IBM_Computer_Drive

Safety

Before installing this product, read the Safety Information.

Antes de instalar este produto, leia as Informa????es de Seguran??a.

Pred instalac?? tohoto produktu si prectete pr??rucku bezpecnostn??ch instrukc??.

L??s sikkerhedsforskrifterne, f??r du installerer dette produkt.

Ennen kuin asennat t??m??n tuotteen, lue turvaohjeet kohdasta Safety Information. Avant d???installer ce produit, lisez les consignes de s??curit??.

Vor der Installation dieses Produkts die Sicherheitshinweise lesen.

Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.

Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.

Les sikkerhetsinformasjonen (Safety Information) f??r du installerer dette produktet.

Antes de instalar este produto, leia as Informa????es sobre Seguran??a.

Antes de instalar este producto lea la informaci??n de seguridad.

General safety guidelines

Always observe the following precautions to reduce the risk of injury and property damage.

Service

Do not attempt to service a product yourself unless instructed to do so by the IBM Support Center. Use only an IBM authorized service provider who is approved to repair your particular product.

Note: Some parts can be upgraded or replaced by the customer. These parts are referred to as Customer Replaceable Units, or CRUs. IBM expressly identifies CRUs as such, and provides documentation with instructions when it is appropriate for customers to replace those parts. You must closely follow all instructions when performing such replacements. Always make sure that the power is turned off and that the product is unplugged from any power source before you attempt the replacement. If you have any questions or concerns, contact the IBM Support Center.

Power cords and power adapters

Use only the power cords and power adapters supplied by the product manufacturer.

Never wrap a power cord around the power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack or crimp. This can present a safety hazard.

Always route power cords so that they will not be walked on, tripped over, or pinched by objects.

Protect the cord and power adapters from liquids. For instance, do not leave your cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short circuit, particularly if the cord or power adapter has been stressed by misuse. Liquids can also cause gradual corrosion of the power cord terminals and/or the connector terminals on the adapter which can eventually result in overheating.

Always connect power cords and signal cables in the correct order and ensure that all power cord connectors are securely and completely plugged into receptacles.

Do not use any power adapter that shows corrosion at the ac input pins and/or shows signs of overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.

Do not use any power cords where the electrical contacts on either end show signs of corrosion or overheating or where the power cord appears to have been damaged in any way.

Extension cords and related devices

Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.

Plugs and outlets

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if you have questions about power loads and branch circuit ratings.

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.

Connect and disconnect the equipment from the electrical outlet carefully

Batteries

All IBM personal computers contain a non-rechargeable coin cell battery to provide power to the system clock. In addition many mobile products such as Thinkpad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by IBM for use with your product have been tested for compatibility and should only be replaced with IBM approved parts.

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to ???vent??? from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could

viii IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state.

Heat and product ventilation

Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size. Always follow these basic precautions:

vDo not leave the base of your computer in contact with your lap or any part of your body for an extended period when the computer is functioning or when the battery is charging. Your computer produces some heat during normal operation. Extended contact with the body could cause discomfort or, potentially, a skin burn.

vDo not operate your computer or charge the battery near flammable materials or in explosive environments.

vVentilation slots, fans and/or heat sinks are provided with the product for safety, comfort, and reliable operation. These features might inadvertently become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover or disable these features.

CD and DVD drive safety

CD and DVD drives spin discs at a high speed. If a CD or DVD is cracked or otherwise physically damaged, it is possible for the disc to break apart or even shatter when the CD drive is in use. To protect against possible injury due to this situation, and to reduce the risk of damage to your machine, do the following:

vAlways store CD/DVD discs in their original packaging

vAlways store CD/DVD discs out of direct sunlight and away from direct heat sources

vRemove CD/DVD discs from the computer when not in use

vDo not bend or flex CD/DVD discs, or force them into the computer or their packaging

vCheck CD/DVD discs for cracks before each use. Do not use cracked or damaged discs

About this book

This manual contains instructions for installing the IBM?? USB 2.0

CD-RW/DVD-ROM Drive hardware.

This manual provides installation instructions in the following languages:

vBrazilian Portuguese

vCzech

vEnglish

vFrench

vGerman

vItalian

vJapanese

vSimplified Chinese

vSlovak

vSpanish

vTraditional Chinese

vTurkish

Registering your option

Thank you for purchasing this IBM product. Please take a few moments to register your product and provide us with information that will help IBM to better serve you in the future. Your feedback is valuable to us in developing products and services that are important to you, as well as in developing better ways to communicate with you. Register your option on the IBM Web site at:

http://www.ibm.com/pc/register/

IBM will send you information and updates on your registered product unless you indicate on the Web site questionnaire that you do not want to receive further information.

Chapter 1. Combo Drive quick install

This chapter contains instructions for installing the IBM USB 2.0

CD-RW/DVD-ROM Drive, (hereafter the drive will be referred to as Combo

Drive).

Product description

The IBM USB 2.0 CD-RW/DVD-ROM Drive is a slimline DVD-ROM and CD recordable drive that attaches quickly and conveniently to your IBM ThinkPad?? computer through a simple connection. The drive is a USB 2.0 device and requires connection to one or two USB 2.0 ports. A maximum write speed of 8x (CD-R/CD-RW media) can be obtained. Maximum read speeds of 6x (DVD media) and 20x (CD media) can be obtained.

In addition to this manual, the option package includes: v IBM USB 2.0 CD-RW/DVD-ROM Drive

vStandard USB cable assembly (P/N 73P4522 is to be used for ???Read Only??? operations.)

vUSB 2.0 ???Y??? cable assembly (P/N 73P4517 is to be used for ???Read/ Write??? operations).

vIBM USB 2.0 CD-RW/DVD-ROM Drive Software and Guide Super CD

vSafety information manual

Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of purchase and packing material. They might be required to receive warranty service.

Hardware and software requirements

You must have the following hardware installed on your ThinkPad computer in order to use this option:

v One or two USB 2.0 ports; Two are required for ???write??? operations.

Your computer must have one of the following operating systems installed to use this option:

vMicrosoft?? Windows?? XP

vMicrosoft Windows 2000 Professional (Service Pack 4 or later)

Note: The drive will not operate correctly unless Service Pack 4 or later is installed.

Identifying the combo drive components

The following diagrams provide information on the combo drive components, including the controls and connectors. The diagrams below display the top panel, bottom panel, disc open, and using the disc for the first time illustrations.

v1Disc cover

v2Power/Busy indicator

vGreen: Drive???s power is on.

vSlowly blinking amber: Data is being read.

vQuickly blinking amber: Media is being recognized.

v3Write indicator

vAmber: Data is being written.

v4 Power switch [POWER]

v5 Open button [OPEN]

1-2 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

v6 Turntable

v7Lens

v 8Lens protective sheet

v9USB Interface connector

v10Emergency eject lever

Operating Configurations

This section provides operating configurations for the Combo Drive .

1)For ???Read Only??? operations, use cable P/N 73P4522. Connect the drive to one standard USB 2.0 port on the system.

2)For ???Read/Write??? operations, use USB ???Y??? cable P/N 73P4517. Connect the drive to two standard USB 2.0 ports on the system.

Chapter 1. Combo Drive quick install 1-3

Chapter 3. Features

The following list contains features of the IBM USB 2.0 CD-RW/DVD-ROM Drive:

vEasy connection

Since this product incorporates the interface conforming to the USB 2.0 High Speed, it can be connected or disconnected to or from your computer easily even when the power of the computer is on. IBM Docks and Port Replicators with AC power are supported.

vConformance to media manufactured by major media manufacturers

This product is best tuned to almost all the CD and DVD media manufactured by major media manufacturers and the media written by this product realizes a very high write quality. Therefore, this drive can be used with little concern for compatibility issues.

vIncorporation of the buffer underrun prevention function

This product incorporates the buffer underrun prevention function which helps to prevent buffer underrun errors that cause a write failure onto the CD.

vTop loading

This product has a top loading mechanism that allows easy loading and ejection of a disc. The top cover can be opened manually or by using software that works with the computer.

vConformance to multiple standards

This drive conforms with industry standard specifications for CD-RW and CD-R media. This drive is compliant with DVD+RW, DVD+R, DVD-RAM, DVD-RW, and DVD-R specifications (read only).

vNo power adapter configuration

This drive Reads and/or Writes with the USB 2.0 port connections only.

This user???s manual on the CD included with this option describes how to set up the Combo Drive, how to connect it to a personal computer, and how to operate it. Read the instruction manual of your computer as well.

The CD also includes software applications for use with the Combo Drive. They will automatically install by clicking on them.

Read this instruction manual carefully before use for proper handling and operations of the Combo Drive.

Chapter 4. Preparing to use the Combo Drive

Before using the Combo Drive, follow the procedure below:

1.Make sure the Combo Drive is properly connected to your ThinkPad computer.

2.Check the locations of the functions on the Combo Drive (refer to the figures below).

3.Insert the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD that was shipped with this option to install the CD-R/CD-RW writing software or DVD read software.

4.Double-click on the application you want and follow the instructions on the screen.

5.Check that the drive operates normally and keep the enclosed warranty in a safe place after filling it in.

Check that nothing is placed on the top cover when ejecting a CD or DVD. When normal ejection is impossible, an error message may appear on your computer. When ejection is not performed normally, open the top cover manually and close it securely after removing anything that may be on the cover.

Following are the locations of the functions on the Combo Drive:

Chapter 5. Combo Drive hardware installation and removal in Windows 2000 and Windows XP

Windows 2000 and Windows XP operating systems have the native drivers for the Combo Drive. Therefore, when this drive is connected, Windows will automatically install the appropriate driver and the drive will be ready to be used. You do not have to perform any special installation or removal procedures.

Attention:

vThis drive will be recognized as ???IBM CDRW/DVD UJDB753 USB Device??? by Windows Device Manager.

vIn Windows 2000 operating systems, Service Pack 4 or later must be installed.

Removing the Combo Drive hardware

???Hot plug??? is supported for the connection between the USB cable and the computer; therefore you don???t need to turn off the computer when you remove the Combo Drive. Follow the procedure below for removing the Combo Drive for Windows 2000 and Windows XP.

Attention:

Do not remove and reconnect the drive from or to the computer in rapid succession. The drive may not be recognized. Reconnect the drive approximately 20 seconds after removing.

Use the Tray icon for this procedure.

Windows 2000

1.Exit the program that uses the drive.

2.Confirm that the Write indicator of the drive is off.

3.Click the Remove icon on the tray.

4.Select removing drive. In this case, select the drive name assigned to the drive (D: in this figure).

5.The Safe to Remove Hardware confirmation window appears. Click the OK button.

6. Remove the plug of the USB cable from the USB terminal of the computer.

Note: The message indicated above may differ depending on the versions of your operating system. Refer to the instruction manual for your computer or operating system for details.

Windows XP

1.Exit the program that uses the drive.

2.Confirm that the Write indicator of the drive is off.

3.Click the Remove icon on the tray.

4.Select removing drive. In this case, select the drive name assigned to the drive (D: in this figure).

5.The Safe to Remove Hardware confirmation window appears. Click the OK button.

6. Remove the plug of the USB cable from the USB terminal of the computer.

Note: The message indicated above may differ depending on the versions of your operating system. Refer to the instruction manual for your computer or operating system for details.

Setting the media

1.Press the eject button of the drive to open the top cover.

2.Place the media on the tray with the label face upward. Align the center hole of the disc with the clamp at the center of the tray and fit the disc in securely by pressing the outer vicinity of the center hole.

3.Close the top cover gently and press the cover down until it is completely locked.

4.When the top cover is correctly closed, the media is recognized and made usable after the busy indicator blinks for some seconds.

Ejecting the media

1.Press the eject button of the drive to automatically open the top cover.

2.Lift the edge of the disc carefully from the tray while pressing the upper section of the clamp.

3.Close the top cover gently until the cover is completely closed. Check that the cover is securely locked.

5-2 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

Playing back the audio CD

Use Windows Media Player or audio CD playback software such as Microsoft CD Player for playing back the audio CD using the drive. The operation method differs depending on the software and versions. Refer to the operation manual of your computer or software for details.

Windows 2000

In Windows Media Player, you will find Digital Playback check box when you click the CD Audio tab in the Options window, as shown in the following figure.

In addition, you will find the Enable Digital Music CD with this Combo Drive check box on the Combo Drive property on Device Manager, as shown in the figure below. When there is no setting item for the digital playback in your player

Chapter 5. Combo Drive hardware installation and removal in Windows 2000 and Windows XP 5-3

Chapter 6. Application software

Your IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD contains the following software:

vIBM Drive Letter Access (DLA)

This software enables you to write directly to CD-RW media only using the drive letter like you would if you were writing to a diskette. All disc format types can be formatted by DLA. With DLA, you can drag-and-drop files, create new directories, or save files from any application directly to your Combo Drive.

vUDF reader

This software enables you to install software for reading DVD-RAM, DVD-RW, and CD-RW media on computers with DVD drives. It also allows you to read DLA-created discs on systems without DLA installed.

vIBM RecordNow

IBM RecordNow is disc mastering software that allows you to create your own music or data discs from files on your computer, or from other disc media such as CDs or DVDs. Music discs created with IBM RecordNow will play on any CD player, whether it???s at home, in your car, or through your computer???s CD-ROM. IBM RecordNow also makes it easy to create data discs that can be read on any appropriate CD or DVD disc reader.

Note: Some DVD players cannot read CD-R media. Refer to the documentation that accompanied your drive for information on supported media.

IBM RecordNow guides you, step-by-step, through the recording process with simple Wizards and an intuitive user-interface.

Using IBM RecordNow you can create:

???Exact copies of existing discs - The Exact Copy feature makes a duplicate of your master disc, transferring the disc layout of the original disc to your CD-R or CD-RW.

???Discs of archived data from your hard drive ??? The Make a Data Disc feature is used to store electronic data, such as the files and applications that reside on your computer???s hard drive. Unlike music discs, data discs are used to store files that are readable only by a computer, and cannot be played on your home or car stereo???even if audio files are on the disc.

???Music compilations from WAV, MP3, or WMA files, or from existing music discs ??? The Make a Music Disc feature creates custom music discs from files on your hard drive or your existing music discs. The CD music database feature can automatically tag your files with track information to help you sort through your collection.

Note: Please reference the IBM RecordNow On-line Help, for more information on how to Make an Exact copy, Create a Data Disc, or to Create an Audio disc with IBM RecordNow.

To start RecordNow, complete the following procedure:

1.Click Start.

2.Click Programs.

3.Click IBM RecordNow.

4.Click RecordNow to open the main recording software window.

Chapter 7. Using the Combo Drive

This section provides information on how to handle, load, and care for DVDs and CDs and how to care for your Combo Drive.

Before you begin

For best results, review the following guidelines before using the drive:

vDo not move your ThinkPad computer while formatting or writing a disc as this might cause data errors. Also, minimize typing while formatting or writing to a disc, as this might also cause data errors.

vKeep the ThinkPad computer on a flat surface when writing to a disc.

vTurn screensavers off. Using a screensaver might interrupt the formatting and writing process.

vDo not put your ThinkPad computer into hibernation or suspend mode while writing to a disc.

Note: The read and write results of the drive depend upon the quality and characteristics of the DVD or CD media used.

Handling and caring for a disc

Carefully handle and clean discs, especially writable media types such as CD-R and CD-RW discs, so that they remain readable. You can prolong the life of your discs by using the following precautions:

vAlways store discs in their original packaging.

vAlways store discs out of direct sunlight.

vAlways store discs away from direct heat sources.

vRemove discs from the computer when not in use.

vCheck discs for cracks BEFORE each use.

IMPORTANT: Do not use discs that are cracked.

vDo not force discs into the computer or packaging.

vDo not bend or flex discs.

vDo not use commercial cleaners to clean discs.

vDo not write on the surface of discs.

vHandle discs by the edges or the center hole.

vDo not touch the surface of discs.

vTo remove dust or fingerprints, wipe discs from the center to the edge with a soft, lint-free cloth.

Attention: Wiping a disc using a circular motion can cause data loss.

Caring for the Combo Drive

To protect your drive during operation, observe the following precautions:

vRemove the disc from the drive before moving the drive.

vDo not insert foreign objects into the drive.

vDo not stack objects on the drive.

vDo not remove the drive cover or attempt to service the drive.

vDo not operate the drive under any of the following conditions:

???High temperature, high humidity, or direct sunlight

???Excessive vibration, sudden shock, or inclined surface

???Excessive dust

Cleaning the drive

Wipe off soil on the drive using a soft cloth. If soil is persistent, use a cloth dampened with a diluted neutral detergent after squeezing all the water out. If liquid is allowed into the drive, it may cause a serious malfunction, an electric shock or a fire.

Do not apply solvents such as benzene or thinner. Chemical cleaners for home or industrial use may damage the coating of the drive.

Using the drive

This section contains information on using the Combo Drive.

Using single and double-sided DVD-RAM media

DVD-RAM media is available in single-sided and double-sided versions.

The 2.6 GB and 4.7 GB versions are single-sided. The 9.4 GB version is double-sided. To access the data on both sides of the media, you must remove the media from the drive, turn it over, and re-insert it into the drive.

Precautions for handling

Be careful when handling the removed disc. Debris, dust particles, fingerprints, smears, or scratches may impair recording and playback of the media. To clean dust or other debris, use a CD Cleaning Kit. Use a soft, dry cloth to clean the disc.

7-2 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

Using the drive with CDs and DVDs

Complete the following procedure to read a data disc:

1.Turn on the computer.

2.Press the Eject button on the top of the drive.

3.Insert a disc in the tray with the label facing up.

4.Close the drive by gently closing the top cover.

5.Wait for the drive busy indicator to stop blinking and turn off.

6.Double-click the CD-ROM or DVD-RAM/DVD-R/DVD-RW icon.

Using the DVD player software

This section describes how to use and customize the DVD Player software. You can find current information on DVD Player software in the readme file on the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD.

Using the DVD function

To use the DVD function, you need to install WinDVD (the DVD movie player program).

Enabling driver letter access (DLA)

Drive Letter Access (DLA) is provided so that you can write data to CD-RW media. CD-RW media can be written to many times.

To format and write to CD-RW media:

1.Insert a disc into the drive.

2.Double-click My Computer. Right-click the drive letter for the USB 2.0 Combo Drive.

3.Click Format. Formatting time will vary depending on the format process you use (quick or full).

4.After formatting is complete, you can drag and drop files to the USB 2.0 Combo Drive icon, or you can move files in Windows Explorer.

To use UDF formatted CD-RW media in other computers, a UDF reader is included on the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD. To use the UDF reader, follow this procedure:

1.Insert the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD into the CD or DVD drive of the computer you want to use the UDF formatted discs with.

2.Click Start.

3.Click Run.

4.Type e:\UDFREADR\language where e is the drive letter of the USB 2.0 Combo Drive, and language is your language.

5.Click OK.

6.Double-click SETUP.EXE and follow the on-screen instructions.

Note: The UDF reader is only needed on systems that do not have another DLA program for CD-RW installed.

7-4 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

Installing WinDVD and viewing a DVD movie

To install WinDVD, go to the ???Software??? section of the IBM USB 2.0

CD-RW/DVD-ROM Drive Software and User???s Guide Super CD.

After you install the Combo Drive and WinDVD software, you can view a DVD movie. But first you need to set the DVD region code for your DVD content.

DVD region codes

DVD region codes help protect the contents of a DVD. The world is divided into six regions and specific content can be viewed only in the appropriate region. For example, content for Region 1 can be viewed only in the U.S. and Canada.

WinDVD is also region???specific.

You can verify the region code of the content by looking at the region code symbol on the back of the content packaging.

Start WinDVD by inserting the DVD into the drive. The region code is automatically set and you can view the movie. This is the initial setting.

After the region code has been set, if you insert a DVD with a different region code, you are prompted to change the region code. You can change the region code from your initial setting up to four times.

After the region code has been changed from its initial setting four times, it is fixed and can no longer be changed. Thereafter, you can play DVD content only from that region.

To display the region code status, click the WinDVD Properties button on the

WinDVD user interface. The General tab contains this information.

To change the region code, do the following:

1.Turn on your computer and start your operating system.

2.Click Start.

3.Select Programs.

4.Click Intervideo WinDVD.

5.Click the Properties icon to open the Properties window.

6.Click the General Properties tab.

7.Insert a single region DVD of the new region.

8.Select the correct region code for your country.

9.Click OK.

Chapter 7. Using the Combo Drive 7-5

Starting WinDVD

To start WinDVD, complete the following procedure:

1.Click Start.

2.Click Programs.

3.Click InterVideo WinDVD.

4.Click InterVideo WinDVD to open the DVD movie player window.

For more information on how to play the DVD movie player, refer to the WinDVD help information on the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD. If you want to watch a DVD movie on your TV, refer to the online information provided with your computer.

Notes:

1.Your computer has been configured to provide the highest quality audio and video playback obtainable with the available system resources. You can alter the default settings by changing the video resolution setting within the Control Panel. Some systems do not have enough resources to provide full-quality audio and video playback at all resolution settings. If you experience poor playback performance, adjust the resolution to a lower setting.

2.Audio or video streams are decoded by software. The audio and video subsystems need to be fully functional and enabled.

Using the CD-R and CD-RW function

The Combo Drive can write to both CD-R and CD-RW discs. CD-R discs cannot be erased, but can be used with standard CD-ROM drives and CD players.

You can use CD-R discs to record audio tracks, store data, archive files, and copy files from another CD.

CD-RW discs can be erased and rewritten, but can be used only with newer MR- and CD-RW-compatible CD-ROM and DVD-ROM drives. You can use CD-RW discs to back up, store, and update files or to copy files from another CD.

Notes:

1.CD-R discs are playable on audio CD players. CD-RW discs are not playable on most audio CD players.

2.The software included with this drive does not enable the drive CD-recording capabilities with DOS, Windows 3.x, or IBM OS/2?? operating systems.

For more information on using the software, refer to the IBM RecordNow and IBM DLA help information on the IBM USB 2.0 CD-RW/DVD-ROM Drive Software and User???s Guide Super CD.

Using the DVD+R, DVD+RW, DVD-R, DVD-RW, and DVD-RAM function (read only)

The Combo Drive can read DVD+R, DVD+RW, DVD-R, DVD-RW, and DVD-RAM discs.

7-6 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

Backing up a CD

To copy a commercial CD you must own the copyright or obtain permission from the copyright owner. If you do not own the copyright or do not obtain permission from the copyright owner, you might be violating copyright law and might be subject to payment of damages or other remedies. For more information on copyright law, consult your legal advisor.

Problem solving

Computer problems can be caused by hardware, software, or user error. The information in this section might be useful to help you solve problems or to gather helpful information you can pass on to a service technician. You might also need to refer to your computer, operating-system, or sound-adapter publications.

Review the following list for any problem descriptions that might fit your situation.

You cannot create a multi session disc.

Be sure that there is enough space left on the disc for another session. Writing a session requires lead-in and lead-out space (about 15 MB) in addition to the data that is recorded.

You cannot successfully write to a CD-R or CD-RW disc.

Take the following actions:

1.Verify that the process is not being interrupted by a screen saver, an antivirus program, an Internet or e-mail program, or other software. Disable the functions that might interrupt the write operation.

2.Verify that the hard disk has been defragmented.

3.Consult the hard disk drive manufacturer or vendor if an older hard disk drive is conducting a thermal recalibration during a write operation.

4.Replace the disc if it is bad or scratched.

5.Disable the Windows Auto Insert Notify function on your CD-ROM and CD-RW drives.

You cannot eject a disc.

Take the following actions after ensuring that the drive is not in the process of writing to a disc:

1.Eject the disc through software.

2.Use the Eject button.

3.Turn off the computer. Wait 45 seconds; then turn on the computer and try using the Eject button again.

4.If other methods do not work, use the emergency eject lever. For more information, see Chapter 4, ???Preparing to use the Combo Drive,??? on page 4-1.

You cannot read from the CD disc after successfully writing to it.

Take the following actions:

Chapter 7. Using the Combo Drive 7-7

Appendix A. Product specifications

This appendix includes the following information:

vPhysical specifications

vPower requirements

vEnvironmental requirements

vRead speeds

vWrite speeds

Physical specifications:

The physical specifications1 of the drive are listed in the following table.

Power requirements:

The following table lists the power specifications by voltage level for the drive. The power specifications are measured at the drive power connector and are nominal values.

Environmental requirements:

1.Product-description data represents IBM???s design objectives and is provided for comparative purposes; actual results might vary based on a variety of factors. This product data does not constitute a warranty. Data is subject to change without notice.

Appendix B. Service and Support

The following information describes the technical support that is available for your product, during the warranty period or throughout the life of the product. Refer to your IBM Statement of Limited Warranty for a full explanation of IBM warranty terms.

Online technical support

Online technical support is available during the life of your product through the Personal Computing Support Web site at http://www.ibm.com/pc/support.

During the warranty period, assistance for replacement or exchange of defective components is available. In addition, if your IBM option is installed in an IBM computer, you might be entitled to service at your location. Your technical support representative can help you determine the best alternative.

Telephone technical support

Installation and configuration support through the IBM Support Center will be withdrawn or made available for a fee, at IBM???s discretion, 90 days after the option has been withdrawn from marketing. Additional support offerings, including step-by-step installation assistance, are available for a nominal fee.

To assist the technical support representative, have available as much of the following information as possible:

vOption name

vOption number

vProof of purchase

vComputer manufacturer, model, serial number (if IBM), and manual

vExact wording of the error message (if any)

vDescription of the problem

vHardware and software configuration information for your system

If possible, be at your computer. Your technical support representative might want to walk you through the problem during the call.

For the support telephone number and support hours by country, refer to the following table. If the number for your country or region is not listed, contact your IBM reseller or IBM marketing representative. Response time may vary depending on the number and nature of the calls received.

Phone numbers are subject to change without notice. For the latest phone number list, go to http://www.ibm.com/pc/support and click Support Phone List.

Appendix C. IBM Statement of Limited Warranty Z125-4753-08 04/2004

Part 1 - General Terms

This Statement of Limited Warranty includes Part 1 - General Terms, Part 2 - Country-unique Terms, and Part 3 - Warranty Information. The terms of Part 2 replace or modify those of Part 1. The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you purchase for your use, and not for resale. The term ???Machine??? means an IBM machine, its features, conversions, upgrades, elements, or accessories, or any combination of them. The term ???Machine??? does not include any software programs, whether pre-loaded with the Machine, installed subsequently or otherwise.

Nothing in this Statement of Limited Warranty affects any statutory rights of consumers that cannot be waived or limited by contract.

What this Warranty Covers

IBM warrants that each Machine 1) is free from defects in materials and workmanship and 2) conforms to IBM???s Official Published Specifications (???Specifications???) which are available on request. The warranty period for the Machine starts on the original Date of Installation and is specified in Part 3 - Warranty Information. The date on your invoice or sales receipt is the Date of Installation unless IBM or your reseller informs you otherwise. Many features, conversions, or upgrades involve the removal of parts and their return to IBM. A part that replaces a removed part will assume the warranty service status of the removed part. Unless IBM specifies otherwise, these warranties apply only in the country or region in which you purchased the Machine.

THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE

ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR

CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE

EXCLUSION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH

WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY PERIOD.

NO WARRANTIES APPLY AFTER THAT PERIOD. SOME STATES OR

JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

What this Warranty Does not Cover

This warranty does not cover the following:

vany software programs, whether pre-loaded or shipped with the Machine, or installed subsequently;

vfailure resulting from misuse (including but not limited to use of any Machine capacity or capability, other than that authorized by IBM in writing), accident, modification, unsuitable physical or operating environment, or improper maintenance by you;

vfailure caused by a product for which IBM is not responsible; and

vany non-IBM products, including those that IBM may procure and provide with or integrate into an IBM Machine at your request.

The warranty is voided by removal or alteration of identification labels on the

Machine or its parts.

IBM does not warrant uninterrupted or error-free operation of a Machine.

Any technical or other support provided for a Machine under warranty, such as assistance with "how-to" questions and those regarding Machine set-up and installation, is provided WITHOUT WARRANTIES OF ANY KIND.

How to Obtain Warranty Service

If the Machine does not function as warranted during the warranty period, contact IBM or your reseller to obtain warranty service. If you do not register the Machine with IBM, you may be required to present proof of purchase as evidence of your entitlement to warranty service.

What IBM Will Do to Correct Problems

When you contact IBM for service, you must follow the problem determination and resolution procedures that IBM specifies. An initial diagnosis of your problem can be made either by a technician over the telephone or electronically by access to an IBM website.

The type of warranty service applicable to your Machine is specified in Part 3 - Warranty Information.

You are responsible for downloading and installing designated Machine Code (microcode, basic input/output system code (called ???BIOS???), utility programs, device drivers, and diagnostics delivered with an IBM Machine ) and other software updates from an IBM Internet Web site or from other electronic media, and following the instructions that IBM provides.

If your problem can be resolved with a Customer Replaceable Unit (???CRU???) (e.g., keyboard, mouse, speaker, memory, hard disk drive), IBM will ship the CRU to you for you to install.

If the Machine does not function as warranted during the warranty period and your problem cannot be resolved over the telephone or electronically, through your application of Machine Code or software updates, or with a CRU, IBM or your reseller, if approved by IBM to provide warranty service, will either, at its discretion, 1) repair it to make it function as warranted, or 2) replace it with one that is at least functionally equivalent. If IBM is unable to do either, you may return the Machine to your place of purchase and your money will be refunded.

IBM or your reseller will also manage and install selected engineering changes that apply to the Machine.

Exchange of a Machine or Part

When the warranty service involves the exchange of a Machine or part, the item IBM or your reseller replaces becomes its property and the replacement becomes yours. You represent that all removed items are genuine and unaltered. The replacement may not be new, but will be in good working order and at least functionally equivalent to the item replaced. The replacement assumes the warranty service status of the replaced item.

Your Additional Responsibilities

Before IBM or your reseller exchanges a Machine or part, you agree to remove all features, parts, options, alterations, and attachments not under warranty service.

You also agree to:

C-2 IBM USB 2.0 CD-RW/DVD-ROM Drive: User???s Guide

1.ensure that the Machine is free of any legal obligations or restrictions that prevent its exchange;

2.obtain authorization from the owner to have IBM or your reseller service a Machine that you do not own; and

3.where applicable, before service is provided:

a.follow the service request procedures that IBM or your reseller provides;

b.backup or secure all programs, data, and funds contained in the Machine;

c.provide IBM or your reseller with sufficient, free, and safe access to your facilities to permit IBM to fulfill its obligations; and

d.inform IBM or your reseller of changes in the Machine???s location.

4.(a) ensure all information about identified or identifiable individuals (Personal Data) is deleted from the Machine (to the extent technically possible), (b) allow IBM, your reseller or an IBM supplier to process on your behalf any remaining Personal Data as IBM or your reseller considers necessary to fulfill its obligations under this Statement of Limited Warranty (which may include shipping the Machine for such processing to other IBM service locations around the world), and (c) ensure that such processing complies with any laws applicable to such Personal Data.

Limitation of Liability

IBM is responsible for loss of, or damage to, your Machine only while it is 1) in IBM???s possession or 2) in transit in those cases where IBM is responsible for the transportation charges.

Neither IBM nor your reseller are responsible for any of your confidential, proprietary or personal information contained in a Machine which you return to IBM for any reason. You should remove all such information from the Machine prior to its return.

Circumstances may arise where, because of a default on IBM???s part or other liability, you are entitled to recover damages from IBM. In each such instance, regardless of the basis on which you are entitled to claim damages from IBM (including fundamental breach, negligence, misrepresentation, or other contract or tort claim), except for any liability that cannot be waived or limited by applicable laws, IBM is liable for no more than

1.damages for bodily injury (including death) and damage to real property and tangible personal property; and

2.the amount of any other actual direct damages, up to the charges (if recurring, 12 months??? charges apply) for the Machine that is subject of the claim. For purposes of this item, the term ???Machine??? includes Machine Code and Licensed Internal Code (???LIC???).

This limit also applies to IBM???s suppliers and your reseller. It is the maximum for which IBM, its suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS

LIABLE FOR ANY OF THE FOLLOWING EVEN IF INFORMED OF THEIR

POSSIBILITY: 1) THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES

(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS

OF, OR DAMAGE TO, DATA; 3) SPECIAL, INCIDENTAL, OR INDIRECT

DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; OR 4)

LOST PROFITS, BUSINESS REVENUE, GOODWILL OR ANTICIPATED

SAVINGS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU. SOME STATES OR JURISDICTIONS DO NOT ALLOW

Appendix C. IBM Statement of Limited Warranty Z125-4753-08 04/2004 C-3

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE

ABOVE LIMITATION MAY NOT APPLY TO YOU.

Governing Law

Both you and IBM consent to the application of the laws of the country in which you acquired the Machine to govern, interpret, and enforce all of your and IBM???s rights, duties, and obligations arising from, or relating in any manner to, the subject matter of this Statement of Limited Warranty, without regard to conflict of law principles.

THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY

ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR

JURISDICTION TO JURISDICTION.

Jurisdiction

All of our rights, duties, and obligations are subject to the courts of the country in which you acquired the Machine.

Part 2 - Country-unique Terms

AMERICAS

ARGENTINA