PLAYING A CD

This CD player can play all kinds of Audio Discs such as

CD-Recordables and CD-Rewritables. Do not try to play a

CD-ROM, CDi, VCD, DVD or computer CD.

1 Push OPEN 2 to open the CD compartment lid.

2 Insert an audio CD, printed side up, by pressing the CD center onto the hub.

3 Close the player by pressing the lid down.

MODE

4 Press 2; to switch the player on and start CD playback.

yThe current track number and the elapsed playing time are displayed.

???You can pause playback by pressing 2;.

yThe time where playback was paused will ???ash.

???You can continue playback by pressing 2; again.

5Press 9 to stop playback.

yThe total number of tracks and the total playing time of the CD are displayed.

6 Press 9 again to switch off the player.

???To remove the CD, hold it by its edge and press the hub gently while lifting the CD.

Note: If there is no activity, the unit will automatically switch off after a while to save energy.

PLAYBACK INFORMATION

???If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed. In that case, use FINALIZE on your CD- recorder to complete the recording.

???If you want to play a CD-Rewritable (CD-RW), it takes 3???15 seconds for sound reproduction to start once you have pressed 2;.

???Playback will stop if you open the CD lid.

???While the CD is being read, 1 -:- ???ashes in the display.

VOLUME AND BASS

Volume adjustment

Adjust the volume by using VOL E.

This product complies with the radio interference requirements of the European Union.

Both the model number and production number are located on the bottom of the set.

SELECTING A TRACK AND SEARCHING

Selecting a track during playback

???Brie???y press ??? or ?? once or several times to skip

to the beginning of the current, previous or next track.MODE

Selecting a track when playback is stopped

1Brie???y press ??? or ?? once or several times. yThe selected track number is displayed.

2Press 2; to start CD play.

yPlayback starts with the selected track.

Searching for a passage during playback

1Keep ??? or ?? pressed to ???nd a particular passage in a backward or forward direction.

ySearching is started and playback continues at

low volume. After 2 seconds the search speed increases.

2Release the button when you reach the desired passage. yNormal playback continues from this position.

Notes: ??? During SHUFFLE, SHUFFLE REPEAT ALL, REPEAT or while playing a program, searching is only possible within the particular track.

PROGRAMMING TRACK NUMBERS

2Press PROGRAM to store the track. yPROGRAM lights; the track number

programmed and P, with the total number of stored tracks, are displayed.

3 Select and store all desired tracks in this way.

4Press 2; to start playback of your selected tracks. yPROGRAM is shown and playback starts.

???You can review the program by pressing PROGRAM for more than 2 seconds.

yThe display shows all stored tracks in sequence.

Notes: ??? If you press PROGRAM and no track is selected, SELECt is displayed.

??? If you try to store more than 15 tracks, FULL is displayed.

Clearing the program

???While playback is stopped, press 9 to clear program. yCLEAr is displayed once, PROGRAM

disappears, and the program is cleared.

Notes: ??? The program also will be cleared if you

???interrupt the power supply, or

???open the CD compartment lid, or

???if the unit switches off automatically.

MODE

It is possible to play tracks in random order, to repeat a single track or the entire CD.

1Press MODE during playback as often as required in order to activate one of the following ???modes???. The

active mode is shown in the display.

ySHUFFLE: All tracks of the CD are played in random order until all of them have been played once.

ySHUFFLE REPEAT ALL: All tracks of the CD are played repeatedly in random order.

yREPEAT: The current track is played repeatedly.

yREPEAT ALL: The entire CD is played repeatedly.

2 Playback starts in the chosen mode after 2 seconds.

???To return to normal playback, press MODE repeatedly until the display shows no active modes.

MODE PROGRAM

TROUBLESHOOTING

If a fault occurs, ???rst check the points listed below before taking the set for repair.

If you are unable to remedy a problem by following these hints, consult your dealer or service centre.

WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. Do not open the set as there is a risk of electric shock!

No power, playback does not start

Batteries

???Batteries inserted incorrectly

??? Insert the batteries correctly

???Batteries are empty

???Change the batteries

??? Contact pins are dirty

???Clean them with a cloth

Mains adapter

??? Loose connection

??? Connect the adapter securely

no diSC indication

???The CD is badly scratched or dirty

??? Replace or clean the CD

???CD is not or incorrectly inserted

??? Insert a CD, label upwards

???The laser lens is steamed up

??? Wait until the lens has cleared

RESUME

nF diSC indication

You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use

the RESUME???HOLD???OFF slider for these functions. 1 Switch the slider to RESUME during playback to

activate RESUME. yRESUME is shown.

p/LINEOUT

O

RE

F

S

U

M

E

H

O

L

D

??? CD-RW (CD-R) is not recorded

??? Use FINALIZE on the properly. CD recorder to complete the recording

HoLd indication and/or no reaction to controls

???HOLD is activated

??? Deactivate HOLD

???Electrostatic discharge

??? Disconnect the set from power supply or take out the batteries for a few seconds

The CD skips tracks

2 Press 9 whenever you want to stop playback.

3Press 2; whenever you want to resume playback. yRESUME is shown and playback continues from

where you have stopped last.

???To deactivate RESUME, switch the slider to OFF. yRESUME goes off.

???The CD is damaged or dirty

??? Replace or clean the CD

???RESUME, SHUFFLE or PROGRAM is active

??? Switch RESUME, SHUFFLE or PROGRAM off

No sound or bad sound quality

HOLD

You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions.

1Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when

you press any button. If the set is switched off, HoLd will be shown only when 2; is pressed.

2 To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function.

/LINEOUT p

O

R

F

E

S

U

M

E

H

O

L

D

???PAUSE is activated

??? Press 2;

???Loose, wrong or dirty connections

??? Check and clean connections

???Volume is not adjusted

??? Adjust the volume

???Malfunctions due to nearness of active mobile phones

??? Keep the player away from active mobile phones

???Strong magnetic ???elds near the player

??? Change the player???s position or connections