PH750T

Owner???s Manual

Introduction

Congratulations on your purchase of a Philips Universal Remote Control. Philips Universal Remotes let you replace a broken or lost remote or combine more than one remote into one. In addition, this remote is equipped with a command learning feature which lets the remote learn commands from your original equipment remote control!

This remote control operates the common features of most but not all models and brands of IR Infrared Controlled Video Equipment. This remote may provide functions that are not available on your equipment. Some functions of your particular equipment (e.g. menu functions) may not be controlled by this remote. In such cases, use the original remote control for your equipment. Please use this manual to become familiar with your Philips Universal Remote. After you are familiar with your remote the first thing you need to do is to install batteries and setup your remote for your particular product and brand.

The remote also transmits wireless Radio Fre- quency (RF) commands to the video sender. The video sender receives these commands and converts them to regular Infrared (IR) commands. These IR commands are then emitted from an IR Extender cable to control your A/V components. This lets you control your A/V components from ANY room in your home - you don???t need to aim the remote at your component!

Thank you for buying a Philips remote and we hope it will give you many years of service.

Button Functions, cont.

DVD Functions (labeled in Blue)

SCAN+ and SCAN- buttons control the speed of Fast Forward and Reverse Playback respectively. CHAPTER+ and CHAPTER- buttons respectively locate the succeeding or preceding Chapters or Tracks on a disc.

REPEATA-B button performs DVD players ???A-B Repeat??? (or RPT A.B) function for repeat play of current Chapter or Track.

INFO/SELECT button brings up DVD Display or Control Menu for Chapter/Track/Title number, Time remaining/elapsed indication, system information, etc. MENU brings up the DVD disc Menu screen - use with the UP, DOWN, LEFT & RIGHT navigation buttons. OK button is used for on-screen Menu selection. Note some DVD players require the Play button to be used. SUBTITLE ON-OFF (CC) Turns the subtitles on or off. QUIT Exit On-Screen Menus and/or Return to previous On-Screen selection.

Note, not all DVD Players support all the functions described above.

SAT Functions

GUIDE button displays on-screen Satellite Channel Guide.

CHAPTER+ and CHAPTER- buttons perform the ???Page+??? and ???Page-??? function for on-screen Guide Menus used by some Satellite systems.

INFO/SELECT button brings up Satellite Display screen for current Channel and system information.

MENU brings up the Satellite Menu screen - use with the UP, DOWN, LEFT & RIGHT navigation buttons.

OK button is used for on-screen Menu selection. QUIT button is used to Exit or Clear on-screen Menu displays.

6

Setup

Battery Installation

1. On the back of the remote, push down on the tab and lift the cover off.

2.Match the batteries to the + and - marks inside the

battery case, then insert 2 AAAAlkaline batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).

Code Saver

Codes are stored in permanent memory while you are changing batteries so you will not lose any codes stored in the remote while you are changing batteries.

Power-On Default

The remote powers on in TV mode.

Code Setup

The CODE SEARCH button is used to setup the remote. You can either setup the remote using the code for your brand of product, from the code tables (on separate sheet), or you can search through the library of codes until you find a code that works for your product.

Please refer to ???Programming with Code Search??? on page 8 for more information on using the code search feature to learn how to search through the library of codes for your products.

NOTE: You can store any kind of code under any mode (except TV). I.E. you can store a VCR code under the CBL button, or a DVD code under the VCR button, etc. However, you can only store TV codes under the TV button.

7

1.Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button.

2.Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.

3.Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.

4.With your device on, press CHANNELUP. If the device responds, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand.

Write your codes down here for easy reference later.

Code Search

If your product does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps.

1.Manually turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

5.Press and release MUTE to install the code.

8

Most users will store VCR codes under the VCR button, Cable codes under CABLE, etc. If (for example) you want to store a VCR code under CABLE, first follow the procedure for Direct Code Entry (previous page) and press CABLE in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search (or Brand Search, below). Note: If the device does not have a CHANNELUP button, use PLAY (VCR only) or POWER instead. Code Search starts from the currently stored 4 digit number under that mode.

Code Search by Brand

Lets you search for a code for a specific Brand within the Code Library for a particular manufacturer.

1.Turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the CODE SEARCH button until the red indicator remains on, then release CODE SEARCH button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press and release the numeric button (0-9) corresponding to desired Manufacturer (see table on code list sheet). The red indicator blinks off once. Note, pressing ???0??? performs a full library search same as normal Code Search Method on previous page.

5.Press the CHANNEL UP button ((or POWER or PLAY (VCR only)) repeatedly until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

6.Press and release MUTE to install the code.

Brand Search Method entry is now complete.

Note: When all codes under a Brand have been searched the red indicator flashes rapidly for 3 seconds.

9

Code Identification Feature

The Code Identification Feature allows you to identify the 4 digit library code stored under your device key. For example, if you want to find out what 4 digit code is stored under your TV device key, follow the six steps below:

1.Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button.

2.Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.

3.Press and release the CODE SEARCH button. The red indicator blinks off.

4.To find the first digit for the code stored under the mode key pressed in step 2, press each numeric key from 0-9 in turn. When the red indicator blinks off the number you pressed is the first digit for the code you are searching for.

5.To find the second digit, repeat step 4, this time when the red indicator blinks off this is the second digit.

6.Repeat step 4 to find the third and fourth digits.

Sleep Timer

The SLEEP button operates the Sleep function of your device providing it supports the Sleep function. Alternatively, you can enable the remote to turn off your TV after a period of 1 to 99 minutes as shown below. This feature is only available for the TV Mode and the remote must be in TV Mode to set a Sleep Timer. This feature works even if your TV does not have its own Sleep function.

1.Press and release the TV Mode button.

2.Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button.

3.Press and release the SLEEP button (Note any previously set Sleep timer is cancelled at this point and the remote returns to normal operation).

4.Press and release the numeric buttons (01-99) for the time required. The red indicator blinks off to indicate button press acceptance and remains off after the second button press.

5.TV Sleep Timer now set.

6.Leave the Remote pointing towards the TV with an unobstructed path.

To cancel the Sleep Timer, press and release the POWER button in TV Mode or repeat Steps 1, 2 and 3 above.

10

Setup, cont.

Programming Combo Device Codes

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/ VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/DVD Combo, you might need to set up one code under the TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/ VCR, etc.) have separate buttons on the original remote to select the part of the Combo device to be controlled. For example, if your Combo device is a DVD/VCR then its original remote might have separate DVD and VCR buttons for selection of the Combo part you would control. The equivalent button functions can be found on your Philips remote by using the device Mode and

CODE SEARCH buttons.

Referring to ???Programming with Code Search??? on page 8, setup a device Mode (e.g. DVD) with the correct code for your Combo device. Assuming the DVD/VCR Combo device is the example and its code is programmed under DVD Mode, press and hold the DVD Mode button for more than one second to send the DVD button command. To send the VCR button command, quickly press and release the CODE SEARCH button followed by pressing and releasing the DVD Mode button. This method can be applied similarly to all Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) and is available for all Modes. Note this feature is not supported by all codes.

Controlling Devices Requiring Separate Power On and

Off Buttons

Some devices (e.g. certain RCA TVs) require separate Power On and Power Off buttons to turn the device on and off. The equivalent button functions can be found on your Philips remote by using the device Mode and POWER buttons. Referring to ???Programming with Code Search??? on page 8, setup a device Mode (e.g. TV) with the correct code for your device.

Assuming a TV device is the example and its code is programmed under TV Mode, to turn your TV on, press and hold the TV Mode button for more than one second to transmit the Power On button command.

11

Setup, cont.

Controlling Devices Requiring Separate Power On and Off Buttons, cont.

To turn the TV off, press and release the POWER button to transmit the Power Off button command. This method can be applied similarly to any device and is available for all Modes. Note this feature is not supported by all codes.

VCR/DVD/DVR Punch-Through Feature

This remote allows the 6 VCR transport buttons (i.e.

PLAY, PAUSE, STOP, FF, REWIND, and REC) to Punch-Through control from any Mode programmed with TV, SAT or Cable codes to the last VCR, DVD or DVR programmed Mode you used. Normally other types of remotes only punch-through (from another Mode) on the 6 VCR buttons to the device programmed under the VCR Mode button. This is not much use if you are using a DVD programmed under a Mode other than VCR. For example, if you have 2 DVD, VCR or DVR devices programmed into this remote, the last one you accessed on the remote will be the one that has control of the 6 VCR transport buttons when in any other Mode. This feature will not operate if the programmed TV, SAT or Cable code has its own VCR transport button control e.g. a TV Combo, SAT/PVR, etc.

Volume/Mute Control and Punch-Through Feature

This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set (factory default) for all device Modes programmed with ???Visual??? codes (e.g. TV, VCR, DVD, DVR, SAT & CABLE) and ???Audio??? codes (e.g. CD & AUDIO) to use their own Volume/Mute control if present. If the programmed ???Visual??? code has no Volume/Mute operation of its own then those buttons will punch- through control to the TV Mode device without needing to change to TV Mode. Please refer to the next page for more information.

Setup, cont.

Any Mode chosen forVolume/Mute control MUST have its own Volume/Mute function or the Volume/Mute buttons will do nothing.

SettingALLVolume/Mute Control to any one Mode

This routine can set all Modes to ???punch-through??? to any one chosen Mode for Volume/Mute button control without the needing to change to that Mode.

1.Press and hold the CODE SEARCH button until the red indicator turns on, then release the button.

2.Press and hold the MUTE button until the red indicator blinks off, then release the button.

3.Press and release the desired Mode button (TV, VCR, etc.) for Volume/Mute control, the red indicator blinks then stays on.

4.Press and release the MUTE button and the red indicator turns off. The red indicator will blink rapidly for three seconds if the Mode you have selected has no Volume/Mute control.

5.All other Modes will now punch-through to your chosen Mode for Volume/Mute control.

6.All ???Visual??? and ???Audio??? programmed Modes will now punch-through to the respective Modes you have chosen for Volume/Mute control.

Setting any Mode to use its own Volume/Mute Control

This routine can set any Mode to use only its own Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/ Mute buttons will do nothing.

1.Press and hold the CODE SEARCH button until the red indicator turns on, then release the button.

2.Press and hold the MUTE button until the red indicator blinks off, then release the button.

3.Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on.

4.Press and release the VOLUME- (Down) button, the red indicator blinks then stays on.

5.Press and release the MUTE button and the red indicator turns off.

6.All ???Visual??? and ???Audio??? programmed Modes will now punch-through to the respective Modes you have chosen for Volume/Mute control.

Code Learning

The learning feature lets you ???learn??? functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an ???easy learning??? feature that lets you ???learn??? features (such as RANDOM PLAY from your original CD remote).

Tips On Learning

You can only learn one device type under any one Mode button e.g. only learn TV codes under the TV Mode, VCR codes under the VCR Mode, etc. If you are trying to learn from a ???Universal??? remote, it might have more than one code type stored under a Mode. Try learning from another remote to see if there???s a problem with the type or brand of remote you are trying to learn from.

a.Some functions from some types of remotes might not be able to be learned.

b.No functions may be stored under LEARN, or CODESEARCHbuttons.

c.Only one original device type can be learned per individualMode.

d.Use fresh batteries for both the Learning Remote and the Original Remote.

e.Keep at least three feet away from incandescent or low-energy lights when learning.

f.Perform a Master Clear (see page 18) before learning and try learning 2 or 3 commands initially. Then carry out a Master Clear before completely learning your original remote???s commands.

g.Place the original remote end-to-end with the Learning Remote so the IR transmitters on both remotes are directly in line with each other. You may need to adjust the height of either remote to achieve this. Use the IR Transmitter Finder feature to assist you.

h.Keep the distance between the two remotes to approximately 1 inch and do not move or change the distance between the two remotes until you have learned all the required buttons for that Mode.

i.When Learning, do not release the button being Learned until the red indicator has blinked off for half a second.

j.Avoid learning your original remote Volume/Mute buttons unless you are sure these operate the same device e.g. some original DVD remotes include TV Volume/Mute button control and can be two different types of code.

14

Tips On Learning, cont.

k.Avoid learning your original remote VCR transport buttons unless you are sure these operate the same device e.g. some original TV remotes include VCR button control and can be two different types of code.

l.If learning the first or second buttons for a Mode results in continuous errors then try the following:

i.End the Learn session by pressing the CODE SEARCHkey.

ii.Clear out the learned commands for that Mode.

iii.Check the IR transmitters are correctly aligned between the two remotes (use the IR Transmitter Finder facility).

iv.Adjust the distance between the two remotes to be closer (e.g. half an inch) or a further away (e.g. 2 inches) from each other.

v.Try learning the original remote for that Mode again.

If problems reoccur with the same button check the original remote button being learned ??? does it transmit? Does it operate the target device? Try learning that button under a different clear Mode. If it learns okay then it is likely to be a different code type from the others and cannot be learned under the same Mode.

15

This feature assists you in identifying where your original remotes IR transmitter is located and is particularly useful if your original remote???s IR transmitter is hidden behind a lens.

1.Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages)

2.Press and hold the CODE SEARCH button until the red indicator turns on, then release the button.

3.Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on.

4.Press and release the LEARN button, the red indicator blinks then stays on.

5.Press and hold any Original Remote button and move the Original Remote to the left and right, and/ or, up and down in front of the Learning remote IR transmitter. The red indicator will remain on if no IR from the Original remote is found and the red indicator will blink on and off more rapidly when the IR transmitters are lining up. The point where the red indicator blinks most rapidly is where the two IR transmitters are aligned. Note some original remotes will only transmit IR on the initial button press then stop. In these cases, quickly press and release the original remote button repeatedly during this procedure.

6.You can now learn a button from your original remote by continuing from ???Step 4??? in the ???Learning Commands??? section on the next page, or, to exit at this point, press and release the CODE SEARCH button

The learning feature allows you to ???learn??? functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an ???easy learning??? feature that allows you to ???learn??? features (such as RANDOM PLAY from your original CD remote) by following the steps below, and on the next page:

1.Press and hold the CODE SEARCH button until the red indicator turns on, then release the button.

2.Press and release the desired mode button (TV, VCR, etc.), the red indicator blinks then stays on.

3.Press and release the LEARN button, the red indicator blinks then stays on.

4.Press and release the Learning Remote button that you want to teach (e.g. POWER).

5.Point both remotes facing each other by approxi- mately 1 inch apart (see tips on page 14).

6.Press and hold the Original Remote button (e.g. Power) until the red indicator blinks once and stays on. If there is a learning problem, the indicator blinks for three seconds and stays on. If this happens, repeat Steps 4 to 6.

7.Repeat Steps 4-6 for other buttons you want to learn.

8.Press and release the CODE SEARCH button when all desired remote commands are learned. Code Learning is now complete.

6.

Line up your remotes (that you???re learning from) in front of the Learning remote, on a hard surface approx. 1 inch apart.

Clearing Commands

To Clearall Learned Commands undera mode

Clearing learned commands is helpful if, for example, you replace your CD player with another brand or model. If you had learned a feature from your old CD player???s original remote on to this remote (such as RANDOM PLAY), that feature would no longer work for your new CD player. Should you wish to remove or clear one or more ???learned??? commands, follow the steps below:

1.Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button.

2.Press and release the button for the mode you want to clear (TV, VCR, etc.). The red indicator blinks off.

3.Press and release the LEARN button TWICE. The red indicator blinks off.

4.Press and release the CODE SEARCH button. The red indicator turns off. All learned Commands under that mode are now cleared.

Master Clear - To Clear all Learned Commands under all modes

1.Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button.

2.Press and release the LEARN button TWICE. The red indicator blinks off.

3.Press and release the CODE SEARCH button. The red indicator turns off. All Learned commands in the remote are now cleared.

TV/VCR/INPUT

When in TV mode the TV/VCR/INPUT button performs the INPUT source switch function.

When in a mode that has been programmed for VCR the TV/VCR/INPUT button performs the TV/VCR antenna switch function.

When in a mode that has been programmed for Cable the TV/VCR/INPUT button performs theA.B switch function.

When in a mode that has been programmed for SAT the TV/VCR/INPUT button performs the TV/SAT switch function.

When in a mode that has been programmed for DVD the TV/VCR/INPUT button performs the DVD Setup function.

18

IR Extender Feature

The IR extender feature lets you use your remote control to control the A/V product that the Audio/ Video Sender is connected to. E.G., if the Audio/ Video Sender is connected to a DVD Player, or VCR in your living room, and the Audio/Video Receiver is connected to a TV in your bedroom; you can control the DVD Player or VCR while watching the picture from it on the TV in your bedroom. The remote sends Radio Frequency (RF) commands to the Audio/Video Sender (the unit with the thin antenna on it). It receives the RF commands from your remote and converts them to Infrared (IR) commands. You plug the IR extender cable into the jack on the back of the Audio/Video Sender and attach the IR emitters to the front of the DVD Player, or VCR, etc. that you want to control.

1.Plug the IR extender jack on the IR emitter cord into the IR EXT. socket located on the back of the Audio/Video Sender.

2.Place the emitter cord in front of the two devices you want to control (e.g., DVD and VCR).

3.Make sure that the two IR emitters are attached close to the IR sensors on the devices you want to control.

The IR emitter cord lets you control up to two IR devices.

19

Troubleshooting

Remote does not operate your product.

???Press the mode button of the product you want to control.

???Program the remote with a new code.

???Install new batteries. (You might have to reprogram your remote after installing new batteries.)

???Remote may not be compatible with your product.

Remote does not operate some features of your product.

???Program remote with a new code.

???Remote may not be able to operate all features of your product or button names might be different than your product.

Red Indicator blinks after you program a product code.

???Remote did not accept the code.

???Try to program the code again or try a different code.

For help with setup, please call: 919-573-7854.

Limited Lifetime Warranty

The manufacturer warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specifications and warnings, for as long as you own this product. This warranty extends only to the original purchaser of the product, and is nontransferable. Defective products, together with the dated proof of purchase, must be returned to the place of purchase for repair or replacement. THEREARE NO OTHER EXPRESS WARRANTIES. Incidental and consequential damages are disclaimed where permitted by law. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Made in China. Quality Assured in USA.

Ledgewood, NJ 07852

FCC Caution

THIS DEVICE COMPLIESWITH PART15 OF THE FCC

RULES. OPERATION IS SUBJECTTOTHE FOLLOW-

ING TWO CONDITIONS: (1)THIS DEVICE MAYNOT

CAUSE HARMFULINTERFERENCE,AND (2)THIS

DEVICEMUSTACCEPTANYINTERFERENCERE-

CEIVED,INCLUDINGINTERFERENCETHATMAY

CAUSEUNDESIREDOPERATION.

This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures.

???Reorient the antenna of the radio/TV experiencing the interference.

???Relocate the receiver with respect to the radio/TV.

???Move the receiver away from the radio/TV.

???Plug the receiver into an outlet on a different electrical circuit from the radio/TV experiencing the interference.

???If necessary, consult your local Dealer for additional suggestions.

NOTE: Modifications to any of the components in this kit will void the user???s authority to operate this equipment.

Introducci??n

Felicitaciones por su compra del Control remoto universal Philips. Los controles Philips le permiten sustituir un control remoto descompuesto o perdido, o combinar m??s de un control remoto en una sola unidad. Adem??s, ??este control remoto est?? equipado con una funci??n de transferencia de comandos que le permite transferir los comandos de su equipo de control remoto original!

Este control remoto opera las funciones comunes de la mayor??a de los modelos y marcas de equipo de video de control por rayos infrarrojos (pero no de todos). Este control remoto puede ofrecer funciones que no est??n disponibles en su equipo. Es posible que algunas funciones de su equipo en particular (por ej., men?? de funciones) no se puedan controlar con este control remoto. En tal caso, utilice el control remoto original de su equipo. Por favor, use este manual para familiarizarse con su control remoto universal Philips. Despu??s de familiarizarse con ??l, la primera cosa que tiene que hacer es colocar las bater??as y preparar su control remoto para su aparato y marca en particular.

El control remoto tambi??n transmite comandos de radiofrecuencia (RF) inal??mbrica al transmisor de video. El transmisor de video recibe estos comandos y los convierte en comandos infrarrojos (IR) comunes. Despu??s estos comandos IR se emiten desde un cable extendedor IR para controlar sus componentes A/V. Esto le permite controlar sus componentes A/V desde CUALQUIER habitaci??n de su hogar. ??No es necesario apuntar con el control remoto hacia el componente!

Gracias por comprar un control remoto Philips y esperamos que le brinde muchos a??os de servicio.

Funciones de botones

Funciones de DVD (con leyendas en azul)

Los botones SCAN+ y SCAN- controlan la velocidad para adelantar o retroceder la reproducci??n respectivamente. Los botones CHAPTER+ y CHAPTER- localizan respectivamente los cap??tulos o pistas siguientes o precedentes de un disco.

El bot??n REPEAT hace las funciones ???A-B REPEAT??? (o RPT A.B) de los reproductores de DVD para repetir la reproducci??n del cap??tulo o pista actual.

El bot??n INFO/SELECT trae la pantalla o el Men?? de control del DVD para indicar el n??mero de Cap??tulo/Pista/ T??tulo, el tiempo restante/transcurrido, informaci??n del sistema, etc.

MENU Trae la pantalla del Men?? de discos del DVD: ??selo con los botones de navegaci??n hacia arriba, abajo, izquierda y derecha.

OK (Aceptar) Se utiliza para la selecci??n del Men?? en pantalla.

SUBTITLE (CC) [Transcripici??n en pantalla, subt??tulos] Activa y desactiva la funci??n de transcripci??n del audio en pantalla o los subt??tulos de DVD.

Funciones de Sat??lite

El bot??n ???Guide??? presenta en pantalla la gu??a del canal v??a sat??lite.

Los botones ???Chapter+??? y ???Chapter-??? realizan la funci??n de ???Page+??? y ???Page-??? para los men??s de gu??a en pantalla utilizados en algunos sistemas de sat??lite.

El bot??n ???Info/Select??? trae la pantalla v??a sat??lite que indica la informaci??n actual del canal y del sistema.

Menu trae la pantalla del men?? v??a sat??lite. ??selo con los botones de navegaci??n hacia arriba, abajo, izquierda y derecha.

El bot??n OK se utiliza para la selecci??n del Men?? en pantalla.

El bot??n Quit se utiliza para salir o despejar las pantallas del men??.

TV/Videocasetera/Entrada

Cuando est?? en la modalidad de TV, el bot??n TV/VCR/ INPUT realiza la funci??n de cambio de fuente de

ENTRADA.

Cuando est?? en una modalidad que se ha programado para la videocasetera (VCR), el bot??n TV/VCR/INPUT realiza la funci??n de cambio de antena de TV/VCR.

Cuando est?? en una modalidad que se ha programado para Cable, el bot??n TV/VCR/INPUT realiza la funci??n de cambio A.B.

Cuando est?? en una modalidad que se ha programado para SAT, el bot??n TV/VCR/INPUT realiza la funci??n de cambio de TV / SAT.

Cuando est?? en una modalidad que se ha programado para DVD, el bot??n TV/VCR/INPUT realiza la funci??n de ajuste inicial de DVD.

26

Preparaci??n

Instalaci??n de bater??as

1. En la parte posterior de su control remoto empuje hacia abajo la leng??eta y levante la tapa.

2.Acomode dos bater??as alcalinas AAA de manera que coincidan los polos

positivo y negativo dentro del compartimiento de las bater??as.

3. Acomode la tapa de las bater??as en su lugar.

Ahorrador de bater??as

Su control remoto se desactiva autom??ticamente si los botones se oprimen m??s de 30 segundos continuos. Esto permite que las bater??as conserven su carga en caso de que el control remoto se atore en un lugar donde los botones se puedan oprimir solos (por ejemplo, entre los cojines del sof??).

Almac??n de c??digos

Los c??digos est??n almacenados en la memoria permanente, as?? que no se perder?? ning??n c??digo almacenado en el control remoto mientras usted cambia las bater??as.

Encendido por omisi??n

El control remoto se enciende en la modalidad de TV

Fijaci??n de c??digos

El bot??n de b??squeda de c??digos (CODE SEARCH) se utiliza para fijar el control remoto. Puede fijar el control utilizando el c??digo de su marca de aparato, de las tablas de c??digos (vea la hoja separada), o puede buscar en la biblioteca de c??digos hasta que encuentre un c??digo que funcione para su aparato. Por favor consulte la secci??n de ???Programaci??n con b??squeda de c??digos??? en la p??gina 28 para obtener m??s informaci??n sobre el uso de la funci??n de b??squeda de c??digos y aprender a hacer una b??squeda en la biblioteca de c??digos para sus productos.

NOTA: Tambi??n puede almacenar cualquier tipo de c??digo bajo cualquier modalidad (salvo TV). Es decir, puede almacenar un c??digo de videocasetera en el bot??n CBL, o un c??digo de cable en el bot??n de VCR, etc. Sin embargo, ??nicamente puede almacenar c??digos de TV en el bot??n de

TV.

27

Preparaci??n, cont.

Ingreso Directo de C??digos

1.Oprima, sin soltar, el bot??n CODE SEARCH hasta que el indicador rojo permanezca encendido. Suelte el bot??n

CODE SEARCH.

2.Oprima y suelte el bot??n de la modalidad deseada (TV, VCR, etc.). El indicador rojo parpadea y enseguida se queda encendido.

3.Ingrese el c??digo de 4 cifras de las tablas de c??digos (en la hoja separada). Nota: despu??s de ingresar un c??digo v??lido, el indicador rojo se apaga. Cuando se ingresa un c??digo inv??lido, el indicador rojo parpadea.

4.Con su aparato encendido, oprima CHANNEL UP. Si el aparato responde, ya no se requiere ninguna programaci??n

adicional. Nota: si algunos botones no hacen funcionar su equipo, trate uno de los dem??s c??digos para su marca.

Escriba aqu?? los c??digos para futura referencia.

TVTV

VCR

CBL

DVD

CD

SAT

AUX

Programac??on con B??squeda de codigos (Code Search)

Si su aparato no responde despu??s de haber intentado todos los c??digos de la marca de su aparato, o si la marca no aparece en la lista, trate de buscar su c??digo siguiendo los pasos a continuaci??n.

1.Encienda manualmente el aparato (TV, VCR, etc.) que se habr?? de controlar.

2.Oprima, sin soltar, el bot??n CODE SEARCH hasta que el indicador rojo permanezca encendido. Suelte el bot??n

CODE SEARCH.

3.Oprima y suelte el bot??n de la modalidad deseada (TV, VCR, etc.). El indicador rojo parpadea una vez.

4.Oprima el bot??n CHANNEL UP (hacia arriba) repetidamente (hasta 300 veces) hasta que el aparato que se ha de controlar cambie de canal. El indicador rojo parpadea con cada opresi??n de bot??n. Si accidentalmente se pasa del c??digo deseado, oprima el bot??n CHANNEL DOWN (hacia abajo) para retroceder hacia la biblioteca hasta que el aparato cambie de canal. Oprimir el bot??n CHANNEL UP cambia la direcci??n hacia delante nuevamente.

5.Oprima y suelte el bot??n MUTE para fijar el c??digo.

28

Preparaci??n, cont.

Programac??on con B??squeda de codigos (Code Search)

La mayor??a de los usuarios almacenan los c??digos de videocasetera en el bot??n de VCR, los c??digos del Cable en el bot??n de CABLE, etc. Por ejemplo, si desea almacenar un c??digo de videocasetera en cable, siga primero el procedimiento para la Entrada directa de c??digos (p??gina previa) y oprima CBL en el paso 2 de la Entrada directa de c??digos. A continuaci??n ingrese CUALQUIER c??digo de VCR en el paso 3 de la Entrada directa de c??digos. Luego siga los pasos anteriores para la B??squeda de c??digos (o B??squeda de c??digos por marca, vea abajo). Nota: Si el aparato no tiene un bot??n de CHANNEL UP (subir de canal), utilice PLAY (en VCR solamente) o POWER. La b??squeda de c??digos inicia a partir del n??mero de 4 cifras almacenado actualmente bajo esa modalidad.

B??squeda de C??digos por Marcas

Le permite buscar un c??digo de una marca espec??fica en la biblioteca de c??digos para un fabricante en particular.

1.Encienda el aparato (TV, VCR, etc.) que se ha de controlar.

2.Oprima sin soltar el bot??n CODE SEARCH (b??squeda de c??digos) hasta que el indicador rojo permanezca encendido, y enseguida suelte el bot??n.

3.Oprima y suelte r??pidamente el bot??n de la modalidad deseada (TV, VCR, etc.). El indicador rojo parpadea una vez.

4.Oprima y suelte el bot??n num??rico (0-9) correspondiente al Fabricante deseado (vea la tabla en la hoja de la lista de c??digos). El indicador rojo parpadea una vez y se apaga.

Observe que al oprimir el ???0??? se efect??a una b??squeda completa de la biblioteca igual al M??todo de b??squeda de c??digos de la p??gina anterior.

5.Oprima el bot??n CHANNEL UP (subir de canal) ((o POWER o PLAY (en la videocasetera solamente)) repetidamente hasta que el aparato que se ha de controlar cambie de canal. El indicador rojo parpadea con cada opresi??n de bot??n. Si accidentalmente se pasa del c??digo requerido, oprima el bot??n CHANNEL DOWN (bajar de canal) para retroceder en la biblioteca hasta que el aparato cambie de canal. Al oprimir el bot??n CHANNEL UP se cambia la direcci??n para seguir hacia adelante nuevamente.

6.Oprima y suelte MUTE para instalar el c??digo.

La entrada del M??todo de b??squeda de marca est?? completo. Nota: Cuando se han buscado todos los c??digos bajo una Marca, el indicador rojo parpadea r??pidamente durante 3 segundos.

29

Preparaci??n, cont.

Funci??n de Identificaci??n de C??digos

La funci??n de identificaci??n de c??digo permite identificar el c??digo de librer??a de 4 d??gitos almacenado en la tecla del dispositivo. Por ejemplo, si desea descubrir qu?? c??digo de 4 d??gitos est?? almacenado en su tecla de TV, siga los seis pasos siguientes:

1.Oprima, sin soltar, el bot??n CODE SEARCH hasta que el indicador rojo permanezca encendido. Suelte el bot??n

CODE SEARCH.

2.Oprima y suelte el bot??n de la modalidad deseada (TV, VCR, etc.). El indicador rojo parpadea y luego permanece encendido.

3.Oprima y suelte el bot??n CODE SEARCH. La luz indicadora parpadea y se apaga.

4.Para encontrar la primera cifra para el c??digo almacenado bajo el bot??n de modalidad oprimido en el paso 2, oprima cada bot??n num??rico del 0 al 9. Cuando la luz indicadora parpadea y se apaga, el n??mero que oprimi?? es la primera cifra para el c??digo que est?? buscando.

5.Para encontrar la segunda cifra, repita el paso 4, esta vez cuando la luz indicadora parpadee y se apague, esta es la segunda cifra.

6.Repita el paso 4 para encontrar los terceros y cuartos d??gitos.

Cronometro de apagado autom??tico

El bot??n SLEEP (apagado autom??tico) habilita la funci??n de apagado autom??tico de su dispositivo, proporcionado que su aparato tenga esta funci??n. Alternativamente, usted pude programar el control remoto para apagar su TV despu??s de un periodo de 1 a 99 minutos. Esta caracter??stica esta solamente disponible en el modo TV y el control remoto debe estar en el modo de TV para fijar el cronometro de apagado autom??tico. Esta funci??n puede ejecutarse aun si su televisor no tiene esta caracter??stica.

1.Presione y suelte la tecla de modo TV.

2.Presione y mantenga presionado el bot??n CODE SEARCH (b??squeda de c??digo) hasta que el indicador rojo permanezca encendido. Suelte el bot??n CODE SEARCH.

3.Oprima y suelte el bot??n SLEEP (observe, el apagado autom??tico previamente fijado es cancelado a este punto y el control remoto vuelve a la operaci??n normal).

4.Oprima y suelte los botones num??ricos (01-99) para seleccionar el tiempo que desee que transcurra. El indicador rojo se apagara brevemente para indicar la aceptaci??n de la presi??n del bot??n y quedara apagado despu??s de la segunda presi??n de bot??n.

5.El cronometro de apagado autom??tico del televisor quedara configurado.

6.Deje el control remoto apuntando hacia el televisor sin que haya obstrucci??n alguna entre ambos

Para cancelar le Cronometro de apagado autom??tico, oprima y suelte el bot??n POWER (encendido) en el modo TV, o repita los pasos 1, 2 y 3 mencionados arriba.

30

Preparaci??n, cont.

C??digos de programaci??n de equipos combinados

Algunos equipos combinados (combos) (por Ej. TV/VCR, TV/DVD, DVD/VCR, etc.) requerir??n que ajuste dos tipos diferentes de botones de Modo para controlar ambas partes del equipo combinado. Por ejemplo, si cuenta con un Combo TV/DVD, es posible que deba ajustar un c??digo en el bot??n TV para controlar la parte de la television y otro c??digo adicional (en cualquier otro bot??n de Modo) para controlar la parte de DVD.

Control de equipos combinados

Algunos equipos combinados (por Ej. TV/VCR, TV/DVD, DVD/VCR, etc.) tienen botones diferentes en el control remoto original para seleccionar la parte del equipo combinado a ser controlado. Por ejemplo, si su equipo combinado es un DVD/VCR entonces es posible que su control remoto original tenga botones diferentes para DVD y VCR para seleccionar la parte del combo que quiera controlar. Puede encontrar las funciones equivalents a los botones en su control remoto Philips, utilizando los botones de Modo y

CODE SEARCH del mismo.

Vea ???Programaci??n con b??squeda de c??digo??? en la P??g. 28 para ajustar un Modo de equipo (por Ej. DVD) con el c??digo correcto para su equipo combinado. Tomando como ejemplo el equipo combinado DVD/VCR y asumiendo que su c??digo est?? programado bajo el Modo DVD, presione y mantenga presionado el bot??n de Modo DVD durante m??s de un segundo para enviar el comando del bot??n DVD. Para enviar el comando del bot??n VCR, presione y suelte r??pidamente el bot??n CODE SEARCH (b??squeda de c??digo) y a continuaci??n presione y suelte el bot??n de Modo DVD. Este m??todo puede ser aplicado en forma similar para todos los equipos combinados (por Ej. TV/VCR, TV/DVD, DVD/VCR, etc.) y est?? disponible para todos los Modos. Nota: Tenga en cuenta que esta caracter??stica no acepta todos los c??digos.

Control de equipos que requieren botones de encendido y apagado diferentes

Algunos equipos (por ej. algunos televisores RCA) requieren botones diferentes para encender y para apagar el equipo. Puede encontrar las funciones equivalentes a los botones en su control remoto Philips, utilizando los botones de Modo y POWER del mismo. Vea ???Programaci??n con b??squeda de c??digo??? en la P??g. 28 para ajustar un Modo de equipo (por ej. TV) con el c??digo correcto para su equipo. Asumiendo que el televisor es el ejemplo y que el c??digo a ser programado es el Modo TV, para encender su TV presione y sostenga el bot??n de Modo TV durante m??s de un segundo para transmitir el comando del bot??n de encendido. Paga apagar el televisor, presione y suelte el bot??n POWER para transmitir el comando del bot??n de apagado.

31

Este m??todo puede ser aplicado en forma similar para cualquier equipo y est?? disponible para todos los Modos. Nota: Tenga en cuenta que esta caracter??stica no admite todos los c??digos.

Funci??n de traspaso de VCR/DVD/DVR

Este control remoto permite la traslaci??n de los 6 botones de transporte de cinta VCR (PLAY (reproducci??n), PAUSE (pausa), STOP (detener), FF (avance), REWIND (rebobinar), y REC (grabar) desde cualquier Modo programado con c??digos de TV, SAT o CABLE al ??ltimo Modo de VCR, DVD o DVR utilizado. Normalmente otros tipos de controles remotos ??nicamente permiten traspasar (desde otro Modo) los 6 botones de VCR al equipo programado en el bot??n de Modo VCR. Esto no es de mucha utilidad si est?? utilizando un DVD programado en un Modo que no sea VCR. Por ejemplo, si tiene tres equipos DVD, VCR o DVR programados en este control remoto, el ??ltimo que utiliz?? en el control remoto ser?? el que tenga el control de los 6 botones de VCR transportados mientras est?? en cualquier otro Modo. Esta prestaci??n no funcionar?? si el c??digo de TV, SAT o CABLE programado tiene su propio control de botones de transporte de VCR, como por ejemplo un TV Combo, SAT/ PVR, etc.

Control de volumen/silencio y traspaso

Este control remoto le permite seleccionar que Modo de equipo controla los botones de volumen/silencio. Inicialmente este control est?? ajustado (de f??brica) para que todos los Modos de equipos programados con c??digos ???Visual??? (por ej. TV, VCR, DVD, DVR, SAT & CABLE) y c??digos de ???Audio??? (por ej. CD & AUDIO) utilicen su propia funci??n de control de volumen/silencio cuando la tengan. Si el c??digo ???Visual??? programado no tiene operaci??n propia de volumen/silencio, entonces esos botones traspasar??n el control al equipo del Modo de TV sin necesidad de cambiar al Modo TV. Por informaci??n m??s detallada, vea ???Ajuste del control de volumen/silencio y traspaso???. Por favor refi??rase a la pagina siguiente.

Cualquier modo seleccionado para el control de volumen/silencio DEBE contar con su propia funci??n de volumen/silencio o los botones de volumen/silencio no funcionaran.

Ajuste de TODOS los controles de Volumen/ Silencio a cualquier modo.

Esta rutina puede ajustar todos los modos para priorizar a cualquier modo seleccionado para el bot??n de control de volumen/silencio sin necesidad de cambiar a ese modo.

1.Presione y mantenga presionado el bot??n CODE SEARCH hasta que el indicador rojo se encienda, luego su??ltelo.

2.Presione y mantenga presionado el bot??n MUTE hasta que el indicador rojo destelle, luego su??ltelo.

3.Presione y suelte el bot??n de modo deseado (TV, VCR, etc.) para el control de volumen/silencio, el indicador rojo destella y luego permanece encendido.

4.Presione y suelte el bot??n MUTE y el indicador rojo se apaga. El indicador rojo destellar?? r??pidamente durante tres segundos si el modo que ha seleccionado no tiene control de volumen/silencio.

5.Todos los dem??s modos priorizar??n al modo que usted ha elegido para el control de volumen/silencio.

6.Todos los modos programados ???visual??? y ???audio??? ahora fun- cionaran con los modos respectivos que usted ha elegido para el control de volumen / silencio.

Configuraci??n de Control de Volumen/ Silencio para Cualquier Modo

Esta rutina puede fijar cualquier modo para el uso solamente de su propio control de Volumen/Silencio. Nota - si su modo elegido no tiene ninguna funci??n de volumen/silencio propio entonces los botones de volumen/silencio no har??n nada.

1.Presione y mantenga presionado el bot??n CODE SEARCH hasta que el indicador rojo se encienda, luego su??ltelo.

2.Presione y mantenga presionado el bot??n MUTE hasta que el indicador rojo deje de destellar, luego su??ltelo.

3.Presione y suelte el bot??n de modo deseado (TV, VCR, etc.), el indicador rojo destella y luego queda encendido.

4.Presione y suelte el bot??n de VOLUMEN- (abajo), el indicador rojo destella y luego queda encendido.

5.Presione y suelte el bot??n MUTE y el indicador rojo se

apaga.

5.Todos los modos programados ???visual??? y ???audio??? ahora funcionaran con los modos respectivos que usted ha elegido para el control de volumen/silencio.

Transferencia de c??digos

La funci??n de aprendizaje (transferencia) le permite a este control remoto ???aprender??? funciones de su control remoto original. Por ejemplo, es posible que usted desee usar su control remoto la funci??n RANDOM PLAY (reproducci??n al azar) del control remoto original de su reproductor de discos compactos. Este control remoto esta equipado con una funci??n de ???aprendizaje f??cil??? que le permite aprender funciones (tales como RAN- DOM PLAY del control remoto original de su reproductor de discos compactos).

Consejos Para elAprendizaje

Solamente puede aprender un tipo de equipo bajo un bot??n de modo, o sea, s??lo puede aprender c??digos de TV en el modo TV, c??digos de VCR en el modo VCR, etc. Si usted est?? intentando aprender las funciones de un control remoto ???universal???, podr??a tener m??s de un tipo de c??digo guardado bajo un modo determinado. Intente aprender funciones de otro control remoto para verificar si existe un problema con el tipo o marca del control remoto del cual est?? intentando adquirirlas.

a.Algunas funciones de algunos tipos de controles remotos no pueden ser aprendidas.

b.No podr??n almacenar funciones bajo los botones LEARN(aprender)oCODESEARCH(b??squedade c??digo).

c.??nicamente puede transferir las funciones de un tipo de equipo original por modo individual.

d.Utilice bater??as nuevas tanto en el control remoto de aprendizaje como en el original.

e.Durante el proceso de aprendizaje, mantenga una distancia m??nima de tres pies de luces incandescentes o de baja energ??a.

f.Antes del aprendizaje ejecute un Despejado Maestro (ver P??g. 38) e intente adquirir inicialmente 2 o 3 comandos. Luego realice una Despejado maestro antes de realizar el aprendizaje completo de los comandos de su control remoto original.

g.Coloque el control original extremo con extremo con el control de aprendizaje, de modo que los transmisores infrarrojos de ambos est??n directamente alineados entre s??. Es posible que tenga que ajustar la altura de alguno de los controles para lograr esto. Utilice la funci??n de b??squeda de transmisor IR como ayuda.

34

Tips On Learning, cont.

h.Mantenga una distancia de aproximadamente una pulgada entre los dos remotos y no los mueva ni cambie la distancia entre ellos, hasta que haya adquirido todas las funciones de botones para ese modo.

i.Durante el proceso de aprendizaje, mantenga presiona do el bot??n que est?? siendo adquirido hasta que el indicador rojo haya destellado durante medio segundo.

j.Evite transferir las funciones del bot??n Volume/Mute de su control remoto original salvo que est?? seguro de que opera el mismo equipo. Tenga en cuenta que algunos controles remoto de DVD originales incluyen un bot??n de control volumen/silencio para TV y pueden tener dos tipos distintos de c??digo.

k.Evite transferir las funciones de los botones de transporte de VCR de su control remoto original salvo que est?? seguro de que operan el mismo equipo. Tenga en cuenta que algunos controles remotos de TV originales incluyen botones de control de VCR y pueden tener dos tipos distintos de c??digo.

l.Si el aprendizaje del primer o segundo bot??n para un modo causa sucesivos errores, entonces intente lo siguiente:

i.Finalice la sesi??n de aprendizaje presionando la tecla

CODESEARCH.

ii.Elimine los comandos adquiridos para ese modo.

iii.Verifique que los transmisores IR est??n correctamente alineados entre los dos controles remoto (utilice la funci??n de b??squeda de transmisor IR).

iv.Disminuya (media pulgada) o aumente (2 pulgadas) la distancia entre los dos controles.

v.Intente transferir nuevamente las funciones del control remoto original para ese modo.

Si surgen problemas nuevamente con el mismo bot??n, revise el bot??n del control remoto original a ser transferido. ??Transmite? ??Opera el equipo destinatario? Intente adquirir las funciones de ese bot??n bajo un modo diferente. Si lo adquiere correctamente probablemente se trate de un c??digo de tipo diferente a los otros y no puede ser adquirido bajo el mismo modo.

35

B??squeda de transmisor IR (infrarrojo)

Esta funci??n le ayuda a identificar donde est?? ubicado el transmisor IR de su control remoto original y es especialmente ??til si el mismo est?? escondido detr??s de un lente.

1.Enfrente ambos controles remotos a una distancia de aproximadamente 1 pulgada entre ellos (vea ???Consejos para el aprendizaje de c??digos??? en las p??ginas anteriores.)

2.Presione y mantenga presionado el bot??n de CODE SEARCH hasta que el indicador rojo se encienda, luego su??ltelo.

3.Presione y suelte el bot??n del modo deseado (TV, VCR, etc.), el indicador rojo parpadea y luego permanece encendido.

4.Presione y suelte el bot??n LEARN (aprender), el indicador rojo parpadea y luego permanece encendido.

5.Presione y mantenga cualquier bot??n del control remoto original y mueva el control remoto original a la izquierda y a la derecha, y/o arriba y abajo frente al transmisor infrarrojo del control de adquisici??n. El indicador rojo permanecer?? encendido si no encuentra la se??al infrarroja del remoto original y destellar?? m??s r??pido cuando los transmisores infrarrojos est??n alineados. El punto en el cual el indicador rojo destella con mayor rapidez es donde los dos transmisores infrarrojos est??n alineados. Nota: Algunos controles remotos originales ??nicamente transmitir??n IR la primera vez que oprima el bot??n y luego se detendr??n. En estos casos, r??pidamente presione y libere el bot??n del control remoto original repetidamente durante este procedimiento.

6.Ahora podr?? aprender las funciones de un bot??n de su control remoto original, continuando a partir del ???paso 4??? de la secci??n ???Aprendizaje de comandos??? de la p??gina siguiente, o, para salir a esta altura, presione y libere el bot??n CODE SEARCH.

Aprendizaje de Comandos

La funci??n de aprendizaje le permite a este control remoto ???aprender??? funciones de su control remoto original. Por ejemplo, es posible que usted desee usar su control remoto para ejecutar la funci??n RANDOM PLAY (reproducci??n al azar) del control remoto original de su reproductor de discos compactos. Este control remoto est?? equipado con una funci??n de ???aprendizaje f??cil??? que le permite aprender funciones (tales como RANDOM PLAY del control remoto original de su reproductor de discos compactos) siguiendo los pasos que se indican a continuaci??n:

1.Presione y mantenga presionado el bot??n CODE SEARCH (b??squeda de c??digo) hasta que el indicador rojo se encienda; luego, suelte el bot??n.

2.Presione y suelte el bot??n del modo deseado (TV, VCR, etc.); el indicador rojo parpadear?? y luego quedar?? encendido.

3.Presione y suelte el bot??n LEARN (aprender); el indicador rojo parpadear?? y luego quedar?? encendido.

4.Presione y suelte el bot??n del control remoto donde quiera que quede memorizada la funci??n a aprender [por ejemplo POWER (encendido)].

5.Apunte ambos controles remotos uno frente al otro, a una distancia de alrededor de una pulgada (aprox. 2,5 cm) uno del otro (ver Consejos en la p??gina 34).

6.Presione y mantenga presionado el bot??n del control remoto original [por ejemplo PLAY (reproducci??n)] hasta que el indicador rojo parpadee una vez y quede encendido. Si hay alg??n problema de aprendizaje, el indicador parpadear?? durante tres segundos y quedar?? encendido. Si esto ocurre, repita los pasos 4 a 6.

7.Repita los pasos 4 a 6 para los otros botones que quiera aprender.

8.Presione y suelte el bot??n CODE SEARCH cuando se haya concluido el aprendizaje de todos los comandos deseados del control remoto. El aprendizaje de c??digos est?? ahora completo.

6.

Alinee el control remoto (del cual est?? aprendiendo) frente a frente con el control remoto que realiza el aprendizaje, sobre una superficie firme, alejados aproximadamente una pulgada (2,5 cm).

1. 3.

Despejando Comandos

Para Despejar Todos los Comandos Transferidos bajo una modalidad

Borrar los comandos que se han aprendido puede serle ??til si, por ejemplo, reemplaza su reproductor de discos compactos por uno de otra marca o modelo. Si este control remoto ha aprendido, por ejemplo, la funci??n RANDOM PLAY (reproducci??n al azar) del control remoto original de su viejo reproductor de discos compactos, esa funci??n podr??a no poder ejecutarse en un reproductor nuevo. En caso de que quiera quitar o borrar uno o m??s comandos ???aprendidos???, siga los pasos siguientes:

1.Oprima, sin soltar, el bot??n CODE SEARCH hasta que se encienda la luz indicadora. Suelte el bot??n

CODESEARCH.

2.Oprima y suelte el bot??n de la modalidad que desee despejar (TV, VCR, etc.). El indicador parpadea y se apaga.

3.Oprima y suelte el bot??n LEARN DOS VECES. El indicador parpadea y se apaga.

4.Oprima y suelte el CODE SEARCH. El indicador parpadea y se apaga. Todos los comandos transferidos bajo esa modalidad se han despejado.

Despejado Maestro: Para Despejar Todos los Comandos Transferidos, es Decir, Regresar a las Funciones por Omisi??n de Fabrica

1.Oprima, sin soltar, el bot??n CODE SEARCH hasta que la luz indicadora se encienda. Suelte el bot??n

CODESEARCH.

2.Oprima y suelte el bot??n LEARN DOS VECES. El indicador parpadea y se apaga.

3.Oprima y suelte el CODE SEARCH. El indicador parpadea y se apaga. Todos los comandos transferidos en el control remoto se han despejado.

38

Extendedor IR

El extendedor IR le permite utilizar su control remoto PH750 para controlar el producto A/V al cual est?? conectado el emisor de audio/video. Por ejemplo, si el emisor de audio/video est?? conectado a un reproductor de DVD o VCR en su sala, y el receptor de audio/video est?? conectado a un televisor en su dormitorio, puede controlar el reproductor de DVD o VCR mientras ve la imagen en el televisor de su dormitorio. El control remoto env??a comandos de radiofrecuencia (RF) al emisor de audio/video (la unidad que tiene la antena delgada). Este recibe los comandos de RF desde el control remoto y los convierte en comandos infrarrojos (IR). Debe conectar el cable extensor IR en el conector de la parte trasera del emisor de audio/video y los emisores IR en la parte frontal del reproductor de DVD o VCR, etc., que desea controlar.

1.Conecte el conector del extensor IR en el cable emisor IR en el enchufe IR EXT ubicado en la parte trasera del emisor de audio/video.

2.Coloque el cable emisor en la parte frontal de los dos dispositivos que desea controlar (por ejemplo, DVD y VCR).

3.Aseg??rese de que los dos emisores IR est??n conectados cerca de los sensores IR en los dispositivos que desea controlar.

El cable del emisor IR le permite controlar hasta dos dispositivos IR.

39

Localizaci??n y reparaci??n de aver??as

El Control Remoto no Opera su Producto

???Oprima el bot??n de modalidad del aparato que desea controlar.

???Programe el control remoto con un nuevo c??digo.

???Instale bater??as nuevas (quiz?? tenga que reprogramar su control remoto despu??s de instalar bater??as nuevas).

???Puede ser que el control remoto no sea compatible con su aparato.

El Control Remoto no Opera Algunas Funciones de su Aparato

???Programe el control remoto con un c??digo nuevo.

???Puede ser que el control remoto no sea capaz de operar todas las funciones de su aparato o los nombres de los botones pueden ser diferentes a los de su aparato.

La Luz Indicadora Parpadea Despu??s de que Programa un C??digo de Producto

???El control remoto no acept?? el c??digo.

???Intente programar el c??digo otra vez o trate un c??digo diferente.

Para solicitar ayuda con la configuraci??n, por favor llame al tel??fono (919) 573-7854.

Garant??a limitada de por vida

El fabricante garantiza que este producto carece de defectos de material, manufactura o armado, bajo uso normal y de acuerdo con las especificaciones y advertencias, durante el tiempo que ??ste sea de su propiedad. Esta garant??a cubre ??nicamente al comprador original del producto y no es transferible.

Los productos defectuosos deben ser devueltos al comercio vendedor, junto con la prueba de compra que

indique la fecha, para su reparaci??n o reposici??n. NO EXISTEN OTRAS GARANT??AS EXPL??CITAS. No se aceptan reclamos por da??os incidentales e indirectos, de acuerdo a lo permitido por la ley. Esta garant??a le otorga derechos legales espec??ficos, y usted puede tener otros derechos que pueden variar de estado a estado.

Hecho en China-TC,

Aseguraci??n de calidad en Estados Unidos

Ledgewood, New Jersey 07852

Advertencia de la FCC

ESTE DISPOSITIVO CUMPLE CON LA

PARTE 15 DE LAS NORMAS DE LA FCC. SU

OPERACI??N EST?? SUJETA A LAS

SIGUIENTES DOS CONDICIONES: (1) ESTE

DISPOSITIVO PUEDE NO PROVOCAR

INTERFERENCIA NOCIVA, Y (2) ESTE

DISPOSITIVO DEBE ACEPTAR CUALQUIER

INTERFERENCIA RECIBIDA, INCLUYENDO

CUALQUIER INTERFERENCIA QUE PUEDA

PROVOCAR UNA OPERACI??N NO

DESEADA.

Eradiofrecuencia, y si no se instala y utiliza correctamente, es decir, estrictamente de acuerdo con las instrucciones del fabricante, puede provocar interferencia con la recepci??n de radio y televisi??n. Ha sido probado y se ha determinado que cumple con los l??mites para dispositivos de control remoto de acuerdo con las especificaciones contenidas en las Sub-Partes B y C de la Parte 15 de las Normas de la FCC, que est??n dise??adas para ofrecer una protecci??n razonable contra dicha interferencia en una instalaci??n residencial. Sin embargo, no se puede garantizar que no ocurra interferencia en alguna instalaci??n en particular. Si el equipo ocasiona interferencia en la recepci??n de radio o televisi??n, lo cual puede ser determinado desenchufando el equipo, intente corregir la interferencia mediante una o m??s de las siguientes medidas:

???Reoriente la antena de la radio/TV que experimenta la interferencia.

???Ubique el receptor en otro lugar con respecto a la radio/TV.

???Mueva el receptor m??s lejos de la radio/TV.

???Conecte el receptor en una toma de un circuito el??ctrico diferente al de la radio/TV que est?? experimentando la interferencia.

???De ser necesario, consulte a su proveedor local por m??s sugerencias.

NOTA: Toda modificaci??n a cualquiera de los componentes de este equipo anular?? la autoridad del usuario para operarlo.

Made in China. Quality Assured in USA.

Ledgewood, NJ 07852

PH750T-BL-12/06