Installation

Stand Installation

ENGLISH

Connection of TV

1.Connect the aerial cable to the socket marked ANTENNA IN on the back. For the best reception an outdoor aerial should be used.

2.To connect an additional equipment, see the Connection of external equipment section.

3.Connect the power cord.

Note: Here shown may be somewhat different from your set.

Installation

How to remove the Cable management

First, press the cable management.

Hold the Cable management with both hands and pull it upward.

Note: Do not hold the CABLE MANAGEMENT when moving the product. (If the product is dropped,you may be injured or the product may be broken.)

Wall Mount: Horizontal installation

ENGLISH

Place the ring spacers on the set before installing the wall mounting bracket so that the inclination of the backside of the set can be adjusted perpendicularly.

4 inches

10~12

Installation

Kensington Security System

-The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.

-For the detailed installation and use of the Kensington Security System, refer to the user???s guide provided with the Kensington Security System.

For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.

Note:

- The Kensington Security System is an optional accessory.

Note:

a.If the TV feels cold to the touch, there may be a small ???flicker??? when when it is turned on. This is normal, there is nothing wrong with TV.

b.Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

c.Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

d.Here shown may be somewhat different from your set.

7

ENGLISH

Location and function of controls

ENGLISH

All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the top panel of the set. Only the remote control handset supplied will operate this set.

Remote control handset

Before you use the remote control handset, please install the

batteries. See the next page.

1.POWER

switches the set on from standby or off to standby.

2.NUMBER BUTTONS

switches the set on from standby and selects a programme.

3.LIST

displays the programme table.

4.PSM (Picture Status Memory) recalls your preferred picture setting.

5.MUTE

switches the sound on or off.

Press the MUTE button. The sound is

switched off and the display appears. You can cancel it by pressing the MUTE, F / G, I/II, or SSM button.

6.D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.

F / G (Volume Down/Up)

adjusts the volume. adjusts menu settings.

OK

accepts your selection or displays the current mode.

7.MENU

selects a menu.

8.SLEEP

sets the sleep timer.

9.TV

returns to the TV mode.

switches the set on from standby.

10.INPUT

selects the remote operating mode. switches the set on from standby.

11.Q.VIEW

returns to the previously viewed programme. Press the Q.VIEW button to view the last pro- gramme you were watching.

12.SSM (Sound Status Memory) recalls your preferred sound setting.

13.TELETEXT BUTTONS

These buttons are used for teletext.

For further details, see the ???Teletext??? section.

14.I/II

selects the language during dual language broadcast.

15.ARC (20LS2R*/ 23LS2R*) select your desired picture format.

16.COLOURED BUTTONS : These buttons are used for teletext (only TELETEXT models) or programme edit.

* : No function

Battery installation

The remote control handset is powered by two AAA batteries. To load the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.

Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.

7

8

1.ON/OFF (r / I)

switches the set on from standby or off to standby.

2.INPUT

selects the remote operating mode. switches the set on from standby.

3.MENU

selects a menu.

4.OK

accepts your selection or displays the current mode.

5.F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.

Top panel

PR VOL OK MENU INPUT /I

6 5 4 3 2 1

6.E / D (Programme Down/Up)

selects a programme or a menu item. switches the set on from standby.

7. REMOTE CONTROL SENSOR

8. POWER/STANDBY INDICATOR

- 15LS1R*/ 20LS1R*/ 20LS2R*/ 23LS2R* illuminates red in standby mode.

illuminates green when the set is switched on.

- 15LC1R*/ 20LC1R*

illuminates orange in standby mode. illuminates blue when the set is switched on.

Location and function of controls

Rear

ENGLISH

11

20LS2R*/ 23LS2R*

AC INPUT

Location and function of controls

Rear

ENGLISH

13

POWER TV INPUT

POWER

TV INPUT I/II

MENU

PR

OK

VOLVOL

PR

1 2 3

4 5 6

7 8 9

SSM 0

Basic operation

On and off

1.Press the POWER, D / E, TV, INPUT or NUMBER buttons to switch it on fully.

2.Press the POWER button. The set reverts to standby mode.

3.Pull out mains plugs to switch the set off.

Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains plug is replaced in the mains power socket.

On-Screen Menu Language / Country Selection

Installation guide menu appears on TV screen when it is turned on for the first time.

1.Press the D / E / F / G button and then, OK button to select your desired language.

2. Press the D / E / F / G button and then, OK button to select your country.

* If you want to change Language/ Country selection

1.Press the MENU button and then D / E button to select the SPECIAL menu.

2.Press the G button and then D / E button to select Language.

The menus can be shown on the screen in the selected language.

Or, Press the G button and then D / E button to select Country.

3.Press the G button and then D / E / F / G button to select your desired language or country.

4.Press the OK button.

5.Repeatedly press the MENU button to return to normal TV viewing.

Note:

a.If you don???t finish set up Installation Guide by pressing MENU button or time out of OSD (On Screen Display) display, it will continuously appear until completing set up whenever the set is turned on.

b.If you select wrong local country, the teletext may not appear correctly on the screen and some problem may happen during teletext operation.

c.Hebrew is added to Country of Installation Guide according to the countries which using Hebrew languages.

On screen menus

Menu selection

1.Press the MENU button and then D / E button to display each menu.

2.Press the G button and then D / E button to select a menu item.

3.Change the setting of an item in the sub or pull-down menu with F / G button.

You can move to the higher level menu by pressing the OK button and to move to the lower level menu by pressing the

MENU button.

Note :

a.The SCREEN (20LS1R*/20LC1R*) menu is not displayed.

b.In the teletext mode, menus are not displayed.

c.On some models, the Language will not be displayed.

Programme selection

You can select a programme number with the D / E or NUMBER buttons.

Volume adjustment

Press the F / G button to adjust the volume.

* : 20LS2R*, 23LS2R

ENGLISH

MENU

PR

OK

VOLVOL

PR

Station

Auto programme

Manual programme

Programme edit

Favourite programme

STATION menu

SCREEN menu

PICTURE menu

SPECIAL menu

SOUND menu

TIME menu

15

PSM SSM

MENU

PR

OK

VOLVOL

PR

1 2 3

4 5 6

7 8 9

0

Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the D / E or NUMBER buttons to scan the stations you have programmed.

Stations can be tuned using automatic or manual modes.

Auto programme tuning

All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.

1.Press the MENU button and then D / E button to select the

Station menu.

2.Press the G button and then D / E button to select Auto programme.

3.Press the G button. Select a TV system with the G button and then D / E button on the System menu;

BG : PAL B/G, SECAM B/G (Europe/East Europe)

I : PAL I/II (U.K./Ireland)

DK : PAL D/K, SECAM D/K (East Europe)

L : SECAM L/L??? (France)

4.Press the OK button.

5.Press the D / E button to select Storage from.

6.Select the beginning programme number with the F / G button or NUMBER buttons on the Storage from pull-down menu. Any number under 10 is entered with a numeric ???0??? in front of it, i.e. ???05??? for 5.

7.Press the OK button.

8.Press the D / E button to select Search.

MENU Stop

DE F G OK MENU

9.Press the G button to begin auto programming. All receivable stations are stored.

To stop auto programming, press the MENU button.

When auto programming is completed, the Programme edit menu appears on the screen. See the ???Programme edit??? section to edit the stored programme.

10.Repeatedly press the MENU button to return to normal TV viewing.

ENGLISH

5.Press the OK button.

6.Press the D / E button to select System.

7.Select a TV system with the G button and then F / G button on the System menu;

BG : PAL B/G, SECAM B/G (Europe/East Europe)

I : PAL I/II (U.K./Ireland)

DK : PAL D/K, SECAM D/K (East Europe)

L : SECAM L/L??? (France)

8.Press the OK button.

MENU

PR

OK

VOLVOL

PR

1 2 3

PSM SSM

MENU

PR

OK

VOLVOL

PR

Assigning a station name

1.Repeat the ???Manual programme tuning??? steps 1 to 2.

2.Press the G button and then D / E button to select Name.

3.Press the G button and then use the D / E. You can use a blank, +, -, the number 0 to 9 and the alphabet A to Z. It can be saved 5 digits for name.

With the F button you can select in the opposite direction.

4.Select the position by pressing the F / G button and then make your choice of the second character, and so on.

5.Press the OK button to store it.

6.Repeatedly press the MENU button to return to normal TV viewing.

Fine tuning

Normally fine tuning is only necessary if reception is poor.

1.Repeat the ???Manual programme tuning??? steps 1 to 2.

2.Press the G button and then D / E button to select Fine.

3.Press the G button

4.Press the F / G button to fine tune for the best picture and sound on the Fine pull-down menu.

5.Press the OK button.

6.Repeatedly press the MENU button to return to normal TV viewing.

The finely tuned programme will be indicated by orange num- ber during programme selection.

Setting up TV stations

ENGLISH

Programme edit

This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or insert a blank station data into the selected programme number.

1.Press the MENU button and then D / E button to select the

Station menu.

2.Press the G button and then D / E button to select Programme edit.

3.Press the G button to display the Programme edit menu.

Programme edit

Delete Copy

MoveSkip

DE F G OK MENU

Deleting a programme

1.Select a programme to be deleted with the D / E or F / G button.

2.Press the RED button twice.

The selected programme is deleted, all the following

programmes are shifted up one position.

Programme edit

Delete

MENU

Copying a programme

PSM SSM

PR

1 2 3

4 5 6

7 8 9

0

PSM SSM

PR

OK

VOL VOL

PR

20

Favourite programme

This function lets you select your favourite programmes directly.

1.Press the MENU button and then D / E button to select the

Station menu.

2.Press the G button and then D / E to select Favourite programme.

3.Press the G button and then F / G button to select On or Off.

4.Press the D / E button to select -- ----- .

5.Select a desired programme with the F / G button.

6.To store another programme, repeat steps 4 to 5. You can store up to 8 programmes.

7.Repeatedly press the MENU button to return to normal TV viewing.

Repeatedly press the YELLOW button to select stored favourite programmes while it is selected On. Repeatedly press the YEL- LOW button to select previous programmes while it is selected Off.

Calling the programme table

You can check the programmes stored in the memory by displaying the programme table.

Displaying programme table

Press the LIST button to display the Programme table menu.

The programme table appears on the screen. One programme table contains ten programmes as below.

Programme List

DE F G OK MENU

Note :

a.You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode.

b.Some programmes with the channel number shown in the programme table indicate there is no station name assigned.

Selecting a programme in the programme table

Select a programme with the D / E or F / G button. Then press the OK button.

The set switches to the chosen programme number.

Paging through a programme table

There are 10 programme table pages in which contain 100 programmes.

Pressing the D / E or F / G button repeatedly turns the pages.

Press the MENU button to return to normal TV viewing.

Picture adjustment

ENGLISH

PSM (Picture Status Memory)

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select PSM.

3.Press the G button and then D / E button to select a picture set- ting on the PSM menu.

4.Press the OK button.

5.Repeatedly press the MENU button to return to normal TV viewing.

You can also recall a desired picture (Dynamic, Standard, Mild, Game or User) with PSM button on the remote control. The picture Dynamic, Standard, Mild and Game are programmed for optimum picture reproduction at the factory and cannot be changed.

Picture adjustment

You can adjust picture contrast, brightness, colour intensity, sharpness, tint to the levels you prefer.

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select PSM.

3.Press the G button and then D / E button to select User.

4.Press the G button and then D / E button to select the desired picture item.

5.Press the G button and then F / G button to make appropriate adjustments.

User

E

DE F G OK MENU

6.Repeatedly press the MENU button to return to normal TV viewing.

PSM SSM

HOLD SIZE MIX TIME

REVEAL INDEX MODE UPDATE

PR

OK

VOLVOL

PR

PSM

MENU

PR

OK

VOLVOL

PR

CSM (Colour Status Memory)

Selecting a factory setting colour set.

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select CSM.

3.Press the G button and then D / E button to select a color set- ting on the CSM menu: Cool, Normal, Warm or User (Red, Green, Blue).

4.Press the OK button.

5.Repeatedly press the MENU button to return to normal TV viewing.

Picture adjustment

ENGLISH

XD function

XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm.

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select XD.

3.Press the G button and then D / E button to select Auto or

Manual.

4.Press the OK button.

5.Repeatedly press the MENU button to return to normal TV viewing.

Selecting the Manual

This menu is activatived after selecting the User of PSM.

1.Press the G button and then D / E button to select XD Contrast, XD Colour or XD NR.

2.Press the G button and then D / E button to select On or Off.

3.Repeatedly press the MENU button to return to normal TV viewing.

XD Contrast : Optimizing the contrast automatically according to the brightness of the reflection.

XD Colour : Adjusting the colors of the reflection automatically to reproduce as closely as possible to the natural colors.

XD NR : Removing the noise up to the point where it does not dam- age the original picture.

DE F G OK MENU

Note: It???s not available to use this function in RGB[PC], HDMI[PC] mode. This feature is not available for all models.

PSM SSM

HOLD SIZE MIX TIME

REVEAL INDEX MODE UPDATE

MENU

PR

OK

VOLVOL

PR

PSM SSM

MENU

PR

OK

VOLVOL

PR

24

Cinema

Set up the TV for the best picture appearance for viewing movies.

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select Cinema.

3.Press the G button and then D / E button to select On or Off.

4.Repeatedly press the MENU button to return to normal TV viewing.

Note: This feature is not available for all models.

Reset

Returns to the default settings PSM, CSM, XD, Cinema at the factory.

1.Press the MENU button and then D / E button to select the

Picture menu.

2.Press the G button and then D / E button to select Reset.

3.Press the G button to initialize the adjusted value.

Note: This feature is not available for all models.

Sound adjustment

SSM (Sound Status Memory)

You can select your preferred sound setting; Flat, Music, Movie or Sports and you can also adjust the sound frequency of the equalizer.

1.Press the MENU button and then D / E button to select the

Sound menu.

2.Press the G button and then D / E button to select SSM.

3.Press the G button and then D / E button to select a sound setting on the SSM menu.

Sound Frequency Adjustment

a.Press the OK button in User.

b.Select a sound band by pressing the F / G button.

c.Make appropriate sound level with the D / E button.

d.Press the OK button to store it for the sound User.

User

0.1 0.5 1.2 5.0 10 kHz

DE F G OK MENU

4. Repeatedly press the MENU button to return to normal TV viewing.

You can also recall a desired sound setting (Flat, Music, Movie, Sports or User) with SSM button on the remote control. The sound settings Flat, Music, Movie and Sports are programmed for optimum sound reproduction at the factory and cannot be changed.

Note : If you press the SSM button after making appropriate adjustment on the User sub menu, the display User automatically appears even though you have already set a factory preset setting;

Flat, Music, Movie or Sports.

PSM SSM

HOLD SIZE MIX TIME

REVEAL INDEX MODE UPDATE

MENU

PR

OK

VOLVOL

PR

SSM

ENGLISH

I/II

26

Sound adjustment

Stereo/Dual reception

When a programme is selected, the sound information for the station appears after the programme number and station name disappear.

Mono sound selection

In stereo reception if the stereo signal is weak, you can switch to mono by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again.

Language selection for dual language broadcast

If a programme is received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly.

DUAL I sends the primary broadcast language to the loudspeakers. DUAL II sends the secondary broadcast language to the loudspeakers.

DUAL I+II sends a separate language to each loudspeaker.

NICAM reception

If your set is equipped with the receiver for NICAM reception, the high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received.

Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly.

1.When NICAM mono is received, you can select NICAM MONO or FM MONO.

2.When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If the stereo signal is weak, switch to FM mono.

3.When NICAM dual is received, you can select NICAM DUAL I,

NICAM DUAL II or NICAM DUAL I+II or MONO. When FM mono is selected the display MONO appears on the screen.

Sound output selection

In AV mode, you can select output sound for the left and right loud- speakers.

Repeatedly press the I/II button to select the sound output.

L+R : Audio signal from audio L input is sent to left loud-speaker and audio signal from audio R input is sent to right loud- speaker.

L+L : Audio signal from audio L input is sent to left and right loud- speakers.

R+R : Audio signal from audio R input is sent to left and right loud- speakers.

TIME Menu

Clock

You must set the time correctly before using on/off time function.

1.Press the MENU button and then D / E button to select the Time menu.

2.Press the G button and then D / E button to select Clock.

3.Press the G button and then D / E button to adjust the hour.

4.Press the G button and then D / E button to adjust the minute.

5.Press the MENU button to save.

On/Off time

The off timer automatically switches the set to standby at the preset time.

1.Press the MENU button and then D / E button to select the Time menu.

2.Press the G button and then D / E button to select Off time or

On time.

3.Press the G button and then D / E button to select On.

To cancel On/Off time function, press the D / E button to select Off.

4.Press the G button and then D / E button to adjust the hour.

5.Press the G button and then D / E button to adjust the minute.

6.Only On time function; Press the G button and then D / E button to adjust volume level and programe number.

7.Press the MENU button to save.

Note :

a.In the event of power interruption (disconnection or power failure), the clock must be reset.

b.Two hours after the set is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed.

c.Once the on or off time is set, these functions operate daily at the preset time.

d.Off Timer function overrides On Timer function if they are set to the same time.

e.The set must be in standby mode for the On Timer to work.

ENGLISH

PSM SSM

HOLD SIZE MIX TIME

REVEAL INDEX MODE UPDATE

MENU

PR

OK

VOLVOL

PR

27

PSM SSM

MENU

PR

OK

VOLVOL

PR

SLEEP

Auto sleep

If you select On on the Auto sleep menu, the set will automatical- ly switch itself to standby mode approximately ten minutes after a TV station stops broadcasting.

1.Press the MENU button and then D / E button to select the Time menu.

2.Press the G button and then D / E button to select Auto sleep.

3.Press the G button and then D / E button to select On or Off.

4. Press the MENU button to save.

Sleep timer

You don???t have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time has elapsed.

Press the SLEEP button to select the number of minutes.

The display ??? ---??? will appear on the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240. The timer begins to count down from the number of minutes selected.

Note :

a.To view the remaining sleep time, press the SLEEP button once.

b.To cancel the sleep time, repeatedly press the SLEEP button until the display ??? ---??? appears.

c.When you switch the set off, the set releases the preset sleep time.

Other functions

ENGLISH

Child lock

The TV can be set so that the remote control handset is needed to control it. This feature can be used to prevent unauthorized view- ing.

1.Press the MENU button and then D / E button to select the

Special menu.

2.Press the G button and then D / E button to select Child lock.

3.Press the G button and then D / E button to select On or Off on the Child lock menu.

4.Press the MENU button to save.

5.Repeatedly press the MENU button to return to normal TV viewing.

With the lock on, the display Child lock on appears on the screen if any button on the top panel is pressed while viewing the TV.

PSM SSM

MENU

PR

OK

VOLVOL

PSM SSM

HOLD SIZE MIX TIME

REVEAL INDEX MODE UPDATE

MENU

PR

OK

VOLVOL

PR

Other functions

XD Demo

Use it to see the difference between XD Demo on and XD Demo off.

1.Press the MENU button and then D / E button to select the

Special menu.

2.Press the G button and then D / E button to select XD Demo.

3.Press the G button to begin XD Demo.

DE F G OK MENU

4. Press the MENU button to return to normal TV viewing.

Note:

a.It???s not available to use this function in RGB[PC], HDMI[PC] mode.

b.This feature is not available for all models.

??? XD Demo

Menu Exit

Other functions

TV, AV and PC modes

Press the INPUT button and then D / E button to select desired mode.

Inputs can be set for TV, AV or PC mode. AV mode is used when a video cassette recorder (VCR), or other equipment is connected to the set.

Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the ???Connection of external equipment??? sec- tion.

ENGLISH

POWER TV INPUT

15LS1R*/15LC1R* 20LS1R*/20LC1R* 20LS2R*/ 23LS2R*

<15LS1R*/ 20LS1R*> <15LC1R*/ 20LC1R*>

:TV, AV1, AV2, RGB (RGB [DTV], RGB [PC]).

:TV, AV1, AV2.

:TV, AV1, AV2, Component, RGB (RGB [DTV], RGB [PC]), HDMI/DVI (HDMI/DVI [DTV], HDMI/DVI [PC]).

<20LS2R*/ 23LS2R*>

* : 15LS1R/15LC1R

The AV and PC modes are :

???AV 1 : VCR connected to the Euro scart socket of the set.

???AV 2 : VCR connected to the AV IN 2 or S-Video of the set.

???RGB-DTV : SET TOP connected to the PC INPUT and PC

SOUND socket.

??? RGB-PC : PERSONAL COMPUTER connected to the PC socket.

??? Component : DVD connected to the COMPONENT sockets on the back of set.

??? HDMI-DTV : DVD connected to the HDMI sockets on the back of set.

??? HDMI-PC : PERSONAL COMPUTER connected to the HDMI sockets on the back of set.

Auto AV switching

If your VCR outputs an AV switching voltage when connected to the Euro scart socket, the set will switch to AV1 mode automatically. But if you want to keep on watching TV mode, press the D / E or NUM- BER buttons.

INPUT

PR

OK

VOLVOL

PR

1 2 3

4 5 6

7 8 9

0

31

PR

OK

PR

1 2 3

4 5 6

7 8 9

0

TEXT

UPDATETIME

HOLDREVEAL

32

Teletext

- This feature is not available in all countries.

Teletext (or TOP text) is an optional function, therefore only a set with the teletext system can receive the teletext broadcast.

Teletext is a free service broadcast by most TV stations which gives up- to-the-minute information on news, weather, television programmes, share prices and many other topics.

The teletext decoder of this TV can support the SIMPLE, TOP and FAS- TEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.

Switch on/off

Press the TEXT button to switch to teletext. The initial page or last page appears on the screen.

Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT button to switch off teletext. The previous mode reappears.

SIMPLE text

Page selection

1.Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the cor- rect page number.

2.The D / E button can be used to select the preceding or following page.

Programming a colour button in LIST mode

If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the M button to switch to LIST mode.

Four teletext page numbers of your choice can be colour coded and easily selected by pressing the corresponding coloured button on the remote control handset.

1.Press a coloured button.

2.Using the NUMBER buttons, select the page you wish to pro- gramme.

3.Press the OK button. Then the selected page is stored as the selected page number by blinking once. From now on, you can select this page with the same coloured button.

4.The three other coloured buttons are programmed in this way.

Teletext

TOP text

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.

Block / group / page selection

1.With the blue button you can progress from block to block.

2.Use the yellow button to proceed to the next group with automatic overflow to the next block.

3.With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the D button can be used.

4.The red button permits to return to previous selection. Alternatively the E button can be used.

Direct page selection

Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit num- ber using the NUMBER buttons in TOP mode.

FASTEXT

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.

Page selection

1.Press the i button to select the index page.

2.You can select the pages which are colour coded along the bottom line with the same coloured but- tons.

3.Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode.

4.The D / E button can be used to select the preceding or following page.

Special teletext functions

? REVEAL

Press this button to display concealed information, such as solutions of riddles or puzzles. Press this button again to remove the information from the display.

SIZE

Selects double height text.

Press this button to enlarge the top half of the page.

Press this button again to enlarge the bottom half of the page.

Press this button again to return to the normal display.

UPDATE

Displays the TV picture on the screen while waiting for the new teletext page.

Press this button to view the updated teletext page.

HOLD

Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages.

The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inhibited.

To continue press this button again.

MIX

Displays the teletext pages superimposed on the TV picture.

To switch the TV picture off press this button again.

TIME

When viewing a TV programme, press this button to display the time at the top right hand cor- ner of the screen. Press this button again to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the top left hand cor- ner of the screen. To hold or change the sub page, press the NUMBER buttons.

Press again to exit this function.

33

ENGLISH

ANTENNA IN

VCR

1.Connect the RF out socket of the VCR to the aerial socket of the set.

2.Connect the aerial cable to the RF aerial in socket of the VCR.

3.Store the VCR channel on a desired programme number using the ???Manual programme tuning??? section.

4.Select the programme number where the VCR channel is stored.

5.Press the PLAY button on the VCR.

AV 1

VIDEO

S-VIDEO

AV IN 2

VCR

Audio/Video in sockets

1.Connect the audio/video out sockets of the VCR to audio/video in sockets of the set.

2.Press the INPUT button to select AV 2.

3.Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

Note : If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set.

Connection of external equipment

ENGLISH

S-Video/Audio in sockets (S-Video)

When connecting an S-VIDEO VCR to the S-VIDEO socket, the picture quality will be further improved.

1.Connect the S-Video socket of the VCR to the S-VIDEO socket of the set.

2.Connect the audio cable from the S-VIDEO VCR to the AUDIO sockets of the set.

3.Press the INPUT button to select AV 2.

4.Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

VIDEO

S-VIDEO

AV IN 2

S-VIDEO VCR

DVD input sockets

Euro scart socket

1.Connect the Euro scart socket of the DVD to the Euro scart socket of the set.

2.Press the INPUT button to select AV1.

3.Press the PLAY button on the DVD.

The DVD playback picture appears on the screen.

Component sockets (20LS2R*/ 23LS2R*)

1.Connect the video output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R- Y or Y PB PR) of the DVD to the COMPONENT sockets (Y PB PR) of the set.

2.Connect the audio cable from the DVD to COMPONENT/ AUDIO sockets of the set.

3.Press the INPUT button to select Component (480i/576i/480p/576p/720p/1080i).

4.Press the PLAY button on the DVD.

The DVD playback picture appears on the screen.

HDMI sockets (20LS2R*/ 23LS2R*)

1.Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the set.

2.Select HDMI/DVI (480p/576p/720p/1080i) input source with using the INPUT button on the remote control.

AV 1

VIDEO

S-VIDEO

AV IN 2

DVD

DVD

HDMI/DVI IN

DVD

RGB(PC/DTV) IN

AUDIO (RGB) IN

DTV Reciever

DTV Reciever

HDMI/DVI IN

DTV Reciever

H/P

DTV in sockets

RGB in socket (15LS1R*/15LC1R*/ 20LS2R*/ 23LS2R*)

1.Connect the SET TOP with the D-Sub output socket to RGB (PC/DTV) IN socket on the set and audio cable of the SET TOP

to the AUDIO (RGB) IN (15LS1R*/15LC1R*) or AUDIO (RGB/DVI) IN (20LS2R*/ 23LS2R*).

2.Press the INPUT button to select RGB (or RGB [DTV])

(576p/480p) - 15LS1R*/15LC1R*, (480p/576p/720p/1080i) - 20LS2R*/ 23LS2R*.

Component sockets (20LS2R*/ 23LS2R*)

1.Connect the SET TOP outputs to the COMPONENT (DVD/DTV) sockets (Y PB PR) on the set.

2.Connect the audio cable from the SET TOP to COMPONENT/ AUDIO sockets of the set.

3.Press the INPUT button to select Component (480i/576i/480p/576p/720p/1080i).

HDMI sockets (20LS2R*/ 23LS2R*)

1.Connect the HDMI output of the digital set-top box to the HDMI/DVI IN jack on the set.

2.Select HDMI/DVI (480p/576p/720p/1080i) input source with using the INPUT button on the remote control.

Headphone socket

Insert the headphone plug to the headphone socket of the set. You can listen to the sound through the headphone. To adjust the head- phone volume, press the F / G button. If you press the MUTE but- ton, the sound from the headphone is switched off.

Connection of PC

ENGLISH

PC in socket

RGB in socket (15LS1R*/15LC1R*/ 20LS2R*/ 23LS2R*)

1.Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set.

2.Connect the audio cable from the PC to the AUDIO (RGB) IN

(15LS1R*/15LC1R*) or AUDIO (RGB/DVI) IN (20LS2R*/ 23LS2R*) sockets of the set.

3.Press the INPUT button to select RGB (or RGB [PC]).

4.Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor.

RGB(PC/DTV) IN

AUDIO (RGB) IN

PERSONAL COMPUTER

HDMI sockets (20LS2R*/ 23LS2R*)

1.Connect the DVI output of the PC to the HDMI/DVI IN jack on the set.

2.Connect the audio cable from the PC to the AUDIO (RGB/DVI) IN (20LS2R*/ 23LS2R*) sockets of the set.

3.Select HDMI/DVI [PC] input source with using the INPUT button on the remote control.

Displayable Monitor Specification

HDMI/DVI IN

AUDIO (RGB) IN

PERSONAL COMPUTER

<15LS1R*/15LC1R*>

<20LS2R*, 23LS2R*>

PSM SSM

INPUT

MENU

PR

OK

VOLVOL

PR

PC Setup

You can adjust auto configure, manual configure and reset as you prefer.

1.Press the INPUT button and then D / E button to select the

RGB [PC].

2.Press the MENU button and then D / E button to select the

Screen menu.

3.Press the G button and then D / E button to select the desired screen function.

4. Make appropriate adjustments.

Auto configure

This function is for the automatic adjustment of the screen posi- tion, clock and phase. The displayed image will disappear for a few seconds while the Auto-configuration is in progress.

Manual configure

This function is for the manual adjustment of the screen posi- tion, clock and phase. Press the F / G button to make appro- priate adjustments.

??? H-Position / V-Position

This function is to adjust picture to left/right and up/down as you prefer.

??? Clock

This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change.

??? Phase

This function allows you to remove any horizontal noise and clear or sharpen the image of characters.

Reset

This function allows you to return to the good picture reproduc- tion programmed at the factory and cannot be changed.

Note : Some signal from some graphics boards may not func- tion properly. If the results are unsatisfactory, adjust your moni- tor???s position, clock and phase manually.

5. Press the OK button to store it for the PC monitor picture.

Connection of PC

ENGLISH

Selecting wide XGA mode

To see a normal picture, match the resolution of RGB mode and selection of XGA mode.

1.Press the MENU button and then D / E button to select the

Screen menu.

2.Press the G button and then D / E button to select XGA mode.

3.Press the G button and then D / E button to select the desired XGA resolution.

4.Repeatedly press the MENU button to return to normal TV viewing.

PSM SSM

PR

PR

ARC

/

40

Picture format

You can watch TV in various picture formats; Spectacle, Original, 4:3, 16:9, 14:9, Zoom1, Zoom2.

Repeatedly press the ARC button to select your desired picture format.

Spectacle

When your TV receives the wide screen signal, it will lead you to adjust the picture horizontally, in a nonlinear proportion, to fill the entire screen.

Original

When your TV receives the wide screen signal, it will be automatically changed to the picture format to be sent. (Not available in all countries)

4:3

This picture format is 4 to 3 of general TV.

16:9

You can enjoy the cinema (the picture format of 16:9) or general TV programme through the 16:9 mode.

The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full.

14:9

You can enjoy the picture format of 14:9 or general TV programme through the 14:9 mode.

The screen 14:9 is viewed just like that the screen 4:3 is magnified to the upper / lower and left / right.

Zoom1

Following selection will lead you to view the picture without any alterna- tion, while filling the entire screen. However, the top and bottom portions of the picture will be cropped.

Zoom2

Choose Zoom2 when you want the picture to be altered, both hor- izontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage.

Note :

a.ARC menu is not available in RGB, HDMI, Component mode

exept 4:3, 16:9. You cn adjust the enlarge proportion using D / E button.

b.This feature is not available for all models.

Troubleshooting Checklist

The video function does not work.

???Check whether the product is turned on.

???Try another channel. The problem may be with the broadcast.

No picture & ??? Is the power cord inserted into wall power outlet?

No sound ??? Check your antenna direction and/or location.

???Test the wall power outlet, plug another product???s power cord into the outlet where the product???s power cord was plugged in.

ENGLISH

Product Specifications

*The specifications shown above may be changed without prior notice for quality improvement.

* The specifications shown above may be changed without prior notice for quality improvement.

ENGLISH