, etc. They can be caught in moving

parts.

DDo not operate unit when you are tired, ill, up- set, or if you are under the influence of alco-

hol, drugs, or medication.

D Keep children, bystanders, and animals

away from work area a minimum of 30 feet (10 meters) when starting or operating unit. Do not point the blower nozzle in the direc- tion of people or pets.

HANDLE FUEL WITH CAUTION, IT IS

HIGHLY FLAMMABLE

DEliminate all sources of sparks or flame (in- cluding smoking, open flames, or work that can cause sparks) in the areas where fuel is mixed, poured, or stored.

DMix and pour fuel in an outdoor area; store fuel in a cool, dry, well ventilated place; use an approved, marked container for all fuel

purposes.

D Do not smoke while handling fuel or while operating the unit.

DMake sure the unit is properly assembled and in good operating condition.

D Do not fill fuel tank while engine is hot or

running.

D Avoid spilling fuel or oil. Wipe up fuel spills before starting engine.

D Move at least 10 feet (3 meters) away from fuel and fueling site before starting engine.

D Always store gasoline in a container ap- proved for flammable liquids.

OPERATE YOUR UNIT SAFELY

WARNING: Stop the engine before

opening the vacuum inlet door. The engine must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.

D Inspect unit before each use for worn, loose, missing, or damaged parts. Do not use until unit is in proper working order.

D Keep outside surfaces free of oil and fuel.

DNever start or run engine inside a closed room, building or other unventilated area.

Breathing exhaust fumes can kill.

D To avoid static electricity shock, do not wear rubber gloves or any other insulated gloves while operating unit.

D Do not set unit on any surface except a clean, hard area while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and

thrown out through discharge opening, damaging unit, property, or causing serious injury to bystanders or operator.

DAvoid dangerous environments. Do not use in unventilated areas or where explosive vapors or carbon monoxide build up could be present.

DDo not overreach or use from unstable sur- faces such as ladders, trees, steep slopes, rooftops, etc. Keep firm footing and balance at all times.

D Never place objects inside the blower tubes; always direct the blowing debris away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or

cause other damage.

DNever run unit without the proper equip- ment attached. When using your unit as a blower, always install blower tubes. When using your unit as a vacuum, always install vacuum tubes and vacuum bag assembly. Make sure vacuum bag assembly is com-

pletely zipped.

DCheck air intake opening, blower tubes, vacuum tubes, and elbow tube frequently, always with engine stopped and spark

-- 2 --

Small Opening
Rib

plug disconnected. Keep vents and dis- charge tubes free of debris which can ac- cumulate and restrict proper air flow.

DNever place any object in the air intake opening as this could restrict proper air flow

and cause damage to the unit.

DNever use for spreading chemicals, fertil- izers, or other substances which may con-

tain toxic materials.

DTo avoid spreading fire, do not use near leaf or brush fires, fireplaces, barbecue

pits, ashtrays, etc.

D Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

DHave all maintenance other than the rec- ommended procedures described in the in-

struction manual performed by an autho- rized service dealer.

D Disconnect spark plug before performing maintenance except for carburetor adjust-

ments.

DUse only recommended Poulan PROR re- placement parts; use of any other parts

may void your warranty and cause damage to your unit.

DEmpty fuel tank before storing the unit. Use up fuel left in carburetor by starting engine and

letting it run until it stops.

D Do not use any accessory or attachment other than those recommended by manufac- turer for use with your unit.

DDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric

motors or switches, furnaces, etc.

D Store in a dry area out of reach of children.

SPECIAL NOTICE: Exposure to vibra-

tions through prolonged use of gasoline pow- ered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood vessel dam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark arresting screen which meets the require- ments of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Ore- gon, and Washington require by law that many internal combustion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the MAINTENANCE section for information on maintenance of the muffler and spark arrest- ing screen.

ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

WARNING: If you receive your unit

assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit.

DA standard screwdriver is required for as- sembly.

BLOWER TUBE ASSEMBLY

1.Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place.

NOTE: Knob must be loose enough to allow blower tube to be inserted in blower outlet. Loosen knob by turning counterclockwise.

Blower

Outlet Blower

Tube

Groove Rib

2.Secure the tube by turning the knob clock- wise.

3.To remove the tube, turn the knob counter- clockwise to loosen the tube; remove the tube.

VACUUM BAG ASSEMBLY

1.Open the zipper on the vacuum bag and insert the elbow tube.

2.Push the small end of the elbow tube

through the small opening in the bag. Elbow

Tube

Zipper

Opening

-- 3 --

NOTE: Make sure edge of the small opening

is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom.

3.Close the zipper on the bag. Make sure the zipper is closed completely.

4.Remove blower tube from engine.

Rib

Groove

5.Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove.

6.Turn knob clockwise to secure elbow tube.

VACUUM TUBE ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury.

1.Align the lower vacuum tube as shown. Push lower vacuum tube into upper vacu- um tube.

Upper Vacuum

Tube

Lower Vacuum Tube

2.Insert the tip of a screwdriver into the latch area of the vacuum inlet.

3.Gently tilt the handle of the screwdriver to- ward the back of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand.

4.Hold the vacuum inlet cover open until up- per vacuum tube is installed.

Vacuum Inlet

Retaining Post

Vacuum

Inlet

Cover

5.Place the hooks of the upper vacuum tube on the retaining posts of the unit.

6.Pivot the tube until it is secured to the blower unit by the vacuum inlet latch.

PIVOT Inlet Cover

Latch

HookRetaining

Post

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1.Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area of the vacuum inlet.

2.Gently tilt handle of screwdriver toward the back of the unit to release the latch while pulling up on the upper vacuum tube with your other hand.

Latch Area

3.Remove the vacuum bag.

4.Close the vacuum inlet cover and make sure it is latched closed.

5.Reinstall the blower tube (see BLOWER

TUBE ASSEMBLY).

-- 4 --

SHOULDER STRAP ADJUSTMENT

1.Hold the unit as shown with the muffler side facing away from your body and clothes.

2.Pass the shoulder strap over your head and onto your right shoulder.

3.Extend your left arm toward the rear of the vacuum bag.

4.Adjust shoulder strap until the vacuum bag/shoulder strap seam lies between your thumb and index finger.

5.Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate properly.

OPERATION

KNOW YOUR BLOWER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

THROTTLE LEVER

The THROTTLE LEVER is used to select the desired engine speed and to stop the engine.

full speed operation. Move the throttle lever

to the position for idle speed. To stop the

engine, move the throttle lever to the STOP position.

PRIMER BUTTON

The PRIMER BUTTON removes air from the

carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate primer button by pressing it and allowing it to return to its origi- nal position.

CHOKE LEVER

The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After engine attempts to start, move the choke lever to the HALF CHOKE position. Once engine starts, move choke lever to the RUN position.

-- 5 --

OPERATING POSITION

Eye

Protection

BlowerVacuum

OPERATING TIPS

S While vacuuming or blowing debris, hold the unit with the muffler side facing away from your body and clothes (see OPERAT- ING POSITION illustration above).

S To reduce the risk of hearing loss associated with sound level(s), hearing protection is required.

STo reduce the risk of injury associated with contacting rotating parts, stop the engine be- fore installing or removing attachments. Do not operate without guard(s) in place.

SOperate power equipment only at reasonable hours--not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. Usual recom- mendations are 9:00 a.m. to 5:00 p.m.,

Monday though Saturday.

S To reduce noise levels, limit the number of pieces of equipment used at any one time.

S To reduce noise levels, operate power blowers at the lowest possible throttle speed to do the job.

S Use rakes and brooms to loosen debris be- fore blowing.

S In dusty conditions, slightly dampen sur-

faces or use a mister attachment when wa- ter is available.

S Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters,

screens, patios, grills, porches, and gardens. S Watch out for children, pets, open windows, or freshly washed cars. Blow debris away

safely.

SUse the full blower nozzle extension so the air stream can work close to the ground.

SAfter using blowers and other equipment, CLEAN UP! Dispose of debris in trash re- ceptacles.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you be-

gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan PROR brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1

ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

NOTE: Unit must be placed on its side when adding fuel (see illustration below).

TO STOP THE ENGINE

DTo stop the engine, move the throttle lever to the STOP position.

BEFORE STARTING THE ENGINE

WARNING: You MUST make sure the tubes are secure before using the unit.

DFuel engine. Move at least 10 feet (3 me- ters) away from the fueling site.

-- 6 --

DHold the unit in the starting position as shown. Make sure the blower end is di- rected away from people, animals, glass, and solid objects.

STARTING POSITION

Blower

Vacuum

WARNING: When starting engine,

hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such

as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

1.Move throttle lever to the position.

2.Move choke lever to the FULL CHOKE position.

3.Slowly press the primer button 8 times.

Choke Lever

4.Pull starter rope sharply until engine at- tempts to run, but no more than 5 pulls (be- low 30_ F, 8 pulls).

NOTE: If engine attempts to start before the 5th pull, go to next step immediately.

5.Move the choke lever to the HALF CHOKE position.

6.Pull the starter rope sharply until the en- gine runs, but no more than 5 pulls (below 30_ F, 10 pulls).

7.After a 5 second warm--up, move the choke lever to the RUN position.

8.Allow the unit to run for 30 more seconds at the RUN position before moving the throttle lever to the position.

If engine has not started after 5 pulls (at HALF

CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE.

9.To stop the engine, move the throttle lever to the STOP position.

STARTING A WARM ENGINE

NOTE: If fuel tank is empty, add fuel; then, follow STARTING A COLD ENGINE proce- dure. Do not fill fuel tank while engine is hot.

1.Move throttle lever to the position.

2.Pull starter rope sharply until engine runs, but no more than 5 pulls.

NOTE: If engine has not started, pull starter

rope 5 more pulls. If engine still does not run, it is probably flooded.

3.To stop the engine, move the throttle lever to the STOP position.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position. Move throttle

lever to the fast position ; then, pull rope until engine starts. After engine starts, move the

Starting could require pulling the starter rope many times depending on how badly the unit is flooded.

If unit still doesn???t start refer to the TROUBLE- SHOOTING TABLE or call 1-800-554-6723.

-- 7 --

MAINTENANCE

WARNING: Avoid touching muffler

unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac-

cessing movable parts.

HELPFUL TIP

IMPORTANT: Have all

CLEAN AIR FILTER

Air Filter

Cover

repairs other than the rec- ommended maintenance described in the instruction manual performed by an

Air Filter

Screws

authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Electrolux Home Products, Inc., may not pay for repairs under war- ranty. It is your responsibility to maintain and perform general maintenance.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

S Spark Plug Boot

S Air Filter

S Housing Screws

S Muffler

CHECK FOR DAMAGED OR WORN

PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

S Fuel Tank -- Do not use unit if fuel tank shows signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

INSPECT AND CLEAN UNIT AND

DECALS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild deter-

gent.

S Wipe off unit with a clean dry cloth.

Cleaning the air filter:

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean or replace air filter after every 5 hours of operation or yearly, whichever comes first.

1.Clean the cover and the area around it to keep debris from falling into the carburetor chamber when the cover is removed.

2.Remove parts as illustrated.

NOTE: Do not clean filter in gasoline or other flammable solvent. Doing so can create a fire hazard or produce harmful evaporative emis- sions.

3.Wash the filter in soap and water.

4.Allow filter to dry.

5.Apply a few drops of oil to the filter; squeeze filter to distribute oil.

6.Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch. Ignition timing is

fixed, nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and dis- card.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch socket wrench.

4.Reinstall the spark plug boot.

REPLACE FUEL FILTER

To replace fuel filter, drain unit by running it dry of fuel, then remove fuel cap/retainer assem- bly from tank. Pull filter from tank and remove

it from the fuel line. Install new fuel filter on fuel line; reinstall parts.

-- 8 --

Fuel Line

Fuel Filter

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting

screws are secure and tightened properly to prevent damage.

Mounting Screw

Screws

1.Loosen and remove the 2 screws from the muffler cover.

2.Remove the muffler cover.

3.Tighten the 2 muffler mounting screws se- curely.

4.Reinstall muffler cover and 2 screws. Tighten securely.

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

WARNING: The muffler on this prod- uct contains chemicals known to the State of

California to cause cancer.

As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire

hazard or affecting engine performance.

VIEW OF MUFFLER

Spark arresting screen

Exhaust

Diverter

Screws

Replace the spark arresting screen every 50 hours of operation or if any damage or breaks in the screen are noted.

NOTE: Do not attempt to clean the spark ar- resting screen.

1.Loosen and remove the 2 screws from the muffler cover. Remove the muffler cover.

2.Loosen and remove both screws from the exhaust diverter.

3.Remove the exhaust diverter and spark

arresting screen.

4 Install new spark arresting screen.

5.Reinstall exhaust diverter and both screws. Tighten screws securely.

6.Reinstall muffler cover and 2 screws. Tighten securely.

NOTE: If any part of the muffler is cracked,

broken or damaged, we recommend that the muffler be replaced.

CARBURETOR ADJUSTMENTS

There is no screw for idle adjustment on your blower. The throttle lever is used to control engine speed. The throttle lever can be placed in one of four positions: STOP, IDLE

intermittent position. If your engine will not run properly or you require further assistance, contact an authorized service dealer or call

1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run

engine at least 5 minutes after adding stabilizer.

-- 9 --

HELPFUL TIP

During storage of your gas/

oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

S Clean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

S Replace your gasoline can if it starts to rust.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing any of the recommended remedies below other than remedies that require operation of the unit.

-- 10 --

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS, INC., warrants to the original purchaser that each new Poulan PROR brand gasoline tool or attach- ment is free from defects in material and work- manship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of

purchase:

2 YEARS - Parts and Labor, when used for household purposes.

90 DAYS - Parts and Labor, when used for commercial, professional, or income producing purposes.

30 DAYS - Parts and Labor, if used for rental purposes.

This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance, or the use of accessories and/or attachments not specifically recommended by ELECTROLUX HOME

PRODUCTS, INC., for this tool. Additionally, this warranty does not cover tune-ups, spark plugs, filters, starter ropes, starter springs, cut- ting line, or rotating head parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not

cover predelivery setup or normal adjustments explained in the instruction manual.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELECTROLUX HOME PROD- UCTS, INC., is to continuously improve its

products. Therefore, ELECTROLUX HOME PRODUCTS, INC., reserves the right to change, modify, or discontinue models, de- signs, specifications, and accessories of all products at any time without notice or obliga- tion to any purchaser.

U.S. EPA/CALIFORNIA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGA-

TIONS: The U.S. Environmental Protection

Agency/California Air Resources Board and ELECTROLUX HOME PRODUCTS, INC., are pleased to explain the emissions control system warranty on your year 2002--2004 small off--

road engine. In California, all small off--road en- gines must be designed, built, and equipped to meet the State???s stringent anti--smog standards.

ELECTROLUX HOME PRODUCTS, INC.,

must warrant the emission control system on your small off--road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off--road engine. Your emission con- trol system includes parts such as the carbure- tor and the ignition system. Where a warrant- able condition exists, ELECTROLUX HOME PRODUCTS, INC., will repair your small off--

road engine engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor. MANUFACTURER???S WAR- RANTY COVERAGE: If any emissions related

part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a de- fect in the materials or workmanship of the en- gine causes the failure of such an emission re- lated part, the part will be repaired or replaced by ELECTROLUX HOME PRODUCTS, INC.

OWNER???S WARRANTY RESPONSIBILI- TIES: As the small off--road engine engine own- er, you are responsible for the performance of the required maintenance listed in your instruc- tion manual. ELECTROLUX HOME PROD- UCTS, INC., recommends that you retain all re-

ceipts covering maintenance on your small off--

road engine, but ELECTROLUX HOME PRODUCTS, INC., cannot deny warranty sole- ly for the lack of receipts or for your failure to en- sure the performance of all scheduled mainte- nance. As the small off--road engine engine owner, you should be aware that ELECTRO-

LUX HOME PRODUCTS, INC., may deny you warranty coverage if your small off--road engine engine or a part of it has failed due to abuse, ne- glect, improper maintenance, unapproved mod-

ifications, or the use of parts not made or ap- proved by the original equipment manufacturer. You are responsible for presenting your small off--road engine to an ELECTROLUX HOME PRODUCTS, INC., authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and re-

sponsibilities, you should contact your nearest authorized service center or call ELECTRO- LUX HOME PRODUCTS, INC., at 1--800--554--6723. WARRANTY COM-

MENCEMENT DATE: The warranty period be- gins on the date the small off--road engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of purchase. WHAT IS COV-

ERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of any war- ranted part will be performed at no charge to the owner at an approved ELECTROLUX HOME PRODUCTS, INC., servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact

your nearest authorized service center or call

-- 11 --

ELECTROLUX HOME PRODUCTS, INC., at 1--800--554--6723 WARRANTY PERIOD: Any warranted part which is not scheduled for re- placement as required maintenance, or which is scheduled only for regular inspection to the ef- fect of ???repair or replace as necessary??? shall be warranted for 2 years. Any warranted part which

is scheduled for replacement as required main- tenance shall be warranted for the period of time up to the first scheduled replacement point for that part. DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective if the diagnostic work is performed at an ap- proved ELECTROLUX HOME PRODUCTS, INC., servicing center. CONSEQUENTIAL

DAMAGES: ELECTROLUX HOME PROD-

UCTS, INC., may be liable for damages to other engine components caused by the failure of a warranted part still under warranty. WHAT IS NOT COVERED: All failures caused by abuse, neglect, or improper maintenance are not cov- ered. ADD-ON OR MODIFIED PARTS: The use of add--on or modified parts can be grounds for disallowing a warranty claim. ELECTRO- LUX HOME PRODUCTS, INC., is not liable to

cover failures of warranted parts caused by the use of add--on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you

should contact your nearest authorized service center or call ELECTROLUX HOME PROD-

UCTS, INC., at 1--800--554--6723. WHERE TO GET WARRANTY SERVICE: Warranty ser-

vices or repairs shall be provided at all ELEC- TROLUX HOME PRODUCTS, INC., service centers. call: 1--800--554--6723 MAINTE-

NANCE, REPLACEMENT AND REPAIR OF

EMISSION RELATED PARTS: Any ELEC-

TROLUX HOME PRODUCTS, INC., approved replacement part used in the performance of

any warranty maintenance or repair on emis-

sion related parts will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS

LIST: Carburetor, Ignition System: Spark Plug (covered up to maintenance schedule), Ignition Module, Muffler including catalyst. MAINTE- NANCE STATEMENT: The owner is responsi-

ble for the performance of all required mainte- nance as defined in the instruction manual.

This engine is certified to be emissions compliant for the following use: Moderate (50 hours)

Intermediate (125 hours) Extended (300 hours)

-- 12 --