For Customer Support/Service, please call:

1-888-865-3026

The latest product information and documentation is available online at:

www.LGsolutions.com/products

MODEL and SERIAL NUMBER

The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:

Model No._________________Serial No. _______________

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accor- dance with the manufacturer???s instructions.

8.Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11.Only use attachments/accessories specified by the man- ufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the appara- tus. When a cart is used, use caution when moving the cart/apparatus combination in order to avoid injury from tip-over.

PORTABLE CART WARNING

13.Refer all servicing to quali???ed service personnel. Servicing is required when the apparatus has been dam- aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14.Never touch this apparatus or antenna during a thunder or lighting storm.

15.When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.

16.Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.

17.Power Cord

Caution: It is recommended that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of the Owner???s Manual to be certain.

Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not use a damaged or loose power cord. Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

18.Overloading

Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or dam- aged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in ???re or electric shock.

19.Outdoor Use/Wet Location

Warning: To reduce the risk of ???re or electrical shock, do not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this prod- uct near ???ammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place objects ???lled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).

20.Grounding

Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., a TV with a three-prong ground- ed AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

21.Disconnect Device

The mains plug is the disconnecting device. The plug must remain readily operable.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.

(Continued on next page)

(Continued from previous page)

22.Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead- in wire to an antenna-discharge unit, size of grounding con- ductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

23.Cleaning

When cleaning, unplug the power cord and rub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

24.Transporting Product

Make sure the product is turned Off and unplugged and that all cables have been removed. It may take two or more peo- ple to carry larger TVs. Do not press against or put stress on the front panel of the TV.

25.Ventilation

Install the TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.

26.Do not touch the ventilation openings, as they may become hot while the TV is operating.

27.If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord, and contact an authorized service center.

28.Do not press strongly on the panel with a hand or sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.

29.Keep the product away from direct sunlight.

30.Dot Defect

The Plasma or LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you???re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

31.Generated Sound

???Cracking???: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal con- traction due to temperature and humidity. This noise is com- mon for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which sup- plies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

32.For LCD TV

If the TV feels cold to the touch, there may be a small ???flick- er??? when it is turned On. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor???s per- formance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 ??? 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup Checklist / Overview . . . . . . . . . . . . . . . . . . . . . . 6 Pro:Centric TV Interactive Menu Features. . . . . . . . . . . 7 LD320H/LD325H Rear Jack Panel . . . . . . . . . . . . . . . . 8

Side Connections Panel / RF Antenna & MPI Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installer Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installer Remote Control Typical Key Functions . . . . . 11 Commercial Mode Setup for Master TV. . . . . . . . . 12 ??? 13 Installer Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ??? 20 TV Setup Menus Overview . . . . . . . . . . . . . . . . . . . . . 21

Adding Channel Icons / Custom Channel Labels

(2-5-4 + MENU Mode) . . . . . . . . . . . . . . . . . . . . . . . . . 22 FTG Mode of Operation . . . . . . . . . . . . . . . . . . . . . 23 ??? 26 FTG Setup Overview . . . . . . . . . . . . . . . . . . . . . . . . 23

Determining the TV Operating Mode / FTG

Channel Map Configuration Utility Overview . . . . . . 24

FTG Channel Map Configuration Utility / FTG

Channel Map Editor Overview . . . . . . . . . . . . . . . . . 25 FTG Installer Menu Configuration Utility Overview. . 26 Cloning Overview / Clonable Menu Features . . . . . . . 27 Cloning Procedures . . . . . . . . . . . . . . . . . . . . . . . . 28 ??? 32

Learning / Teaching a Master TV Setup using

a USB Memory Device . . . . . . . . . . . . . . . . . . . . . . . 28

Learning / Teaching a Master TV Setup using

a TLL-1100A Clone Programmer . . . . . . . . . . . . 29 ??? 30

Learning / Teaching a Master TV Setup using

an LT2002 Clone Programmer . . . . . . . . . . . . . . 31 ??? 32 Remote Jack Pack / TV Connections & Setup . . . . . . 33

References

Upgrading TV/PTC Software using a USB Memory Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Downloading a Splash Screen using a USB Memory Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Power Consumption Settings. . . . . . . . . . . . . . . . . . . . 36 TV Camport Auto Sense Operation . . . . . . . . . . . . . . . 37 TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . 38 b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . 39 RJP Model List and Input Auto-sensing Hierarchy. . . . 40

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 ??? 44

General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . 41

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . 42

Commercial Mode Check / FTG Operating

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Clone Programmer Troubleshooting . . . . . . . . . . . . . 44

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Document Revision History / Notes . . . . . . . . . . . . . . . 46

Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setup Checklist

Installation and Setup Checklist

__ Unpack TV and all accessories. __ Install batteries in remote control. __ Install TV on VESA mount or stand.

Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate.

Hardware Connections

__ Install any additional hardware as appropriate to your institution, LAN, etc.

Cable Connections

__ Make all connections to rear jack panel and RF antenna on MPI/PPV card.

__ Make all connections to signal, interactive resources, and Aux sources, as appropriate.

Commercial Mode Setup

__ Complete Commercial Mode Setup (configure all relevant Installer Menu items as required of your institution and configure display features for the end user).

Software Installation

__ Install or configure any software, as applicable, for example, PPV, etc.

Channel Guide

Information

Remote Help

Watch TV

ALARM TIMER INPUT

TV

1 2 3

4 5 6

7 8 9

0 FLASHBK

INFO i

P

VOL PORTAL CH A

G

E

MUTE

MENU GUIDE CC

ENTER

BACK SAP EXIT

EJECT

RATIO

Important: Pro:Centric operation requires that Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be in PPV or FTG Mode.

The interactive Pro:Centric TV enables guests???from the comfort of their hotel rooms???to view and select from a complete listing of hotel services and amenities. The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities charges are billed at the time of order.

Interactive amenities may include:

???Hotel information, news, and events

???Directory services (tourist attractions, restaurants, etc.)

???Reservation services (business meetings, ???tness, spa, etc.)

???Weather and traf???c information

???Shopping services (delivery to guest room)

???Room service (menu ordering, memo service, morning wake up call, laundry, etc.)

???Ticketing services

???Check-out service (in the guest room)

???Gaming services

???E-mail resources/account access

Use the Installer Remote to operate both interactive menus and regular TV features. Press PORTAL on the Installer Remote to access the interactive menus.

Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.

Channel Guide

Shows available TV networks and channels. When available, Electronic Program Guide (EPG) data indicates the channel and the program start and ???nish times.

Information

Typically displays hotel information, for example, photos of guest rooms, dining rooms, business centers, ???tness and pool facilities, etc. Information may also include resourc- es, such as local school programs, run in cooperation with the hotel.

Remote Help

Provides help for navigating the interactive menus.

Watch TV

Removes the interactive menu from the screen and returns to the previously tuned TV channel.

RJP

Connection for Remote Jack Pack (RJP) Control cable.

UPDATE

Restricted to software updates.

RESET

Press RESET to re-initialize the TV.

AUDIO IN (RGB/DVI)

Audio connection for

RGB or DVI device.

REMOTE CONTROL OUT

IR output for controlling an auxiliary device.

AUDIO/VIDEO IN 1

Connection for composite audio/ video output from external device.

COMPONENT IN

ANTENNA IN

26LD320H only. Connect to Antenna/ CATV.

RS-232C IN

Use for downloading software updates, etc.

TV-LINK CFG

Use for local FTG configuration.

HDMI/DVI IN

Connection for HDMI/DVI output from external device.

RGB IN (PC)

Connection for RGB output from PC.

COMPONENT IN

Connection for component output from external device.

SPEAKER OUT (8??) ** Connect to 8 ohm self-powered

speaker input. Intended for special applications, such as a powered bath- room speaker with volume control.

GAME CONTROL *

EBL in LodgeNet PPV Mode only.

Side Connections Panel

USB IN

Insert USB memory device for software updates, cloning pur- poses, or picture/music enter- tainment, as applicable.

USB IN

VIDEO L/MONO -AUDIO- R

AV IN 2

A/V 2 Input

L/MONO-AUDIO-R IN

Connect to audio output jacks on external device. For only mono audio output, connect to Left audio input.

VIDEO IN

Connect to video output port on external device (see Reference section, ???TV Camport Auto Sense Operation,??? for further information).

RF Antenna & MPI Connections

(32/37/42LD320H and 32/37LD325H TVs)

Note: 26LD320H Antenna and MPI connections are on the rear jack panel (see previous page).

Antenna

or CATV

IN ANTENNA

I MP

ANTENNA IN

Connect to

Antenna/CATV.

MPI

Enables an external MPI control device (i.e., clone programmer, VOD/ PPV STB, etc.) to control the TV when the EBL is in Pass-through Mode.

This is the Commercial Mode Setup Guide only.

Installer Menu / Commercial Mode Setup

To set up a Master TV, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. Similarly, to configure a single TV???s Installer Menu settings in FTG Mode, you will need to know how to access and use the FTG Configuration Application utilities. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to page 14 for informa- tion on accessing the Installer Menu in Pass-through Mode. Refer to page 23 for information on accessing the FTG Installer Menu Configuration Utility in the FTG Configuration Application. Pages 15 to 20 describe Installer Menu items in detail.

Installer Remote

The LG Installer Remote is supplied with and dedicated to operate the TV. See next page for typical key functions in TV operating mode. Some DVD and VCR controls may be available for selected LG DVD/VCR products.

Cloning

Cloning refers to the process of capturing a Master TV Setup and trans- ferring it to a Target TV. The Master TV???s clonable features need to be configured as part of the Commercial Mode Setup. This is a critical step. If the Master TV???s clonable features???channel icons or labels, digital font options, etc.???are not set up correctly, the cloned TVs will all have prob- lems. Pages 27 to 32 provide detailed information on cloning require- ments and procedures.

+

Installing Batteries in Installer

Remote

???Open the battery compartment cover on the back side of the remote.

???Install two high-quality alkaline 1.5V AAA batteries. Never mix old or used batteries with new ones. Install batteries matching correct polarity as shown (+ with + and - with -).

???Replace the battery compartment cover.

XXLD320H PTC INSTALLER MENU

Typical Installer Menu

ALARM TIMER INPUT

TV

1 2 3

4 5 6

7 8 9

0 FLASHBK

INFO i

P

VOL PORTAL CH A

G

E

MUTE

MENU GUIDE CC

ENTER

BACK SAP EXIT

EJECT

RATIO

POWER Turns TV On or Off.

ALARM Sets the time when the TV will automatically turn itself ON.

TIMER Sets the amount of time before the TV automatically turns itself OFF.

INPUT Selects RGB, HDMI/DVI1, HDMI2, Component Input, AV1, and AV2 sources.

TV Returns to the last TV channel.

VOLUME UP/DOWN Increases/decreases sound level.

INFO Displays channel information.

PORTAL Displays and removes the interactive menu.

MUTE Switches sound ON or OFF.

CHANNEL UP/DOWN Selects available channels found with Auto Tuning. Moves to next available page in electronic program guide.

Color buttons access special functions in some menus.

VCR/DVD BUTTONS Controls some video cassette recorders or DVD players.

EJECT Ejects a USB memory device, CD, DVD, VHS tape, as applicable.

1.Set Installer Menu items.

a)Use the Installer Remote to enter the TV Installer Menu: Press MENU repeatedly until the on-screen menu locks up, and then press 9-8-7-6 + ENTER. Refer to pages 14 to 20 for detailed information on Installer Menu items.

b)Set Installer Menu item 117 FACT DEFAULT to 001 and press ENTER on the Installer Remote.

This clears all Installer Menu custom settings, channel labels/ icons, etc. and reloads the factory default settings. The value will change back to 0 after the internal TV controller (Protocol Translator Card [PTC]) has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active Channel List.

c)Set Installer Menu item 003 BAND/AFC, as appropriate.

???Broadcast: Set to 000.

???CATV: Set to 001 (default).

???HRC: Set to 002.

???IRC: Set to 003.

d)Set any other Installer Menu items that affect your TV program- ming network to the required con???guration. For example, en- able/disable Aux sources, set a Start Channel, etc.

e)After you have adjusted all required Installer Menu item set- tings, press ENTER on the Installer Remote to exit the menu and save your changes.

2.Set up TV features.

On-screen setup menus control the features of the TV (see page 21). Press MENU on the Installer Remote to access the setup menus, and then set Channel, Picture, Audio, Lock, Time, etc. options to the desired configurations. See also the Clonable Menu Features list on page 27.

Note: If desired, you can run Auto Tuning (see step 3) prior to completing this step.

XXLD320H PTC INSTALLER MENU

Typical TV Installer Menu

Note: The Installer Menu header will vary depending on the TV you are setting up.

Adjust the settings for these

Installer Menu items.

Set the TV features to the desired configuration for the end user.

(Continued on next page)

(Continued from previous page)

3.Run Auto Tuning (Channel Search).

a)Search for all available analog and digital channels: Go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

b)Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only.

???Add/delete channels per your system requirements. Note that physical channel numbers are used to identify virtual channels. Also, channel numbers cannot be higher than 255.

???Use the Channel Label option in the Channel Menu to add familiar channel trademarks/logos such as ABC, CBS, NBC, etc. to the Channel-Time on-screen display. Identi???able labels (logos) should enable the end user to readily know what com- mon networks are available. (You can add the channel labels in this step, or you can add channel logos or labels for channels without icons in step 5.)

4.Transfer the TV Setup to the internal TV Controller (PTC): 2-5-5 + MENU Mode

After the TV channel lineup has been edited and channel label icons added, enter the Installer Menu. Once in the Installer Menu, press 2-5-5 + MENU on the Installer Remote to initiate the transfer of the Master TV Setup to the PTC. Once the transfer is complete, the TV will exit the Installer Menu.

Note: The maximum number of active channels that can be trans- ferred is 141. Total channels numbering more than 141 will result in erratic TV operation.

5.Add Custom Channel and Aux Source Labels for Analog Channels: 2-5-4 + MENU Mode

Enter the Installer Menu, and press 2-5-4 + MENU on the Installer Remote. Add/edit custom text labels to channel on-screen displays. Note that digital channels often have a broadcaster generated label (see 2-5-4 + MENU procedural information on page 22). When you are finished, press MENU to exit 2-5-4 + MENU Mode.

6.Verify the TV setup.

At this point, verify that the channel lineup, channel icons, and cus- tom labels are correct. Make sure the TV features are set per your requirements.

7.Lock the channel lineup.

Enter the Installer Menu, and set item 028 CH. OVERIDE to 000 to lock the channel lineup and restrict access to the TV setup menus.* Press ENTER to exit the Installer Menu and save your changes.

The Master TV Setup is now ready to be copied to a clone programmer (see cloning information in this document).

Run Auto Tuning, edit channels, and select familiar channel trademarks/logos using Channel Menu options.

DIGITAL 19-3

MONO STEREO SAP

WXYZ

Custom Text Label ???WXYZ??? created in 2-5-4 + MENU (Add Channel Label) Mode.

After verifying the TV Setup, set Installer Menu item 028 CH. OVERIDE to 000.*

* This step prevents end users from accessing channel settings (i.e., the Channel Menu will be inaccessible/ grayed out).

Accessing the Installer Menu

Make sure the TV is ON. Using an Installer Remote, press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER to access the Installer Menu.

The Installer Menu opens with item 000 INSTALLER SEQ 000. Use the Up/ Down arrow keys to sequence through the available menu items, or access an item directly by keying in the line number and then pressing MENU. For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU. To change a setting, use the Left/Right arrow keys, or enter a value directly.

Using the Installer Menu

XXLD320H PTC INSTALLER MENU

Typical TV Installer Menu

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Speci???es entry sequence to the Installer Menu.

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 rep- resenting the hours that the unit will remain ON, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, this allows the TV to turn ON when AC power is ap- plied. Pressing the ON button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is the default (OFF), and 1 is ON.

Note: If set to 1 (ON), the TV does not respond to On/Off com- mands from either the remote or the display control panel, and the SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are four possible settings for this option:

If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here, and add the channels using the Channel Edit option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial Major Start Channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would al- ways select that channel when it is turned ON. Setting this item to 255 causes the last channel viewed when the TV was turned OFF, to be the tuned to channel when the TV is turned ON again.

Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

005 - CHAN LOCK (Channel Lock)

Channel Lock is ideal if the system must always be on the same channel. Changing channels with the Channel Up/Down or key- pad numbers is impossible. Channel Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with STRT CHAN- NEL (Installer Menu item 004) where the Start Channel may, for example, be set to 3 or 4. If the Start Channel is 3, then the TV will remain locked on channel 3.

NOTE: For items 007, 008, and 009

For legacy reasons, the scale used is 0 ??? 63. The PTC software will translate this to the 0 ??? 100 scale used by the TV.

To translate a TV volume level to the Installer Menu value, use the following formula:

Installer Value = TV Value x 63 100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always

select that volume level when it is turned ON. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned OFF; at turn ON, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63. Use the Left/Right arrow keys to change values. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV.

Note: The minimum volume level cannot have a value setting higher than the maximum volume level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume level high enough to disturb oth- ers. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Use the Left/Right arrow keys to change values. It may be best to set the same value on every TV.

Note: The maximum volume level cannot have a value setting lower than the minimum volume level (described above).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, KEY DEFEAT prevents the end user from accessing the on-screen menus from the display panel???MENU, ENTER, and menu navigation keys do not function. If set to 0, those keys do function.

Note: Users can always access the menus by pressing MENU on the remote.

015 - SLEEP TIMER

If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers) *

If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers.

Note: Clock must be set in order to use timers.

017 - ALARM *

Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.

Note: Clock must be set before the Alarm function will work.

020 - FEATURE LEVEL

Determines the IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on ???bed number??? in a multi-TV single room installation. First determine the IR mode; then select the bed number.

IR Mode 0 = Legacy

IR Mode 1 = Multi-code remote

Note: For further information, see documentation for the accessory package that includes the multi-code remote.

021 - V-CHIP (Parental Control) *

Set to 1 to activate V-Chip (Parental Control) and have it available to the end user to ???lter and control or otherwise restrict program- ming content that can appear. Set to 0 to turn the V-Chip feature Off (not available to user); no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours) *

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

023 - CAPTION LOCK

If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting con???gured before the TV was turned OFF when the TV is turned ON.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the TV???s memory can be selected.

029 - OLD OCV (On Command Video???)

Set to 1 for operation with systems from On Command Corporation.

* Only affects Function Menu if enabled by some PPV providers.

030 - ACK MASK

MPI Communication Parameter. Leave at default setting unless changed by PPV provider. When set to 1, changes MPI for some OCV boxes.

031 - POLL RATE

MPI Communication Parameter. Selects Poll Rate for MPI. Leave at default setting unless changed by Pay-Per-View provider. Step size of 16 ms.

032 - TIMING PULSE

MPI Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS.

034 - CAMPORT EN. (Camera Port Enable)

Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

035 - COMPPORT EN. (Computer Port Enable)

Enable/disable TV display panel HDMI 1 input jack. Set to 0 to disable HDMI1. Set to 1 to enable HDMI1.

Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.

040 - AUTO CAMPORT

Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection.

Note: If set to 1, item 093 RJP AVAILABLE is automatically set to 0.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting Aux source. When turned ON, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.

If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO

047 - AUX STATUS

Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identi???cation change. Controls MPI status channel response for Aux inputs.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display; Channel-Time dis- play will not appear. Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Note: Applies only to ???Channel Not Available??? message if item 073 is set to 1 (enabled). If foreground color and background color are the same, the menu background will be transparent.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

Note: Applies only to ???Channel Not Available??? message if item 073 is set to 1 (enabled). If foreground color and background color are the same, the menu background will be transparent.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a ???NOT AVAIL- ABLE??? message is displayed when directly accessing a channel not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automati- cally tunes to the speci???ed Start Channel.

078 - UPN MSB (UPN Most Signi???cant Byte)

User programmable number, most signi???cant byte readable by MPI command. Not linked to serial number.

079 - UPN MSB-1 (UPN Most Signi???cant Byte-1)

User programmable number, most signi???cant byte-1 readable by MPI command. Not linked to serial number.

080 - UPN MSB-2 (UPN Most Signi???cant Byte-2)

User programmable number, most signi???cant byte-2 readable by MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Signi???cant Byte)

User programmable number, least signi???cant byte readable by MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PC- based Windows controlled systems. Range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Paren- tal Control restrictions permanently. Set to 0 for user-speci???ed hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable for PC RGB input. Set to 17 to initiate a one-time automatic con???guration after an AC power cycle; other- wise, automatic adjustment will be performed each time the RGB input is accessed.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

090 - KEY LOCK

If set to 1, front keyboard Channel, Volume, and Captions buttons are disabled, Power button remains enabled. If set to 0, the Chan- nel, Volume, Captions, and Power buttons are all enabled.

091 - YPrPb2 EN. (HDMI2 Enable)

Set to 0 to disable display panel HDMI2 input. Set to 1 to enable DTV mode. Set to 2 to enable PC mode.

093 - RJP AVAILABLE (Remote Jack Pack Available)

???0 = Remote jack pack is not available or disabled.

???1 = Legacy Model RJPs: HDMI Mode

Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

???2 = Legacy Model RJPs: DVI Mode

Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via a separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

???5 = Scaler Model RJPs: HDMI Mode

Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

???6 = Scaler Model RJPs: DVI Mode

Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connect- ed to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

Notes:

See Reference section, ???RJP Model List and Input Auto-sensing Hierarchy.??? If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040 AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6 allow the lodge staff to customize each TV???s RJP setup based on customer requirements.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function Menu, if Function Menu is available. Set to 0 to disable SAP feature on Function Menu, if Function Menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up.

???Set to 0 for Set By System.

???Set to 1 for 4:3.

???Set to 2 for 16:9 (Factory Default).

???Set to 3 for Just Scan.

???Set to 4 for Zoom.

Note: Only applies if item 106 ASP RATIO LOCK is disabled, set to 0.

098 - PRO:CENTRIC

Selects the Pro:Centric Mode. Set to 0 (default) to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 100.

???1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

???101 - 200 Dynamic Back Lighting

(101 = Dimmest picture, 200 = Brightest picture)

If set between 101 and 200, the TV automatically controls back lighting depending upon the picture level of the current program. If set to 255, back lighting is controlled via the Picture settings in the TV???s setup menus.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel???s Minor Start Channel number.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for Normal. Set to 1 for Blank.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal. Set to 1 to load presets of all Installer Menu item settings.

Warning: If set to 1, this will reload the factory de- faults and clear the Channel List, including any assigned channel icons and custom channel labels.

118 - POWER SAVINGS

Default is set to 3. When the TV is in Standby mode, the MPI card slot is powered by the Standby power supply and embed- ded b-LAN is not powered. When the TV is in Power On mode, the MPI card slot is powered by the main 12V power supply and embedded b-LAN is powered. Note that the TV must be turned ON in order to communicate with the Embedded b-LAN module for con???guration and control when POWER SAVINGS is set to 3.

Note: MPI cards with b-LAN technology???LMT7Z5, LMT7Z7, LMT7Z9???are NOT supported on TVs in which the b-LAN module is embedded.

???1 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN is always powered.

???3 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN is only powered when the TV is turned ON.

???7 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN (including the Pro:Centric data tuner) is never powered.

Note: See Reference section, ???b-LAN Setup & Overview,??? for further information.

119 - DATA CHANNEL

Set to 0 (default) to disable. Set to the RF channel number of the Data Channel for Pro:Centric or E-Z Installation (splash screen, configuration, or firmware) data.

Note: Pro:Centric updates are downloaded from the Pro:Centric server to the TV when the TV is turned OFF. Also, while Pro:Centric updates are in progress, it is not possible to turn the TV ON. The TV may take several minutes to load EPG data after the initial download of the Pro:Centric application. Subsequent updates generally will take less than one minute.

Editing/Adding Channel Icons and/or Labels

If there is no pre-assigned icon, you can make a custom channel label of up to seven (7) characters to help identify a channel or network. If desired, channel labels can also be added in addition to a pre-assigned icon. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

Editing and adding the labels can only be done if there are channels entered into the TV???s Channel Map either during Commercial Mode Setup (see pages 12 to 13), by cloning, or by using some PPV provider???s master remote controls. Note: A blank letter space is available between ???Z??? and ???!???.

To perform channel editing/labeling:

1. Enter the TV Installer Menu.

(Icon)

XYZ

XYZ XYZ

NETWORK

2.Press 2-5-4 + MENU on the Installer Remote to enter the Channel Label Editing Mode.

3.Add channel icons and channel labels as described in the procedures below. (You can do this more than once.)

4.To exit the menu when you are done, press MENU.

1 2 3 4 5 6 7

(Label)

Changing a Channel???s Icon on the Master TV

1.Use Channel Up/Down to select the channel for which to change the icon.

2.Use the Left/Right arrow keys to select the thin letter ???I??? on the Channel ID display.

3.Use the Up/Down arrow keys to select the icon with which you want to identify the channel. (If you know the icon number, enter the number, and press ENTER.)

4.Proceed to change/add channel labels, or go to the next channel.

Changing/Adding Channel Labels on the Master TV

1.Use Channel Up/Down to select the desired channel.

2.Press the Left/Right arrow re- peatedly until the numbers 1 to 7 appear on the display. The number shows the position of the character that can be changed. Number 1 is the ???rst character, number 2 the second character, etc.

3.Use the Up/Down arrow keys to select the desired character.

4.Proceed to the next number posi- tion, or use Channel Up/Down to go to the next channel.

Changing Source Labels on the Master TV

1.Press INPUT to select the desired Aux input source: A/V 1, A/V 2, HDMI Component, RGB, etc.

2.Press the Left/Right arrow re- peatedly until the numbers 0 to 9 appear on the display. The number shows the position of the character that can be changed.

3.Use the Up/Down arrow keys to select the desired character.

4.Press INPUT for the next Aux source, or proceed to change an icon or change/add labels. Use Channel Up/Down to return to channels.

???Channel Up/Down: Tunes in the next channel in scan.

???Left/Right Arrows: Select the item to change. If ???I??? is shown, the icon can be changed. If a number is shown, it indicates the position of the character that can be changed.

???Up/Down Arrows: Select the icon or the character to be

displayed. Tip: Arrows can be held down for fast scrolling.

???0 ??? 9: Use to enter the index number of the icon, if known.

???ENTER: Changes the icon after the number has been entered.

???INPUT: Changes the Aux input label.

???MENU: Exits the editing process.

To determine the operating mode of the

TV, press MENU on the Installer Remote. If the end user Function Menu (showing aspect ratio options???see below) appears, the TV/EBL is in FTG Mode. If the TV setup menus appear, the EBL is in Pass- through Mode.

ABC

Set By Program

4:3

16:9

Zoom

Just Scan

Function Menu

Shows that the EBL is in FTG Mode. While this menu is present on-screen, Installer Menu settings can ONLY be accessed/changed using the FTG Configuration Application.

The following pages provide overviews of the FTG Channel Map and FTG Installer Menu Configuration Utilities that comprise the FTG Configuration Application. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information.

PRINT MAP

Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or Text file.

EDIT/ADD MAP

Click to open the FTG Channel Map Editor to create or edit an FTG Channel Map (see next page).

WRITE

Click to transfer the FTG

Channel Map to the EBL.

READ

Click to transfer the FTG Channel Map from the EBL to the FTG Configuration Application.

* Logical Channel numbers will automatically be assigned in ascending order, starting with 0

(zero), to the Physical Channels from the TV Channel Map.

LOGICAL CHANNEL MAPPING

Select a Logical Channel number, then assign it the RF, Major, and Minor chan- nel numbers to complete the mapping.

DELETE

Click to remove highlighted channel from FTG Channel Map.

ADD

After defining a new Logical Channel, click to add channel to the FTG Channel Map.

UPDATE

After editing an existing Logical Channel???s data, click to commit the changes in the FTG Channel Map.

EXIT

Click to exit editor and return to FTG Channel Map Configuration Utility.

CONFIGURATION SETTINGS

Select tabs for categories of Installer Menu items to set up TV.

HOSPITAL-GRADE TV ONLY

Set Hospital items on Installer Menu for hospital-grade TVs.

INSTALLER DEFAULTS

Click to reset FTG Installer Menu items shown in the FTG Configuration Application to defaults.

IR REMOTE ACCESS

Toggle IR Remote Access to ON to obtain access to TV setup menus and Installer Menu.

WRITE

Click to transfer the FTG Installer

Menu settings to the EBL.

LEARN

Click to transfer Installer

Menu settings from the

PTC to the EBL and FTG

Configuration Application. *

READ

Click to transfer the Installer Menu settings in the EBL to the FTG Configuration Application.

IMPORTANT CLONING INFORMATION

There are three options for cloning a Master TV Setup:

???Using a USB memory device

???Using a TLL-1100A clone programmer

???Using a LT2002 clone programmer

Each option is described in further detail on the pages that follow. As you perform cloning procedures, be sure to com- plete each task as indicated. If a procedure or step is omit- ted or not performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows the proper message when cloning. If the message indicat- ed does not appear, there is a problem with that step, and cloning may not be successful.

Warning: Copying a blank or incorrect memory into a TV will cause the TV to operate erratically or become inoperable.

Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not cer- tain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Before you begin cloning:

???Complete the Commercial Mode Setup procedure on pages 12 to 13.

???All equipment should be connected to power and turned ON.

???Learning and Teaching is only possible between identical model TVs.

???For both Master and Target TVs???The TV EBL must be in Pass-through Mode.

???If using a USB memory device, ensure the USB device has been formatted with FAT format.

???For both Master and Target TVs???If using a clone pro- grammer, ensure the TV signal source is either an Aux or TV (RF) source. If a TV (RF) source, the TV must be tuned to an analog (not a digital) channel.

???LT2002 only???Make sure the batteries in the clone pro- grammer are fresh. If batteries are removed, the clone programmer clock time (if set) will be lost (see page 32 for information on the clone programmer clock).

???Do not unplug the TV power cord or remove/disconnect the USB memory device/clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction or harm the USB device/clone programmer, respectively.

Learn Setup from Master TV

1.Ensure the Master TV is set up completely and the EBL is in Pass-through Mode.

2.Plug the USB memory device into the USB IN port on the Master TV.

3.Press MENU to display the TV setup menus.

4.Use the arrow navigation keys to select/highlight the Option menu icon; then, press the number ???7??? key a total of seven times to display the USB Download Menu.

5.To gain access to the Learn From TV option in the USB Download Menu, key in the password used to enter the Installer Menu (Example: Press 9-8-7-6).

6.Use the Up/Down arrow keys to select Learn From TV and press ENTER.

7.To identify the pro???le from others, you can use the Up/Down arrow keys to change the last ???ve digits of the ???lename. Press ENTER when you are ready to initiate Learning.

Learning status will be shown on the progress bar. When the Learning process is complete, the USB Download menu will reappear on screen.

8.Remove the USB memory device.

Teach Master TV Setup to Target TV

1.Ensure the Target TV EBL is in Pass-through Mode, and then plug the USB memory device with the Master TV Setup ???le into the Target TV USB IN port.

2.Press MENU to display the TV setup menus.

3.Use the arrow navigation keys to select/highlight the Option menu icon; then, press the number ???7??? key a total of seven times to display the USB Download Menu.

4.Use the Up/Down arrow keys to select Teach To TV and press ENTER.

5.Use the Up/Down arrow keys to select/highlight the Master TV Setup you want to install and press ENTER. Note: Filenames identify the TV and the TLL version (see example at right).

Teaching status will be shown on the progress bar. When the Teaching process is complete, the USB Download menu will reappear on screen.

6.When Teaching is done, remove the USB memory device, turn OFF the TV, and unplug the TV power cord for 15 seconds.

7.Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV

Learn From TV

Previous Enter

Learn From TV

Select the ???le name and press OK to start

!Learn From TV

UPDATING...

25%

Do not remove the USB from the port!

Do not unplug!

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV

Learn From TV

Previous Enter

Teach To TV

xxLD320H-UA00001.TLL

Previous Enter

!Teach To TV

UPDATING...

50%

Do not remove the USB from the port!

Do not unplug!

Cloning is accomplished using the TV/ clone programmer MPI ports for com- munication (see figure).

TLL-1100A Cloning Notes

???Read the IMPORTANT CLONING INFORMATION on page 27 before beginning any cloning procedures.

???Ensure the TLL-1100A is either fully charged or connected to AC power.

???Learning and Teaching is only possible between identical model TVs; however, the TLL-1100A clone programmer can store up to eight different Master TV Setups.

Learn Setup from Master TV

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

TLL-1100A Clone

TLL-1100A

1.Ensure the Master TV is set up completely and the EBL is in Pass- through Mode.

2.If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the TV MPI port.

3.Turn ON the TLL-1100A.

4.Use the MODE button on the TLL-1100A to select Clone Mode.

5.Use the Left/Right arrows on the TLL-1100A to select the Memory CBank (1 to 8) in which to store the Master TV Setup.

6.Plug the other end of the MPI cable into the MPI port on the bottom of the TLL-1100A. The Clone Selection Menu will display on the TV screen.

7.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu. Then, press ENTER to transfer the Master TV Setup into CBankX on the TLL-1100A.

Learning usually takes about 90 seconds. ???LEARNING IN PROGRESS??? will be displayed on the screen while the TLL-1100A copies the Master Setup. When the Learning process is complete, a ???LEARNING COM- PLETE??? message will be displayed.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

-To change menu items, press channel keys or digits.

-To execute item, press Enter.

(Optional) Set the Clock

Set the time on a Master TV???s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV???s clock by copying the time from the clone programmer.) The TLL- 1100A can copy the current time to both a Master TV and to the clone???s internal clock???accurate to within one minute.

Since the TLL-1100A???s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the TLL-1100A clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1.When Learning is complete, disconnect the MPI cable from the Master TV.

2.Ensure the Target TV EBL is in Pass-through Mode and the TV is tuned/ set to an analog channel or Aux source, and then connect the MPI cable to the MPI port on the Target TV. The Clone Selection Menu will display on the TV screen.

3.Ensure the correct Memory CBank(X) is selected on the TLL-1100A.

4.Press 2 on the Installer Remote to select TEACH TO TV from the Clone Selection Menu. Then, press ENTER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. ???TEACHING IN PROGRESS??? will be displayed on the screen during Teaching. When the Teaching process is complete, a ???TEACHING COMPLETE??? message will be displayed.

5.When Teaching is done, disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.

6.Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2)TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

-To change menu items, press channel keys or digits.

-To execute item, press Enter.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

-To change menu items, press channel keys or digits.

-To execute item, press Enter.

MPI

Cable

???Read the IMPORTANT CLONING INFORMATION on page 27 before beginning any cloning procedures.

???A slow ???ashing green light indicates that there are communication problems between the TV and the LT2002 clone

programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

???If the status indicator is red, the LT2002 batteries are low and should be re-

placed. Install four (4) high-quality alkaline AA batteries.

???Learning and Teaching is only possible between identical model TVs; however, the LT2002 clone programmer can store up to three different Master TV Setups.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REViSION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE

Ferrite Core (TDK, ZCAT 2035-0930)

LT2002 Clone

Programmer

MPI

Reset

$PMPS t
HSFFO






CBUUFSZ
PL t
SFE




CBUUFSZ
MPX

#MJOL
QBUUFSO t
TMPX







QPXFS
PO

no communications t
IFBSUCFBU


QPXFS
PO

communications ok

??

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

Learn Setup from Master TV

1.Ensure the Master TV is set up completely and the EBL is in Pass- through Mode.

2.If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the TV MPI port.

3.If there is a good connection after the LT2002 is connected to the TV MPI port, ???THE CLONE HAS CONTROL OF THE TV??? message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu (see sample screen on next page).

5.Select the clone Memory Bank in which to store the Master Setup by pressing either Channel key repeatedly to choose Memory Bank 1, 2, or 3. Note: If you choose a Memory Bank that already has a Master device???s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

(Continued on next page)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

(Continued from previous page)

6.Once you select the clone Memory Bank, press ENTER on the Installer Remote. The Memory Bank you selected will be shown.

7.Press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.

Learning usually takes about 90 seconds. ???LEARNING IN PROGRESS??? will be displayed on the screen while the LT2002 copies the Master Setup. When the Learning process is complete, a ???LEARNING COM- PLETE??? message will be displayed.

(Optional) Set the Clock

Set the time on a Master TV???s clock. (If the time has already been copied from a TV into the LT2002 clone programmer, you can set the Master TV???s clock by copying the time from the clone programmer.) The LT2002 can copy the current time to both a Master TV and to the clone???s internal clock???accu- rate to within one minute. (Another reason that the LT2002 should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the LT2002???s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the LT2002 clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1.When Learning is complete, disconnect the MPI cable from the Master TV.

2.Ensure the Target TV EBL is in Pass-through Mode and the TV is tuned/ set to an analog channel or Aux source, and then connect the MPI cable to the MPI port on the Target TV.

3.With ???THE CLONE HAS CONTROL OF TV??? message on display, press 2 on the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection Menu. Then, press ENTER.

4.Select the LT2002 Memory Bank in which the new setup is located. Then, press POWER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. ???TEACHING IN PROGRESS??? will be displayed on the screen during Teaching. When the Teaching process is complete, a ???TEACHING COMPLETE??? message will be displayed.

5.When Teaching is done, press any key on the Installer Remote to return to the Clone Selection Menu. Then, press ENTER.

SAVE TV SETUP IN SELECTED

CLONE MEMORY

(1)MEMORY 1 VER XX REV XX

(2)MEMORY 2 VER XX REV XX

(3)MEMORY 3 VER XX REV XX

(4)RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

COPY SELECTED CLONE MEMORY

TO TV

(1)MEMORY 1 VER XX REV XX

(2)MEMORY 2 VER XX REV XX

(3)MEMORY 3 VER XX REV XX

(4)RETURN TO CLONE MENU

6.Disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.

7.Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

COMPONENT IN

RGB IN (PC)

Connect RGB connector from RJP cable bundle (legacy RJP only).

HDMI/DVI IN 1

Connect HDMI connector from RJP cable bundle.

(26LD320H only)

(26LD320H only:

GAME CONTROL/MPI)

Checking the Software Versions

Note: This function is not accessible while the TV is in FTG or PPV Mode.

You can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu.

XXLD320H PTC INSTALLER MENU

Upgrading TV/PTC Software

Before you begin, note that the software upgrade ???les must be stored in a folder named ???LG_DTV??? in the root directory of the USB memory device. Also, ensure the USB device has been formatted with FAT format.

Note for TV Software Upgrade only: If the TV detects a later version of software on the USB device, it will automatically display a dialog from which you can start the software upgrade immediately. Otherwise, you can close the dialog, and access the USB Download Menu as described below.

1.Turn the TV ON.

2.Plug the USB memory device into the USB IN port on the TV.

3.Press MENU on the Installer Remote to display the TV setup menus.

4.Use the arrow navigation keys to select/highlight either the Option (if EBL is in Pass-through Mode) or Lock (if TV is in FTG or LodgeNet PPV Mode) menu icon; then, press the number ???7??? key a total of seven times to display the USB Download Menu.

5.Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade PTC Software, as applicable, and press ENTER.

6.Select the appropriate option(s), depending on the type of upgrade you are performing:

???TV Software Upgrade: (See screen samples at right.) Select TV Software Update from the ???rst TV Software Update window. In the second TV Software Update window, select/highlight the update ???le to install and press ENTER.

Note: Do not select Forced Update options unless you have been speci???cally instructed to do so or have previous experience with Expert Software Updates.

???PTC Software Upgrade: In the PTC Software Update window, select/highlight the update ???le to install and press ENTER.

Note: The PTC Software Update window is similar to the second TV Soft- ware Update window, though there are no Forced Update options. Current software version information is shown at the top and update ???les on the USB device are listed at the bottom of the window.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV

TV Software Update (Expert)

TV Software Update

LOGO Image Download

TV Software Update (Expert)

[ Current TV Software Version Information ]

EPK : 03.03.00

The following software files are found in the memory card. Select the file you want to download to this TV

or press EXIT to cancel the update.

EPK : 03.05.00

xxLD320H_v3_05_RevNo4204_USB

Splash Screen Image File Guidelines

???The splash screen image must be a baseline (not progressive) JPEG.

???The image should be no larger than 1 MB.

???The ideal size for the image is 1366 x 768 pixels or under.

???The image ???le must be stored in a folder named ???LG_DTV??? in the root directory of USB memory device.

???Ensure the USB device has been formatted with FAT format.

Downloading a Splash Screen Image

1.Turn the TV ON.

2.Plug the USB memory device into the USB IN port on the TV.

3.Press MENU on the Installer Remote to display the TV setup menus.

4.Use the arrow navigation keys to select/highlight either the Option (if EBL is in Pass-through Mode) or Lock (if TV is in FTG or LodgeNet PPV Mode) menu icon; then, press the number ???7??? key a total of seven times to display the USB Download Menu.

5.Use the Up/Down arrow keys to select Upgrade TV Software and then press

ENTER.

6.Select LOGO Image Download from the ???rst TV Software Update window.

7.In the second TV Software Update window, select/highlight the image ???le to download and press ENTER.

The TV will show download completion progress in a new window. Do NOT remove the USB device until the image download is complete. When the image download is complete, the TV will reset itself with an automatic restart. Upon the restart, you should see the new splash screen.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV

TV Software Update (Expert)

TV Software Update

LOGO Image Download

TV Software Update (Expert)

The following software files are found in the memory card. Select the file you want to download to this TV

or press EXIT to cancel the update.

Splash Image 1366 X 768 ProCentric

The Camport Auto Sense function is enabled when:

1.Installer Menu item 034 CAMPORT EN is set to 1 AND

2.Installer Menu item 040 AUTO CAMPORT is enabled (1).

Selectable: Can be accessed with INPUT key, direct access, etc.

Auto Sense: TV switches to this input when connector is inserted. The Camport (Side [AV IN 2] Video) has the highest priority and will override any commands including tuning to the Start Channel.

CAMPORT (Side Video) Functionality Control

Camport Operation (Stand-alone)

When Camport Auto Sense is enabled as above, the TV???s source will switch to the Side (AV IN 2) Video Aux source whenever a plug is inserted into the AV IN 2 Video input.

When the plug is removed, the TV will switch back to the previous channel or input source that was being displayed before the plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the Camport is active, then, when the video plug is removed, the TV will switch to the last requested channel. Source changes using any Source keys (INPUT) are ignored. Channel Up/Down and Flashback commands are not direct access tuning commands, and they are also ignored.

Camport Operation (FTG or PPV)

The operation will be similar to that of the Stand-alone Mode. However, when the Channel Map is maintained external to the PTC (i.e., FTG and PPV), Channel Up/ Down or Flashback keys are sent as Direct Access tuning commands to the PTC/TV.

Cannot direct enter channel number or ???No Signal??? appears.

Channel not included in channel lineup in TV controller.

After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available, it can be added to chan- nel lineup. If it is not available, the ???No Signal??? message appears on the TV screen.

Yes

Press POWER on

Installer Remote.

Yes

Press VOLUME UP/ DOWN or MUTE key on Installer Remote.

Press VOLUME UP/ DOWN or MUTE key on User-supplied Remote.

Bad

PPV Card

Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check

with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/ MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Reset Clone Programmer After Static Shock

After replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock:

???TLL-1100A: Turn the TLL-1100A OFF and then ON.

???LT2002: Use a paper clip or similar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal operation.

After a reset, check the real-time clock setting. It may be nec- essary to set the clone programmer clock from a TV contain- ing the correct time.

Notes

???The TLL-1100A and LT2002 clone programmers are designed to be used with TVs containing the 221-01006 and later pro- cessors. Use with earlier TVs may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability; they cannot display entire screens as shown in the setup instructions accompanying the clone programmer. Use the printed menu illustrations in the docu- mentation as an aid to making your programming choices.

???For both Master and Target TVs???The TV EBL must be in Pass-through Mode for cloning purposes. See also IMPORTANT CLONING INFORMATION on page 27.

Clone copies setup in less than 30 seconds.

Not enough time to copy entire TV setup.

TLL-1100A: Turn the TLL-1100A Off and then ON.

LT2002: Press RESET on clone programmer.

Then redo Learn/Teach. (Learning usually takes about 90 sec- onds; Teaching usually takes 3 to 4 minutes.)

Remote does not operate clone programmer.

Clone menu does not dis- play on TV screen, TLL- 1100A shows error mes- sage, or LT2002 LED does not blink.

Clone menu hard to read.

No time set.

Clone not working.

Wrong Installer Remote.

MPI cord not connected. TV not turned ON.

(LT2002 only) Weak batteries. (TLL-1100A only) No charge.

Weak signal.

Time not available.

Clone programmer problem.

Only use an LG Installer Remote to operate clone programmer with TV.

Connect MPI cord properly, and ensure good connection. TV must be powered ON for clone programmer to work. Install four (4) fresh AA high-quality alkaline batteries.

Ensure the TLL-1100A is fully charged or connected to AC power.

Connect TV to a reliable analog channel signal source.

Set time on a TV, and copy time to clone programmer.

???Try a different clone programmer.

???Reset the clone programmer.

75 OHM RF CABLE

The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV.

300 TO 75 OHM ADAPTER

A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack. It is usually about an inch long with two screws on one end and a round opening with a wire extending out the other end.

A/V CABLES

Audio/Video cables. Three cables bunched together???right audio (red), left audio (white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality pic- ture and sound from other A/V devices.

A/V DEVICE

Any device that produces video or sound (VCR, DVD, cable box, or television).

AMPLIFIER

An electronic device that ampli???es sound from a television, CD player, VCR, DVD player, or other Audio/Video device.

ANTENNA

The physical receiver of television sig- nals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

b-LAN

Licensed proprietary RF communication system used to con???gure/control TV via RF distribution system.

CABLE

Cable service box. Refers to the de- scrambler box cable subscribers use to receive cable programming signals.

CATV

Programming provided by a cable service.

COMPONENT VIDEO

Uses three wires for transporting three- color video signals. The end result is usually better video quality.

COMPOSITE VIDEO

Typical video jack, uses one wire for transporting three-color video signals.

DELETE

Lets you remove channels from the list that the end user can scroll through us- ing Channel Up/Down.

DIGITAL TELEVISION

High-resolution, cinema-quality television signals transmitted digitally.

DVI

Digital Video Interface. Accommodates analog and digital interfaces with a single connector.

HDMI

High-de???nition multi-media interface.

HDSTB

High-de???nition set top box. Refers to a tuner device that receives high-de???nition television signals which have higher res- olution than ordinary analog TV signals.

HDTV

High-de???nition television. Refers to tele- vision signals that have higher resolu- tion than ordinary analog TV signals.

INPUT

Refers to the input jack that receives a signal from a TV, VCR, DVD Player or other Audio/Video device.

JACK

An input or output connector on the back of a TV, VCR, DVD Player or other Audio/Video device.

MONO SOUND

Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

OUTPUT

Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device.

PHYSICAL CHANNEL NUMBER

The actual channel number. Analog channels use the Physical Channel number and digital channels can use a Virtual Channel number.

RGB (RED, GREEN, BLUE)

Connection input or output port avail- able for producing a video image using three separate colors: Red, Green, and Blue.

RS-232

Serial communication port through which ???rmware is downloaded.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another, separate audio channel avail- able with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French.

SIGNAL

Picture and sound traveling through a cable, or over the air, to the TV.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio that???s divided into right and left sides.

TUNER

Device that picks up the broadcast sig- nal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

A re-mapped channel number. Analog channels use the Physical Channel number; however digital channels use a Virtual (or false) Channel number.

XDS

Extended Data Service. Additional program information included on the signal provided at the discretion of the broadcaster.

Note: Refer to www.atsc.org for further information.