1 GettingStarted

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR BACK) NO

USER-SERVICEABLE PARTS INSIDE REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle

is intended to alert the user to the presence of uninsulated dangerous voltage within the product???s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer???s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer???s instruction has been adhered to.

Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner???s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service centre. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and

the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

NOTICE: For safety marking information including product identification and supply ratings, please refer to the main label on the bottom or rear of the apparatus.

CAUTION: Only use the AC adapter supplied with this device. Do not use a power supply from another device or another manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.

4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

1 GettingStarted

1 GettingStarted

4 Getting Started

Important Notice for TV colour system

The colour system of this player differs according to currently playing discs.

For example, when the player plays the disc recorded in the NTSC colour system, the image is output as an NTSC signal.

Only the multi system colour TV can receive all signals output from the player.

yy If you have a PAL colour system TV, you will see just distorted images when using discs or video contents recorded in NTSC.

yy The multi system colour TV changes the colour system automatically according to input signals. In case that the colour system is not changed automatically, turn it off and then on to see normal images on screen.

yy Even if the disc recorded in NTSC colour system are well displayed on your TV, these may not be recorded correctly on your recorder.

>>Caution

yy Watching a 3D content for a long period time may cause dizziness or tiredness.

yy It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman.

yy If you are experiencing headache, tiredness or dizziness while viewing content in 3D,

it is strongly recommended to stop the playback and rest until you feel normal.

1 GettingStarted

Table of Contents

1Getting Started

2Safety Information

8 Introduction

8?????? Playable discs and symbols used in this manual

9?????? About the ???7??? symbol display

9?????? Compatibility notes

10?????? File requirement

11?????? AVCHD (Advanced Video Codec High Definition)

12?????? Certain system requirements

12?????? Regional code

12?????? System select

13Remote control

14Front panel

14 Rear panel

2 Connecting

15Connecting the AC adapter

15Connecting to your TV

16?????? What is SIMPLINK?

17?????? Resolution setting

18Connecting to an amplifier

18?????? Connecting to an amplifier via HDMI output

19?????? Connecting to an amplifier via digital audio output

20Connecting to your home network

20 ?????? Wired network connection

20 ?????? Wired network setup

23 USB device connection

23 ?????? Playback content in the USB device

3 System Setting

24 Settings

24?????? Initial Setup

25?????? Adjust the setup settings

25?????? [DISPLAY] Menu

27?????? [LANGUAGE] Menu

27?????? [AUDIO] Menu

29?????? [LOCK] Menu

30?????? [NETWORK] Menu

30?????? [OTHERS] Menu

4 Operating

32 General Playback

32?????? Using [HOME] menu

32?????? Playing a disc

32?????? Playing a file on disc/USB device

33?????? Playing Blu-ray 3D disc

33?????? Enjoying BD-Live???

34?????? Basic operations for video and audio content

34?????? Basic operations for photo content

34?????? Using the disc menu

35?????? Resume playback

35?????? Last scene memory

35Advanced Playback

35?????? Repeat playback

36?????? Repeating a specific portion

36?????? Viewing content information

36?????? Changing content list view

37?????? Selecting a subtitle file

37?????? Options while viewing a photo

38?????? Listening to music while slide show

38On-screen display

38?????? Displaying content information on- screen

39?????? Playing from selected time

39?????? Selecting a subtitle language

40?????? Hearing a different audio

40?????? Watching from a different angle

40?????? Changing the TV Aspect Ratio

41?????? Changing subtitle Code Page

41?????? Changing the Picture Mode

42Using the Premium

5 Troubleshooting

43Troubleshooting

43?????? General

44?????? Network

45?????? Picture

45 ?????? Customer support

45 ?????? Open source software notice

6 Appendix

46Controlling a TV with the supplied remote control

46?????? Setting up the remote to control your

TV

47Network software update

47 ?????? Network update notification

47 ?????? Software update

49Area code list

50Language code list

51Trademarks and licenses

53Audio output specifications

55Specifications

56Maintenance

56?????? Handling the unit

56?????? Notes on discs

57Important information relating to network services

1

2

3

4

5

6

1 GettingStarted

8 Getting Started

Introduction

Playable discs and symbols used in this manual

,,Note

yy Depending on the conditions of the recording equipment or the CD-R/RW (or DVD??R/RW) disc itself, some CD-R/RW (or DVD??R/RW) discs cannot be played on the unit.

yy Depending on the recording software & the finalization, some recorded discs (CD-R/RW, DVD??R/RW, BD-R/RE) may not be playable.

yy BD-R/RE, DVD??R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player???s lens.

yy If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

yy This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality.

yy Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-existing conditions to ensure compatible playback.

yy Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

yy You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista)

About the ???7??? symbol display

???7??? may appear on your TV display during operation and indicates that the function explained in this owner???s manual is not available on that specific media.

Compatibility notes

yy Because BD-ROM is a new format, certain disc, digital connection and other compatibility issues are possible. If you experience compatibility problems, please contact an authorized Customer Service Center.

yy This unit allows you to enjoy functions such as picture-in-picture, secondary audio and Virtual packages, etc., with BD-ROM supporting BONUSVIEW (BD-ROM version 2 Profile 1 version 1.1). Secondary video and audio can be played from a disc compatible with the picture-in- picture function. For the playback method, refer to the instructions in the disc.

yy Viewing high-definition content and up- converting standard DVD content may require a HDMI-capable input or HDCP-capable DVI input on your display device.

yy Some BD-ROM and DVD discs may restrict the use of some operation commands or features.

yy Dolby TrueHD, Dolby Digital Plus and DTS-HD are supported with maximum 7.1 channels if you use HDMI connection for the audio output of the unit.

yy You can use a USB device to store some disc related information, including downloaded on- line content. The disc you are using will control how long this information is retained.

1 GettingStarted

1 GettingStarted

10 Getting Started

File requirement

Movie files

Music files

Photo files

,,Note

yy The file name is limited to 180 characters.

yy Maximum files/Folder: Less than 2000 (total number of files and folders)

yy Depending on the size and number of the files, it may take several minutes to read the contents on the media.

yy The file requirements on page 10 are not always compatible. There may have some restrictions by file features.

yy This unit cannot support the ID3 Tag embedded MP3 file.

yy The total playback time of audio file indicated on the screen may not correct for VBR files.

yy HD movie files contained on the CD/DVD or USB 1.0/1.1 may not played properly. Blu-ray Disc or USB 2.0 are recommended to play back HD movie files.

yy This player supports H.264/MPEG-4 AVC profile Main, High at Level 4.1. For a file with higher level, the warning message will appear on the screen.

yy This player does not support files that are recorded with GMC*1 or Qpel*2.

*1 GMC ??? Global Motion Compensation

*2 Qpel ??? Quarter pixel

,,Note

yy A ???avi??? file which is encoded ???WMV 9 codec??? is not supported.

yy This player supports UTF-8 files even it contains Unicode subtitle contents. This player can not support the pure Unicode subtitle files.

yy Depending on the types of file or ways of recording, it may not play back.

yy A disc which was recorded by multi-session on normal PC is not supported on this player.

yy To be playback a movie file, movie file name and Subtitle file name must be the same.

yy If video codec is MPEG2 TS or MPEG2 PS, subtitle does not play back.

yy The total playback time of music file indicated on the screen may not correct for VBR files.

AVCHD (Advanced Video

Codec High Definition)

yy This player can playback AVCHD format discs. These discs are normally recorded and used in camcorders.

yy The AVCHD format is a high definition digital video camera format.

yy The MPEG-4 AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format.

yy This player can playback AVCHD discs using ???x.v.Colour??? format.

yy Some AVCHD format discs may not play depending on the recording condition.

yy AVCHD format discs need to be finalized.

yy ???x.v.Colour??? offers a wider colour range than normal DVD camcorder discs.

1 GettingStarted

1 GettingStarted

Certain system requirements

For high definition video playback:

yy High definition display that has HDMI input jack. yy BD-ROM disc with high definition content.

yy HDMI or HDCP capable DVI input on your display device is required for some content (as specified by disc authors).

For Dolby?? Digital Plus, Dolby TrueHD and DTS-HD multi-channel audio playback:

yy An amplifier/receiver with a built-in (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD) decoder.

yy Main, center, surround speakers and subwoofer as necessary for chosen format.

Regional code

This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labelled same as the rear of the unit or ???ALL???.

System select

Open the disc tray using the B(OPEN/CLOSE) button and then, press and hold M(PAUSE) for more than five seconds to change the color system (PAL /NTSC /AUTO).

Remote control

Battery installation

Remove the battery cover on the rear of the Remote Control, and insert the R03 (size AAA) battery with 4and 5matched correctly.

1(POWER): Switches the player ON or OFF.

B(OPEN/CLOSE): Opens and closes the disc tray.

0-9 numerical buttons: Selects numbered options in a menu.

CLEAR: Removes a number when setting the password.

TV Control Buttons: See page 46.

c/v(SCAN): Searches backward or forward.

C/V(SKIP): Goes to the next or previous chapter / track / file.

M(PAUSE): Pauses playback.

z(PLAY): Starts playback.

Z(STOP): Stops playback.

HOME (n): Displays or exits the [Home Menu].

INFO/MENU (m): Displays or exits On-Screen Display.

Direction buttons: Selects an option in the menu.

ENTER (b): Acknowledges menu selection.

BACK (1): Exits the menu or returns to the previous screen.

DISC MENU: Accesses menu on a disc.

REPEAT (h): Repeats a desired section or sequence.

AUDIO ([): Selects an audio language.

SUBTITLE (]): Selects a subtitle language.

TITLE/POP-UP: Displays the DVD title menu or BD-ROM???s pop-up menu, if available.

Colored (R, G, Y, B) buttons:

Use to navigate BD-ROM menus. They are also used for [MOVIE], [PHOTO], [MUSIC] and [Premium] menu.

1 GettingStarted

Connecting the AC adapter

Connect the unit to the power supply with the supplied AC adapter.

Rear of the unit

Plug into a power source.

yy Contact an electrical parts distributor for assistance in selecting a suitable AC plug adapteror AC cord set.

yy This AC adapter is manufactured by APD Group Yang Ming Industrial.

>>Caution

Only use the AC adapter supplied with this device. Do not use a power supply from another device or manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.

Connecting to your TV

If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High Speed HDMI??? Cable). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor.

Rear of the unit

2

Connecting

HDMI cable

TV

Set the TV???s source to HDMI (refer to TV???s Owner???s manual).

,,Note

Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections.

2

Connecting

Additional information for HDMI

yy When you connect a HDMI or DVI compatible device make sure of the following:

-- Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.

-- The connected device???s video input is set correctly for this unit.

-- The connected device is compatible with 720x576p, 1280x720p, 1920x1080i or 1920x1080p video input.

yy Not all HDCP-compatible HDMI or DVI devices will work with this player.

-- The picture will not be displayed properly with non-HDCP device.

,,Note

yy If a connected HDMI device does not accept the audio output of the player, the HDMI device???s audio sound may be distorted or may not output.

yy When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to ???Resolution Setting??? on page 17)

yy Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 26).

yy Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again.

yy When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable.

yy If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m).

What is SIMPLINK?

Some functions of this unit are controlled by the TV???s remote control when this unit and LG TV???s with SIMPLINK are connected through HDMI connection.

Controllable functions by LG TV???s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

Refer to the TV owner???s manual for the details of SIMPLINK function.

LG TV???s with SIMPLINK function has the logo as shown above.

,,Note

Depending on the disc type or playing status, some SIMPLINK operation may differ from your purpose or not work.

Resolution setting

The player provides several output resolutions for HDMI OUT jack. You can change the resolution using [Setup] menu.

1.Press HOME (n).

2.Use a/dto select the [Setup] and press ENTER (b). The [Setup] menu appears.

3.Use w/sto select [DISPLAY] option then press dto move to the second level.

4.Use w/sto select the [Resolution] option then press ENTER (b) to move to the third level.

5.Use w/sto select the desired resolution then press ENTER (b) to confirm your selection.

,,Note

yy If your TV does not accept the resolution you have set on the player, you can set resolution to 576p as follows:

1.Press Bto open the disc tray.

2.Press Z(STOP) for more than 5 seconds.

yy When you set the resolution to 576i with HDMI connection, actual resolution is outputted to 576p.

yy If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto].

yy If you select a resolution that your TV does not accept, the warning message will appear. After resolution change,

if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution.

yy The 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and

based on the native video frame rate of the content on the BD-ROM disc.

2

Connecting

2

Connecting

Connecting to an amplifier

Make one of the following connections, depending on the capabilities of your existing equipment.

yy HDMI audio connection

yy Digital audio connection (page 19)

Since many factors affect the type of audio output, see ???Audio output specifications??? for details (pages 53).

About digital multi-channel sound

A digital multi-channel connection provides the best sound quality. For this, you need a multi- channel Audio/Video Receiver that supports one or more of the audio formats supported by your player. Check the logos on the front of the Audio/ Video receiver and the manual. (PCM Stereo, PCM Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and/or DTS-HD)

Connecting to an amplifier via HDMI output

Connect the player???s HDMI OUT jack to the corresponding in jack on your amplifier using a HDMI cable.

Rear of the unit

HDMI cable

Receiver/Amplifier

HDMI cable

Connecting to an amplifier via digital audio output

Connect the player???s COAXIAL OUT jack to the corresponding in jack on your amplifier using an optional digital audio cable.

Rear of the unit

Coaxial cable

Receiver/Amplifier

You will need to activate the player???s digital output. (See ???[AUDIO] Menu??? on pages 27.)

Connecting 19

2

Connecting

2

Connecting

Connecting to your home network

This player can be connected to a local area network (LAN) via the LAN port on the rear panel. By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and on-line content services.

Wired network connection

Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference.

Please refer to the documentation for your network device for further instructions.

Connect the player???s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable.

,,Note

yy When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock.

yy Do not connect a modular phone cable to the LAN port.

yy Since there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider.

Broadband service

Router

Rear of the unit

Wired network setup

If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player???s network setting to be adjusted. Adjust the [NETWORK] setting as follow.

Preparation

Before setting the wired network, you need to connect the broadband internet to your home network.

Connecting 21

2.Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.

2

Connecting

Network will automatically be connected to the unit.

,,Note

If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using w/s/a/dand numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.

2.Select [Next] and press ENTER (b) to apply network settings.

Network connection status is displayed on the screen.

3.Press ENTER (b) while [Close] is highlighted to finish the wired network settings.

2

Connecting

22 Connecting

USB device connection

This player can play movie, music and photo files contained in the USB device.

Playback content in the USB device

1.Insert a USB device to the USB port until it fits into place.

When you connect the USB device on the HOME menu, the player plays a music file contained in the USB storage device automatically. If the USB storage device is containing various types of files, a menu for the file type selection will appear.

File loading may takes few minutes depending on the number of content stored in the USB storage device. Press ENTER (b) while [Cancel] is selected to stop loading.

2.Press HOME (n).

3.Select [Movie], [Photo] or [Music] using a/d, and press ENTER (b).

4.Select the [USB] option using w/s, and press ENTER (b).

5.Select a file using w/s/a/d, and press PLAY or ENTER (b) to play the file.

6.Withdraw the USB device carefully.

,,Note

yy This player supports USB flash drive/ external HDD formatted in FAT32 and NTFS when accessing files (music, photo, movie). However, for Blu-ray contents, only FAT32 format is supported. Use the USB flash drive/ external HDD formatted in either FAT32 or NTFS when enjoying Blu-ray contents.

yy The USB device can be used for the local storage for enjoying BD-Live discs with Internet.

yy This unit can support up to 4 partitions of the USB device.

yy Do not extract the USB device during operation (play, etc.).

yy A USB device which requires additional program installation when you have connected it to a computer, is not supported.

yy USB device: USB device that supports USB1.1 and USB2.0.

yy Movie, music and photo files can be played. For details of operations on each file, refer to relevant pages.

yy Regular back up is recommended to prevent data loss.

yy If you use a USB extension cable, USB HUB or USB Multi-reader, the USB device may not be recognized.

yy Some USB device may not work with this unit.

yy Digital camera and mobile phone are not supported.

yy USB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device.

2

Connecting

3

When you turn on the unit for the first time, the initial setup wizard appears on the screen. Set the display language and network settings on the initial setup wizard.

1.Press 1(POWER).

The initial setup wizard appears on the screen.

2.Use w/s/a/dto select a display language and press ENTER (b).

Press ENTER (b) while [Finish] is highlighted to finish the initial setup settings. If there is any settings to be changed, use a/dto select [Previous] and press ENTER (b).

Setting System

3.Read and prepare the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.

If wired network is connected, the network connection setting will automatically be finished.

Adjust the setup settings

You can change the settings of the player in the [Setup] menu.

1.Press HOME (n).

2.Use a/dto select the [Setup] and press ENTER (b). The [Setup] menu appears.

3.Use w/sto select the first setup option, and press dto move to the second level.

4.Use w/sto select a second setup option, and press ENTER (b) to move to the third level.

[DISPLAY] Menu

TV Aspect Ratio

Select a TV aspect ratio option according to your TV type.

[4:3 Letter Box]

Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture.

[4:3 Pan Scan]

Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both sides of the picture are cut off.

[16:9 Original]

Select when a 16:9 wide TV is connected. The 4:3 picture is displayed with an original 4:3 aspect ratio, with black bars appearing at the left and right sides.

[16:9 Full]

Select when a 16:9 wide TV is connected. The 4:3 picture is adjusted horizontally (in a linear proportion) to fill the entire screen.

,,Note

You cannot select [4:3 Letter Box] and

[4:3 Pan Scan] option when the resolution is set to higher than 720p.

3

Setting System

Resolution

Sets the output resolution of the HDMI video signal.

Refer to page 17 for details about the resolution setting.

[Auto]

If the HDMI OUT jack is connected to TVs providing display information (EDID),

automatically selects the resolution best suited to the connected TV.

[1080p]

Outputs 1080 lines of progressive video.

HDMI Color Setting

Select the type of output from the HDMI OUT jack.

For this setting, please refer to the manuals of your display device.

[YCbCr]

Select when connecting to a HDMI display device.

[RGB]

Select when connecting to a DVI display device.

3

Setting System

[1080i]

Outputs 1080 lines of interlaced video.

[720p]

Outputs 720 lines of progressive video.

[576p]

Outputs 576 lines of progressive video.

[576i]

Outputs 576 lines of interlaced video.

3D Mode

Select the type of output mode for Blu-ray 3D disc playback.

[Off]

Blu-ray 3D disc playback will output as 2D mode like a normal BD-ROM disc playback.

[On]

Blu-ray 3D disc playback will output as 3D mode.

1080p Display Mode

When the resolution is set to 1080p, select

[24 Hz] for smooth presentation of film material (1080p/24 Hz) with a HDMI-equipped display compatible with 1080p/24 Hz input.

,,Note

yy When you select [24 Hz], you may experience some picture disturbance when the video switches video and film material. In this case, select [50 Hz].

yy Even when [1080p Display Mode] is set to [24 Hz], if your TV is not compatible with 1080p/24 Hz, the actual frame frequency of the video output will be 50 Hz to match the video source format.

Home Menu Guide

This function allows you to display or delete the guide bubble on the Home Menu. Set this option to [On] for displaying guide.

[LANGUAGE] Menu

Display Menu

Select a language for the [Setup] menu and on- screen display.

Disc Menu/Disc Audio/

Disc Subtitle

Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu.

[Original]

Refers to the original language in which the disc was recorded.

[Other]

Press ENTER (b) to select another language. Use number buttons then press ENTER (b) to enter the corresponding 4-digit number according to the language code list on page 50.

[Off] (Disc Subtitle only)

Turn off Subtitle.

,,Note

Depending on the disc, your language setting may not work.

[AUDIO] Menu

Each disc has a variety of audio output options. Set the player???s Audio options according to the type of audio system you use.

,,Note

Since many factors affect the type of audio output, see ???Audio output specifications??? on page 53 for details.

Digital Output

[PCM Stereo] (HDMI, COAXIAL)

Select if you connect this unit???s HDMI OUT or COAXIAL OUT jack to a device with two- channel digital stereo decoder.

[PCM Multi-Ch] (HDMI only)

Select if you connect this unit???s HDMI OUT jack to a device with multi-channel digital decoder.

[DTS Re-Encode] (HDMI, COAXIAL)

Select if you connect this unit???s HDMI OUT or COAXIAL OUT jack to a device with DTS decoder.

[BitStream] (HDMI, COAXIAL)

Select if you connect this unit???s DIGITAL AUDIO OUT and HDMI OUT jack to a device with LPCM, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and DTS-HD decoder.

3

Setting System

3

Setting System

Sampling Freq.

(Digital Audio Output)

[48 kHz]

Select this if your A/V Receiver or Amplifier is not capable of handling 192 kHz and 96 kHz signal. When this choice is made, this unit automatically converts any 192 kHz and 96 kHz signals to 48 kHz so your system can decode them.

[96 kHz]

Select this if your A/V Receiver or Amplifier is not capable of handling 192 kHz signals. When this choice is made, this unit automatically converts any 192 kHz signals to 96 kHz so your system can decode them.

[192 kHz]

Select this if your A/V Receiver or Amplifier is capable of handling 192 kHz signals.

Check the documentation for your A/V Receiver or Amplifier to verify its capabilities.

DRC (Dynamic Range Control)

This function allows you to listen to a movie at a lower volume without losing clarity of sound.

[Auto]

The dynamic range of the Dolby TrueHD audio output is specified by itself.

And the dynamic range of the Dolby Digital and Dolby Digital Plus are operated as same as the [On] mode.

[On]

Compress the dynamic range of the Dolby Digital, Dolby Digital Plus or Dolby TrueHD audio output.

[Off]

Turns off this function.

,,Note

The DRC setting can be changed only when a disc is not inserted or the unit is in complete stop mode.

[LOCK] Menu

The [LOCK] settings affect only BD-ROM and DVD playback.

To access the any features in [LOCK] settings, you must enter the 4-digit security code you have created.

If you have not entered a password yet, you are prompted to do so. Enter a 4-digit password twice, and press ENTER (b) to create a new password.

Password

You can create or change the password.

[None]

Enter a 4-digit password twice, and press ENTER (b) to create a new password.

[Change]

Enter the current password and press ENTER (b). Enter a 4-digit password twice, and press ENTER (b) to create a new password.

If you forget your password

If you forget your password, you can clear it using the following steps:

1.Remove any disc that might be in the player.

2.Select [Password] option in the [Setup] menu.

3.Use Number buttons to enter ???210499???. The password is cleared.

,,Note

If you make a mistake before pressing ENTER (b), press CLEAR. Then input the correct password.

DVD Rating

Blocks playback of rated DVD based on their content. (Not all discs are rated.)

[Unlock]

If you select [Unlock], parental control is not active and the disc plays in full.

[Rating 1-8]

Rating one (1) has the most restrictions and rating eight (8) is the least restrictive.

Blu-ray Disc Rating

Set an age limit of BD-ROM play. Use number buttons to input an age limit for BD-ROM viewing.

[255]

All BD-ROM can be played.

[0-254]

Prohibits play of BD-ROM with corresponding ratings recorded on them.

,,Note

The [Blu-ray Disc Rating] will be applied only for the Blu-ray disc that containing the Advanced Rating Control.

Area Code

Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 49.

3

Setting System

3

Setting System

[NETWORK] Menu

The [NETWORK] settings are needed to use the software update, BD-Live and on-line content services.

Connection Setting

If your home network environment is ready to connect the player, the player needs to be set the wired network connection for network

communication. (See ???Connecting to your Home Network??? on pages 20.)

Connection Status

If you want to check tshe network status on this player, select the [Connection Status] options and press ENTER (b) to check whether a connection to the network and the internet have been established.

BD-LIVE connection

You can restrict Internet access when BD-Live functions are used.

[Permitted]

Internet access is permitted for all BD-Live contents.

[Partially permitted]

Internet access is permitted only for BD- Live contents which have content owner certificates. Internet access and AACS Online

functions are prohibited for all BD-Live contents without a certificate.

[Prohibited]

Internet access is prohibited for all BD-Live contents.

[OTHERS] Menu

DivX?? VOD

ABOUT DIVX VIDEO: DivX?? is a digital video format created by DivX, LLC, a subsidiary of Rovi

Corporation. This is an official DivX Certified?? device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified?? device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration.

[Register]

Displays the registration code of your player.

[Deregister]

Deactivate your player and display the deactivation code.

,,Note

All the downloaded videos from DivX(R) VOD with this player???s registration code can only be played on this unit.

Auto Power Off

The screen saver appears when you leave the player in Stop mode for about five minutes. If you set this option to [On], the unit automatically turns off within 20 minutes since the Screen Saver is displayed. Set this option to [Off ] to leave the screen saver until the unit is operated by the user.

Initialize

[Factory Set]

You can reset the player to its original factory settings.

[Blu-ray Storage Clear]

Initializes the BD-Live contents from the connected USB storage.

,,Note

If you reset the player to its original factory settings using [Factory Set] option, you have to set all the activation for the on-line services and network settings again.

Software

[Information]

Displays the current software version.

[Update]

You can update the software by connecting the unit directly to the software update server (see page 47).

Disclaimer Notice

Press ENTER (b) to view the notice of Network Service Disclaimer.

System Setting 31

3

Setting System

4

Operating

General Playback

Using [HOME] menu

The home menu appears when you press HOME (n). Use a/dto select a category and press ENTER (b).

A[Movie] - Plays video contents.

B[Photo] - Plays photo contents.

C[Music] - Plays audio contents. [Premium] - Displays the Premium Home

Dscreen.

E[Setup] - Adjusts the system settings.

Playing a disc

erto

1.Press B(OPEN/CLOSE), and place a disc on the disc tray.

2.Press B(OPEN/CLOSE) to close the disc tray.

For the most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically.

3.Press HOME (n).

4.Select [Movie] or [Music] using a/d, and press ENTER (b).

5.Select [Blu-ray Disc], [DVD], [VR] or [Audio] option using w/s, and press ENTER (b).

,,Note

yy Playback functions described in this manual are not always available in every files and media. Some functions can be restricted depending on many factors.

yy Depending on the BD-ROM titles, a USB device connection may be needed for the proper playback.

yy Unfinalized DVD-VR format discs may not be played in this player.

yy Some DVD-VR discs are made with CPRM data by DVD RECORDER. This unit cannot support these kinds of discs.

Playing Blu-ray 3D disc

e

This player can play the Blu-ray 3D discs which contains separate views for the left and right eyes.

Preparation

In order to playback Blu-ray 3D title in stereoscopic 3D mode, you need to:

yYCheck your TV is 3D capable and has HDMI input(s).

yy Wear 3D glasses to enjoy the 3D experience if it is necessary.

yYCheck whether the BD-ROM title is the Blu- ray 3D disc or not.

yYConnect an HDMI cable (Type A, High Speed HDMI??? Cable) between the player???s HDMI output and TV???s HDMI input.

1.Press HOME (n), and set the [3D Mode] option on the [Setup] menu to [On] (page 26).

2.Press B(OPEN/CLOSE), and place a disc on the disc tray.

3.Press B(OPEN/CLOSE) to close the disc tray. The playback starts automatically.

4.Refer to the owner???s manual of your 3D-ready TV for the further instruction.

You may need to adjust the display settings and focus on your TV???s setting for the improved 3D effect.

>>Caution

yy Watching a 3D content for a long period time may cause dizziness or tiredness.

yy It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman.

yy If you are experiencing headache, tiredness or dizziness while viewing contents in 3D, it is strongly recommended to stop the playback and rest until you feel normal.

Enjoying BD-Live???

e

BD-ROM supporting BD-Live that has a network extension function allows you to enjoy more functions such as downloading new movie trailers by connecting this unit to the internet.

1.Check the network connection and settings (page 20).

2.Insert a USB storage device to the USB port on the front panel.

A USB storage device is needed to download bonus content.

3.Press HOME (n), and set the [BD-LIVE connection] option on the [Setup] menu (page 30).

Depending on a disc, the BD-Live function may not be operated if [BD-LIVE connection] option is set to [Partially Permitted].

4.Insert a BD-ROM with BD-Live.

The operations are differ depending on the disc. Refer to the manual supplied with the disc.

>>Caution

Do not extract the connected USB device while content is being downloaded or a Blu- ray disc is still in the disc tray. Doing so may damage the connected USB device and BD- Live features may not operate properly with the damaged USB device anymore. If the connected USB device seems damaged from such an action, you can format the connected USB device from the PC and reuse it with this player.

,,Note

yy Some BD-Live contents may be restrictively accessed in some territories by contents provider???s own decision.

yy It may take up to several minutes to load and start enjoying BD-Live contents.

4

Operating

4

Operating

To pause playback

Press M(PAUSE) while playback.

Press z(PLAY) to resume playback.

To play frame-by-frame (Video)

Press M(PAUSE) while movie playback.

Press M(PAUSE) repeatedly to play Frame-by-Frame playback.

To scan forward or backward

Press cor vto play fast forward or fast reverse during playback.

You can change the various playback speeds by pressing cor vrepeatedly.

To slow down the playing speed

While the playback is paused, press vrepeatedly to play various speeds of slow motion.

To skip to the next/previous chapter/track/file

During playback, press Cor Vto go to the next chapter/track/file or to return to the beginning of the current chapter/track/file.

Press Ctwice briefly to step back to the previous chapter/track/file.

To stop a slide show

Press Z(STOP) while slide show.

To pause a slide show

Press M(PAUSE) while slide show.

Press z(PLAY) to re-start the slide show.

To skip to the next/previous photo

While viewing a photo in full screen, press aor d to go to the previous or next photo.

Using the disc menu

ero

To display the disc menu

The menu screen may be displayed first after loading a disc which contains a menu. If you want to display the disc menu while playback, press DISC MENU.

Use w/s/a/dbuttons to navigate through menu items.

To display the Pop-up menu

Some BD-ROM discs contain Pop-up menu that appears while playback.

Press TITLE/POP-UP while playback, and use w/s/a/dbuttons to navigate through menu items.

Resume playback

eroyt u

The unit records the point where you pressed the Z(STOP) depending on the disc.

If ???MZ(Resume Stop)??? appears on the screen briefly, press z(PLAY) to resume playback (from the scene point). If you press Z(STOP) twice or unload the disc, ???Z(Complete Stop)??? appears on the screen. The unit will clear the stopped point.

,,Note

yy The resume point may be cleared when a button is pressed (for example; 1(POWER), B(OPEN/CLOSE), etc).

yy On BD-ROM discs with BD-J, the resume playback function does not work.

yy If you press Z(STOP) once during BD-ROM interactive title playback, the unit will be in Complete Stop mode.

Last scene memory

er

This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled.

,,Note

yy Last Scene Memory function for a previous disc is erased once a different disc is played.

yy This function may not work depending on the disc.

yy On BD-ROM discs with BD-J, the last scene memory function does not work.

yy This unit does not memorize settings of a disc if you switch off the unit before commencing to play it.

Advanced Playback

Repeat playback

erotu y

During playback, press REPEAT (h) repeatedly to select a desired repeat mode.

Blu-ray Disc / DVD / Movie files

jA- ??? Selected portion will be repeated continually. (page 36)

jChapter ??? The current chapter will be played back repeatedly.

jTitle ??? The current title will be played back repeatedly.

jAll ??? All the tracks or files will be played back repeatedly.

To return to normal playback, press REPEAT (h) repeatedly to select [Off ].

Audio CDs/Music files

;Track ??? The current track or file will be played back repeatedly.

:All ??? All the tracks or files will be played back repeatedly.

l??? The tracks or files will be played back in random order.

l:All ??? All the tracks or files will be played back repeatedly in random order.

kA-B ??? Selected portion will be repeated continually. (Audio CD only)

To return to normal playback, press CLEAR.

,,Note

yy If you press Vonce during Repeat Chapter/Track playback, the repeat playback cancels.

yy This function may not work on some disc or title.

4

Operating

4

Operating

Repeating a specific portion

eroty

This player can repeat a portion you have selected.

1.While playback, press REPEAT (h) to select [A-] at the beginning of the portion you wish to repeat.

2.Press ENTER (b) at the end of the portion. Your selected portion will be repeated continually.

3.To return to normal playback, press REPEAT (h) repeatedly to select [Off ].

,,Note

yy You cannot select a portion less than 3 seconds.

yy This function may not work on some disc or title.

Viewing content information

y

The player can display the content information.

1.Select a file using w/s/a/d.

2.Press INFO/MENU (m) to display the option menu.

3.Select the [Information] option using w/s, and press ENTER (b).

The file information appears on the screen.

While movie playback, you can display the file information by pressing TITLE/POP-UP.

,,Note

The information displayed on the screen may not correct comparing actual content information.

Changing content list view

yui

On the [Movie], [Music] or [Photo] menu, you can change the content list view.

Method 1

Press red (R) coloured button repeatedly.

Method 2

1.On the content list, press INFO/MENU (m) to display the option menu.

2.Use w/sto select the [View Change] option.

3.Press ENTER (b) to change the content list view.

Selecting a subtitle file

y

If the subtitle file name is different from the movie file name, you need to select the subtitle file on the [Movie] menu before playing the movie.

1.Use w/s/a/dto select the subtitle file you wish to play in the [Movie] menu.

2.Press ENTER (b).

Press ENTER (b) again to deselect the subtitle file. Selected subtitle file will be displayed when you play the movie file.

,,Note

If you press Z(STOP) while playback, the subtitle selection is cancelled.

Options while viewing a photo

i

You can use various options during viewing a photo in full screen.

1.While viewing a photo in full screen, press INFO/ MENU (m) to display the option menu.

2.Select an option using w/s.

ACurrent photo/Total number of photos

??? Use a/dto view previous/next photo.

BSlide Show ??? Press ENTER (b) to start or pause slide show.

CMusic Select ??? Select the background music for the slide show (page 38).

DMusic ???Press ENTER (b) to start or pause background music.

ERotate ??? Press ENTER (b) to rotate the photo clockwise.

FZoom ??? Press ENTER (b) to display the [Zoom] menu.

GEffect ??? Use a/dto select a transition effect between photos in a slide show.

HSpeed ??? Use a/dto select a delaying speed between photos in a slide show.

3.Press BACK (1) to exit the option menu.

4

Operating

4

Operating

Listening to music while slide show

i

You can display photo files while listening to music files.

1.While viewing a photo in full screen, press INFO/ MENU (m) to display the option menu.

2.Use w/sto select [Music Select] option, and press ENTER (b) to display the [Music Select] menu.

3.Use w/sto select a device, and press ENTER (b).

4.Use w/sto select a file or a folder you wish to play.

Select gand press ENTER (b) to display the upper directory.

5.Use dto select [OK], and press ENTER (b) to complete music selection.

On-screen display

You can display and adjust various information and settings about the content.

Displaying content information on-screen

eroy

1.While playback, press INFO/MENU (m) to show various playback information.

ATitle ??? current title number/total number of titles

BChapter ??? current chapter number/total number of chapters

CTime ??? elapsed playing time/total playback time

DAudio ??? selected audio language or channel

ESubtitle ??? selected subtitle.

FAngle ??? selected angle/total number of angles

GTV Aspect Ratio ??? selected TV aspect Ratio

HPicture Mode ??? selected picture mode

4

Operating

4

Operating

Hearing a different audio

eroy

1.During playback, press INFO/MENU (m) to display the on-screen display.

2.Use w/sto select the [Audio] option.

3.Use a/dto select desired audio language, audio track or audio channel.

,,Note

yy Some discs allow you to change audio selections only via the disc menu. In this case, press TITLE/POP-UP or DISC MENU button and choose the appropriate audio from the selections on the disc menu.

yy Immediately after you have switched sound, there may be a temporary discrepancy between the display and actual sound.

yy On BD-ROM disc, the multi audio format (5.1CH or 7.1CH) is displayed with [MultiCH] in the on-screen display.

yy You can select the [Audio] option on the on- screen display directely by pressing AUDIO ([) button.

Changing the TV Aspect Ratio

eoy

You can change the TV aspect ratio setting while playback.

1.During playback, press INFO/MENU (m) to display the On-Screen display.

2.Use w/sto select the [TV Aspect Ratio] option.

3.Use a/dto select desired option.

4.Press BACK (1) to exit the On-Screen display.

,,Note

Even if you change the value of the [TV Aspect Ratio] option in on-screen display, the [TV Aspect Ratio] option in the [Setup] menu is not changed.

Changing subtitle Code Page

y

If the subtitle is displayed in broken letter, you can change the subtitle code page to view the subtitle file properly.

1.During playback, press INFO/MENU (m) to display the playback menu.

2.Use w/sto select the [Code Page] option.

3.Use a/dto select desired code option.

Changing the Picture Mode

eroy

You can change the [Picture mode] option while playback.

1.During playback, press INFO/MENU (m) to display the On-Screen display.

2.Use w/sto select the [Picture Mode] option.

3.Use a/dto select desired option.

4.Press BACK (1) to exit the On-Screen display.

Setting the [User setting] option

1. During playback, press INFO/MENU (m) to display the on-screen display.

2. Use w/sto select the [Picture Mode] option.

3. Use a/dto select the [User setting] option, and press ENTER (b).

4. Press BACK (1) to exit the on-screen display.

4. Use w/s/a/dto adjust the [Picture Mode] options.

Select [Default] option then press ENTER (b) to reset the all video adjustments.

5. Use w/s/a/dto select the [Close] option, and press ENTER (b) to finish setting.

4

Operating

4

Operating

42 Operating

Using the Premium

You can use various content services via Internet with the Premium feature.

1.Check the network connection and settings (page 20).

2.Press HOME (n).

3.Select the [Premium] using a/d, and press ENTER (b).

4.Select an on-line service using w/s/a/d, and press ENTER (b).

,,Note

yy Detailed information of each service, contact to the content provider or visit suppot link of the service.

yy The content of Premium services and service related information, including user interface, is subject to changes. Please refer to the web site of each service for most up- to-date information.

yy When you are first time to access [Premium] feature, current country setting appears. If you want to change the country setting, select [Edit] and press ENTER (b).

Troubleshooting 43

Troubleshooting

General

5

Troubleshooting

Customer support

You can update the Player using the latest software to enhance the products operation and/or add new features. To obtain the latest software for this player (if updates have been made), please visit http://www.lg.com/global/support or contact LG Electronics customer care centre.

Open source software notice

To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are available to download with the source code.

5

Troubleshooting

6

Appendix

Controlling a TV with the supplied remote control

You can control your TV using the buttons below.

Depending on the unit being connected, you may not be able to control your TV using some of the buttons.

Setting up the remote to control your TV

You can operate your TV with the supplied remote control.

If your TV is listed in the table below, set the appropriate manufacturer code.

1.While holding down 1(TV POWER) button, and press the manufacturer code for your TV with the numerical buttons (see the table below).

2.Release the 1(TV POWER) button to complete setting.

Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again.

Network software update

Network update notification

From time to time, performance improvements and/or additional features or services may be made available to units that are connected to a broadband home network. If there is new software available and the unit is connected to a broadband home network, the player will inform you about the update as follows.

Option 1

1.The update menu will appear on the screen when you turn off the player.

2.Use a/dto select a desired option and then press ENTER (b).

Option 2

If the software update is available from the update server, the ???Update??? icon appears in the Home menu. Press blue (B) coloured button to start the update procedure.

Software update

You can update the player using the latest software to enhance the products operation and/or add new features. You can update the software by connecting the unit directly to the software update server.

,,Note

yy Before updating the software in your player, remove any disc and USB Device from the player.

yy Before updating the software in your player, turn the player off and then turn it back on.

yy During the software update procedure, do not turn off the player or disconnect AC power, or do not press any button.

yy If you cancel the update, turn off the power and turn it on for stable performance.

yy This unit cannot be updated to previous software version.

1.Check the network connection and settings (page 20).

2.Select [Software] option in the [Setup] menu then press ENTER (b).

3.Select [Update] option, and press ENTER (b).

The player will check for the newest update.

,,Note

yy Pressing ENTER (b) while checking for the update will end the process.

yy If there is no update available, the Message, ???No update is found.??? appears. Press ENTER (b) to return to the [Home Menu].

6

Appendix

6

Appendix

48 Appendix

4.If newer version exists, the message ???Do you want to download it???? appears.

5.Select [OK] to start update. (Selecting [Cancel] will end the update.)

6.The player starts downloading the newest update from the server. (Downloading will takes several minutes depending on your home network condition)

7.When downloading is completed, the message, ???Download is complete. Do you want to update???? appears.

8.Select [OK] to start updating. (Selecting [Cancel] will end the update and downloaded file will not be re-usable. To update software the next time, the software update procedure has to be started from the beginning again.)

>>Caution

Do not turn off the power during the software update.

,,Note

If the software includes the driver update, disc tray may open during the process.

9.When update is completed, the power will be turned automatically in a few seconds.

10.Turn the power back on. The system now operates with the new version.

,,Note

The Software Update function may not work properly depending on your internet environment. In this case, you can obtain the latest software from the authorized LG Electronics Service Centre then update your player. Refer to ???Customer support??? on page 45.

6

Appendix

50 Appendix

Language code list

Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu].

Blu-ray Disc???, Blu-ray???, Blu-ray 3D???, BD-Live???, BONUSVIEW??? and the logos are trademarks of the Blu-ray Disc Association.

???DVD Logo??? is a trademark of DVD Format/Logo Licensing Corporation.

Java is a trademark of Oracle and/or its affiliates.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

???x.v.Colour??? is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. ?? DTS, Inc. All Rights Reserved.

???AVCHD??? and the ???AVCHD??? logo are trademarks of Panasonic Corporation and Sony Corporation.

DivX??, DivX Certified?? and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.

6

Appendix

*1 The secondary and interactive audio may not be included in the output bitstream if [Digital Output] option is set to [BitStream]. (Except LPCM Codec : the output always include interactive and secondary audio.)

*2 This player automatically selects the HDMI audio according to the decoding capability of the connected HDMI device even though [Digital Output] option is set to [BitStream].

*3 On the PCM audio output, the sampling frequency of DIGITAL AUDIO OUT is limited to 96 kHz.

*4 If the [Digital Output] option is set to [DTS re- encode], the audio output is limited to 48 kHz and 5.1Ch. If the [Digital Output] option is set to [DTS re-encode], the DTS Re-encode audio is outputted for BD-ROM discs, and the original audio is outputted for the other discs (like [BitStream]).

yy If the HDMI OUT jack is connected to your TV with High Speed HDMI??? Cable and Dolby Digital Plus/Dolby TrueHD is outputted from HDMI OUT jack, COAXIAL OUT jack is limited to ???PCM 2ch??? (When the HDMI and DIGITAL AUDIO OUT are connected simultaneously).

Appendix

Maintenance

Handling the unit

When shipping the unit

Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Keeping the exterior surfaces clean

yy Do not use volatile liquids such as insecticide spray near the unit.

yy Wiping with strong pressure may damage the surface.

yy Do not leave rubber or plastic products in contact with the unit for a long period of time.

Notes on discs

Handling discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc.

Storing discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.

Cleaning discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the centre to out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

6

Appendix

Maintaining the unit

The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service centre.

Important information relating to network services

All information, data, documents, communications, downloads, files, text, images, photographs, graphics, videos, webcasts, publications, tools, resources, software, code, programs, applets, widgets, applications, products and other content (???Content???) and all services and offerings (???Services???) provided or made available by or through any third party (each a ???Service Provider???) is the sole responsibility of the Service Provider from whom it originated.

The availability of and access to Content and Services furnished by the Service Provider through the LGE Device are subject to change at any time, without prior notice, including, but not limited to the suspension, removal or cessation of all or any part of the Content or Services.

Should you have any inquiry or problem related to the Content or Services, you may refer to the Service Provider???s website for the most up-to- date information. LGE is neither responsible nor liable for customer service related to the Content and Services. Any question or request for service relating to the Content or Services should be made directly to the respective Content and Service Providers.

Please note that LGE is not responsible for any Content or Services provided by the Service Provider or any changes to, removal of, or cessation of such Content or Services and does not warrant or guaranty the availability of or access to such Content or Services.

Appendix 57

6

Appendix