EDGE SANDER

MODEL G1140

INSTRUCTION MANUAL

COPYRIGHT ?? 1996 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

REVISED APRIL, 1999. PRINTED IN U.S.A.

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substi- tute for proper accident prevention measures.

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DON???T USE IN DANGEROUS ENVIRON- MENT. Don???t use power tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

6.MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.DON???T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Don???t force tool or attachment to do a job for which it was not designed.

Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safe- ty glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It???s safer than using your hand and frees both hands to operate tool.

13.DON???T OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in.

17.USE RECOMMENDED ACCESSORIES.

Consult the owner???s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Don???t leave tool until it comes to a complete stop.

Additional Safety Instructions For Sanders

1.MAINTAIN A SECURE GRIP ON THE WORKPIECE. The belt speed is approxi- mately 1800 FPM. If control is lost, the workpiece can be propelled from the machine at extreme speed.

2.CREATE A SAFETY ZONE AROUND THE SANDING SURFACE. If you can't control your workpiece with your hands at least 6" away from the sanding belt, you should create a jig or other device to hold the workpiece safely.

3.REPLACE BELTS WHEN WORN OR DAMAGED. A torn or damaged belt could be unexpectedly expelled from the machine if not replaced.

4.KEEP YOUR WORKPIECE SOLIDLY ON THE SANDER TABLE. A well-secured workpiece is less likely to lose control dur- ing sanding operations.

5.INSPECT MATERIALS FOR DEFECTS.

Knots and splinters can shoot from the machine with great force. Make sure defective materials are not used on the belt sander. Foreign objects such as nails and staples should also be removed before sanding.

6.TURN OFF THE SANDER WHEN NOT IN USE. Never leave a machine running unattended.

7.DO NOT stand directly in line with sanding accessories when turning the machine on.

8.DO NOT force the workpiece against the belt during operation. Firmly grasp the workpiece in both hands and ease it against the belt using light pressure.

9.DO NOT wear loose clothing while operat- ing this machine. Roll up sleeves or button sleeves at the cuff.

10.DO NOT place hands near, or in contact with belt during operation.

11.WEAR A DUST MASK OR RESPIRA- TOR when sanding, even if you have a reliable method of dust collection.

12.PERFORM MACHINE INSPECTIONS and maintenance service promptly when called for.

Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glass- es or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI).

No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- ment or poor work results.

SECTION 2: CIRCUIT REQUIREMENTS

220V/110V Operation

The Model G1140 has a dual-voltage 11???2 HP, 1720 RPM motor which has been pre-wired for use in a 220V single phase circuit. The cord set enclosed does not have a plug as the style of plug you require will depend upon the type of service you currently have or plan to install. If you will be installing a new receptacle and plug, we recommend either of the styles shown in Figure 1. Note that you have the choice between simple plug-in and twist-lock plug styles.

Should you prefer to utilize the 110V capability, a wiring diagram is provided near the back of this manual showing the wiring changes needed. Operating at 110V will also require installing a grounded plug.

Circuit Load

The Model G1140 will draw approximately 8 amps at 220V and 16 amps at 110V. Circuit pro- tection when operating at 220V should be on a breaker rated at 15 amps or a fuse rated at 20 amps. At 110V a 20 amp slow-blow fuse or breaker should be used. Fusing at amperage rat- ings higher than these will not adequately protect the motor from high heat caused by overloading. You are cautioned that equipment returned to us for service that shows evidence of being over- fused will be repaired or replaced totally at the customer???s expense, regardless of the present warranty status.

Be aware that other machines operating on the same circuit simultaneously will also add load which can cause the circuit protection system to trip.

Figure 1. Two typical outlet/plug configurations.

Grounding

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor which must be properly connected to a grounding plug. The plug must be inserted into a matching outlet that is properly installed and grounded in accor- dance with all local codes and ordinances.

Improper connections of the electrical-grounding conductor can result in risk of electric shock. The conductor with green or green and yellow striped insulation is the electrical-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal.

This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate 12 A.W.G. copper grounding wire from the outlet to a known ground. Under no circumstances should the grounding pin from any three- pronged plug be removed. Serious injury may occur.

We do not recommend the use of extension cords on 220V equipment. It is much better to arrange the placement of your equipment and the installed wiring to eliminate the need for exten- sion cords. Should it be necessary to use an extension make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in Section 1: Safety Instructions to determine the minimum gauge for the extension cord. The extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged.

Your G1140 machine comes pre-wired for 220 volt operation. A wiring diagram is provided at the back of this manual should it be necessary to repair or revise the wiring. Always utilize a quali- fied electrician when doing any electrical work on this equipment.

We have covered some basic electrical requirements for the safe operation of your Edge Sander. These requirements are not necessarily comprehensive. You must be sure that your particular electrical configu- ration complies with local and state codes. Ensure compliance by checking with your local municipality or a licensed electrician.

SECTION 3: GENERAL INFORMATION

Commentary

We are proud to offer the Grizzly Model G1140 Edge Sander. The Model G1140 is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzly???s commitment to customer satisfaction.

The Model G1140 is intended for home and medi- um-duty professional use. This sander features a 1,720 RPM, 11/2 HP capacitor-start motor, mechanical ON/OFF switch, 4'' dust port and a cast iron working table. All running parts utilize shielded ball bearings, which require no lubrica- tion for the life of the bearings.

We are also pleased to provide this manual with the Model G1140. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. It repre- sents our effort to produce the best documenta- tion possible. If you have any comments regard- ing this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227-2069

Most importantly, we stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: http://www.grizzly.com

The specifications, drawings, and photographs illustrated in this manual represent the Model G1140 as supplied when the manual was pre- pared. However, owing to Grizzly???s policy of con- tinuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Whenever possible, though, we send manual updates to all owners of a particular tool or machine. Should you receive one, we urge you to insert the new information with the old and keep it for reference.

To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its characteristics as possible. The time you invest before you begin to use your Model G1140 will be time well spent. DO NOT oper- ate this machine until you are completely famil- iar with the contents of this manual. Make sure you read and understand all of the safety pro- cedures. If you do not understand something, DO NOT operate the machine.

Unpacking

This G1140 Edge Sander is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you???ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing mate- rials for possible inspection by the carrier or its agent. Without the packing materials, filing a freight claim can be difficult. If you need assis- tance determining whether you need to file a freight claim, or with the procedure to file one, please contact our Customer Service.

The G1140 is a very heavy machine (250 lbs. shipping weight). DO NOT over-exert your- self while unpacking or moving your machine ??? get assistance. In the event that your machine must be moved up or down a flight of stairs, be sure that the stairs are capable of supporting the combined weight of people and the machine. Serious person- al injury may occur.

When you are completely satisfied with the con- dition of your shipment, you should inventory its parts.

NOTICE

Please keep all packaging materials until you are satisfied that the machine is in good condition. Should you need to file a freight claim, the carrier???s agent will require inspection of those materials. Settling a claim can be difficult if packaging is not available.

Piece Inventory

After all the parts have been removed from the carton, you should have:

???Sanding unit

???Sanding Table

???Trunnions (2)

???Table Bracket w/ Lead Screw

???Lead Screw Bracket

???Hand Wheel

???Stabilizing Bracket

???Stabilizing Post

???Lock Handles (2)

???Plastic Knob

???Lever Handle

???Auxiliary Table w/ Post

???Dust Port

???6'' x 80'' Sanding Belt

???Back Stop

???Phillips?? Hd Screw 10-24 x 3/4'' (4)

???Feet (4)

???Miter Body

???Hex Bolt 5???16"- 18 x 1" (2)

???Flat Washer 5???16" (2)

???Flat Washer 3???8" (2)

In the event that any non proprietary parts are missing (e.g. a nut or a washer...), we would be glad to replace them, or, for the sake of expedi- ency, replacements can be obtained at your local hardware store.

Figure 2. Overview of all the parts.

The unpainted surfaces are coated with a waxy oil to protect it from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser. Avoid chlo- rine-based solvents as they may damage painted surfaces should they come in contact. Always fol- low the usage instructions on the product you choose for clean up.

Many of the solvents commonly used to clean machinery can be highly flammable, and toxic when inhaled or ingested. Always work in well-ventilated areas far from potential ignition sources when dealing with solvents. Use care when disposing of waste rags and towels to be sure they do not create fire or environmental hazards. Keep children and animals safely away when cleaning and assembling this machine.

Do not use gasoline or other petroleum- based solvents to remove this protective coating. These products generally have low flash points which makes them extremely flammable. A risk of explosion and burning exists if these products are used. Serious personal injury may occur.

All die-cut metal parts have a sharp edge (called ???flashing???) on them after they are formed. This is generally removed at the factory. Sometimes a bit of flashing might escape inspection, and the sharp edge may cause cuts or lacerations when handled. Please examine the edges of all die-cut metal parts and file or sand the edge to remove the flashing before handling.

-8-

1.Floor Load: Your G1140 Sander represents a large weight load in a small footprint. Most commercial floors are suitable for the Model G1140. Some residential floors may require additional build up to support both machine and operator.

2.Working Clearances: Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a home for your edge sander. Allow sufficient room to safely run your machines in any foresee- able operation.

3.Lighting and Outlets: Lighting should be bright enough to eliminate shadow and pre- vent eye strain. Electrical circuits should be dedicated or large enough to handle amper- age requirements. Outlets should be located near each machine so power or extension cords are clear of high-traffic areas. Observe local electrical codes for proper installation of new lighting, outlets, or circuits.

Be certain that this machine is properly grounded before attempting to use it. If you are unsure of the quality and condition of the circuit you intend to use, have it inspect- ed and repaired by a qualified electrician.

NOTICE

Ensure that the Model G1140 is located on a flat, level surface. This will maximize the stability of the machine and ensure that adjustments are accurate. For conditions where permanent mounting is possible, we recommend bolting the Edge Sander to your floor. This type of mounting will mini- mize vibration and provide a more stable work environment.

G1140 Edge Sander

SECTION 4: ASSEMBLY

Assembly of the G1140 is straightforward. We have organized the assembly process into steps. Please follow them in sequence.

Tools Required: Only a few common tools are needed to assemble this machine. Specifically, a 6" adjustable wrench, 12mm open end wrench, regular and Phillips?? screwdriver and an 8mm Allen?? wrench.

All die-cut metal parts have a sharp edge (called ???flashing???) on them after they are formed. This is generally removed at the factory. Sometimes a bit of flashing might escape inspection, and the sharp edge can cause cuts or lacerations when handled. Please examine the edges of all die-cut metal parts and file or sand the edge to remove the flashing before handling them. Serious injury may occur.

This machine is very heavy and can be awk- ward to handle without help. Get assistance during periods of assembly which require that the machine or any of its major compo- nents be moved, tilted, or carried. Failure to use proper lifting techniques could result in serious injury or damage to the machine.

1.Carefully lay the machine over on its side. Have someone assist you when doing this. Do not attempt to lay the machine over by yourself.

2.Install the four feet using the 10-24 x 3???4'' Phillips?? Head Screws provided. Figure 3. Get assistance and upright the machine.

Figure 3. Installing the feet.

Working Table

1.Bolt the lead screw bracket to the front of the stand using the four Hex Bolts already threaded in place. See Figure 4.

Figure 4. Lead screw bracket Installed.

2.Thread the horizontal brace into position, but do not tighten; the brace will require further adjustment later on. See Figure 5.

Figure 5. Installing the horizontal brace.

3.Locate the lead screw/table bracket assem- bly and the handwheel. Thread the hand- wheel onto the lead screw about halfway and insert the lead screw into the lead screw bracket. See Figure 6.

Figure 6. Installing the lead screw assembly.

4.Locate the vertical brace. Turn the horizontal brace approximately 45?? and insert the verti- cal brace through the hole at the end of the horizontal brace. Rotate the horizontal / ver- tical brace assembly to 90??.

5.Install the hex nut and washer provided, and screw on until 1???2'' of the threaded end is vis- ible above the washer. Insert the threaded end of the vertical brace through the hole in the bottom of the table bracket and re-install the flat washer and hex nut back onto the shaft. See Figure 7.

Figure 7. Horizontal / vertical brace installed.

6.Measure the table bracket to the stand to assure it is parallel to the stand. See Figure 8. If the bracket is not parallel, remove the vertical brace, thread the horizontal brace in or out an appropriate amount and reinstall the vertical brace.

Figure 8. Checking table bracket for parallelism.

7.Once the table bracket has been properly adjusted, tighten the horizontal brace jam nut and the two hex nuts that hold the verti- cal brace in place.

8.Attach the table trunnions to the table brack- et. Each is held in place with a 3/8'' flat wash- er and lock handle. See Figure 9. The trun- nion with the scale attaches to the left side.

Figure 9. Table trunnions installed.

9.Leaving the table trunnion lock handles slightly loose, bolt the working table to the trunnions using the two (2) 5???16''-18 x 3???4'' hex bolts and 5???16'' flat washers supplied. See Figure 10. Adjust the table so it is approxi- mately 1???8'' to 3???16'' from the edge of the sand- ing platen and tighten down the mounting bolts.

Figure 10. Attaching the working table.

10.Adjust the work table 90?? to the sanding plat- en by checking it with a square. Adjust as necessary and tighten the table lock han- dles. At this time adjust the pointer to 90??.

See Figure 11.

Figure 11. Setting the pointer to 90??.

Set the miter body onto its pivot hole and secure into place with the plastic lock knob provided. See Figure 12. The miter body should only be used when sanding the ends of workpieces at least 8'' long. Do not use it as a back stop.

Figure 12. Attaching the miter body.

Be certain that this machine is properly grounded before attempting to use it. If you are unsure of the quality and condition of the circuit you intend to use, have it inspect- ed and repaired by a qualified electrician. Failure to ensure proper grounding could result in fatal or serious injury and/or equip- ment damage.

Make your workshop child-safe. Ensure that idle machines have their safety keys removed, sharp blades are stored safely out of reach, and that your shop is securely locked when your shop is not in use.

1.Loosen the belt tracking lock knob located at the top left of the machine.

2.Slide the quick release lever through the slot on the top of the platen cover. Thread it into place until it bottoms out. See Figure 13. It may be necessary to have an assistant push the idler roller back into the machine to allow the quick release lever to line up with the thread in the yoke.

Figure 13. Installing the quick release lever.

Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glass- es or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI).

Slide the auxiliary table into place as pictured in Figure 14. Tighten the two thumb screws when table is at desired working height. It is not nec- essary to have the auxiliary table mounted at all times and can be installed only when needed.

Figure 14. Installing the auxiliary table.

Bolt the dust hood on using the hex bolts already threaded in place. See Figure 15.

Figure 15. Dust hood mounted in place.

Operating this equipment has the potential for respiratory damage to occur due to the level of airborne dust it produces. Always use a dust collection system AND wear a dust mask or respirator to avoid breathing wood dust. Serious personal injury may occur.

Attach the back stop as shown in Figure 16. Set the back stop no more than 1???8'' from the sandpa- per. This will prevent objects from being jammed between the back stop and the platen causing a potentially dangerous situation.

Figure 16. Back stop properly installed.

DO NOT attempt to operate this machine without this back stop in place and properly adjusted as described above. An improper gap between the stop and the belt can cre- ate a situation where a finger or hand can get trapped against the moving belt. Serious injury could occur.

1.Loosen the belt tracking lock knob on the top left of the machine. Open the lid of the dust port and move the quick release lever to its locked open position. See Figure 17.

Figure 17. Sander ready for belt installation.

2.Check the back side of the belt for an arrow indicating direction of rotation. The sanding belt rotates counter-clockwise.

3.Slide the belt over the rollers. Move the quick release lever back to its tensioned position. See Figure 18. Belt tracking is covered in the next section.

Figure 18. Belt installed.

SECTION 5: ADJUSTMENTS

1.Carefully move the belt left to right by hand and adjust the tracking knob as necessary to achieve proper tracking. See Figure 19.

2.Before beginning this step, read the entitled Test Run on page 18. Connect to power and turn the machine on and off quickly. If the belt appears to track OK turn the machine on and fine tune the tracking. Tighten the track- ing lock knob.

Figure 19. Location of tracking knob.

Moving sanding belts are dangerously abrasive. Use extreme caution when work- ing near sanding surfaces. Use extreme caution while making adjustments that require momentary or extended operation of the edge sander. Failure to exercise care while sanding could result in severe injury.

Loosen the thumb screws, position the auxiliary table, re-tighten the thumb screws. See Figure 20. Note that the ends of the roller are tapered. This helps keep the belt tracked. When using the end roller for curved sanding, we recommend you use the center portion of the roller to assure prop- er belt tracking. This also prevents the edge of the workpiece from becoming tapered.

Figure 20. Table adjustment thumbscrews.

1.Loosen the lock handles, tilt the working table to the desired angle and retighten the lock handles. See Figure 21.

2.It may be necessary to re-adjust the working table closer to the platen. Not more than a

1???4'' gap should exist between the platen and the working table.

Figure 21. Table tilt adjustment.

1.Loosen lead screw lock handle and stabiliz- ing shaft lock bolt. See Figure 22.

2.Turn hand wheel and position working table to desired height.

3.Retighten lock handle and lock bolt.

Figure 22. Table height adjustment.

1.Loosen the lock bolt shown in Figure 23.

2.Carefully tilt the platen assembly over.

Figure 24.

3.After returning the platen assembly back to its upright position, retighten the lock bolt depicted in Figure 23.

Figure 23. Platen lock bolt.

Figure 24. Platen tilted over 90??.

Belt tension is preset at the factory and usually requires no adjustment. If the need to increase the tension should occur, unthread the retaining nut at the end of the idler roller mounting shaft. See Figure 25. Do not unthread the nut more than 1???2 its length. If tension problems persist, call the service center for further help.

Figure 25. Belt tension mechanism.

Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glass- es or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI).

SECTION 6: OPERATIONS

Once the assembly is complete and the adjust- ments are done to your satisfaction, you are ready to test the machine.

Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there???s a problem. The edge sander should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before operating the machine further.

If noises occur that can not be found by visual inspection, feel free to contact our service depart- ment for help.

If the sander runs smoothly, try sanding a piece of lumber. If a problem exists, stop the machine and review all the adjustments. Call for assis- tance, if needed.

Use extreme caution when preparing for your initial test run. Always keep one finger on the STOP button in order to quickly shut off the machine in the event of a malfunc- tion.

DO NOT attempt to investigate or adjust the machine while the machine is still running. Turn off the machine and disconnect it from its power source before attempting any repair or adjustment. Serious operator injury could occur if this guideline is not fol- lowed.

Figure 26 depicts a typical edge sanding process. The back stop can be used for shorter workpieces if so desired.

Figure 26. Typical edge sanding method.

Figure 27 depicts a typical method for sanding the end of a workpiece.

Figure 27. Typical end grain sanding method.

When face sanding, tilt the platen so it is hori- zontal and use the back stop to hold your work- piece. Apply even hand pressure while moving the workpiece back and forth for even belt wear.

Figure 28. Typical face sanding method.

Sanding surfaces are capable of causing serious personal injury if they come in con- tact with fingers, hands or other body parts. Use extreme care to provide a large buffer area between the sanding belt and any part of your body.

When contour sanding, adjust the auxiliary table up or down so the workpiece is roughly centered on the roller. Move the workpiece over the roller to achieve your desired profile.

Figure 29. Typical contour sanding method.

Do not operate this equipment when wear- ing loose clothing, gloves, neckties, rings, bracelets or other jewelry which might get caught in the moving belt or trapped between the belt and the tables. Serious personal injury may result.

SECTION 7: MAINTENANCE

Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary.

1.Loose mounting bolts.

2.Worn switch.

3.Worn or damaged cords and plugs.

4.Damaged sanding belt.

5.Any other condition that could hamper the safe operation of this machine.

Lubrication

Shielded and pre-lubricated ball bearings require no lubrication for the life of the bearings. In a con- tinuous-use environment, expect the bearings to last for several years. With intermittent use, bear- ings can be expected to last much longer. All bearings are standard sizes and can be easily replaced.

The table and other non-painted surfaces on the Model G1140 should be protected against rust and pitting. Wiping the sander clean after every use ensures that moisture from sander dust isn???t allowed to trap moisture against bare metal sur- faces.

Some woodworkers recommend using automo- tive paste wax on exposed steel and cast iron surfaces. The wax provides a layer of protection, as well as reducing friction between lumber and the table, making cuts faster and smoother. Avoid waxes that contain silicone or other synthetic ingredients. These materials can find their way into lumber that???s being worked, and can make staining and finishing difficult. If you use paste wax, make sure that it???s 100% Carnauba wax.

SECTION 8: CLOSURE

The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G1140 Edge Sander.

If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service technicians will be glad to help you.

If you have comments dealing specifically with this manual, please write to our Bellingham, Washington location using the address in Section 3: General Information. The specifications, draw- ings, and photographs illustrated in this manual represent the Model G1140 as supplied when the manual was prepared. However, due to Grizzly???s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Whenever possible, though, we send manual updates to all owners of a particular tool or machine. Should you receive one, add the new information to this manual and keep it for refer- ence.

We have included some important safety meas- ures that are essential to this machine???s opera- tion. While most safety measures are generally universal, Grizzly reminds you that each work- shop is different and safety rules should be con- sidered as they apply to your specific situation.

Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate standards of the American National Standards Institute (ANSI).

We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3: Introduction.

Additional information sources are necessary to realize the full potential of this machine. Trade journals, woodworking magazines, and your local library are good places to start.

The Model G1140 was specifically designed for sanding. DO NOT MODIFY AND/OR USE

THIS MACHINE FOR ANY OTHER PUR- POSE. Modifications or improper use of this tool will void the warranty. If you are con- fused about any aspect of this machine, DO NOT use it until you have answered all your questions. Serious personal injury may occur.

Like all power tools, there is danger associ- ated with the Model G1140 Edge Sander. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

GRIZZLY MODEL G1140 HEAVY DUTY EDGE SANDER

Specifications, while deemed accurate, are not guaranteed.

REVISED 4/99

220VOLT

GREEN (GROUND)

TO 220 VOLT

POWER SUPPLY

-24-

45

44A

63

49A 103

46A

50

49

47

51 48

43

40

104

33

36

28

5

83

81

105

1

26

30

35A

29

9

10

11

23 13

12

50

78

52

51

103

63

91 60 58

57

62

68

67

76

55

79

56

59

61

92

3

4

91

81 74

38

39

23

25 35A

24

76

41 42

32

72

64

27

4

22

76

102

101

16

84

20A

14

15

17

63 75

97

Edge G1140

95

7

8

6

69

74 73

19

18

Sander

71

66

65

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly???s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly???s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe- cial, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a ???Return Number??????, which must be clearly posted on the outside as well as the inside of the car- ton. We will not accept any item back without this number. Proof of purchase must accompany the mer- chandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

WARRANTY CARD

Name ____________________________________________________________________________________

Street ____________________________________________________________________________________

City ______________________________________________________________State________Zip_________

Phone Number_______________________E-Mail_______________________FAX________________________

MODEL # ______________________________Order #______________________________________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

1.How did you learn about us?

___Other__________________________________________________

2.Which of the following magazines do you subscribe to.

___Other__________________________________________________

3.Which of the following woodworking/remodeling shows do you watch?

___Other__________________________________________________

4.What is your annual household income?

___$20,000-$29,999___$60,000-$69,999

5.What is your age group?

6.How long have you been a woodworker?

7.How would you rank your woodworking skills?

8.What stationary woodworking tools do you own? Check all that apply.

___Other__________________________________________________

9.How many of your woodworking machines are Grizzly? _____________

10.Which benchtop tools do you own? Check all that apply.

___Other__________________________________________________

11.How many of the machines checked above are Grizzly? ____________

12.Which portable/hand held power tools do you own? Check all that apply.

___Other__________________________________________________

13.What machines/supplies would you like Grizzly Industrial to carry?

___Other__________________________________________________

14.What new accessories would you like Grizzly Industrial to carry?

___Other__________________________________________________

15.What other companies do you purchase your tools and supplies from?

__________________________________________________________

__________________________________________________________

16.Do you think your purchase represents good value?

17.Would you recommend Grizzly Imports to a friend?

18.Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times.

19.Comments:_________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

CUT ALONG DOTTED LINE

G1140 Edge Sander

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE