Panasonic_Camera_Accessories

Read this first !

)&&127,&(86$

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

CAUTION:

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

:DUQLQJ

To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also, any unauthorized changes or modifications to this equipment could void the user???s authority to operate it.

1RWLFH86$RQO\

Disposal may be regulated in your community due to Environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.

(((<|QHWPHOL??LQH8\JXQGXU

(((&RPSOLHVZLWK'LUHFWLYHRI7XUNH\

A rechargeable battery that is recyclable powers the product you have purchased.

Read this first !FRQWLQXHG

EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS

1.$SSOLFDEOHVWDQGDUGVDQGRSHUDWLQJHQYLURQPHQW

7KHDSSDUDWXVLVFRPSOLDQWZLWK

?? standards EN55103-1 and EN55103-2 2009, and ?? electromagnetic environments E1, E2, E3 and E4.

3UHUHTXLVLWHFRQGLWLRQVWRDFKLHYLQJFRPSOLDQFHZLWKWKHDERYHVWDQGDUGV

!3HULSKHUDOHTXLSPHQWWREHFRQQHFWHGWRWKHDSSDUDWXVDQGVSHFLDOFRQQHFWLQJFDEOHV

?? The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the apparatus.

?? The purchaser/user is urged to use only the connecting cables described below.

!)RUWKHFRQQHFWLQJFDEOHVXVHVKLHOGHGFDEOHVZKLFKVXLWWKHLQWHQGHGSXUSRVHRIWKHDSSDUDWXV

?? Video signal connecting cables

Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).

Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.

?? Audio signal connecting cables

If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU. Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.

?? Other connecting cables (IEEE1394, USB)

Use shielded cables, which provide quality performance for high-frequency applications, as connecting cables.

?? When connecting to the DVI signal terminal, use a cable with a ferrite core.

?? If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.

3.Performance level

The performance level of the apparatus is equivalent to or better than the performance level required by these standards.

However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse effects of the

interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being affected and with its operating environment:

1.Place the apparatus at a distance from the source of the interference.

2.Change the direction of the apparatus.

3.Change the connection method used for the apparatus.

4.Connect the apparatus to another power outlet where the power is not shared by any other appliances.

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

Read this first !FRQWLQXHG

IMPORTANT SAFETY INSTRUCTIONS

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings. Install in accordance with the manufacturer???s instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

7UDQVSRUWDWLRQSUHFDXWLRQV

Do not try to lift the monitor by grabbing the panel.

Do not place the monitor face down during transportation to prevent damaging it. Keep it upright.

Do not expose the LCD panel to strong pressure or pressure from pointed objects. Take care especially during transportation.

Exposing the LCD panel to strong pressure may result in blurring or other damage.

Contents

6WDQGDUGDFFHVVRULHV??2SWLRQDOXQLWV

?? Standard accessories

??7LOW6WDQG?? ??7LOW6WDQG0RXQWLQJ6FUHZ?? ??&'520??

(The unit is shipped with the tilt stand already attached with the four screws.)

??2SWLRQDOXQLWV

?? VF Cable BT-CS910G

$ERXWWKLVLQVWUXFWLRQPDQXDO

??This instruction manual refers to BT-LH910G as ???this unit.???

??The illustrations, explanatory drawings, and other figures included in this instruction manual are for illustrative purposes only and may differ from actual display.

??HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and/or other countries.

3UHFDXWLRQVIRU8VH

This product has been specially designed for commercial use. As such, it should be used and operated only by persons with related expertise.

??The LCD screen is manufactured to precise specifications. Although over 99.99 % of the pixels function normally, 0.01 % of the pixels are either missing or constantly lit (red, blue or green). This is normal and not a cause for concern.

??The protection panel and liquid crystal panel is a specially manufactured component. Wiping it with a hard cloth, or rubbing it vigorously will scratch the surface.

??If a still image is displayed for an extended period of time, it may generate a temporary afterimage (phosphor burn-in). (However, such images can be removed by displaying normal video for a while.)

??The response speed and brightness of liquid crystal vary with ambient temperatures.

??Do not install the unit in locations where enough space cannot be provided around it as heat may build up inside preventing normal operation. Be sure to provide enough space around the unit.

??Exposing the LCD screen to intense light sources will impair its characteristics and lower image quality.

??In an environment exposed to drastic temperature fluctuations, condensation may build up on

and inside the LCD screen. This may lower the quality of the screen and may damage it. If there are drops of water on the case, turn off the power and wait until the condensation has evaporated.

??Some video images may appear blurred on the screen.

??Leaving the unit in a location exposed to high temperature and humidity for an extended period of time may damage the LCD screen and cause blurring.

??Do not use the unit in excessively dusty environments. Doing so may damage the LCD screen.

??Using the unit in cases such as the following may result in image and audio distortion due to the influence of electromagnetic waves.

??When in the vicinity of a TV or computer

??When a mobile phone is on top of the unit

??When near equipment that generates a power magnetic field, such as a speaker or large motor

??If the unit becomes unable to operate properly due the influence of equipment that generates magnetism, turn off the unit (if using a battery, remove it) and then wait a while and then turn it back on.

??Using the unit near radio broadcast equipment or high-voltage equipment may result in image and audio degradation.

5HTXHVW

3OHDVHFRQILJXUHWKHIROORZLQJVHWWLQJEHIRUHXVLQJWKHXQLWIRUWKHILUVWWLPH

?? 7KHXQLWLVVKLSSHGZLWKWKHDUHDRIXVHVHWWRWKHLQLWLDOVWDWH%HIRUHXVLQJWKHXQLWVHW \RXUDUHDRIXVHDVGHVFULEHGLQ??6HOHFWLQJ$UHDRI8VH??RQSDJH

2XWOLQH

This unit is a liquid crystal display monitor for broadcasting and business use that is equipped with a 23 cm (9.0 inch) (effective display area) liquid crystal display.

It can be used as a VF (viewfinder) for broadcasting and business cameras made by Panasonic.

??+LJK3HUIRUPDQFH/LTXLG&U\VWDO3DQHO

This product incorporates a WXGA (1280 x 768) class high-resolution IPS liquid crystal panel. It offers excellent color reproduction, a wide viewing angle, and a fast response time.

??6XSHUE0RYLQJ,PDJH4XDOLW\$FKLHYHGE\1HZ,PDJH3URFHVVLQJ(QJLQH

??The 10-bit image processing engine facilitates accurate and smooth gradation results from low to high brightness levels.

??The incorporation of an I/P conversion circuit with a low delay of less than one field minimizes the delay time between signal input and monitor display.

??The incorporation of diagonal line compensation circuit reduces image degradation in the vertical direction and jagged noise on diagonal lines.

??The high-speed moving image response time provides vivid and clear image display.

??Gamma compensation is performed for each monitor.

??,QFOXGHV'$VVLVW)XQFWLRQV

Various assist functions are included to allow connecting the left and right connectors of a 3D camera to the two SDI inputs and capturing 3D images that are easier to view on a 2D monitor. These functions also make camera adjustments easier and reduce the preparation time required for 3D shooting.

??:LGH9DULHW\RI)XQFWLRQVDQG,QWHUIDFHV

??Equipped with 3G-SDI, SDI (HD/SD compatible), HDMI, VIDEO, and YPBPR inputs.

??FOCUS-IN-RED function (Displayed abbreviated to F-IN-R in the picture adjusting knob status display.) Making camera focus adjustments is extremely easy because the section of the image in focus is displayed in red to make it easy to understand what is in focus.

??WFM (Y/R/G/B) and vectorscope display functions

Capable of input signal Y/R/G/B waveform display (when 3G-SDI, SDI, HDMI, VIDEO, or YPBPR input) and vectorscope display.

??Audio level meter display function and headphones jack

The level of audio signals embedded in 3G-SDI, SDI, and HDMI signals can be displayed. Furthermore, support is also included for reference point setting, peak hold, and overrange display.

The incorporation of a headphones jack means you can check the audio. The channel can also be selected in a menu.

??Closed caption function

The captions added to video signals can be displayed during SDI and VIDEO input.

??2-screen display function

The screen can be split into two to allow you to make a screen comparison for the same input connectors and same format.

??PIXEL TO PIXEL function

This function makes camera focus adjustment extremely easy because the input signals are displayed without being resized.

When resizing is not performed, the 1080/60i signals can be expanded to the equivalent of an approximately 13.5-inch wide monitor, and then checked.

??Cross hatch display function

This function displays markers at regular vertical and horizontal intervals to facilitate easy composition.

6HOHFWLQJ$UHDRI8VH

The unit is shipped with the area of use set to the initial setting (NTSC) state. Before using the unit, select the area of use. When you set the area of use, the factory default setting of the menu item on the right is set to the value that matches the area of use. (For the procedure to restore the menu setting values to the factory defaults, refer to ???Loading user data??? on page 23.)

How to Select Area of Use

1.&RQQHFWWKHXQLWWRWKHSRZHUVXSSO\WXUQRQWKHSRZHUDQGSUHVVWKH>0(18@EXWWRQ

The MAIN MENU screen appears.

2.3UHVV> @> @WRVHOHFW??6<67(0&21),*??DQGSUHVV>(17(5@

The ???SYSTEM CONFIG??? submenu screen appears.

3.3UHVV> @> @WRVHOHFW??$5($6(77,1*??DQGSUHVV>(17(5@

The ???AREA SETTING??? value turns green.

4.3UHVV> @> @WRVHOHFWWKHDUHDRIXVHIURP??176&176&-3$/??DQGSUHVV>(17(5@

The ???YES/NO??? confirmation screen appears.

5.3UHVV> @> @WRVHOHFW??<(6??DQGSUHVV>(17(5@

The setting selected in step 4 is reflected in the factory defaults (FACTORY) or the current menu setting values and the ???SYSTEM CONFIG??? submenu screen appears.

6.3UHVV>0(18@WZLFHWRFORVHWKHPHQX

&RQWUROVDQG7KHLU)XQFWLRQV

Front panel

1 +($'3+21(6RXWSXWMDFN0VWHUHRPLQLMDFN

Allows you to connect headphones to check the audio when inputting an SDI signal or HDMI signal. * The volume and sound quality differ depending on the headphones.

?? In 3D assist mode, the audio of the SDI1 (L) side can be checked.

2POWER switch/lamp

Switches the power supply ON/OFF. When the power is ON, the LED (green) lights up.

3 ,13876(/(&7EXWWRQ

Selects the signal input line. Each time the button is pressed, the input changes in the following order:

9,'(2 6', 6', +'0, <3BPR 9) ,176*

INT SG: Internal chart for adjustment [Color Bar + Grayscale] (page 74)

??The input line when the power supply is switched ON is the one that was selected the last time the power was switched OFF. The INPUT SELECT menu settings can be used to skip input lines that are not used.

??In 3D assist mode, the input is fixed to SDI1/SDI2 and the input line cannot be selected.

??When the control lock is on, input lines cannot be selected.

??It is not possible to switch to INT SG when two screens are displayed with the SUB WINDOW function

SDJH

*1 The menu is used to set either YPBPR or VIDEO for the viewfinder input.

&RQWUROVDQG7KHLU)XQFWLRQVFRQWLQXHG

4 0(18)81&7,21EXWWRQV

Use these buttons to display menus, select and adjust settings and confirm menu selections.

??When the control lock is on, the key mark appears and FUNCTION does not operate.

??In 3D assist mode, the item of FUNCTION3 is forcefully fixed to the 2D image adjustment mode item (2D ADJUST).

5 3LFWXUHDQGYROXPHDGMXVWLQJNQREVODPSV

)XQFWLRQVLQ'LPDJHDGMXVWPHQWPRGH

Knob1

Knob2

Knob3

PEAK[PEAKING] 0 - 30 (0) / PHASE 0 - 60 (30) R-GAIN / R-BIAS (page 32)

CHROMA 0 - 60 (30) / F-IN-R (page 46) 0 - 30 (30) G-GAIN / G-BIAS (page 32)

VOLUME 0 - 60 (0) / BRIGHT 0 - 60 (30) / B-GAIN / B-BIAS (page 32)

Knob4 CONT.[CONTRAST] 0 - 60 (50) / B.LIGHT[BACKLIGHT] 0 - 100 (80)

( ) denotes factory preset values.

(Continued on next page)

&RQWUROVDQG7KHLU)XQFWLRQVFRQWLQXHG

)XQFWLRQVLQ'DVVLVWPRGH

MIRROR (MIRROR) / HORIZONTAL (SHIFT) / MODE (CONVERGENCE) / Knob1 SIZE (COLOR) / ZOOM (ZOOM FOCUS) / EXPAND (VERTICAL) /

Knob2

OVERLAY (OVERLAY)

VERTICAL (SHIFT) / MANUAL (CONVERGENCE) /

FOCUS-IN-RED (ZOOM FOCUS) / MARKER1 (VERTICAL) / MARKER (OVERLAY)

Knob3 SPEED (CONVERGENCE) / MARKER2 (VERTICAL)

Knob4 ASSIST FUNCTION (All Functions)

( ): Selected assist function

??These are rotary push knobs. You can press one of the four knobs to display the corresponding assigned function and image adjusting knob status, and then make adjustments.

??The setting value is saved and the indication disappears when you press [ENTER] or when 10 seconds elapses after the setting value is changed.

??If you want to change the function assigned to a knob, press the knob and change the function. The selected function is displayed in green.

??When values are changed from the factory defaults, the LED above the knob (amber) lights.

??Settings are loaded when the monitor is turned on. However, operating changes cannot be made in the following conditions.

??When the control lock is on, the key mark appears and setting values cannot be changed (page 51).

??When the MONO function is ON (page 31), [PHASE] and [CHROMA] operations are disabled.

??F-IN-R is enabled during operation of the FOCUS-IN-RED function.

??While operating HV DELAY (page 41) (when set to any other setting than OFF), [BRIGHT] operation is disabled.

??The ???CONTRAST??? and ???BACK LIGHT??? operations are disabled in BLACK MODE.

*For the operating procedures of adjusting knobs in 3D assist mode, refer to ???3D Assist Mode??? (page 52).

6 7DOO\/DPSV5HGDQG*UHHQ

Can be lit by a control signal (red tally and green tally) from a GPI/camera.

If the red tally and green tally light at the same time, the tally color will become amber.

7Protection Panel

This panel is for protecting the liquid crystal.

??The protection panel can be removed by removing the four screws. When attaching the panel, note that there is no distinction between the back and front and the top and bottom.

8Tilt Stand

The tilt stand allows you tilt the unit 15?? forward or 20?? backward.

When tilting the unit, firmly hold the bottom of the stand and move the top of the unit.

If you want to remove the tilt stand, refer to ???How to Remove the Tilt Stand??? on page 17.

<Note>

When tilting the monitor, be careful not to trap a hand between the monitor and stand.

Can be lit by a control signal from a GPI/ camera.

10 6',+'6'LQSXWWHUPLQDO%1&

This is the SDI1 input terminal. (Compatible with HD/SD automatic switching, Compatible with 3G-SDI)

When you use 3D assist mode (page 51), input images for the left eye (L).

11 6',DFWLYHWKURXJKRXWSXWWHUPLQDO

This terminal outputs SDI1 input as is.

12 6',+'6'LQSXWWHUPLQDO%1&

This is the SDI2 input terminal. (Compatible with HD/SD automatic switching)

When you use 3D assist mode (page 51), input images for the right eye (R).

13 6',DFWLYHWKURXJKRXWSXWWHUPLQDO

This terminal outputs SDI2 input as is.

14 9,'(2<LQSXWWHUPLQDO%1&

This is the VIDEO signal (component signal) input terminal/Y signal (analog component signal) input terminal.

15PB/PRLQSXWWHUPLQDO%1&

This is the PB/PR signal (analog component signal) input terminal.

16 9)WHUPLQDO'68%SLQV

This terminal connects to the VF (viewfinder) terminal of broadcasting and business cameras made by Panasonic.

The unit can be used as the viewfinder for such a camera.

External control is possible by using a GPI signal.

18 6(5,$/WHUPLQDO'68%SLQV

External control is possible by using an RS- 232C interface.

19 +'0,LQSXWWHUPLQDO

This is the HDMI input terminal.

20 '&,1WHUPLQDO;/5SLQV

This is the external DC power supply input terminal.

When a DC power supply is connected concurrently with the battery, the external power input takes precedence.

21 %DWWHU\KROGHU

This holder is used with a battery made by Anton/Bauer. (page 14)

22 6FUHZKROHVIRUIL[LQJWULSRG

There are two screw holes on both the top and bottom for fixing the unit to a tripod (compatible with 3/8-16UNC). A removable adapter is installed in one of the screw holes on the top of the unit, and enables a 1/4-20UNC screw

to fit in the screw hole. Decide whether to use the adapter depending on the diameter of the tripod???s fixing screw. Use a flat-blade screwdriver to remove or install the adapter.

23 6FUHZKROHVIRUPXOWLSXUSRVHIL[LQJ

There are four screw holes (M3) for multi- purpose fixing on the rear of the unit, and two on each the left and right.

6XSSO\LQJWKHSRZHU

An Anton/Bauer battery pack or V-mount type battery pack and external DC power supply can be used to power this unit.

??Batteries for which connection verified

??HYTRON 50

??DIONIC 90

??DIONIC HC

1.Install the Anton/Bauer battery pack.

%DWWHU\SDFN

??Batteries for which connection verified

??ENDURA E-7S

??ENDURA E-HL9

??ENDURA E-10

1.Install the V-mount type adapter plate.

Adapter plate

2.Insert the battery pack and slide it in the direction of the arrow.

5HIHUHQFH!7RUHPRYHWKHEDWWHU\SDFN

Slide it in the opposite direction to the one in which it was attached while keeping the release lever on the battery holder pulled down all the way.

<Reference> To remove the adapter plate

Slide it in the opposite direction to the one in which it was attached while keeping the release lever on the adapter plate pulled down all the way.

<Notes>

??For details on the V-mount type adapter plate, contact the place of purchase.

??When you use a V-mount type adapter plate, the % (percent) indication cannot be displayed even if you use a battery with a battery level display function.

??For details on how to attach the V-mount type battery, see the instruction manual supplied with the battery holder.

6XSSO\LQJWKHSRZHUFRQWLQXHG

8VLQJDQH[WHUQDO'&SRZHUVXSSO\

1.Connect the external DC power supply to the DC IN socket on this unit.

'&,1VRFNHW

External DC

SRZHUVXSSO\

2.Turn ???ON??? the external DC power supply switch. (Where the external DC power supply has a power switch)

3.Turn ???ON??? the POWER switch on this unit.

,IDQH[WHUQDO'&SRZHUVXSSO\LVXVHGWKHQ

FKHFNWKHUDWLQJVRIWKHH[WHUQDO'&SRZHU

VXSSO\VRWKDWWKH\DUHFRPSDWLEOHZLWKWKRVH

RIWKLVXQLW

&KHFNWKHSLQDUUDQJHPHQWVRIWKH'&RXWSXW

WHUPLQDORIWKHH[WHUQDO'&SRZHUVXSSO\DQG

WKRVHRIWKH'&,1VRFNHWRIWKLVXQLWVRWKDW

WKHLUSRODULWLHVDUHFRUUHFWO\DUUDQJHG

,I9DUHVXSSOLHGWRWKHXQLW??V*1'

WHUPLQDOE\PLVWDNHWKLVPD\FDXVHILUHRU

LQMXU\

7KHH[WHUQDO'&SRZHUVXSSO\FDQQRWEH

VXSSOLHGIURPWKH'&RXWSXWWHUPLQDORID

3DQDVRQLFFDPHUDUHFRUGHUEHFDXVHWKHXQLW

UHTXLUHVDFXUUHQWWKDWH[FHHGVWKHRXWSXW

UDWLQJRID3DQDVRQLFFDPHUDUHFRUGHU

'&,1VRFNHW

<Notes>

??Use a shield cable with a length of 2 m (6.56 feet) or less for the DC cord. Use of cords any longer than 2 m (6.56 feet) may result in noise appearing on the screen.

??If the battery pack and an external DC power supply are connected simultaneously, then the external DC power supply will have priority.

If the external DC power supply is used, then the battery pack may be fitted or removed.

??If an external DC power supply is used, then make sure that the external DC power supply is first turned ON, then this unit is turned ON. If they are turned ON in the reverse order, then this unit may malfunction, because the output voltage of the external DC power supply will gradually increase.

??Input voltage that above the specification is not displayed accurately.

9))XQFWLRQ

The unit can be connected to broadcasting and business cameras made by Panasonic and used as a VF (viewfinder). If you want to use the unit as a VF (viewfinder), remove the tilt stand (page 17).

VF cable (Option)

Part number: BT-CS910G

VF connector on unit side

Camera platform*1(commercially available)

Camera side VF terminal

*1 Use a camera platform that can fully withstand the weight of the unit (1.7 kg (3.75 lb)).

<Note>

This unit requires a current that exceeds the output rating of a Panasonic camera-recorder, so the external DC power cannot be supplied from the DC output terminal of a Panasonic camera-recorder.

Do not use the battery pack. If this unit is mounted on the camera-recorder with the battery pack attached, the camera platform may be damaged. Use an external DC power supply.

Contact your vendor for details of broadcasting and business camera-recorders that will be launched in the future.

?? 3DQDVRQLFFDPHUDUHFRUGHUVWKDWDOORZWKHXQLWWREHFRQQHFWHGDVD9)YLHZILQGHU

*1 Configure the menu settings in accordance with the output signal format of the camera (page 48). *2 For the settings, refer to the instruction manual of the camera.

*3 The ZEBRA information can be set for the camera (page 37).

*4 The tally lamp on the rear of the monitor lights in accordance with the REAR TALLY setting (page 37).

How to Remove the Tilt Stand

When you do not want to use the tilt stand such as when using the unit as a VF (viewfinder), remove the tilt stand mounting screw (four screws) with a Phillips driver and then remove the tilt stand from the unit.

When attaching the tilt stand, make sure to align the protrusions for alignment with the corresponding alignment holes.

Alignment hole

<Notes>

??When tilting the monitor, be careful not to trap a hand between the monitor and stand.

??When not using the tilt stand, take care that the unit does not fall over.

??When the unit will be permanently installed in one place, we recommend securing it in place using the screw holes at the bottom of the stand.

2QVFUHHQ'LVSOD\

The screen shows information such as the operating status display, picture adjusting knob status, sharpness display, function display, audio level meter display, time code display, closed caption display, DC power supply voltage and battery level display, and menu display.

2SHUDWLQJVWDWXVGLVSOD\

4 8

7KHVHOHFWHGLQSXWOLQHSDJH

?? SDI1, SDI2, HDMI, VIDEO, YPBPR, VF-YPBPR/VF-VIDEO, INT SG.

6LJQDOIRUPDW

?????UNSUPPORT SIGNAL??? appears if an unsupported signal is input. It may also indicate that the format selected in the ???INPUT SELECT??? menu does not match the input signal.

?????NO SIGNAL??? appears without input signal.

9DULRXVLQGLFDWLRQV3,;(/723,;(/PRGH

?? This indicates the PIXEL TO PIXEL mode is engaged.

9DULRXVLQGLFDWLRQV),/0PRGH

?? This indicates that ???GAMMA SELECT??? of the ???VIDEO CONFIG??? is set to ???FILM.???

9DULRXVLQGLFDWLRQVZDUQLQJRILPSURSHURSHUDWLRQVWDWXVIRUWKHFDPHUDVHWWLQJV

??This indicates there is an improper operation status relative to the camera settings.

??The condition to display differs depending on the type and settings of the camera used in combination with the unit. For details, see the instruction manual of the camera.

9DULRXVGLVSOD\VORFNVHWWLQJ

?? This indicates that the front operations lock is on. (page 51)

'&SRZHUVXSSO\YROWDJHGLVSOD\

?? DC power supply voltage is displayed.

%DWWHU\OHYHOGLVSOD\

??When you are using an Anton/Bauer battery with a battery level display function, the battery level is

LQGLFDWHGE\WKHQXPEHURI??DQGDSHUFHQWDJH:KHQ\RXDUHXVLQJDEDWWHU\RWKHUWKDQWKDWRUWKH$& adapter, the display may not be shown or the battery level may not be indicated correctly. The battery

OHYHOLVLQGLFDWHGE\DQXPHULFDOYDOXHLQLQFUHPHQWV$OVRWKHUHDUHVHYHQ??VHJPHQWVWRLQGLFDWH the battery level, and all seven of them are displayed until the battery level is approximately 70 %. After

WKDWWKHQXPEHURI??LVUHGXFHGE\RQHIRUHDFKUHGXFWLRQLQEDWWHU\SRZHUDQGQRPDUNVDUH displayed when the battery level falls below approximately 10 %.

??The indication can be turned ON/OFF in ???BATTERY REMAIN??? of the ???SYSTEM CONFIG??? menu (page 34).

<Notes>

??The display state of the status can be set in ???STATUS DISPLAY??? of the ???SYSTEM CONFIG??? menu (page 34).

?????UNSUPPORT SIGNAL??? and ???NO SIGNAL??? may not be properly displayed.

??For details on the operation status display in 3D Assist mode, refer to ???3D Assist Mode??? (page 52).

2QVFUHHQ'LVSOD\FRQWLQXHG

3LFWXUHDQGYROXPHDGMXVWLQJNQREVVWDWXVGLVSOD\

3LFWXUHDGMXVWLQJNQRESDJH

??These are rotary push knobs.

??If you press a knob, the setting value state appears at the bottom left, and the item assigned to the corresponding knob is displayed at the bottom right.

??If multiple items are assigned to one knob, you can press the knob to switch items.

??The indication disappears when you press [ENTER] or after 10 seconds of inaction.

??Only adjustments that appear on the screen can be adjusted.

6WDWXVGLVSOD\

The status of an item can be identified by the display color of the item name (page 11, ???Picture and volume adjusting knobs???).

White: An item not target for adjustment.

Green: An item target for adjustment.

Gray: An item which cannot be adjusted.

6KDUSQHVVGLVSOD\

?? Indicates the ???SHARPNESS H/V??? setting value of the ???VIDEO CONFIG??? menu.

?? If no operation is performed for 2 minutes, the setting value is confirmed and the display disappears.

SHARPNESS H 30

)XQFWLRQGLVSOD\

F1:WFM/VECTOR

F2:PIXEL TO PIXEL

F3:FOCUS-IN-RED

XXXXX

??Use the menu to open and set up functions.

??When ???FUNCTION DISPLAY??? (page 39) is set to ON1 or ON2, press any of the ???FUNCTION1??? to ???FUNCTION3??? buttons to display the functions assigned to the FUNCTION buttons.

??In 3D assist mode (page 52), [FUNCTION3] becomes the 2D picture quality adjustment mode button.

??If no operation is performed for 2 seconds, the setting value is confirmed and the display disappears.

?????XXXXX??? indicates operating status (page 41, ???Functions displayed during FUNCTION button operation???).

2QVFUHHQ'LVSOD\FRQWLQXHG

$XGLROHYHOPHWHUGLVSOD\

Peak hold

Overrange

??A color skeleton bar meter indicates the audio level for SDI signals and HDMI signals.

??The display method of the audio level meter can be set in the menu (page 49).

??In 3D assist mode, the audio of the SDI1 (L) side is indicated.

'LVSOD\FRORU

Green: Up to reference point (included)

Yellow: Reference point (not included) to 0 dB point

Red: Overrange

7LPHFRGH7&GLVSOD\

( : ) NDF ( . ) DF

??Use the menu to display the time code for HD-SDI signal input. It also allows you to switch display mode (VITC, LTC, VUB, LUB). (page 50)

,Q9,7&DQG/7&GLVSOD\PRGH

??Displays the time code in hours: minutes:

seconds: or frames.

??In drop-frame mode, a different delimiter between seconds and frames is used.

Note :

Read errors are displayed as ???--:--:--:--???

,Q98%DQG/8%GLVSOD\PRGHV

??BG8, BG7, BG6, BG5, BG4, BG3, BG2, BG1 appear in the stated order.

BG: binary group

??The (:) delimiter does not appear.

Note :

Read errors are displayed as ???--:--:--:--???

2QVFUHHQ'LVSOD\FRQWLQXHG

&ORVHGFDSWLRQ&&GLVSOD\

Closed caption display area

(When the specified window extends out of the entire screen)

??CLOSED CAPTION can be displayed when SDI signals and VIDEO signals are input.

??CLOSED CAPTION complies with the following standards.

??Composite Standard EIA/CEA-608 (VBI)

??SD-SDI CC Standard EIA-608 (ANC)

??HD-SDI CC Standard EIA-708

??In the case of EIA-708, display is possible at a position simultaneously specified for multiple windows (up to 8).

??The display position is within a display area that is located inside the entire screen. (Refer to the following notes.)

??The display settings can be configured in the menus. You can also select the type of CLOSED CAPTION, display channel (EIA/CEA-608), and display service (EIA/CEA-708) in the menus. (page 50)

Notes:

??The specified window position is displayed as a position within the display area depending on the CLOSED CAPTION information.

??The window may extend out of the display area depending on the specified window position and size. In such a case, the window will be displayed but if the window also extends out of the entire screen, the display position of the window will be changed so that the window is displayed inside the entire screen.

'&SRZHUVXSSO\YROWDJHDQGEDWWHU\OHYHOGLVSOD\

DC14.0V 50%

??DC power supply voltage is displayed.

??The battery level display is displayed when the battery you are using is an Anton/Bauer battery with a battery level display function.

??Displayed when the operating status display is not displayed.

??The display can be set in the menus. (page 34)

Notes:

??The DC power voltage and battery level serve as a near end warning indication as they flash when the level falls to the value set in the menu or lower.

Furthermore, when the level drops to less than approximately 10.0 V, the ???END BATTERY??? battery level error is displayed in red, and

the unit performs the shutdown process after approximately 3 seconds have elapsed.

??With some batteries, operation may be stopped by an over discharge function of the battery itself before the battery level error of the unit is displayed.

We recommend replacing the battery as soon as possible.

User Data

You can save and load up to five combinations of menu settings and adjustments made with the picture adjustment knob as user data. You can also return settings and adjustments to their factory defaults. User data include the following settings.

??Menu settings except ???SETUP LOAD/SAVE??? and ???REMOTE in CONTROL??? (including button function settings on the monitor front panel)

??Screen adjustments made with the picture adjusting knob

6DYLQJXVHUGDWD

1.3UHVV>0(18@WRGLVSOD\WKH0$,1PHQX

2.3UHVV> @> @WRVHOHFWWKH??6<67(0&21),*?? PHQXDQGSUHVV>(17(5@

3.3UHVV> @> @WRVHOHFWWKH??6(7836$9(?? VXEPHQXDQGSUHVV>(17(5@

The setting in the sub menu changes to green.

[SYSTEM CONFIG]

Changes to green

4.3UHVV> @> @WRVHOHFWD??86(5??WR??86(5?? ILOHWRVDYHWKHVHWWLQJVWRDQGSUHVV>(17(5@

The following screen appears.

[SETUP SAVE]

USER1

YES

MENU EXIT SEL. ENTER ENTER

5.6HOHFW??<(6??DQGSUHVV>(17(5@

This saves the user data.

6.7RUHWXUQWRWKHSUHYLRXVVFUHHQSUHVV

>0(18@

/RDGLQJXVHUGDWD

1.3UHVV>0(18@WRGLVSOD\WKH0$,1PHQX

2.3UHVV> @> @WRVHOHFWWKH??6<67(0&21),*?? PHQXDQGSUHVV>(17(5@

3.3UHVV> @> @WRVHOHFWWKH??6(783/2$'?? VXEPHQXDQGSUHVV>(17(5@

The setting in the sub menu changes to green.

[SYSTEM CONFIG]

Changes to green

4.3UHVV> @> @WRVHOHFWD??86(5??WR??86(5?? ILOHWRORDGDQGSUHVV>(17(5@

The following screen appears.

??To return to the factory defaults, select ???FACTORY.???

[SETUP LOAD]

USER1

YES

MENU EXIT SEL. ENTER ENTER

5.6HOHFW??<(6??DQGSUHVV>(17(5@

This loads the user data.

6.7RUHWXUQWRWKHSUHYLRXVVFUHHQSUHVV

>0(18@

0DLQ0HQXFRQWLQXHG

??PDUNHU

(Displayed for SD input in 4:3 aspect ratio mode) This marker is displayed as a dotted line.

(Displayed for HD input and SD input in 16:9 ratio mode.) This marker is displayed as a dotted line.

*1 You can adjust the value within the range of 80 % to 100 % in increments of 1 % by pressing [][].

<RXFDQGLVSOD\WKHPDUNHUDQGWKHPDUNHUVLPXOWDQHRXVO\

Simultaneous display example

The section becomes the ???MARKER BACK???.

It controls the background of the marker selected with a 16:9 ratio.

?? &HQWHUPDUNHU

Center marker

This marker is displayed at the center of the screen.

0DLQ0HQXFRQWLQXHG

*4 The following sharpness values are available and the settings for the selected input signal is displayed. Adjustment status during selection appears at the bottom left of the screen.

1)VIDEO system input (VIDEO) (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS

H/V: 0)

2)HD for any other input (the factory defaults are SHARPNESS MODE: HIGH and SHARPNESS H/V: 0).

3)SD for any other input (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS H/V: 0). *5 To use the ???SUB WINDOW??? (page 42) function,

1)Change settings after exiting the ???SUB WINDOW??? function.

2)It is recommended to use ???MODE2??? for handling fast video. *6 ???SCAN??? changes are not reflected in Anamo size display.

IP mode

???MODE1??? performs IP conversion using intra-frame interpolation. This monitor suppresses the delay to within 1 field.

The factory default is ???MODE1???.

???MODE2??? performs IP conversion using intra-field interpolation.

Since interpolation is performed inside each field, this mode is suitable for checking interlace status.

0DLQ0HQXFRQWLQXHG

??*$,1%,$65*%GLUHFWDGMXVWPHQWPRGH

If you press [ENTER] when the [GAIN] or [BIAS] item is selected in the WHITE BALANCE VAR (1 to 3) menu, the screen switches to the one below and you can use the picture adjusting knobs to directly adjust the RGB while checking the picture.

R is assigned to knob 1, G to knob 2, and B to knob 3.

If ???WHITE BALANCE??? is assigned to FUNCTION1 to FUNCTION3, this mode can also be accessed from the FUNCTION buttons.

??You can switch between GAIN and BIAS by pressing the corresponding knob.

??If you press [ENTER] in the [GAIN] menu, GAIN adjustment is displayed first.

??If you press [ENTER] in the [BIAS] menu, BIAS adjustment is displayed first.

??When you access the mode from a FUNCTION

?? Press the [MENU] button to return to menu display. *1

?? If you switched the mode with a FUNCTION button, display disappears if you press the FUNCTION button. *1

*1 The same operation is also performed after 10 seconds of inaction.

6(5,$/7HUPLQDO3

0DLQ0HQXFRQWLQXHG

*5 The factory preset setting value varies depending on the area set in ???AREA SETTING???. *6 ITU-709 indicates the ITU-R BT.709 standard.

??CALIBRATION

The CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness values and internal monitor processing handles CALIBRATION.

CALIBRATION does not rely on image quality settings since internal signals are used for a calibration. CALIBRATION in this unit is made at D65 color temperature and other color temperatures are results calculated automatically from this value.

??(TXLSPHQWUHTXLUHGIRUFDOLEUDWLRQ

?? Konica Minolta CA-210

or CA-310 display color analyzer

?? Konica Minolta CA- PU12 or CA-PU15

standard measurement probe

?? A RS-232C cable (male to male, straight)

Connect the SERIAL terminal on this unit to the RS- 232C terminal on the display color analyzer using a straight cable.

This unit

Konica Minolta CA-PU12 or CA-PU15 standard measurement probe

Konica Minolta CA-210 or CA-310 display color analyzer

RS-232C cable

(Continued on next page)

0DLQ0HQXFRQWLQXHG

?? Make the room dark so that no external light can enter the standard measurement probe before starting the calibration. If external light enters the probe, the low brightness characteristics may not be calibrated correctly.

?? LCD panel characteristics and instrument error in the display color analyzer may sometimes result in small differences in values after calibration.

In a fine tuning of the monitor, also set GAIN and BIAS for R, G and B in the COLOR TEMP. VAR mode. ?? Do not apply the probe to a WFM/VECTOR display on the screen.

??CALIBRATION

Select CALIBRATION in the ???SYSTEM CONFIG??? menu to open the following menus.

*1 ???EXECUTING??? is displayed during ???AUTO CALIBRATION??? and ???COMPLETE??? appears when calibration ends. ???INCOMPLETE??? appears if calibration could not be completed.

*2 When ???RESET??? ends, ???COMPLETE??? appears.

3HUIRUPLQJ$872&$/,%5$7,21

1.3UHVV> @> @LQWKH??6<67(0&21),*?? PHQXVHOHFWWKH>&$/,%5$7,21@VXEPHQX DQGSUHVV>(17(5@

2.3UHVV> @> @VHOHFWWKH>$872 &$/,%5$7,21@VXEPHQXDQGSUHVV>(17(5@

[AUTO CALIBRATION]

YES

MENU EXIT SEL. ENTER ENTER

3.6HOHFW??<(6??DQGSUHVV>(17(5@

This starts calibration.

[AUTO CALIBRATION]

xxxxxxxx

MENU EXIT SEL. ENTER ENTER

xxxxxxxxx indicates that one of the following messages with the meaning listed below appears.

EXECUTING: Operation in progress

COMPLETE: Operation completed

INCOMPLETE: Operation incompleted. (Check the SERIAL connection or display color analyzer connection.)

4.7XUQWKHSRZHURIIDQGWKHQRQDIWHU

SHUIRUPLQJDXWRFDOLEUDWLRQ

0DLQ0HQXFRQWLQXHG

RESET operation

1.3UHVV> @> @LQWKH??6<67(0&21),*?? PHQXVHOHFWWKH>&$/,%5$7,21@VXEPHQX DQGSUHVV>(17(5@

2.3UHVV> @> @VHOHFWWKH>5(6(7@VXEPHQX DQGSUHVV>(17(5@

[RESET]

YES

MENU EXIT SEL. ENTER ENTER

3.6HOHFW??<(6??DQGSUHVV>(17(5@

This starts calibration.

[RESET]

xxxxxxxx

MENU EXIT SEL. ENTER ENTER

xxxxxxxxx indicates that the following message with the meaning listed below appears.

COMPLETE: Operation completed

4.7XUQWKHSRZHURIIDQGWKHQRQDIWHU

SHUIRUPLQJDXWRFDOLEUDWLRQ

VF CONFIG

?? The priority sequence for GPI control and SERIAL is as follows: GPI > VF CONFIG > SERIAL.

0DLQ0HQXFRQWLQXHG

??If a FUNCTION button is pushed during the picture adjusting knobs display, the picture adjusting knobs display will be cancelled and the FUNCTION operation cannot be executed.

*1 The settings are cancelled when the power is turned OFF.

*2 If these settings are changed, the menu settings will also change. *3 The control settings do not operate during GPI operation.

*5 During FOCUS-IN-RED operation, the detection sensitivity can be changed with the F-IN-R knob. The setting range is from 0 to 30, with a higher numerical value resulting in higher detection sensitivity (the focus becomes worse).

*6 Only enabled when TALLY control from the camera or GPI (R-TALLY) is ON.

*7 The bright picture more than 75 % is clipped. The back light and contrast cannot be adjusted. *8 The operating status is displayed regardless of the ON/OFF setting.

*9 The function displayed with the ON2 setting can be operated with a button only during the time that it is displayed.

0DLQ0HQXFRQWLQXHG

??)XQFWLRQVGLVSOD\HGGXULQJ)81&7,21EXWWRQRSHUDWLRQ

Pressing any of the [FUNCTION1] to [FUNCTION3] buttons displays the operations assigned to each button as shown below.

??HV DELAY

DELAY OFF/H DELAY/V DELAY/

HV DELAY

??BLUE ONLY

BLUE ONLY ON/BLUE ONLY OFF

??GAMMA SELECT

GAMMA STANDARD/GAMMA FILM/

GAMMA STDIO/PST

??SD ASPECT 4:3/16:9

??SCAN

NORMAL SCAN/UNDER SCAN

??SUB WINDOW

SINGLE/FULL/PART/STILL

??WFM/VECTOR

WFM/VECTOR OFF/WFM Y ON/

WFM R ON/WFM G ON/WFM B ON/

9(&725??9(&725??69(&725??

9(&725??9(&725??

??MARKER

MARKER OFF/4:3 MARKER/ 13:9 MARKER/14:9 MARKER/ CNSCO2.39 MARKER/ CNSCO2.35 MARKER/

2:1 MARKER/VISTA MARKER/ 95% MARKER/93% MARKER/ 90% MARKER/88% MARKER/ 80% MARKER/

xx% MARKER (xx % is a USER setting value of 80 % to 100 %)/MARKER ON

??When the setting values of both 16:9 and 4:3 are set to other than OFF in the MARKER menu settings, the setting value of 16:9 is displayed in the first half section, and the setting value of 4:3 is displayed in the second half section.

??PIXEL TO PIXEL

PIXEL TO PIXEL OFF/

PIXEL TO PIXEL CENTER/

PIXEL TO PIXEL LT/

PIXEL TO PIXEL RT/

PIXEL TO PIXEL RB/

PIXEL TO PIXEL LB

??PIXEL POSITION

PIXEL TO PIXEL OFF/

PIXEL TO PIXEL CENTER/

PIXEL TO PIXEL LT/

PIXEL TO PIXEL RT/

PIXEL TO PIXEL RB/

PIXEL TO PIXEL LB

??FOCUS-IN-RED

FOCUS-IN-RED OFF/FOCUS-IN-RED ON

??ZEBRA

ZEBRA OFF/ZEBRA ON

??REAR TALLY

REAR TALLY OFF/ REAR TALLY ON

??LEVEL METER

METER OFF/METER 2CH/METER 4CH/

METER 8CH

??CROSS HATCH

CROSS HATCH HIGH/

CROSS HATCH LOW/

CROSS HATCH OFF

??MONO

MONO ON/MONO OFF

??TIME CODE

LTC/VITC/LUB/VUB/TC OFF

??BLACK MODE

BLACK MODE OFF/BLACK MODE ON

??CLOSED CAPTION CC1/CC2/CC3/CC4/CC OFF (SRV1/SRV2/SRV3/SRV4/SRV5/ SRV6/CC OFF)

*The displayed items differ depending on the selection for CC TYPE.

??2D ADJUST

2D ADJUST OFF/2D ADJUST ON

<Note>

WHITE BALANCE is switched to adjustment mode with a FUNCTION button, and the indication that indicates the operation is not displayed.

????+9'(/$<??

This displays the blanking period. Each press of the button changes the display as follows: H blanking

GLVSOD\ 9EODQNLQJGLVSOD\ +DQG9EODQNLQJGLVSOD\ QREODQNLQJGLVSOD\

0DLQ0HQXFRQWLQXHG

????68%:,1'2:??

Opening the ???SUB WINDOW??? function splits the screen (main window) in two as shown below to enable comparison of a recorded still image with live video.

Use the ???SUB WINDOW??? setting (FULL, PART) in the ???SYSTEM CONFIG??? menu (page 34) to set up the function as shown below.

Press the button ([FUNCTION1] to [FUNCTION3] (page 38)) to which the ???SUB WINDOW??? function has been assigned to turn the function on and off.

??This assumes that the ???SUB WINDOW??? function has been assigned to any of the [FUNCTION1] to [FUNCTION3] buttons.

To setup ???I-P MODE??? (page 31), exit the ???SUB WINDOW??? function first.

??FULL

Resizes the main window to also display a second window (two sub-windows).

Press the FUNCTION button to which the SUB WINDOW function has been assigned.

??PART

Resizes the main window to show only its center to also display a second image (two sub-windows).

Press the FUNCTION button to which the SUB WINDOW function has been assigned.

(Left side is stored in memory.)

These examples show 16:9 aspect ratio images.

Note on FULL/PART selection

This function is designed to enable comparison of identical formats input to the same input terminal. Input of different formats via different input channels may distort the sub-window (left side, still image) or blanking could occur. However, input of an identical format signal to the input terminal during still image acquisition will display correctly.

0DLQ0HQXFRQWLQXHG

????:)09(&725??

The ???WFM/VECTOR??? function enables display of the waveform and vector display. Use ???DISPLAY SETUP??? in the main menu to select ???WFM??? and ???VECTOR??? display. (page 50)

Press the button ([FUNCTION1] to [FUNCTION3] (page 39)) to which the ???WFM/VECTOR??? function has

been assigned to switch the display in the following order.

:)09(&7252)) :)0<21 :)0521 :)0*21 :)0%21 9(&725[WR[

??This assumes that the ???WFM/VECTOR??? function has been assigned to any of the [FUNCTION1] to [FUNCTION3] buttons.

WFM is displayed in the order of the Y signal, R signal, G signal, and B signal.

Press the FUNCTION button to which the WFM/VECTOR function has been assigned.

These examples show 16:9 aspect ratio images.

*1 Displayed only for SDI signal input.

?? The scale display is as shown below.

0DLQ0HQXFRQWLQXHG

????3,;(/723,;(/??DQG??3,;(/326,7,21??

The ???PIXEL TO PIXEL??? function allows you to check images at their actual pixel resolution (1080i/p signals only).

Press the button ([FUNCTION1] to [FUNCTION3] (page 38)) to which the ???PIXEL TO PIXEL??? function has been assigned to turn the function on. Then press the button ([FUNCTION1] to [FUNCTION3] (page 38)) to which the ???PIXEL POSITION??? function has been assigned to position the display of signals.

??This assumes that the ???PIXEL TO PIXEL??? and ???PIXEL POSITION??? functions have been assigned to any of the [FUNCTION1] to [FUNCTION3] buttons.

The underlined values are factory preset setting values.

*1 The following settings are disabled in PIXEL TO PIXEL mode.

??Setting ???ANAMO??? to ???ON???, and setting ???SCAN??? to ???UNDER??? in ???VIDEO CONFIG???

??Any ???HV DELAY??? setting in ???FUNCTION???

?????MARKER??? display

*2 Enabled during ???SDI1???, ???SDI2???, ???HDMI???, ???YPBPR??? and ???VF (VF-YPBPR)??? input.

?? ??3,;(/326,7,21??GLVSOD\SRVLWLRQVHTXHQFH

PIXEL POSITION: c d e f g c .....

0DLQ0HQXFRQWLQXHG

????&5266+$7&+??

If the CROSS HATCH function is used, markers are displayed at regular vertical and horizontal intervals to facilitate, for example, easy composition. The marker line width is 1 dot /1 line and the interval is 80 dots/80 lines or 40 dots/40 lines depending on the ???SIZE??? setting in the MARKER menu (page 27).

Each press of the button (???FUNCTION1??? to ???FUNCTION3??? (page 38)) to which the ???CROSS HATCH??? has been assigned turns the function on and off.

??This assumes that the ???CROSS HATCH??? function has been assigned to any of the [FUNCTION1] to [FUNCTION3] buttons.

(DFKSUHVVRIWKH)81&7,21EXWWRQWRZKLFKWKH??&5266+$7&+??IXQFWLRQLVDVVLJQHGFKDQJHV WKHGLVSOD\DVVKRZQ

HD/SD (16:9) mode

3UHVVWKHEXWWRQDJDLQEDFNWRRULJLQDOLPDJHZLWKRXWFURVVKDWFK

0DLQ0HQXFRQWLQXHG

????)2&86,15('??

When the ???FOCUS-IN-RED??? function is used, the section that is being focused is displayed in an easy-to- understand red, making camera focus adjustments easy.

Each press of the button (???FUNCTION1??? to ???FUNCTION3??? (page 38)) to which the ???FOCUS-IN-RED??? has been assigned turns the function on and off.

??This assumes that the ???FOCUS-IN-RED??? function has been assigned to any of the [FUNCTION1] to [FUNCTION3] buttons.

When the ???FOCUS-IN-RED??? function is displayed, the detection sensitivity level (0 - 30) can be changed with the F-IN-R knob. A higher numerical value results in lower detection sensitivity (outlines are displayed in red even when they are not in focus properly).

If you set CHROMA to 0 or assign "MONO" to another function button to switch to monochrome, the focus will become easier to check.

3XVKRQFHWKH)81&7,21EXWWRQWRZKLFKWKH

)2&86,15('IXQFWLRQLVDVVLJQHG

Press the

EXWWRQDJDLQ

The foreground is in focus

The outlines in focus are displayed in red

Press the

EXWWRQDJDLQ

The background is in focus

These examples show 16:9 aspect ratio images.

0DLQ0HQXFRQWLQXHG

AUDIO

Set the audio output and audio level meter.

The underlined values are factory preset setting values.

*1 If the input signal is SD when CH5 to CH8 is selected:

7KHFKDQQHOFDQEHVZLWFKHGIURP&+ &+&+ &+&+ &+DQG&+ &+7KHPHQX settings remain as is.)

*2 When an HDMI signal is input, the audio of CH1 is output to the headphones (L) regardless of the menu setting.

*3 When an HDMI signal is input, the audio of CH2 is output to the headphones (R) regardless of the menu setting.

*4 When an HDMI signal is input, the display becomes 2CH regardless of the menu setting. When an SD- SDI signal is input, the display becomes 4CH even if 8CH is selected in the menu.

*5 The factory preset setting value varies depending on the area set in ???AREA SETTING??? (page 35).

Adjusting knob 1 - 4

OFF

MIRROR

???

MIRR ??? FUNC.

3D Assist Mode

The unit is equipped with 3D assist mode to provide support for shooting with a rig-type 3D camera system. The 3D assist mode has the following functions.

??,PDJHLQSXWPHWKRG6,08/7$1(286VLPXOWDQHRXVPHWKRG5

Two types of image, one for the left eye (L) and one for the right eye (R), are input to the two SDI1 and SDI2 terminals.

??In 3D assist mode, the input is fixed to SDI1/SDI2 and the input line cannot be changed.

??An appropriate phase difference with the input signal of SDI2 is one that is up to ??15 ??s using the input signal of SDI1 as the reference.

??If the input signal formats of SDI1 and SDI2 are not identical or only one of the signals is input, the screen display will black out.

??$VVLVWIXQFWLRQV

2 Indicates the format of the signal input to SDI1.

3 Indicates the format of the signal input to SDI2.

4 Indicates the functions assigned to adjusting knobs 1 to 4. For the functions assigned to adjusting knobs 1 to 3, the definitions vary by assist function. The setting value of each function is confirmed at the point in time when the corresponding adjusting knob is operated. (pages 54 to 58)

When you switch the mode to 3D assist mode, statuses 1 to 3 are displayed.

When you operate the function of 4 : If you press one of the adjusting knobs 1 to 4, statuses 1 to disappear and status 4 is displayed. Status 4 continues to be displayed until the operation ends.

When you end the operation of 4 : If you press the FUNCTION3 button, status 4 disappears and statuses 1 to 3 are displayed.

3D Assist ModeFRQWLQXHG

<Note>

??When a signal on which the LR information is superimposed is input to SDI1 such as when there is an AG-3DA1 connection, that LR information is displayed on the right side of the signal format. If L and R are incorrectly input, the LR information is displayed in yellow. If the LR information is input to SDI2 only, the LR information is not displayed on the right side of the signal format.

??+RZWRVZLWFKWKHDVVLVWIXQFWLRQ

Turn adjusting knob 4 (rightmost knob). Each turn clockwise switches the assist function in the order shown in the table above.

<Notes>

??When you switch to 3D assist mode, dedicated functions are assigned to the picture adjusting knobs and FUNCTION3 button in the control section on the front panel.

??When you want to make picture adjustments, switch to 2D mode.

??To make picture adjustments while still in 3D assist mode, press the FUNCTION3 button to turn ON the 2D picture quality adjustment mode, and then switch the function of the adjusting knob to the 3D assist mode function.

(If you turn OFF the 2D picture quality adjustment mode (2D ADJUST), the adjusting knob is reset to the 3D assist mode function.)

??The setting value is saved and the mode is returned to 3D assist mode when you press [ENTER] or when 10 seconds elapses after the setting value is changed.

??+RZWRUHWXUQWR'PRGH

Select [2D] in "2D/3D ASSIST??? of the main menu.

3D Assist ModeFRQWLQXHG

0,5525/HIW5LJKWDQG7RS%RWWRPLQYHUVLRQ

This function inverts just the left and right or top and bottom or both the left and right and top and bottom of the input signals of SDI2 (R) to enable the basic adjustments of a rig-type 3D camera system (half mirror type) to be made.

Screen:

The L/R 2 screens are shown side-by-side.

<Notes>

??Left and right inversion and top and bottom inversion are also reflected in other assist functions.

??The inversion setting information is even saved when the power is turned off.

The underlined values are factory preset setting values.

6+,)7+RUL]RQWDODQG9HUWLFDO6KLIW

This function shifts the images of SDI2 (R) horizontally or vertically to enable you to overlay the images. You can check the lens axis of a rig-type camera system while checking the rotation offset of the image.

&203$5,621&RPSRVLWLRQ&KHFN

This function is for checking when the subject is captured with only the camera of one side.

Screen:

The L/R 2 screens are shown side-by-side, and a 70% size half-tone marker is shown inside each of the images.

If there is an image shown on either only the left or right, discomfort will be felt and stereoscopic vision will become difficult when the mode is set to 3D.

Perform a comparison check of the parts of the images outside of the markers.

3D Assist ModeFRQWLQXHG

&219(5*(1&(&RQYHUJHQFH&KHFN

This function is for checking the subject???s position at a fixed screen position in order to determine the depth position of the main subject.

Automatically or manually switch the SDI1 (L) image and SDI2 (R) image and then check the subject???s position.

Screen:

Normal display of one screen

??The place at which the image does not change is the convergence point.

??If the camera adjustment (vertical or rotation direction position adjustment) is correct, the image at other than the convergence point will shift to the left/right target.

The underlined values are factory preset setting values.

&2/25&RORU&KHFN

This function overlays and displays the SDI1 (L) image and SDI2 (R) image on a checkerboard pattern in one screen to enable you to check the brightness offset and color differences

3D Assist ModeFRQWLQXHG

9(57,&$/9HUWLFDO2IIVHW&KHFN

This function enables you to operate two horizontal line markers to check the number of lines between markers in the displayed image and check vertical offset, which tends to cause eye fatigue.

??The number of lines of the displayed image is measured and then the number of lines between the two horizontal line markers is displayed at the bottom left of the screen.

Screen:

The L/R 2 screens are shown side-by-side, and two markers are shown.

??Displaying horizontal line markers makes it easy to check the left/right vertical offset.

??If the vertical offset becomes large, discomfort will be felt and stereoscopic vision will become difficult when the mode is set to 3D so make adjustments trying your hardest to eliminate camera vertical offset.

The underlined values are factory preset setting values.

indicated.

3D Assist ModeFRQWLQXHG

29(5/$<3DUDOOD[&KHFN

This function displays vertical line markers to enable you to check the width of parallax.

Overlay display

Gray display

Screen:

L/R images are overlaid and shown on one screen, and vertical line markers are shown at 3% intervals across the horizontal image width.

??Vertical line markers can also be displayed in a gray screen in which the parallax portion is emphasized (gray display).

If the parallax is way too large, stereoscopic vision will become difficult when 3D images are viewed so check the width of parallax of the L side and R side images, using the width of the vertical line markers as a reference.

REMOTE SpecificationsFRQWLQXHG

*3 When ???R-TALLY??? and ???G-TALLY??? simultaneously go on, the tally color changes to orange. *4 When remote standby is set to ON, the CONT. and B.LIGHT LEDs on the front flash.

*5 If the GPI terminal to be assigned is set to a short-circuited state first and then MENU is operated to set this item, the backlight turns off and the screen display disappears, so MENU operation becomes unable to be checked. To change the setting of this item, be sure to set it when the GPI terminal is in the open state.

Restrictions

??SD ASPECT does not operate when the input signal is HD.

??The MARKER items do not operate when the input line of the signal is VF.

??SD ASPECT, SCAN, WFM/VECTOR, MARKER, PIXEL TO PIXEL, and PIXEL POSITION do not operate in SUB WINDOW mode.

??SCAN and MARKER do not operate in PIXEL TO PIXEL mode.

??GAMMA SELECT, SD ASPECT, SCAN, MARKER, and MONO do not operate when the input line of the signal is HDMI and the signal format is 640 x 480.

??3ULRULW\RIDVVLJQHGIXQFWLRQV

??When both ???MARKER1??? and ???MARKER2??? are activated at the same time, ???MARKER1??? has priority. However, when the display aspect ratio is 4:3, the ???MARKER1??? aspect ratio is 16:9 and the ???MARKER2??? aspect ratio is 4:3, ???MARKER2??? is displayed. In this case, the ???MARKER2??? background is controlled.

??When ???MARKER BACK HALF??? and ???MARKER BACK BLACK??? are activated at the same time, ???MARKER BACK BLACK??? has priority.

??INPUT SEL. are prioritized in the order of ???INPUT SEL. VIDEO,??? ???INPUT SEL. SDI1,??? ???INPUT SEL. SDI2,??? ???INPUT SEL. HDMI,??? ???INPUT SEL. YPBPR,??? ???INPUT SEL. VF,??? and ???INT SG.???

??When ???GAMMA SEL. FILM??? and ???GAMMA SEL. STDIO/PST??? are activated at the same time, ???GAMMA SEL. FILM??? has priority.

REMOTE SpecificationsFRQWLQXHG

SERIAL terminal

External operations can be performed via the RS-232C interface.

The following diagram and the table on the following SERIAL terminal pin arrangement and connections. For details on systems using SERIAL, be sure to consult your dealer.

??&RQQHFWRUVDQGVLJQDOV

&RQQHFWRU'68%SLQIHPDOH

6LJQDO

?? &RPPXQLFDWLRQSDUDPHWHUV

?? Command format

STX (02h) Command : Data ETX (03h)

??The command is the 3-character string starting with STX and ending with ETX.

??Append any data after the colon (:) following the command, as required.

??Response formats

ER001: Invalid command

ER002: Parameter error

(UURUDQG:DUQLQJ'LVSOD\V

If for any reason an error occurs in this monitor, the LEDs above the picture adjusting knob flash at 1 second intervals to inform of the error/warning.

*1 Set the BATTERY REMAIN menu item of the SYSTEM CONFIG menu to ON.

*2 The condition to display differs depending on the type and settings of the camera used in combination with the unit. For details, see the instruction manual of the camera.

Maintenance

??To clean the cabinet or surface of the liquid crystal protection panel, gently wipe with a soft, dry cloth.

If the surfaces are extremely dirty, use a soft cloth dipped in a weak detergent solution and then wrung-out to clean the surfaces, then use a dry cloth to finish. Water or similar substances getting inside the monitor can cause a malfunction.

??Never use alcohol, thinner or benzene to clean this unit.

Doing so would cause the surface of the monitor to become discolored, and cause paint to peel.

??Do not spray cleansers directly onto the monitor.

Water or similar substances getting inside the monitor can cause a malfunction.

,QIRUPDWLRQRQ'LVSRVDOIRU8VHUVRI:DVWH(OHFWULFDO (OHFWURQLF(TXLSPHQWSULYDWHKRXVHKROGV

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product.

Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

)RUEXVLQHVVXVHUVLQWKH(XURSHDQ8QLRQ

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

,QIRUPDWLRQRQ'LVSRVDOLQRWKHU&RXQWULHVRXWVLGHWKH(XURSHDQ8QLRQ

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

?? 2011