C H A P T E R 1

Hardware Description

This chapter provides an overview of the Cisco 6200 advanced digital subscriber line access multiplexer (DSLAM) and describes the system???s hardware components. The chapter is arranged as follows:

Warning For translations of the safety warnings in this chapter, see Appendix C, ???Translated Safety Warnings.???

1.1 Cisco DSL Product Family

The Cisco 6200 is part of a family of digital subscriber line (DSL) products that provide end-to-end service, carrying data between the subscriber???s home or of???ce, the telephone central of???ce (CO), and the networks beyond. The Cisco 6000 family includes the following members:

???The Cisco 6200 DSLAM is a CO-grade multiplexer that supports up to 80 asymmetric digital subscriber line (ADSL) ports. The Cisco 6200 sends and receives subscriber data (often Internet service) over existing copper telephone lines, concentrating all traf???c onto a single high-speed trunk for transport to the Internet or the enterprise intranet.

???ADSL customer premises equipment (CPE) devices, which reside at the subscriber site connected to PCs or routers, modulate data so that it can travel over telephone lines to the Cisco 6200 DSLAM at the CO. CPE devices in the Cisco DSL product family include the Cisco 675 and the Cisco 605.

???The Cisco 6200 Manager is an SNMP-based element management application that provides con???guration, monitoring, and management support. The Cisco 6200 Manager offers a graphical user interface and runs under Windows NT 4.0 and higher. A separate console interface to the Cisco 6200 DSLAM provides command line access to all management services.

???ADSL plain old telephone service (POTS) splitters, or voice ???lters, located both at the subscriber premises and at the CO, support simultaneous voice and data transmission. (If a subscriber is using a telephone line for data only, the POTS splitter connection is not required.)

The Cisco DSL family also includes a Frame Relay IDSL multiplexer, a service selection gateway, the Cisco 605 card, the Cisco 6100 DSLAM, and an ATM switch to aggregate Cisco 6200 traf???c.

1.2 Cisco 6200 Chassis

This section describes the chassis that houses the Cisco 6200 DSLAM.

The Cisco 6200 consists of circuitry and connections that reside within a shelf or chassis that allows modular insertion and removal of the various ???eld-replaceable units (FRUs). The chassis consists of a module compartment, a fan compartment, a power module compartment, a backplane, and I/O cabling. Figure 1-1 shows the front of the chassis; Figure 1-2 shows the back.

1.2.1 Module Compartment

The module compartment holds all circuitry that relates to Cisco 6200 operation. The module compartment includes 14 slots that hold the modules (cards):

All Cisco 6200 cards can be installed and removed while the rest of the system continues to operate. (However, the system cannot pass data if the NTC is removed.) The NTC, MPC, and SLCs are described later in this chapter.

1-2 Cisco 6200 User Guide

1.2.2 Backplane

Located behind the module compartment, the backplane provides the following services:

???Interconnects the MPC, NTC, and SLCs

???Connects the SLCs with the subscribers (local loops) or the POTS splitter

???Distributes power, clocking, and other common signals to all the modules

12686

Primary (A) and Secondary (B) H-Buses

The backplane???s primary and secondary H-buses (horizontal buses) link the MPC, NTC, and SLCs. In this release, the primary bus carries all traf???c. The buses operate at 160 Mbps total throughput.

Each H-bus has two parts:

???A downstream component broadcasts all cells received from the NTC interface to each SLC. (Logic on the SLC ???lters and directs cells destined for each port.)

???An upstream component provides a contention mechanism for cells received from subscriber ports to be funneled into the upstream NTC path.

Ethernet Management Bus

A 10Base2-type Ethernet bus in the backplane carries internal management traf???c between the cards.

1-4 Cisco 6200 User Guide

Connections to POTS Splitters or Telephone Lines

On the inner surface of the backplane, the upper and lower SLC connectors connect the SLC in the corresponding slot (5 to 14) with unshielded twisted pair (UTP) lines. These lines connect to an external POTS splitter, and from there to subscribers over telephone lines. (If a subscriber is using a telephone line for data only, the POTS splitter is not required.)

Ten factory-installed dangler cables provide DSL subscriber connections. Each dangler cable ends with a 50-pin female Champ Telco connector (Figure 1-3), and each carries eight pairs to a single SLC module. For a pinout list and an illustration showing the connectors on the rear panel, see Appendix A, ???Pin Assignments.???

Figure 1-3 Telco Champ Connector

11963

Alarm Relay Connection

Backplane connector J39, accessible from the rear of the chassis, is the alarm relay connector. The alarm relays provide relay contact closures. The alarm relays transmit critical, major, and minor alarms to a separate, external alarm device within the CO. The alarm device uses a bell, light, or other signal to alert CO support personnel of the change in status. (The alarm relay transmits audible and visual alarms on separate circuits.) Alarms transmitted through J39 are also communicated by all of the following methods:

???Alarm LEDs (labeled Critical, Major, and Minor) on the MPC. (Some alarms also affect the TD and RD LEDs on the NTC.)

???Event messages on the console.

???Component status display of the Cisco 6200 Manager.

To turn off an audible alarm, do one of the following:

Cutting off an alarm has no effect on the alarm status of the system or on the indication of visual alarms. To clear an alarm, you must correct the condition that caused it. To get information about the source of an alarm, do one of the following:

???Use the Cisco 6200 Manager. (See the User Guide for the Cisco 6200 Manager for instructions.)

???Use the command show dsl alarms. (See Chapter 7, ???Troubleshooting,??? for more information on this command.)

For a pinout list and additional information on connecting alarm relays, see Appendix A, ???Pin Assignments.???

Auxiliary Port

J40, a 9-pin female connector on the Cisco 6200 backplane, is an EIA/TIA-232 (RS-232) serial port connecting to the management processor card (MPC). J40 is an auxiliary craft port that can be used to connect devices such as terminals, modems, or laptop computers to the Cisco 6200. It is accessible from the rear of the chassis. For a pinout list, see Appendix A, ???Pin Assignments.???

Power Terminals

J17, J18, J19, and J20, located at the upper right corner of the rear panel, are screw terminals for ???48 VDC power input and return:

Power circuit A is connected to the power entry module (PEM) on the left (as you face the front of the chassis); power circuit B is connected to the PEM on the right.

Unused Connectors

The Cisco 6200 backplane contains several connectors and a jumper that are not used in the current release. See Appendix A, ???Pin Assignments,??? for a list of the unused items.

1.2.3 Fan Tray

The fan tray, located at the bottom of the chassis, houses eight fans that maintain proper temperatures inside the chassis, plus an air ???lter. The ???lter should be removed and cleaned periodically. Refer to Chapter 6, ???Preventive Maintenance,??? for complete information on cleaning the air ???lter.

Caution The Cisco 6200 cooling fans must run continuously. The system may suffer thermal damage if the fans stop for more than 10 minutes. (At ambient temperatures above 104 F(40 C),thermal damage may occur sooner.)

1.2.4 Power Entry Modules (PEMs)

One or two PEMs distribute DC power to the chassis. The Cisco 6200 needs only one active PEM to operate; if two PEMs are installed, the second PEM???s power source serves as a hot backup to the ???rst PEM???s power source.

Each PEM is connected to a single DC power source. For power redundancy, two PEMs must be installed, and two separate DC power sources must be connected to the chassis. If one power source is connected, only one PEM is required. There is no bene???t to connecting two power sources to a chassis with one PEM, or to installing two PEMs in a chassis with one power source.

The PEMs reside at the top of the Cisco 6200 chassis, and they are installed and accessed from the front. DC power (???48V) enters the chassis through screw terminals on the rear panel of the chassis. The PEMs receive power through the backplane and internal cabling.

The power bay on the left is wired to power circuit A; the bay on the right is wired to power circuit B. (The circuits are identi???ed at the power terminals on the backplane.)

1-6 Cisco 6200 User Guide

The following ???xtures are present on the front panel of each PEM:

???A green LED that comes on to indicate that ???48 VDC power is available to the chassis

???A circuit breaker

Note To turn off a Cisco 6200 that has two PEMs, you must ???ip the circuit breakers on both

PEMs to OFF (0).

1.2.5 Cooling Vents

The cooling vents are located on the sides, front, and back of the Cisco 6200 chassis, as shown in Figure 1-4. Air ???ows in at the bottom of the chassis, and ???ows out at the top. Do not obstruct the intake and exhaust vents in any way.

Figure 1-4 Air Flow Through Intake and Exhaust Vents

12687

1.2.6 DSLAM Speci???cations

Table 1-1 lists the speci???cations of the Cisco 6200 DSLAM. Table 1-2 lists standards and certi???cations for the Cisco 6200 DSLAM.

Warning To prevent a Cisco 6200 system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 131??F (55??C).

1A fully loaded chassis has 1 fan tray, 2 PEMs, 1 MPC, 1 NTC, 10 SLCs, covers, and dangler cables.

2A chassis with no cards has 1 fan tray, 2 power entry modules, covers, and dangler cables.

3The chassis can operate safely at short term operating temperatures only if all of the fans are working properly. If a fan fails in a chassis that is experiencing an ambient temperature above 104 F (40 C), thermal damage may occur.

1-8 Cisco 6200 User Guide

1.3 Network Trunk Cards (NTCs)

This section describes the OC-3c and STM-1 network trunk cards (NTCs). The NTC module resides in slot 1 of the Cisco 6200 chassis.

1.3.1 What is the NTC OC-3?

The NTC is a service interface module that concentrates the data traf???c from all Cisco 6200 subscriber ports and connects the node to a single trunk line from the service-providing ATM network. This full-duplex channel unit carries data both downstream (to the subscriber) and upstream (from the subscriber).

In Release 1, the trunk is a full-duplex OC-3c ???ber optic channel. One OC-3c channel terminates at a single NTC.

The OC3 NTC is available in both single-mode and multimode versions. Multimode ???ber is LED-driven and is designed for distances up to 2 kilometers (1.2 miles). Longer distances (up to 15 kilometers or 9.2 miles) require laser-driven single-mode ???ber.

In the downstream direction, the OC3 NTC accepts ATM cells at the OC-3c rate (155.52 Mbps) and adapts these cells to the Cisco 6200 internal bus.

The OC3 NTC also transmits upstream data back to the service provider via ATM on the OC-3c physical layer.

The Cisco 6200 uses a ???xed mapping of permanent virtual channels (PVCs) between trunk and subscriber ports. This means that no con???guration of these circuits is required. Thirty-one PVCs link each subscriber port to the trunk port on the NTC. These subscriber traf???c PVCs are assigned virtual channel identi???ers (VCIs) 33 through 63. VCIs 0 through 31 are reserved for control traf???c. All of these VCs use virtual path identi???er (VPI) 0. See the chapter ???Command Reference??? for instructions on using the command show dsl vcmap to display the VCIs assigned to a particular slot or port.

The OC3 NTC collects ATM cell counts, which are accessible through the 6200 Management

Information Base (MIB). These cell count include:

The OC3 NTC provides bidirectional adaptation between serial ATM cells within the OC-3c ???ber and the 16-bit-parallel format on the backplane???s 160-Mbps H-bus. Three basic circuits perform this adaptation process:

Figure 1-5 shows how the three circuits interact.

Figure 1-5 NTC OC-3 Application

Downstream data transfer

Line module

Upstream data transfer

12688

The optical interface performs the optical-to-electrical and electrical-to-optical conversions. Its other tasks include clock recovery, overhead processing, cell delineation, and diagnostic information retrieval.

The upstream data transfer unit receives data via a 16-bit parallel input from the internal bus on the node???s backplane. ATM cells are received from an SLC channel only after that channel has won access to the upstream data bus from the other contending line channels. The upstream data transfer unit monitors the contention bus to direct inbound data to the optical interface.

The downstream data transfer unit inserts data onto the bus. This circuit inserts idle cells when a full data cell is not yet ready for transmission.

1.3.2 NTC OC-3: Physical Description

The NTC resides in slot 1 (the left-most slot as you face the front of the chassis). Each OC-3 NTC faceplate is marked NTC OC3-SM (single-mode) or NTC OC3-MM (multimode). The faceplate (see Figure 1-6) includes the ???xtures discussed in the following paragraphs.

OC-3c Trunk Port

The dual SC connectors (one for transmitting, one for receiving) for the Cisco 6200 network trunk port are recessed into the OC-3 NTC faceplate to prevent the cables from protruding too far outside the faceplate.

Warning Class 1 laser product.

Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures.

1-10 Cisco 6200 User Guide

The ???ber optic communication channels in the single-mode OC-3c card (NTC OC3-SM) operate with laser energy, which can be harmful, especially to the eyes. During normal operation this energy is con???ned to the cable and presents no danger. To avoid injury when you are connecting or disconnecting optical channels, observe these precautions:

???Always disconnect the card from the backplane before connecting or disconnecting optical cables.

Reset Switch

The reset switch is recessed behind the faceplate to avoid accidental disturbance. It is not for customer use.

Figure 1-6 NTC OC-3 Faceplates

LED Indicators

Table 1-3 describes the LEDs on the faceplate of the OC-3 NTC.

1-12 Cisco 6200 User Guide

1.3.3 NTC OC-3 Speci???cations

Table 1-4 lists the physical and electrical speci???cations of the NTC.

1.3.4 What is the NTC STM-1?

The NTC STM-1 is a service interface module that concentrates the data traf???c from all Cisco 6200 subscriber ports and connects the node to a single trunk line from the service-providing ATM network. This full-duplex channel unit carries data both downstream (to the subscriber) and upstream (from the subscriber).

The trunk is a full-duplex STM-1 ???ber optic channel. One STM-1 channel terminates at a single

NTC.

The NTC STM-1 is available in both single-mode and multimode versions. Multimode ???ber is LED-driven and is designed for distances up to 2 kilometers (1.2 miles). Longer distances (up to 15 kilometers or 9.2 miles) require laser-driven single-mode ???ber.

In the downstream direction, the NTC STM-1 accepts ATM cells at the SDH rate (155.52 Mbps) and adapts these cells to the Cisco 6200 internal bus.

The NTC STM-1 also transmits upstream data back to the service provider via ATM on the STM-1 physical layer.

The Cisco 6200 uses a ???xed mapping of permanent virtual channels (PVCs) between trunk and subscriber ports. This means that no con???guration of these circuits is required. Thirty-one PVCs link each subscriber port to the trunk port on the NTC. These subscriber traf???c PVCs are assigned virtual channel identi???ers (VCIs) 33 through 63. VCIs 0 through 31 are reserved for control traf???c. All of these VCs use virtual path identi???er (VPI) 0. See the Cisco 6200 User Guide for instructions on using the command show dsl vcmap to display the VCIs assigned to a particular slot or port.

The NTC STM-1 collects ATM cell counts, which are accessible through the 6200 Management

Information Base (MIB). These cell count include:

The NTC STM-1 provides bidirectional adaptation between serial ATM cells within the STM-1 ???ber and the 16-bit-parallel format on the backplane???s 160-Mbps H-bus. Three basic circuits perform this adaptation process:

Figure 1-7 shows how the three circuits interact.

Figure 1-7 NTC STM-1 Application

Downstream data transfer

Line module

Upstream data transfer

14270

The optical interface performs the optical-to-electrical and electrical-to-optical conversions. Its other tasks include clock recovery, cell delineation, and diagnostic information retrieval.

1-14 Cisco 6200 User Guide

The upstream data transfer unit receives data via a 16-bit parallel input from the internal bus on the node???s backplane. ATM cells are received from a subscriber line card (SLC) channel only after that channel has won access to the upstream data bus from the other contending line channels. The upstream data transfer unit monitors the contention bus to direct inbound data to the optical interface.

The downstream data transfer unit inserts data onto the bus. This circuit inserts idle cells when a full data cell is not yet ready for transmission.

1.3.5 NTC STM-1: Physical Description

The NTC resides in slot 1 (the left-most slot as you face the front of the chassis). Each NTC STM-1 faceplate is marked NTC STM1-SM (single-mode) or NTC STM1-MM (multimode). The faceplates (see Figure 1-8) include the ???xtures discussed in the following paragraphs.

Trunk Port

The dual SC connectors (one for transmitting, one for receiving) for the Cisco 6200 network trunk port are recessed into the NTC faceplate to prevent the cables from protruding too far outside the faceplate.

Warning Class 1 laser product.

Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures.

The ???ber optic communication channels in the single-mode trunk card (NTC STM1-SM) operate with laser energy, which can be harmful, especially to the eyes. During normal operation this energy is con???ned to the cable and presents no danger. To avoid injury when you are connecting or disconnecting optical channels, observe these precautions:

???Always disconnect the card from the backplane before connecting or disconnecting optical cables.

Reset Switch

The reset switch is recessed behind the faceplate to avoid accidental disturbance. It is not for customer use.

STM-1 port

Reset switch

14271

LED Indicators

Table 1-5 describes the LEDs on the faceplate of the NTC STM-1.

1-16 Cisco 6200 User Guide

1.3.6 NTC STM-1 Speci???cations

Table 1-6 lists the physical and electrical speci???cations of the NTC STM-1.

1.4 Management Processor Card (MPC)

The Cisco 6200 is controlled and managed by the MPC.

1.4.1 Functional Description

The MPC performs management and storage tasks for the Cisco 6200 DSLAM. The MPC provides

???The Cisco IOS command line interface (CLI) for con???guration and monitoring

???An SNMP agent for communicating between the Cisco 6200 and the PC running the Cisco 6200 Manager software

???Alarm contacts and environmental monitoring of key system resources

???Line card con???guration and fault polling

???Nonvolatile storage of con???guration information

???Two PCMCIA Flash slots for storage of software images and con???guration data

1-18 Cisco 6200 User Guide

The MPC runs a version of Cisco IOS software that is designed for DSL multiplexing.

At startup, the MPC loads program software and con???guration data from NVRAM, from a server on the network, or from a Flash card in one of its PCMCIA slots. The MPC then provides boot images to the line cards. After initializing the system, the MPC provides monitoring and control services, including the CLI (available at the console and via Telnet); SNMP communication with the Cisco 6200 Manager; and critical, major, and minor alarm signals.

1.4.2 Physical Description

The MPC resides in slot 2. The MPC faceplate (see Figure 1-9) includes the ???xtures discussed in the following paragraphs.

MPC

POWER

READYCard status LEDs

ACTIVE

ACO Alarm cut-off switch

ALARMS

CRIT

MAJAlarm LEDs

MIN

C

NConsole port

S

L

SLOT

0 1

Two PCMCIA slots

PCMCIA ejection buttons

LINK

ACTV

E

NEthernet port

E

T

Reset switch

11948

ACO Switch

The alarm cut-off (ACO) switch is a pushbutton located near the top of the MPC. Press the switch to turn off an audible alarm. (For more information on alarms, see the ???Alarm Relay Connection??? section on page 1-5.)

Console Port

The console port on the MPC is a serial EIA/TIA-232 port with an RJ-45 connector. See Appendix A, ???Pin Assignments,??? for pinouts.

PCMCIA Slots and Ejection Buttons

The MPC provides two slots for PCMCIA Flash memory cards. PCMCIA cards store system software and node con???guration information. An ejection button is located beneath each PCMCIA slot; push the button to remove the card.

Ethernet Port

The Ethernet port on the MPC is a 10BaseT port with an RJ-45 connector. It is used to connect the Cisco 6200 to its management station. See Appendix A, ???Pin Assignments,??? for pinouts.

Reset Switch

The reset switch, which initializes the MPC, is recessed behind the faceplate to avoid accidental disturbance.

LED Indicators

All LEDs on the MPC are described in Table 1-7.

1-20 Cisco 6200 User Guide

78-5296-02 10/02/98Hardware Description 1

1.4.3 MPC Speci???cations

Table 1-8 lists the physical and electrical speci???cations of the MPC.

1.5 Subscriber Line Card (SLC)

This section describes the CAP and DMT versions of the subscriber line card (SLC). A Cisco 6200 chassis can hold up to 10 SLC modules.

Note All the SLCs in a Cisco 6200 chassis should be of the same type. The mixture of CAP and

DMT cards in a single chassis is not supported.

1.5.1 What is the SLC 8CAP?

The CAP version of the SLC (labeled SLC 8CAP) is a hot-swappable line module that provides data communication between the Cisco 6200 node and up to eight subscribers. Modems on the CAP SLC use the carrierless amplitude modulation/phase modulation (CAP) method, a common line code method for asymmetric digital subscriber line (ADSL) transmissions. As an ADSL device, the CAP SLC transmits high-speed data through an external plain old telephone service (POTS) splitter to subscribers over existing, telephone-grade segments of copper wire. Figure 1-10 illustrates SLC operation.

The CAP SLC transports data at speeds up to 7 Mbps downstream (from the service provider to the subscriber) and receives up to 1 Mbps upstream (from the subscriber to the service provider). The SLC supports upstream and downstream passband channels for subscriber data. Baseband POTS is unused by the SLC; data is added to this channel by the external POTS splitter.

How the SLC Handles Traf???c

In the downstream direction, the SLC receives ATM cells from the Cisco 6200 backplane bus. The cell ???lter discards cells whose virtual path/virtual channel IDs (VPI/VCIs) do not pertain to this subscriber???s channel. (Each port has a ???xed set of 31 VCIs, which are permanently assigned to VCIs on the NTC.) The traf???c controller buffers cells. Then the CAP transceiver transmits the outbound cells. The SLC sends the cells out to an external POTS splitter, which inserts baseband POTS traf???c (if any such traf???c is provided) before sending the downstream ADSL and POTS signals across standard unshielded twisted pair copper wire to the subscriber.

In the upstream direction, the SLC receives ADSL signals from a POTS splitter and demodulates the CAP-modulated signal. Then the SLC channel contends with the other SLC channels for the upstream data bus. Two priority levels are available. For the ???rst Cisco 6200 release, only UBR service is available. The SLC will ensure fair access among all cells of the same priority.

The SLC separates the upstream and downstream data channels:

At the subscriber site, the DSL customer premises equipment (the Cisco 675, for example) demodulates the downstream signal and sends the data to the subscriber???s PC.

Transmission Rates and Modem Training

Two options are available with respect to transmission rates:

???You can set the subscriber ports to rate-adapt (train) automatically to the highest attainable line speed.

???You can set transmission speeds. Upstream and downstream speeds can be set separately.

1-22 Cisco 6200 User Guide

In the downstream direction, 11 rates are available ranging from 640 kbps to 7.168 Mbps. In the upstream direction, 9 rates are available, ranging from 91 kbps to 1.088 Mbps.

The modems on the CAP SLC train in sequence, ???rst downstream, then upstream. Each modem ???rst acquires the line. Then it tests the signal quality on the line by measuring the signal-to-noise ratio (SNR). It adds a preset margin, 6 dbm, to the SNR, and compares the resulting value to a table. If the value is acceptable, the modem trains at the con???gured rate. If not, the modem repeats the process, using the next lower transmission rate. The modem keeps trying to train inde???nitely until it is successful.

Statistics

The SLC gathers signal quality statistics for network management purposes. It sends this information to the management system via the master SNMP agent. The SLC reports each of the following statistics to the management system for both upstream and downstream traf???c:

???Number of nonidle cells transmitted downstream

???Number of nonidle upstream cells received with valid header checksum

???Number of upstream cells received with invalid header checksum

???Number of errored seconds (this is the number of seconds in which at least one header checksum error or loss of cell delineation is observed), both upstream and downstream

Figure 1-10 SLC 8CAP Operation

Public telephone network

Cisco

1.5.2 SLC 8CAP: Physical Description

Up to 10 SLCs can be installed in a Cisco 6200 cabinet. The cabinet slots assigned to the SLCs are slot 5 through slot 14.

The CAP SLC???s faceplate is labeled SCL 8CAP. The faceplate (Figure 1-11) includes the ???xtures discussed in the following paragraphs.

Reset Switch

The reset switch is recessed behind the faceplate to avoid accidental activation. It is not for customer use.

LED Indicators

Table 1-9 describes the LEDs on the faceplate of the SLC.

Figure 1-11 SLC 8CAP Faceplate

Reset switch

11947

1-24 Cisco 6200 User Guide

1.5.3 SLC 8CAP Speci???cations

Table 1-10 lists the physical and electrical speci???cations of the CAP SLC (SLC 8CAP).

1-26 Cisco 6200 User Guide

1.5.4 What is the SLC 8DMT?

The eight-port DMT version of the SLC (SLC 8DMT) is a hot-swappable line module that provides data communication between the Cisco 6200 node and up to eight subscribers. Modems on the SLC 8DMT use discrete multitone (DMT) modulation, a common method for encoding asymmetric digital subscriber line (ADSL) transmissions. The SLC 8DMT transmits high-speed data through an external POTS splitter to subscribers over existing, telephone-grade segments of copper wire. Figure 1-12 illustrates SLC operation.

Figure 1-12 SLC 8DMT Operation

Public telephone network

Cisco

The SLC 8DMT transports data at speeds up to 8 Mbps downstream (from the service provider to the subscriber) and receives at speeds up to 800 kbps upstream (from the subscriber to the service provider). The SLC supports upstream and downstream passband channels for subscriber data.

Baseband plain old telephone service (POTS) is unused by the SLC; voice and data are added by the external POTS splitter.

How the SLC 8DMT Handles Traf???c

In the downstream direction, the SLC receives ATM cells from the Cisco 6200 backplane bus. The cell ???lter discards cells whose virtual path/virtual channel IDs (VPI/VCIs) do not pertain to a particular subscriber???s channel. (Each port has a ???xed set of 31 VCIs, numbered 33 to 63, which are permanently assigned to VCIs on the NTC.) The cell ???lter buffers cells, and the DMT transceiver transmits the outbound cells. The SLC sends the cells out to an external POTS splitter, which inserts baseband POTS traf???c (if any such traf???c is provided) before sending the downstream ADSL and POTS signals across standard unshielded twisted pair copper wire to the subscriber.

In the upstream direction, the SLC receives ADSL signals from a POTS splitter and demodulates the DMT-modulated signal. Then the SLC channel contends with the other SLC channels for the upstream data bus. Two priority levels are available. For the ???rst Cisco 6200 release, only UBR service is available. The SLC will ensure fair access among all cells of the same priority.

The SLC separates the upstream and downstream data channels:

At the subscriber site, the DSL customer premises equipment (CPE)???the Cisco 676, for example??? demodulates the downstream signal and sends the data to the subscriber???s PC.

Transmission Rates and Modem Training

Two modes are available for setting transmission rates:

???Rate-adaptive mode: You can set the subscriber ports to adapt (train) automatically to the highest line speed attainable for the con???gured signal-to-noise ratio (SNR) margin for each direction.

???Explicit rate mode: You can set SNR margins and transmission speeds explicitly. Upstream and downstream speeds can be set separately.

You can mix rate-adaptive and explicit modes on the same circuit, using one mode for upstream traf???c and the other for downstream traf???c.

Rates available for downstream traf???c range from 32 kbps to 8.032 Mbps, in increments of 32 kb (32 kbps, 64 kbps, 96 kbps, 128 kbps, and so on). Rates available for upstream traf???c start at 32 kbps and increase in 32-kb increments to a maximum upstream rate of 864 kbps.

The modems on the SLC 8DMT train simultaneously in the upstream and downstream directions. Each modem ???rst tries to train at the con???gured rate at a speci???ed SNR margin. If the ???rst attempt fails in either direction but a CPE is detected, the modem tries to train at the highest rate possible (up to the con???gured rate). The modem keeps trying to train until it is successful.

Statistics

The SLC 8DMT gathers signal quality statistics for network management purposes and sends this information to the management system via SNMP. The SLC reports each of the following statistics to the management system for both upstream and downstream traf???c:

1-28 Cisco 6200 User Guide

???Number of upstream cells received with invalid header checksum

???Number of errored seconds (this is the number of seconds in which at least one DMT-layer CRC error, loss of signal, or severely errored frame is observed), both upstream and downstream

In addition, the SLC 8DMT reports the following fault indications:

1.5.5 SLC 8DMT: Physical Description

Up to ten SLCs can be installed in a Cisco 6200 cabinet. The slots assigned to the SLCs are slot 5 through slot 14.

The card???s faceplate is labeled SLC 8DMT. The faceplate (Figure 1-13) includes a reset switch and LED indicators.

Reset switch

13067

Reset Switch

The reset switch is recessed behind the faceplate to avoid accidental activation. It is not for customer use.

LED Indicators

Table 1-11 describes the LEDs on the faceplate of the SLC.

1-30 Cisco 6200 User Guide

1.5.6 SLC 8DMT Speci???cations

Table 1-12 lists the physical and electrical speci???cations of the SLC 8DMT.

1-32 Cisco 6200 User Guide