Cisco VG224 Voice Gateway

Hardware Installation Guide

Corporate Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706

USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 526-4100

Text Part Number: OL-5006-04

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco???s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco???s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

???Turn the television or radio antenna until the interference stops.

???Move the equipment to one side or the other of the television or radio.

???Move the equipment farther away from the television or radio.

???Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB???s public domain version of the UNIX operating system. All rights reserved. Copyright ?? 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED ???AS IS??? WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0501R)

Cisco VG224 Voice Gateway Hardware Installation Guide

Copyright ?? 2003-2005 Cisco Systems, Inc. All rights reserved.

C O N T E N T S

Contents

Contents

Contents

I N D E X

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

This preface discusses the audience, organization, and conventions of this publication, and describes how to obtain additional documentation.

Audience

This publication is designed for people who have some experience installing networking equipment such as routers, servers, and switches. The person installing Cisco VG224 voice gateway (VG) should be familiar with networks and telephony equipment as well as with electronic circuitry and wiring practices and have experience as an electronic or electromechanical technician.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Organization

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Conventions

Conventions

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this publication.

Timesaver Means the described action saves time. You can save time by performing the action described in the paragraph.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Tip Means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Safety Warnings

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement. To see translations of the warnings that appear in this publication, refer to the Cisco VG224 Voice Gateway Regulatory Compliance and Safety Information document that accompanied your router or go to the following URL:

http://www.cisco.com/en/US/products/hw/gatecont/ps2250/products_regulatory_approvals_and_complianc e_list.html

Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Voor een vertaling van de waarschuwingen die in deze publicatie verschijnen, dient u de vertaalde veiligheidswaarschuwingen te raadplegen die bij dit apparaat worden geleverd.

Opmerking BEWAAR DEZE INSTRUCTIES.

Varoitus T??RKEIT?? TURVALLISUUTEEN LIITTYVI?? OHJEITA

T??m?? varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin ty??skentelet mink????n laitteiston parissa, ota selv???? s??hk??kytkent??ihin liittyvist?? vaaroista ja tavanomaisista onnettomuuksien ehk??isykeinoista. T??ss?? asiakirjassa esitettyjen varoitusten k????nn??kset l??yd??t laitteen mukana toimitetuista ohjeista.

Huomautus S??ILYT?? N??M?? OHJEET

Attention IMPORTANTES INFORMATIONS DE S??CURIT??

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un ??quipement, soyez conscient des dangers pos??s par les circuits ??lectriques et familiarisez-vous avec les proc??dures couramment utilis??es pour ??viter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez les consignes de s??curit?? traduites qui accompagnent cet appareil.

Remarque CONSERVEZ CES INFORMATIONS

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Safety Warnings

Warnung WICHTIGE SICHERHEITSANWEISUNGEN

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer K??rperverletzung f??hren k??nnte. Bevor Sie mit der Arbeit an irgendeinem Ger??t beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unf??llen bewusst. ??bersetzungen der in dieser Ver??ffentlichung enthaltenen Warnhinweise sind im Lieferumfang des Ger??ts enthalten.

Hinweis BEWAHREN SIE DIESE SICHERHEITSANWEISUNGEN AUF

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le traduzioni delle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che accompagnano questo dispositivo.

Nota CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette varselssymbolet betyr fare. Du befinner deg i en situasjon som kan for??rsake personskade. F??r du utf??rer arbeid med utstyret, b??r du v??re oppmerksom p?? farene som er forbundet med elektriske kretssystemer, og du b??r v??re kjent med vanlig praksis for ?? unng?? ulykker. For ?? se oversettelser av advarslene i denne publikasjonen, se de oversatte sikkerhetsvarslene som f??lger med denne enheten.

Merk TA VARE P?? DISSE INSTRUKSJONENE

Aviso INSTRU????ES IMPORTANTES DE SEGURAN??A

Este s??mbolo de aviso significa perigo. O utilizador encontra-se numa situa????o que poder?? ser causadora de les??es corporais. Antes de iniciar a utiliza????o de qualquer equipamento, tenha em aten????o os perigos envolvidos no manuseamento de circuitos el??ctricos e familiarize-se com as pr??ticas habituais de preven????o de acidentes. Para ver tradu????es dos avisos inclu??dos nesta publica????o, consulte os avisos de seguran??a traduzidos que acompanham este dispositivo.

Nota GUARDE ESTAS INSTRU????ES

??Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este s??mbolo de aviso indica peligro. Existe riesgo para su integridad f??sica. Antes de manipular cualquier equipo, considere los riesgos de la corriente el??ctrica y familiar??cese con los procedimientos est??ndar de prevenci??n de accidentes. Vea las traducciones de las advertencias que acompa??an a este dispositivo.

Nota GUARDE ESTAS INSTRUCCIONES

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Safety Warnings

Varning! VIKTIGA S??KERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf??r arbete p?? n??gon utrustning m??ste du vara medveten om farorna med elkretsar och k??nna till vanliga f??rfaranden f??r att f??rebygga olyckor. Se ??vers??ttningarna av de varningsmeddelanden som finns i denna publikation, och se de ??versatta s??kerhetsvarningarna som medf??ljer denna anordning.

OBS! SPARA DESSA ANVISNINGAR

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Safety Warnings

Aviso INSTRU????ES IMPORTANTES DE SEGURAN??A

Este s??mbolo de aviso significa perigo. Voc?? se encontra em uma situa????o em que h?? risco de les??es corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos el??tricos e familiarize-se com as pr??ticas padr??o de preven????o de acidentes. Use o n??mero da declara????o fornecido ao final de cada aviso para localizar sua tradu????o nos avisos de seguran??a traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRU????ES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. F??r du begynder arbejde p?? udstyr, skal du v??re opm??rksom p?? de involverede risici, der er ved elektriske kredsl??b, og du skal s??tte dig ind i standardprocedurer til undg??else af ulykker. Brug erkl??ringsnummeret efter hver advarsel for at finde overs??ttelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Safety Warnings

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Related Documentation

Related Documentation

The Cisco IOS software running your Cisco voice gateway includes extensive features and functionality. For information that is beyond the scope of this document, or for additional information, use the resources listed in Table 3 on page 14.

Timesaver Make sure that you have access to the documents listed in Table 3. See the ???Obtaining Documentation??? section on page 15 for information about obtaining these documents.

1. Refer to the modular reference publications that correspond to the Cisco IOS software release installed on your Cisco VG224 voice gateway.

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Obtaining Documentation

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

???Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/index.shtml

???Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can send comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Obtaining Technical Assistance

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)???Your network is ???down,??? or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Obtaining Additional Publications and Information

Severity 2 (S2)???Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)???Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)???You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

???Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

???The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/

???Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

???Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

???Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

???World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html

Cisco VG224 Voice Gateway Hardware Installation Guide

Preface

Obtaining Additional Publications and Information

Cisco VG224 Voice Gateway Hardware Installation Guide

C H A P T E R 1

Overview of the Cisco VG224 Voice Gateway

This chapter provides a brief description of the Cisco VG224 voice gateway (VG) and contains the following sections:

???Overview, page 1-1

???Cisco VG224 Voice Gateway Deployment, page 1-4

???Interfaces and Service Capabilities, page 1-4

???Physical Description and LEDs, page 1-5

???Specifications, page 1-6

???Software Elements, page 1-7

Overview

The Cisco VG224 supports the following interfaces:

???10/100BASE-T LAN connection

???RJ-21 analog voice interface

???External/Internal compact flash

The Cisco VG224 can be housed in a rack, mounted on a wall, or set on a bench-top surface.

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means by security. Statement 1017

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Overview

Figure 1-1 Cisco VG224 Voice Gateway Front Panel

CISCO VG224

95912

The Cisco VG224 provides 24 analog foreign exchange station (FXS) voice ports with two 10/100BASE-T ports. The chassis has the following interfaces:

???RJ-21 analog voice interface

???Two 10/100BASE-T ports

???External compact flash memory

???AC and DC power inputs

Figure 1-2 shows the basic types of Cisco VG224 chassis as seen from the cabling side.

Figure 1-2 Cisco VG224 Voice Gateway Chassis

VG224-24FXS

95913

Product Serial Number Location for the Cisco VG224 Voice Gateway

The serial number label for the Cisco VG224 Voice Gateway is located on the rear of the chassis, in the middle-left side. (See Figure 1-3.)

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Overview

Figure 1-3 Serial Number Locations

A A A N N N N X X X X

VG224-24FXS

A A A N N N N X X X X

Note The serial number for the Cisco VG224 Voice Gateway is 11 characters long

103055

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Cisco VG224 Voice Gateway Deployment

Configuration Options

The following interface options are available in the Cisco VG224 voice gateway:

Table 1-1 Configuration Options

1.Analog voice interface

2.T1/E1 ports

3.10/100BASE-T ports

4.WAN interface card (data); voice interface card (voice)

5.Compact flash

Cisco VG224 Voice Gateway Deployment

Figure 1-4 shows a typical deployment scenario for the Cisco VG224 voice gateway.

Figure 1-4 Analog FXS User Interfaces with Metro Ethernet WAN Interface

Ethernet

RJ-21

VG224

Analog telephones

Distribution

panel

103038

Interfaces and Service Capabilities

The various physical ports and the services supported by each port type are described in Table 1-2.

???Two administrative ports???One console and one auxiliary.

???One or two 10/100BASE-T LAN ports.

???Cisco VG224 voice gateway for analog voice user interface is equipped with an RJ-21 port for connection to a distribution panel.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Physical Description and LEDs

Table 1-2 Cisco VG224 Voice Gateway Interfaces and Service Capabilities

1.DCE = data communications equipment

2.DTE = data terminal equipment

3.CF = compact flash memory

Physical Description and LEDs

All interface ports and LEDs are on the rear of the chassis.

Figure 1-5 Cisco VG224 Voice Gateway LEDs

1. This is not a redundant failover power supply connection. You must use either DC or AC.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Chassis Grounding

Chassis Grounding

Chassis grounding is provided through the power cable, which uses a standard grounding plug. The chassis is also equipped with two multi 4 x 0.7 screw terminals for chassis grounding. The accessory kit contains a crimp-type ground lug that attaches to the two screw terminals. For more information, refer to the ???Installing the Ground Connection??? section on page 3-11.

Port Numbering Conventions

Port numbering conventions for the Cisco VG224 are as follows:

???An external compact flash card is numbered CF 0.

???10/100BASE-T ports are numbered 10/100BASE-T 0/0 and 10/100BASE-T 0/1 from right to left.

???FXS voice port numbering begins at 2/0 and extends to 2/7, 2/15, or 2/23, depending on the number of voice ports.

Specifications

Table 1-3 Cisco VG224 Voice Gateway Technical Specifications

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Software Elements

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Software Elements

The operating system for the Cisco VG224 voice gateway is the Cisco IOS software that resides in flash memory.

Configuration Connections

You can use an ASCII terminal or a PC to configure a Cisco VG224 voice gateway. The configuration can be performed in several ways:

???Locally, with a direct connection through the console port

???Remotely, with a connection through the auxiliary port and a modem

???Through Telnet and TFTP

Configuration Methods

Automated Configuration

If your Cisco VG224 voice gateway was ordered with the Simple Network-Enabled Auto-Provision (SNAP) option, no onsite configuration is required. When the Cisco VG224 voice gateway is powered on and connected, the SNAP application downloads the applicable configuration files automatically.

Manual Configuration

When a Cisco VG224 voice gateway is first installed, use the procedure in Chapter 4, ???Power-On Procedure,??? for the initial configuration. This sets the basic communication parameters. After the Cisco VG224 voice gateway is operating and able to communicate, use the procedures in the

Cisco VG224 Voice Gateway Software Configuration Guide to configure the specific services and functions, or to make changes to the existing configuration.

There are multiple methods for configuring a Cisco VG224 voice gateway:

???System configuration dialog

???Configuration mode???Cisco IOS software command-line interface (CLI)

???setup command facility???Remote configuration through a LAN

???SNMP-based application???CiscoView or HP OpenView

???HTTP-based configuration server???Provides access to the CLI from a web browser

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 1 Overview of the Cisco VG224 Voice Gateway

Software Elements

Cisco VG224 Voice Gateway Hardware Installation Guide

C H A P T E R 2

Planning Your Installation

Before you install your Cisco VG224 voice gateway, consider the information in this chapter:

???Location and Mounting Requirements, page 2-1

???Distance Limitations for Interface Cables, page 2-5

???Interference Considerations, page 2-5

Location and Mounting Requirements

The three mounting possibilities for your Cisco VG224 voice gateway are as follows:

???Rack-mount

???Wall-mount

???Bench-top

The mounting location must provide the following:

???Access to the chassis

???Access to a suitable power source

???Access to an appropriate earth ground

???Allowance for adequate heat dissipation and airflow around the chassis

Temperature Control and Ventilation

The installation location (room, closet, or cabinet) for the Cisco VG224 should always be well ventilated and provide adequate air circulation to ensure proper cooling. The room temperature should be maintained from 32 to 122??F (0 to 50??C).

Note The Cisco VG224 voice gateway chassis is designed for front-to-back airflow.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 2 Planning Your Installation

Location and Mounting Requirements

Enclosed Racks

Caution Enclosed racks must have adequate ventilation. An enclosed rack should never be overcrowded and should have louvers and a fan.

If the Cisco VG224 voice gateway is installed in an enclosed rack with a ventilation fan at the top, make sure that heated air drawn upward from other equipment does not prevent adequate cooling.

If the chassis is installed using slide rails, check for blocked ventilation ports when it is in position in the rack or cabinet. Make sure that the ventilation ports of the Cisco VG224 voice gateway are not blocked.

Tip Baffles can help isolate exhaust air from intake air. Baffles also help draw cooling air through the cabinet. The best location for the baffles depends on the airflow patterns in the rack. You can test the airflow by experimenting with different equipment arrangements.

Wall-Mounted

If the Cisco VG224 voice gateway is installed on a wall, there should be plenty of space on both sides to ensure that there is adequate air flow through the chassis.

Bench-Mounted

If the unit is placed on a bench-top, do not stack other equipment or paper on the chassis. Provide plenty of space for air circulation (front to back). Inadequate ventilation can result in overheating and damage.

Access to Chassis

Allow space at the rear of the chassis for cable connections. Also consider the need to access the chassis for future upgrades, maintenance, and troubleshooting.

Chassis Grounding

Chassis grounding is provided through the power cable, which uses a standard grounding plug. However, the chassis also requires a reliable earth ground using the earth ground lug and hardware provided. For more information, refer to the ???Installing the Ground Connection??? section on page 3-11.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 2 Planning Your Installation

Location and Mounting Requirements

Power Source

A Cisco VG224 voice gateway with AC power supply autoselects either 100???127 volt or 200???240 volt operation. AC versions include a 6-foot (1.8-meter) electrical power cord. (A label near the power cord indicates the correct voltage, frequency, current draw, and power dissipation.)

Caution The Cisco VG224 voice gateway chassis provides inputs for both AC and DC power. Design your installation to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you need to reboot it with only a single power source.

If you suspect that your AC power is not clean???if lights flicker often or there is machinery with large motors nearby???have a qualified person test the power. Install a power conditioner if necessary.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Warning This product relies on the building???s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:120 VAC, 15A U.S. (240 VAC, 10A international) Statement 1005

Warning The device is designed for connection to TN and IT power systems. Statement 1007

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means by security. Statement 1017

The +12V DC Input Power Supply

The +12V DC power connector to use with the Cisco VG224 voice gateway is the Molex Mini-Fit Jr. 5557 series, 8 circuit dual row (Molex P/N 39-01-2085). The VG224 +12V DC power input was designed to be used with an external UPS system, and it has status signals that are reported to the VG224.

Table 2-1 shows the connector pin assignment for the +12V DC power connector pin assignment.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 2 Planning Your Installation

Location and Mounting Requirements

Table 2-1 +12V DC Connector Pin Assignment

Caution Signal pins 1, 3, 5, and 7 should be tied low to prevent the Cisco VG224 voice gateway from reporting faults on the DC power. If the +12V DC option for powering VG224 is used the AC power must not be used.

Figure 2-1 shows the +12V DC power connector.

Figure 2-1 +12V DC Power Connector

103121

Pin 5

Pin 1

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 2 Planning Your Installation

Distance Limitations for Interface Cables

Cable Types

The cable types that are used are dependent on the Cisco VG224 voice gateway that you are using. For more information, see the ???Interfaces and Service Capabilities??? section on page 1-4 and Appendix A, ???Cable Specifications and Information.???

???Fast Ethernet cables (RJ-45-to-RJ-45 straight-through cables)

???Analog voice cables (RJ-21)

Distance Limitations for Interface Cables

When planning your installation, consider distance limitations and potential electromagnetic interference (EMI) as defined by the Electronic Industries Association (EIA). Distance limitation information is included for the following VG ports:

???Fast Ethernet Maximum Distance, page 2-5

???FXS Analog Voice Port Maximum Distance, page 2-5

Fast Ethernet Maximum Distance

The maximum segment distance for Fast Ethernet is 330 feet (100 meters) (specified in IEEE 802.3).

FXS Analog Voice Port Maximum Distance

The maximum distance is established by a total allowable loop resistance, including the phone or terminal equipment, of 600 ohms.

Interference Considerations

When you run cables for any significant distance in an electromagnetic field, interference can occur between the electromagnetic field and the signals on the cables. This has two implications for the installation of terminal plant cabling:

???Unshielded plant cabling can emit radio interference.

???Strong electromagnetic interference (EMI), especially as caused by lightning or radio transmitters, can destroy the EIA/TIA-232 drivers and receivers in the Cisco VG224 voice gateway.

If you use twisted-pair cables with a good distribution of grounding conductors in your plant cabling, emitted radio interference is unlikely.

If you have cables exceeding recommended distances, or if you have cables that pass between buildings, give special consideration to the effect of lightning strikes or ground loops. If your site has these characteristics, consult experts in lightning suppression and shielding. The electromagnetic pulse caused by lightning or other high-energy phenomena can easily couple enough energy into unshielded conductors to destroy electronic devices.

Most data centers cannot resolve the infrequent, but potentially catastrophic problems just described without pulse meters and other special equipment. Take precautions to avoid these problems by providing a properly grounded and shielded environment and by installing electrical surge suppression.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 2 Planning Your Installation

Interference Considerations

If you remove any module, you must either install a module in its place or install a cover plate over the opening. All module openings must be either occupied or covered to prevent electromagnetic interference.

For advice on the prevention of electromagnetic interference, consult experts in radio-frequency interference (RFI).

Cisco VG224 Voice Gateway Hardware Installation Guide

C H A P T E R 3

Installing the Cisco VG224 Voice Gateway

This chapter contains the procedures for installing your Cisco VG224 voice gateway and consists of the following sections:

???Safety Recommendations, page 3-2

???Site Log, page 3-3

???Keeping Track???Checklist, page 3-4

???Mounting Tools and Equipment, page 3-5

???Unpacking and Inspection, page 3-5

???Rack-Mounting the Chassis, page 3-6

???Wall-Mounting the Chassis, page 3-9

???Bench-Top Installation, page 3-11

???Installing the Ground Connection, page 3-11

???Connecting Cables, page 3-14

???Ports, Connectors, and Pinouts, page 3-20

???Remote Terminal Connections (If Applicable), page 3-20

???Connecting Backup Power, page 3-21

Tip While you do this installation, record your progress and site information. See the suggested format in the ???Keeping Track???Checklist??? section on page 3-4.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Safety Recommendations

Safety Recommendations

The following information is included to alert you to safety recommendations and best practices when working with this equipment.

Maintaining Safety with Electricity

Follow these guidelines when working on equipment powered by electricity.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

General Safety Practices

Follow these guidelines to ensure personal safety and protect the equipment:

???Keep the chassis area clear and dust-free during and after installation.

???Put the removed chassis cover in a safe place.

???Keep tools away from walk areas where you and others could fall over them.

???Do not wear loose clothing that could get caught in the chassis.

???Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Safety Tips

Use these tips as safety guidelines when installing or working around this equipment.

???Locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn off the power.

???Disconnect all power before installing or removing a chassis.

???Do not work alone if potentially hazardous conditions exist.

???Never assume that power is disconnected from a circuit. Always check.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Site Log

???Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds.

???If an electrical accident occurs, proceed as follows:

???Use caution; do not become a victim yourself.

???Turn off power to the system.

???If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help.

???Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD occurs when electronic components are improperly handled; it can result in complete or intermittent failures.

Always follow ESD-prevention procedures when removing and replacing components.

???Ensure that the chassis is electrically connected to earth ground.

???Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.

???Connect the clip to the ESD-strap connection jack (to the left of the power switch on the rear of the chassis) or to an unpainted chassis frame surface.

Caution For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohm (Mohm).

Site Log

We recommend that you maintain a Site Log to record all actions relevant to the system. Site Log entries might include the following:

???Installation???Print a copy of the Installation Checklist and insert it into the Site Log.

???Upgrades and maintenance???Use the Site Log to record ongoing maintenance and expansion history. Update the Site Log to reflect the following:

???Configuration changes

???Maintenance schedules, requirements, and procedures performed

???Comments, notes, and problems

???Changes and updates to Cisco IOS software

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Keeping Track???Checklist

Keeping Track???Checklist

We recommend that you use an installation checklist and maintain a Site Log.

Installation Checklist

The Installation Checklist (see Figure 3-1) lists the tasks for installing a Cisco VG224 voice gateway. Print a copy of this checklist and mark the entries as you complete each task. For each Cisco VG224 voice gateway, include a copy of the checklist in your Site Log.

Figure 3-1 Installation Checklist

Installation Checklist for site ______________________________________________

Cisco VG name/serial number _____________________________________________

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Mounting Tools and Equipment

Mounting Tools and Equipment

Obtain the following tools and parts to install a Cisco VG224 voice gateway:

???Standard flat-blade screwdriver as required for attaching brackets to rack or wall

???Phillips screwdriver for attaching brackets to a Cisco VG224 voice gateway

???Mounting brackets and screws for 24-inch rack, if required

???Four telco machine screws, for installing the chassis in a rack (use the screw size required by the rack)

???Screws and anchors for wall-mounting, if required

???Eight wood screws or other fasteners, for installing the chassis on a wall. An additional starter screw can be used to facilitate wall-mounting.

???ESD-preventive wrist strap

In addition, you might need the following external equipment:

???Console terminal, or personal computer with terminal emulation software

???PC running terminal emulation software for administrative access

???Modem for remote access

???Analog voice RJ-21 cable

???Ethernet switch

???Modem for remote configuration

Unpacking and Inspection

Do not unpack the Cisco VG224 until you are ready to install it. If the installation site is not ready, keep the chassis in its shipping container to prevent accidental damage.

The Cisco VG224, cables, printed publications, and any optional equipment you ordered might be shipped in more than one container. When you unpack each shipping container, check the packing list to ensure that you received all the following items:

???Cisco VG224

???Power cord, 6-foot (1.8-meter)

???RJ-45-to-DB-25 adapter cable (labeled Console)

???RJ-45-to-DB-9 adapter cable (labeled Auxiliary)

???Rack-mounting brackets for 19-inch rack (one pair) with screws for attaching to chassis

???Chassis guard for wall-mounting applications

???Grounding lug and fasteners

???Cisco VG224 Voice Gateway Quick Start Guide

???Cisco VG224 Voice Gateway Regulatory Compliance and Safety Information

Inspect all items for shipping damage. If anything appears damaged, or if you encounter problems when installing or configuring your system, contact a customer service representative. (See the ???Obtaining Technical Assistance??? section on page 16.)

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Rack-Mounting the Chassis

Rack-Mounting the Chassis

Your chassis ships with a pair of brackets for use with a 19-inch rack or mounting on the wall. The bracket is shown in Figure 3-2.

Figure 3-2 Quick Mounting Bracket

88815

Mounting Screws

Two sets of mounting screws are provided, in separate packages. Take care to use each screw type, and washers as needed, in the appropriate locations. Table 3-1 clarifies the differences between rack-mounting and wall-mounting screws.

Table 3-1 Rack-Mounting Versus Wall-Mounting Screws

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Rack-Mounting the Chassis

Attaching the Brackets

To install the chassis in a rack with the rear panel forward, attach the brackets as shown in Figure 3-3.

Figure 3-3 19-Inch Rack Installation???Rear Panel Forward

95916

VG224-24FXS

To install the chassis in a center-mount telco rack, attach the brackets as shown in Figure 3-4.

Figure 3-4 Telco 19-Inch Rack Installation???Rear Panel Forward

95917

VG224-24FXS

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Rack-Mounting the Chassis

Installing the Cisco VG224 Voice Gateway in a Rack

The following warning applies only when the unit is rack-mounted:

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Statement 1006

To rack-mount the chassis, follow this procedure:

Step 1 Choose one of the methods shown in Figure 3-3 on page 3-7, or Figure 3-4 on page 3-7, and attach the long leg of the mounting brackets to the chassis, as shown.

Caution Make sure to use the correct screws for this mounting option (see Table 3-1 on page 3-6).

Screws are included for attaching the brackets to the chassis, but not for installing the chassis in a rack or on a wall. You need four additional machine screws to install the chassis in a rack. Use the screw size required by your rack. After the brackets are secured to the chassis, you can rack-mount the chassis.

Step 2 Using screws that you provide, attach the chassis to the rack as shown in Figure 3-5 on page 3-8.

Figure 3-5 Attaching the Chassis to the 19-Inch Rack

103039

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Wall-Mounting the Chassis

Wall-Mounting the Chassis

The following warning applies only when the unit is wall-mounted:

Warning This unit is intended to be mounted on a wall. Please read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 248

Caution You can wall-mount the unit with either the right or left side facing up; however, the front and rear panels must be vertical.

Note For information about obtaining the chassis guard, refer to field notice number 28655, VG224 Chassis Guard - Safety Regulation, at http://www.cisco.com/en/US/ts/fn/200/fn28655.html.

To wall-mount the chassis, follow this procedure:

Step 1 Attach the short leg of one bracket to the chassis, as shown in Figure 3-6, using two 6-32 x 1/4 slotted hex screws (provided). Be sure to use a plastic washer (provided) with each screw; the narrow end of the washer must fit into the bracket slot, facing the chassis.

Caution Be sure to use the correct screws and plastic washers for this mounting option. (See Table 3-1 on page 3-6.)

Figure 3-6 Attaching the Brackets for Wall-Mounting

???You can install a starter screw in the wall, and hook the bracket keyhole over the screw. This holds the unit in place for easy installation of the attachment screws.

???Attach both brackets to the wall.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Wall-Mounting the Chassis

Note For attaching to a wall stud, each bracket requires two #10 wood screws (round- or pan-head) with #10 washers, or two #10 washer-head screws. The screws must be long enough to penetrate at least 3/4 inch (20 mm) into supporting wood or metal wall stud.

Note For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size #10.

??? Figure 3-7 shows the orientation required for installation.

Figure 3-7 Wall-Mounting the Chassis

2

4

IAD2400CISCO

103517

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Bench-Top Installation

Bench-Top Installation

Step 1 Verify that there is a suitable AC power outlet available.

Caution Do not plug this unit into an AC outlet that does not have a UL-certified receptacle that is properly tied into building ground.

Step 2 Place the four rubber feet (from the accessory kit) in the four indentations on the underside of the chassis.This helps provide proper airflow through and around the chassis.

Step 3 Place the Cisco VG224 voice gateway on a smooth, flat surface.

Caution Do not place anything on top of the chassis that weighs more than 10 lb (4.5 kg). Excessive weight on top can damage the chassis.

Installing the Ground Connection

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning AC connected units must have a permanent ground connection in addition to the power cable ground wire. NEBS-compliant grounding satisfies this requirement. Statement 284

Warning Use copper conductors only. Statement 1025

You must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical safety standards.

???For NEBS-compliant grounding, use size AWG 6 (13 mm2) wire and the ground lug provided in the accessory kit.

???For NEC-compliant grounding, use size AWG 14 (2 mm2) or larger wire and an appropriate user-supplied ring terminal.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Installing the Ground Connection

???For EN/IEC 60950-compliant grounding, use size AWG 18 (1 mm2) or larger wire and an appropriate user-supplied ring terminal.

To ground the chassis, follow this procedure:

Step 1 Locate a suitable ground location.

Tip Use a multimeter to measure the resistance between various ground locations, such as the following:

???Between the ground of a junction box (outlet) and the ground of a power tap

???Between the ground of a junction box and a metal water pipe

???Between the Cisco VG224 voice gateway chassis and the ground of a power tap

???Between the Cisco VG224 voice gateway chassis and the ground of a junction box A good ground connection should read between 0.0 and 0.5 ohms.

Step 2 Strip one end of the ground wire to the length required for the ground lug or terminal.

???For the NEBS ground lug???approximately 0.75 in. (20 mm)

???For user-provided ring terminal???as required

Step 3 Crimp the ground wire to the ground lug or ring terminal, using a crimp tool of the appropriate size. (See Figure 3-8.)

Figure 3-8 Crimping a Ground Lug onto the Ground Wire

10360

Step 4 Attach the ground lug or ring terminal to the chassis as shown in Figure 3-9 or Figure 3-10. For the ground lug, use the two screws with captive locking washers provided. For a ring terminal, use one of the screws provided. Use a number 2 Phillips screwdriver, and tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).

Note You can orient the crimped end of the ground lug in either direction (right or left).

Step 5 Connect the other end of the ground wire to a grounding point at your site.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Installing the Ground Connection

Figure 3-9 NEBS-Compliant Chassis Ground Connection Using Ground Lug

Figure 3-10 Chassis Ground Connection Using Ring Terminal

VG224-24FXS

Ring terminal attachment

95919

103513

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

Connecting Cables

For cables not included with your Cisco VG224 voice gateway, pinout information is in Appendix A, ???Cable Specifications and Information.??? Cisco VG224 voice gateway ports are color-coded for identification.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning This product relies on the building???s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

120 VAC, 15A (240 VAC, 10A international) Statement 1005

Warning To prevent accidental discharge in the event of a power line cross, route on-premise wiring away from power cables and off-premise wiring, or use a grounded shield to separate the on-premise wiring from the power cables and off-premise wiring. A power line cross is an event, such as a lightning strike, that causes a power surge. Off-premise wiring is designed to withstand power line crosses. On-premise wiring is protected from power line crosses by a device that provides overcurrent and overvoltage protection. Nevertheless, if the on-premise wiring is in close proximity to, or not shielded from, the off-premise wiring or power cables during a lightning strike or power surge, the on-premise wiring can carry a dangerous discharge to the attached interface, equipment, and nearby personnel. Statement 338

Table 3-2 shows the results of the NEBS Type 1/3 power cross tests (tip/ring to ground) performed on the Cisco VG224 voice gateway FXS ports.

Table 3-2 Results of the NEBS Power Cross Tests on FXS Ports

Note The installation must comply with all applicable codes.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

LAN and Power Cables

These cables and connections are described in Table 3-3 and in Figure 3-11.

Table 3-3 LAN, Administrative Access, and Power Cable Selection

1. Power cables vary to meet local requirements.

Figure 3-11 LAN and Administrative Access Connections

1

3

2

Cisco VG224

4

56

95920

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

Connecting the Input Power

Caution The Cisco VG224 voice gateway chassis provides inputs for both AC and DC power. Design your installation to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you need to reboot it with only a single power source.

Cable

Use the AC power cable.

Procedure

Step 1 Connect the AC power cable (supplied) to the recessed power plug on the rear of the concentrator.

Step 2 Plug the cable into a power source with a voltage of 100 to 240 VAC.

Connecting the Console Port to a PC or an ASCII Terminal

Use the procedure in this section to connect the console port to a PC running terminal emulation software.

Note The console port does not support hardware flow control.

Cable

Use an RJ-45-to-RJ-DB-9 console cable (see item 5 in Figure 3-11 on page 3-15)

For pinouts, see Table A-1 on page A-3 and Table A-2 on page A-4 in Appendix A, ???Cable

Specifications and Information.???

Procedure

Step 1 Configure the terminal emulation software requirements:

9600 baud

8 data bits

1 stop bit no parity

no flow control

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

Connecting the Auxiliary Port to a Modem

Use the procedure in this section to connect the auxiliary port to a modem.

Cable

Use an RJ-45-to-DB25 auxiliary cable (labeled Modem).

For pinouts, see Table A-3 on page A-5 and Table A-4 on page A-5 in Appendix A, ???Cable

Specifications and Information.???

Procedure

Step 1 Connect the cable from the auxiliary port (black) to the DB-25 port on the modem. (See item 6 in Figure 3-11 on page 3-15.)

Step 2 Configure the modem.

a.Match the transmission speed of the auxiliary port (default is 9600 baud).

b.Set the hardware flow control for Data Carrier Detect (DCD) and Data Terminal Ready (DTR) operation.

Note The baud rate for the auxiliary (and console) port can be configured in software for 1200, 2400, 4800, 19200, 38400, 57600, and 115200.

Connecting the Fast Ethernet Port to the Fast Ethernet Switch

Use the procedure in this section to connect a Fast Ethernet port to the Fast Ethernet switch.

Cable

Use a straight-through Fast Ethernet cable (not included).

Procedure

Step 1 Connect the cable from a Fast Ethernet port to an available port on the Fast Ethernet switch. (See item 4 in Figure 3-11 on page 3-15.)

Step 2 Connect the second cable if it is required.

Note Not all models have two ports.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

Voice Cables

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. FXS/T3/E3 Statement 1044

Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042

The analog FXS voice cables and connections are:

Figure 3-12 WAN and Voice Connections

Distribution panel

1

Cisco VG224

95921

2

Network demarcation

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Cables

Connecting the Analog Voice Interface to a Distribution Panel

To connect the multiport analog voice interface to a distribution panel, which connects to telephones, faxes, or analog PBX equipment, use the following procedure. (See Figure 3-13.)

Cable

Use an RJ-21 cable with Amphenol 50-pin connectors (not included).

For RJ-21X/CA21A pinouts, see Table A-5 on page A-6 in Appendix A, ???Cable Specifications and Information.???

Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042

Procedure

Step 1 Connect the RJ-21 cable from the analog voice multiport to the distribution panel.

Step 2 Secure the cable in place using the strap.

Figure 3-13 Analog Voice Connection

103118

Distribution panel

RJ-21 cable

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Ports, Connectors, and Pinouts

Ports, Connectors, and Pinouts

Table 3-4 summarizes the cable connections between Cisco VG224 voice gateway and the network and user interfaces. Find the port and the equipment or network type in the table; then look at the applicable pinout table in Appendix A, ???Cable Specifications and Information.???

Table 3-4 Cable Use Reference Table

Remote Terminal Connections (If Applicable)

If you are configuring a Cisco VG224 voice gateway from a remote location, connect the modem and the remote PC or terminal to the telephone network as described in this section.

Connecting to a Modem

To connect the local modem and the remote modem to live telephone outlets, use standard telephone cables.

Connecting to a Remote PC

To link a Cisco VG224 voice gateway to a remote PC, use the following procedure:

Note The remote PC must be running terminal emulation software.

Step 1 Connect the remote PC and modem.

Step 2 Set the PC terminal emulation software requirements:

9600 baud

8 data bits

1 stop bit no parity

no flow control.

Step 3 Key in and dial the telephone number of the Cisco VG224 voice gateway external modem.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Backup Power

Connecting to a Remote ASCII Terminal

To link a Cisco VG224 voice gateway to a remote ASCII terminal, such as a VT100, use the following procedure:

Step 1 Connect the remote ASCII terminal and modem.

Step 2 Set the terminal requirements:

9600 baud

8 data bits

1 stop bit no parity

no flow control.

Step 3 Key in the telephone number of the Cisco VG224 voice gateway external modem, or, if you are using a Hayes-compatible modem, enter ATDT and the number to be dialed.

Connecting Backup Power

A Cisco VG224 voice gateway can be installed with optional backup power. Backup power to a DC-powered chassis is provided by a 12-volt battery backup system; see the ???Connecting a Backup Battery to a DC-Powered Cisco VG224??? section for connection instructions. Backup power to an AC-powered chassis is provided by an uninterruptible power supply (UPS); see the ???Connecting a UPS to an AC-Powered Cisco VG224??? section for connection instructions.

Caution The Cisco VG224 chassis provides inputs for both AC and DC power. Design your installation to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you must reboot it with only a single power source.

The maximum power requirement for the Cisco VG224 voice gateway is 70 W.

Connecting a Backup Battery to a DC-Powered Cisco VG224

Connect a 12-volt backup battery to the DC input connector on your Cisco VG224 voice gateway. Before you install a backup battery, be sure to read the installation instructions for the backup battery equipment.

Figure 3-14 shows a setup using an external backup battery.

Note Figure 3-14 shows one possible setup; please review your backup battery documents before setting up your system.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Backup Power

Figure 3-14 Connecting a Battery Backup to a DC-Powered Cisco VG224

Cisco VG224 voice gateway

AC wall plug

Battery backup

VG224-24FXS

103120

DC plug

Caution Use a backup battery only if you are not using AC to power your Cisco VG224 voice gateway. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you need to reboot it with only a single power source.

Note We recommend a 12-volt automotive battery if you require longer periods of battery backup (up to 8 hours).

Figure 3-15 shows the DC power connector. See Table 3-5 for pinout information for the DC power connector on the Cisco VG224 voice gateway.

Table 3-5 Pinouts for DC Power Connector

Figure 3-15 DC Power Connector

VG224-24FXS

103121

Pin 5

Pin 1

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Backup Power

Connecting a UPS to an AC-Powered Cisco VG224

Connect an uninterruptible power supply to the AC input on your Cisco VG224 voice gateway. Before you install a UPS, be sure to read the installation instructions for the UPS.

Figure 3-16 shows a setup using a UPS.

Note Figure 3-16 shows one possible setup; please review your UPS documents before setting up your system.

Figure 3-16 Connecting a UPS to an AC-Powered Cisco VG224

Cisco VG224 voice gateway

AC wall plug

UPS

AC plug

103119

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 3 Installing the Cisco VG224 Voice Gateway

Connecting Backup Power

Cisco VG224 Voice Gateway Hardware Installation Guide

C H A P T E R 4

Powering On the Cisco VG224 Voice Gateway

To power on your Cisco VG224 voice gateway, perform the following tasks in the order listed, as required:

???Checklist for Power-On, page 4-1

???Power-On Procedure, page 4-1

???Initial Configuration Procedures, page 4-2

???Troubleshooting, page 4-4

Checklist for Power-On

You can power on a Cisco VG224 voice gateway if it meets the requirements described in Chapter 3, ???Installing the Cisco VG224 Voice Gateway???:

???The chassis is securely mounted.

???Power cable is connected.

???Interface cables are connected.

Power-On Procedure

Perform this procedure to power on your Cisco VG224 voice gateway and verify that it goes through its initialization and self-test. When this is finished, the Cisco VG224 voice gateway is ready to configure.

To power on the Cisco VG224 voice gateway, follow this procedure:

Step 1 Power on your terminal or PC, and configure it for 9600 bps, 8 data bits, 1 stop bit, and no parity.

Step 2 Move the Cisco VG224 voice gateway power switch to the ON position.

The green LED next to the auxiliary port should come on and the fan should operate. If this does not happen, see the ???Troubleshooting??? section on page 4-4.

The following message is displayed at the end of the boot-up messages:

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 4 Powering On the Cisco VG224 Voice Gateway

Initial Configuration Procedures

Step 3 Enter no to proceed with manual configuration using the command-line interface (CLI):

Would you like to enter the initial configuration dialog? [yes/no]: no

Would you like to terminate autoinstall? [yes]

Step 4 Press Return to terminate autoinstall and continue with manual configuration.

Several messages are displayed, ending with a line similar to the following:

...

Copyright (c) 1986-2003 by cisco Systems, Inc. Compiled <date> <time> by <person>

Step 5 Press Return to bring up the Router> prompt:

...

flashfs[4]: Initialization complete. Router>

Step 6 Enter privileged EXEC mode:

Router> enable

Router#

Step 7 Continue with the next section, ???Initial Configuration Procedures.???

Note If the rommon 1> prompt appears, your system has booted in ROM monitor mode. For information on the ROM monitor, refer to the router rebooting and ROM monitor information in the Cisco IOS Configuration Fundamentals Configuration Guide for your Cisco IOS software release.

Initial Configuration Procedures

Manual Configuration

To configure the Cisco VG224 voice gateway from a console (locally or remotely), refer to the

Cisco VG224 Voice Gateway Software Configuration Guide for the configuration instructions. To configure it remotely through Telnet, continue to the ???Setting the Fast Ethernet Port IP Address??? section on page 4-3 to set an Ethernet or Fast Ethernet (10/100BASE-T) port IP address.

For information about obtaining any referenced documentation, see the ???Obtaining Technical

Assistance??? section on page 16.

This section shows how to prepare the Cisco VG224 voice gateway to perform basic communication functions through its 10/100BASE-T interfaces.

Note The Console port is above the AUX port.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 4 Powering On the Cisco VG224 Voice Gateway

Initial Configuration Procedures

Perform the following initial configuration procedures, as applicable:

???Getting Your Network Information, page 4-3

???Setting the Fast Ethernet Port IP Address, page 4-3

???Verifying and Saving Your Configuration, page 4-4

Getting Your Network Information

Before you begin the configuration process, get the IP address for the 10/100BASE-T ports.

Setting the Fast Ethernet Port IP Address

To configure the Cisco VG224 voice gateway remotely through a Fast Ethernet connection, connect the 10/100BASE-T port to a live Ethernet connection using a standard Ethernet cable with RJ-45 connectors; then complete this procedure to set the IP address for the port. After setting this address, you can configure the Cisco VG224 voice gateway remotely through a Telnet connection.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 4 Powering On the Cisco VG224 Voice Gateway

Troubleshooting

Verifying and Saving Your Configuration

To verify the configuration and save it in NVRAM so that the configuration remains in effect if the Cisco VG224 is restarted, enter the following commands:

Troubleshooting

This section describes possible mechanical problems and corrective actions.

If there appears to be a malfunction, first check all cables and connections. If these are in order, see Table 4-1 for specific troubles and solutions.

For problems with the configuration, refer to the Cisco VG224 Voice Gateway Software Configuration Guide at the following URL:

http://cisco.com/en/US/docs/routers/access/vg224/software/configuration/guide/scg.html

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 4 Powering On the Cisco VG224 Voice Gateway

Troubleshooting

Table 4-1 Troubleshooting the Cisco VG224 Voice Gateway

1. See the ???Obtaining Technical Assistance??? section on page 16.

Cisco VG224 Voice Gateway Hardware Installation Guide

Chapter 4 Powering On the Cisco VG224 Voice Gateway

Troubleshooting

Cisco VG224 Voice Gateway Hardware Installation Guide

A P P E N D I X A

Cable Specifications and Information

This appendix provides the connector and pinout information you need for making or purchasing cables used with Cisco VG224 voice gateway. To order cables from Cisco, see the ???Obtaining Technical Assistance??? section on page 16. This appendix contains the following sections:

???Console and Auxiliary Port Cables and Pinouts, page A-1

???Fast Ethernet Port Pinouts (RJ-45), page A-6

???Analog Voice Multiport Pinouts (RJ-21X/CA21A), page A-7

The following list shows you which table to see for pinout information:

Console and Auxiliary Port Cables and Pinouts

Your Cisco VG224 voice gateway comes with the cable and adapters you need to connect a PC, an ASCII terminal, or a modem to your Cisco VG224 voice gateway. The cable kit includes:

???RJ-45-to-RJ-45 rollover cable

???RJ-45-to-DB-9 adapter cable for console connection

???RJ-45-to-DB-25 adapter cable for modem connection

The following illustrations and tables provide cable pinout information:

???Console port to a PC???See Table A-1 and Table A-4

???Console port to an ASCII terminal???See Table A-2 and Table A-4

???Auxiliary port to a modem???See Table A-3 and Table A-4

The console port is configured as data communications equipment (DCE); the auxiliary port is configured as data terminal equipment (DTE). Both are asynchronous serial ports and use RJ-45 connectors.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Console and Auxiliary Port Cables and Pinouts

Identifying a Rollover Cable

You can identify a rollover cable by holding the plugs side by side, with the tab at the back and comparing the modular plugs at the two ends of the cable. The wire connected to the pin on the outside of the left plug should be the same color as the wire connected to the pin on the outside of the right plug. (See Figure A-1 on page A-2.)

If your cable comes from Cisco Systems, pin 1 is white on one plug, and pin 8 is white on the opposite plug. (A rollover cable reverses the wire connections at the opposite ends: 1 to 8, 2 to 7, 3 to 6, 4 to 5, 5 to 4, 6 to 3, 7 to 2, and 8 to 1.)

Figure A-1 Identifying a Rollover Cable

Pin 1 and pin 8 are the same color

H11417

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Console and Auxiliary Port Cables and Pinouts

Console Port to PC

Figure A-2 shows the RJ-45-to-RJ-45 rollover cable assembly and the RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL); Table A-1 lists the pinouts.

Figure A-2 Console Port to PC???Cable and Adapter

5

1

H11192

Table A-1 Console Port to PC???Cable Pinouts (RJ-45 to DB-9)

1. Pin 1 is connected to pin 8 inside the Cisco VG224 voice gateway.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Console and Auxiliary Port Cables and Pinouts

Console Port to ASCII Terminal

Figure A-3 shows the RJ-45-to-RJ-45 rollover cable assembly and the RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL); Table A-2 lists the pinouts.

Figure A-3 Console Port to ASCII Terminal???Cable and Adapter

RJ-45-to-DB-25 female adapter

RJ-45 cable

8 1

CAB-500DTF

TERMINAL

25

13

1

14

H11193

Table A-2 Console Port to ASCII Terminal???Cable Pinouts (RJ-45 to DB-25)

1. Pin 1 is connected to pin 8 inside the Cisco VG224 voice gateway.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Console and Auxiliary Port Cables and Pinouts

Auxiliary Port to Modem

Figure A-4 shows the RJ-45-to-RJ-45 rollover cable assembly and the RJ-45-to-DB-25 male DCE adapter (labeled MODEM); Table A-3 on page A-5 lists the pinouts.

Figure A-4 Auxiliary Port to Modem???Cable and Adapter

RJ-45-to-DB-25 male adapter

RJ-45 cable

8 1

14

CAB-5MODCM

MODEM

25

1

13

H11194

Table A-3 Auxiliary Port to Modem???Cable Pinouts (RJ-45 to DB-25)

Alternative Connections to Terminal and Modem

Your Cisco VG224 voice gateway ships with an RJ-45-to-RJ-45 rollover cable and two adapters for connection to a PC, a terminal, or a modem. If you want to use an RJ-45 straight-through cable or other adapters, see Table A-4 for usable cable and adapter combinations.

Table A-4 Alternative Terminal and Modem Connections

1.An octal cable or RJ-45 breakout cable is equivalent to a rollover cable.

2.Modify the DB-25 adapter by removing the wire in pin 6 and placing it in the pin 8 position.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Fast Ethernet Port Pinouts (RJ-45)

Fast Ethernet Port Pinouts (RJ-45)

Figure A-5 shows the RJ-45 connector wiring for the Fast Ethernet cable; Figure A-5 lists the pinouts.

Note Pinout shown is for category 3, 4, or 5 10/100BASE-T connection to an Fast Ethernet switch.

Figure A-5 RJ-45 Connector Wiring

1. Any pin not referenced is not connected.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Analog Voice Multiport Pinouts (RJ-21X/CA21A)

Analog Voice Multiport Pinouts (RJ-21X/CA21A)

Figure A-6 shows the RJ-21 connector wiring for the cable used for the multiport analog voice interface.

Figure A-6 RJ-21 Connector Wiring

36484

Table A-6 lists the pinouts for the RJ-21 connector.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Analog Voice Multiport Pinouts (RJ-21X/CA21A)

EIA/TIA-232 Connections

The EIA/TIA-232 standard supports unbalanced circuits at signal speeds up to 64 kbps.

For connection to a Cisco VG224 voice gateway serial port, use the EIA/TIA-232 serial transition cable with the Cisco 12-in-1 connector on one end and a DB-25 connector (as shown in Figure A-7) on the other. The DB-25 connector can be male for DTE or female for DCE. To order a cable, see the ???Obtaining Technical Assistance??? section on page 16.

Figure A-7 EIA/TIA-232 Serial Transition Cable Connectors

DTE

DCE

194831

EIA/TIA-449 Connections

The EIA/TIA-449 standard, which supports balanced and unbalanced transmissions, is a faster (up to 2 Mbps) version of the EIA/TIA-232 standard that provides more functions and supports transmission over greater distances.

The EIA/TIA-449 standard was intended to replace the EIA/TIA-232 standard. However, this standard was not widely adopted because of the large installed base of DB-25 hardware. Also, the larger size of the 37-pin EIA/TIA-449 connectors limited the number of connections possible (fewer than are possible with the smaller, 25-pin EIA/TIA-232 connector).

To make a connection to a Cisco VG224 voice gateway serial port, use the EIA/TIA-449 serial transition cable with the Cisco 12-in-1 connector on one end and a DB-37 connector (as shown in Figure A-8) on the other. The DB-37 connector can be male for DTE or female for DCE. To order a cable, see the ???Obtaining Technical Assistance??? section on page 16.

Figure A-8 EIA/TIA-449 Serial Transition Cable Connectors

DTE

DCE

194832

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Analog Voice Multiport Pinouts (RJ-21X/CA21A)

V.35 Connections

The V.35 standard is recommended for speeds up to 48 kbps, although in practice it is used successfully at 4 Mbps. The Cisco VG224 voice gateway supports speeds up to 2.048 Mbps.

Use the V.35 serial transition cable (not included) with the Cisco 12-in-1 connector on one end and a standard 34-pin Winchester-type connector (as shown in Figure A-9) on the other. The 34-pin Winchester-type connector can be male for DTE or female for DCE. To order a cable, see the ???Obtaining Technical Assistance??? section on page 16.

Figure A-9 V.35 Serial Transition Cable Connectors

159

DTE

DCE

194833

X.21 Connections

The X.21 connector uses a 15-pin connector for balanced circuits and is commonly used in the

United Kingdom to connect to the public data network. X.21 relocates some of the logic functions to the DTE and DCE interfaces and, as a result, requires fewer circuits and a smaller connector than EIA/TIA-232.

Use the X.21 serial transition cable (not included) with the Cisco 12-in-1 connector on one end and a DB-15 connector (as shown in Figure A-10) on the other. The DB-15 connector can be male for DTE or female for DCE. To order a cable, see the ???Obtaining Technical Assistance??? section on page 16.

Figure A-10 X.21 Serial Transition Cable Connectors

DTE

DCE

194834

EIA/TIA-530 Connections

The EIA/TIA-530 standard, which supports balanced transmission, provides the increased functionality, speed, and distance of EIA/TIA-449 on the smaller, DB-25 connector used for EIA/TIA-232. Like EIA/TIA-449, EIA/TIA-530 refers to the electrical specifications of EIA/TIA-422 and EIA/TIA-423. Although the specification recommends a maximum speed of 2 Mbps, EIA/TIA-530 is used successfully at 4 Mbps or faster speeds over short distances. Cisco VG224 voice gateway supports speeds up to 2.048 Mbps.

Use the EIA/TIA-530 serial transition cable (not included) with the Cisco 12-in-1 connector on one end and a DB-25 connector (as shown in Figure A-11) on the other. The DB-25 connector can be male for DTE or female for DCE. To order a cable, see the ???Obtaining Technical Assistance??? section on page 16.

Cisco VG224 Voice Gateway Hardware Installation Guide

Appendix A Cable Specifications and Information

Analog Voice Multiport Pinouts (RJ-21X/CA21A)

Figure A-11 EIA/TIA-530 Serial Transition Cable Connectors

DTE

DCE

194831

Cisco VG224 Voice Gateway Hardware Installation Guide

Numerics

A

AC power requirements 2-3, 3-16 adapter pinouts A-3, A-4, A-5 adapters A-1

alternative terminal and modem connections A-5

B

backup battery 3-21, 3-23 brackets 3-6, 3-9

C

Cisco IOS software documentation xiv computer, for configuration 3-5

I N D E X

console port 3-16, A-1, A-4, A-5

console port to ASCII terminal (RJ-45 to DB-25) A-4 console port to PC (RJ-45 to DB-9) A-3

crimping the ground lug onto the Ground wire 3-12

D

documentation xiv

E

EIA/TIA-232 A-7

EIA/TIA-449 A-7

EIA/TIA-530 A-9

electrical safety guidelines 3-2 electromagnetic interference

See EMI

electrostatic discharge

See ESD

F

fan, cooling 1-6

Fast Ethernet (10/100BASE-T) port pinouts A-6

Cisco VG224 Voice Gateway Hardware Installation Guide

3-16
2-4

Index

Attaching the Chassis to the 19-Inch Rack???Rear Panel

I

identifying a rollover cable A-2 indicators

See LEDs

installation 3-4, 3-5, 3-6

installation checklist 3-4 interface options 1-1

IOS

See Cisco IOS software

L

lightning, EMI effects 2-4

log, record keeping 3-3

M

malfunctions, how to diagnose 4-4

N

noise level, fan 1-6

G

ground loops, EMI effects of

H

humidity specification 1-6

O

operating system 1-7

P

packing list 3-5

PC connections 3-20, A-3, A-5

pinout information, summarized A-1 pinouts A-3, A-4, A-6

power connection, AC

Cisco VG224 Voice Gateway Hardware Installation Guide

3-20

problems, diagnosing and correcting 4-4

R

S

safety 3-2, 3-3

serial transition cable connectors A-9

T

tables

Alternative Terminal and Modem Connections A-5

Auxiliary Port to Modem???Cable Pinouts (RJ-45 to DB-25) A-5

Cable Use Reference Table

Index

Console Port to ASCII Terminal???Cable Pinouts (RJ-45 to DB-25) A-4

Console Port to PC???Cable Pinouts (RJ-45 to DB-9) A-3

Fast Ethernet (10/100BASE-T) Port Pinouts

(RJ-45) A-6

Telco 19-Inch rack installation???rear panel forward 3-7

telco rack 3-7

Telnet 1-7

temperature specification 1-6

terminal (console) connections A-4, A-5

U

uninterruptible power supply 3-21, 3-23

V

V.35 A-8

ventilation recommendations 2-2

voltage selection, AC 2-3

W

wall-mounting the chassis 3-9, 3-10 warnings 2-3

X

X.21 A-8

Cisco VG224 Voice Gateway Hardware Installation Guide