Platinum Edition 2-Speed

Heavy-Duty Wood Shaper

(Model 43-424)

MANUAL INSTRUCTION

1.FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING THE TOOL. Learn the tool???s application and limitations as well as the specific hazards peculiar to it.

2.KEEP GUARDS IN PLACE and in working order.

3.ALWAYS WEAR EYE PROTECTION.

4.GROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known ground. Never remove the third prong.

5.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it ???on.???

6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

7.DON???T USE IN DANGEROUS ENVIRONMENT. Don???t use power tools in damp or wet locations, or expose them to rain. Keep work area well-lighted.

8.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

9.MAKE WORKSHOP CHILDPROOF ??? with padlocks, master switches, or by removing starter keys.

10.DON???T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed.

11.USE RIGHT TOOL. Don???t force tool or attachment to do a job for which it was not designed.

12.WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

13.ALWAYS USE SAFETY GLASSES. Wear safety glasses. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. Also use face or dust mask if cutting operation is dusty.

14.SECURE WORK. Use clamps or a vise to hold work when practical. It???s safer than using your hand and frees both hands to operate tool.

15.DON???T OVERREACH. Keep proper footing and balance at all times.

16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools

sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

17. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters, etc.

18.USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause hazards or risk of injury to persons.

19.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in ???OFF??? position before plugging in power cord.

20.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.

21.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function ??? check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

22.DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

23.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don???t leave tool until it comes to a complete stop.

24.DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol or any medication.

25.MAKE SURE TOOL IS DISCONNECTED FROM POWER SUPPLY while motor is being mounted, connected or re- connected.

26.WHEN THE TOOL IS NOT IN USE, the switch should be locked in the OFF position to prevent unauthorized use of the tool.

27.WARNING: SOME DUST CREATED BY POWER

SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

???lead from lead-based paints,

???crystalline silica from bricks and cement and other masonry products, and

???arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are

1.WARNING: DO NOT OPERATE YOUR WOOD

SHAPER UNTIL IT IS COMPLETELY ASSEMBLED AND

INSTALLED ACCORDING TO THE INSTRUCTIONS.

2.IF YOU ARE NOT thoroughly familiar with the operation of Wood Shapers, obtain advice from your supervisor, instructor or other qualified person.

3.MAKE SURE wiring codes and recommended electrical connections are followed and that machine is properly grounded.

4.NEVER turn the shaper ???ON??? before clearing the table of all objects (tools, scraps of wood, etc.).

5.DO NOT process materials less than 12" in length or

4in width without special supporting fixtures. Use push sticks, featherboards or holddowns whenever possible.

6.ALWAYS use a miter gage and clamp attachment when edge shaping work less than 6" wide. The fence should be removed during this operation.

7.AVOID awkward hand positions where a sudden slip could allow your hand to contact the cutter.

8.KEEP hands away from cutting tool.

9.NEVER run the stock between the fence and the cutter.

10.DO NOT feed material that is warped, contains knots or is embedded with foreign objects, such as nails

11.NEVER start the shaper with the stock in contact with the cutter.

12.NEVER reach under the table while the machine is running.

13.NEVER perform layout, assembly or set-up work on the table while the shaper is operating.

14.KEEP cutters sharp and free from rust and pitch.

15.THE FENCE halves should be adjusted so that the cutter opening is never more than is required to clear the cutter.

16.ALWAYS lock fence hardware after making fence adjustments.

17.MAKE CERTAIN cutters are properly secured before starting machine.

18.DO NOT perform any operation freehand. ALWAYS use fence for straight shaping; miter gage for edge shaping; and starting pin and rub collars for curve shaping.

19.ALWAYS keep front motor access panel closed while operating shaper.

20. ALWAYS feed against the cutter rotation, as shown in Fig. A.

Fig. A

21. WHEN SHAPING with collars and starting pin, the collar MUST have sufficient bearing surface, as shown in Fig. B. Fig. C, illustrates the wrong way for this operation as the collar DOES NOT have sufficient bearing surface.

Fig. B

Fig. C

22. WHEN SHAPING with collars and starting pin, the work must be fairly heavy in proportion to the cut being made as shown in Fig. D. UNDER NO CIRCUMSTANCES should short work of light body be shaped against the collars as shown in Fig. E.

Fig. D

Fig. E

23. WHEN SHAPING with collars and starting pin, the cutter should be positioned below the collar whenever possible, as shown in Fig. F.

Fig. F

24.MAKE all adjustments with the power ???OFF???.

25.KEEP guard in place at all times.

26.BEFORE leaving the machine, make sure the work area is clean.

27.SHOULD any part of your shaper be missing, damaged or fail in any way, or any electrical component fail to perform properly, shut off switch and remove plug from power supply outlet. Replace missing, damaged or failed parts before resuming operation.

28.ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident Prevention Manual for Industrial Operations and also in the Safety Data Sheets provided by the NSC. Please also refer to the American National Standards Institute ANSI 01.1 Safety Require- ments for Woodworking Machinery and the U.S. Depart- ment of Labor OSHA 1912.213 Regulations.

29.SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.

4.10" Wide Cast Iron Extension Wings

5.Wrenches (2)

6.7/16-20 x 1" Hex Cap Screws (6) for mounting extension wings

7.Flat Washers (6) for mounting extension wings

8.Handwheel

9.Key for Handwheel

10.Lock Knob

11.Guard

12.3/4" I.D. Washer (2)

13.3/4" I.D. x 1/2" Thick Collar

14.3/4" I.D. x 3/4" Thick Collar

15.3/4" I.D. x 1" Thick Collar

16.Spindle Nut

17.Keyed Washer

18.Spindle

19.Tie Rod

20.Tie Rod Nut

21.Keps Nut (2) for mounting switch-to-switch mounting bracket

22.Phillips Head Screw (2) for mounting switch-to-switch mounting bracket

23.Flange Nut (4) for mounting switch mounting bracket to shaper

24.Truss Head Machine Screw (4) for mounting switch mounting bracket to shaper

25.Switch Adapter Plate (2) for mounting switch mounting bracket to shaper

26.Starting Pin

40

42

39

27.Fence Body

28.Left and Right fence halves

29.Locking Levers (2) for fence halves

30.Flat Washers (2) for locking levers

31.Spring clamp for fence guard

32.Top cover

33.Guard Mounting Bracket

34.Clear Plastic Guard

35.Hex Nuts (4) for mounting guard mounting bracket to top cover

36.Lock Washers (8) for mounting guard mounting bracket to top cover

37.Hex Soc. Hd. Screw (4) for mounting guard mounting bracket to top cover

38.Rod for fence guard

39.Holddown for fence guard

40.Brackets for fence guard (4)

41.Flat washers (2) for mounting top cover to fence body

42.Lock Knobs (2) for mounting top cover to fence body

43.Flat Washers (2) for fence locking handles

44.Fence Locking Handles (2) for mounting fence to shaper

45.Lock Bars (23) for fence halves

ASSEMBLING SPINDLE

RAISING AND

LOWERING HANDWHEEL

1.Insert key (A) Fig. 5, into slot in spindle raising and lowering shaft (B) as shown.

2.Assemble handwheel (C) Fig. 5, onto spindle shaft (B), making certain the key (A) fits into the slot (D) in the handwheel. Insert the set screw which holds the handwheel to the shaft and tighten screw firmly against key.

3.Thread lock knob (E) Fig. 6, into the spindle shaft (B).

A

B D

C

Fig. 5

B

E

Fig. 6

GB A

H F

F

G

H

L L

FK K

Fig. 9

ASSEMBLING

SWITCH BRACKET

AND ON/OFF SWITCH

1.The on/off switch (A) Fig. 9, and switch mounting bracket (B) are shipped inside the shaper cabinet. Open the side door of the shaper cabinet, remove switch package and remove packaging material.

2.Position switch mounting bracket (B) Fig. 10, so holes (C) are over hole (D) in shaper cabinet (E), then fasten bracket (B) to cabinet (E) using four truss head screws (F) Fig. 9, flange nuts (G) and two switch adapter plates (H). NOTE: Switch adapter plates (H) are to be positioned inside the shaper cabinet as shown in Fig.

3.Fig. 12, illustrates switch mounting bracket (B) properly mounted to shaper cabinet.

4.Assemble on/off switch (A) Fig. 9, to switch mounting bracket (B) Fig. 12, through two holes (J), using two Phillips head screws (K) Fig. 9, and Keps nuts

(L).

5.Fig. 13, illustrates on/off switch properly mounted to switch mounting bracket.

B

E

D

C

C

Fig. 10

H

H

Fig. 11

B

J

Fig. 12

Fig. 13

ASSEMBLING FENCE

TO SHAPER TABLE

1. The fence on this shaper can be mounted parallel to the miter gage slot using two holes (B) Fig. 14, or 90 degrees to the miter slot by using two holes (A). The following illustrates mounting the fence parallel to the miter gage.

2. Place fence body (C) Fig. 15, on the table as shown, and locate the two fence locking levers with washers (D) and fence lock bars (E).

C

D

E

Fig. 15

A

B

A

B

Fig. 14

E

D

Fig. 16

E

D

9

Fig. 17

C

F

Fig. 18

5. Fig. 19, illustrates fence body (C) fastened to the table with the two fence locking handles (F).

6. Loosen locking lever (D) Fig. 20, and slide rear of fence half (G) onto locking bar (E). Assemble remaining fence half in the same manner. Then tighten locking lever (D) to secure each fence half to the fence body.

7.Assemble guard mounting bracket (H) Fig. 21, to top cover (J) using the four inch-long hex head cap screws, hex nuts, and eight lock washers (K) as shown in Fig. 22.

8.Assemble top cover (J) Fig. 22, to top of fence body

(C) using the two locking knobs and washers (L).

9.Fig. 23, illustrates top cover properly assembled to the fence body.

C

J

L

F

C

F

Fig. 19

G

E

D

Fig. 20

J

H

K

K

Fig. 21

ASSEMBLING GUARDS

TO FENCE BODY

1. Assemble guard bracket (A) Fig. 24, and hex rod (B) to upright hex shaft (C) as shown.

2. Assemble two guard brackets (A) Fig. 25, and clear plastic guard (D) to holddown (E) as shown.

3.Assemble holddown/clear plastic guard assembly to hex rod (B) as shown in Fig. 26.

4.Assemble guard bracket (A) Fig. 27, and spring clamp (F) to hex rod (B) as shown, then tighten all wing nuts.

5.The spring guard (F), holddown (E) and clear plastic guard (D) can be flipped up out of the way as shown in Fig. 28, by lifting up on locking lever (G), when not in use or when making adjustments. CAUTION: When the guard assembly is in the down position as shown in Fig. 27, make certain locking lever (G) is in the locked position as shown.

B

A

G

F

Fig. 27

C

A

B

Fig. 24

A

A

E

D

Fig. 25

B

Fig. 26

F

E

G

D

Fig. 28

6. Fig. 29, illustrates complete fence and guard assembly mounted in the alternate position, 90 degrees to miter gage slot.

ASSEMBLING AND

CHANGING SPINDLES

MAKE CERTAIN THE MACHINE IS DISCONNECTED

FROM THE POWER SOURCE.

1. Thread one end of the tie rod (A) Fig. 30, into the threaded hole in the bottom of the spindle (B).

2.Insert tie rod and spindle into the spindle cartridge, making sure the pin (C) Fig. 31, in the spindle cartridge, is engaged with notch (D), in the spindle.

3.Fig. 32, illustrates the spindle (B), inserted into the spindle cartridge.

4.Thread nut (E) Figs. 30 and 33, onto bottom end of tie rod (A).

5.Place wrench on flats (F) Fig. 32, on top of spindle and tighten nut (E) Fig. 33, on bottom of tie rod to fasten spindle to spindle cartridge.

F

B

Fig. 32

Fig. 29

B

A

E

Fig. 30

D

C

Fig. 31

A

E

Fig. 33

MAKE CERTAIN THE MACHINE IS DISCONNECTED

FROM THE POWER SOURCE.

1. Two 1/2" I.D. and two 3/4" I.D. washers are supplied with the 4-1/2" diameter spindle guard to accommodate 1/2" and 3/4" spindles. These washers are to be positioned directly above and below the spindle guard. Place one of the washers (A) on the spindle, over either the cutter or collar, as shown in Fig. 38.

2. Place the spindle guard (B) Fig. 39, on the spindle, then place the other washer (C) and ???keyed??? washer (D) on the spindle as shown.

3.Thread spindle nut (E) Fig. 40, onto spindle, then place one wrench on flats on top of spindle and one wrench on spindle nut (E) and tighten as shown.

4.IMPORTANT: Always place ???keyed??? washer (D) Fig. 39, on spindle before screwing on spindle nut (E) Fig. 40. The ???keyed??? washer (D) Fig. 39, prevents the spindle nut (E) Fig. 40, from loosening when the spindle turns counterclockwise.

A

Fig. 38

D

C

B

Fig. 39

E

THREE HORSEPOWER

MOTORS

The motor supplied with single phase, 3 horsepower Shapers is designed to be operated from a 220-240 volt power system.

The single phase Shaper is intended to be used on a circuit that has an electrical outlet that looks like the one illustrated in Fig. 41. The tool has a plug similar to the plug illustrated in Fig. 41. Make certain the tool is connected to an outlet having the same configuration as the plug. No adapter is available, or should be used with the tool.

CAUTION: IN ALL CASES, MAKE CERTAIN

THE RECEPTACLE IN QUESTION IS PROPERLY

GROUNDED. IF YOU ARE NOT SURE, HAVE A

CERTIFIED ELECTRICIAN CHECK THE RECEPTACLE.

The single phase, three horsepower Shaper motors are single voltage motors and cannot be connected to operate at a voltage other than 220-240 volts.

If you desire to operate the single phase 3 horsepower Shaper with an extension cord, use a proper extension cord and make certain it is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Fig. 42, shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

CURRENT CARRYING PRONGS

240 VOLT

GROUND PRONG

RAISING AND

LOWERING SPINDLE

The spindle can be raised or lowered by loosening lock knob (A) Fig. 45, and turning handwheel (B). To raise the spindle height, turn the handwheel (B) clockwise. To lower the spindle height, turn handle (B) counterclockwise.

The scale (C) Fig. 45, indicates the spindle travel range from 0 to 3" and is marked in 1/16" increments. Minor cutter height adjustments can be measured using the pointer (D) along the scale (C). CAUTION: Always tighten lock knob (A) after adjusting spindle height.

CHANGING SPEEDS AND

ADJUSTING BELT TENSION

The shaper is supplied with a 2-step motor pulley and a 2-step spindle pulley that provides spindle speeds of 7,000 and 10,000 R.P.M. When the belt is on the largest step of the motor pulley and the smallest step of the spindle pulley, the spindle speed will be 10,000 R.P.M. When the belt is on the smallest step of the motor pulley and the largest step of the spindle pulley, the spindle speed will be 7,000 R.P.M.

A chart (Y) Fig. 46, illustrating the correct belt placement for 7,000 or 10,000 R.P.M. is located on the inside panel of the motor access door.

To change speeds and adjust belt tension, proceed as follows:

1.DISCONNECT THE MACHINE FROM THE POWER SOURCE and open motor access door, as shown in Fig. 46.

2.Loosen thumb screw lock (A) Fig. 47. Release tension on belt by moving lever (B), to the left. Position belt (C), on the desired steps of the spindle pulley (D), and the motor pulley (E), and apply belt tension by moving lever (B), to the right. When desired belt tension is applied to belt, retighten thumb screw lock (A).

3.Proper belt tension is attained when there is approximately 3/32" deflection using light finger pressure (approx. 3.5 lbs.) at the center of the belt span between pulleys (D) and (E) Fig. 47. IMPORTANT: Pulleys (D) and (E) should always be aligned with each other to provide maximum belt performance and reduce belt wear. To check pulley alignment, refer to section ???REPLACING

SPINDLE CARTRIDGE.???

REVERSING

SPINDLE ROTATION

MAKE CERTAIN THE MACHINE IS DISCONNECTED

FROM THE POWER SOURCE.

The motor is equipped with a reversing switch (X) Fig. 46, which is located on the motor junction box. CAUTION: Never attempt to reverse the rotation of the spindle with the motor running.

D

C

B

A

Fig. 45

X

Y

Fig. 46

C

D E

B

A

Fig. 47

GUARD CONTROLS

AND ADJUSTMENTS

DISCONNECT SHAPER FROM POWER SOURCE.

The spring clamp (A) Fig. 52, holddown (B), and clear plastic guard (C) are fully adjustable to provide safe protection for most applications. NOTE: For certain applications, the supplied spindle guard may have to be used or a custom guard may need to be fabricated.

1. Using a square (not shown), check to see if shaft (D) Fig. 52, on spring clamp (A) is 90 degrees to the table surface. If an adjustment is necessary, proceed as follows:

Lift up on guard locking handle (E) Fig. 53, loosen lock nut (F) and turn screw (G) until shaft (D) is 90 degrees to the table surface; then tighten lock nut (F).

Push down on guard locking handle (E) Figs. 53 and 54, until it locks in place as shown in Fig. 54. If the locking action is too loose or tight, loosen screw (H) and adjust cam washer (J), then tighten screw (H). Repeat this adjustment on the screw and cam washer located on the other side of guard locking handle (E).

2.Adjust holddown (B) Fig. 55, by placing a piece of material which will be used on the table as shown. Loosen thumb screws on guard mounting bracket (K) and adjust holddown (B) over top of workpiece to provide some downward pressure and tighten thumb screws.

3.Adjust clear plastic guard (L) Fig. 55, by loosening thumb screws on guard mounting bracket (M) and locating the guard so it will deflect the wood chips and provide protection from reaching the cutter; then retighten thumb screws.

C

D

B

A

Fig. 52

E

F

G

D

Fig. 53

H E

J

Fig. 54

K

L

M

B

Fig. 55

4. Loosen thumb screws on guard mounting bracket

(P) Fig. 56, and adjust spring clamp (N) so it will provide inward pressure on workpiece; then tighten thumb screws. NOTE: Thumb screws on guard mounting bracket (R) Fig. 56, can be loosened to permit extension of guard assembly.

WARNING: TURN THE CUTTER BY HAND TO MAKE

CERTAIN CUTTER DOES NOT CONTACT ANY OF THE

G U A R D I N G O R F E N C E H A LV E S B E F O R E

CONNECTING THE SHAPER TO POWER SOURCE.

CAUTION: Always make certain guard locking handle

(E) Fig. 56, is in the locked position as shown and all thumb screws are tight on guard assembly before turning shaper on.

R

P

E

N

Fig. 56

2.When the shaping operation removes the entire edge of the work, e.g., in jointing or making a full bead, the shaped edge will not be supported by the rear fence when both fences are in line, as shown in Fig. 58. In this case, the work should be advanced to the position shown in Fig. 58, and stopped.

3.The rear fence should then be advanced to contact the work, as shown in Fig. 59. The rear fence will then be in line with the cutting circle.

Fig. 57

Fig. 58

1.Collars MUST be smooth and free of all gum or other substances.

2.The edge of the work to be shaped MUST be smooth, as any irregularity in the surface which rides against the collar will be duplicated on the moulded surface.

3.A portion of the edge of the work MUST remain untouched by the cutters in order that the collar will have sufficient bearing surface. Fig. 60, illustrates the wrong way for the operation, while Fig. 61 illustrates the right way.

4.The work MUST be fairly heavy in proportion to the cut being made as shown in Fig. 62. Under NO circumstances should short work of light body be shaped against the collars as shown in Fig. 63.

5.When shaping with collars and starting pin, the Safe Guard II spindle guard, supplied with your machine, should always be used.

Fig. 60

Fig. 61

Fig. 62

POSITION OF COLLARS

1.The collars may be used in any of the following positions: above, below or between two cutters.

2.When the collar is used below the cutter, a shown in Fig. 64, the progress of the cut can be observed at all times. However, any accidental lifting of the work will gouge the wood and ruin the workpiece.

3.When the collar is used above the cutter as shown in Fig. 65, the cut cannot be seen, yet this method offers some advantage in that the cut is not affected by slight variations in the thickness of the stock. Also, accidental lifting of the work will not gouge the workpiece. Simply correct the mistake by repeating the operation.

4.The collar between cutters method, as shown in Fig. 66, has both the advantages of the first two methods and is frequently used where both edges of the work are to be shaped.

Fig. 64

Fig. 65

B

A

B

Fig. 67

STARTING PIN

1.Your machine is supplied with a tapered starting pin

(A) Fig. 67, which is used as a support when starting the cut. The starting pin (A) is placed on one of the tapered holes (B) in the table.

2.Fig. 68, illustrates starting pin (A) placed into hole in table.

3.The work should be placed in the first position using the guide pin as a support, as shown in Fig. 69. Then swing the work into the cutter as shown in the second position. The work will now be supported by the collar and starting pin as shown in Fig. 69.

4.After the cut has been started, the work is swung free of the starting pin and rides only against the collar as shown in the third position Fig. 70. ALWAYS FEED

AGAINST THE ROTATION OF THE CUTTER.

IMPORTANT: If the work would be advanced to the cutter without the side support of the starting pin, it would invariably be kicked back.

A

Fig. 68

Fig. 69

Fig. 70

High-Speed Steel

3-Lip Shaper Cutters

All have 1/2" spindle hole. Involute relief design permits honing of the face without changing the shape. Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown

3/8 size. 1/2 Lb. each.

Collar Sets 1/2" Hole

No. 43-210 Set of 7 Collars. 3/4" to 11/8" diameter. Nos. 09-142, 09-143, 09-144, 09-145, 09-171, 09-172, 09-173. 1/2 Lb.

No. 43-211 Set of 6 Collars. 13/16" to 11/2" diameter. Nos. 09-141, 09-146, 09-147, 09-148, 09-174, 09-175. 1 Lb.

No. 43-212 Set of 6 Collars. 19/16" to 17/8" diameter. Nos. 09-149, 09-176, 09-177, 09-178, 09-179, 09-180. 11/2 Lbs.

No. 43-191 Set of 4 Collars for Sash Cutters.

Nos. 09-140, 09-141, 09-150, 09-151. 1/2 Lb.

Cutter and Collar Sets ??? 1/2" Hole

No. 43-182 Standard Cutter Set. Consists of Cutters 09-100 to 09-109 inclusive and Collars 09-142 to 09-149 inclusive. Packed in wood box. 31/2 Lbs.

No. 43-213 Cove and Bead Cutter Set. Consists of Cutters 09-108, 09-127; 09-135 to 09-138 inclusive and collars 09-132 to 09-134. Packed with 43-345 Stub Spindle Assembly and SP-10 Wrench for H.D. Wood Shaper.

2 Lbs.

No. 43-214 Sash and Cabinet Cutter Set. Consists of Cutters 09-108, 09-120, 09-121, 09-123 to 09-128 inclusive and Collars 09-140, 09-141, 09-150 and 09-151. Packed with 43-345 Stub Spindle Assembly and SP-10 Wrench for H.D. Wood Shaper 3 Lb.

Spacing Collars ??? 1/2", 3/4" and 1" Holes.

Collar Sets 3/4" and 1" Hole

No. 43-248 Set of 6 Collars. 3/4" hole, 13/16" to 11/2" diameter. Nos. 43-260, 43-261, 43-262, 43-263, 43-264, 43-265.

No. 43-249 Set of 6 Collars. 3/4" hole, 19/16" to 17/8" diameter. Nos. 43-266, 43-267, 43-268, 43-269, 43-270, 43-271.

No. 43-308 Set of 5 Collars. 1" hole, 11/4" to 11/2" diameter. Nos. 43-321, 43-322, 43-323, 43-324, 43-325.

No. 43-309 Set of 6 Collars. 1" hole, 19/16" to 17/8" diameter. Nos. 43-326, 43-327, 43-328, 43-329, 43-330, 43-331.

For Heavy Duty, Utility and

43-355 Wood Shapers

No. 43-344 3-Knife Safety Cutterhead.

Enables circular saw moulding cutter to be used on the wood shaper. Includes wrench and bushing for use with 1/2" and 3/4" shaper spindles. Furnished without knives. 1 Lb.

For Heavy Duty, Utility and

43-355 Wood Shapers (continued)

No. 34-895 Auto-Set?? Miter Gage. For straight and angle shaping. Has 3/8 x 3/4 x 18 guide bar and pivoting work support body with pointer and calibrations reading through 120?? swing. Adjustable, positive stops at 90?? and 45?? positions. Accommodates No. 34-568 Clamp Attachment. 31/2 Lbs.

No. 34-568 Clamp Attachment for miter gage. Holds work evenly and safely when edge shaping with miter gage. Includes clamp bar, two sliding clamp screws, front and rear posts. 11/2 Lbs.

No. 34-873 Extra Clamp Screw and Bracket

for clamp attachment. 1/2 Lb.

No. 43-186 Sliding Shaper Jig. For horizontal shaping operations such as tenon and groove cutting. Securely holds short and narrow work, prevents slipping. 15 Lbs.

For Two-Speed Heavy Duty

Wood Shaper

No. 50-273 Mobile Base. For H.D. Shaper.

22 Lbs.

No. 43-348 Safety Ring Guard. For added safety and convenience on curved and circular edge shaping operations. Complete with mounting bracket. 9 Lbs.

No. 43-188 Sliding Shaper Jig. Provides greater cutting accuracy during a variety of shaping operations. Features three guide bar locations for positioning the workpiece as close as possible to both large and small diameter shaper cutters. Twelve mounting holes offer you a dozen options for moving the solid steel bars and cam-action clamps around the base in order to fit large and small workpieces, different machines and various types of operations. Not just for shapers, the Sliding Shaper Jig also helps you safely cut angled- tenons, tenons and dados on either left or right tilting table saws.

13 Lbs.

1/4" 42-035

3/8" 42-036

1/2" 42-037

3/4" 42-038

1" 42-039

1/4" 42-070

3/8" 42-071

1/2" 42-072

3/4" 42-073

1" 42-074

Male and Female Sash

All 215/16" diameter. 3/4" bore with 1/2" T-Bushing.

Drawer Joint

All 215/16" diameter. 3/4" bore, 1/2" T-Bushing. Requires use

of Stub Spindle.

Counterclockwise rotation only.

Straight

All 3/4" bore with 1/2" T-Bushing unless otherwise noted.

Horizontal Panel Raising

For cutting 3/4" material. With 15?? shear for optimum cutting both with and across the grain. Use 42-120 Rub Bearing with 41/2" Dia. Cutters and 42-121 Rub Bearing with 6" Dia. Cutter.

Horizontal Panel Raising

For cutting 5/8" material. With 15?? shear for optimum cutting both with and across the grain. Use 42-120 Rub Bearing with 41/2" Dia. Cutters and 42-121 Rub Bearing with 6" Dia. Cutter.

*Not supplied with 1/2" T-Bushing

Horizontal Panel Raising/

Back Cutters

With 15?? for optimum cutting both with and across the grain. Includes 1/4" tongue spacer. For use with 41/2" dia. horizontal panel raising cutters to cut 3/4" material. 33/8" diameter.

3/4" bore with 1/2" T-Bushing.

Double Sided 8-Cutter Cope and Pattern Set

Includes 1/4" and 1/2" wide x 5/8" tongue and groove cutters. All 215/16" diameter unless otherwise noted. 3/4" bore. For use with 42-122 rub bearing. For cutting 13/8" passage doors and 13/4" entry doors.

Cat. No. 42-000 Set Includes

Cat. No. Description

Cutters available separately.

Ball Bearing Rub Collars

For use with carbide-tipped cope and pattern cutter sets and horizontal panel raising cutters.

T-Bushings

Set of two. For changing bore diameters on individual carbide tipped cutters and cutter sets.

*Includes 1 long and 1 short T-Bushing