2010) (July 297298800

WARNING

Please read all instructions before using this freezer.

For Your Safety

???DO NOT store or use gasoline, or other ???ammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding ???ammability and other hazards.

???DO NOT operate the freezer in the presence of explosive fumes.

???Remove all staples from the carton. Staples can cause severe cuts, and also destroy ???nishes if they come in contact with other appliances or furniture.

De???nitions

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Installation Checklist

Doors

???Handles are secure and tight

???Door seals completely to cabinet on all sides

???Freezer door is level across the top

Leveling

???Freezer is level, side-to-side and tilted 1/4??? (6mm) front-to-back

???Kick plate is properly attached to freezer

???Cabinet is setting solid on all corners

Electrical Power

???House power turned on

???Freezer plugged in

Ice Maker

???House water supply connected to freezer

???No water leaks present at all connections - recheck in 24 hours

???Ice maker is turned ON

???Front ???lter must be ???ush with ???lter housing (select models)

Final Checks

???Shipping material removed

???Freezer temperatures set

???Registration card sent in

Child Safety

Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the freezer is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.

Proper Disposal of your Freezer

Risk of child entrapment

Child entrapment and suffocation are not problems of the past. Junked or abandoned freezers or freezers are still dangerous ??? even if they will sit for ???just a few days???. If you are getting rid of your old freezer or freezer, please follow the instructions below to help prevent accidents.

Proper Disposal of Refrigerators/Freezers

We strongly encourage responsible appliance recycling/ disposal methods. Check with your utility company or visit www.recyclemyoldfridge.com for more information on recycling your old freezer.

Before you throw away your old refrigerator/ freezer:

??? Remove doors.

??? Leave shelves in place so children may not easily climb inside.

??? Have refrigerant removed by a quali???ed service technician.

WARNING

These guidelines must be followed to ensure that safety mechanisms in this freezer will operate properly.

Electrical Information

???The freezer must be plugged into its own dedicated 115 Volt, 60 Hz., 15 Amp, AC only electrical outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must

be installed in accordance with local codes and ordinances. Consult a quali???ed electrician. Avoid connecting freezer to a Ground Fault Interrupter (GFI) circuit. Do not use an extension cord or adapter plug.

???If the power cord is damaged, it should be replaced by an authorized service technician to prevent any risk.

???Never unplug the freezer by pulling on the power cord. Always grip the plug ???rmly, and pull straight out from the receptacle to prevent damaging the power cord.

???Unplug the freezer before cleaning and before replacing a light bulb to avoid electrical shock.

???Performance may be affected if the voltage varies by 10% or more. Operating the freezer with insuf???cient power can damage the compressor. Such damage is not covered under your warranty.

???Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the freezer from being turned off accidentally.

IMPORTANT

To disconnect power to the unit, unplug the unit or switch the breaker that supplies power to the unit to the off position.

Required Tools

You will need the following tools:

This Use & Care Guide provides general operating instructions for your model. Use the freezer only as instructed in this Use & Care Guide. Before starting the freezer, follow these important ???rst steps.

Location

???Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.

???If possible, place the freezer out of direct sunlight and away from the range, dishwasher or other heat sources.

???The freezer must be installed on a ???oor that is level and strong enough to support a fully loaded freezer.

???Consider water supply availability for models equipped with an automatic ice maker. If you do not hook up water to the freezer, remember to turn the ice maker off.

CAUTION

DO NOT install the freezer where the temperature will drop below 55??F (13??C) or rise above 110??F (43??C). The compressor will not be able to maintain proper temperatures inside the freezer.

DO NOT block the kick plate on the lower front of your freezer. Suf???cient air circulation is essential for the proper operation of your freezer.

???NOTE

The exterior walls of the freezer may become quite warm as the compressor works to transfer heat from the inside. Temperatures as much as 30??F warmer than room temperature can be expected.

INSTALLATION

Installation

Installation clearances:

???Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:

Sides - 3/8 inch

Top and Back - 1 inch

???Allow for trim kit if it to be installed with the unit.

???NOTE

If your freezer is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.

Freezer

3/8??? (10mm)

???NOTE

All set screws should be tightened and sub-???ush (Allen set screw should be seated just below the surface of the end cap) of handle end cap. The end caps should be drawn tight to freezer door with no gaps.

Kick Plate Removal

To remove the kick plate, use a Phillips head screwdriver and remove the two screws holding the kick plate to the cabinet. Then pull the kick plate away from the unit.

Matching Freezer and Freezer Door Handle

Installation

Leveling

???The freezer must have all bottom corners resting ???rmly on a solid ???oor.

???The ???oor must be strong enough to support a fully loaded freezer.

???It is VERY IMPORTANT for your freezer to be level in order to function properly. If the freezer is not leveled during installation, the door may be misaligned and not close or seal properly, causing cooling, frost or moisture problems.

Leveling instructions continued on next page.

Remove Screws

Kick Plate Removal

To Level The Freezer:

While unit is lying on its back for wood skid removal, note the location of the four (4) leg levelers installed at each corner. These leg levelers will be used to level the freezer and to adjust the height. Use a carpenter???s level to level the freezer from front to back and side to side.

???NOTE

Make sure to allow for the Trim and Leveling Kit if it is to be installed with the unit.

Level Front to Back & Side to Side

Leveling Instructions For Matching Ta ll Freezer / Tall Freezer Pair:

???Level door of ???rst unit using all four levelers and slide unit into place. Recheck for levelness and adjust if necessary.

???Measure distance from ???oor to bottom of door on ???rst unit. Adjust and level second unit so door height matches.

???Leg Level Adjustments:

???One full turn of all four leg levelers will raise door 5/32???.

LEVELING INSTRUCTIONS

???Slide second unit into place leaving a minimum

gap of 3/16??? between units for door swing clearance.

???This last step may require at least one extraction of the second unit to properly align units in a ???built-in??? application.

Leveling Door with Adjustable Hinge

Use the lower hinge adjustment to ???ne tune the door height and for ???nal cabinet spacing. Use a 7/16??? socket or wrench to adjust the screw at the bottom of the lower hinge.

Adjusting Doors For Matching Tall

Refrigerator / Tall Freezer Pair

The doors may also be adjusted side to side with the slotted hinge for aligning the doors parallel to each other. Loosen the two bolts with a 3/8??? wrench and one screw with a Phillips screwdriver. Shift the doors until parallel, then retighten the screws securely. (See illustration below.)

Lower Hinge Adjustment For Leveling The Doors Of The Matching Tall Refrigerator / Tall Freezer Pair

To level the doors using the adjustable lower hinge (some models):

1.If the freezer door is lower than the freezer door, raise the freezer door by turning the adjustment screw clockwise using a 7/16 inch socket wrench. (See illustration below.)

2.If the freezer door is lower than the freezer door, raise the freezer door by turning the adjustment screw clockwise using a 7/16 inch socket wrench. (See illustration below.)

Slotted Hinge

Adjustment

3/8??? Bolts

Screw

DOOR REMOVAL

If door must be removed:

???Unplug the unit or switch the breaker that supplies power to the unit to the off position.

???Remove the plastic top hinge cover.

???Hold the door in place while removing the top hinge from the cabinet.

???Remove the two 3/8??? hex head bolts from the top hinge with a 3/8??? wrench or socket.

???Lift the door upwards and pull up and away from the cabinet until free of the bottom hinge pin mounted on the front of the cabinet.

???To replace the door, reverse the above procedures and securely tighten all screws to prevent hinge slippage.

CAUTION

Doors are heavy. It is recommended to have two people to remove or replace the door assembly from the cabinet.

PRO-SELECT??? ELECTRONIC CONTROL

FEATURES

Replace Air Filter

When the ???REPLACE AIR FILTER??? LED is illuminated yellow, the air ???lter needs to be replaced. The control will signal for air ???lter replacement after 3600 hours of freezer operation. After replacing the air ???lter, reset the air ???lter timer by pressing the AIR FILTER key for 3 seconds. The ???REPLACE AIR FILTER??? LED will be illuminated green for three (3) seconds, con???rming a timer reset.

??F

Resetting Air Filter Alarm

Power Fail

The POWER FAIL indicator light informs you that due to a power failure the cabinet temperature exceeded 23??F (-5??C). If the power failure lasted more than one

(1) hour the display alternates between showing the power failure duration (Hours and DURATION LED illuminate in the display) and the cabinet temperature (??F or ??C illuminates) every ?? second. This safety feature will aid in determining what food spoilage action to take.

The Power Fail indicator light and duration display can be turned off by pressing the Alarm Off Key.

??F

Power Fail Indicator

WATER SUPPLY

WARNING

To avoid electric shock, which can cause death or severe personal injury, disconnect the freezer from electrical power before connecting a water supply line to the freezer.

CAUTION

To Connect Water Supply Line To Ice Maker Inlet

Valve

1.Disconnect refrigerator from electric power source.

2.Place end of water supply line into sink or bucket. Turn ON water supply and ???ush supply line until water is clear. Turn OFF water supply at shutoff valve.

3.Remove plastic cap from water valve inlet and discard cap.

4.If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (?? inch / 6.4 mm). Slide ferrule (sleeve) into valve inlet and ???nger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure A.

???NOTE

Plastic Water Tubing

to Ice Maker

Fill Tube

Include enough tubing in loop to allowmoving freezer out for cleaning.

Steel

Clamp

Brass

Compression

Clamp

Ferrule

(Sleeve)

Copper

Waterline

Water Valve

Bracket

Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will

Need:

???Basic Tools: adjustable wrench, ???at-blade screwdriver, and PhillipsTM screwdriver

???Access to a household cold water line with water pressure between 30 and 100 psi.

???A water supply line made of ?? inch (6.4 mm) OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the freezer to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the freezer can be moved out for cleaning (as shown).

???A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

???A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.

Valve Inlet

Water Valve

Copper Water Line

From Household Water Supply

Figure A. Copper Water Line Connection

If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and ???nger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

See Figure B.

Stainless

Steel

Waterline

Water Valve

Bracket

Valve Inlet

Water Valve

6 ft. Stainless Steel Water Line From Household Water Supply

Figure B. Stainless Steel Water Line Connection

5.With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of freezer as shown.

6.Coil excess water supply line (copper tubing only), about 2?? turns, behind freezer as shown and arrange coils so they do not vibrate or wear against any other surface.

7.Turn ON water supply at shutoff valve and tighten any connections that leak.

8.Reconnect freezer to electrical power source.

9.To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker???s On/Off power switch to the ???I??? position (rear mounted).

???NOTE

Check with your local building authority for recommendations on water lines and associated materials prior to installing your new freezer. Depending on your local/state building codes, Frigidaire recommends for homes with existing valves its Smart Choice?? water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice?? water line kit 5305510264 (with a 20 ft. Copper Water Line with selftapping saddle valve). Please refer to http://frigidaire.stores.yahoo.net for more information.

ICE SERVICE

ICE SERVICE

If your freezer has an automatic icemaker, it will provide a suf???cient supply of ice for normal use. During the initial startup of your freezer, however, no ice will be produced during the ???rst 24 hours of operation.

Automatic ice makers are also optional accessories that may be installed in some models at any time. Call your local dealer for information.

Turning Your Ice Maker On

After the plumbing connections have been completed, the water supply valve must be opened. Place the ice container under the ice maker, pushing it as far back as possible. Lower the wire signal arm to its ???down??? or ON position. New plumbing connections may cause the ???rst production of ice cubes to be discolored or have an odd ???avor. These ???rst cubes should be discarded until the cubes produced are free of discoloration and taste.

Turning Your Ice Maker Off

To stop the ice maker, lift the wire signal arm until it clicks and locks in the ???up??? or OFF position. The ice maker also turns off automatically when the ice container is full. If your model has an adjustable freezer shelf, place the shelf in the lower position, so that the wire signal arm will hit the ice when the container is full.

Ice Maker Tips

???If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.

???Ice cubes stored too long may develop an odd ???avor. Empty the ice container and ensure that the wire signal arm is in its ???down??? or ON position. The ice maker will then produce more ice.

???Occasionally shake the ice container to keep ice separated.

???Keep the wire signal arm in its ???up??? or OFF position until the freezer is connected to the water supply or whenever the water supply is turned off.

???The following sounds are normal when the ice maker is operating:

???Motor running

???Ice loosening from tray

???Ice dropping into ice container

???Running water

???Water valve opening or closing

13

Ice Service

Leveling Bracket

Ice

Container

1??? or less

IMPORTANT

Your ice maker is shipped with the wire signal arm in the ON position. To ensure proper function of your ice maker, hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position.

Check the leveling bracket on the ice maker to ensure the ice maker is level. If the gap between the freezer wall and the ice maker is the same at top and bottom, then ice maker is level. If the ice maker is not level, loosen the screw and slide the bracket to the correct position to make it level. Retighten the screw. You will need a 1/4 inch socket wrench for this task.

CAUTION

???DO NOT place the ice container in dishwasher.

???Wash the ice container in warm water with mild detergent. Rinse well and dry.

???Stop the ice maker when cleaning the freezer and during vacations.

INTERIOR LIGHTING

The mid level and upper level lighting comes on automatically when the door is opened.

To replace the light bulbs:

IMPORTANT

To disconnect power to the unit, unplug the unit or switch the breaker that supplies power to the unit to the off position. Replace the old bulb with a bulb of the same wattage.

1.To replace the light bulb, turn the temperature control to OFF and unplug the electrical cord.

2.Remove the lens from the lamp housing by unsnapping it from the lamp housing using your ???ngers or a screwdriver. Be careful not to break the locking tabs on the lamp housing.

3.Replace the old bulb with a bulb of the same type and wattage.

4.To replace the lens, snap one side of the lens opening to the tab on the lamp housing. Then carefully attach the other side.

Mid Level Lighting Light Bulb Removal

The upper level lighting comes on automatically when the door is opened.

To replace the light bulbs:

IMPORTANT

To disconnect power to the unit, unplug the unit or switch the breaker that supplies power to the unit to the off position. Replace the old bulb with a bulb of the same wattage.

1.To replace the light bulb, turn the temperature control to OFF and unplug the electrical cord.

2.Remove the light shield by pushing in on the sides where the two tabs are located in the back, then rotate the light shield down and out.

3.Replace the old bulb with a bulb of the same type and wattage.

4.When replacing the light shield, insert the three tabs in the front of the light shield into the slots in the control box and then rotate the rear upward until the two retaining latches lock into place.

Light Shield

Light Shield Tabs

STORAGE

SpaceWise??? Glass Shelves

Multi-position adjustable slide out glass shelves can be moved to any position for larger or smaller packages. The shipping spacers that stabilize the shelves for shipping may be removed and discarded.

To Adjust The Shelves

???Lift front edge up.

???Pull shelf out.

???Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf into the desired slots and lock into position.

Insert Into

Slots

STORAGE AND CLEANING

IDEAS FOR STORING FOODS

Fresh Food Storage

???Keep the fresh food compartment between 34?? F and 40?? F with an optimum temperature of 37?? F.

???Avoid overcrowding the freezer shelves, which reduces air circulation and causes uneven cooling.

Fruits and Vegetables

???Store fruits and vegetables in crisper drawers, where trapped moisture helps preserve food quality for longer time periods.

Meat

???Wrap raw meat and poultry securely so leakage and contamination of other foods or surfaces does not occur.

ENERGY SAVING IDEAS

???Locate the freezer in the coolest part of the room, out of direct sunlight, and away from heating ducts or registers. Do not place the freezer next to heat- producing appliances such as a range, oven, or dishwasher. If this is not possible,

a section of cabinetry or an added layer of insulation between the two appliances will help the freezer operate more ef???ciently.

???Level freezer so that the door closes tightly.

???Refer to the ???SETTING THE TEMPERATURE CONTROL??? section for the suggested temperature control settings.

???Do not overcrowd the freezer or block cold air vents. Doing so causes the freezer to run longer and use more energy.

???Cover foods and wipe containers dry before placing them in the freezer. This cuts down on moisture build-up inside the unit.

???Organize the freezer to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.

VACATION AND MOVING TIPS

Short Vacations:

???Leave the freezer operating during vacations of less than three weeks.

Long Vacations:

If the freezer will not be used for several months:

???Remove all food and unplug the power cord.

???Clean and dry the interior thoroughly.

???Leave the freezer door open slightly, blocking it open if necessary, to prevent odor and mold growth.

Moving: When moving the freezer, follow these guidelines to prevent damage:

???Disconnect the power cord plug from the wall outlet.

???Remove foods, then defrost, and clean the freezer.

???Secure all loose items such as base panel, baskets, and shelves by taping them securely in place to prevent damage.

???In the moving vehicle, secure freezer in an upright position to prevent movement. Also protect outside of freezer with a blanket, or similar item.

CARE & CLEANING

Keep your freezer clean to prevent odor build-up. Wipe up any spills immediately and clean at least twice a year. Never use metallic scouring pads,

brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not wash any removable parts in a dishwasher. Always unplug the electrical power.

CAUTION

???When moving the freezer, pull straight out. Do not shift the freezer from side to side as this may tear or gouge the ???oor covering.

???Damp objects stick to cold metal surfaces. Do not touch interior metal surfaces with wet or damp hands.

Interior freezer temperature is too warm.

Sound And Noise

Louder sound levels * Modern freezers have increased whenever freezer is storage capacity and more stable on.temperatures. They require heavy

duty compressors.

*This is normal. When the surrounding noise level is low, you might hear the compressor running while it cools the interior.

*This is normal. Sound will level off or disappear as freezer continues to run.

* Floor is uneven or weak.

*Ensure ???oor can adequately support freezer. Level the freezer by putting wood or metal shims under part of the freezer.

* Freezer is touching the wall.

*Re-level freezer or move freezer slightly. Refer to ???LEVELING??? in the ???FIRST STEPS??? section.

Odors in freezer. * Interior needs to be cleaned.

*Foods with strong odors are in the freezer.

*Clean interior with sponge, warm water, and baking soda. Replace air ???lter.

*Cover the food tightly.

Light bulb is not on. * The light bulb is burned out.

*No electric current is reaching the freezer.

*Control is in Sabbath mode (Sb is displayed on control)

*Follow directions under ???INTERIOR LIGHTING??? section.

*See ???Freezer DOES NOT RUN???.

*Depress TEMP MODE key and CONTROL LOCK key for 3 seconds.