JUNIOR ELECTRIC GUITAR KIT

MODEL H7582

INSTRUCTION MANUAL

COPYRIGHT ?? AUGUST, 2005 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL7247 PRINTED IN CHINA

SECTION 1: SAFETY

Always wear safety glasses or goggles when operating equipment. Everyday glasses or read- ing glasses are not safety glasses. Be certain the safety glasses you wear meet the appropri- ate standards of the American National Standards Institute (ANSI).

Because there are various ways to cut and join wood, you can make substitutions for the methods stated in this plan. We try to suggest the easiest methods possible. However, only you know your skills with each piece of machinery. Never compromise your safety by using a cutting method with which you are not comfortable. Instead, find an alternative approach that will yield the same result.

These instructions assume that you are intimately familiar with the safe operation and use of woodworking machinery and woodworking tools, and understand the techniques used to build this project. If you do not qualify for both of these criteria, STOP building this project for your own safety. Read and understand the owners manual for the machinery you intend to use, take a wood- working class or visit your local library for more information. Woodworking machinery and tools are inherently dangerous because they use sharp edges that can and will cause serious personal injury including amputation and death. Do not underestimate the ability of these tools and machin- ery to cause injury. Never operate any tool without all guards in place and always wear approved safety glasses. For your own safety, please heed this warning.

SECTION 2: INTRODUCTION

Foreword

We are proud to offer the Model H7582 Junior Electric Guitar Kit. This kit is a part of a grow- ing Grizzly family of fine woodworking products. When assembled according to the guidelines set forth in this manual, you can expect years of enjoyment from your guitar.

We are pleased to provide this manual for the Model H7582 Junior Electric Guitar Kit. It was written to guide you through assembly, review safety considerations, and cover general informa- tion. It represents our effort to produce the best documentation possible.

Contact Info

If you have any comments regarding this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

We stand behind our products. If you have any service questions or parts requests, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: http://www.grizzly.com

The specifications, drawings, and photographs illustrated in this manual represent the Model H7582 Junior Electric Guitar Kit as supplied when the manual was prepared. However, owing to Grizzly???s policy of continuous improvement, changes may be made at any time with no obliga- tion on the part of Grizzly. For your convenience, we always keep current Grizzly manuals available on our website at www.grizzly.com. Any updates to products will be reflected in these manuals as soon as they are complete. Visit our site often to check for the latest updates to this manual!

SECTION 3: PARTS INVENTORY

Inventory

2

Figure 1. Boxed components.

Figure 2. Guitar parts.

Figure 3. More guitar parts.

Model H7582 Junior Electric Guitar Kit

Supplies/Tools

The majority of the wooden components in this kit are fully machined from the factory and are ready for assembly. A small amount of sanding and finishing will need to be performed to complete your guitar.

Recommended Tools & Supplies:

???18" Metal Straightedge with a 1???32" Resolution

???ANSI Approved Respirator

???ANSI Approved Safety Glasses

???Aluminum-Oxide Sanding Paper #220 and #320 Grit

???Wet and Dry Sanding Paper #400, #600, and #1000 Grit (Optional)

???Tweezers or Pliers

???8, 10, 11, and 13mm Wrenches

???Flexible Sanding Block

???Phillips Screwdriver #1, #2

???Temporary Wood Neck: Approximately 1" x 2" x 16"

Model H7582 Junior Electric Guitar Kit

???Wood Screws #7 x 11???2" (4)

???Drill

???Drill Bit: 5???16"

???1???4" Steel Rod, or a Coat Hanger

???Masking Tape

???Tack Cloth or Clean Soft Rag

???Spray Primer and Finish (*See Note)

???Buffing Compounds (Optional)

???Soldering Iron and Solder

???Peghead Reamer or a Round File

???Hammer

???Wooden Block: Approximately 4" x 8"

???Guitar Capo

???Feeler Gauge Set

???Wire Cutters

???Rubber Cement

???9V Battery

Note: Use the same type of paint for primer and finish???either enamel or lacquer base. Do not use different base paints for priming or finishing or your results may not be desir- able.

-5-

Identification

SECTION 4: ASSEMBLY

Sanding the Body

The guitar body has been rough sanded at the factory, but it is up to you to do the final sanding before the finish is applied. To get a good finish, the body should be sanded with a series of sand- paper grits up to #320 grit.

To sand the guitar body:

1.Wear an ANSI-approved respirator and safety glasses when sanding!

2.Use a flexible sanding block with #220 grit sanding paper to sand the entire guitar body

and lightly round over the outside edges of the body. DO NOT round over the neck pocket or the body cavities.

3.Apply a coat of spray primer according to the primer manufacturer's instructions.

4.When the primer is dry, use #320 grit sandpa- per for final sanding. DO NOT sand through the primer to the bare wood.

Finishing the Body

Solid color finishes are available through hard- ware stores, auto paint suppliers or luthier supply catalogs. Finish materials and books on finish- ing instruments can be ordered through Grizzly Industrial. Painting an instrument is a difficult process with many options. If you are unsure of your skills, you can research finishing techniques and practice on scraps, or have a professional paint it for you.

Most finishes are hazard- ous to your health. Wear a NIOSH/OSHA approved res- pirator with particulate and gas/vapor filters, safety glasses, rubber gloves, and work in a well ventilated area when finishing.

To finish the guitar body:

1.Mask off the neck pocket. Press the masking tape tight against the edges of the pocket so the finish does not seep under the tape.

2.Fasten four wood screws through the neck pocket holes into a scrap piece of wood about 1" x 2" x 16". This will be used as a handle when spraying finish.

3.Drill a hole in the end of the handle for hang- ing from a hook.

4.Wipe the entire guitar body with a tack cloth or a soft clean rag to remove any dust.

5.Thread the hook through the temporary han- dle and hang the body in the finish room.

6.Apply several thin coats of the finish, follow- ing the manufacturer's instructions. Multiple thin coats usually produce a better quality finish than one heavy coat.

7.Allow to dry according to the manufacturer's instructions.

Note: Depending upon the type of finish used and environmental factors, drying time will vary.

To achieve an extremely high gloss finish with lacquer, follow these optional steps:

8.Sand the entire body with #400 grit wet and dry sandpaper after at least three coats of finish have been applied. DO NOT sand through the finish???be especially careful on the edges.

9.Apply more finish, sanding between coats, until the finish is the desired thickness.

10.Allow to dry according to the manufacturer's instructions.

Note: Depending upon the type of finish used and environmental factors, drying time will vary. Sometimes it may take up to a month for the finish to reach its full hardness.

-8-

11.Wet sand the finish using #600 grit wet/dry sandpaper on a sanding block, followed with #1000 grit sandpaper.

12.You may buff the finish by hand or with a buf- fer, starting with a medium polish and work- ing up to a high gloss polish.

Note: If using a buffing machine, be extreme- ly careful to avoid going through the finish, especially on the edges.

NOTICE

Dust particles suspended in the air will settle on wet finishes, causing less than sat- isfactory results. To avoid this problem:

???Leave the finish room undisturbed for 24 hours prior to applying the finish.

???Avoid making unnecessary movements upon entering the finish room.

???Apply the finish to the guitar parts and immediately leave the finish room.

???DO NOT return to the room until the specified drying time has elapsed.

Model H7582 Junior Electric Guitar Kit

The tuning head plate consists of six machine heads on a metal plate. The machine heads are attached to the headstock with bushings and small screws.

To install the tuners:

1.Place the six bushings into the holes on the face of the headstock (Figure 6). The holes may need to be widened with a peghead reamer or a round file. DO NOT widen the holes too much???the bushings should fit snugly.

Figure 6. Installing plastic bushings on head- stock.

2.Place a wooden block on the bushings and lightly tap the block with a hammer (Figure 7) until the bushings are seated against the face of the headstock.

NEW

NEW

PHOTO

PHOTO

Figure 7. Seating bushings.

3.Slide the machine heads through the bush- ings from the back face of the headstock.

4.Align the tuning head plate over the mounting holes and secure with #3 x 3???8" black screws as shown in Figure 8.

Figure 8. Tuning head plate installed correctly.

The neck is pre-finished and is ready to install.

To attach the neck to the guitar body:

1.Place the neck into the neck pocket (Figure 9). If the neck does not fit into the pocket, lightly sand the high points on the neck until it fits.

2.Place the neckplate over the neck pocket holes and thread four #7 x 13???4" silver screws (Figure 10) through the guitar into the neck. DO NOT use glue, since you may want to remove the neck for maintenance and tune- ups.

Figure 9. Neck installation.

-10-

Figure 10. Neckplate installation.

Model H7582 Junior Electric Guitar Kit

After the pickup, battery case, and speaker are installed, solder them onto the jacks and the cir- cuit board.

Pickup

The pickup is installed onto the front of the gui- tar.

To install the pickup:

1.Place the guitar face-side up.

2.Insert the pickup wire (Figure 11) through the hole in the pickup mortise and into the circuit board mortise.

Pickup

Wire

Hole

Figure 11. Pickup installation location.

3.Insert the pickup into the mortise, positioning both of the #3 x 3???4" black screws through a spring.

4.Secure the pickup to the guitar body with the black screws. Be careful NOT to thread the screws through the pickup wire.

5.Turn the guitar over so the back is face-side up.

6.Solder the pickup wire onto the volume con- trol as shown on the Wiring Diagram on

Page 23 and the Electrical Components photos on Page 24.

Speaker

To install the speaker:

1.Place the speaker mesh cover in the bottom of the speaker mortise

2.Align holes on the speaker with holes in the mortise and fasten the four #2 x 1???4" black screws.

3.Insert the two black wires on the headphone jack through holes in the circuit board mortise and battery case (Figure 12) and into the speaker mortise.

Figure 12. Speaker wires in battery case mortise.

4.Solder the speaker wires onto the speaker as shown on the Wiring Diagram on Page 23 and the Electrical Components photos on

Page 24.

Battery Case

To install the battery case:

1.Insert the battery case wires through the left hole in the battery case mortise and into the circuit board mortise.

2.Slide the battery case (Figure 13) into the mortise and secure with two #2 x 1???4" black screws.

AC/DC

Output

Headphone

Figure 14. Inserting jacks through jack plate.

4.Reinstall the nuts and washers removed in Step 1, using an 11 and 13mm wrench, then fasten the jack plate to the guitar with the two #3 x 1???2" silver screws (Figure 15).

Figure 13. Installing battery case.

Headphone, AC/DC & Output Jacks

To install the headphone, AC/DC, and output jacks:

1.Remove the hex huts and washers from the headphone, AC/DC, and output jacks.

2.Solder the battery wires onto the AC/DC jack as shown on the Wiring Diagram on Page 23 and the Electrical Components photos on Page 24.

3.Insert the headphone, AC/DC, and output jacks out through the hole in the side of the guitar, then through the jack plate (Figure 14).

Figure 15. Securing jack plate.

Volume, Tone & Circuit Board

To install the tone control, volume control, and power switch:

1.Remove hex nuts, flat washers, and interior tooth washers from the volume control, tone control, and power switch. Note the location of each of the nuts and washers. This will make it easier to reinstall the components.

2.Insert the volume and tone controls through flat washers and then into the sockets on the guitar body as shown in Figure 16.

Volume

Control

Tone

Control

Figure 16. Installing tone and volume controls.

3.Using a 10mm wrench, reinstall the nuts and washers removed in Step 1 and install the volume and tone control knobs.

4.Insert the grounding wire through the hole in the side of the circuit board mortise (Figure 17).

Note: It may help to use tweezers or pliers.

Hole

Grounding

Wire

Figure 17. Installing ground wire into side hole.

5.Thread the wire until it protrudes through the top of the guitar body. Place a piece of mask- ing tape over the wire to hold it temporarily.

1.Place the circuit board and the speaker cov- ers over the mounting holes (Figure 19) and secure each cover with four #2 x 1???4" black screws.

For the guitar to be grounded correctly, a section of exposed grounding wire must contact the bot- tom of the bridge.

To attach the bridge to the guitar body:

1.Make sure the end of the grounding wire fits snugly in the hole shown in Figure 20. The exposed wires should protrude past the hole enough to contact the bridge.

2.Secure the wire insulation in the hole with rubber cement, leaving the end exposed.

3.Align the mounting holes on the guitar and bridge (Figure 20) and secure over the ground wire with five #4 x 3???4" silver screws.

Figure 19. Covers secured.

Exposed

Section

Ground

Wire

Figure 20. Bridge placement.

1.Locate the mounting holes.

2.Secure the strap buttons with two #4 x 3???4" silver screws.

Figure 21. Strap buttons.

Winding Strings

The correct position of the guitar strings is shown in Figure 22. The thin High E string is called the "1st" string and the thick Low E string is called the "6th" string.

E6

5A4D

Figure 22. Correct string locations.

To install the guitar strings:

1.Slide the 1st string through the corresponding hole in the bridge (Figure 23).

First

String

Figure 23. Installing 1st string.

2.Guide the string through the bridge, over the saddle, over the nut, and through the hole in the corresponding tuner.

3.Allow only enough slack in the string for 2 or 3 rotations around the tuner.

Note: If too much slack is allowed, then the string could wind off the machine head after many successive rotations. If not enough slack is allowed, then the string may not hold the winding tension.

4.Bend the string at a right angle across the edge of the machine head.

5.Rotate the tuners until the string just begins to hold the winding tension, as shown in

Figure 24.

Note: DO NOT tighten the strings beyond the initial tensioning at this time. Final tensioning should be completed during the string tuning process.

Figure 24. String wrapped around tuner.

6.Repeat the above process for the remaining strings.

1.Slide a #2 x 1???2" silver screw through a retain- er and large bushing, and fasten it to the front hole on the headstock (Figure 25).

2.Slide a #2 x 3???8" silver screw through a retain- er and small bushing, and fasten it to the

back hole on the headstock (Figure 25).

SECTION 5: SET UP

General

Guitar set up is an art that requires skill, patience and experience. If you have the patience, you can acquire the skill and experience. If you don't have the patience, you may want to have your guitar set up by a qualified guitar technician.

This section on set up is a general overview of set up practices. We highly recommend that you research more in-depth methods. Books on set- ting up electric guitars can be ordered through Grizzly Industrial, luthier supply catalogs, or may be available through your local library.

Neck Adjustment

The guitar neck was adjusted perfectly straight before it was packaged; however, the moisture content of wood acclimates to the humidity of the surrounding environment. This characteristic results in movement of the wood components with regards to alignment. It is not uncommon for the neck to require adjustment several times each year, especially in regions where the sea- sonal climate changes are more drastic.

To adjust the bow of the guitar neck:

1.Tighten the strings to playing tension.

2.Place a straightedge from the 1st fret to the 17th. Measure any gaps between the straightedge and the frets with the feeler gauge.

???If the neck is flat, or bowed up .012" or less, the neck is set up correctly.

Model H7582 Junior Electric Guitar Kit

???If the gap is greater than .012", or if the neck bows away from the straightedge, continue to Step 3.

3.Remove the strings from the neck and the neck from the guitar body.

4.Turn the truss rod nut in the base of the neck (Figure 26) counterclockwise with a 5mm hex wrench to release tension on the neck. Retighten until the nut begins to grab.

Figure 26. Truss rod nut location.

5.To flatten a back bow, turn the truss rod nut a 1???4 turn clockwise. To correct an up bow, turn the nut a 1???4 turn counterclockwise.

6.Restring the guitar and recheck the neck with the straightedge. Use wire cutters to cut off excess string.

???If the neck is correctly adjusted, go to the next section.

???Return to Step 3 for further adjustment.

-17-

Fingerboard

Figure 28. Adjusting string height.

3. Remove the capo.

Figure 27. String height measurement.

Pickup Height

Setting Intonation

Pickup height can have a dramatic effect on the audio output signal. The closer the strings are to the pickup, the higher the audio output signal will be. If the strings are too close, distortion is caused by magnetic interference from the elec- tronic components.

To measure the string height at the pickup:

1.Measure the height of the 1st and 6th strings at the pickup while the strings are ???fretted??? at the 22nd fret (Figure 29).

Figure 29. String heights over the pickup.

2.With a Phillips head screwdriver, adjust the screws on each side of the pickup until the 1st string is 3???32" above the pickup and the 6th string is 1???8" above the pickup.

1.Lightly touch and then release the 1st string directly above the twelfth fret as you pluck the string to play a harmonic note.

2.Now pluck the string while holding it fretted at the twelfth fret. If this note is sharper than the note played in Step 1, move the saddle away from the neck by turning the Phillips head screw (Figure 30) clockwise. If this note is flat in comparison, move the saddle toward the neck.

Figure 30. Saddle adjustment location.

Note: This can also be done with an elec- tronic tuner by tuning the harmonic note to be exactly in tune and then adjusting the saddle until the note played in Step 2 is also in tune.

3.Repeat Steps 1???2 until the string is in tune. Repeat the process for the rest of the strings.

Tuning

Tuning is an important guitar concept. If the guitar is not in tune, the resulting sound is unpleasant. These instructions explain how to tune by ear. You can also tune using an electronic tuner such as the Grizzly H3097 Chromatic Tuner shown on

Page 21.

To tune the guitar:

1.Install a 9V battery into the battery case.

2.Play a Low E pitch on a piano, a tuning fork, or an electronic computer file.

3.Play an open (non-fretted) 6th string (Figure 31) and adjust the tuner to match the Low E.

Note: Always tune up. If the string is tuned high, loosen the string to lower the pitch, then tune the string up to the correct note.

E6

5A

4D

3 G

2 B

1 E

4.Tune the 5th string by playing the 6th string while it is being pressed (fretted) at the 5th fret, and then play the open 5th string. Adjust the 5th string tuner until the notes match.

5.Perform the same tuning steps on the 4th and 3rd strings.

6. When tuning the 2nd string, fret the 3rd string at the 4th fret instead of the 5th fret.

7.Tune the 1st string in the same manner as the 6th, 5th, 4th, and 3rd strings.

Basic Guitar Care

Use a clean, lint-free cotton cloth to wipe your gui- tar on a regular basis. Never use paper towels.

If you plan to store the guitar for several months, remove the battery, loosen the strings a little, and store in a place where the guitar will not experi- ence temperature or humidity extremes.

Figure 31. Standard tuning.

SECTION 6: REFERENCE INFO

Accessories

H2499???Small Half-Mask Respirator

H3631???Medium Half-Mask Respirator

H3632???Large Half-Mask Respirator

H3633???Disposable Cartridge Filter Pair

H3635???Disposable Cartridge Filter Pair

This lightweight elastomeric facepiece has cradle suspension, easy adjust headstraps and low profile for greater field of vision and compatibility with normal use of glasses or goggles. Purchase cartridges separately depending upon intended application.

H3633 protects against organic vapor, sulfur dioxide, hydrogen chloride and chlorine. H3635 protects against all particulate aerosols.

Figure 32. Half-mask respirator and disposable cartridge filters.

G7984???Face Shield

H1298???Dust Sealed Safety Glasses

H1300???UV Blocking, Clear Safety Glasses

H2347???Uvex?? Spitfire Safety Glasses

H0736???Shop Fox?? Safety Glasses

Safety Glasses are essential to every shop. If you already have a pair, buy extras for visitors or employees. You can't be too careful when it comes to shop safety!

G7984

Figure 33. Our most popular safety glasses.

H3097???Chromatic Tuner

An absolute must for any guitar player, this tuner allows you to tune your acoustic or electric guitar dead on. Includes 9V battery.

Figure 34. Model H3097 Chromatic Tuner.

H5750???Vinyl Washcoat/Sealer, 1 Qt H5751???Nitrocellulose Lacquer, Gloss, 1 Qt H5752???Nitrocellulose Lacquer, Gloss, 1 Gal H5753???Nitrocellulose Lacquer, Satin, 1 Qt H5754???Nitrocellulose Lacquer, Satin, 1 Gal

H5755???Retarder for Lacquer, 1 Qt

McFadden's nitrocellulose lacquer is the leading lacquer used by custom guitar builders. It sprays and buffs really well and is capable of giving you a finish that looks "wet."

Figure 35. Model H5750-59 McFadden's

Lacquers and Fillers.

H0818???Fine Prepolishing Paste, 1.85 lb H4873???Medium Prepolish Liquid, 1 Qt H0821???High Gloss Polishing Liquid, 1 Qt

Menzerna professional polishing compounds will remove any fine scratches from the finish and give your instrument the incredibly high gloss fin- ish that you are looking for.

Figure 36. Menzerna polishing compounds.

-22-

H3900???Clear Lacquer, Dead Flat, 13 Oz H3901???Cear Lacquer, Flat, 13 Oz H3902???Clear Lacquer, Gloss, 13 Oz H3903???Clear Lacquer, Satin, 13 Oz

Behlen Jet Spray???is specially formulated to enable the experienced as well as the novice to do a professional job. Two or three coats of the desired sheen will develop a durable, alcohol resistant lacquer finish. This product is economi- cal, easily applied and dries quickly.

H3936???Top Coat Lacquer, Gloss, 13 Oz H3937???Top Coat Lacquer, Satin, 13 Oz H3938???Top Coat Lacquer, Sealer, 13 Oz

Behlen Master Lacquer Top Coat is an alcohol and water resistant, high solid nitrocellulose lacquer. Use to seal and protect Behlen solvent based stains and other Master Aerosols.

Figure 37. Behlen clear and top coat lacquers.

Model H7582 Junior Electric Guitar Kit

Electrical Components

Volume Control Wiring

Red

Red

Black

Red

Black

Brown

Tone Control Wiring

White

Black

Headphone Jack Wiring

AC/DC Adapter Jack Wiring

Red

Black

Output Jack Wiring

Electrical Components

Wiring Diagram

?????????????????????

??????????????????

??????????????????

???????????????

??????????????????

?????????????????????

??????????????????????????????????????????

???????????????

???????????????

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly???s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly???s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a ???Return Number,?????? which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

CUT ALONG DOTTED LINE

WARRANTY CARD

Name_____________________________________________________________________________

Street_____________________________________________________________________________

City _______________________ State_________________________ Zip _____________________

Phone # ____________________ Email ________________________ Invoice #_________________

Model # ____________________ Order # _______________________ Serial #__________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

1.How did you learn about us?

2.Which of the following magazines do you subscribe to?

3.What is your annual household income?

4.What is your age group?

5.How long have you been a woodworker/metalworker?

6.How many of your machines or tools are Grizzly?

9.Would you allow us to use your name as a reference for Grizzly customers in your area?

10. Comments: _____________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Buy Direct and Save with Grizzly?? ??? Trusted, Proven and a Great Value!

Visit Our Website Today And Discover Why

Grizzly?? Is The Industry Leader!

???SECURE ORDERING

???ORDERS SHIPPED WITHIN 24 HOURS

???E-MAIL RESPONSE WITHIN ONE HOUR

-OR-

Call Today For A FREE

Full Color Catalog