08160

TH106

TL6160

Temperature preset buttons

NOTE: Always keep the thermostat's vents clean and unobstructed.

n

Program the schedule

Skip a period

Select the mode of operation

Indicates the heating power

Temperature adjustment buttons

Temperature preset icon

Indicates that the thermostat is configured for a fan-forced heater

Indicates the current period (appears in automatic mode only)

Indicates that the ther- mostat is without power *

oConnect the thermostat wires to the line wires and to the load wires using solderless connectors for copper wires.

* LP appears only for the first two minutes when the thermostat is without power. This can occur during a power outage or when the thermal protection device inside the base- board heater is opened.

n Description

This programmable thermostat can be used to control an electric heating system such as an electric baseboard heater, a radiant ceil- ing, a radiant floor, a convector or a fan-forced heater.

The thermostat cannot be used with:

???a resistive load over 16.7 A

???a resistive load under 2 A

???a system driven by a contactor or relay (inductive load)

???a central heating system

SUPPLIED PARTS:

???One (1) thermostat

???Two (2) 6-32 screws

???Two (2) solderless connectors

o Installation

TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN

POWER PANEL TO AVOID ELECTRICAL SHOCK. THE INSTAL-

LATION MUST BE PERFORMED BY AN ELECTRICIAN.

All cables and connections must conform to the local electrical code.

Special CO/ALR solderless connectors must be used when con- necting with aluminum conductors.

Install the thermostat onto an electrical box.

Install the thermostat about 5 feet high, on an inside wall facing the heater.

Avoid locations where there are air drafts (such as the top of a staircase or an air outlet), dead air spots (such as behind a door), or direct sunlight.

Do not install the thermostat on a wall that conceals chimney or stove pipes.

The thermostat wires are not polarized; either wire can be con- nected to the load or to the power supply.

2-wire installation

4-wire installation

p Push any excess wire back into the electrical box.

NOTE: If necessary, before re-installing the front component, config- ure the thermostat (see section 3).

q Return power to heating system.

p Configuration

The configuration switches are on the back of the thermostat. The factory settings are indi- cated by the gray cells in the following table.

a.Early Start can be used in Automatic mode only. When this func- tion is enabled, the thermostat calculates the optimal time to start heating in order to obtain the desired temperature by the set time. The thermostat re-assesses the start time daily based on the pre- vious day???s performance.

b.You must select 5 minutes if you have a fan-forced heater. The word FAN is displayed when this setting is selected. Select

15 seconds for better temperature control in most other cases.

c.The settings are locked. The temperature adjustment buttons only allow you to view the temperature setpoint.

q Clock and Day Setting

n Press the Hour button to set the hour. o Press the Min button to set the minutes. p Press the Day button to set the day.

q Press the Mode button to end.

Daylight Savings Time

The thermostat can automatically re-adjust its clock at Daylight Sav- ings Time changeover. When this function is enabled (On), the ther- mostat switches to Daylight Savings Time on the second Sunday of March and to normal time on the first Sunday of November.

NOTE: The function is disabled (default setting) when the clock loses its setting.

n Press the Day button (3 seconds) until DLS appears on the screen.

oPress either of the buttons to toggle between On (enabled) and Off (disabled).

p Press the Day button briefly. The year setting is dis- played.

q Press either of the buttons to set the current year.

r Press the Day button briefly. The month setting is dis- played.

s Press either of the buttons to set the current month.

t Press the Day button briefly. The date setting is dis- played.

u Press either of the buttons to set the current date. v Press the Mode button to end.

r Temperature Setting

Setpoint

The thermostat normally displays the actual temperature. To view the setpoint, press the or button briefly. The setpoint will appear for the next 5 seconds.

To change the setpoint, press the or button until the desired temperature is displayed. To scroll faster, hold the button.

Using a preset temperature

The thermostat has 3 preset temperatures:

Comfort temperature

Economy temperature

Vacation temperature

???To use the Comfort or Economy temperature, press the or button respectively. The corresponding icon will be displayed.

???To use the Vacation temperature, press both and buttons simultaneously. The icon will be displayed.

Storing a preset temperature

To store the Comfort or Economy temperature:

Set the desired temperature using the or button. Press and

hold the appropriate button ( or ) for approximately 3 sec- onds until the corresponding icon is displayed.

To store the Vacation temperature:

Set the desired temperature using the or button. Press and hold both and buttons simultaneously for approximately 3 seconds until the icon is displayed.

s Modes of Operation

Automatic - The temperature is set according to the programmed schedule. To place the thermostat in this mode, press the Mode but- ton until is displayed. The icons of the current period and preset temperature are also displayed.

Temporary Bypass: If you modify the setpoint (by pressing the

, , or button) when the thermostat is in automatic mode, the new setpoint will be used until the end of the current period. When the next period starts, the temperature set for that period becomes the new setpoint. To cancel the bypass, press the Mode button.

Manual - The programmed schedule is not used. The temperature must be set manually. To place the thermostat in this mode:

n Press the Mode button until is displayed.

o Set the temperature using the , , or button.

t Schedule

The schedule consists of 4 periods per day which represents a typi- cal weekday. You can program the thermostat to skip the periods that do not apply to your situation. For example, you can skip periods 2 and 3 for the weekend.

Wake

Leave

Return

Sleep

The Comfort ( ) temperature is used in periods 1 and 3 and the Economy () temperature is used in periods 2 and 4. For example, when the period changes from 1 to 2, the setpoint automatically changes from Comfort setting ( ) to Economy setting ( ).

You can have a different program for each day of the week; i.e., each period can start at different time for each day of the week. The thermostat has been programmed with the following schedule.

To modify the schedule:

nPress Pgm to access the programming mode. Period 1 is selected.

oPress Day to select the day to program (hold for 3 seconds to select the entire week).

pPress Hour and Min to set the start time of the selected period, or press Clear if you want to skip the period (--:-- is displayed).

qPress Pgm to select another period, or press Day to select another day. Then repeat step 3.

r Press Mode to exit the programming mode.

NOTE: If no button is pressed for 60 seconds, the thermostat will automatically exit the programming mode.

u Power Outage

During a power outage, LP (Low Power) appears for the first minute. Then the screen becomes blank. The settings are stored in memory. However, if the power failure exceeds 4 hours, the thermostat???s clock must be re-adjusted and, if you are using the automatic Daylight Sav- ings Time changeover function, it must be re-enabled. When power returns, the thermostat will return to the mode of operation active prior to the power failure.

v Troubleshooting

w Technical Specifications

Power: 120/240 VAC, 60 Hz

Minimum load: 2 A (resistive only) 250 W @ 120 VAC 500 W @ 240 VAC

Maximum load: 16.7 A (resistive only) 2000 W @ 120 VAC 4000 W @ 240 VAC

Display range: 32??F to 140??F (0??C to 60??C)

Display resolution: 1??F (0.5??C)

Setpoint range: 40??F to 86??F (5??C to 30??C)

Setpoint interval: 1??F (0.5??C)

Storage: -4??F to 120??F (-20??C to 50??C)

; Warranty

Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option).

If the product is defective,

(i)return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or

(ii)call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT

BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,

INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH

OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY

HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF

ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limit??e, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.

Customer Assistance

If you have any questions about the operation of your thermostat, please go to http://yourhome.honeywell.com, or call Honeywell Customer Care toll-free at 1-800-468-1502.