4. SELF-DIAGNOSTICS

4-1. Self-Diagnostics Procedure

PROCEDURE

After turning on power to the air conditioner, use the remote controller and follow the steps below to execute self-diagnostics.

Step 1: Press and hold the remote controller NIGHT SET BACK (NSB) button and 1 HR TIMER button. Then, press and hold the ACL (reset) button with a pointed object such as the tip of a pen. After 5 seconds, release ACL button first, then release NIGHT SET BACK (NSB) and 1 HR TIMER buttons, "oP-1" (test run) appears, blinking in the remote controller clock display area.

Step 2: Next, press the 1 HR TIMER button once to change the display from "oP-1" to "oP-3" (self-diagnostics). (The display continues to blink.)

Step 3: Finally press the ON/OFF button to engage self-diagnostics mode.

???The self-diagnostics function utilizes the 3 indicator lamps on the main unit, in combinations of ON lamps, blinking lamps, and OFF lamps, to report the existence of sensor trouble or a protective operation. (The lamps blink or remain ON for 5 seconds, then turn OFF for 2 seconds.) Self-diagnostics is completed when the buzzer sounds 3 short beeps.

???A maximum of 3 self-diagnostics reports are displayed, for 5 seconds each, beginning with the most recent report. Following this display the lamps turn OFF. In order to view the self-diagnostics results again, press the ON/OFF button again.

???The 3 lamps remain OFF if no trouble has occurred.

<IMPORTANT> After self-diagnostics is completed, be sure to press the ACL (reset) button to return to normal mode. The air conditioner will not operate if this is not done.

< Clock display >

Test run mode

Self-diagnostics mode

ON/OFF operation button

NIGHT SETBACK button

1 HR.TIMER button

ACL (Reset) button

FEATURES

???Microprocessor Controlled Operation

The interior compartment of the remote controller contains several features to facilitate automatic operation, easy logically displayed for easy use.

???24-Hour ON or OFF Timer

This timer can be set to automatically turn the unit on or off at any time within a 24 hour period.

???1-Hour OFF Timer

This timer can be set to automatically turn off the unit at any time after one hour.

???Night Setback

This function saves energy by controlling operation to provide a quieter operating sound than normal.

???Automatic and 3-step Fan Speed

Auto/High/Medium/Low

???Air Sweep Control

This function moves a flap up and down in the air outlet, directing air in a sweeping motion around the room and providing comfort in every corner.

???Automatic Restart Function for Power Failure

Even when power failure occurs, preset programmed operation can be reactivated once power resumes.

???Automatic Switching between Cooling and Heating

This unit automatically switches between cooling operation and heating operation according to the difference between the room temperature and the temperature setting.

(This function is available only for ???Single use??? of COOL/DRY/ HEAT Model.)

???Hot Start Heating System

Right from the start, the air is warm and comfortable. This system prevents any cold blasts at the beginning while the heat pump is warming up, or even defrosting.

(This function is available only for COOL/DRY/HEAT Model.)

PRODUCT INFORMATION

If you have problems or questions concerning your wired remote controller, you will need the following information.

Model No. __________________________________

Date of purchase _____________________________

Dealer???s address _____________________________

Phone number _______________________________

SAFETY PRECAUTIONS

The following symbols used in this manual, alert you to potentially dangerous conditions to users, service personnel or the appliance:

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

This symbol refers to a hazard or unsafe CAUTION practice which can result in personal

injury or product or property damage.

INSTALLATION LOCATION

We recommend that this wired remote controller be installed properly by qualified installation technicians in accordance with the Installation Instructions provided with the unit.

???Do not install this wired remote controller where there are fumes or

flammable gases, or in an extremely humid space such as a greenhouse.

???Do not install the wired remote controller where excessively high heat-generating objects are placed.

Avoid:

To protect the air conditioner from heavy corrosion, avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa.

ELECTRICAL REQUIREMENTS

1.All wiring must conform to the local electrical codes. Consult your dealer or a qualified electrician for details.

2.Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring.

3.Wiring must be done by a qualified electrician.

NOTE

Pull off the power plug from a receptacle, or switch off the breaker, or switch off the power disconnecting mean to isolate the air conditioner from the main power supply when not in use for a long time.

SAFETY INSTRUCTIONS

???Read this Instruction Manual carefully before using this air conditioner. If you still have any difficulties or problems, consult your dealer for help.

???This air conditioner is designed to give you comfortable room conditions. Use this only for its intended purpose as described in this Instruction Manual.

???Confirm to authorized dealer or specialist on usage of specified refrigerant type.

Using of refrigerant other than the specified type may cause product damage, burst and injury etc.

???Never touch the unit with wet hands.

???Never use or store gasoline or other flammable vapor or liquid near the air conditioner ??? it is very dangerous.

???Do not use this appliance in a potentially explosive atmosphere.

???This air conditioner has no ventilator for intaking fresh air from outdoors. You must open doors or windows frequently when you use gas or oil heating appliances in the same room, which consume a lot of oxygen from the air. Otherwise there is a risk of suffocation in an extreme case.

???Do not swallow the battery.

???After removing the battery from remote controller, keep it away from the reach of children. The battery can cause death by suffocation if swallowed.

???To prevent possible hazards from insulation failure, the unit must be grounded.

???Do not clean inside the indoor and outdoor units by users. Engage authorized dealer or specialist for cleaning.

???In case of malfunction of this appliance, do not repair by yourself. Contact to the sales dealer or service dealer for a repair.

???Refrigerant gas leakage may cause fire.

???For safety, be sure to turn the air conditioner off and

also to disconnect the power before cleaning.

???Pull off the power plug from a receptacle, or switch off the breaker, or switch off the power disconnecting mean to isolate the air conditioner from the main power supply in case of emergency.

CAUTION

???Do not turn the air conditioner on and off from the power mains switch. Use the ON/OFF operation button.

???Do not stick anything into the air outlet of the outdoor unit. This is dangerous because the fan is rotating at high

speed.

??? Do not touch the air inlet or the sharp aluminum fins of the outdoor unit. You may get injured.

???Keep the fire alarm and the air outlet at least 1.5m away from the unit.

???Do not let children play with the air conditioner.

???Do not cool or heat the room too much if babies or invalids are present.

??? Do not sit or step on the unit. You may fall down accidentally.

??? Do not stick any object into the FAN CASE.

You may be injured and the unit may be damaged.

NOTICE

???This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

???This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

??? Reorient or relocate the receiving antenna.

??? Increase the separation between the equipment and receiver.

??? Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

??? Consult the dealer or an experienced radio/TV technician for help.

???FCC Caution: To assure continued compliance, follow the attached installation instructions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Press this button either to select the setting of the airflow direction to one of the six possible positions manually or to select the sweep function which moves the flap up and down automatically.

: The airflow direction can be set manually. (six positions)

: The flap moves up and down automatically.

NOTE

When you press the FLAP button, the air flow direction will be changed one by one as follows.

SWEEP

Timer and Present Time setting buttons

First, press the SET button to select the mode (ON, OFF and Present Time settings) you want.

Each time you press the ??????HH?????? button, the hours advance by one. (PM0, PM1.....PM11, AM0, AM1.....AM11)

Each time you press the ??????MM?????? button, the minutes advance by one when setting Present Time and by ten when setting ON and OFF Time.

ACL button (ALL CLEAR)

When you press the ACL button while the operation button is ON, all settings are cleared. Press the ACL button if the air conditioner is not operating correctly.

(1)Operation mode

AUTO .....................................

(only for COOL/DRY/HEAT Model)

HEAT ......................................

(only for COOL/DRY/HEAT Model)

MILD DRY ..............................

COOL .....................................

FAN ........................................

(2)Fan speed

Automatic operation ...............

HIGH .....................................

MEDIUM.................................

LOW .......................................

(3)Temperature setting

60 ??? 86 ??F ..............................

When set to 80 ??F temperature indication ...........

(4)Timer

24-hour clock with ON/OFF program Timer .......................

ON Timer. ..............................

OFF Timer. ............................

1-hour OFF Timer. .................

(5)NIGHT SETBACK..................

(6)Flap angle indication..............

Sweep indication....................

1.Automatic Operation

(only for COOL/DRY/HEAT Model)

???Single use

This unit automatically switches between cooling operation and heating operation according to the difference between the room temperature and the temperature setting.

???Multiple use

The air conditioner calculates the difference between the thermostat setting and room temperature, and automatically determines the mode to operate under cooling or heating. Then, the air conditioner continuously operates under the mode selected at initial operation.

STEP 2

STEP 1

NOTE Check that the circuit breaker on the power panel is turned on.

Once mode is selected and the unit is preset by following the steps below, you can have the air conditioner automatically bring the room to the desired temperature simply by pressing the ON/OFF operation button.

STEP 1 Press the MODE selector button to .

STEP 2 Press the ON/OFF operation button.

To stop the air conditioner, press the ON/OFF operation button again.

NOTE To change the temperature setting; press the temperature setting buttons and change the setting to the desired temperature.

2. Manual Operation

NOTE Check that the circuit breaker on the power panel is turned on.

If the automatic operation settings of the unit do not meet your needs, press the setting buttons as described below and change the settings as desired.

STEP 2 To start the air conditioner, press the ON/ OFF operation button.

STEP 3 Press the TEMP. setting buttons to change the temperature setting to the desired temperature.

Adjustable temperature range: 86 ??F max.

60 ??F min.

STEP 4 Set the FAN SPEED selector button to the setting you want.

STEP 5 Press the FLAP button and set the airflow direction as desired.

(Refer to ???ADJUSTING THE AIRFLOW DIRECTION??? on page 10.)

To stop the air conditioner, press the ON/OFF operation button again.

NOTE ??? Choose the best position in the room for the remote controller, which also acts as the sensor for room comfort and transmits the operating instructions. Once you???ve found this best position, always keep the remote controller there.

???This appliance has a built-in 5-minute time delay circuit to ensure reliable operation. When the operation button is pressed, the compressor will start running within three minutes. In the event of power failure, the unit will stop.

???The display on the remote controller shows the setting temperature and not the room temperature.

???When multiple indoor units are used and units in other rooms are already operating, they will be operating with the same mode as the operating indoor units. (only for ???Multiple use??? of COOL/DRY/HEAT Model)

3. Adjusting the Fan Speed

A. Automatic fan speed

Simply set the FAN SPEED selector button to the position.

This automatically sets the best fan speed for the room temperature.

B. Manual fan speed

If you want to adjust fan speed manually during operation, just set the FAN SPEED selector button as desired. [ , , or ]

4. Fan Only

STEP 2

If you want to circulate air without any temperature control, follow these steps:

STEP 1 Press the MODE selector button to switch to the fan mode .

STEP 2 Press the ON/OFF operation button.

STEP 3 Press the FAN SPEED selector button to select the fan speed of your choice ( , or ).

NOTE There is no FAN only function in ???Multiple use??? of COOL/DRY/HEAT Model.

5. Night Setback Mode

Night Setback Mode is used for saving energy.

Press the NIGHT SETBACK button while unit is operating. The mark appears in the display.

To release the night setback function, press the NIGHT SETBACK button again.

A. In Cooling and DRY Mode: ( and )

When the night setback mode is selected, the air conditioner automatically raises the temperature setting 2 ??F when 30 minutes have passed after the selection was made, and then another 2 ??F after another 30 minutes have passed, regardless of the indoor temperature when night setback was selected. This enables you to save energy without sacrificing comfort. This function is convenient when gentle cooling is needed.

SETBACK button

B.In Heating Mode: ( )

(only for COOL/DRY/HEAT Model)

When the night setback mode is selected, the air conditioner automatically lowers the temperature setting 4 ??F when 30 minutes have passed after the selection was made, and then another 4 ??F after another 30 minutes have passed, regardless of the indoor temperature when night setback was selected. This enables you to save energy without sacrificing comfort. This function is convenient when gentle heating is needed.

SETBACK button

SPECIAL REMARKS

Power failure during operation

In the event of power failure, the unit will stop. When the power is resumed within 8 hours, the unit will restart automatically in approximately five minutes, or 15 minutes in ???Multiple use??? of COOL/ DRY/HEAT Model on AUTO mode by the remote controller.

Remote Controller

The remote controller sends the setting condition to the air conditioner regularly at five minute intervals.

Remote Controller Display

If the display malfunctions, press the ACL button.

This resets the remote controller back to the initial settings. Make the settings again.

SETTING THE TIMER

1. How to set the present time

(Example) To set to 9:10 pm.

2. How to set the OFF time

(Example) To stop the air conditioner at 11:30 pm.

To cancel the setting, press the TIMER SELECT button twice.

3. How to set the ON time

(Example) To start operation at 7:10 am.

To cancel the setting, press the TIMER SELECT button three times.

4. How to set daily ON/OFF repeat timer

(Example) To start operation at 7:10 am. and stop the air conditioner at 11:30 pm.

To cancel the setting, press the TIMER SELECT button once.

NOTE

You can check the timer ON/OFF times after you have set them by pressing the SET button.

5. Backup function

Even if the main power supply to the unit is turned off, the remote controller will store the previous settings in its internal memory for up to 8 hours. If the power is not turned back on within 8 hours, the previous settings will be lost. In this case, the mode settings must be reset by the user.

USING THE 1-HOUR OFF

TIMER

1. 1-Hour OFF Timer

This function causes the unit to operate for one hour and then stop, regardless of whether the unit is on or off when this button is pressed.

The indicator in the display indicates that this function is operating.

Setting procedure:

ADJUSTING THE AIRFLOW

DIRECTION

The vertical airflow can be adjusted by moving the flap with the remote controller. Do not move the flap with your hands. Confirm that the remote controller has been turned on. Use the FLAP button to set either the sweep function or one of the six airflow direction settings.

A. Sweep function

The flap starts moving up and down to deliver air over the sweep range.

Regardless of whether the unit is operating or stopped, press the 1 HR. TIMER button.

appears in the display.

Cancellation procedure:

Press the ON/OFF operation button to turn the unit off, wait for the unit to stop operating, and then press the ON/OFF operation button again.

The 1-Hour Timer function is now cancelled and the unit operates normally.

NOTE

B. Setting the airflow manually

Referring to the above illustration, use the FLAP button to set the airflow direction within the range used during the heating, cooling, or dehumidifying operation.

???If, while the 1-Hour Timer function is operating, the 1HR. TIMER button is pressed once to cancel the function and then again, the unit continues to operate for one hour from that point in time and then stops.

???It is not possible to use the OFF Timer and 1-Hour OFF Timer together. Whichever function is set last takes precedence. If the 1 HR. TIMER button is pressed while the TIMER OFF function operates, the OFF Timer is cancelled and the unit will stop operating one hour later.

2.Operation together with the daily ON/OFF repeat timer

The 1-Hour OFF Timer setting is given priority over the DAILY ON/ OFF REPEAT setting.

NOTE

???The flap automatically closes when the unit is off.

???During the heating operation, the fan speed will be very low and the flap will be in the horizontal position (position ) until the air being blown out of the unit begins to warm. Once the air warms up, the flap position and fan speed change to the settings specified with the remote controller.

CAUTION

???Use the FLAP button on the remote controller to adjust the position of the flap. If you move the flap by hand, the flap position according to the remote controller and the actual flap position may no longer match. If this should happen, shut off the unit, wait for the flap to close, and then turn on the unit again; the flap position will now be normal again.

???Do not have the flap pointed down during cooling operation. Condensation may begin to form around the air vent and drip down.

Parts supplied with the remote controller

See Table 1.

Remote controller installation guidelines

Installation location

??Mount the remote controller 3.3 to 4.9 ft. (1 to 1.5 meters) off the floor where it can sense the average temperature of the room.

??Do not mount the remote controller in a place exposed to direct sunlight or where it is exposed to outside air such as near a window.

??Do not mount the remote controller behind a curtain or other object so that it is separated from the air circula- tion of the room.

??Mount the remote controller inside the room being air conditioned.

Switching the room temperature sensor

Table 1

In-wall junction box (locally purchased)

from the indoor unit

In-wall junction box

Opening

Wire harness

Back plate

Machine screws

Remote controller

Fig. 3

PCB

Wall

Spacers

NOTE

??When installing the remote controller back plate, be sure that it is flat and straight. Do not over-tighten the installa- tion screws.

??Install the remote controller away from all sources of elec- trical noise.

??Install a noise filter or take other appropriate action if elec- trical noise affects the power supply circuit of the unit.

Wire harness

Cut out

Wall

Back plate

Tapping screws

Remote controller

Fig. 6

How to wire the remote controller

(1)Turn OFF the power and remove the ceiling panel air-intake grille. (Refer to 3-6-1 Before Installing the Ceiling Panel in the Installation Instructions supplied with the indoor unit.)

(2)Remove the 3 power box cover screws and 2 control box cover screws, then remove both covers. At this time, take care not to drop the covers. (Fig. 7)

(3)Disconnect the 7P (IND) terminal and 4P (RC) termi- nal of the 7P IND and 4P RC wiring connectors and the 5P terminal of the 5P FLAP wiring connector from the control box PCB connectors (IND, RC, FLAP). Disconnect each wiring connector from the clamp that fastens it. (Fig. 7)

(4)Remove the ceiling panel. (To remove the ceiling panel, follow the steps for 3-6 How to Install the Ceiling Panel in the reverse order. Refer to the Installation Instructions supplied with the indoor unit.)

Control box cover

Power box cover

Indicator

How to Test Run the Air Conditioner

After turning on the power of the air conditioner, use the remote controller and follow the steps below to conduct the test run.

(1) Set the remote controller in Test Run mode. (Fig. 9)

a)Press and hold the NIGHT SETBACK button and the 1HR. TIMER button.

b)Then press and hold the ACL (Reset) button with a pointed object such as the tip of a pen. After 5 seconds, release the ACL button first.

c)Then release the NIGHT SETBACK and 1HR. TIMER buttons.

d) appears and ???oP-1??? blinking in the remote controller clock display area. (Fig. 10)

(2)Start Cooling mode test run by pressing the ON/OFF operation button of the remote controller. (Fig. 9)

??This starts the fan producing uncooled forced air with the 3 indicator lamps (OPERATION lamp, TIMER lamp, and HIGH POWER lamp) on the main unit blinking. (Fig. 11)

??After 3 minutes, the system shifts into cooling operation, and cool air will start to be felt. Cooling mode test run is unaffected by the room tempera- ture.

(3)Press the ON/OFF operation button of the remote controller again to stop the test run. (Fig. 9)

(4)Finally press the ACL (Reset) button of the remote controller to release it from Test Run mode to return to normal mode. (Fig. 9)

????? ??? and ???oP-1??? will disappear from the remote controller clock display area.

NOTE

Troubleshooting:

In the event that the green OPERATION lamp is blink- ing upon powering up the system, an error condition exists. In this case, refer to the self-diagnostics proce- dure which can be seen by opening the air-intake grille.

IMPORTANT

After the test run is completed, be sure to press the ACL (Reset) button to return to normal mode. The air conditioner will not operate correctly if this is not done.

ON/OFF

operation button

NIGHT SETBACK button

1 HR.TIMER button

Fig. 10

OPERATION button

OPERATION lamp

TIMER lamp

HIGH POWER lamp

REMOTE CONTROL receiver

Fig. 11

WI1011-0

Printed in China

Installing the connection kit

A.7000 BTU, 9000 BTU, and 12000 BTU inverter models

(1)Remove the air intake grille.

(2)Remove the terminal cover. Pull out the thermistor, then remove the grille.

??For details on steps (1) and (2), refer to the Installation Instructions included in the outdoor unit package.

(3)Disengage the top cover from the tabs on the sides of the component box, then pull the cover toward you to remove it. (Fig. 1)

(To disengage the tabs, pull the sides of the top cover sideways and out- ward from the component box.)

Component box

(4)Remove the 4 component box installation screws. (Fig. 1)

(5)Disconnect the indicator-side connec- tor (10P) of the wires that connect the indicator and component box (Fig. 2a). Then disconnect the connector on the component box side (10P) and remove the wires. (Lifting the P.C. board up slightly will make this work easier.) (Fig. 2b)

(6)After removing the wires, insert Connector 1 of the wires (Fig. 3a) that were included in the kit package into the indicator (Fig. 2a), then insert Connector 2 into the component box. (Fig. 2b)

At this time, pass the wires through so that they are held inside the 2 holders on the sides of the component box.

(Fig. 3b)

Connector (10P)

Indicator

Fig. 2a

Connector 1

(10P)

Fig. 3a

Fig. 1

P.C. board

Connector (10P)

Fig. 2b

Holder

Fig. 3b

(7)Feed the wire harness that was included in the wired remote controller package into the right lower rear of the unit and route it to the component box. (Fig. 4a)

??When feeding the wire harness through the opening, be careful of the motor cable and be sure to feed the wire harness and motor cable together through the opening. (Fig. 4b)

??Be careful not to damage the wire harness when installing the conduit during unit installation work.

Motor cable

Component box

Wire harness

Opening

Wire harness

Fig. 4b

(8)Cut the wire tube that was included in the kit package to a length of approximately 4 inches (100 mm), then feed the wire harness through it. Then connect Connector 3 (Fig. 3a) to the wire harness connector (4P). (Fig. 4c)

(9)Take the wires (Fig. 3a) and use a wire clamp to bind together the wire for the noise filter and the wire for the thermistor (Fig. 5a). Then position them so that the noise filter is contained within the space of the component box. (Fig. 5b)

Fig. 4a

Connector 3

(4P) Connector 3

(4P)

Connector (4P)

Wire harness

Wire tube Connector (4P)

Fig. 4c

(12) Route the wire harness

Wire harness

Air intake grille

out through the small cut-out located at the bottom right side of the indoor unit frame. (Fig. 7a)

Self-diagnostic label

(13) Apply the label that was included in the package at a location close to the self-diagnostic label applied to the air intake grille. (Fig. 7b)

< Completion drawing >

Fig. 6b

B. 18000 BTU and 24000 BTU inverter models

(1)Remove the air intake grille.

(2)Remove the terminal cover. Pull out the thermistor, then remove the grille.

??For details on steps (1) and (2), refer to the Installation Instructions included in the outdoor unit package.

(3)Disengage the top cover from the tabs on the sides of the component box, then pull the cover toward you to remove it. (Fig. 1)

(To disengage the tabs, pull the sides of the top cover sideways and outward from the component box.)

(4)Disconnect the indicator-side connector (10P) of the wires that connect the indi- cator and component box (Fig. 2a). Then disconnect the connector on the com- ponent box side (10P) and remove the wires. (Lifting the P.C. board up slightly will make this work easier.) (Fig. 2b)

(5)After removing the wires, insert Connector 1 of the wires (Fig. 3a) that were included in the kit package into the indicator (Fig. 2a), then insert Connector 2 into the component box. (Fig. 2b)

At this time, pass the wires through so that they are held inside the 2 holders on the sides of the component box. (Fig. 3b)

(6)Feed the wire harness that was included in the wired remote controller package into the right lower rear of the unit. (Fig. 4a)

??Be careful not to damage the wire harness when installing the conduit during unit installation work.

(7)Pass the wire harness through the wire tube that was included in the kit package. Then connect Connector 3 (Fig. 3a) to the wire harness connector (4P). (Fig. 4c)

(8)Take the wires (Fig. 3a) and use a wire clamp to bind together the wire for the noise filter and the wire for the thermistor (Fig. 5a). Then position them so that the noise filter is contained within the space of the component box. (Fig. 5b)

(9)Pass the wire tube through the clamping strap, and temporarily fasten in place with the screw. Next, use a clamp and bind the wires together immediately above the clamping strap, and fasten in place with the screw in order to prevent pulling on the wire harness. (Fig. 6a)

??Install the wire tube so that the wires cannot be damaged by the edge of the metal plate. (Fig. 6a)

??When re-installing the grille, confirm that there is no slack in the wire harness wires.

(10)Install the top cover on the component box. (Fig. 8)

(11)Route the wire harness out through the small cut-out located at the bottom right side of the indoor unit frame. (Fig. 7a)

(12)Apply the label that was included in the package at a location close to the self- diagnostic label applied to the air intake grille. (Fig. 7b)

(13)Refer to the Installation Instructions that were included in the outdoor unit pack- age and re-install the grille, thermistor, terminal cover, and air intake grille.

< Completion drawing >

Fig. 8

How to Test Run the Air Conditioner

After turning on the power of the air conditioner, use the remote controller and follow the steps below to conduct the test run.

(1)Set the remote controller in Test Run mode. (Fig. 9)

a)Press and hold the NIGHT SETBACK button and the 1HR. TIMER button.

b)Then press and hold the ACL (Reset) button with a pointed object such as the tip of a pen. After 5 seconds, release the ACL button first.

c)Then release the NIGHT SETBACK and 1HR. TIMER buttons.

d) appears with ???oP-1??? blinking in the remote controller clock display area. (Fig. 10)

(2)Start Cooling mode test run by pressing the ON/OFF operation button of the remote controller. (Fig. 9)

??This starts the fan producing uncooled forced air with the 3 indicator lamps (OPERATION lamp, TIMER lamp, and QUIET lamp) on the main unit blinking. (Fig. 11)

??After 3 minutes, the system shifts into cooling operation, and cool air will start to be felt. Cooling mode test run is unaffected by the room tempera- ture.

(3)Press the ON/OFF operation button of the remote controller again to stop the test run. (Fig. 9)

(4)Finally press the ACL (Reset) button of the remote controller to release it from Test Run mode to return to normal mode. (Fig. 9)

????? ??? and ???oP-1??? will disappear from the remote controller clock display area.

NOTE

Troubleshooting:

In the event that the green OPERATION lamp is blink- ing upon powering up the system, an error condition exists. In this case, refer to the self-diagnostics proce- dure on the inside of the air-intake grille.

IMPORTANT

After the test run is completed, be sure to press the ACL (Reset) button to return to normal mode. The air conditioner will not operate correctly if this is not done.

ON/OFF

operation button

NIGHT SETBACK button

1 HR.TIMER button

Fig. 10

OPERATION lamp

TIMER lamp

QUIET lamp

Fig. 11

WI1011-0

Printed in Japan

Installing the connection kit

(1)Remove the air intake grille.

??)RUWKHGHWDLOVRIVWHSUHIHUWRWKH,QVWDOODWLRQ

,QVWUXFWLRQVWKDWZHUHSURYLGHGZLWKWKHRXWGRRUXQLW

 'LVHQJDJHWKHWDERQWKHERWWRPRIWKHHOHFWULFDOER[ FRYHUWKHQOLIWXSWKHFRYHUDQGGLVHQJDJHWKHWDERQWKH WRSRIWKHFRYHU7KHQUHPRYHWKHHOHFWULFDOER[FRYHU

)LJ

 'LVFRQQHFW&RQQHFWRU3&RQQHFWRU3DQG &RQQHFWRU3IURPWKH3&ERDUG3&%)LJ

 'UDZWKH3&%DSSUR[LPDWHO\KDOIZD\RXWRIWKHHOHFWULFDO ER[:KHQGUDZLQJLWRXWSXVKWKHUHWDLQHUWDEWKDWIDV WHQVWKH3&%LQSODFHVOLJKWO\WRZDUGWKHRXWVLGH)LJ

Tab

RQWRS

(OHFWULFDOER[FRYHU

Tab

(on bottom)

Draw the PCB out carefully so that CAUTION the wiring inside the electrical box does not damage the capacitor, IC,

or other components.

3&%

2. Draw out halfway

Retainer tab

1. Push to side slightly

(OHFWULFDOER[

Fig. 1

&RQQHFWRU

3&%

&RQQHFWRU

&RQQHFWRU

(OHFWULFDOER[

Fig. 2

:'

:LUHKDUQHVV

1RLVHILOWHU

:LUH

KDUQHVV

&ODPS

1RLVHILOWHU

:LUHKDUQHVV

Fig. 7

 5HLQVWDOOWKHHOHFWULFDOER[FRYHU

 $SSO\WKHVXSSOLHGODEHOFORVHWRWKHVHOIGLDJQRV

WLFVODEHORQWKHLQVLGHRIWKHUHPRYHGDLULQWDNH JULOOH)LJ

 5HLQVWDOOWKHDLULQWDNHJULOOH ??)RUWKHGHWDLOVRIVWHSUHIHUWRWKH,QVWDOODWLRQ

,QVWUXFWLRQVWKDWZHUHSURYLGHGZLWKWKHRXWGRRU XQLW

:KHQLQVWDOOLQJWKHDLULQWDNHJULOOHLQVWDOOLWVRWKDW

WKHZLUHKDUQHVVIRUWKHZLUHGUHPRWHFRQWUROOHU

HPHUJHVIURPWKHVPDOORSHQKROHRQWKHULJKWVLGH RIWKHJULOOH)LJ

Wire harness

Clamp

Fig. 8

$LULQWDNHJULOOH

6HOIGLDJQRVWLFV label

/DEHO 6XSSOLHG

,QVLGHDLULQWDNHJULOOH

Fig. 9

Open hole

Wire harness

Fig. 10

How to Test Run the Air Conditioner

$IWHUWXUQLQJRQWKHSRZHURIWKHDLUFRQGLWLRQHUXVHWKH

UHPRWHFRQWUROOHUDQGIROORZWKHVWHSVEHORZWRFRQGXFW WKHWHVWUXQ

 6HWWKHUHPRWHFRQWUROOHULQ7HVW5XQPRGH)LJ D 3UHVVDQGKROGWKH1,*+7 6(7%$&.EXWWRQDQG

WKH+57,0(5EXWWRQ

E 7KHQSUHVVDQGKROGWKH$&/ 5HVHWEXWWRQZLWK DSRLQWHGREMHFWVXFKDVWKHWLSRIDSHQ$IWHU VHFRQGVUHOHDVHWKH$&/ EXWWRQILUVW

F 7KHQUHOHDVHWKH1,*+7 6(7%$&.DQG+5 7,0(5EXWWRQV

G DSSHDUVZLWK??R3??EOLQNLQJLQWKHUHPRWH FRQWUROOHUFORFNGLVSOD\DUHD)LJ

 6WDUW&RROLQJPRGHWHVWUXQE\SUHVVLQJWKH 212))RSHUDWLRQEXWWRQRIWKHUHPRWHFRQWUROOHU

)LJ

??7KLVVWDUWVWKHIDQSURGXFLQJXQFRROHGIRUFHGDLU ZLWKWKHLQGLFDWRUODPSV23(5$7,21ODPS 7,0(5ODPSDQGRQWKHPDLQXQLWEOLQNLQJ )LJ

??$IWHUPLQXWHVWKHV\VWHPVKLIWVLQWRFRROLQJ RSHUDWLRQDQGFRRODLUZLOOVWDUWWREHIHOW&RROLQJ PRGHWHVWUXQLVXQDIIHFWHGE\WKHURRPWHPSHUD WXUH

 3UHVVWKH212))RSHUDWLRQEXWWRQRIWKHUHPRWH FRQWUROOHUDJDLQWRVWRSWKHWHVWUXQ)LJ

 )LQDOO\SUHVVWKH$&/ 5HVHWEXWWRQRIWKHUHPRWH FRQWUROOHUWRUHOHDVHLWIURP7HVW5XQPRGHWRUHWXUQ WRQRUPDOPRGH)LJ

??????DQG??R3??ZLOOGLVDSSHDUIURPWKHUHPRWH

FRQWUROOHUFORFNGLVSOD\DUHD

NOTE

7URXEOHVKRRWLQJ

,QWKHHYHQWWKDWWKHJUHHQ23(5$7,21ODPSLVEOLQNLQJ XSRQSRZHULQJXSWKHV\VWHPDQHUURUFRQGLWLRQH[LVWV ,QWKLVFDVHUHIHUWRWKHVHOIGLDJQRVWLFVSURFHGXUHRQ WKHLQVLGHRIWKHDLULQWDNHJULOOH

IMPORTANT

$IWHUWKHWHVWUXQLVFRPSOHWHGEHVXUHWRSUHVVWKH$&/

5HVHWEXWWRQWRUHWXUQWRQRUPDOPRGH7KHDLUFRQGL WLRQHUZLOOQRWRSHUDWHFRUUHFWO\LIWKLVLVQRWGRQH

ON/OFF

operation button

NIGHT SETBACK button

1 HR.TIMER button

Fig. 12

OPERATION lamp

TIMER lamp

Fig. 13

WI1011-0

Printed in Japan