L
E
A
R
N
I
N
G
P
A
T
T
E
R
N
S
???
Model Number: G5911
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
Please keep this instruction sheet, as it contains important information.
Use the upright position only when your child has developed enough upper body control to sit without leaning forward.
Warning
WARNING
To prevent serious injury or death:
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly. The kickstand is packaged within the pad at the factory. Before beginning assembly, please remove kickstand from the pad.
???It is dangerous to use this product on an elevated surface.
???Never use on a soft surface (bed, sofa, cushion) since product can tip over and cause suffocation in soft surfaces.
???Always use the restraint until child is able to climb in and out of the chair unassisted.
???Never leave child unattended.
???Use the upright position only when child has developed enough upper body control to sit without
leaning forward.
???Never use as a carrier or lift while child is seated. Never use the toy bar as a handle.
???Reclined position not recommended for children who can sit up by themselves (6 months approximately, until 9 kg).
Consumer Information
Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts.
Great Britain: telephone 01628 500302.
Toy Bar
3 Toys 
Seat Back
Tube
2 Retainers with Lock Nut
Kickstand
Cross Brace
Pad
Front Tube
2 Side 
Rails
2
Assembly
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
CAUTION
This package contains small parts in its unassembled state. Adult assembly is required.
2 Side
Rails
#8 x 1.9 cm (3/4") Screw
Shown Actual Size
Cross
Brace
???Position each side rail so that the button faces outward.
???Fit the cross brace between the side rails, as shown.
???Push the cross brace down to ???snap??? it into place. This may require a lot of force.
3
??? Insert the seat back tube into the socket in each side rail.
??? While pressing the tabs on the ends of the seat back tube, continue to insert the seat back tube into the sockets in each side rail, until the tabs ???snap??? into place. Make sure you hear a ???snap??? on each side.
??? Pull the seat back tube up to be sure it is secure in the side rail sockets.
3
Assembly
Side Rail
Hole
Front Tube
Vibrations
4 UnitSide Rail
Hole
???Locate the hole in each side rail.
???With the vibrations unit facing forward, fit the front tube to the side rails, as shown. Hold the front tube in place and proceed to step 5.
Side
Rail
Side
Rail
Front Tube
5
IMPORTANT! Please follow the next assembly (step 6) carefully to completely secure the front tube to the side rails.
4
Assembly
6
???Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail.
Retainer with Lock Nut
Rounded Side
M4 Lock Nut - 2
(Inside Retainer)
Shown Actual Size
Kickstand
Hint: A lock nut has been factory assembled to the retainer. During shipment, the lock nut may have fallen out of the retainer. If it has, please fit it into the hexagonal hole in the retainer so that the rounded side of the lock nut faces out.
???Tighten the screw with a Phillips screwdriver. Do not
???Repeat this procedure to fasten the screw in the other end of the front tube and side rail, using the remaining retainer with lock nut.
5
Assembly
Pad
Pad Slot
Seat Back
Tube
8
??? Turn the assembly upright.
??? Fit the upper pocket on the pad onto the seat back tube.
??? Fasten the pad buckles around each side rail.
Side
Rail
Pad
Buckles
Hardboard
9
??? Turn the hardboard over and insert it into
the slot in the front edge of the pad.
??? Fasten the pad buckles on the front edge of the pad
and underneath the seat. Make sure you hear a ???snap??? on both sides.
??? Press the fasteners together in the seat back portion of the pad.
Assembly is now complete.
6
Battery
Compartment
???Locate the battery compartment on the bottom of the vibrations unit.
???Loosen the screw in the battery compartment door with a Phillips screwdriver.
???Lift to remove the battery compartment door.
???Insert one LR20 "D" alkaline battery as indicated inside the battery compartment.
Hint: We recommend using an alkaline battery for longer battery life.
???Replace the battery compartment door and tighten the screw with a Phillips screwdriver. Do not
Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
???Do not mix old and new batteries or batteries of different types: alkaline, standard
???Insert batteries as indicated inside the battery compartment.
???Remove batteries during long periods of
???Never
???Use only batteries of the same or equivalent type, as recommended.
???Do not charge
???Remove rechargeable batteries from the product before charging.
???If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
7
IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
WARNING
To prevent serious injury or death:
Use the upright position only when child has developed enough upper body control to sit without leaning forward.
Seat Position
WARNING
To prevent serious injury or death:
???Always use the restraint until child is able to climb in and out of the chair unassisted.
???It is dangerous to use this product on an elevated surface.
???Never leave child unattended.
1
Select a seat position for your child???s comfort: Upright or Recline.
Upright
While pressing the button on each side rail, lift the seat back.
Recline
While pressing the button on each side rail, lower the seat back.
Restraint
Pad
2
???Place your child in the seat. Position the restraint pad between your child???s legs.
???Fasten the restraint belts to each side of the restraint pad.
Make sure you hear a ???click??? on both sides.
???Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached.
8
B
B 
Free End
Strap
Toy
Toy
3
Free End
To tighten the belts:
???Feed the anchored end of the restraint belt up through the buckle to form a loop 
.
??? Pull the free end of the restraint belt B .
???Repeat this procedure to tighten the other restraint belt.
To loosen the belts:
???Feed the free end of the restraint belt up through the buckle to form a loop 
. Enlarge the loop by pulling on the end of the loop toward the buckle.
???Pull the anchored end of the restraint belt to shorten the free end of the restraint belt B .
???Repeat this procedure to loosen the other restraint belt.
??? Fit the pad straps through the slot in the toy rings. Fasten the straps.
???Or, attach the toys to the toy bar straps (please see Step 5).
Hint: Pull the monkey???s head for a short tune.
9
Toy Bar
Plug
Plug
Toys
5
??? Fit the plugs on each end of the toy bar into the sockets in each side rail.
??? Fit the toy bar straps through the slot in the toy rings. Fasten the straps.
??? Or, attach the toys to the pad straps (see Step 4).
Hint: Pull the monkey???s head for a short tune.
6
Power Switch
???Make sure your child is properly secured in the seat.
???Slide the power switch to the
on position for calming vibrations.
???Slide the power switch to the 
off position to turn vibrations off.
10
Kickstand
7
Storing the Restraint
System for Toddler Use
Small Slot
Small
Slot
???Rotate the kickstand out.
???Push down on the seat bottom to be sure the kickstand is in position.
???Insert the restraint belts back through the small slots in the pad.
???Insert the restraint pad down through the large slot in the pad.
9 
???Turn the rocker face down.
???Tuck the ends of the restraint pad underneath the buckles, as shown.
11
Care
The frame, pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue.