Assembly Instructions

TY-S42PX20U

Placement

STEP 1 Plasma TV installation and fastening method

???Install the plasma TV by referring to the following illustration.

???Do not hold the plasma TV at the bottom of the front panel.

1.Align the support pole insertion holes of the plasma TV with the support poles (1 each), and lower the plasma TV until the poles stop. Slightly lift the left and right sides of the plasma TV and remove the corner protection pads attached to the bottom.

2.Fasten the plasma TV and support poles using assembly screws (black screws) (??? 4)

TY-S50PX20U

Display stand

The tools required:

Plus (Phillips) (+) screwdriver

IMPORTANT

A study of the assembly instructions will not only save you time, but may prevent possible damage to your new stand.

Assistance may be required for some assembly procedures.

??? Position by placing your hands at the points indicated in the illustration.

Support pole insertion hole

CAUTION : THIS STAND IS DESIGNED ONLY FOR USE WITH A PANASONIC PLASMA TV.

APPLIED MODEL : TH-42PX20, TH-50PX20

Use with other appliances may result in instability causing possible injury.

Your hardware pack contains / Replacement parts

To maintain appearance we recommend the following:

Painted Surfaces:Use a damp cloth for cleaning. Do not use any abrasive or chemically treated cleaners. NOTE: As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures or moisture, as this can result in serious irreparable damage.

For improvement purposes, design and specifications are subject to change without notice.

STEP 2 To use with equipment such as a video deck

??? Wire over the minimum distance

???To thread wiring, remove the terminal cover and pass wires along the grooves in the rear cord cover, along the groves in the left and right

REPLACEMENT PARTS LIST

When making a part (s) inquiry or for out of warranty purchases please quote part no. & description.

PANASONIC SERVICES COMPANY

2003 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3Tel. : (905) 624-8447

2003 Matsushita Electric Industeial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

Assembly & Placement

Manual

TY-S42PX20U

Model No. TY-S50PX20U

Assembly

STEP 1 Attaching of bottom panel, side panels and casters

STEP 3 Attaching of glass shelf and cord holder

1.Securely insert the casters (??? 4) into the bottom panel.

2.Align the dowels of the side panels (left and right) with the dowel holes in the bottom panel and insert.

STEP 2 Attaching of top crosspiece and rear cord cover

1.Align the dowels in the glass shelf supports (left) (??? 2) with the dowel holes in the side panel (left) and insert.

Securely fasten with the glass shelf support fastening screws (black screws) (??? 1).

2.Attach the glass shelf supports (right) in the same manner.

3.Insert a cord holder in parallel with the glass shelf supports (left and right), and align the dowels of the cord holder with the dowel holes in the glass shelf supports. Attach the other cord holder to the other glass shelf supports in the same manner.

4.Attach the caution label to one

Glass shelf supports (Left)

Glass shelf support fastening screws (Black screws)

Glass shelf supports (left and right)

1.Align the support pole (right) with the notch on the right side of the top crosspiece, and

securely fasten with the support pole fastening screws (??? 2) using a Phillips head (+) screwdriver. Fasten the support pole (left) to the left side in the same manner.

Support pole fastening screws

Support pole (Right)

Top crosspiece

Cord holder

Notches

Rear cord cover

Glass shelf Caution label

Notches

Rear cord cover fastening screws (Black screws)

Glass shelf fastening screws

The tools required:

Plus (Phillips) (+) screwdriver

??? Do not use electric powered screwdrivers.

???Position the glass shelf such that the caution label is on the top surface, on the near side.

???Do not load either glass shelf with equipment weighing over 12 kg (26 Ib.). Do not load the bottom storage area with equipment weighing over 20 kg (44 Ib.).