Operation Manual
OSD Color Camera
???Thank you for choosing Honeywell
If you have any problems with this camera, contact your local supplier to service.
CAUTION for SAFETY OPERATION
1.Water and Moisture
To prevent fire or shock hazard, do not expose this camera to rain or moisture.
2.Servicing
Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards. Note that all servicing is qualified service personnel. Modifications not approved by manufacturer could
void the user's authority to operate the equipment.
3.Power Sources
To prevent electric shocks and risk of hazards, do NOT use more than the specified power source.
4.Environment
Do not install too warm or too cold place. Recommended operation temperature is between
5.Sunlight
Do not point the camera at the sun. CCD can be damaged.
6.Heavy Shock and Vibration
Do not drop the camera or subject it to heavy shock of vibration.
7.Install on an Unstable Place
Do not place or install this camera on an unstable place, stand, tripod, bracket or table. That may cause serious injury to people or damage to appliance.
8.When operation is incorrect or a malfunction is observed
While operating, if any abnormal condition (strange sound, smell or smoke) or a malfunction (no pictures, etc.) is observed, stop using the camera immediately, turn the power off, then contact your supplier.
9.Cleaning
Turn the power off and wipe off the dirt with a dry soft cloth. If it is extremely dirty, use furniture cleaner to wipe it off. To clean the lens, use a blower or lens cleaning tissue. (available from any camera dealer)
10.Do not shoot any source of bright light.
If the objects contain very bright areas, bright vertical or horizontal lines may appear on the screen. This is called "smear" , a Phenomenon which often occurs with solid
-state pickups, and is not a malfunction.
11.Damage Requiring service
Unplug the camera from the power source and refer servicing to qualified service personnel under the following condition:
A.If the
B.If the camera has been exposed to rain or water.
C.If liquid has been spilled, or objects have fallen into the camera.
D.If the camera does not operate normally by following the operating instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the camera to its normal operation.
E. If the camera has been dropped or the cabinet has been damaged. F . If the camera exhibits a distinct change in performance.
G. Warranty is not covered in case of natural disaster or wrong Installation.
INSTRALLATION
Mounting a lens
1.Remove the Protective cap in front of the camera.
2.Confirm the mount ring whether it is for C or CS.
3.Attach the lens to the lens mount ring.
4.If the lens has an Auto Iris mechanism, connect the iris cable to the
LENS in rear of the camera.
??? In the case of having no iris amplifier : Set the slide switch to DC (Down side).
???In the case of having iris amplifier : Set the slide switch VSD (Upper side)
???When connecting Auto iris lens, be sure to use the connector to be recommended by manufacturer.(
Back focus adjustment
1. In case of fixed focus lens
???Loosen the locking ring with L type wrench and set the focus ring of lens to infinity ( ??? ).
???Tune the mount ring to get a clear picture( distance from camera to object is more than 23m) and fasten the locking ring.
2. In case of zoom lens
???Loosen the locking ring with L type wrench and set the lens to the maximum telephoto position. Then turn the focus ring to focus.
???In the case of Auto iris lens only, shoot a comparatively dark object or reduce the ambient light so that the aperture is fully open.
???Set the lens to its maximum wide angle position, and set the focus. ??? Repeat step ??? and ???, until the difference between focusing
position ??? and ??? is smallest.
??? When the best focusing point in found, fasten the locking ring.
Connection of power supply
Must be checked the power source from the external power supply before power on.
The contents of the package
Check the below contents
-
-Auto Iris Lens Plug
-L Type Wrench
-Operation Manual (English)
TROUBLESHOOTING
NAMES & FUNCTIONS
OSD MENU
SPECIFICATIONS
Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center.
In case of no image
Is the coaxial cable attached securely? Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly?
In case of unclear image
Is the lens in focus?
Is the lens dirty?
Is the monitor adjusted correctly?
???Dirt of fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).
DIMENSIONS
UP BUTTON
ENTER BUTTON
POWER ON LED
This LED is ON
in power ON state.
DOWN BUTTON
(+) BUTTON
LENS CONNECTOR
+ - MD
VIDEO OUTPUT
Composite Video
Signal Output
GENERAL SETUP
CAMERA SETUP
MEM FUNC. SETUP
SPECIAL SETUP
Unit: mm
LENS
ENTER
VIDEO
CONT
POWER
Lens Type Select Switch
DC Lens: with no iris amp.
VSD Lens: with iris amp.
Power Input Terminal and MD Alarm Output
DEFAULT SETUP
EXIT SETUP
DC VSD
+-