Owner???s Manual
Model No.
The illustration shows the image of the unit
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read the instructions completely.
Please keep this manual for future reference.
If you have any questions contact
U.S.A. and Puerto Rico :
Canada :
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
???Reorient or relocate the receiving antenna.
???Increase the separation between the equipment and receiver.
???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
???Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.:
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This device complies with Part 15 of FCC Rules and
(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Contains FCC ID: RYYWYPAEBUX4 Contains
This transmitter must not be
This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and
[BTT770]
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
???Reorient or relocate the receiving antenna.
???Increase the separation between the equipment and receiver.
???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
???Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded interface cables must be used with this equipment. Operation with
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.:
WARNING:
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be
[BTT770]
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian
[BTT770] [BTT370]
THE FOLLOWING APPLIES ONLY IN CANADA. For main unit
Product Identification Marking is located on the bottom of the unit.
[BTT770]
For wireless system
Product Identification Marking is located on the bottom of wireless system.
VQT3D27
2
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference.
1Read these instructions.
2Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5Do not use this apparatus near water.
6Clean only with dry cloth.
7Do not block any ventilation openings. Install in accordance with the manufacturer???s instructions.
8Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9Do not defeat the safety purpose of the polarized or
A
10Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11Only use attachments/accessories specified by the manufacturer.
12Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
WARNING
Unit
To reduce the risk of fire, electric shock or product damage,
???Do not expose this unit to rain, moisture, dripping or splashing.
???Do not place objects filled with liquids, such as vases, on this unit.
???Use only the recommended accessories.
???Do not remove covers.
???Do not repair this unit by yourself. Refer servicing to qualified service personnel.
CAUTION
Unit
???This unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
???Do not place sources of naked flames, such as lighted candles, on this unit.
Placement
To reduce the risk of fire, electric shock or product damage,
???Do not install or place this unit in a bookcase,
???Do not obstruct this unit???s ventilation openings with newspapers, tablecloths, curtains, and similar items.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ???dangerous voltage??? within the product???s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
(Inside of product)
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
VQT3D27
3
Getting started
Radio
VQT3D27
4
???This Owner???s Manual is applicable to models
???Operations in this Owner???s Manual are described mainly with the remote control, but you can perform the operations on the main unit if the controls are the same.
Indicates features applicable to:
[BTT770]:
[BTT370]:
[BTT270]:
[BTT273]:
Getting started
???Some accessories and external devices mentioned in this Owner???s Manual that are not included with this product may not be on sale in certain regions.
???Please note that the actual controls and components, menu items, etc. of your
Accessory
Check the supplied accessories before using this unit.
For accessories of speakers, refer to page 10.
[For_Canada]
Playback
Radio
TV
Optional speaker settings Advanced operations Other devices
Reference
VQT3D27
5
Control reference guide
13
Remote control
1Turn the unit on and off
2Select title numbers, etc./Enter numbers or characters ( 34)
[CANCEL]: Cancel
10These buttons are used when;
??? Operating a
1 Press and hold
2While ???SLEEP ??????? is displayed, press
???Timer selection is up to 120 minutes.
???Select ???OFF??? when canceling the setting.
???To confirm the remaining time Press and hold the button again.
13TV operation buttons
[??]: Turn the television on and off
[AV, INPUT]: Switch the input select
[i j VOL]: Adjust the volume
14Adjust the volume of the main unit
15Mute the sound
??????MUTE??? flashes on the unit???s display, while the function is on.
???To cancel, press the button again or adjust the volume.
???Muting is canceled if the unit is turned off.
16Show NETFLIX screen
VQT3D27
6
Main unit (Front)
Getting started
1Standby/on switch (POWER ??/I) (> 19)
Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.
2Open or close the disc tray (> 22)
3Adjust the volume of the main unit
4Disc tray
5Stop (> 25)
6Start play (> 25)
7SD card slot (> 22)
8Remote control signal sensor Distance: Within approx. 7 m (23 ft.)
Angle: Approx. 20o up and down, 30o left and right
9Display
10Connect iPod/iPhone (> 32)
The main unit is designed to conserve its power consumption and save energy.
[BTT770] [BTT370] Wireless system
Main unit (Rear)
1AC IN terminal (> 18)
2Speaker terminals (> 13)
3Cooling fan
4[BTT770] [BTT370] USB port for the Communication Camera
5LAN port (> 17)
6HDMI AV OUT (ARC) terminal (> 15)
7[BTT770] [BTT370] HDMI 1 IN (CABLE/SAT) terminal (> 16)
8[BTT770] [BTT370] HDMI 2 IN terminal (> 16)
9FM radio antenna terminal (> 16)
10DIGITAL AUDIO IN terminal (> 14 , 15)
11AUX terminal (> 14)
12VIDEO OUT terminal (> 14)
13[BTT770] Digital transmitter dock for supplied wireless system (> 17)
[BTT370] Digital transmitter dock for optional wireless system (> 12)
VQT3D27
7
Playable discs/Cards
??? Discs that cannot be played in this unit
Any other disc that is not specifically supported or previously described.
???
???Super Audio CD
???Photo CD
???
???Video CD and Super Video CD
???WMA discs
???DivX discs
???PAL discs
???HD DVD
???
??? Region management information
This unit plays
Example:
This unit plays
Example:
1 ALL 124
VQT3D27
8
??? Finalize
???
This unit supports high bit rate audio (Dolby Digital Plus, Dolby TrueHD,
??? Music CD
???Operation and sound quality of CDs that do not conform to
???The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio
??? 3D
???3D videos and 3D still pictures can be played back when this unit is connected to a 3D compatible TV using a High Speed
HDMI Cable.
??? 2D video can be enjoyed as 3D virtually. ( 27)
??? SD card
??? miniSD Cards, microSD Cards, microSDHC Cards and microSDXC Cards can be used, but must be used with an adaptor card. These are usually supplied with such cards, or otherwise customer provided.
???Keep the Memory Card out of reach of children to prevent swallowing.
???To protect the card???s contents, move the record prevention tab (on the SD card) to ???LOCK???.
???This unit is compatible with SD Memory Cards that meet SD Card Specifications FAT12 and FAT16 formats, as well as SDHC Memory Cards in FAT32 format (Does not support long file name.) and SDXC Memory Cards in exFAT.
???If the SD card is used with incompatible computers or devices, recorded contents may be erased due to the card being formatted etc.
???Useable memory may be slightly less than the card capacity.
???It may not be possible to play the above media in some cases due to the
type of media, the condition of the recording, the recording method and how the files were created.
???The producers of the disc can control how discs are played. So you may not always be able to control play as described in this Owner???s Manual. Read the disc???s instructions carefully.
Getting started
Unit and media care
??? Clean this unit with a soft, dry cloth
???Never use alcohol, paint thinner or benzine to clean this unit.
???Before using chemically treated cloth, carefully read the instructions that came with the cloth.
??? Clean the lens
??? Use the lens cleaner (not supplied) to clean the unit???s lens.
??? Clean discs
Wipe with a damp cloth and then wipe dry.
??? Disc and card handling precautions
???Handle discs by the edges to avoid inadvertent scratches or fingerprints on the disc.
???Do not attach labels or stickers to discs.
???Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other solvent.
???Clean any dust, water, or foreign matter from the terminals on the rear side of the card.
???Do not use the following discs:
jDiscs with exposed adhesive from removed stickers or labels (rented discs etc).
jDiscs that are badly warped or cracked. jIrregularly shaped discs, such as heart shapes.
??? To dispose or transfer this unit
The unit may keep the user settings information in the unit. If you discard this unit either by disposal or transfer, then follow the procedure to return all the settings to the factory presets to delete the user settings. ( 43, ???To return all settings to the factory preset???)
???The operation history may be recorded in the memory of this unit.
Using the remote control
Insert so the poles (+ and
???
???
R6/LR6, AA
(Alkaline or manganese batteries)
Point it at the remote control signal sensor on this unit. ( 7)
Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire.
???Do not mix old and new batteries or different types at the same time.
???Do not heat or expose to flame.
???Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed.
???Do not take apart or short circuit.
???Do not attempt to recharge alkaline or manganese batteries.
???Do not use batteries if the covering has been peeled off.
Remove batteries if the remote control is not going to be used for a long period of time. Store in a cool, dark place.
CAUTION
???Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer.
???When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal.
VQT3D27
9
STEP 1 : Preparing the speakers
Assembling the speakers
Caution
???Do not stand on the base. Be cautious when children are near.
???When carrying speakers, hold the stand and base parts.
Preparation
???To prevent damage or scratches, lay down a soft cloth and perform assembly on it.
???For wall mount, refer to page 42.
???Keep the screws out of reach of children to prevent swallowing.
Press into the groove.
Screw B
2
1
Leave about 80 mm (3 5/32q)
Tighten securely.
VQT3D27
10
[BTT370] [BTT273]
Thread the speaker cable through the base.
???Use cables with a white connector and red connector.
Leave about 110 mm (4 11/32q)
Insert the wire fully. r: White
s: Blue line
Push!
Press into the groove.
Back of the base
Getting started
Preparing cables and making connection
1 Use of the speaker cable stickers is convenient when making cable connections.
e.g. Front speaker (L)
FRONT
Lch
???
??????
A Speaker cable sticker (supplied)
B Connector
2 Connecting the speaker cables. Insert the wire fully, taking care not to insert beyond the wire insulation.
???[BTT770] Be sure to use the speaker cables that have a large connector and short cable when you use the wireless system.
e.g. Surround speaker
r: White
s: Blue line
Push!
Be sure to match the number on each sticker with the connector color.
???Be careful not to cross
???Don???t use a front speaker as a surround speaker or vice versa. Verify the type of speaker with the label on the rear of the speaker before connecting the appropriate cable.
???To avoid injury by falling or dropping the speaker, place the speaker cables with care not to stumble or hook.
???Do not hold the speaker in one hand to avoid injury by dropping the speaker when carrying.
[BTT770] [BTT370] [BTT273]
??? Preventing the speakers from falling
???Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper attachment may result in damage to the wall or speakers.
???Use a string of less than ??? 2.0 mm (3/32q), which is capable of supporting over 10 kg (22 lbs).
e.g., [BTT770]
VQT3D27
11
STEP 2 : Positioning
Caution
???The main unit and supplied speakers are to be used only as indicated in this setup. Failure to do so may lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance.
???Do not attempt to attach these speakers to walls using methods other than those described in this manual.
???Do not touch the front netted area of the speakers. Hold by the sides.
How you set up your speakers can affect the bass and the sound field.
Setup example
Place the front, center and surround speakers at approximately the same distance from the seating position. The angles in the diagram are approximate.
???Keep your speakers at least 10 mm (13/32z) away from the system for proper ventilation.
???
???
???
60??
???
120??
???
???
???
ACenter speaker
???Put on a rack or shelf not to interfere with the TV's various sensors (ambient light, etc.). Vibration caused by the speaker
can disrupt the picture if it is placed directly on the TV. B Front speakers
C Subwoofer
DSurround speakers
???Place the speakers at the same height or higher than ear level. E [BTT770] Wireless System
???Place the wireless system within approximately 10 m (33 ft.) from the main unit, and in a horizontal position with the top panel faced upward.
???To allow for proper ventilation and to maintain good airflow around the wireless system, position it with at least 5 cm (2z) of space on all sides.
???Do not use the wireless system or the digital transmitter in a metal cabinet or bookshelf.
accessory
For more details, refer to the operating instructions for the optional wireless system. ??? When using the
TTL power output is changed. ( 48)
???Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be negatively affected.
???You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods.
???Positioning speakers in front
It is possible to locate all the speakers in front of the listening position. However, the optimal surround sound effect may not be obtainable.
???Place speakers on flat secure bases.
???Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with thick curtains.
VQT3D27 ??? For optional wall mount, refer to page 42.
??? If irregular coloring occurs on your TV, turn the TV off for about 30 minutes.
If it persists, move the speakers further away from the TV.
[BTT770]
??? Wireless system
To avoid interference, maintain the following distances between the wireless system and other electronic devices that use the same radio frequency (2.4 GHz band).
Cordless phone and other electronic devices: approx. 2 m (61/2 ft.)
The wireless system will automatically seek a clear channel if any of these other devices interfere with its communication. When this happens, there is a brief interruption in audio coming from the surround speakers.
This is the normal operation of the product working to assure the best possible performance of your home theater system.
If the interference persists, try moving the other devices to another location outside the range of the wireless system or move the wireless system nearer to the main unit.
[BTT770] [BTT370]
??? Upgrade your system to
The main unit is designed to enjoy the 7.1ch surround sound. By connecting 2 units of the Panasonic wireless system
Necessary equipment:
[BTT770]
???1 optional wireless system
???2 additional speakers
[Impedance: 3 ??? to 6 ???, Speaker input power: 100 W (Min)]
[BTT370]
???2 optional wireless systems
???2 additional speakers
[Impedance: 3 ??? to 6 ???, Speaker input power: 100 W (Min)]
For more details, refer to the operating instructions for the optional wireless system.
12
STEP 3: Connections
Turn off all equipment before connection and read the appropriate owner???s manual.
Do not connect the AC power supply cord until all other connections are complete.
Speaker cable connection
Connect to the terminals of the same color.
[BTT770]
Connection with the wireless system
Getting started
??? ??? ??? ???
Main unit
SUBWOOFER CENTER FRONT SURROUND
Do not connect the surround speaker cables to the main unit when using the wireless system.
??????
Wireless System
SPEAKERS
ENCEINTES
LS / RB LB / RS
must be set in the center position.
Connection with the main unit
13
Connection to a TV
???The basic connection is shown in the included Easy Setting Guide, however, there are more connection examples to optimize your system setting.
???Do not make the video connections through the VCR.
Due to copy guard protection, the picture may not be displayed properly. ??? Turn off all equipment before connection.
??? OPTICAL IN
??? After making the digital audio connection, make settings to suit the type of audio from your digital equipment. ( 25)
??? HDMI
The HDMI connection supports VIERA Link ???HDAVI Control??? ( 31) when used with a compatible Panasonic TV.
???Please use High Speed HDMI Cables that have the HDMI logo (as shown on the back cover). It is recommended that you use Panasonic???s HDMI cable. When outputting 1080p signal, please use HDMI cables 5.0 meters (16.4 ft.) or less.
B Video cable (not supplied)
AUX
VIDEO OUT
Connection for the better audio
OPTICAL
OUT
AUDIO IN
L
R
??? ???
To enjoy TV audio from this home theater system???s speakers:
1Connect the TV and the main unit with the Optical digital audio cable (not supplied).
2Select ???DIGITAL IN??? or
A Optical digital audio cable (not supplied)
B Video cable (not supplied)
VQT3D27
14
Connection for the best picture and audio
???When connecting to a TV using an HDMI cable, check the HDMI terminal on the TV. If the HDMI terminal is labeled ???HDMI (ARC)???, you can connect the unit simply with a single HDMI cable.
???It is possible to playback 3D videos and 3D still pictures by connecting this unit with a 3D compatible TV.
???For details, refer to the operating instructions of your TV.
??? When the HDMI terminal on the TV is labeled ???HDMI (ARC)???
Getting started
???
HDMI AV OUT (ARC)
To enjoy TV audio from this home theater system???s speakers:
Select ???ARC??? as a source (> 23).
A HDMI cable
[BTT770] [BTT370] [BTT270] : not supplied
[BTT273] : supplied
??? When the HDMI terminal on the TV is not labeled ???HDMI (ARC)???
VQT3D27
15
Connection with Set Top Box, etc.
??? [BTT770] [BTT370] When the connecting devices have an HDMI terminal
A HDMI cable (not supplied)
B Set Top Box (Cable/Satellite), etc.
COther devices (Video game, etc.)
???Make sure that the HDMI cable connection is made to enjoy the videos from the Set Top Box, etc. Futhermore, select ???HDMI Input1??? or ???HDMI Input2??? as a source.
???
A Refer to the operating instructions of the respective devices for the optimal connections.
B Optical digital audio cable (not supplied)
C Set Top Box (Cable/Satellite), etc.
OPTICAL
Radio antenna connection
??? Using an indoor antenna
???
FM ANT 75??
A FM indoor antenna (supplied)
BAdhesive tape
Affix this end of the antenna where reception is best.
VQT3D27
16
??? Using an outdoor antenna
Use outdoor antenna if FM radio reception is poor.
e.g., ???
Main unit
???
???
FM ANT 75??
AFM outdoor antenna [Using a TV antenna (not supplied)]
The antenna should be installed by a competent technician.
B 75 ??? coaxial cable (not supplied)
C Antenna plug (not supplied)
[BTT770] Digital transmitter connection
Do not insert or remove while the home theater unit is on.
Insert fully until you hear a click.
Make sure that the digital transmitter is fully inserted.
If the digital transmitter is not fully inserted, the sound may not be available from the surround speakers.
Getting started
Connection to a broadband network
The following services can be used when this unit is connected to broadband.
??? LAN cable connection
LAN 
??????
???
???
A LAN Cable (not supplied)
B Broadband router, etc.
C Modem (Broadband) *Provided by ISP
???Use category 5 or above straight LAN cables (STP) when connecting to peripheral devices.
???Inserting any cable other than a LAN cable in the LAN terminal can damage the unit.
??? Wireless LAN connection
???
???
???
???
A Main unit (Wireless LAN is built in.)
B Wireless router, etc.
C LAN Cable (not supplied)
D Modem (Broadband) *Provided by ISP
???For up to date compatibility information on your Wireless router refer to
http://panasonic.jp/support/global/cs/ (This site is in English only.)
???The unit is not compatible with public wireless LAN services provided in airports, stations, cafes etc. For additional information about this unit refer to
http://www.panasonic.com/consumer/support (For U.S.A.)
Precautions of Wireless LAN connection
The following limits are in place regarding the usage of this unit. You must be aware of these limits before using this unit.
Panasonic will in no way be responsible for any incidental damage which may arise due to a failure to obey these limits, or to any condition of use or disuse of this unit.
??? Data transmitted and received over radio waves may be intercepted and monitored. ??? This unit contains delicate electronic components.
Please use this unit in the manner in which it was intended and follow the following points:
??? Do not expose this unit to high temperatures or direct sunlight.
??? Do not bend, or subject this unit to strong impacts.
??? Keep this unit away from moisture.
??? Do not disassemble or alter this unit in any way.
VQT3D27
17
STEP 4: AC power supply cord connection
Connect only after all other connections are complete.
Main unit
???
???
AC IN
???
[BTT770]
Wireless System
???AC power supply cord with a ferrite core is for the wireless system. Do not use any other AC power supply cord except the supplied one.
A AC power supply cord (supplied)
B To a household AC outlet
Main unit
???
A AC power supply cord (supplied)
B To a household AC outlet
This unit consumes a small amount of AC power, even when it is turned off.
[BTT770] [BTT370] : approx. 0.05 W*, [BTT270] [BTT273]: approx. 0.4 W* * When the ???Quick Start??? setting is ???Off???
In the interest of power conservation, if you will not be using this unit for a long time, unplug it from the household AC outlet.
Wireless system [BTT770]: approx. 0.2 W
Install this unit so that the power cord can be unplugged from the socket outlet immediately if any problem occurs.
STEP 5: [BTT770] Preparing the wireless system
Turn on the wireless system after all connections are complete.
Press [POWER C I, B ??] on the wireless system.
POWER WIRELESS LINK
Unit on/off button [POWER C I, B ??]
C I: The wireless system is on.
B ??: The wireless system is off.
VQT3D27
18
STEP 6: Easy setup
The Easy setup assists you to make necessary settings.
Follow the
OK
Preparation
Turn on your TV and select the appropriate video input mode (e.g., VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this unit.
[BTT770] [BTT370]
??? Confirm the digital transmitter connection. (> 17)
1 Press [??].
Setup screen appears.
If this unit is connected to a Panasonic TV (VIERA) supporting HDAVI Control 2 or later via an HDMI cable, then setting information on the TV such as
2 Follow the
Language
Select the language used on menu screen.
TV Aspect
Select the aspect to suit your TV and preference.
[BTT770] [BTT370]
Wireless System
If a digital transmitter is inserted,
it is required to specify the current settings.
Speakers position
Specify the positioning of the surround speakers.
Speaker check
Check if the connection to each speaker is valid.
Speaker Output
Make surround sound setting for speaker output.
Cinema Surround Plus
(Effective when the surround layout is selected in ???Speakers position???.)
The function creates the sound of virtual speakers to enhance the realistic surround feeling as if the sound comes from all directions.
TV Audio
Select the audio input connection from your TV, [item with ???(TV)???].
Quick Start
Speed of startup from power off is increased.
[BTT770] [BTT370]
HDMI Standby
Even if this unit is in standby mode, a device connected with this unit can output videos and sound to the TV. (> 16, ???When the connecting devices have an HDMI terminal???)
3 Press [OK] several times to finish the ???Easy setup???.
After completing ???Easy setup???, you can perform ???Network Easy Setting???.
???You can perform this setup anytime by selecting ???Easy setup??? in the Setup menu. (> 40)
Getting started
VQT3D27
19
Network Easy Setting
The configuration of your network is about to begin. If you failed to make the settings, refer to page 21
Wired connection
Select ???Wired??? and press [OK].
Network Easy Setting
Select a connection mode.
Current setting : Wired
LAN cable connection:
Connect a LAN cable to the unit and select "Wired."
Wireless LAN connection:
Select "Wireless."
Wired
Wireless
OK
RETURN
Follow the
??? When you experience problems ( 21)
Wireless connection
Preparation
??? Obtain your network name ( 21, SSID).
???If your wireless connection is encrypted please be sure that you know your encryption key.
1 Select ???Wireless??? and press [OK].
2 Select ???Search for wireless network??? or ???WPS (PUSH button method)??? and press [OK] then follow the
Wireless Settings
Select a connection method.
Please refer to the operating instructions of your wireless access point about connection methods.
Search for wireless network
WPS (PUSH button method)
??? ???WPS (PUSH button method)???
If you are using a Wireless router that supports WPS
VQT3D27
??? ???Search for wireless network???
The available wireless networks will be displayed.
1Select your network name and press [OK].
???If your network name is not displayed search again by pressing the [R] button on the remote control. Stealth SSID will not be displayed, in this case enter manually.
Wireless Settings
Select a wireless network for connection.
Network name (SSID)Reception
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
When your wireless network is encrypted
2 Press [OK] to select ???Encryption Key???.
Wireless Settings
Enter the encryption key of the wireless network.
Encryption Key
Set
3 Enter your encryption key.
To enter SSID manually
If your SSID is not displayed in step 1, follow these steps.
Wireless Settings
Enter your network name (SSID) to connect.
SSID
Set
??? If your wireless network is encrypted, go to step 2.
20
When you experience problems with settings
Wireless Setting
Wireless Settings
Failed to complete.
A conflict with another device occurred.
Do you want to configure wireless network connection setting again ?
Network Easy Setting (Internet Connection Check)
Network Easy Setting (Internet Connection Check)
Complete.
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the owner's manual for the cause of the error and the solution for it.
Press [OK].
OK
Getting started
Network Easy Setting (Home Network Connection Check)
Network Easy Setting (Home Network Connection Check)
LAN cable is not connected.
Please check the connection.
Select ???Yes??? and press [OK] to check network connection again. Select ???No??? and press [OK] to finish Network Easy Setting.
???Refer to the operating instructions of the hub or router.
???WPS
???You can perform this setup anytime by selecting ???Network Easy Setting??? in
the Setup menu. ( 40)
??? You can redo these settings individually using ???Network Settings???. ( 40)
???Do not use this unit to connect to any wireless network for which you do not have usage rights.
During automatic searches in a wireless network environment, wireless networks (SSID*) for which you do not have usage rights may be displayed; however, using these networks may be regarded as illegal access.
???After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router.
???Please be aware that connecting to a network without encryption may result in the content of the communication being illegitimately viewed by a third party, or the leaking of data such as personal or secret information.
*An SSID (Service Set IDentification) is a name used by wireless LAN to identify a particular network. Transmission is possible if the SSID matches for both devices.
Reprogramming the remote control
If you have more than one Panasonic player/recorder and the remote control operates both products at once, you will
need to change the remote control code on one product to prevent this occurrence. ( 40, ???Remote Control Code???)
VQT3D27
21
Firmware updates
Occasionally, Panasonic may release updated firmware for this unit that may add or improve the way a feature operates. These updates are available free of charge.
This unit is capable of checking the firmware automatically when connected to the Internet via a broadband connection. When a new firmware version is available, the following message is displayed.
New firmware is available.
Please update firmware in Setup.
To update the firmware
Press [HOME] select ???Others??? [OK] [OK] (???Setup???)
DO NOT DISCONNECT the unit from the AC power or perform any operation while the update takes place.
After the firmware is installed, ???FINISH??? will be displayed on the unit???s display. Unit will restart and the following screen will be displayed.
The firmware was updated.
Current Version: x.xx
OK
RETURN
???If downloading on this unit fails or this unit is not connected to the Internet, then you can download the latest firmware from the following website and burn it to a
(This site is in English only.)
To show the firmware version on this unit. ( 40, ???System Information???)
???Downloading will require several minutes. It may take longer or may not work properly depending on the connection environment.
???If you do not want to check for the latest firmware version, set ???Automatic
Update Check??? to ???Off???. ( 40)
Inserting or removing media
OPEN/CLOSE VOL
SD CARD
???When inserting a media item, ensure that it is facing the right way up.
???While the reading indicator is displayed, do not turn off the unit or remove the media. Such action may result in loss of the media???s contents.
???When removing the SD card, press on the center of the card and pull it straight out.
???Selecting the source by the remote control
???Items to be displayed may vary with the media.
???When the selector is switched, it may take time to playback the selected video and/or audio.
*1 ???(TV)??? is displayed next to items set for TV AUDIO input.
*2 ???(CABLE/SATELLITE)??? is displayed next to DIGITAL IN when set for CABLE/SATELLITE AUDIO input.
VQT3D27
22
HOME menu
Major functions of this unit can be operated from the HOME menu.
Preparation
Turn on the television and select the appropriate video input on the television.
???When a media is inserted, contents selection screen for that media is displayed.
???If there are any other items, repeat this step.
???To return to HOME menu, select ???HOME??? or press [RETURN] several times.
???Items to be displayed may vary with the media.
???When the selector is switched, it may take time to playback the selected video and/or audio.
*1 ???(TV)??? is displayed next to items set for TV AUDIO input.
*2 ???(CABLE/SATELLITE)??? is displayed next to DIGITAL IN when set for CABLE/SATELLITE AUDIO input.
VQT3D27
23
Enjoying sound effects from all speakers
Enjoying surround sound effects
1 Press [SURROUND] several times to select the effect.
STANDARD
Sound is output as it was recorded/encoded.
Speaker output varies depending on the source.
You can enjoy sound from the front speakers, as well as the surround even when playing a
MANUAL
???The selected effect will only be displayed on the main unit.
2 While ???MANUAL??? is displayed, press [2, 1] and select the desired effect.
DOLBY PRO LOGIC II MOVIE
Suitable for movie software, or the one recorded in Dolby Surround.
DOLBY PRO LOGIC II MUSIC
Adds
7.1CH VIRTUAL SURROUND
You can enjoy
SUPER SURROUND
You can enjoy sound from all speakers with stereo sources.
2CH STEREO
You can play any source in stereo. Sound will be output to the front speakers and the subwoofer only.
???When you set to ???7.1CH VIRTUAL SURROUND???, ???SUPER SURROUND??? and ???2CH STEREO???, ???Cinema
Surround Plus??? ( 36) is not activated.
??? Adjusting speaker level during play
1 Press and hold [jCH SELECT] to activate the speaker setting mode.
2Press [jCH SELECT] several times to select the speaker. Each time you press the button:
L R?????? C?????? RS??????RB*?????? LB*??????LS?????? SW
???????????????????????????????????????????????????????????????????????????????????????????????????????????????
* When the optional surround back speakers are connected.
???The channels not included in the playing audio will not be displayed (subwoofer is displayed even if it is not included).
3Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker.
s6 dB to r6 dB
??? Changing the sound modes
1Press [SOUND] several times to select the mode.
???The selected mode will only be displayed on the main unit.
2While the selected mode is displayed Press [2, 1] and select the desired setting.
EQUALIZER
You can select sound quality settings.
FLAT
Cancel (no effect is added).
HEAVY
Adds punch to rock.
CLEAR
Clarifies higher sounds.
SOFT
For background music.
SUBWOOFER LEVEL
You can adjust the amount of bass.
1 (Weakest effect) to 4 (Strongest effect)
???The setting you make is retained, and recalled every time you play the same type of source.
H.BASS
You can enhance
???The setting you make is retained, and recalled every time you play from the same type of source.
CENTER FOCUS
(Effective when playing audio containing center channel sound.)
You can make the sound of the center speaker seem like it is coming from within the TV.
You can enhance the surround effect for low volume sound. (Convenient for late night viewing.)
???The sound effects/modes may not be available or have no effect with some sources.
???You may experience a reduction in sound quality when these sound effects/modes are used with some sources. If this occurs, turn the sound effects/modes off.
24
Playing video contents
[BD] [DVD] [CD] [SD]
1 Insert the media.
If the menu is displayed, press [OK] or [3, 4, 2, 1] to select the item. ( 23)
2 Press [3, 4] to select the title and press [OK].
When a message screen is displayed while playing back 3D compatible video software, play back in accordance with the instructions.
??? To show menus
You can show Top Menu, DIRECT NAVIGATOR or
Press
??? Press [3, 4, 2, 1] to select the item and press [OK].
??? To show the status messages
While playing, press [STATUS].
The status messages give you information about what is currently being played. Each time you press [STATUS], the display information may change or will disappear from the screen.
e.g.
T: Title, C: Chapter, PL: Playlist
Elapsed time in the title
???DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. Press [???STOP] when you finish to preserve the unit???s motor and your television screen.
???Depending on media and contents, the display may change or may not appear.
???It is not possible to playback AVCHD and MPEG2 video which have been dragged and dropped, copied and pasted to the media.
Other operations during play
These functions may not work depending on the media and its contents.
Stop
Press [???STOP].
The stopped position is memorized.
Resume play function
Press [1 PLAY] to restart from this position.
???The position is cleared if the tray is opened or you press [???STOP] several times to display ???STOP??? on the unit???s display.
???On
Pause
Press [;PAUSE].
??? Press [;PAUSE] again or [1 PLAY] to restart play.
Skip
While playing or paused, press [:] or [9].
Skip to the title, chapter or track you want to play. ??? Each press increases the number of skips.
While paused, press [2] (2;) or [1] (;1).
???Press and hold to change in succession forward or backward.
???Press [1 PLAY] to revert to normal playback speed.
???
Changing audio
1 Press and hold [jAUDIO] to activate the audio setting mode.
2 Press [jAUDIO] several times to select the audio.
You can change the audio channel number or soundtrack language, etc.
??? Selecting the type of audio from the DIGITAL AUDIO IN terminal
Select to suit the type of audio from the DIGITAL IN terminal on the main unit.
1 Press
3Press [jAUDIO] several times to select the type.
MAIN SAP*
MAINrSAP* (stereo audio)
* ???SAP??? = Secondary Audio Program (Only works with Dolby Dual Mono)
??? ???MAIN??? or ???SAP??? is not available if ???On??? is selected in
???Audio that is input through the DIGITAL AUDIO IN or AUX terminals are not output from the HDMI AV OUT terminal.
VQT3D27
25
Useful functions
1 Press [SUB MENU].
2 Select an item and press [OK].
While DIRECT NAVIGATOR screen is displayed
???Depending on the played contents if you perform ???Screen Aspect???, there may be no effect.
??? When ???TV Aspect??? ( 39) is set to ???4:3??? or ???4:3 Letterbox???, the ???Zoom??? effect in ???Screen Aspect??? is disabled.
??? Depending on the media and contents, displayed items are different.
Enjoying
Enjoying
Internet
???This unit is using an SD card as a local storage device.
1 Perform network connection and settings. ( 17, 20)
2 Insert an SD card with 1 GB or more free space.
3 Insert the disc.
VQT3D27
??? Deleting data/Formatting SD cards
If you no longer need data recorded on the SD card, you can delete data with the following operation.
1 Insert an SD card.
2 Press [HOME].
3 Press [3, 4, 2, 1] to select ???Others??? and press [OK].
4Press [1] to select ???SD Card Management??? and press [OK].
5Press [3, 4] to select
Format SD Card
RETURN
6 Press [2, 1] to select ???Yes??? and press [OK]. 7 Press [2, 1] to select ???Start??? and press [OK].
Playing
To turn on/off secondary video and audio
[DISPLAY] select ???Disc??? [1] select ???Signal Type??? [OK] set ???Video??? and ???Soundtrack??? in ???Secondary Video??? to ???On??? or ???Off???
???
???
A Secondary video
B Primary video
???The usable functions and the operating method may vary with each disc, please refer to the instructions on the disc and/or visit their website.
???Some
???To use the
???
( 37).
???When discs supporting
???During
???When
secondary audio will not be played ( 38).
26
Enjoying 3D video
You can enjoy powerful 3D videos with realistic sensations by connecting this unit with a High Speed HDMI Cable to a 3D compatible TV.
The illustration is an image.
Preparation
Connect 3D compatible TV to an HDMI AV OUT terminal of this unit using a High Speed HDMI Cable and select HDMI video input mode on the TV. ( 14, 15)
??? Perform the necessary preparations for the TV.
Method of playback is the same as normal disc playback. ( 25)
??? Playback following the instructions displayed on the screen.
3D settings
Perform the following settings as necessary.
Useful functions
1 While playing,
Press [SUB MENU].
2 Press [3, 4] to select ???3D Settings??? and press [OK].
3 Select an item, then press [OK].
???Depending on the contents, displayed items are different.
???Please refrain from viewing 3D images if you do not feel well or are experiencing visual fatigue.
In the event that you experience dizziness, nausea, or other discomfort while viewing 3D images, discontinue use and rest your eyes.
???Depending on the connected TV, the video being played back might switch to 2D video due to changes in resolution etc. Check the 3D setting on the TV.
???3D images may not output as settings of ???HDMI Resolution??? and ???24p Output???. ( 39)
VQT3D27
27
Playing still pictures
Useful functions
[BD] [DVD] [CD] [SD]
In order to play back 3D still pictures (MPO), this unit should be connected to a Full HD 3D compatible TV via an HDMI terminal.
1 Insert the media.
If the menu is displayed, press [OK] or [3, 4, 2, 1] to select the item. ( 23)
2 Press [3, 4] to select the folder and press [OK].
???3D View??? : 3D still pictures (MPO) are sorted here. To play back in 3D, select from ???3D View???. (Still pictures in ???2D View??? are played back in 2D)
Photo View
SD card
To select folders or still pictures that are played on slideshow.
3 Press [3, 4, 2, 1] to select the still picture and press [OK].
Press [2, 1] to display the previous or next still picture.
To exit the screen
Press [RETURN].
??? To show the still picture properties
While playing, press [STATUS] once or twice.
1 / 26
Manufacturer
Equipment
To exit the screen
Press [STATUS].
1 Press [SUB MENU].
2 Select an item, then press [OK].
While Photo View screen is displayed
???Depending on the condition of the unit and media contents, displayed items are different.
???When viewing a 3D still picture, some functions may not work.
???When a still picture with large number of pixels is played, the display interval may become longer. Even if the setting is changed, the display interval may not become shorter.
???When both a music CD and an iPod/iPhone is inserted to this unit, the iPod/iPhone has a priority to be played back as background music.
???Still pictures displayed as ??? 
??? cannot be played back with this unit.
VQT3D27
28
Playback
Radio
1 While the DIRECT NAVIGATOR screen is displayed
Press [SUB MENU].
2 Press [3, 4] to select ???Select Folder??? and press [OK].
??? You cannot select folders that contain no compatible tracks.
Presetting stations manually
Preparation
Select a radio broadcast.
1 Press [RADIO] to select ???FM???.
2 Press [SEARCH6] or [SEARCH5] to select the frequency.
???To start automatic tuning, press and hold [SEARCH6], [SEARCH5] until the frequency starts scrolling. Tuning stops when a station is found.
1 While listening to the radio broadcast
Press [OK].
2 While ???P??? is flashing on the display
Press the number buttons to select a channel.
To select a
To select a
???A station previously stored is overwritten when another station is stored in the same channel preset.
VQT3D27
29
1
2 Press the number buttons to select the channel.
To select a
To select a
Alternatively, press [W, X] or [3, 4].
??? Display on the main unit
TUNED/STEREO:
Displayed when receiving stereo broadcasting
TUNED:
Displayed when receiving monaural broadcasting or monaural sound is selected.
??? If noise is excessive
1 Press and hold [jAUDIO] to activate to select the type. 2 Press [jAUDIO] to display ???MONO???.
The sound becomes monaural.
Press the button again in step 2 to cancel the mode. ???AUTO STEREO??? will be displayed on the main unit. Depending on the broadcast system, stereo or monaural will be selected. ???MONO??? is also canceled when you change the frequency.
??? This setting can be preset for each broadcasting station.
??? FM frequency step
Main unit:
The factory setting is set to 0.2 MHz, it can be changed to receive broadcasts allocated in 0.1 MHz. You may need to change this setting if the tuner seems to skip over the correct frequency for stations in your area.
1 Press [RADIO] to select ???FM???.
2Press and hold [RADIO].
After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest frequency changes and the step is changed.
To return to the original settings, repeat steps 1 and 2.
???After changing the setting, previously preset frequencies will be cleared. Preset them again.
VQT3D27
Enjoying TV with unit???s speakers
Preparation
Turn on your TV and select the appropriate audio input mode [AUX, ARC,
Surround sound effects
You can enhance stereo sources with surround sound effect.
1 Press [SURROUND] several times to select the effect.
2 While ???MANUAL??? is displayed on the unit???s display
Press [2, 1] and select the desired effect.
Surround modes to enjoy TV audio or stereo sources from all speakers:
???DOLBY PRO LOGIC II MOVIE
???DOLBY PRO LOGIC II MUSIC
???SUPER SURROUND
For more detailed information on this operation, please refer to the ???Enjoying surround sound effects??? section on page 24.
Sound modes
You can adjust the mode depending on the source or situation.
1 Press [SOUND] several times to select the mode.
2 While the selected mode is displayed on the unit???s display
Press [2, 1] and select the desired setting.
For more detailed information on this operation, please refer to the ???Changing the sound modes??? section on page 24.
30
Linked operations with
the TV (VIERA LinkTM ???HDAVI
ControlTM???)
What is VIERA Link ???HDAVI Control????
VIERA LinkTM is a new name for EZ SyncTM.
VIERA Link ???HDAVI Control??? is a convenient function that offers linked operations of this unit, and a Panasonic TV (VIERA) under ???HDAVI Control???.
You can use this function by connecting the equipment with an HDMI cable. See the operating instructions for connected equipment for operational details.
Preparation
1 Set ???VIERA Link??? to ???On??? ( 39). (The default setting is ???On???.)
2Set the ???HDAVI Control??? operations on the connected equipment (e.g., TV).
3Turn on all ???HDAVI Control??? compatible equipment and select this unit???s input channel on the connected TV so that the ???HDAVI Control??? function works properly.
When the connection or settings are changed, repeat this procedure.
Setting the audio link
??? Setting the audio link with the TV
With the remote control:
??? Select the actual TV audio connection on the main unit. 1 Press [HOME].
2 Press [3, 4, 2, 1] to select ???Others??? and press [OK]. 3 Press [OK] to select ???Setup???.
4 Press [3, 4] to select ???TV / Device Connection???. 5 Press [3, 4] to select ???TV Audio Input???.
6Press [2, 1] to switch ???AUX???, ???ARC??? or ???DIGITAL IN??? and press [OK].
???Select ???AUX??? or ???ARC???*1 in ???TV Audio Input??? when the
DIGITAL AUDIO IN terminal is used for the STB connection.
Whenever the connection or settings are changed, reconfirm the points above.
??? Setting the audio link with the STB
With the remote control:
???Select the STB input channel on the TV. 1 Press
2 Press [STATUS] to select ???CABLE/SATELLITE AUDIO ON???.
???If the input channel of the STB on the TV is changed or if you want to change the device allocated for the linked operations, select ???CABLE/SATELLITE AUDIO OFF??? in step 2 above and then repeat steps 1 to 2.
???If using ???HDMI IN1??? or ???HDMI IN2??? as a source, set to ???CABLE/SATELLITE AUDIO OFF??? in step 2.
???VIERA Link ???HDAVI Control???, based on the control functions provided by HDMI which is an industry standard known as HDMI CEC (Consumer Electronics Control), is a unique function that we have developed and added. As such, its operation with other manufacturers??? equipment that supports HDMI CEC cannot be guaranteed.
???This unit supports ???HDAVI Control 5??? function.
???HDAVI Control 5??? is the newest standard (current as of December, 2010) for Panasonic???s HDAVI Control compatible equipment. This standard is compatible with Panasonic???s conventional HDAVI equipment.
???Please refer to individual manuals for other manufacturers??? equipment supporting VIERA Link function.
Speaker control
You can select whether audio is output from the unit???s speakers or the TV speakers by using the TV menu settings.
Home theater
TV
???The volume of this unit is set to ???0???.
???Audio output is
???When switching between this unit???s speakers and TV speakers, the TV
screen may be blank for several seconds.
???The audio from ???AUX???, ???DIGITAL IN???, ???FM Radio??? or ???iPod??? will be output from this unit's speakers even though the TV speakers are selected.
Automatic input switching (Power on link)
When the following operations are performed, the television will automatically switch the input channel and display the corresponding action. When the TV is off, the TV will automatically turn on.
jWhen play starts on the unit
jWhen an action that uses the display screen is performed (e.g., DIRECT NAVIGATOR screen)
???When you switch the TV input to TV tuner mode, this unit will automatically switch to ???AUX???*2, ???ARC???*1,*2 or
???This function does not work when the iPod/iPhone selector is chosen. ( 33)
VQT3D27
31
Automatic
Delay between audio and video is automatically adjusted, enabling you to enjoy smooth audio for the picture ( 38, ???Audio Delay???).
???This function works only when ???BD/DVD???, ???SD???, ???AUX???*2, ???ARC???*1,*2,
*1 The selection works only when using an ARC compatible TV.
*2 ???AUX???, ???ARC??? or
Power off link
All connected equipment compatible with ???HDAVI Control???, including this unit, automatically turns off when you switch the television off.
Playing music continuously even after turning off the TV
(When the unit is connected to a Panasonic TV (VIERA) that supports HDAVI Control 2 or later.)
Select ???Video??? in ???Power Off Link??? ( 39)
Easy control only with VIERA remote control
Only TV supports ???HDAVI Control 2??? or later
By using the TV remote control, you can play discs using the ???Control Panel??? and display the Top Menu or
???This works only during ???BD/DVD??? or ???SD??? playback and resume modes.
1 Press [SUB MENU].
e.g.
Control Panel
Screen Aspect
Top Menu
2 Select an item, then press [OK].
???The sub menu may not appear while the Top Menu for
???The buttons that you can use for this unit can vary depending on the TV.
For details, refer to the operating instructions of the TV.
???The operation of this unit may be interrupted when you press incompatible buttons on the TV remote control.
???Depending on the menu, some button operations cannot be performed from the TV???s remote control.
Using the iPod/iPhone
Compatible iPod/iPhone (as of December 2010)
???Update your iPod/iPhone with the latest software before using this unit.
???Compatibility depends on the software version of your iPod/iPhone.
???iPod/iPhone compatibility assures music, video playback and battery charge functions of this unit as a home theater system.
* Playback functions on the main unit may be limited in the ???All??? mode.
In some locations, reception status of an iPhone may be poor when it is loaded on this unit.
???When the iPhone receives a call while connected to this unit, playback, etc. of the iPhone may stop.
To prioritize the operation with the iPhone connected to this unit, make the setting so that the iPhone does not receive calls.
iPod/iPhone Connection
Preparation
???Before connecting/disconnecting the iPod/iPhone, turn the main unit off or reduce the volume of the main unit to its minimum.
???Make sure that the video cable connection is made to view photos/videos from the iPod/iPhone.
1 Push the center of drawer (A), and pull out fully until it clicks to open the Dock for iPod/iPhone (C).
2 Install a Dock adapter (not supplied) (B) before inserting your iPod/iPhone into the dock.
3 Connect the iPod/iPhone (not supplied) firmly.
VQT3D27
32
iPod/iPhone
3
2 ???
???
???
Main unit
A The center of drawer
BDock adapter (not supplied)
???Please be sure to use the adapter that is compatible with your model of iPod/iPhone.
???Attach the dock adapter until it is firmly in place.
???To purchase a dock adapter, consult your local iPod/ iPhone dealer.
C Dock for iPod/iPhone
DMake sure to match when inserting.
???Carefully insert and remove the iPod/iPhone to ensure long lasting product enjoyment.
???Check that the connector has no dust or foreign materials before connecting.
???The 3D logo on the Dock for iPod/iPhone does not mean that the iPod/ iPhone has 3D capabilities.
???Avoid using
About recharging the battery
???iPod/iPhone will start recharging regardless of whether this unit is on or off.
??????IPOD ????? will be shown on the main unit???s display during iPod/iPhone charging in main unit standby mode.
???Once fully recharged, additional recharging will not occur.
iPod/iPhone Playback
Preparation
???Make sure that the ???IPOD??? source is selected. Press [iPod] to select the source.
???To view photos/videos from the iPod/iPhone
Operate the iPod/iPhone menu to make the appropriate photo/video output settings for your TV.
???To display the picture, turn on the TV and select the appropriate video input mode.
Enjoy music/video
1 Press [iPod] to select ???IPOD???.
2 Press [STATUS] several times to select the music menu or videos menu.
???You can also select "Videos" or "Music" by using HOME menu. (> 23)
3 Press [3, 4] to select an item and press [OK].
???Repeat this step until the selected title starts playback.
???Press [2, 1] to display the previous or next page. e.g., music playback screen
iPod
VQT3D27
33
Images are for illustration purposes, contents may change without notice.
To exit from VIERA CAST
Press [EXIT] or [HOME].
VQT3D27
34
???When playing content from a disc/SD card VIERA CAST cannot be accessed by pressing [VIERA CAST].
???In the following cases, settings are possible using ???Internet Content
Settings??? ( 40)
???When restricting the use of VIERA CAST.
???When the audio is distorted.
???When wrong time is displayed
???If using slow Internet connection, the video may not be displayed correctly. A
???Be sure to update the firmware when a firmware update notice is displayed on the screen. If the firmware is not updated, you will not be able to use the
VIERA CAST function. ( 22)
???VIERA CASTTM home screen is subject to change without notice.
???The services through VIERA CASTTM are operated by their respective service providers, and service may be discontinued either temporarily or permanently without notice. Therefore, Panasonic will make no warranty for the content or the continuity of the services.
???All features of websites or content of the service may not be available.
???Some content may be inappropriate for some viewers.
???Some content may only be available for specific countries and may be presented in specific languages.
Playback menu
1 Press [DISPLAY].
e.g.,
Video
The recording method of original video appears.
Advanced operations Other devices
Soundtrack
Show or change the soundtrack.
Subtitle
Turn the subtitle on/off, and change the language depending on the media.
Subtitle Style
Select the subtitle style.
Audio channel
Select the audio channel number. ( 25, ???Changing audio???)
Angle
Select the number of the angle.
Play
Repeat Play
(Only when the elapsed time is being displayed on the unit???s display.)
Select the item which you want to repeat. The items displayed differ depending on the type of media.
Select ???Off??? to cancel.
Random
Select whether or not to play random.
[Only when ???Full HD??? is selected in ???3D Type??? ( 39).]
Video
Picture
Select the picture quality mode during play.
Advanced Setting
Chroma Process
The
Detail Clarity
The picture is sharp and detailed.
Super Resolution
Pictures of normal image quality are corrected to sharp and detailed images when output as 1080i/1080p from HDMI AV OUT.
Progressive
Select the method of conversion for progressive output to suit the type of material being played.
???When the content is distorted change the settings from ???Auto??? to ???Video???.
24p
Movies and other material recorded on
??? Only when you have selected ???On??? in ???24p Output??? ( 39)
VQT3D27
36
Audio
Movie Sound Effect
Select the sound effect of the movie.
???Cinema Surround Plus:
The function creates the sound of virtual speakers to enhance the realistic surround feeling as if the sound comes from all directions.
Music Sound Effects*1, *2
Select the sound effect of the music.
???Digital Tube Sound:
This feature gives you warm sound, like that produced by a vacuum tube amplifier.
???
This feature gives you brighter sound by increasing the high frequency portion of the audio. (Discs recorded at 48 kHz or less)
Recommended settings:
High Clarity Sound
When connected to TV via the HDMI AV OUT terminal for outputting image, it produces clearer sound.
???Only when you have selected ???Enable??? in ???High Clarity Sound??? ( 38).
Setup menu
Change the unit???s settings if necessary. The settings remain intact even if you switch the unit to standby.
1 Press [HOME].
2 Press [3, 4, 2, 1] to select ???Others??? and press [OK].
3 Press [OK] to select ???Setup???.
Setup
Disc
Video
Audio
Display
TV / Device Connection
Network
Others
OK
RETURN
4 Press [3, 4] to select the menu and press [OK].
5 Press [3, 4] to select the item and press [OK].
If there are any other items, repeat these steps.
6 Press [3, 4, 2, 1] to select the option and press [OK].
???There may be differences in operation methods. If this happens, follow the
About the password
The following items use the same password.
Don???t forget your password.
???
???
??????Lock??? (> 40)
Disc
Set a ratings level to limit
???Follow the
Set an age limit of
???Follow the
3D
Select the playback method of 3D compatible video software.
Audio Language
Choose the language for audio.
???If ???Original??? is selected, the original language of each disc will be selected.
???Enter a code (> 46) with the number buttons when you select ???Other ???????????.
Subtitle Language
Choose the language for the subtitle.
???If ???Automatic??? is selected and the language selected for ???Audio Language??? is not available, subtitles of that language will automatically appear if available on that disc.
???Enter a code (> 46) with the number buttons when you select ???Other ???????????.
Menu Language
Choose the language for the disc menus.
???Enter a code (> 46) with the number buttons when you select ???Other ???????????.
VQT3D27
37
Video
Still Mode (paused video)
Select the type of picture shown when you pause playback.
Seamless Play
The chapter segments in playlists are played seamlessly.
???Select ???On???, when the picture freezes for a moment at the chapters segment in playlists.
Black Level Control
Select lighter or darker for adjusting the black level control to the desired setting for picture enhancement.
Audio
Dynamic Range Compression
You can listen at low volumes but still hear dialog clearly. (Dolby Digital, Dolby Digital Plus and Dolby TrueHD only) ??? ???Auto??? is effective only when playing Dolby TrueHD.
Digital Audio Output
Press [OK] to show the following settings:
Dolby D/Dolby D +/Dolby TrueHD
Select the audio signal to output.
???Select ???PCM???, when the connected equipment cannot decode the respective audio format.
???Not making the proper settings may result in noise.
Select whether to mix or not mix the primary audio and secondary audio (including the button click sound). (> 26)
???If ???Off??? is selected, the unit outputs the primary audio only.
Downmix
Select the downmix system to enjoy
???Select ???Surround encoded??? to enjoy the surround sound.
???There is no downmix effect on the bitstream audio signal.
???The audio will be output in ???Stereo??? in the following cases:
???AVCHD playback
???Dolby TrueHD playback
???Playback of secondary audio (including the button click sound).
High Clarity Sound
When connected to TV via the HDMI AV OUT terminal for outputting image, it produces clearer sound.
???Set to ???Enable??? and then set ???High Clarity Sound??? on the Playback menu to ???On???. (> 36)
Audio Delay
Speaker
Refer to page 41
Display
Status Messages
Choose whether to show status messages automatically.
Choose the language for menus and
Screen Saver Function
This is to prevent
???When this is set to ???On???:
If there is no operation for 5 minutes or more, DIRECT NAVIGATOR screen switches to HOME menu automatically.
???While playing and pausing, etc., this function is not available.
???While playing music
Front Panel Display
Changes the brightness of the unit???s display.
???If ???Auto??? is selected, the display is dimmed but brightens when you perform some operations.
Digital Audio Input
Press [OK] to show the following settings:
Select the following audio signal to input. jARC
jDIGITAL IN
j[BTT770] [BTT370] HDMI Input1 j[BTT770] [BTT370] HDMI Input2
??????On???: PCM is available.
??????Off???: DTS, PCM and Dolby Digital are available. Select ???On??? if the sound is cut off intermittently.
VQT3D27
License
Information about the software used by this unit is displayed.
38
TV / Device Connection
3D Settings
Press [OK] to show the following settings
3D Type
Select the format of the connected TV.
???Change the settings for 3D on the TV also when ???Checker board??? or ???Side by side??? is selected.
3D Playback Precautions
Set to display or hide the 3D viewing warning screen when playing back the 3D compatible video software.
TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television and playing 16:9 ratio image:
When connected to a 16:9 widescreen television and playing 4:3 ratio image:
HDMI Connection
Press [OK] to show the following settings:
HDMI Resolution
The items supported by the connected devices are indicated on the screen as ????????. When any item without ???????? is selected, the images may be distorted.
???If ???Auto??? is selected, automatically selects the output resolution best suited to the connected television.
???To enjoy
24p Output
When this unit is connected to a TV supporting 1080/24p output using an HDMI cable, movies and other material recorded at 24p are output at 24p.
??? When playing
???When
???24p :
A progressive image recorded at a rate of 24 frames per second
HDMI Color Mode
This setting is for selecting
HDMI Audio Output
This setting selects whether or not to output audio from HDMI.
???Audio will be output through the system's speakers when "Off" is selected.
[BTT770] [BTT370]
HDMI Standby
Even if this unit is in standby mode, a device connected with this unit can output videos and sound to the TV. Moreover, you can switch the HDMI input terminal by pressing
??? Sound will not be output from this unit's speakers.
VIERA Link
Set to use ???HDAVI Control??? function when connected with an HDMI cable to a device that supports ???HDAVI Control???.
???Select ???Off??? when you do not want to use ???HDAVI Control???.
Deep Color Output
This setting is for selecting whether to use Deep Color output when a television that supports Deep Color is connected.
Contents Type Flag
Depending on the playback content, the TV will output adjusting to the optimal method when a TV that supports this function is connected.
When the TV is turned off, this unit will turn off except during the following conditions:
jCD or MP3 audio playback
jiPod/iPhone mode jRadio mode
j???AUX???,???ARC??? or
TV Audio Input
Select the TV audio input to work with the VIERA Link operations.
VQT3D27
39
Network
Network Easy Setting (> 20)
Network Settings
Perform
Press [OK] to show the following settings:
LAN Connection Mode
Select connection method.
Wireless Settings
This allows the Wireless router and connection settings to be set and the current connection settings and connection state to be checked when a wireless connection is used.
Connection Setting
The Wireless router connection wizard will be displayed.
IP Address / DNS Settings
This is for checking the state of the network connection and setting the IP address and
Press [OK] to show the respective setting.
??????Connection Speed Setting??? is enabled only when ???Auto Detect Connection Speed??? is turned ???Off???.
Proxy Server Settings
This is for checking the state of connection with the Proxy server and performing settings.
Press [OK] to show the respective setting.
Internet Content Settings (> 34) (VIERA CAST)
Press [OK] to show the following settings:
Lock
You can restrict the usage of VIERA CAST. ???Follow the
password with the number buttons when the password screen is shown.
Audio Auto Gain Control
Volume that is different depending on the contents is adjusted automatically to the standard volume while using the VIERA CAST.
???Depending on contents, this function effect will not work.
???Select ???Off??? when the audio is warped.
Time Zone
By selecting the time zone, it is possible to set the unit???s time to match your location.
???Some VIERA CAST contents require the time zone to be set. Set the time zone if necessary.
DST
Select ???On??? when using Daylight Saving time.
MAC Address
Displays the MAC address of this unit.
Others
Remote Control Code
Change the remote control code, when other Panasonic products react to this remote control.
Quick Start*
Speed of startup from power off is increased.
???Internal control unit will be powered when it is set to ???On???, so contents of the following will be different from the time it is set to ???Off???.
???Idle power consumption will increase. (More about the power consumption > 48)
*Depending on the power conserving setting activated on the TV, this function may have less effect when the unit is started by the power on link function. (> 31)
Easy setup (> 19)
You can execute basic settings to optimize your home theater system.
Restore Default Settings
This returns all values in the Setup menu and the Playback menu, except for ???Remote Control Code???, ???LAN Connection Mode???, ???Wireless Settings???, ???IP Address / DNS Settings???, ???Proxy Server Settings???, ???Lock???,
System Information
Display firmware version of this unit and wireless LAN module.
Firmware Update (> 22)
Press [OK] to show the following settings:
Automatic Update Check
When this equipment remains connected to the Internet, it will check for the latest firmware version when it is turned on and you can update it if necessary.
Update Now
You can update the firmware manually.
VQT3D27
40
Speaker settings
Delay time
For optimum listening with
If either distance A or B is less than C, find the difference in the relevant table and adjust the delay time to make up for the difference.
B Surround speaker / Surround back speaker
[BTT770] [BTT370]
??? When using the 7.1ch speaker system
1Check the distance difference of both the front speakers and the surround back speakers from the seating position.
2 Set the delay time of the surround back speakers.
Adjusting speaker level
VQT3D27
41
Speaker installation option
Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
???The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg (22 lbs) per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers.
???Do not attempt to attach these speakers to walls using methods other than those described in this manual.
F 28.5 mm (1 1/8q) G 97 mm (3 13/16q) H 335 mm (13 3/16q)
I210 mm to 212 mm (8 9/32q to 8 11/32q)
J 40 mm (1 9/16q) K 63 mm (2 15/32q) L 322 mm (12 11/16q) M 40 mm (1 9/16q) N 17.6 mm (11/16q) O 98.7 mm (3 7/8q)
[BTT770]
Center speaker
[BTT770] [BTT370] [BTT273]
Surround speaker
[BTT270]
Front speaker, Surround speaker
??? ???
???
???
1 Drive a screw (not supplied) into the wall.
A At least 30 mm (1 3/16q) B ??? 4.0 mm (5/32q)
C ??? 7.0 mm to ??? 9.4 mm (9/32q to 3/8q)
D Wall or pillar
E5.5 mm to 7.5 mm (7/32q to 5/16q)
2 Fit the speaker securely onto the screw(s) with the hole(s).
e.g., [BTT770] Front speaker
Use the measurements indicated below to identify the screwing positions on the wall.
???Leave at least 20 mm (25/32q) of space above the speaker and 10 mm (13/32q) on each side to allow enough space for fitting the speaker.
[BTT770] [BTT370] [BTT273]
Front speaker
Attach to a wall without the base and the stand.
42
[BTT770] [BTT370] [BTT273]
??? To avoid speaker dropping
Front speaker, Center speaker e.g., [BTT770] Front speaker
??? Consult a qualified building contractor to avoid damage to the wall or speakers.
??? Use a string of less than ??? 2.0 mm (3/32q), which is capable of supporting over 10 kg (22 lbs).
Troubleshooting guide
Before requesting service, please perform the following steps.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating irregularities that are discovered with certain movies. (> 22)
4
Make the following checks and visit our website for more information.
For U.S.A. :
http://www.panasonic.com/help
Enter the model number.
For Canada :
http://www.panasonic.ca
4
Or visit our website to find a service center.
You can find a service center near you easily on our website.
Other support information:
???Customer Services Directory (United States and Puerto Rico)??? (> 50) or ???Limited Warranty (Only for CANADA)??? (> 51)
The following do not indicate a problem with this unit: jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
??? Unit does not respond to the remote control or front panel buttons.
Press and hold [POWER ??/I] on the main unit for 5 seconds. jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
??? Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote control and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds.
General operation
To return to the factory preset
???Select ???Yes??? in ???Restore Default Settings??? in the Setup menu. (> 40)
To return all settings to the factory preset
???Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/ CLOSE] and [POWER ??/I] on the main unit at the same time for more than 5 seconds.
The remote control doesn???t work properly.
???Change the batteries in the remote control. (> 9)
???The remote control and main unit are using different codes. If ???SET ?????? is displayed on the unit???s display when a button is pressed on the remote control, change the code on the remote control. (> 40)
Disc cannot be played.
???The disc is dirty. (> 9)
???Check the region code.
Still pictures (JPEG) do not playback normally.
???The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.
The TV tuner mode is not displayed when the TV is switched on.
???This phenomenon may occur, depending on the TV setting, when ???Quick Start??? is set to ???On???.
???Depending on the TV, this phenomenon may be prevented by reconnecting the HDMI cable to a different HDMI input terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
The ratings level returns to the factory preset.
1While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. j???00 RET??? is displayed on the unit???s display.
2Repeatedly press [1] (right) on the remote control or [POWER ??/I] on the unit until ???03 VL??? is displayed on the unit???s display.
3Press [OK] on the remote control or [< OPEN/CLOSE] on the unit.
This unit does not recognize the communication camera correctly.
???Disconnect and reconnect the communication camera. If it still does not recognize the connection, turn the power of this unit off and on again.
Power
No power.
???Insert the AC power supply cord securely into a household AC outlet. (> 18)
The unit switches to standby mode.
???This unit will automatically turn to standby mode after 30 minutes if it is inactive. (> 7)
???When the time set for the sleep timer has passed, the power will be turned off. (> 6)
???One of the unit???s safety devices is activated. Press [POWER ??/I] on the main unit to turn the unit on.
The unit does not turn off.
1Press and hold [POWER ??/I] on the main unit for 5 seconds. (If still unable to power the unit off, disconnect the power
Displays
The images from this unit do not appear on the TV. Picture is distorted.
Jittering occurs.
???An incorrect resolution is selected in ???HDMI Resolution???. Reset the setting as follows:
1While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds. j???00 RET??? is displayed on the unit???s display.
2Repeatedly press [1] (right) on the remote control or [POWER ??/I] on the unit until ???04 PRG??? is displayed on the unit???s display.
3Press and hold [OK] on the remote control or [< OPEN/ CLOSE] on the unit for at least 3 seconds.
Set the item again. ( 39)
jWhen Dolby Digital Plus, Dolby TrueHD, and
???When ???3D
Video is not output.
??? Set ???High Clarity Sound??? in the Playback menu to ???Off??? to use the VIDEO OUT terminal. ( 36)
Video is not output in
???Confirm that ???HDMI Resolution??? in the Setup menu is set properly. ( 39)
3D video is not output.
??? Are the settings on this unit and the TV correct? ( 27)
3D video is not output correctly as 2D.
???Select ???Set before play??? in the Setup menu, and select ???2D Playback??? in the setup screen displayed when playing 3D
discs. ( 37)
???Discs that have recorded titles with Side by side (2 screen structure) and that can be enjoyed in 3D are played back in accordance with the settings of the TV.
No subtitles.
???When progressive output is on, closed captions/subtitles cannot be displayed.
The subtitles overlap closed captions recorded on discs.
??? Turn off the subtitles or turn off the closed caption setting on the TV. ( 35)
A black band is displayed around the edge of the screen. The aspect ratio of the screen is abnormal.
??? Confirm the ???TV Aspect??? is set properly. ( 39) ??? Adjust the aspect setting on the television.
VQT3D27
44
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
??? Check connections to speakers and other equipment. ( 10, 11, 13s18)
??? Ensure the speaker settings for your speakers are correct. ( 41) ??? To output audio from a device connected with an HDMI cable, set ???HDMI Audio Output??? to ???On??? in the Setup menu. ( 39)
???When
???
from the HDMI AV OUT terminal. ( 36)
???Depending on the connected equipment, the sound may be distorted if this unit is connected with an HDMI cable.
???The
jIf the device has an optical audio output terminal, connect
???[BTT770] [BTT370]
(When using the 7.1ch speaker system)
Audio is not available from the surround back speakers even though Dolby Pro Logic II turns on.
Cannot switch audio.
???When audio is output from the HDMI AV OUT terminal, set ???Dolby D/Dolby D +/Dolby TrueHD??? or
No sound from the TV.
??? Press
If not labeled in this way, connect using the HDMI cable in combination with an optical digital audio cable.( 14, 15)
???If there is no sound from the equipment connected to this unit???s DIGITAL AUDIO IN terminal, please make sure that the optical audio output of the equipment is set to PCM.
iPod/iPhone operation
Cannot charge or operate.
??? Check that the iPod/iPhone is connected firmly. ( 32)
???The battery of the iPod/iPhone is depleted. Charge the iPod/ iPhone, and then operate again.
???When unexpected operation occurs while using the iPod/iPhone, connect the iPod/iPhone again or try to restart the iPod/iPhone.
Cannot display iPod/iPhone videos/photos on the TV.
??? Make sure that TV is connected to the VIDEO OUT terminal on this unit. ( 14)
???Operate the iPod/iPhone menu to make the appropriate video/photo output settings for your TV. (Refer to operating instructions for your iPod/iPhone.)
The TV input channel unintentionally changes to HDMI input.
???When the main unit is connected with an ???HDAVI Control??? compatible TV and VIDEO IN is selected for iPod/iPhone video or photo playback, the TV input channel will automatically change to the HDMI input channel when [HOME] is pressed.
Radio
Distorted sound or noise is heard.
??? Adjust the position of the antenna. ??? Use an outdoor antenna. ( 16)
A beat sound is heard.
???Try to keep a certain amount of distance between the antenna and the TV.
[BTT770]
Wireless system
No power.
???Ensure the AC power supply cord of the wireless system is connected properly.
The wireless link indicator is flashing.
???There is no link between the main unit and the wireless system. Turn the wireless system off and then back on. Alternatively, turn the wireless system off, disconnect the AC power supply cord and then reconnect it.
The wireless link indicator does not light.
???Check that the main unit is turned on, and the wireless system is turned on.
???Ensure that the digital transmitter is fully inserted into the slot
of the main unit. ( 17)
The wireless link indicator keeps flashing between red and green.
??? There is a power supply problem. Consult the dealer.
Messages
The following messages or service numbers appear on the television or unit???s display when something unusual is detected during startup and use.
On the television
Cannot play.
???You inserted an incompatible disc. (Discs recorded in PAL video, etc.)
Cannot display on this unit.
??? You tried to play a
No disc is inserted.
??? The disc may be upside down.
$ This operation is not available.
???Some operations are unsupported by the unit. For example;
reverse
IP address is not set.
???The ???IP Address??? in ???IP Address / DNS Settings??? is
No Video
???Depending on the connected iPod/iPhone, video menu may not be available on the TV. Select ???ALL??? on the unit???s display and operate video playback from your iPod/iPhone menu.
( 34)
I can???t connect to the network.
??? Confirm the network connection and settings. ( 17, 20, 40)
???Check the operating instructions for each device and connect accordingly.
Other difficulties with playback
??? Ensure the disc is for the correct
??? You have set a ratings level to limit
??? Some
I cannot play back
??? The SD card is
??? Confirm that this unit is connected to the broadband Internet. ( 17)
??? Confirm the
??? Confirm an SD Card is inserted into the SD Card slot. ( 22)
Alternative soundtrack and subtitles cannot be selected.
???The languages are not recorded on the disc.
???You may not be able to use the playback menu to change the soundtrack and subtitles on some discs. Use the disc???s
menus to make changes. ( 25)
F99
???The unit fails to operate properly. Press [POWER ??/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER ??/I] on the main unit again to turn the unit on.
U59
???The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.
Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the rear and side of the unit.
HDMI ONLY
??? Some
NET
??? While connecting to a network.
Reference
No PLAY
???There is a viewing restriction on a
Supplemental information
VQT3D27
46
???Made for iPod??? and ???Made for iPhone??? mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
For the software categorized as (5) includes as follows.
1.This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)
2.This product includes software developed by the University of California, Berkeley and its contributors.
3.FreeType code.
4.The Independent JPEG Group's JPEG software.
gSOAP Public License 1.3
Part of the software embedded in this product is gSOAP software. Portions created by gSOAP are Copyright (C)
THE SOFTWARE IN THIS PRODUCT WAS IN PART PROVIDED BY
GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Reference
VQT3D27
47
Specifications
GENERAL
1 kHz, 10 % total harmonic distortion
FRONT:
[BTT770] 185 W per ch (3 ???)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ???)
CENTER:
[BTT770] 180 W per ch (3 ???)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ???)
SURROUND:
[BTT770] 125 W per ch (3 ???)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ???)
100 Hz, 10 % total harmonic distortion
*[BTT370] When using
FM TUNER SECTION
SPEAKER SECTION
FRONT SPEAKERS
[BTT770]
[BTT370] [BTT273]
[BTT270]
TERMINAL SECTION
*Transfer rates are theoretical values; however, actual communication rate will vary according to communication environment or connected equipment.
VIDEO SECTION
[BTT770] WIRELESS SYSTEM
AND DIGITAL TRANSMITTER
Specifications are subject to change without notice.
File format
???With certain recording states and folder structures, the play order may differ or playback may not be possible.
Reference
VQT3D27
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company (referred to as ???the warrantor???) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (???warranty period???), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor.
During the ???Labor??? warranty period there will be no charge for labor. During the ???Parts??? warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for
For assistance in the U.S.A. and Puerto Rico in obtaining repairs, please ship the product prepaid to:
Panasonic Exchange Center
4900 George McVay Drive
Suite B
McAllen, TX 78503 panacare@us.panasonic.com
When shipping the unit, carefully pack, include all accessories, and send it prepaid, adequately insured and preferably in the original carton. When shipping Lithium Ion batteries please visit our Web Site at www.panasonic.com/BatteryHandling as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES
RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT
RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation,
improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER ???LIMITED WARRANTY COVERAGE???.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to the warrantor???s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
Customer Services Directory (United States and Puerto
Rico)
Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase
Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
For hearing or speech impaired TTY users, TTY:
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com Or, send your request by
npcparts@us.panasonic.com
You may also contact us directly at:
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY:
User memo:
DATE OF PURCHASE ________________________
DEALER NAME ______________________________
DEALER ADDRESS __________________________
___________________________________________
TELEPHONE NUMBER _______________________
VQT3D27
50
As of December 2010
The model number and serial number of this product can be found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for future reference.
MODEL NUMBER _____________________________
SERIAL NUMBER _____________________________
Limited Warranty (Only for CANADA)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT - LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc.
Technics Audio Product - One (1) year, parts and labour
Panasonic BD/DVD Product - One (1) year, parts and labour
Panasonic Audio Receivers - One (1) year, parts and labour
Home Theater Systems Product - One (1) year, parts and labour
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product was not sold "as is", and which product was delivered to you in new condition in the original packaging.
IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER
PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation,
Dry cell batteries are also excluded from coverage under this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL
PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded content. This list of items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory.
WARRANTY SERVICE
For product operation and information assistance, please contact:
PRODUCT OPERATION ASSISTANCE
PRODUCT REPAIRS
Please locate your nearest Authorized Servicentre.
Link: ???Support # Panasonic Servicentre?? locator??? on www.panasonic.ca
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton. Include details of the defect claimed, and proof of date of original purchase.
Reference
VQT3D27
51
Index
R
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 29
S
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . 35
V
VIERA CASTTM . . . . . . . . . . . . . . . . . . . 34
VIERA LinkTM ???HDAVI ControlTM??? . . . . 31
W
Wireless LAN . . . . . . . . . . . . . . . . . . . . 17
24p . . . . . . . . . . . . . . . . . . . . . . . . . 36, 39 3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
As an ENERGY STAR?? Partner, Panasonic has determined that
this product meets the ENERGY STAR?? guidelines for energy efficiency.
For Canada only: The word ???Participant??? is used in place of the word ???Partner???.
[BTT770] : Main unit only
F1210MH3011