MODEL G1183/G1276

HEAVY-DUTY

COMBINATION SANDER

OWNER'S Manual

Copyright ?? 1989 By Grizzly Industrial, Inc., Revised APRIL, 2011 (TS)

Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc.

(For models manufactured SINCE 3/10) #0335 printed IN TAIWAN

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury???including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and compre- hension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

???Lead from lead-based paints.

???Crystalline silica from bricks, cement and other masonry products.

???Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area, and work with approved safety equip- ment, such as those dust masks that are specially designed to filter out microscopic particles.

Table of Contents

INTRODUCTION

We are proud to offer this manual with your new machine! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the machine we used when writing this manual. However, sometimes we still make an occasional mistake.

Also, owing to our policy of continuous improve- ment, your machine may not exactly match the manual. If you find this to be the case, and the dif- ference between the manual and machine leaves you in doubt, check our website for the latest manual update or call technical support for help.

Before calling, find the manufacture date of your machine by looking at the date stamped into the machine ID label (see below). This will help us determine if the manual version you received matches the manufacture date of your machine.

For your convenience, we post all available man- uals and manual updates for free on our website at www.grizzly.com. Any updates to your model of machine will be reflected in these documents as soon as they are complete.

We stand behind our machines. If you have any questions or need help, use the information below to contact us. Before contacting, please get the serial number and manufacture date of your machine. This will help us help you faster.

Grizzly Technical Support 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663

Email: techsupport@grizzly.com

We want your feedback on this manual. What did you like about it? Where could it be improved? Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

Basic Controls

Having a good understanding of the basic con- trols of the sander is important to properly set up the machine and successfully complete the test run. Refer to Figure 5 and the following descrip- tions to gain this understanding.

Figure 5. Locations of the basic controls.

To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.

A.Upper Roller Adjustment Screws: Control the tilt of the upper roller and are used to make it parallel with the lower roller for track- ing purposes.

B.Sanding Belt Quick-Release Tension Lever: When pulled down, releases the ten- sion on the sanding belt for removal/installa- tion.

C.Sanding Belt Table Angle Scale: Displays the tilt angle of the belt table.

D.Sanding Belt Table Lock Lever: Locks the belt table in place after changing the tilt angle.

E.Sanding Disc Table Angle Scale: Displays the tilt angle of the disc table.

F.Sanding Disc Table Lock Knob (1 of 2):

Locks the disc table in place after changing the tilt angle.

G.ON/OFF Switch: Turns the sander ON and

OFF.

H.Belt Assembly Locking Cap Screw:

Secures the sanding belt assembly in place after changing its tilt position.

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 ?? To Order Call: (800) 523-4777 ?? Fax #: (800) 438-5901

MODEL G1183 COMBINATION SANDER 6" X 48" BELT 12"

DISC 3450 RPM

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 ?? To Order Call: (800) 523-4777 ?? Fax #: (800) 438-5901

MODEL G1276 COMBINATION SANDER 6" X 48" BELT 12"

DISC 1725 RPM

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

Safety Instructions for Machinery

OWNER???S MANUAL. Read and understand this owner???s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAzARdOUS dUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of work- piece control.

HEARING PROTECTION. Always wear hear- ing protection when operating or observiing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

??

DISCONNECTING POWER SUPPLY.??Always??dis- connect?? machine?? from?? power?? supply?? before?? ser- vicing,?? adjusting,?? or?? changing?? cutting?? tools?? (bits,?? blades,?? cutters,?? etc.).?? Make?? sure?? switch?? is?? in?? OFF?? position??before??reconnecting??to??avoid??an??unexpect- ed??or??unintentional??start.

APPROVED OPERATION.?? Untrained?? operators?? can?? be?? seriously?? hurt?? by?? machinery.?? Only?? allow?? trained?? or?? properly?? supervised?? people?? to?? use?? machine.?? When?? machine?? is?? not?? being?? used,?? dis- connect?? power,?? remove?? switch?? keys,?? or?? lock-out?? machine??to??prevent??unauthorized??use???especially?? around??children.??Make??workshop??kid??proof!

DANGEROUS ENVIRONMENTS. Do?? not?? use?? machinery?? in?? wet?? or?? rainy?? locations,?? cluttered?? areas,?? around?? flammables,?? or?? in?? poorly-lit?? areas.?? Keep?? work?? area?? clean,?? dry,?? and?? well-lighted?? to?? minimize??risk??of??injury.

ONLY USE AS INTENDED.?? Only?? use?? machine?? for?? its?? intended?? purpose.?? Never?? modify?? or?? alter?? machine??for??a??purpose??not??intended??by??the??manu- facturer??or??serious??injury??may??result!

USE RECOMMENDED ACCESSORIES.??Consult?? this??owner???s??manual??or??the??manufacturer??for??rec- ommended?? accessories.?? Using?? improper?? acces- sories??will??increase??the??risk??of??serious??injury.

CHILDREN & BYSTANDERS. Keep?? children?? and??bystanders??a??safe??distance??away??from??work?? area.??Stop??using??machine??if??children??or??bystand- ers??become??a??distraction.

REMOVE ADJUSTING TOOLS.?? Never?? leave?? adjustment??tools,??chuck??keys,??wrenches,??etc.??in??or?? on??machine???especially??near??moving??parts.??Verify?? removal??before??starting!

SECURING WORKPIECE.?? When?? required,?? use?? clamps??or??vises??to??secure??workpiece.??A??secured?? workpiece??protects??hands??and??frees??both??of??them?? to??operate??the??machine.

FEED DIRECTION.??Unless??otherwise??noted,??feed?? work?? against?? the?? rotation?? of?? blades?? or?? cutters.?? Feeding??in??the??same??direction??of??rotation??may??pull?? your??hand??into??the??cut.

FORCING MACHINERY.??Do??not??force??machine.?? It?? will?? do?? the?? job?? safer?? and?? better?? at?? the?? rate?? for?? which??it??was??designed.

GUARDS & COVERS.?? Guards?? and?? covers?? can?? protect?? you?? from?? accidental?? contact?? with?? moving?? parts?? or?? flying?? debris.?? Make?? sure?? they?? are?? prop- erly??installed,??undamaged,??and??working??correctly?? before??using??machine.

NEVER STAND ON MACHINE.??Serious??injury??or?? accidental?? contact?? with?? cutting?? tool?? may?? occur?? if?? machine??is??tipped.??Machine??may??be??damaged.

STABLE MACHINE. Unexpected??movement??dur- ing??operations??greatly??increases??the??risk??of??injury?? and?? loss?? of?? control.?? Verify?? machines?? are?? stable/ secure?? and?? mobile?? bases?? (if?? used)?? are?? locked?? before??starting.

AWKWARD POSITIONS.?? Keep?? proper?? footing?? and??balance??at??all??times??when??operating??machine.?? Do??not??overreach!??Avoid??awkward??hand??positions?? that?? make?? workpiece?? control?? difficult?? or?? increase?? the??risk??of??accidental??injury.

UNATTENDED OPERATION. Never?? leave??

machine??running??while??unattended.??Turn??machine?? off??and??ensure??all??moving??parts??completely??stop?? before??walking??away.

MAINTAIN WITH CARE.??Follow??all??maintenance?? instructions?? and?? lubrication?? schedules?? to?? keep?? machine??in??good??working??condition.??An??improperly?? maintained??machine??may??increase??the??risk??of??seri- ous??injury.??

CHECK DAMAGED PARTS.?? Regularly?? inspect?? machine?? for?? damaged?? parts,?? loose?? bolts,?? mis- adjusted?? or?? mis-aligned?? parts,?? binding,?? or?? any?? other?? conditions?? that?? may?? affect?? safe?? operation.?? Always??repair??or??replace??damaged??or??mis-adjust- ed??parts??before??operating??machine.

EXPERIENCING DIFFICULTIES. If?? at?? any?? time?? you?? are?? experiencing?? difficulties?? performing?? the?? intended?? operation,?? stop?? using?? the?? machine!?? Contact?? our?? Technical?? Support?? Department?? at?? (570)??546-9663.

Additional Safety for Combination Sanders

DISC DIRECTION. Only sand on the downward- moving left side of the sanding disc. Sanding on the upward-moving right side of the sanding disc forces the operator to rely only on hands (rather than the table) for support, which increases the risk of workpiece "kick-out" and impact/abrasion injuries.

AVOIDING ENTANGLEMENT. Becoming entan- gled in the moving parts of this machine can cause pinching and crushing injuries. To avoid these hazards, DO NOT wear loose clothing, gloves, or jewelry, and tie back long hair. Keep all guards in place and secure.

HAND PLACEMENT. Rotating sandpaper can remove a large amount of flesh in a few seconds. Always keep hands away from the sandpaper during operation. Never touch moving sandpaper on purpose.

MINIMUM STOCK DIMENSION. Small workpieces can be aggressively pulled from your hands and present injury hazards. Always use a jig or other holding device when sanding small workpieces, and keep your hands and fingers at least 2" away from the sanding surface.

WORKPIECE SUPPORT. Workpiece kickback can occur with violent force if the workpiece is not properly supported during operation. Always sand with the workpiece firmly against the table or another support device.

SANDING DUST. Sanding creates large amounts of dust and flying chips that can lead to eye injury or respiratory illness. Reduce the risk of these hazards by always wearing approved eye and respiratory protection when using the sander.

WORKPIECE INSPECTION. Nails, staples, knots, or other imperfections in the workpiece can be dislodged and thrown from the sander at a high rate of speed into the operator or bystanders, or cause damage to sandpaper or sander. Never attempt to sand stock that has embedded foreign objects or questionable imperfections.

FEEDING WORKPIECE. Forcefully jamming the workpiece into the sanding surface could cause the workpiece to be aggressively grabbed and pull your hands into the sanding surface. Always firmly grasp the workpiece in both hands and ease it into the sandpaper using light pressure.

SANDPAPER CONDITION. Sandpaper that is worn or damaged not only produces poor sand- ing results, but could fly apart, aggressively grab the workpiece, and throw debris at the operator. Always inspect the sandpaper before operation and replace it if worn or damaged.

IN-RUNNING NIP POINTS. The gap between the moving sandpaper and the fixed table/support creates a pinch point for fingers or workpieces; the larger this gap is, the greater the risk of fingers or workpieces getting caught in it. Minimize this risk by adjusting the table no more than 1???16" away from the sandpaper.

WORKPIECE INTEGRITY. Only sand solid workpieces that can withstand the forces required for power sanding. Make sure the shape of the workpiece can be properly supported on the table; avoid sanding workpieces without flat bot- tom surfaces unless some type of jig is used to maintain support and control when the sanding force is applied.

Like all machinery there is potential danger when operating this machine. Accidents are fre- quently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to decrease the risk of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail- ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocu- tion, fire, or equipment damage, installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards.

Electrocution, fire, or equipment damage may occur if machine is not correctly grounded and connected to the power supply.

Full-Load Current Rating

The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.

The full-load current is not the maximum amount of amps that the machine will draw. If the machine is overloaded, it will draw additional amps beyond the full-load rating.

If the machine is overloaded for a sufficient length of time, damage, overheating, or fire may result??? especially if connected to an undersized circuit. To reduce the risk of these hazards, avoid over- loading the machine during operation and make sure it is connected to a power supply circuit that meets the requirements in the following section.

Model G1183/G1276 (Mfg. Since 3/10)

Circuit Information

A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power sup- ply circuit used for this machine must be sized to safely handle the full-load current drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.)

For your own safety and protection of property, consult a qualified electrician if you are unsure about wiring practices or electrical codes in your area.

Note: The circuit requirements listed in this man- ual apply to a dedicated circuit???where only one machine will be running at a time. If this machine will be connected to a shared circuit where mul- tiple machines will be running at the same time, consult a qualified electrician to ensure that the circuit is properly sized for safe operation.

Circuit Requirements for 110V

This machine is prewired to operate on a 110V power supply circuit that has a verified ground and meets the following requirements:

Circuit Requirements for 220V

This machine can be converted to operate on a

220V power supply (refer to Voltage Conversion instructions). This power supply must have a veri- fied ground and meet the following requirements:

Grounding Requirements

This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current.

For 110V operation: This machine is equipped with a power cord that has an equipment-ground- ing wire and a grounding plug (see following fig- ure). The plug must only be inserted into a match- ing receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.

GROUNDED

5-15 RECEPTACLE

Grounding Prong

5-15 PLUG

Neutral Hot

Figure 6. Typical 5-15 plug and receptacle.

SHOCK HAZARD!

Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided???if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground.

-12-

For 220V operation: The plug specified under

???Circuit Requirements for 220V??? on the previous page has a grounding prong that must be attached to the equipment-grounding wire on the included power cord. The plug must only be inserted into a matching receptacle (see following figure) that is properly installed and grounded in accordance with all local codes and ordinances.

Figure 7. Typical 6-15 plug and receptacle.

Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire. If repair or replacement of the power cord or plug is nec- essary, do not connect the equipment-grounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service per- sonnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, discon- nect it from power, and immediately replace it with a new one.

Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual.

Model G1183/G1276 (Mfg. Since 3/10)

Extension Cords

We do not recommend using an extension cord with this machine. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis.

Extension cords cause voltage drop, which may damage electrical components and shorten motor life. Voltage drop increases as the extension cord size gets longer and the gauge size gets smaller (higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following require- ments:

Model G1183/G1276 (Mfg. Since 3/10)

Voltage Conversion

The voltage conversion MUST be performed by an electrician or qualified service personnel. Make sure the power supply circuit for the new voltage meets the specified circuit requirement on

Page 11.

To convert the machine to 220V:

1.DISCONNECT MACHINE FROM POWER!

2.Replace the 5-15 plug on the power cord with a 6-15 plug.

3.Re-wire the motor as illustrated in the wiring diagram on Page 39.

Note: If the diagram included on the motor conflicts with the one in this manual, the motor may have changed since the manual was printed. Use the diagram provided on the motor.

-13-

SECTION 3: SETUP

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire setup pro- cess!

This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items.

SUFFOCATION HAZARD! Keep children and pets away from plastic bags or packing materials unpacked with this machine. Discard immediately.

-14-

Needed for Setup

The following are needed to complete the setup process, but are not included with your machine.

Unpacking

Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover the machine is damaged, please imme- diately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

Model G1183/G1276 (Mfg. Since 3/10)

Inventory

The following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

Model G1183/G1276 (Mfg. Since 3/10)

D

E

Figure 8. Shipping inventory.

NOTICE

If you cannot find an item on this list, check the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials.

-15-

Cleanup

The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean.

Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.

There are many ways to remove this rust preven- tative, but the following steps work well in a wide variety of situations. Always follow the manufac- turer???s instructions with any cleaning product you use and make sure you work in a well-ventilated area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

???Disposable Rags

???Cleaner/degreaser (WD???40 works well)

???Safety glasses & disposable gloves

???Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1.Put on safety glasses.

2.Coat the rust preventative with a liberal amount of cleaner/degreaser, then let it soak for 5???10 minutes.

3.Wipe off the surfaces. If your cleaner/degreas- er is effective, the rust preventative will wipe off easily. If you have a plastic paint scraper, scrape off as much as you can first, then wipe off the rest with the rag.

4.Repeat Steps 2???3 as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust.

-16-

Gasoline or products with low flash points can explode or cause fire if used to clean machin- ery. Avoid cleaning with these products.

Many cleaning solvents are toxic if concentrat- ed amounts are inhaled. Only work in a well-venti- lated area.

NOTICE

Avoid chlorine-based solvents, such as acetone or brake parts cleaner, that may damage painted surfaces. Test all cleaners in an inconspicuous area before using to make sure they will not damage paint.

Model G1183/G1276 (Mfg. Since 3/10)

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work- piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the main- tenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where your machine is operated is important for safe operation and the longevity of its components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemi- cals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41?????104??F; the relative humidity range exceeds 20???95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

32"

Figure 9. Minimum working clearances.

The base of this machine has holes that accept 5???8" bolts for mounting the machine to a workbench. We strongly recommend that you mount your machine to a workbench to prevent it from moving during operation. An unexpected movement could result in an injury or property damage.

The strongest mounting option is a "Through Mount" where holes are drilled all the way through the workbench, and hex bolts, washers, and hex nuts are used to secure the drill press to the work- bench.

Figure 10. Example of a through mount setup.

Another option for mounting is a "Direct Mount" where the machine is simply secured to the work- bench with a lag screw and flat washer.

Lag Screw

Flat Washer

Machine Base

Workbench

Figure 11. Example of a direct mount setup.

-18-

To assemble the sander:

1.Unthread the screw cap on the sanding belt table lock lever, remove the lever, then unthread the lock bolt and flat washer from the sander (see Figure 12).

Lock Bolt

& Flat Washer

Figure 12. Sanding belt lock lever.

2.Position the belt table trunnion against the side of the belt housing so that the semicircu- lar flange fits into the keyway, then secure the trunnion in place with the lock bolt that was removed in Step 1 (see Figure 13).

Table

Trunnion

Flange

& Keyway

Lock

Bolt

Figure 13. Sanding belt table trunnion installed.

3.Re-install the lock lever onto the lock bolt.

Model G1183/G1276 (Mfg. Since 3/10)

4.Attach the sanding belt table to the trunnion by finger tightening the (3) 5???16"-11 x 1" hex bolts and 5???16" flat washers from underneath the table, as shown in Figure 14. The hex bolts will be fully tightened when aligning the tables in later steps.

x 3

Figure 14. Sanding belt table installed.

5.Attach the 3" dust port to the bottom of the sanding belt housing with the (2) 1???4"- 20 x 1???2" Phillips head screws, as shown in

Figure 15.

x 2

Sanding Belt

Dust Port

Figure 15. Sanding belt dust port attached.

Model G1183/G1276 (Mfg. Since 3/10)

6.Loosen the sanding belt pivot cap screw shown in Figure 16, rotate the sanding belt assembly to the vertical position, then re- tighten the cap screw to hold it place.

Pivot

Cap Screw

Figure 16. Location of the sanding belt pivot cap screw.

7.Attach the dust hose assembly to the lower disc bracket with the (2) #10-24 x 3???8" flange screws, as shown in Figure 17.

x 2

Figure 17. Sanding disc dust hose assembly attached.

-19-

8.Loosen the sanding disc table lock knobs, then move the trunnion brackets away from the lower disc guard, as shown in Figure 18.

Trunnion Bracket

(1 of 2)

Lock

Knob

Figure 18. Lock knob and trunnion bracket positioned to receive the table trunnion.

9.Place the sanding disc table trunnions between the bracket and lower disc guard, then tighten the lock knobs to hold the table in place (see Figure 19).

Table

Trunnion

Figure 19. Sanding disc table trunnion secured by the lock knob.

-20-

Table Gap

Adjustment

To reduce the risk of in-running nip (pinch) points, yet avoid the risk of the sandpaper contacting the tables, the tables should be adjusted away from the sandpaper no more than 1???16".

Note: The procedure for the table gap adjustment is similar for both tables.

To adjust the table-to-sandpaper gap:

1.DISCONNECT SANDER FROM POWER!

2.First, check the existing adjustment by slid- ing the miter gauge into the table T-slot, then positioning a 90?? square flat against the miter face and up against the sanding surface, as shown in Figure 20.

Figure 20. Positioning the miter gauge and square for aligning the table.

???If the square is flat against the miter face and the sanding surface, and the table is no more than 1???16" away from the sandpaper for both tables, no adjustments are need- ed. Fully tighten the hex bolts underneath the table. Continue to the Checking Belt Tracking procedure.

???If the square is not flat against the sanding surface as it remains flat against the miter face, or the table is not at least 1???16" away from the sanding surface, continue with the next step.

Model G1183/G1276 (Mfg. Since 3/10)

-21-

3.Loosen the hex bolts underneath the table that secure it to the trunnion(s).

Note: The sanding belt table has three hex bolts (see Figure 21), and the sanding disc table has two hex bolts on both sides of the table (see Figure 22).

Hex Bolts

Figure 21. Sanding belt trunnion hex bolts.

Hex Bolts

Figure 22. Sanding disc trunnion hex bolts (2 of

4shown).

4.Adjust the table so that when the square is flat against the miter face and the sanding surface at the same time, and that the table is no more than 1???16" away from the sandpaper, then re-tighten the hex bolts.

5. Repeat Step 2 to make sure the table is properly positioned. If necessary, repeat Steps 3???4 until it is.

Model G1183/G1276 (Mfg. Since 3/10)

Checking Belt

Tracking

Proper belt tracking depends on two conditions: 1) The platen height, and 2) the upper roller paral- lelism.

The upper belt roller is designed with a slight crown in the middle, and the belt platen should be even with the highest point of this crown to ensure proper belt tracking.

Additionally, the upper roller should be parallel to the lower roller so that the sanding belt rides evenly in the middle of the rollers.

To check the belt tracking:

1.DISCONNECT SANDER FROM POWER!

2.Put on heavy leather gloves to protect your hands from the abrasive sandpaper

3.Rotate the sandpaper belt down toward the table several times by hand???NOT by pow- er???as fast as possible (see Figure 23).

???If the belt stays centered on the rollers, continue to the Dust Collection procedure on Page 22.

???If the belt begins moving to one side or the other, perform the Tracking Roller &

Platen Adjustment on Page 35 to make sure the belt tracks properly.

Figure 23. Rotating the sanding belt to check belt tracking.

Dust Collection

DO NOT operate the Model G1183/G1276 without an adequate dust collection system. This sander creates substantial amounts of wood dust while operating. Failure to use a dust collection system can result in short and long-term respiratory illness.

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must consider these variables: (1) CFM rating of the dust collector,

(2) hose type and length between the dust col- lector and the machine, (3) number of branches or wyes, and (4) amount of other open lines throughout the system. Explaining how to cal- culate these variables is beyond the scope of this manual. Consult an expert or purchase a good dust collection "how-to" book.

-22-

To connect the sander to the dust collection system:

1.Fit the dust hoses over both dust ports, as shown in Figure 24, and secure them in place with hose clamps.

2.Tug the hoses to make sure they do not come off. Note: A tight fit is necessary for proper performance.

Figure 24. Dust hoses attached.

Model G1183/G1276 (Mfg. Since 3/10)

Power Connection

After you have completed all previous setup instructions and circuit requirements, the machine is ready to be connected to the power supply.

To avoid unexpected startups or property dam- age, use the following steps whenever connecting or disconnecting the machine.

Connecting Power

1.Turn the machine power switch OFF.

2.Insert the power cord plug into a matching power supply receptacle. The machine is now connected to the power source.

Figure 25. Connecting power.

Disconnecting Power

1.Turn the machine power switch OFF.

2.Grasp the molded plug and pull it completely out of the receptacle. Do not pull by the cord as this may damage the wires inside.

Figure 26. Disconnecting power.

Model G1183/G1276 (Mfg. Since 3/10)

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the

Troubleshooting on Page 33.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

Important: When turning the sander ON, if the sanding belt begins to track to one side or the other, immediately turn the machine OFF and disconnect it from power. Then, perform the Tracking Roller & Platen Adjustment procedure on Page 35.

3.Turn the machine ON.

4.Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

???Strange or unusual noises should be inves- tigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

5.Turn the machine OFF.

-23-

SECTION 4: OPERATIONS

Operation Overview

The purpose of this overview is to provide the nov- ice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand.

Due to the generic nature of this overview, it is not intended to be an instructional guide. To learn more about specific operations, read this entire manual and seek additional training from expe- rienced machine operators, and do additional research outside of this manual by reading "how- to" books, trade magazines, or websites.

To reduce the risk of serious injury when using this machine, read and understand this entire manual before operating.

Damage to your eyes and lungs could result from using this machine without proper pro- tective gear. Always wear safety glasses and a respirator when operating this machine.

To complete a typical operation, the operator does the following:

1.Examines the workpiece to make sure it is suitable for sanding.

2.Adjusts the table tilt, if necessary, to the cor- rect angle for the operation.

3.Makes sure the sandpaper is in good condi- tion and properly mounted.

4.Puts on safety glasses and a respirator, and turns the dust collection system ON.

5.Starts the sander.

6.Makes sure the sanding belt is tracking prop- erly.

7.Feeds the workpiece slowly into the sand- paper while maintaining firm pressure on the workpiece against the table or miter gauge. Keeps hands and fingers away from the mov- ing sandpaper.

8.Stops the machine.

NOTICE

If you have never used this type of machine or equipment before, We strongly rec- ommend that you read books, review industry trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

Table Tilt

Angle sanding is performed with the table tilted away from 0?? (perpendicular to the sanding sur- face). Compound angles are sanded using a com- bination of table tilt and miter gauge angle.

Both tables have an adjustable positive stop that is used to quickly return the table to 0??. The belt table has an additional stop at -45?? and uses a flip stop to engage the stops. The disc table has an additional stop at -40?? underneath the table (see

Figures 27???29).

Flip

Stop

Positive

Stops

Figure 27. Sanding belt table tilting controls.

No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- ment, or poor work results.

Figure 28. Sanding disc table tilting controls.

-40?? Positive

Stop

Figure 29. Sanding disc table -40?? positive stop.

Sandpaper Selection

Sanding a workpiece smooth requires using pro- gressively smaller grit sandpaper until the desired finish is attained.

The abrasiveness of sandpaper is designated in grit size???the larger the number, the finer the abrasive and the smaller the scratches. Thus, 100 grit is finer than 60 grit.

Typically, sanding operations start with a coarse grit and progressively work through the finer (larger number) grits until the desired finish is achieved. Avoid skipping a grit to achieve the best results.

Choosing the correct grits involve many factors, such as the workpiece condition, type/hardness, and the desired finish.

There are many types of sanding belts and discs to choose from. We recommend Aluminum Oxide for general workshop environments. Below is a chart that groups abrasives into different classes and shows which grits fall into each class.

To ensure good sanding results, never skip more than 50 grit with each sandpaper change.

-26-

Sanding Belt

Replacement

The Model G1183/G1276 ships with a pre-installed 80-grit, 6" x 48" sanding belt.

1.DISCONNECT SANDER FROM POWER!

2.Loosen the four Phillips head screws that secure the left cover of the sanding belt hous- ing, then remove the cover.

3.Pull the spring-loaded quick-release tension lever forward to lower the top roller, then remove the sanding belt.

Note: Typically, sanding belts have a direc- tion arrow printed on the inside. Match this arrow with the direction arrow label on top of the sanding belt housing (see Figure 30). This will ensure that belt seams are correctly oriented for longer belt life.

Direction Label

Quick-Release

Tension Lever

Figure 30. Replacing sanding belt.

4.While still holding the tension lever down, center the new belt on the top roller, then release the tension lever.

5.Perform the Checking Belt Tracking on

Page 21 to ensure the new belt will track properly during operation.

Model G1183/G1276 (Mfg. Since 3/10)

The Model G1183/G1276 sander ships with a pre- installed 80-grit, 12" diameter adhesive-backed sanding disc.

The sanding disc sticks to the surface of the cast iron disc platen, using the pressure-sensitive adhesive (PSA) backing. The sandpaper can be replaced without removing the table or dust port.

To replace the disc sandpaper:

1.DISCONNECT SANDER FROM POWER!

2.Peel off the old sandpaper, clean the disc surface with mineral spirits, then wipe it dry.

3.Peel back the protective layer on one-half of the sandpaper disc and fold it against the remaining half.

4.Slip the half with the protective layer between the disc and the table edge (see Figure 31 for an example).

Figure 31. Example photo of installing the sandpaper disc.

5.Position the exposed adhesive on the upper half of the aluminum disc that extends above the table. Once it is positioned evenly across the disc, press the adhesive onto the sur- face.

6.Rotate the disc so the lower half is above the table. Peel off the other half of the protective paper, then press the remaining sandpaper against the disc so adhesion is complete.

Model G1183/G1276 (Mfg. Since 3/10)

Only sand on the downward-moving left side of the sanding disc. Sanding on the upward- moving right side of the sanding disc forces the operator to rely only on hands (rather than the table) for support, which increases the risk of workpiece "kick-out" and impact/ abrasion injuries.

Refer to Figures 32???35 for examples of sand- ing operations that are possible with the sanding disc.

Figure 32. Example photo of 90?? disc sanding.

Figure 33. Example of miter sanding.

-27-

Figure 34. Example of compound angle sanding.

Figure 35. Example of round workpiece sanding.

Belt Sanding

The sanding belt removes material faster than the sanding disc, and can be secured at any angle from horizontal to completely vertical with the use of the pivot cap screw shown in Figure 36.

Pivot

Cap Screw

Figure 36. Positioning the sanding belt assembly.

If the sanding belt or table unexpectedly moves when sanding, your hands could slip and contact the moving sandpaper, result- ing in abrasion injuries. Always make sure the table lock lever and the sanding belt pivot cap screw are tight before operation.

Always sand with the workpiece supported by the table. Relying only hands to sup- port the workpiece increases the risk of workpiece "kick-out" and impact/abrasion injuries.

Refer to Figures 37???40 for examples of sanding operations that are possible with the belt sanding assembly.

Figure 37. Sanding workpiece in horizontal position.

Figure 38. Example of end grain sanding.

Model G1183/G1276 (Mfg. Since 3/10)

Figure 39. Example of vertical miter sanding.

Figure 40. Examples of vertical face and edge sanding.

Sanding workpieces with high-resin content or with applied finishes can quickly con- taminate the sandpaper beyond the point where it can be properly cleaned. This will produce poor sanding results. In this case, use a different workpiece, remove the applied finishes, or frequently clean/replace the sandpaper strip.

-29-

SECTION 5: ACCESSORIES

Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine.

6" x 48" Aluminum Oxide Sanding Belts

Our aluminum oxide sanding belts are available in grits from 60???220 and packs of two.

12" PSA Aluminum Oxide Sanding Discs

Our aluminum oxide sanding discs are manufac- tured in ISO 9002 factories to ensure the highest quality and are available in packs of two.

-30-

G2405???Safety Push Blocks

Made of high-impact molded plastic, these safety push blocks have a layer of friction rubber on the bottom that grabs your workpiece as you press down. We strongly recommend these for use with sanders, jointers, router tables, shapers and table saws. Measures 3" x 6".

Figure 41. G2405 Safety Push Blocks.

T20501???Face Shield Crown Protector 4"

T20502???Face Shield Crown Protector 7"

T20503???Face Shield Window

T20452???"Kirova" Anti-Reflective S. Glasses

T20451???"Kirova" Clear Safety Glasses

H0736???Shop Fox?? Safety Glasses

H7194???Bifocal Safety Glasses 1.5

H7195???Bifocal Safety Glasses 2.0

H7196???Bifocal Safety Glasses 2.5

T20503

T20451

Figure 42. Eye protection assortment.

Model G1183/G1276 (Mfg. Since 3/10)

Pro-Stik?? Abrasive Belt Cleaners

G1511???Small: (1???1/2" x 1???1/2" x 8???1/2")

G1512???Large: (2 " x 2" x 12")

Figure 43. Pro-Stik?? Belt Cleaners.

G0710???Wall Hanging Dust Collector

Mount this 1 HP Dust Collector to your wall and keep precious floor space free of clutter. With 450 CFM, this dust collector will handle just about any dust producing machine in your shop. Add a couple of blast gates and a Y fitting and you've got a small dust collection system. A simple mounting bracket allows you to hang this dust collector on the wall, or lift it off to use in a horizontal position on the floor. Very versatile!

Figure 44. G0710 Dust Collector.

Model G1183/G1276 (Mfg. Since 3/10)

H2499???Small Half-Mask Respirator

H3631???Medium Half-Mask Respirator

H3632???Large Half-Mask Respirator

H3635???Cartridge Filter Pair P100

Wood dust has been linked to nasal cancer and severe respiratory illnesses. If you work around dust everyday, a half-mask respirator can be a lifesaver. Also compatible with safety glasses!

Figure 45. Half-mask respirator with disposable cartridge filters.

Heavy-Duty Birch Workbench

H8361???60" x 30"

H8362???72" x 36"

Sized to fit the needs of any shop, these Super Heavy-Duty Birch Workbenches have solid 3" thick tops. The solid wood end vise measures 14???3???4" wide (H8361) or 17???3???4" (H8362) and has a 7" maximum capacity. Stable laminated birch pro- vides strength and durability.

Figure 46. H8362 Super Heavy-Duty Birch

Workbench.

-31-

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Before & During Operation:

???Loose mounting bolts.

???Damaged, excessively worn, or clogged sandpaper.

???Worn or damaged switch or wires.

???Excessive dust build-up.

???Efficiency of the dust collection system.

???Any other unsafe condition.

Lubrication

All bearings on the sander are permanently lubri- cated and sealed, and they need no further atten- tion unless they require replacement.

-32-

Cleaning &

Protecting Machine

Cleaning the Model G1183/G1276 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.

Protect the unpainted cast iron surfaces on the table by wiping the table clean after every use??? this ensures moisture from wood dust does not remain on bare metal surfaces. Then apply a non- staining rust preventative that does not contain silicone or oil.

Cleaning Sandpaper

When the sandpaper surface becomes clogged with resin or gummy sawdust, the efficiency of the sanding operation is significantly reduced and can leave glazed or gouge marks in the workpiece.

Regularly clean the belt and disc sandpaper by using crepe-rubber cleaners (see Accessories on Page 31 for options from Grizzly).

Model G1183/G1276 (Mfg. Since 3/10)

SECTION 7: SERVICE

Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663.

Troubleshooting

Tracking Roller &

Platen Adjustment

To ensure proper belt tracking, the belt platen must be even with the upper roller crown and the upper and lower rollers must be parallel.

To adjust the roller and platen:

1.DISCONNECT SANDER FROM POWER!

1.Remove the side cover and table from the belt assembly.

2.Pull the quick-release tension lever down, then remove the sanding belt, as shown in

Figure 47.

Quick-Release

Tension Lever

Figure 47. Removing the sanding belt.

3.If the sanding belt assembly is not already horizontal, loosen the cap screw shown in Figure 48 and lower the assembly to the horizontal position.

Loosen this pivot cap screw.

Figure 48. Location of the cap screw that secures the rotation of the belt assembly.

Model G1183/G1276 (Mfg. Since 3/10)

4.Place the straightedge over the platen and upper roller aligned with the middle of the roller (the crown at the highest point), as shown in Figure 49.

Figure 49. Comparing the platen height with the upper roller crown.

???If the platen is not even with or is higher than the upper roller crown, loosen the platen cap screw shown in Figure 49, adjust the platen even with the middle of the top roller, then re-tighten the cap screw to secure the platen in place.

5.Replace the sanding belt, put on gloves to protect your hands, then rotate it several times by hand???NOT by power.

???If the sanding belt tracks steadily in the middle of the rollers without moving to one side or the other, no other adjustments are necessary. Continue to Step 11.

???If the sanding belt does track to one side or the other, continue with next step.

-35-

6.Fully loosen the locking thumb wheels on both of the roller adjustment screws shown in

Figure 50.

Adjustment Screws

& Locking Thumb Wheels

Figure 50. Upper roller adjustment screws and locking thumb wheels.

7.Back out the adjustment screws so that they are not against the belt housing.

Note: The next step is matter of trial-and- error until you attain proper belt tracking. The adjustment screws control the tilt of the upper roller to make it parallel with the lower roller, which affects the belt tracking.

-36-

8.Make small changes to the adjustment knobs as you continue to rotate the sanding belt by hand.

9.When the sanding belt continues to track in one position on the rollers, make sure both adjustment screws are making contact with the belt housing, then re-tighten the locking thumb screws.

10.Repeat Step 4 to make sure the platen is still even with the crown of the upper roller.

11.Replace the side cover and table to the belt assembly before connecting the sander to power.

12.When first connecting the sander to power after this, turn it ON and watch the belt track- ing closely.

???If the sanding belt begins to track to one side or the other, immediately turn the machine OFF and disconnect it from power. Then, repeat this procedure until the belt tracks properly.

Model G1183/G1276 (Mfg. Since 3/10)

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang- es to the electrical systems of future machines. Study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is con- nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical com- ponents!

MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpre- dictable results, including serious injury or fire. This includes the installation of unapproved after- market parts.

WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires dis- connected or connected during any wiring task to ensure tight connections.

CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of this man- ual when connecting your machine to a power source.

WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious per- sonal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components.

MOTOR WIRING. The motor wiring shown in these diagrams is current at the time of printing but may not match your machine. If you find this to be the case, use the wiring diagram inside the motor junction box.

CAPACITORS/INVERTERS. Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

EXPERIENCING DIFFICULTIES. If you are expe- riencing difficulties understanding the information included in this section, contact our Technical Support at (570) 546-9663.

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

110V Wiring Diagram

Figure 51. Switch and motor wiring.

A1 A2 A3

B1 B2 B3

Motor (viewed from bottom)

110VAC NEMA 5-15

(As Recommended)

Ground

220V Wiring Diagram

Motor (viewed from bottom)

Ground

Run Capactitor

25M 350V

Start Capactitor

200M 250V

Hot

Ground

G

3/10) Since .(Mfg G1183/G1276 Model

22

20

19

21

105 107

18

11

16

17 1

118

9 8 7V2-1

137 127

126

111

4

2

3 100

103 102110

PARTS 9: SECTION

Main Parts List

Main Parts List

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

CUT ALONG DOTTED LINE

WARRANTY CARD

Name_____________________________________________________________________________

Street_____________________________________________________________________________

City _______________________ State_________________________ Zip _____________________

Phone # ____________________ Email ________________________ Invoice #_________________

Model # ____________________ Order #_______________________ Serial #__________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

1.How did you learn about us?

2.Which of the following magazines do you subscribe to?

3.What is your annual household income?

4.What is your age group?

5.How long have you been a woodworker/metalworker?

6.How many of your machines or tools are Grizzly?

9.Would you allow us to use your name as a reference for Grizzly customers in your area?

10. Comments: _____________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

WARRANTY AND RETURNS

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly???s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly???s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a ???Return Number,?????? which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

Buy Direct and Save with Grizzly?? ??? Trusted, Proven and a Great Value!

~Since 1983~

Visit Our Website Today For

Current Specials!

ORDER

24 HOURS A DAY!

1-800-523-4777