Catalyst GigaStack Gigabit

Interface Converter Hardware

Installation Guide

March 2002

Corporate Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706

USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 526-4100

Customer Order Number: DOC-786460=

Text Part Number: 78-6460-04

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT

NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT

ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR

THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION

PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO

LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco???s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco???s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

???Turn the television or radio antenna until the interference stops.

???Move the equipment to one side or the other of the television or radio.

???Move the equipment farther away from the television or radio.

???Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB???s public domain version of the UNIX operating system. All rights reserved. Copyright ?? 1981, Regents of the University of Calif ornia.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE

PROVIDED ???AS IS??? WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL

DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR

INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Copyright ?? 1999 ???2002, Cisco Systems, Inc.

All rights reserved.

C O N T E N T S

Contents

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Contents

I N D E X

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Contents

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Cisco Limited Lifetime Hardware

Warranty Terms

There are special terms applicable to your hardware warranty as well as services you may use during the warranty period. Your formal Warranty Statement, including the warranty applicable to Cisco software, appears in the CD which accompanies your Cisco Product. Follow these steps to access and download the Cisco Information Packet and your warranty document from the CD or from Cisco.com.

1.Launch your browser and go to the following URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm The Warranties and License Agreement page appears.

2.To view the Cisco Information Packet, perform these steps:

a.Click the Information Packet Number field and make sure that the part number 78-5235-02C0 is highlighted.

b.Select the language to view the document.

c.Click Go. The Information Packet page appears.

d.From this page you can review the document online or click the PDF icon to download and print the document in Adobe Portable Data File (PDF) format.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Cisco Limited Lifetime Hardware Warranty Terms

Note You must have Adobe Acrobat Reader in order to view and print a PDF file. If you do not have the viewer, click the Get Acrobat Reader icon at the bottom of the page to go to the Adobe.com website and download the reader.

3.To view translated and/or localized warranty information about your product, follow these steps:

a.Enter the following part number in the Warranty Document Number field:

78-6310-02C0

b.Select the language to view the document.

c.Click Go. The Cisco Warranty page appears.

From this page you can review the document online or click the PDF icon to download and print the document in Adobe Portable Data File (PDF) format.

You may also contact our Service and Support website for assistance at:

http://www.cisco.com/public/Support_root.shtml.

Duration of Hardware Warranty

As long as the original End User continues to own or use the Product, provided that: fan and power supply warranty is limited to five (5) years. In the event of discontinuance of product manufacture, Cisco warranty support is limited to five

(5) years from the announcement of discontinuance.

Replacement, Repair or Refund Procedure for Hardware

Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of the RMA request. Actual delivery times may vary depending on Customer location.

Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.

To Receive a Return Materials Authorization (RMA) Number

Please contact the party from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Cisco Limited Lifetime Hardware Warranty Terms

Complete the information below and keep for ready reference.

Product purchased from:

Their telephone number:

Product Model and Serial number:

Maintenance Contract number:

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Cisco Limited Lifetime Hardware Warranty Terms

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Audience

This guide is for the technician installing the GigaStack Gigabit Interface Converter (GBIC), hereafter referred to as the GigaStack GBIC. Before using this guide, make sure that you are familiar with the concepts and terminology of Ethernet and local-area networking.

Purpose

This guide describes how to install the GigaStack GBIC and troubleshoot problems associated with its installation.

Note The GigaStack GBICs and their ports are managed through one of the management interfaces of a Gigabit-capable switch. For more information about managing GigaStack GBICs, refer to the software configuration guides for the Catalyst 2900 series XL, the Catalyst 2950, the Catalyst 3500 series XL, and the Catalyst 3550 multilayer switches.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Organization

Organization

This guide is organized into the following chapters:

Chapter 1, ???Overview,??? describes the key features, provides a physical description, and shows how the GigaStack GBICs can be deployed in real networks.

Chapter 2, ???Installation,??? explains how to install the GigaStack GBIC.

Chapter 3, ???Troubleshooting,??? describes how to identify and resolve common installation and cabling problems.

Appendix A, ???Technical Specifications,??? lists the physical and environmental specifications and the regulatory agency approvals.

Appendix B, ???Connectors and Cables,??? describes the cables and connectors that can connect to the GigaStack GBIC ports.

Appendix C, ???Translated Safety Warnings,??? contains translations of the warnings in this guide.

Notes, Cautions, and Warnings

Notes, cautions, and warnings use the following conventions and symbols:

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Notes, Cautions, and Warnings

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with the standard practices for preventing accidents. The warning symbol also means that you can see the warning in multiple languages in ???Appendix C, ???Translated Safety Warnings.???

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Het waarschuwingssymbool betekent ook dat u de waarschuwing in meerdere talen in Appendix C, ???Translated Safety Warnings??? kunt vinden.

Varoitus T??m?? varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin ty??skentelet mink????n laitteiston parissa, ota selv???? s??hk??kytkent??ihin liittyvist?? vaaroista ja tavanomaisista onnettomuuksien ehk??isykeinoista. Varoitusmerkki tarkoittaa my??s sit??, ett?? varoitus esiintyy useilla kielill?? osassa Appendix C, ???Translated Safety Warnings.???

Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un ??quipement, soyez conscient des dangers pos??s par les circuits ??lectriques et familiarisez-vous avec les proc??dures couramment utilis??es pour ??viter les accidents. Le symbole d'avertissement signifie ??galement que cet avis se trouve traduit dans plusieurs langues dans la section ??Appendix C, ???Translated Safety Warnings?????.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Notes, Cautions, and Warnings

Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer

Situation, die zu einer K??rperverletzung f??hren k??nnte. Bevor Sie mit der Arbeit an irgendeinem Ger??t beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unf??llen bewu??t. Das Warnsymbol bedeutet auch, da?? Sie die Warnung in verschiedenen Sprachen unter Appendix C, ???Translated Safety Warnings??? lesen k??nnen.

Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. Il simbolo di avvertenza indica inoltre che l???avvertenza viene presentata in diverse lingue in Appendix C, ???Translated Safety Warnings.???

Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan f??re til personskade. F??r du utf??rer arbeid p?? utstyr, m?? du vare oppmerksom p?? de faremomentene som elektriske kretser inneb??rer, samt gj??re deg kjent med vanlig praksis n??r det gjelder ?? unng?? ulykker. Dette varselsymbolet betyr ogs?? at du kan lese advarselen p?? flere spr??k i ??Appendix C, ???Translated Safety Warnings?????.

Aviso Este s??mbolo de aviso indica perigo. Encontra-se numa situa????o que lhe poder?? causar danos f??sicos. Antes de come??ar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos el??ctricos, e com quaisquer pr??ticas comuns que possam prevenir poss??veis acidentes. Este s??mbolo serve tamb??m para indicar que poder?? ler este tipo de aviso em v??rias l??nguas na sec????o: ???Appendix C, ???Translated Safety Warnings.???

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Related Publications

??Atenci??n! Este s??mbolo de aviso significa peligro. Existe riesgo para su integridad f??sica. Antes de manipular cualquier equipo, considerar los riesgos que entra??a la corriente el??ctrica y familiarizarse con los procedimientos est??ndar de prevenci??n de accidentes. Este s??mbolo de aviso tambi??n significa que la misma advertencia aparece en varios idiomas bajo el t??tulo ???Appendix C, ???Translated Safety Warnings.???

Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf??r arbete p?? n??gon utrustning m??ste du vara medveten om farorna med elkretsar och k??nna till vanligt f??rfarande f??r att f??rebygga skador. Denna varningssymbol inneb??r ocks?? att du kan se varningsmeddelandet p?? flera spr??k i ???Appendix C, ???Translated Safety Warnings.???

Related Publications

You can order printed copies of documents with a DOC-xxxxxx= number. For more information, see the ???Ordering Documentation??? section on page xix.

These publications provide more information about the switches that support the GigaStack GBIC:

???Catalyst 2900 Series XL Hardware Installation Guide (order number DOC-786461=)

???Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide (order number DOC-786511=) (previously titled Cisco IOS Desktop Switching Software Configuration Guide)

???Catalyst 2900 Series XL and Catalyst 3500 Series XL Command Reference (order number DOC-7812155=) (previously titled Cisco IOS Desktop Switching Command Reference)

???Catalyst 2950 Desktop Switch Hardware Installation Guide (order number DOC-7811157=)

???Catalyst 2950 Desktop Switch Software Configuration Guide (order number DOC-78111380=)

Preface

Obtaining Documentation

???Catalyst 2950 Desktop Switch Command Reference (order number DOC-78111381=)

???Catalyst 3500 Series XL Hardware Installation Guide (order number DOC-786456=)

???Catalyst 3550 Multilayer Switch Hardware Installation Guide (order number DOC-7811358=)

???Catalyst 3550 Multilayer Switch Software Configuration Guide (order number DOC-7811194=)

???Catalyst 3550 Multilayer Switch Command Reference (order number DOC-7811195=)

???Catalyst 3550 Multilayer Switch System Message Guide (order number DOC-7811196=)

???Release Notes for the Catalyst 2900 Series XL and Catalyst 3500 Series XL Switches Cisco IOS Release 12.0(5.1)WC(1) or later

???Release Notes for the Catalyst 2950 Cisco IOS Release 12.1(6)EA2 or later

???Release Notes for the Catalyst 3550 Multilayer Switches Cisco IOS Release 12.1(4)EA1 or later

Refer to the online Catalyst GigaStack Gigabit Interface Converter Switch

Compatibility Matrix listed with the GigaStack GBIC documentation on

www.cisco.com for the list of switching products supporting the GBIC.

Obtaining Documentation

These sections provide sources for obtaining documentation from Cisco Systems.

World Wide Web

You can access the most current Cisco documentation on the World Wide Web at the following sites:

???http://www.cisco.com

???http://www-china.cisco.com

???http://www-europe.cisco.com

Preface

Obtaining Documentation

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.

Ordering Documentation

Cisco documentation is available in the following ways:

???Registered Cisco Direct Customers can order Cisco Product documentation from the Networking Products MarketPlace:

http://www.cisco.com/cgi-bin/order/order_root.pl

???Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store:

http://www.cisco.com/go/subscription

???Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, in North America, by calling

800 553-NETS(6387).

Documentation Feedback

If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.

You can e-mail your comments to bug-doc@cisco.com.

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Obtaining Technical Assistance

To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:

Cisco Systems, Inc.

Document Resource Connection

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.

Cisco.com

Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.

Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.

Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco.

To access Cisco.com, go to the following website:

http://www.cisco.com

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Obtaining Technical Assistance

Technical Assistance Center

The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.

Contacting TAC through the Website

If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website:

http://www.cisco.com/tac

P3 and P4 level problems are defined as follows:

???P3???Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue.

???P4???You need information or assistance on Cisco product capabilities, product installation, or basic product configuration.

In each of the above cases, use the Cisco TAC website to quickly find answers to your questions.

To register for Cisco.com, go to the following website:

http://www.cisco.com/register/

If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website:

http://www.cisco.com/tac/caseopen

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Preface

Obtaining Technical Assistance

Contacting TAC by Telephone

If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

P1 and P2 level problems are defined as follows:

???P1???Your production network is down, causing a critical impact to business operations if service is not restored quickly. No workaround is available.

???P2???Your production network is severely degraded, affecting significant aspects of your business operations. No workaround is available.

C H A P T E R 1

Overview

The GigaStack GBIC (model WS-X3500-XL) adds port density and high-performance connectivity to supporting switches. When installed in a supporting switch, the GigaStack GBIC supports Gigabit connections in a cascaded stack or point-to-point configuration. The GigaStack GBIC autonegotiates the duplex setting of each port to maximize the bandwidth for your configuration.

Features

This section describes the GigaStack GBIC features:

???Half-duplex stacking using only one GBIC slot for each switch

Stack up to nine switches to form an independent backbone that can be managed with a single IP address. This stack gives the appearance of a single large switch for network management purposes. For this kind of connectivity, see the ???Example 1: Cascaded Stack Connection??? section on page 1-9.

???Full-duplex connectivity between two switches

You can also form a point-to-point link between two switches. The GigaStack GBIC supports one full-duplex link (in a point-to-point configuration) or up to eight half-duplex links (in a stack configuration) to other Gigabit Ethernet devices. For this kind of connectivity, see the ???Example 2: Point-to-Point Connection??? section on page 1-10.

Chapter 1 Overview

GigaStack GBIC LEDs

???Support for redundant loop configurations in a GigaStack GBIC stack

For more information, see the ???Minimum IOS Release for Redundant Loop Configurations??? section on page 1-7 and the ???Cascaded Stack Connections with a Redundant Link??? section on page 2-12

???Support for IOS Release 12.0(5)XU or later for Catalyst 2900 XL and

3500 XL switches, support for Release 12.1(6)EA2 or later for Catalyst 2950 switches, and support for Release 12.1(4)EA1 or later for Catalyst 3550 multilayer switches

???Management through the Cisco IOS command-line interface (CLI) or the web-based Cluster Management Suite (CMS)

???Field-replaceable

GigaStack GBIC LEDs

Figure 1-1 shows the LED locations on the GigaStack GBIC, and Table 1-1 describes the LED colors and their meanings.

Figure 1-1 GigaStack GBIC LEDs and Ports

Two GigaStack GBIC ports

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Chapter 1 Overview

GBIC Module Slot LEDs

Table 1-1 GigaStack GBIC LEDs

GBIC Module Slot LEDs

Figure 1-2 shows the GBIC module slot LED on the front of a supporting switch, and Figure 1-3 shows the GBIC LED location when the GigaStack GBIC is installed in the 1000BASE-X module.

Figure 1-2 GBIC Module Slot LED Location on a Switch

GBIC module slot LED

Metal flap door

1

2 3

22371

GBIC module slot

Chapter 1 Overview

Cabling Guidelines

Figure 1-3 GBIC LED Location on a 1000BASE-X Module

GBIC LED

Tighten

Screws

To Activate

WS-X2931-XL

1

22122

1000BaseX

2

GigaStack GBIC

Table 1-2 describes the switch and 1000BASE-X module GBIC slot LED colors and port status.

Table 1-2 Switch and 1000BASE-X Module GBIC Slot LEDs

Cabling Guidelines

The GigaStack GBIC uses the following Cisco proprietary cables. See Figure 1-4 and Table 1-3 for more information.

Chapter 1 Overview

Cabling Guidelines

The maximum distance for a GBIC-to-GBIC connection is 1 meter. The GigaStack GBIC requires Cisco proprietary signaling and cabling. For more information about cabling, see Appendix B, ???Connectors and Cables.???

Figure 1-4 GigaStack GBIC Cables

50-cm GigaStack cable

1394

1-m GigaStack cable

4931

22086

Table 1-3 GigaStack GBIC Cable Part Numbers

The 50-cm cable comes with the GigaStack GBIC. You can order additional cables.

Caution Do not use standard IEEE 1394 cables with the GigaStack GBIC. You must use one of the Cisco proprietary cables (CAB-GS-50CM or CAB-GS-1M). If you use any other cable, you will not have connectivity.

Caution Do not use the GigaStack GBIC with standard IEEE 1394 equipment. You might damage the equipment or lose data.

Chapter 1 Overview

Switches Supporting the GBIC

Switches Supporting the GBIC

Refer to the online GigaStack Gigabit Interface Converter Switch Compatibility Matrix listed with the GBIC documentation on www.cisco.com for the most current list of products supporting the GBIC.

Caution Installing the GBIC in or connecting it to an unauthorized device might cause damage to the GBIC, the other device, or both.

Table 1-4 lists the switches and the module supporting the GigaStack GBIC.

Table 1-4 Switches and Module Supporting the GigaStack GBIC

Chapter 1 Overview

1.The 1000BASE-X module provides one switched 1000-Mbps port in half-duplex, full-duplex, or autonegotiation mode for a GigaStack GBIC. The port supports the IEEE 802.3Z 1000BASE-X standard.

Minimum IOS Release for Redundant Loop Configurations

To ensure support for redundant loop configurations when using the GigaStack GBIC in a cascaded stack configuration, make sure that every switch in the stack is running at least the minimum IOS Release listed in Table 1-5.

Chapter 1 Overview

Minimum IOS Release for Redundant Loop Configurations

Table 1-5 Minimum IOS Release for Redundant Loop Configurations

Note All switches in a series must run the same software version. For example, if the stack includes only Catalyst 2900 series XL and 3500 series XL switches, they must run Release 12.0(5)XU or later. If the stack includes a mixture of Catalyst 2900 series XL, 3500 series XL, 2950, and 3550 switches, all the 2900 XL and 3500 XL switches must run Release 12.0(5)XW or later, all the Catalyst 2950 switches must run Release 12.1(6)EA2 or later, and all the Catalyst 3550 switches must run Release 12.1(4)EA1 or later.

For more information, see the ???Cascaded Stack Connections with a Redundant Link??? section on page 2-12. For switch software upgrade information, refer to the release notes for your switch.

Chapter 1 Overview

Deployment Examples

Deployment Examples

This section contains examples that use the GigaStack GBIC as a Gigabit uplink to aggregate traffic in a switched and shared network.

Example 1: Cascaded Stack Connection

Figure 1-5 shows the GigaStack GBIC cascaded in a half-duplex stack configuration.

Figure 1-5 Cascaded Stack Connection

Catalyst 3550 switch

Gigabit EtherChannel or 1000BASE-X link

Catalyst 2900 XL,

Catalyst 3500 XL,

or Catalyst 3550

switches

Half-duplex

GigaStack GBIC links

10/100 switched links

10/100 attached workstations

48798

Chapter 1 Overview

Deployment Examples

Example 2: Point-to-Point Connection

Figure 1-6 shows the 3500 XL switch aggregating traffic by using a GigaStack GBIC as a full-duplex, point-to-point uplink connection.

Figure 1-6 Point-to-Point Connection

Catalyst 3508G XL switch

Full-duplex GigaStack GBIC or 1000BASE-X links

48799

Catalyst 2900 XL, Catalyst 3500 XL, or Catalyst 3550 switches

C H A P T E R 2

Installation

This chapter describes how to unpack, install, cable, and run the power-on self-test (POST) on the GigaStack GBIC. After power on, you can manage GBIC ports as you would manage fixed ports on the switch, through the web-based Cluster Management Suite (CMS), or through the console port or a Telnet connection to access the IOS command-line interface.

Inspecting the Packing List

Before you install a GigaStack GBIC, ensure that these items are included in the package:

???GigaStack GBIC

???50-cm cable

???GBIC clip

If anything is missing, contact your Cisco Systems customer service representative.

Note You can order a 1-m cable separately.

Chapter 2 Installation

EMC Regulatory Statements

EMC Regulatory Statements

This section lists international regulatory information for the GigaStack GBIC.

U.S.A.

U.S. regulatory information for this product is in the front matter of this manual.

Taiwan

This is a Class A Information product. When used in a residential environment, it may cause radio frequency interference. Under such circumstances, the user may be requested to take appropriate countermeasures.

Japan

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

46464

Chapter 2 Installation

EMC Regulatory Statements

Korea

Warning This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.

Hungary

This equipment is a Class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.

Figyelmeztet??s a felhaszn??l?? i k??zik?? nyv sz??m??ra:

Ez a berendez??s ???A??? oszt??ly?? term??k, felhaszn??l??s??ra ??s ?? zembe helyez??s??re a magyar EMC ???A??? oszt??ly?? k?? vetelm??nyeknek (MSZ EN 55022) megfeleloen ker?? lhet sor, illetve ezen ???A??? oszt??ly?? berendez??sek csak megfelelo kereskedelmi forr??sb?? l sz??rmazhatnak, amelyek biztos??tj??k a megfelelo speci??lis ?? zembe helyez??si k?? r?? lm??nyeket ??s biztons??gos ?? zemel??si t??vols??gok alkalmaz??s??t.

Chapter 2 Installation

Avoiding Electrostatic Discharge

Avoiding Electrostatic Discharge

Before you install the GigaStack GBIC, ground yourself by touching the metal part of the chassis to avoid electrostatic discharge (ESD). You should also keep the GigaStack GBIC in its antistatic shielded bag until you are ready for installation.

Installing a GigaStack GBIC

Gigabit Ethernet switches are shipped without the GigaStack GBIC. However, you can install the GBIC into GigaStack GBIC slots, as shown in Figure 2-1.

Install a GigaStack GBIC as follows:

Step 1 Remove the GigaStack GBIC from its protective packaging.

Step 2 If you want to use the GigaStack cable connector (hereafter referred to as the clip), see the ???Attaching the GBIC Clip??? section on page 2-6.

Step 3 Grip the sides of the GBIC with your thumb and forefinger, and insert it into the GBIC slot on a switch front panel, as shown in Figure 2-1, or the

Catalyst 2900 XL 1000BASE-X module slot, as shown in Figure 2-2.

The GigaStack GBIC is keyed to prevent incorrect insertion.

Step 4 Slide the GigaStack GBIC through the flap covering the opening into the slot until you hear a click. The click means the GigaStack GBIC is locked into the slot.

Chapter 2 Installation

Installing a GigaStack GBIC

Figure 2-1 Inserting the GigaStack GBIC into a Switch Module Slot

Metal flap door

GigaStack GBIC

1

2 3

22081

GBIC module slot

Figure 2-2 Inserting the GigaStack GBIC into a 1000BASE-X Module

Metal flap door

GBIC LED

22085

aseX

Slot for

GigaStack GBIC

GigaStack GBIC

Chapter 2 Installation

Attaching the GBIC Clip

Attaching the GBIC Clip

Each GigaStack GBIC ships with a removable clip that can be attached to provide extra security against accidental cable removal. If you use the clip, you must attach it before inserting the GBIC into the slot.

Attach the clip as follows:

Step 1 Attach the clip to the GBIC by carefully inserting the clip tabs into the slots on either side of the GBIC, in the orientation shown in Figure 2-3. Slide the clip toward the port side of the GBIC.

Figure 2-3 Attaching the GBIC Clip

Step 2 Insert the cable connector into the GBIC port according to your configuration.

Step 3 Swing the GBIC clip up toward the GBIC so that the alignment bump in the clip seats in the indentation on the GBIC bottom.

Chapter 2 Installation

Recommended Configuration

Step 4 Secure the cable in a clip notch as shown in Figure 2-4.

Figure 2-4 Securing the Cables in the GBIC Clip

6

32257

7

8

2

Clip installed on GBIC

Step 5 Insert the GBIC into the slot. Follow the steps in the ???Installing a GigaStack GBIC??? section on page 2-4.

Recommended Configuration

All ports are set to autonegotiate the duplex mode for your GigaStack GBIC. You must keep this default setting; autonegotiation must not be disabled.

For information about the supporting switches and software, see the ???Switches Supporting the GBIC??? section on page 1-6 and the ???Minimum IOS Release for Redundant Loop Configurations??? section on page 1-7.

Connecting to GigaStack GBIC Ports

Insert the GigaStack cable connector into the GigaStack GBIC port, as shown in Figure 2-5.

Note The GBIC module slot LED is amber while the Spanning Tree Protocol discovers the topology and searches for loops. This takes about 30 seconds. The port status LED then turns green.

Chapter 2 Installation

Creating Connections

Figure 2-5 Inserting the Cable in a GigaStack GBIC

22082

1394

GBIC module slots

GigaStack cable

1394

6

7

8

Note Always use a GigaStack cable to connect a GigaStack GBIC to any device. For more information, see the ???GigaStack GBIC Cabling??? section on page B-1.

Creating Connections

You can create these configurations:

???Point-to-point

???Cascaded stack

???Cascaded stack with a redundant link

In a point-to-point configuration or cascaded stack configuration, the GigaStack GBIC can use the ports listed in Table 2-1 to connect to other devices.

Chapter 2 Installation

Creating Connections

Table 2-1 Available GBIC Ports in a Point-to-Point Configuration

Note The GigaStack GBIC supports setting a trunk to IEEE 802.1Q or Inter-Switch Link (ISL) encapsulation. All GigaStack GBIC interfaces in the cascaded stack should be configured as trunk interfaces (switchport mode trunk interface configuration command) and to use the same encapsulation method (switchport trunk encapsulation {isl | dot1q} interface configuration command). For more information on these commands, refer to the command reference for your switch.

For more information, see the ???Point-to-Point Connections??? section on page 2-10, the ???Cascaded Stack Connections??? section on page 2-11, and the ???Cascaded Stack Connections with a Redundant Link??? section on page 2-12.

Chapter 2 Installation

Creating Connections

Point-to-Point Connections

A point-to-point connection operates in full-duplex mode. Figure 2-6 shows an example of supporting switches with point-to-point connections.

Figure 2-6 Point-to-Point Connections

MODE

Catalyst 2924M XL

22304

Catalyst 3508G XL

MODE

Catalyst 2924M XL

22305

Chapter 2 Installation

Creating Connections

Cascaded Stack Connections

You can connect from three to nine switches in a cascaded stack configuration. The cascaded stack operates in half-duplex mode. Figure 2-7 shows the connections on some supporting switches.

Figure 2-7 Cascaded Stack Connections

Catalyst 3508G XL

Port 1

Port 2

Catalyst 3500XL

Catalyst 2924M XL

Catalyst 2900

MODE

Catalyst 3512 XL

Catalyst 3500XL

Catalyst 3524 XL

Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide

Chapter 2 Installation

Creating Connections

Cascaded Stack Connections with a Redundant Link

You can form a redundant link by connecting the open ports on the top and bottom GigaStack GBICs within the same stack, as shown in Figure 2-8.

Figure 2-8 Cascaded Stack Connections with a Redundant Link

Catalyst 3508G XL

Port 1

Port 2

Catalyst 3500XL

Catalyst 3512 XL

Catalyst 3524 XL

Catalyst 3500XL

Redundant

link

Catalyst 3500XL

The GigaStack GBIC software detects the loop configuration by the way the cables are connected and the number of switches used in the stack. The software uses one of the GigaStack GBIC links as the redundant link, which is disabled for data transmission while all the other links in the stack are up. When any other link in the stack is down, the redundant link is automatically enabled for data transmission. To ensure continued connectivity, the software periodically checks for changes in the stack and invokes the loop detection algorithm if a new link is added to the cascaded stack or if a link is removed from the cascaded stack.

GigaStack GBICs installed in a stack support a loop configuration only if every Catalyst 2900 XL and 3500 XL switch in the stack is running IOS software Release 12.0(5)XU or later, Release 12.1(6)EA2 or later for Catalyst 2950 switches, and Release 12.1(4)EA1 or later for Catalyst 3550 switches.

For Catalyst 2900 XL and 3500 XL switches running IOS software earlier than Release 12.0(5)XU, an illegal loop is created under these conditions:

???A GigaStack GBIC is connected to two other GBIC ports in the same stack.

???A single GigaStack GBIC cable is inserted in port 1 and port 2 of the same GBIC.

Chapter 2 Installation

Removing a GigaStack GBIC

Caution A loop causes excessive collision errors on the port and can cause the link to become unstable. This instability decreases performance on the links, and communication between the switches in the stack is adversely affected.

If a Catalyst switch is connected through its GigaStack GBIC to another switch???s GigaStack GBIC that does not support loop detection, the GBIC LEDs turn these colors:

???The GigaStack GBIC LED on the switch without loop detection turns green almost immediately.

???The GigaStack GBIC LED on the switch with loop detection flashes green for 15 seconds and then turns green.

As a result, all GBIC links are enabled if no loop is created. If a loop is present, the software does not detect it, excessive collisions occur on these ports, no traffic passes through the stack, and the GigaStack GBIC LEDs remain green.

To avoid problems with loop configurations, make sure that all switches in your stack are running the appropriate IOS release as shown in Table 1-5 on page 1-8. For more information, see the ???Minimum IOS Release for Redundant Loop Configurations??? section on page 1-7. For switch software upgrade information, refer to the release notes for your switch.

Removing a GigaStack GBIC

Remove a GigaStack GBIC as follows:

Step 1 Release the GigaStack GBIC from the slot by simultaneously squeezing the two plastic tabs (one on each side of the GigaStack GBIC).

Step 2 To remove, slide the GigaStack GBIC out of the slot. A flap drops down to protect the internal connector.

Chapter 2 Installation

Power-On Self-Test

Step 3 If you are using the GBIC clip to secure the GBIC cables, remove the clip from the GigaStack GBIC by pulling the tabs from the slots on the GBIC. Remove the cables from the notches in the clip.

Step 4 Disconnect the cable from the GigaStack GBIC port.

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Power-On Self-Test

All supporting switches perform a power-on self-test (POST) on the GigaStack GBIC. When you insert the GigaStack GBIC into the switch or module slot, the port LED on the switch or module turns amber while STP checks for possible loops and then turns green. When you insert a GigaStack GBIC cable into the GBIC port, the GigaStack GBIC port turns green if there is network connectivity; no additional configuration is needed. For more information about the LED meanings, see the ???GigaStack GBIC LEDs??? section on page 1-2 and the ???GBIC Module Slot LEDs??? section on page 1-3.

C H A P T E R 3

Troubleshooting

Table 3-1 describes how to identify problems with the switch and GigaStack

GBIC and how to resolve them.

Table 3-1 Common Problems and Their Solutions

Chapter 3 Troubleshooting

Table 3-1 Common Problems and Their Solutions (continued)

A P P E N D I X A

Technical Specifications

Table A-1 lists the technical specifications and regulatory agency approvals for the GigaStack GBIC.

Table A-1 Technical Specifications

Environmental Ranges

Appendix A Technical Specifications

Table A-1 Technical Specifications (continued)

Agency Approvals

A P P E N D I X B

Connectors and Cables

This appendix describes the Cisco proprietary cables and connectors for the

GigaStack GBIC.

GigaStack GBIC Cabling

The GigaStack GBIC uses proprietary connectors as shown in Figure B-1.

Figure B-1 GigaStack GBIC Connector

22084

The GigaStack GBIC cables are proprietary, high-data-rate cables with enhanced signal integrity and EMI performance.

Caution Do not use standard IEEE 1394 cables with the GigaStack GBIC. You must use one of the Cisco proprietary cables (CAB-GS-50CM or CAB-GS-1M). If you use any other cable, you will not have connectivity.

Caution Do not use the GigaStack GBIC with standard IEEE 1394 equipment. You might damage the equipment or lose data.

Appendix B Connectors and Cables

GigaStack GBIC Cabling

A P P E N D I X C

Translated Safety Warnings

This appendix repeats the warnings in this guide in multiple languages.

Product Disposal

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Waarschuwing Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.

Varoitus T??m?? tuote on h??vitett??v?? kansallisten lakien ja m????r??ysten mukaisesti.

Attention La mise au rebut ou le recyclage de ce produit sont g??n??ralement soumis ?? des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr??s de l'organisme comp??tent.

Warnung Die Entsorgung dieses Produkts sollte gem???? allen

Bestimmungen und Gesetzen des Landes erfolgen.

Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.

Appendix C Translated Safety Warnings

Product Disposal

Advarsel Endelig kassering av dette produktet skal v??re i henhold til alle relevante nasjonale lover og bestemmelser.

Aviso Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.

??Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.

Varning! Vid deponering hanteras produkten enligt g??llande lagar och best??mmelser.

Numerics

1000BASE-X module description 1-7

IEEE standards 1-7

A

agency approvals A-2 alignment errors 1-4 autonegotiation 2-7

C

cable

1-m cable availability 2-1 description and cautions B-1 guidelines 1-5, B-1

lengths 1-5

part numbers 1-5, B-1 proprietary requirements 1-5

standard IEEE 1394 cable caution 1-5, B-1

Cisco IOS command-line interface, (CLI) 1-2

Cisco Technical Assistance Center xxi clip, attaching 2-6 to 2-7

I N D E X

Cluster Management Suite (CMS) 1-2 collision errors 2-13

CRC errors 1-4

D

definitions, notes, cautions, warnings xiv deployment examples 1-9 to 1-10

disabled port 1-4 distance limitations 1-5 documentation

feedback xix obtaining

CD-ROM xix

world wide web xviii ordering xix

related xvii

duplex mode, recommended 2-7

E

electrostatic discharge (ESD) 2-4

EMC regulatory statements 2-2

EMI agency approvals A-2

Index

error frames

detecting 3-1

LED indication 1-4

Spanning Tree Protocol 3-1

F

features 1-1 to 1-2

feedback to Cisco Systems, web xix

G

GigaStack cable connector, see clip GigaStack GBIC

cabling guidelines 1-5 connecting ports 2-7 definition xiii deployment examples

cascaded connection 1-9 point-to-point connection 1-10

installing 2-4

keyed insertion protection 2-4

LED descriptions 1-3 minimum IOS Release 1-7 part number 1-1

recommended duplex mode 2-7 redundant loop support 1-7, 2-12 removing 2-13

specifications A-1 to A-2

supported switches 1-6

GigaStack Gigabit Interface Converter,

see GigaStack GBIC

I

IEEE 1394 (standard) cable caution 1-5

IEEE standards 802.1Q 2-9

802.3Z 1-7

installation procedure 2-4 to 2-7

Inter-Switch Link (ISL) mode, support 2-9

IOS software

illegal loops with 2-12 support 1-2, 1-7

IP address, managing a stack 1-1

L

LEDs

color meanings 1-2 to 1-4

during Spanning Tree Protocol 2-7

POST failure 1-3 troubleshooting 3-1 to 3-2

link, point-to-point 1-1 link flap 3-2

loop detection 2-12

N

network examples 1-9 note definition xiv

P

packing list 2-1

POST

conditional limitations 2-14

LED indicator 1-3 power-on self-test, see POST product disposal C-1

R

redundant links

configuration example 2-12 supported IOS Release 1-7, 2-12

regulatory statements 2-2 related publications xvii removing a GigaStack GBIC 2-13

S

safety

agency approvals A-2 warnings, translated C-1

Index

Spanning Tree Protocol LED state during 2-7 port blocking 1-4

specifications A-1 stacking

full-duplex cascaded example 1-10 half-duplex cascaded example 1-9 redundant link example 2-12

switches, supported

IOS release requirements 1-7 support for GigaStack GBIC 1-6

T

TAC

described xxi

toll-free telephone numbers xxii technical assistance

Cisco.com xx

TAC website xxi technical specifications A-1 topology

cascaded 1-9 point-to-point 1-10 redundant link 2-12

troubleshooting 3-1 to 3-2 trunking 2-9

Index

U

URLs, Cisco xviii

W

warnings, Product Disposal C-1

World Wide Web, documentation from xviii