Cisco_Systems_Server

1 Overview

This guide is designed to help you quickly set up and use your Cisco 1040 Sensor (Cisco 1040). A Cisco 1040 is a shelf-top unit that connects to the network and obtains Power over Ethernet (PoE) through a Cisco Catalyst switch. It is easy to connect your Cisco 1040. These sections explain what a Cisco 1040 does and how it fits in with products in the Cisco Unified Communications Management Suite:

???Cisco 1040s and Cisco Unified Service Monitor, page 2

???Cisco 1040s and Cisco Unified Operations Manager, page 2

Cisco 1040s and Cisco Unified Service Monitor

Cisco 1040s listen to Real-Time Transport Protocol (RTP) voice traffic on a Switch Port Analyzer (SPAN) port that you must configure to mirror voice traffic on phone ports or voice VLANs. Cisco 1040 calculates Mean Opinion Scores (MOS) and sends data at 60-second intervals to Cisco Unified Service Monitor (Service Monitor), a product from the Cisco Unified Communications Management Suite.

Service Monitor examines the MOS value and compares it against a user-specified threshold value for the codec in use on the call. When MOS drops below the threshold, Service Monitor generates SNMP traps and sends them to up to four recipients. A single Service Monitor can receive and analyze MOS data from multiple Cisco 1040s. If you have more than one Service Monitor, you can configure Cisco 1040s to fail over to a secondary service monitor. For more information, see User Guide for Cisco Unified Service Monitor.

Cisco 1040s and Cisco Unified Operations Manager

You can use Cisco Unified Operations Manager (Operations Manager) to further analyze, display, and act on the traps that Cisco 1040 generates. When configured as a trap recipient from Service Monitor, Operations Manager generates service quality events, displays and tracks these events on a real-time dashboard, and displays and stores event history. You can configure additional event settings on Operations Manager that alert you to low MOS and to the occurrence of many service quality events during a period of time. In addition, you can configure Operations Manager to send notifications by e-mail, SNMP trap, and syslog message.

2 Preparing to Connect Your Cisco 1040

This section describes tasks that you must perform the first time you set up your network to support Cisco 1040 operations. If you have not already completed the following tasks, it is advisable to complete them so that your Cisco 1040 becomes fully operational minutes after you connect it.

Install and Configure Cisco Unified Service Monitor

Instructions for completing these tasks are available in User Guide for Cisco Unified Service Monitor and in Service Monitor online help. Using Service Monitor, perform the following tasks:

???Set up Service Monitor. Among other parameters, you will specify a TFTP server.

???Edit configuration files for Cisco 1040s.

Configure DHCP Server Option 150

Configure your DHCP server so that option 150 returns the IP address for the TFTP server and provides an IP address, subnet mask, default gateway, and, optionally, a DNS server for a Cisco 1040.

If you would like to configure a Cisco router as a DHCP server, see the following URL.

http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080114aee.shtml

(Optional) Configure DNS

If you are using DNS in your network, configure DNS entries for Cisco 1040s.

3 Connecting Your Cisco 1040

Note Be sure to read the ???Regulatory Compliance and Safety Information for Your Cisco 1040??? section on page 13 before connecting your Cisco 1040.

Figure 1 shows the connections and indicators on the front panel of your Cisco 1040.

Figure 1 Cisco 1040 Cable Connections???Front Panel

1 2

10/100-1 10/100-2

Note This port does not support Cisco prestandard PoE.

210/100-2???Fast Ethernet port, standard RJ45 ??? ??? for connecting to a SPAN or Remote SPAN (RSPAN) destination port.

Figure 2 shows the connection on the rear panel of your Cisco 1040 for an external, separately certified AC/DC power supply, for use if IEEE 802.3af-compliant PoE is not available. See Cable Specifications, page 12.

Figure 2 Cisco 1040 Cable Connections???Rear Panel

POWER

DC 5V 2.5A

141284

Cisco 1040 Port Usage

This section provides a list of ports used by the Cisco 1040, for your reference.

Selecting and Configuring a Cisco Catalyst Switch

To connect the Cisco 1040, you need a Cisco Catalyst switch with the following:

???A port that supports IEEE 802.3af standard Power over Ethernet (PoE).

???A port that is configured as a SPAN or RSPAN destination port for:

???Ports to which phones are connected

???VLANs

For information about configuring SPAN and RSPAN on Cisco Catalyst switches and modules, see the following URL.

http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015c612. shtml

Connecting the Cisco 1040 to the Cisco Catalyst Switch

Before you begin this procedure, see the regulatory compliance and safety information Statement 1001???Work During Lightning Activity, page 23.

Step 1 Place the Cisco 1040 on top of the appropriate Cisco Catalyst switch.

Note The minimum height necessary to install the Cisco 1040 is 5.08 cm (2 in.). The installation of the unit should not restrict the airflow around the device. When operating the unit, ensure that no objects are placed on top of the unit.

Step 2 Connect a Category 5 straight-through cable from 10/100-1 (Fast Ethernet port 1) on the Cisco 1040 to a port that supports IEEE 802.3af standard PoE on the Cisco Catalyst switch.

Step 3 Connect a Category 5 straight-through cable from 10/100-2 (Fast Ethernet port 2) on the Cisco 1040 to a port that you have configured as a SPAN (or RSPAN) destination port on the Cisco Catalyst switch.

Note Verify that this port on the switch is set up to mirror a VLAN or switch ports to which phones are connected.

A startup process begins on the Cisco 1040. The status indicator on the front of the Cisco 1040 should flash amber, turn yellow, and then turn green. For more information, see Understanding the Status Indicator Light, page 7.

4 Using Your Cisco 1040

After you have successfully connected your Cisco 1040, use Service Monitor to manage and configure it. For example, you will use Service Monitor to specify the TFTP server to use, update configuration files, set the time, and reset Cisco 1040s.

This section describes information that you can obtain directly from a Cisco 1040:

???Understanding the Status Indicator Light, page 7

???Using the Cisco 1040 Web Interface, page 8

Note Information obtained directly from a Cisco 1040 is also available in another form from Service Monitor. Service Monitor displays the status of Cisco 1040s.

Using the Cisco 1040 Web Interface

You can open a web interface to view information stored on a Cisco 1040 as follows.

Step 1 In your browser, enter http://<IP address or DNS name> where IP address is the address of your Cisco 1040 and DNS name is the DNS name for the Cisco 1040. For example:

http://Cisco-1040-sj

The Device Information window displays the following information:

???ID???Cisco 1040 ID.

???MAC Address???Cisco 1040 MAC address.

???Time stamp???Current time on the Cisco 1040.

???Status???Status of the Cisco 1040; one of the following:

???operational???Cisco 1040 is receiving RTP streams, analyzing the data, and sending syslog messages when required.

???not communicating with receiver???The Service Monitor is unreachable.

???Current Service Monitor???IP address or DNS name of the service monitor to which the Cisco 1040 is registered; this could be the primary or secondary service monitor.

???TFTP IP Address???IP address of the TFTP server from which the Cisco 1040 obtains a configuration file and binary image file.

???Switch IP Address???Switch that this Cisco 1040 is connected to.

???Switch Port???Switch port that this Cisco 1040 is connected to.

???Software Version???Name of the binary image file installed on the Cisco 1040.

???Last Updated???The last time that the configuration for the Cisco 1040 was updated.

Step 2 To view the contents of the configuration file on the TFTP server for this Cisco 1040, enter http://<IP address or DNS name>/Communication where IP address is the address of your Cisco 1040 and DNS name is the DNS name for the Cisco 1040. For example:

http://Cisco-1040-sj/Communication

The Communication Log File window displays the following information, which is stored in the configuration file on the TFTP server:

???Receiver???IP address or DNS name of each Service Monitor defined in the configuration file???primary or secondary???separated by semicolons.

???ID???ID of the Cisco 1040 that uses this configuration file.

???Image???Name of the binary image file that the Cisco 1040 should download and run from the TFTP server.

???Last Updated???The last time that this configuration file was updated on the Service Monitor system.

???CDPGlobalRunState???States whether CDP is enabled (true) or disabled (false).

???SyslogPort???States the port protocol (UDP) and port number used for sending syslogs to Service Monitor.

???SkinnyPort???States the port protocol (TCP) and port number used to communicate with Service Monitor.

5 Where to Go Next

After you have performed first time installation tasks and connected a Cisco 1040, Cisco 1040 starts listening to RTP traffic and sending MOS data to Service Monitor. For more information, see the following User Guides for Cisco Unified Communications Management Suite applications:

???User Guide for Cisco Unified Service Monitor

???User Guide for Cisco Unified Operations Manager

You can access these documents:

???In PDF in the Documentation directory on the respective product CD-ROM.

???In HTML and PDF on Cisco.com. From Cisco.com:

a.Enter the URL, http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/index.htm

b.Select the appropriate application.

c.Select appropriate application version.

d.Select User Guide.

???From the CiscoWorks Online help:

a.From the CiscoWorks Homepage, click Help.

b.Select the appropriate Cisco Unified Communications Management Suite application.

6 Related Documentation

Note Although every effort has been made to validate the accuracy of the information in the printed and electronic documentation, updates are sometimes necessary. Any changes to the original publications are reflected on Cisco.com, where you will find the most up-to-date documentation.

For information about configuring SPAN and RSPAN ports on Cisco Catalyst switches, see the software configuration guide for the appropriate switch model and Cisco IOS version. Use this procedure to locate software configuration guides for Cisco Catalyst switches.

Step 1 Log into Cisco.com at http://www.cisco.com.

Step 2 Select Technical Support & Documentation > Documentation.

Step 3 Select Switches.

Step 4 Select the appropriate model Cisco Catalyst switch.

Step 5 Select Configuration Guides.

Step 6 Select the software configuration guide for the Cisco Catalyst switch model and Cisco IOS version that is running on the switch.

For information about installing, troubleshooting, and using the applications related to Cisco 1040 see Table 2.

Note To view documents in Adobe Portable Document Format (PDF), Adobe Acrobat 4.0 or later is required. To view documents on Cisco.com, log on to your Cisco.com home page, then enter the URL, http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/index.htm.

Physical and Operating Environment Specifications

Cable Specifications

???RJ-45 jack for the LAN 10/100BaseT connection (10/100-1)

???RJ-45 jack for the second LAN 10/100BaseT compliant connection (10/100-2)

Caution External AC/DC Power Supply Specification: You must use a separately certified AC-to-DC Power Supply. This Power Supply must be rated: 5vDC 2.5A certified and marked: Limited Power Source (or L.P.S.).

Network Port Pinouts

Pin Number Function

7CTS???Clear to send

8RTS???Request to send

8 Regulatory Compliance and Safety Information for Your Cisco 1040

Caution

If the Cisco 1040 is used in a manner not specified by Cisco, the protection provided in the equipment might be impaired.

Inline power circuits provide current through the communication cable. Use the Cisco-provided cable or a minimum 24 AWG communication cable (for example, CAT 5, 24 AWG).

The Cisco 1040 has no operator-serviceable parts inside.

Regulatory compliance and safety information for Cisco 1040 includes the following sections:

???Warning Definition???Statement 1071, page 14

???Translated Warnings, page 21

???European Directives, page 40

???Regulatory Standards Compliance, page 42

???EMC Environmental Conditions for Products Installed in the European Union, page 43

???EMC Class B Notices and Warnings, page 43

Warning Definition???Statement 1071

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus T??RKEIT?? TURVALLISUUSOHJEITA

T??m?? varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin k??sittelet laitteistoa, huomioi s??hk??piirien k??sittelemiseen liittyv??t riskit ja tutustu onnettomuuksien yleisiin ehk??isytapoihin. Turvallisuusvaroitusten k????nn??kset l??ytyv??t laitteen mukana toimitettujen k????nnettyjen turvallisuusvaroitusten joukosta varoitusten lopussa n??kyvien lausuntonumeroiden avulla.

S??ILYT?? N??M?? OHJEET

Attention IMPORTANTES INFORMATIONS DE S??CURIT??

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entra??ner des blessures ou des dommages corporels. Avant de travailler sur un ??quipement, soyez conscient des dangers li??s aux circuits ??lectriques et familiarisez-vous avec les proc??dures couramment utilis??es pour ??viter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de s??curit?? traduites qui accompagnent cet appareil, r??f??rez-vous au num??ro de l'instruction situ?? ?? la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen f??hren kann. Machen Sie sich vor der Arbeit mit Ger??ten mit den Gefahren elektrischer Schaltungen und den ??blichen Verfahren zur Vorbeugung vor Unf??llen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen ??bersetzung in den ??bersetzten Sicherheitshinweisen, die zusammen mit diesem Ger??t ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan f??re til skade p?? person. F??r du begynner ?? arbeide med noe av utstyret, m?? du v??re oppmerksom p?? farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for ?? forhindre ulykker. Bruk nummeret i slutten av hver advarsel for ?? finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE P?? DISSE INSTRUKSJONENE

Aviso INSTRU????ES IMPORTANTES DE SEGURAN??A

Este s??mbolo de aviso significa perigo. Voc?? est?? em uma situa????o que poder?? ser causadora de les??es corporais. Antes de iniciar a utiliza????o de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos el??tricos e familiarize-se com as pr??ticas habituais de preven????o de acidentes. Utilize o n??mero da instru????o fornecido ao final de cada aviso para localizar sua tradu????o nos avisos de seguran??a traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRU????ES

??Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este s??mbolo de aviso indica peligro. Existe riesgo para su integridad f??sica. Antes de manipular cualquier equipo, considere los riesgos de la corriente el??ctrica y familiar??cese con los procedimientos est??ndar de prevenci??n de accidentes. Al final de cada advertencia encontrar?? el n??mero que le ayudar?? a encontrar el texto traducido en el apartado de traducciones que acompa??a a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA S??KERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf??r arbete p?? n??gon utrustning m??ste du vara medveten om farorna med elkretsar och k??nna till vanliga f??rfaranden f??r att f??rebygga olyckor. Anv??nd det nummer som finns i slutet av varje varning f??r att hitta dess ??vers??ttning i de ??versatta s??kerhetsvarningar som medf??ljer denna anordning.

SPARA DESSA ANVISNINGAR

Statement 1001???Work During Lightning Activity

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Waarschuwing Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.

Varoitus ??l?? ty??skentele j??rjestelm??n parissa ??l??k?? yhdist?? tai irrota kaapeleita ukkosilmalla.

Attention Ne pas travailler sur le syst??me ni brancher ou d??brancher les c??bles pendant un orage.

Warnung Arbeiten Sie nicht am System und schlie??en Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.

Avvertenza Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.

Advarsel Utf??r aldri arbeid p?? systemet, eller koble kabler til eller fra systemet n??r det tordner eller lyner.

Aviso N??o trabalhe no sistema ou ligue e desligue cabos durante per??odos de mau tempo (trovoada).

??Advertencia! No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas el??ctricas en la atm??sfera.

Varning! Vid ??ska skall du aldrig utf??ra arbete p?? systemet eller ansluta eller koppla loss kablar.

Statement 1021???SELV Circuit

Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021

Waarschuwing Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt.

Varoitus Jotta v??ltyt s??hk??iskulta, ??l?? kytke pienj??nnitteisi?? SELV-suojapiirej?? puhelinverkkoj??nnitett?? (TNV) k??ytt??viin virtapiireihin. LAN-portit sis??lt??v??t SELV-piirej?? ja WAN-portit puhelinverkkoj??nnitett?? k??ytt??vi?? piirej??. Osa sek?? LAN- ett?? WAN-porteista k??ytt???? RJ-45-liittimi??. Ole varovainen kytkiess??si kaapeleita.

Attention Pour ??viter une ??lectrocution, ne raccordez pas les circuits de s??curit?? basse tension (Safety Extra-Low Voltage ou SELV) ?? des circuits de tension de r??seau t??l??phonique (Telephone Network Voltage ou TNV). Les ports du r??seau local (LAN) contiennent des circuits SELV et les ports du r??seau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les c??bles en prenant toutes les pr??cautions n??cessaires.

Warnung Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschlie??en. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschlie??en von Kabeln.

Avvertenza Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi.

Advarsel Unng?? ?? koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unng??r elektrisk st??t. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes b??de LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. V??r forsiktig n??r du kobler kabler.

Aviso Para evitar choques el??ctricos, n??o conecte os circuitos de seguran??a de baixa tens??o (SELV) aos circuitos de tens??o de rede telef??nica (TNV). As portas LAN cont??m circuitos SELV e as portas WAN cont??m circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos.

??Advertencia! Para evitar la sacudida el??ctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telef??nica (telephone network voltage = TNV). Los puertos de redes de ??rea local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de ??rea extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precauci??n al conectar los cables.

Varning! F??r att undvika elektriska st??tar, koppla inte s??kerhetskretsar med extra l??g sp??nning (SELV-kretsar) till kretsar med telefonn??tsp??nning (TNV-kretsar). LAN-portar inneh??ller SELV-kretsar och WAN-portar inneh??ller TNV-kretsar. Vissa LAN- och WAN-portar ??r f??rsedda med RJ-45-kontakter. Iaktta f??rsiktighet vid anslutning av kablar.

Statement 1074???Comply with Local and National Electrical Codes

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.

Varoitus Laitteisto tulee asentaa paikallisten ja kansallisten s??hk??m????r??ysten mukaisesti.

Attention L'??quipement doit ??tre install?? conform??ment aux normes ??lectriques nationales et locales.

Warnung Die Installation der Ger??te muss den Sicherheitsstandards entsprechen.

Avvertenza L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.

Advarsel Installasjon av utstyret m?? samsvare med lokale og nasjonale elektrisitetsforskrifter.

Aviso A instala????o do equipamento tem de estar em conformidade com os c??digos el??ctricos locais e nacionais.

??Advertencia! La instalaci??n del equipo debe cumplir con las normativas de electricidad locales y nacionales.

Varning! Installation av utrustningen m??ste ske i enlighet med g??llande elinstallationsf??reskrifter.

Statement 1040???Product Disposal

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Waarschuwing Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.

Varoitus T??m?? tuote on h??vitett??v?? kansallisten lakien ja m????r??ysten mukaisesti.

Attention La mise au rebut ou le recyclage de ce produit sont g??n??ralement soumis ?? des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr??s de l'organisme comp??tent.

Warnung Die Entsorgung dieses Produkts sollte gem???? allen Bestimmungen und Gesetzen des Landes erfolgen.

Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.

Advarsel Endelig kassering av dette produktet skal v??re i henhold til alle relevante nasjonale lover og bestemmelser.

Aviso Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.

??Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.

Statement 353???This Product Must be Connected

Warning This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source.

Statement 353

Waarschuwing Dit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE (power-over-ethernet) IEEE 802.3af of een beperkte stroomvoorziening die compatibel is met IEC60950.

Varoitus T??m?? tuote on liitett??v?? PoE (power-over-ethernet) IEEE 802.3af -yhteensopivaan virtal??hteeseen tai IEC60950-yhteensopivaan rajoitettuun virtal??hteeseen.

Attention Ce produit doit ??tre connect?? ?? une source d'alimentation ??lectrique par c??ble Ethernet (PoE) conforme ?? la norme IEEE 802.3af ou ?? une source d'alimentation limit??e conforme ?? la norme IEC60950.

Warnung Dieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE 802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle f??r geringe Leistungen, die IEC60950-kompatibel ist.

Avvertenza Questo prodotto deve essere connesso a una fonte di alimentazione di tipo PoE (power-over-ethernet) conforme a IEEE 802.3af o a una fonte di alimentazione conforme a IEC60950.

Advarsel Dette produktet m?? v??re koblet til en Power-over-Ethernet (PoE) IEEE 802.3af-kompatibel str??mkilde eller en IEC60950-kompatibel begrenset str??mkilde.

Aviso Este produto tem de estar ligado a uma fonte de alimenta????o compat??vel com a norma IEEE 802.3af, tamb??m conhecida pela sigla Power over Ethernet (PoE), ou a uma fonte de alimenta????o limitada compat??vel com a norma IEC60950.

??Advertencia! Debe conectar este producto a una fuente de alimentaci??n sobre ethernet (PoE) conforme con el est??ndar IEEE 802.3af, o a una fuente limitada conforme con el est??ndar IEC60950.

Varning! Denna produkt m??ste vara ansluten till en PoE IEEE 802.3af-kompatibel str??mk??lla eller en IEC60950-kompatibel begr??nsad str??mk??lla.

??Advertencia! El equipo est?? dise??ado para trabajar con sistemas de alimentaci??n tipo TN.

Varning! Enheten ??r konstruerad f??r anv??ndning tillsammans med elkraftssystem av TN-typ.

Statement 331???Power Supply Installation Warning

Warning The power supply must be placed indoors. Statement 331

Waarschuwing De stroomtoevoer moet binnen worden geplaatst.

Varoitus Tehonl??hde on sijoitettava sis??tiloihin.

Attention Le bloc d???alimentation ??lectrique doit ??tre plac?? ?? l???int??rieur.

Warnung Die Stromversorgungsquelle darf nicht im Freien aufgestellt werden.

Avvertenza L???alimentatore deve essere posto in un luogo interno.

Advarsel Str??mkilden skal v??re plassert innend??rs.

Aviso A fonte de alimenta????o deve ser instalada no interior.

Statement 1005???Circuit Breaker

Warning This product relies on the building???s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

120 VAC, 15A (U.S./CAN); 240 VAC, 10A (INTERNATIONAL) Statement 1005

Waarschuwing Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan:

120 VAC, 15A (U.S./CAN); 240 VAC, 10A (INTERNATIONAL) is.

Varoitus T??m?? tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, ett?? suojalaitteen mitoitus ei ole yli: