WELCOME

This user guide provides instructions on the setup and usage of the Plantronics Pulsar??? 260 Bluetooth?? Headset. Before getting started, please review the safety booklet included in your package.

For additional help, service or support information, refer to product warranty card or Troubleshooting on page 9, or visit www.plantronics.com.

TABLE OF CONTENTS

Register your product online

Visit www.plantronics.com/productregistration to register your product online so that we can provide you with the best possible service and technical support.

PACKAGE CONTENTS & FEATURES

Pulsar 260 headset

Microphone with call control button

Sound-isolating earbuds

2.5mm plug

Stereo Bluetooth pod

Mini-USB port

Indicator light

Power on/off/pairing

2.5mm port

Detachable clip

CHARGING

You must charge for 3 hours before ???rst use.

To charge, connect AC charger to pod mini- USB socket.

Pod indicator light ???ashes red when charging and changes to solid blue when fully charged.

POWERING ON/OFF

Press and hold power on/off switch for >2 seconds.

PAIRING

To pair pod with phone:

Begin with pod powered on.

1.Press and hold both the mute/play/ pause button and the power on/off/ pairing button simultaneously. When the indicator light ???ashes red and blue, release buttons.

2.While pod is ???ashing red and blue, use the phone menu to search for Bluetooth devices and select ???260 Plantronics???.

3.When prompted for password, enter

0000.

Pod ???ashes blue when paired successfully.

For set up and pairing instructions with Bluetooth devices other than mobile phones, please consult your Bluetooth device user guide.

1

2

password

0000

POD INDICATOR LIGHTS

NOTE: Flashes red when headset is initially powered on.

MAKING/ANSWERING/ENDING CALLS

To make a call:

Dial on phone; call transfers automatically to headset.

To answer or end a call:

Brie???y press call control button on headset.

To adjust volume:

Short press + or ??? buttons on pod for incremental change, hold for continuous change.

WEARING OPTIONS

Pulsar 260 can be worn in two ways:

??? Clipped to your belt or clothing

??? Around your neck using the lanyard

POD CONTROLS

Power on/off

POWERED SPEAKER & STEREO USES

For public listening you can connect the stereo Bluetooth pod directly to powered speakers or your home stereo with the included audio-out cable (provided your speakers/home stereo is ???tted with a Line-in or Auxiliary 3.5mm audio socket). Please consult your equipment guide.

Tone

No tone

High tone

Repeating low tone every 60 seconds

High tone

Mid tone for each adjustment, double low tone at limit

1. Ensure the stereo Bluetooth pod and your speakers/home stereo are powered off.

2. Connect the audio-out cable 2.5mm plug to the stereo Bluetooth pod and the 3.5mm plug to the powered speakers/home stereo Line-in or Auxiliary 3.5mm audio socket as shown below.

3.Power on both the stereo Bluetooth pod and your speakers/home stereo.

*Only works if Bluetooth device supports Bluetooth Audio/Video Remote Control Profile (AVRCP).

HEADSET CONTROLS

TROUBLESHOOTING

Problem

My headset does not work with my phone.

Callers cannot hear me.

Callers say my voice is too quiet.

I cannot hear caller/dial tone or audio sound.

I cannot hear music from my powered speakers/Hi-Fi when using the audio-out cable.

Solution

???See page 5 ???Pairing???.

???Perform a reset on Pulsar 260 as described below.

???Headset is muted. Press the mute button on the pod to unmute the microphone.

???Ensure pod is powered on and headset is paired with audio device. See page 5 ???Pairing???.

Ensure that microphone is pointing towards your mouth.

???Pod is turned off. Check the indicator light for status.

???Headset is out of range. Walk to within 10 metres of the phone and check the Bluetooth link on your phone???s display.

???Battery is dead. Charge your battery using the AC power adapter supplied.

???Listening volume is too low. Press the volume/mute button to increase the sound heard in the headset.

???Pod must be turned on and connected to the powered speakers/Hi-Fi with the audio-out cable.

???Check music player on Bluetooth phone is switched on and Pulsar 260 is the active Bluetooth device.

Hands-free features

Features must be supported by Bluetooth device or service provider.

SYSTEM RESET

To reset:

1. Remove clip as shown at right.

2. Press and release button using a pen.

2

PRODUCT SPECIFICATIONS

Supports Bluetooth hands-free and headset profiles, Advanced Audio Distribution Profile (A2 DP), Audio/Video Remote Control Profile (AVRCP) and Generic Audio/ Video Distribution Profile (GAVDP). For stereo sound, Bluetooth-enabled devices must support the Advanced Audio Distribution Profile (A2DP).

* Performance may vary by device.

TECHNICAL ASSISTANCE

Visit our web site at www.plantronics.com/support for technical support including frequently asked questions, compatibility and accessibility information.

The Plantronics Technical Assistance Centre (TAC) is also ready to assist you on

0800 410014 from the UK.

EXPOSURE TO RF RADIATION

The internal wireless radio operates within the guidelines found in radio frequency safety standards and recommendations, which re???ect the consensus of the scienti???c community. Independent studies have shown that the internal wireless radio is safe for use by consumers. Visit www.plantronics.com for more information.

NOTE: Modi???cations not expressly approved by Plantronics, Inc. could void the user???s authority to operate the equipment.

MODEL AND COUNTRY INFORMATION

37677-04

GBR

37677-05

AUT, BEL, DEU, DNK, ESP,

FRA, GRC, ITA, IRL, LUX,

NLD, PRT, SWE, FIN, CYP,

CZE, EST, HUN, LVA, LTU, MLT, POL, SVK, SVN.