R

Please do not return product to retailer.

Por favor, no devuelva el producto al lugar de compra. Veuillez ne pas retourner le produit au d??taillant.

1-800-554-6723

Register your product online at: Registre su producto en l??nea en:

Enregistrez votre produit en ligne ?? l???adresse :

www.poulanpro.com

Instruction Manual

Manual de Instrucciones

Manuel d???Instructions

BVM200VS

IMPORTANT MANUAL - Do not throw away MANUAL IMPORTANTE - No lo descarte MANUEL IMPORTANT - ?? Conserver

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

AVERTISSEMENT:

Veuillez lire le manuel d???instructions et bien respecter tous les avertissements et toutes les instructions de s??curit??. Tout d??faut de le faire pourrait entra??ner des blessures graves.

ENGLISH

ESPA??OL

FRAN??AIS

IDENTIFICATION OF SAFETY SYMBOLS

WARNING: This unit can be dangerous! Careless or improper use can cause serious injury.

WARNING: Read the operator???s manual before use. Failure to

follow instructions could result in serious injury to the operator and/or bystanders. Save operator???s manual.

The blower can throw objects vio- lently. You can be blinded or injured.

Always wear hearing protection and safety glasses marked Z87. Always wear heavy, long pants, long sleeves, boots and gloves.

Hazard zone for thrown objects. Keep children, by- standers, and animals away from work area a mini-

mum of 30 feet (10 meters) when starting or operating unit. Do not point blower nozzle in the direction of people or pets.

Secure hair above shoulder length. Do not wear jewelry, loose clothing, or clothing with loosing hanging straps, ties, tassels, etc. They can be caught in moving parts.

Always stop unit and disconnect spark plug before cleaning or servicing.

WARNING: Stop the engine before opening the vacuum inlet door. The engine must

be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. Gently tilt the handle of the screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand.

-- 2 --

IDENTIFICATION OF SAFETY SYMBOLS

When using the vacuum attachment, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not

vacuum stones, gravel, metal, broken glass, etc., to avoid severe dam- age to the impeller.

WARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or work that can cause sparks).

WARNING: The muffler is very hot during and after use. Do

not touch the muffler, muffler guard, or surrounding surfaces, or allow combustible material such as dry grass or fuel to do so.

SAFETY RULES

WARNING: Failure to follow all

Safety Rules and Precautions can result in serious injury.

KNOW YOUR UNIT

SRead your instruction manual carefully until you completely understand and can follow

all warnings and safety rules before operat- ing the unit.

DRestrict unit to users who understand and will follow all warnings and safety rules in this manual.

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can rico- chet, be thrown, or otherwise cause injury or damage during operation.

Use your unit as a blower for:

D Sweeping debris or grass clippings from driveways, sidewalks, patios, etc.

DBlowing grass clippings, straw, or leaves into piles, around joints, or between bricks.

Use your unit as a vacuum for:

DPicking up dry material such as leaves, grass, small twigs, and bits of paper.

DFor best results during vacuum use, operate your unit at high speed.

DMove slowly back and forth over the mate- rial as you vacuum. Avoid forcing the unit into a pile of debris as this can clog the unit.

DKeep the vacuum tube about an inch above the ground for best results.

PLAN AHEAD

DAlways wear eye protection when operat- ing, servicing, or performing maintenance on unit. Wearing eye protection will help to prevent rocks or debris from being blown or ricocheting into eyes and face which can

result in blindness and/or serious injury. Eye protection should be marked Z87.

D Always wear foot protection. Do not go barefoot or wear sandals.

D Always wear respirator or face mask when

working with unit in dusty environments. D Secure hair so it is above shoulder length.

Keep loose hair, loose clothing, fingers, and all other parts of the body away from openings and moving parts. Hair, jewelry, loose cloth- ing, or clothing with loosely hanging straps, ties, tassels, etc., can be caught in moving parts.

DDo not operate unit when you are tired, ill, up- set, or if you are under the influence of alco- hol, drugs, or medication.

D Keep children, bystanders, and animals away from work area a minimum of 30 feet (10 meters) when starting or operating unit. Do not point the blower nozzle in the direc- tion of people or pets.

HANDLE FUEL WITH CAUTION, IT IS

HIGHLY FLAMMABLE

DEliminate all sources of sparks or flame (in- cluding smoking, open flames, or work that

can cause sparks) in the areas where fuel is mixed, poured, or stored.

DMix and pour fuel in an outdoor area; store fuel in a cool, dry, well ventilated place; use an approved, marked container for all fuel purposes.

D Do not smoke while handling fuel or while operating the unit.

D Make sure the unit is properly assembled and in good operating condition.

DDo not fill fuel tank while engine is hot or running.

DAvoid spilling fuel or oil. Wipe up fuel spills before starting engine.

-- 3 --

DMove at least 10 feet (3 meters) away from fuel and fueling site before starting engine.

D Always store gasoline in a container ap- proved for flammable liquids.

OPERATE YOUR UNIT SAFELY

WARNING: Stop the engine before

opening the vacuum inlet door. The engine must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.

D Inspect unit before each use for worn, loose, missing, or damaged parts. Do not use until unit is in proper working order.

D Keep outside surfaces free of oil and fuel.

DNever start or run engine inside a closed room, building or other unventilated area. Breathing exhaust fumes can kill.

DTo avoid static electricity discharge, do not wear rubber gloves or any other insulated

gloves while operating unit.

D Do not set unit on any surface except a clean, hard area while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through discharge opening, damaging unit, property, or causing serious injury to bystanders or operator.

DAvoid dangerous environments. Do not use in unventilated areas or where explosive vapors or carbon monoxide build up could

be present.

DDo not overreach or use from unstable sur- faces such as ladders, trees, steep slopes, rooftops, etc. Keep firm footing and balance

at all times.

D Never place objects inside the blower tubes; always direct the blowing debris

away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or cause other damage.

D Never run unit without the proper equip- ment attached. When using your unit as a blower, always install blower tubes. When

using your unit as a vacuum, always install vacuum tubes and vacuum bag assembly. Make sure vacuum bag assembly is com- pletely zipped.

D Check air intake opening, blower tubes, vacuum tubes, and elbow tube frequently, always with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow.

D Never place any object in the air intake open- ing as this could restrict proper air flow and cause damage to the unit.

D Never use for spreading chemicals, fertiliz-

ers, or other substances which may contain toxic materials.

DTo avoid spreading fire, do not use near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc.

D Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

WARNING: Disconnect spark plug be- fore performing maintenance except for carbu- retor adjustments.

DHave all maintenance other than the rec-

ommended procedures described in the in- struction manual performed by an autho- rized service dealer.

D Use only recommended Poulan PRO re-

placement parts; use of any other parts may void your warranty and cause damage

to your unit.

DEmpty fuel tank before storing the unit. Use up fuel left in carburetor by starting engine and

letting it run until it stops.

D Do not use any accessory or attachment

other than those recommended by manufac- turer for use with your unit.

DDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an

open flame from hot water heaters, electric motors or switches, furnaces, etc.

D Store in a dry area out of reach of children.

WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth de- fects or other reproductive harm.

SPECIAL NOTICE: Exposure to vibra- tions through prolonged use of gasoline pow- ered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood vessel dam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the require- ments of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Ore- gon, and Washington require by law that

many internal combustion engines be equipped with a spark arresting screen. If you

operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the MAINTENANCE section for information on maintenance of the muffler and spark arrest- ing screen.

-- 4 --

ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

WARNING: If you receive your unit

assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit.

DA standard screwdriver is required for as- sembly.

BLOWER TUBE ASSEMBLY

1.Align the rib on the upper blower tube with the groove in the blower outlet; slide the tube into place.

NOTE: Knob must be loose enough to allow blower tube to be inserted in blower outlet. Loos- en knob by turning counterclockwise.

Blower Outlet

6.To remove the tubes, turn the knob coun- terclockwise to loosen the tubes; remove the tubes.

HIGH-SPEED NOZZLE ASSEMBLY

When greater air speed is desired, use the high--speed nozzle.

1.Align the slots on the nozzle with the tabs on the lower blower tube.

High--Speed

Nozzle

Lower Blower Tab

TubeSlot

2.Slide the nozzle onto the lower blower tube.

3.Turn the nozzle clockwise until a click is felt to secure the nozzle to the lower blow- er tube.

VACUUM BAG ASSEMBLY

1.Open the zipper on the vacuum bag and insert the elbow tube.

2.Push the small end of the elbow tube through the small opening in the bag.

Elbow

TubeRib

Groove Rib

2.Secure the tube by turning the knob clock- wise.

3.Align the slots on the lower blower tube with the tabs on the upper blower tube.

Upper Blower

Tube

Lower Blower

Tube

Tab

Slot

4.Slide the lower blower tube onto the upper blower tube.

5.Turn the lower blower tube clockwise until a click is felt to secure the lower blower tube to the upper blower tube.

NOTE: When the upper and lower blower

tubes are assembled together properly, the arrows on both tubes will be aligned.

Zipper Opening

Small Opening

NOTE: Make sure edge of the small opening

is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom.

3.Close the zipper on the bag. Make sure the zipper is closed completely.

4.Remove blower tubes from engine.

Rib

Groove

5.Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove.

6.Turn knob clockwise to secure elbow tube.

VACUUM TUBE ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or

-- 5 --

blower tubes. The rotating blades can cause serious injury.

1.Insert the tip of a screwdriver into the latch area of the vacuum inlet.

Latch Area Blower

Outlet

Latch

Area

Vacuum Inlet Cover

2.Gently tilt the handle of the screwdriver to- ward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand.

3.Hold the vacuum inlet cover open until up- per vacuum tube is installed.

Vacuum

Inlet

Cover c

Vacuum Inlet

4.Align the tabs on the inside of the vacuum in- let with the slots on the upper vacuum tube.

Tab

Slot

5.Push the upper vacuum tube into the vac- uum inlet. Turn the tube counterclockwise until a click is felt to secure the tube to the blower unit.

6.Align slanted end of lower vacuum tube as shown. Firmly push lower vacuum tube into upper vacuum tube.

Slanted end of lower vacuum tube

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1.Remove the elbow tube and vacuum bag by turning the knob counterclockwise to loosen the elbow tube.

2.Remove the vacuum tubes by turning the tubes clockwise.

3.Close the vacuum inlet cover and make sure it is latched closed.

4.Reinstall the blower tubes (see BLOWER

TUBE ASSEMBLY).

SHOULDER STRAP ADJUSTMENT

1.Hold the unit as shown with the muffler side facing away from your body and clothes.

2.Pass the shoulder strap over your head and onto your right shoulder.

3.Extend your left arm toward the rear of the vacuum bag.

4.Adjust shoulder strap until the vacuum bag/shoulder strap seam lies between your thumb and index finger.

5.Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate properly.

-- 6 --

OPERATION

KNOW YOUR BLOWER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

High--Speed

Nozzle

STOP SWITCH

The STOP switch is used to stop the engine. To stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

THROTTLE TRIGGER

The THROTTLE TRIGGER is used to select the desired engine speed.

PRIMER BUTTON

The PRIMER BUTTON removes air from the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate primer button by pressing it and allowing it to return to its origi- nal position.

CHOKE LEVER

The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After engine attempts to start, move the choke lever to the HALF CHOKE position.

Once engine starts, move choke lever to the RUN position.

-- 7 --

S To reduce noise levels, operate power blowers at the lowest possible throttle speed to do the job.

S Use rakes and brooms to loosen debris be- fore blowing.

S In dusty conditions, slightly dampen sur- faces or use a mister attachment when wa-

ter is available.

S Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens.

SWatch out for children, pets, open windows, or freshly washed cars. Blow debris away

safely.

SUse the full blower nozzle extension so the air stream can work close to the ground.

SAfter using blowers and other equipment, CLEAN UP! Dispose of debris in trash re- ceptacles.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan PRO brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive

oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or

using ethanol or methanol) can cause major engine performance and durability problems.

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20%

alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor

components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HOW TO STOP YOUR ENGINE

D Release the throttle trigger.

S Push and hold the STOP switch in the STOP position until the engine stops.

HOW TO START YOUR ENGINE

WARNING: You MUST make sure the tubes are secure before using the unit.

DFuel engine. Move at least 10 feet (3 me- ters) away from the fueling site.

DHold the unit in the starting position as shown. Make sure the blower end is di- rected away from people, animals, glass, and solid objects.

STARTING POSITION

Blower

Vacuum

WARNING: When starting engine,

hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

HELPFUL TIP

If your engine still does not

start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

1.Slowly press the primer bulb 6 times.

2.Move choke lever to the FULL CHOKE posi- tion.

3.Squeeze the throttle trigger fully and hold through all remaining steps.

-- 8 --

Starter

Handle

Choke

Lever

Primer

Bulb

4.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

5.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

6.Pull starter rope sharply until engine runs, but no more than 6 pulls. NOTE: If the en- gine doesn???t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine still doesn???t start, it is probably flooded. Proceed to START-

ING A FLOODED ENGINE.

7.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the RUN position, move the choke lever to the HALF CHOKE posi- tion and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze the throttle trigger fully and hold through all remaining steps.

3.Pull starter rope sharply until engine runs, but no more than 6 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter

rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn???t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

MAINTENANCE

WARNING: Avoid touching muffler

unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure

the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac-

cessing movable parts.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec- ommended maintenance described in the instruction manual performed by an

authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your re- sponsibility to maintain and perform general maintenance.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

S Muffler

S Spark Plug Boot

S Air Filter

S Housing Screws

CHECK FOR DAMAGED OR WORN

PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

INSPECT AND CLEAN UNIT AND

DECALS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild deter- gent.

S Wipe off unit with a clean dry cloth.

-- 9 --

CLEAN AIR FILTER

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean or replace air filter after every 5 hours of operation or yearly, whichever comes first.

Button

Air Filter

Cover

Air Filter

Cleaning the air filter:

1.Clean the cover and the area around it to keep debris from falling into the carburetor chamber when the cover is removed.

NOTE: Move choke lever to RUN position before opening air filter cover.

2.Open air filter cover by pushing button (see illustration). Remove air filter.

NOTE: Do not clean filter in gasoline or other flammable solvent. Doing so can create a fire

hazard or produce harmful evaporative emis- sions.

3.Wash the filter in soap and water.

4.Allow filter to dry.

5.Apply a few drops of oil to the filter; squeeze filter to distribute oil.

6.Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Igni- tion timing is fixed, nonadjustable.

NOTE: This spark ignition system complies with the Canadian standard ICES--002.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and dis- card.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4.Reinstall the spark plug boot.

REPLACE FUEL FILTER

To replace fuel filter, drain unit by running it dry of fuel, then remove fuel cap/retainer assem- bly from tank. Pull filter from tank and remove

it from the fuel line. Install new fuel filter on fuel line; reinstall parts.

Fuel Filter

Fuel Line

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting screws are tightened securely to prevent damage.

Muffler

Mounting

Screw

MUFFLER AND SPARK ARREST-

ING SCREEN

WARNING: The muffler on this prod-

uct contains chemicals known to the State of California to cause cancer.

NOTE: THE SPARK ARRESTING SCREEN

ON THIS UNIT IS NOT SERVICEABLE.

For normal homeowner use, the muffler and spark arresting screen will not require replace- ment. After 50 hours of use, we recommend that your muffler be replaced by your authorized

service dealer.

CARBURETOR IDLE SPEED

ADJUSTMENT

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed Screw

Air

Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

-- 10 --

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy stor-

age.

S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run

engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly

to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

S Clean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

S Replace your gasoline can if it starts to rust.

-- 11 --

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing any of the recommended remedies below other than remedies that require operation of the unit.

-- 12 --

LIMITED WARRANTY

Poulan PRO, a division of Husqvarna Consum- er Outdoor Products N.A., Inc., warrants to the original consumer purchaser that each new Poulan PRO brand gasoline tool or attachment is free from defects in material and workman- ship and agrees to repair or replace under this warranty any defective gasoline product or at-

tachment as follows from the original date of purchase.

2 YEARS - Parts and Labor, when used for household purposes.

90 DAYS - Parts and Labor, when used for commercial, professional, or income producing purposes.

30 DAYS - Parts and Labor, if used for rental purposes.

This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance or alteration,

or the use of accessories and/or attachments not specifically recommended by Poulan PRO for this tool. This warranty does not cov- er tune--up, spark plugs, filters, starter ropes, or blower and vacuum tubes that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre--delivery setup or normal adjustments explained in the instruction manual. This warranty does not cover trans-

portation costs.

In the event you have a claim under this warran- ty, you must return the product to an authorized service dealer.

Should you have any unanswered questions concerning this warranty, please contact:

Poulan PRO, a division of Husqvarna

Consumer Outdoor Products N.A., Inc. 7349 Statesville Road

Charlotte, NC 28269 1--800--554--6723

In Canada, contact:

Poulan PRO

850 Matheson Blvd. West Mississauga, Ontario L5V 0B4

Giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE OTH-

ER RIGHTS WHICH VARY FROM STATE TO

STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE LIM-

ITATIONS OR EXCLUSION MAY NOT APPLY

TO YOU.

This is a limited warranty within the meaning of that term as defined in the Magnuson--Moss Act of 1975.

The policy of Poulan PRO is to continuously improve its products. Therefore, Poulan

PRO reserves the right to change, modify, or discontinue models, designs, specifications,

and accessories of all products at any time without notice or obligation to any purchaser.

U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OB- LIGATIONS: The U.S. Environmental Protection Agency, California Air Resources Board, Environment Canada and Poulan PRO are pleased to explain the emissions con- trol system warranty on your year 2010 and lat- er small off--road engine. In California, all small off--road engines must be designed, built, and equipped to meet the State???s stringent anti--

smog standards. Poulan PRO must warrant the emission control system on your small off--road engine for the periods of time listed

below provided there has been no abuse, ne- glect, or improper maintenance of your small

off--road engine. Your emission control system includes parts such as the carburetor, the igni- tion system and the fuel tank. Where a warrant-

able condition exists, Poulan PRO will repair your small off--road engine at no cost to you. Expenses covered under warranty include

diagnosis, parts and labor.

MANUFACTURER???S WARRANTY COV-

ERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by

Poulan PRO. OWNER???S WARRANTY RE- SPONSIBILITIES: As the small off--road en-

gine owner, you are responsible for the per- formance of the required maintenance listed in your instruction manual. Poulan PRO rec-

ommends that you retain all receipts covering maintenance on your small off--road engine,

but Poulan PRO cannot deny warranty solely for the lack of receipts or for your failure to en- sure the performance of all scheduled main-

tenance. As the small off--road engine owner, you should be aware that Poulan PRO may deny you warranty coverage if your small off--

road engine or a part of it has failed due to

-- 13 --

abuse, neglect, improper maintenance, un- approved modifications, or the use of parts not made or approved by the original equip- ment manufacturer. You are responsible for presenting your small off--road engine to an Poulan PRO authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsi- bilities, you should contact your nearest autho- rized service center, call Poulan PRO at 1--800--554--6723, or send e-mail correspon- dence to emission.warranty@HCOP-- emission.com. WARRANTY COMMENCE-

MENT DATE: The warranty period begins on the date the small off--road engine is pur- chased. LENGTH OF COVERAGE: This

warranty shall be for a period of two years from the initial date of purchase, or until the end of the product warranty (whichever is lon-

ger). WHAT IS COVERED: REPAIR OR RE- PLACEMENT OF PARTS. Repair or replace- ment of any warranted part will be performed at no charge to the owner at an approved

Poulan PRO servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your near-

est authorized service center, call Poulan PRO at 1--800--554--6723, or send e-mail corre- spondence to emission.warranty@HCOP--

emission.com. WARRANTY PERIOD: Any warranted part which is not scheduled for re- placement as required maintenance, or which

is scheduled only for regular inspection to the effect of ???repair or replace as necessary??? shall be warranted for 2 years. Any warranted part which is scheduled for replacement as re- quired maintenance shall be warranted for the period of time up to the first scheduled re- placement point for that part. DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to the determination that a

warranted part is defective if the diagnostic work is performed at an approved Poulan PRO servicing center. CONSEQUENTIAL

DAMAGES: Poulan PRO may be liable for damages to other engine components caused by the failure of a warranted part still under warranty. WHAT IS NOT COVERED: All failures caused by abuse, neglect, or im- proper maintenance are not covered. ADD- ON OR MODIFIED PARTS: The use of add-- on or modified parts can be grounds for disal- lowing a warranty claim. Poulan PRO is not li- able to cover failures of warranted parts caused by the use of add--on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Pou- lan PRO at 1--800--554--6723, or send e-mail correspondence to emission.warranty@

HCOP--emission.com. WHERE TO GET WARRANTY SERVICE: Warranty services or repairs shall be provided at all Poulan PRO service centers. Call: 1--800--554--6723 or send e-mail correspondence to emission. warranty@HCOP--emission.com. MAINTE-

NANCE, REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS: Any Pou- lan PRO approved replacement part used in

the performance of any warranty mainte- nance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CON-

TROL WARRANTY PARTS LIST: Carbure-

tor, air filter (covered up to maintenance sched- ule), ignition system: spark plug (covered up to maintenance schedule), ignition module, muffler including catalyst (if equipped), fuel tank.

MAINTENANCE STATEMENT: The owner is responsible for the performance of all re- quired maintenance as defined in the instruc- tion manual.

The information on the product label indicates which standard your engine is certified. Example: (Year) EPA and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use: Moderate (50 hours)

Intermediate (125 hours) Extended (300 hours)

-- 14 --