WARNING

To avoid serious injury:

???Adult supervision is required.

???Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pool areas or other bodies of water.

???Always wear shoes or sneakers.

???Never allow more than one rider.

Note: Some parts are assembled on both sides of the vehicle.

Headlight

Cover

Cap

Frame

Fork

2 Fork Covers

Pedal Axle

Pedal

4 Pedal Hubs

Front Wheel

CAUTION

This product contains small parts in its unassembled state.

Adult assembly is required.

IMPORTANT!

???Please save all packaging material until assembly is complete to ensure that no parts are discarded.

???Please wipe each part with a clean, dry cloth before assembly.

???Some parts shown are assembled to both sides of the trike.

Note: Tighten and loosen screws with a Phillips screwdriver. Do not over-tighten the screws.

#8 x 3" Screw ??? 1

FASTENERS ACTUAL SIZE

Handlebar

Seat

Seat Retainer

Straight Axle

2 Covers

2 Rear Wheels

2 Hubcaps

Part Not Shown: Label Sheet

Rear Wheel

(Indented Side Down)

Hubcap

Hubcap

(Peg Side Down)

Straight Axle

Hubcap

1

(Peg Side Up)

Straight Axle

???Slide a hubcap (peg side up) onto the straight axle.

???Slide a rear wheel (indented side down) onto the straight axle.

Frame

???Turn the frame on its side with the exposed end of the straight axle up.

???Place the cap nut assembly tool under the assembled rear wheel and onto the cap nut.

???Slide a rear wheel (indented side up) onto the end of the straight axle.

???Slide a hubcap (peg side down) onto the straight axle.

???Place a cap nut on the end of the straight axle. Tap the cap nut with a hammer. Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle.

???Insert one of the tabs on a cover into a slot in the hubcap. Push to snap the cover into place. Repeat this procedure to attach the other cover to the other hubcap.

Pedal Hub

Pedal Axle

Tab

Straight Axle

2

BOTTOM VIEW

???Turn the frame upside down.

???Insert the straight axle through the holes in the rear of the frame.

Tab

Slot

Pedal Hub

4

???Fit two pedal hubs onto the pedal axle tabs. Make sure the tabs fit into the slot in each pedal hub.

Pedal Hubs

Pedal Axle

Front Wheel

Hole

5

???While holding the pedal hubs on the pedal axle, insert the

pedal axle through the hole in the center of the front wheel.

???Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel.

Pedal Hub

Pedal Hub

Pedal

Pedal Axle

Scrap Block of Wood

7

???Fit the pedal on the pedal axle. Tap the pedal with a hammer until it is secure.

???Pull the pedal up to be sure it is secure. If you can remove it, you have not secured it properly. Tap it with the hammer again.

Fork Arms

Fork Cover

6

8

Groove

Pedal Axle

???Turn the front wheel assembly over.

???Insert the remaining pedal hubs on top of and below the pedal axle and into the hole in the center of the front wheel.

???Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel.

???Place the front wheel assembly between the fork arms. Make sure the pedal axle fits into the groove at the bottom of each fork arm.

???Place a fork cover over the pedal axle on one fork arm.

???Insert two #8 x 3/4" screws into the fork cover and tighten.

???Repeat this procedure to attach the other fork cover to the other fork arm.

???Insert the fork post up through the hole in the neck of the frame. Make sure the fork is positioned so that the fork covers face the rear wheels.

???Place the handlebar onto the fork post and push it down onto the frame. Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post.

Hint: You may need to rotate the handlebar to align the holes.

???Insert the #8 x 3" screw through the hole in the handlebar and into the fork post so that part of the screw (about 3/4") is still visible. Tighten the screw.

Cap

10

??? Insert and ???snap??? the cap into the hole in the frame.

???Fit the tab on the headlight cover to the slot in the top of the handlebar.

???Insert two #8 x 3/4" screws into the headlight cover. Tighten the screws.

Seat Retainer

Seat

Peg

Holes

12

???Position the seat upside down.

???Fit the small pegs on the seat retainer into the holes in the seat.

Label Decoration

Attaching the Seat

11

9

8

(Place remaining label 8???s on opposite side of front wheel)

10

(Place label 7 on opposite side)

6(Place label 15

on opposite side)

16

12

(Place label 13 on opposite side)

14

5

Helpful Hint: The seat can be attached to the frame in any of three positions, depending on the size of your child. Check your child???s fit on the trike by observing the seat to pedal distance, as it is being ridden. If the pedals seem too far away or too close for your child, move the seat up or down.

Seat

Retainer

Slots

???At an angle, insert the tabs on the seat into any of the top three sets of slots for the lower, middle or upper position.

???Lower the seat so that the seat retainer inserts and snaps into the slots in the frame.

???Pull up on the seat to be sure it is secure.

Battery Replacement

Note: For best performance, we recommend replacing the batteries that came with this trike with three, new alkaline "AA" (LR6) batteries.

Headlight Cover

1

???Loosen and remove the two screws from the headlight cover. Remove the headlight cover.

Battery Compartment

2

1.5V x 3 ???AA??? (LR6)

Hint: When sound or lights become faint or stop, it's time for an adult to replace the batteries. We recommend the use of alkaline batteries for longer battery life.

???Loosen the screw in the battery compartment door. Open the battery compartment door.

???Insert three "AA" (LR6) alkaline batteries.

???Close the battery compartment door and tighten the screw.

???Replace the headlight cover. Replace the screws and tighten.

???Protect the environment by not disposing of this product with household waste (2002/96/EC). Check

your local authority for recycling advice and facilities (Europe only).

Battery Safety Information

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

???Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

???Insert batteries as indicated inside the battery compartment.

???Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire.

The batteries inside may explode or leak.

???Never short-circuit the battery terminals.

???Use only batteries of the same or equivalent type, as recommended.

???Do not charge non-rechargeable batteries.

???Remove rechargeable batteries from the product before charging.

???If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Care

???Check the plastic parts regularly and if broken or cracked, dispose of them properly.

???Check all fasteners regularly to be sure they are tight. If the fasteners are not tight, tighten them as necessary.

???To clean, use a mild soap and water solution and a clean cloth. Rinse clean with water to remove soap residue.

FCC Statement

United States Only

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user???s authority to operate the equipment.

Removing the Seat

Seat

Seat Retainer Tab

Frame

Seat Retainer Tab

???Turn the frame on its side.

???Squeeze the seat retainer tabs toward one another and lift the seat from the frame.

Consumer Information

IMPORTANT! It is good practice to start training children very young regarding the importance of helmet use. When children are older and riding bicycles and faster vehicles, it is important that they use a helmet each and every time they ride. For this reason, even while riding a tricycle, it is

a good idea to familiarize your child with helmet use, so that it becomes a habit for life. Choose a helmet that complies with requirements of the applicable certifying agency for bicycle helmets.