2005 Chevrolet Colorado Owner Manual M
2005 Chevrolet Colorado Owner Manual M
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, and the name COLORADO are registered trademarks of General Motors Corporation.
This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice. For vehicles ???rst sold in Canada, substitute the name ???General Motors of Canada Limited??? for Chevrolet Motor Division whenever it appears in this manual.
Keep this manual in the vehicle, so it will be there if it is needed while you are on the road. If the vehicle
is sold, leave this manual in the vehicle.
Litho in U.S.A.
Part No. 05COLORADO A First Edition
Canadian Owners
A French language copy of this manual can be obtained from your dealer or from:
Helm, Incorporated
P.O. Box 07130
Detroit, MI 48207
How to Use This Manual
Many people read the owner manual from beginning to end when they ???rst receive their new vehicle. If this
is done, it can help you learn about the features
and controls for the vehicle. Pictures and words work together in the owner manual to explain things.
Index
A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found.
?? 2004 General Motors Corporation. All Rights Reserved.
ii
Safety Warnings and Symbols
There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning.
{CAUTION:
These mean there is something that could hurt you or other people.
In the caution area, we tell you what the hazard is. Then we tell you what to do to help avoid or reduce the hazard. Please read these cautions. If you do not,
you or others could be hurt.
You will also ???nd a circle with a slash through it in this book. This safety symbol means ???Do Not,??? ???Do Not do this??? or ???Do Not let this happen.???
iii
Vehicle Damage Warnings
Also, in this manual you will ???nd these notices:
Notice: These mean there is something that could damage your vehicle.
A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle???s warranty, and it could be costly. But the notice will tell what to do to help avoid the damage.
When you read other manuals, you might see CAUTION and NOTICE warnings in different colors or in different words.
There are also warning labels on the vehicle. They use the same words, CAUTION or NOTICE.
Vehicle Symbols
The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a speci???c component, control, message, gage, or indicator.
If you need help ???guring out a speci???c name of a component, gage, or indicator, reference the following topics:
???Seats and Restraint Systems in Section 1
???Features and Controls in Section 2
???Instrument Panel Overview in Section 3
???Climate Controls in Section 3
???Warning Lights, Gages, and Indicators in Section 3
???Audio System(s) in Section 3
???Engine Compartment Overview in Section 5
iv
These are some examples of symbols that may be found on the vehicle:
v
??? NOTES
vi
Section 1 Seats and Restraint Systems
Front Seats
Manual Seats
This section tells you about the seats ??? how to adjust them, and fold them up and down.
{CAUTION:
You can lose control of the vehicle if you try to adjust a manual driver???s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver???s seat only when the vehicle is not moving.
Move the lever located under the front of a manual seat up to unlock it. Slide the seat to where you want it
and release the lever. Try to move the seat with your body to make sure the seat is locked into place.
Power Seats
If your vehicle has this feature, there will be a control on the outboard side of the front seat(s).
Horizontal Control: Raise or lower the front of the seat by raising or lowering the forward edge of the control.
Raise or lower the rear of the seat by raising or lowering the rear edge of the control.
Move the seat forward or rearward by moving the whole control toward the front or the rear of the vehicle.
Moving the whole control up or down raises or lowers the whole seat.
Vertical Control: This control reclines the seatbacks. See Reclining Seatbacks on page
Manual Lumbar
If your vehicle has this feature, there will be a knob located on the outboard side of the driver???s seat.
Turn the knob counterclockwise to increase lumbar support and clockwise to decrease lumbar support.
Heated Seats
If your vehicle has this feature, the controls are located on the outboard side of the front seats.
This feature will quickly heat the lower cushion and lower back of the driver???s and front passenger???s seats for added comfort.
Press the lower part of the switch to turn the heater on at low heat. Press the upper part of the switch to
turn the heater on at high heat. Put the switch in the center position to turn the heater off.
The ignition must be on for the heated seat feature to work. The passenger???s safety belt must be engaged for the heated seat feature to work on the passenger???s seat.
Reclining Seatbacks
Your vehicle may have reclining seatbacks.
To manually recline your seatback, lift the lever on the outboard side of the seat.
Release the lever to lock the seatback where you want it. Pull up on the lever and without pushing on the seatback, the seat will go to an upright position.
If you have power seats, you can use the vertical power seat control to recline the seatback. Move the reclining front seatback forward or rearward by moving the control toward the front or rear of the vehicle.
But don???t have a seatback reclined if your vehicle is moving.
{CAUTION:
Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this.
The shoulder belt can not do its job because it will not be against your body. Instead, it will be in front of you. In a crash you could go into it, receiving neck or other injuries.
The lap belt can not do its job either. In a crash the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries.
For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear your safety belt properly.
Head Restraints
If your vehicle is equipped with adjustable head restraints, adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash.
Push up on the head restraint to raise it. To lower the head restraint, press the button located on top of the seatback and push down on the head restraint.
Seatback Latches
Your vehicle may be equipped with front seatbacks that fold forward to let people get into the rear seat or to access the storage area behind the seat.
To fold the front seatback forward, push the lever on the side of the seat rearward and pull the seatback forward.
{CAUTION:
If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
To return the seatback to the upright position, push the seatback all the way back until the latch catches. If the seatback was reclined before being folded forward, it will return to the reclined position.
Rear Seats
Rear Seat Operation (Crew Cab)
If your vehicle is a crew cab, the rear seatback can be folded forward. Before you can fold the rear seatback, you need to unlatch the center safety belt buckle.
Use the following steps to lower one or both of the rear seatbacks:
1.Insert a tool with a small tip into the slot to unlatch the center position safety belt buckle. Then move the belt to the side so it is not in the way.
2.Grasp the loop located on the side of the seatback you want to fold and pull until
you hear a click.
{CAUTION:
A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
3.Fold the seatback down.
4.Repeat Steps 2 and 3 to fold down the other seatback.
{CAUTION:
If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
To return the seatback to the upright position, do the following:
1.Lift the seatback up and push it back into place.
2.Reconnect the center safety belt latch plate to the buckle.
3.Make sure the seatback is locked into place by pushing and pulling on it.
4.Repeat Steps 1 and 3 for the other seatback.
When the seatback is not in use, it should be kept in the upright, locked position.
Rear Seat Operation (Extended Cab)
If your vehicle has an extended cab, there may be a forward folding seat in the rear area.
To fold the rear seat down, pull down on the bottom of the seat until the seat is in place.
The rear seat storage compartments must be in the rearward position before folding the seat down.
To store the seat, do the following:
1.To ensure that the safety belt buckle does not move when not in use, secure it to the inboard side of the seat by the hook and loop fastener (A) .
2.Push the entire seat up until it is ???ush with the trim panel.
Safety Belts
Safety Belts: They Are for Everyone
This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts.
{CAUTION:
Do not let anyone ride where he or she can not wear a safety belt properly. If you are in a crash and you are not wearing a safety belt, your injuries can be much worse. You can hit things inside the vehicle or be ejected from it. You can be seriously injured or killed. In the same crash, you might not be, if you are buckled up. Always fasten your safety belt, and check that your passengers??? belts are fastened properly too.
{CAUTION:
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
Your vehicle has a light that comes on as a reminder to buckle up. See
Light on page
In most states and in all Canadian provinces, the law says to wear safety belts. Here is why: They work.
You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one.
A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without belts they could have been badly hurt or killed.
After more than 30 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter...a lot!
Why Safety Belts Work
When you ride in or on anything, you go as fast as it goes.
Take the simplest vehicle. Suppose it is just a seat on wheels.
or the safety belts!
With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Questions and Answers About
Safety Belts
Q:
A: You could be ??? whether you are wearing a safety belt or not. But you can unbuckle a safety belt, even if you are upside down. And your chance of being conscious during and after an accident,
so you can unbuckle and get out, is much greater if you are belted.
Q:
A: Airbags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts ??? not instead of them. Every airbag
system ever offered for sale has required the use of safety belts. Even if you are in a vehicle that has airbags, you still have to buckle up to get the most protection. That is true not only in frontal collisions, but especially in side and other collisions.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts?
A: You may be an excellent driver, but if you are in an accident ??? even one that is not your fault ??? you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h).
Safety belts are for everyone.
How to Wear Safety Belts Properly
This part is only for people of adult size.
Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page
First, you will want to know which restraint systems your vehicle has.
We will start with the driver position.
Driver Position
The driver has a
1.Close and lock the door.
2.Adjust the seat so you can sit up straight. To see how, see ???Seats??? in the Index.
3.Pick up the latch plate and pull the belt across you. Do not let it get twisted.
The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
4.Push the latch plate into the buckle until it clicks.
Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page
Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
5.To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
The safety belt locks if there is a sudden stop or crash, or if you pull the belt very quickly out of the retractor.
Q: What is wrong with this?
A: The shoulder belt is too loose. It will not give nearly as much protection this way.
{CAUTION:
You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ???t against your body.
Q: What is wrong with this?
A: The belt is buckled in the wrong place.
{CAUTION:
You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you.
Q: What is wrong with this?
A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
{CAUTION:
You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen.
Q: What is wrong with this?
A: The belt is twisted across the body.
{CAUTION:
You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ???x it.
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage
both the belt and your vehicle.
Shoulder Belt Height Adjustment
Before you begin to drive, move the shoulder belt height adjuster to the height that is right for you.
Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder.
To move it up or down, squeeze the release buttons (A) together and move the height adjuster to the desired position. After you move the adjuster to where you want it, try to move it down without squeezing the release buttons to make sure it has locked into position.
Safety Belt Use During Pregnancy
Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts.
A pregnant woman should wear a
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Right Front Passenger Position
To learn how to wear the right front passenger???s safety belt properly, see Driver Position on page
The right front passenger???s safety belt works the same way as the driver???s safety belt ??? except for one thing. If you ever pull the shoulder portion of the belt out all the way, you will engage the child restraint locking feature. If this happens, just let the belt go back all the way and start again.
Center Front Passenger Position
Lap Belt
If your vehicle has a 60/40 split front seat, someone can sit in the center position.
When you sit in the center front seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along
the belt.
To make the belt shorter, pull its free end as shown until the belt is snug.
Buckle, position and release it the same way as the lap part of a
Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt
quickly if you ever had to.
Rear Seat Passengers
It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts.
Rear passengers who are not safety belted can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts.
All rear seating positions have
1. Pick up the latch plate and pull the belt across you. Do not let it get twisted.
The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
2.Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.
When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again.
If the belt is not long enough, see Safety Belt Extender on page
Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
The safety belt locks if there is a sudden stop or a crash.
The safety belt also locks if you pull the belt very quickly out of the retractor.
{CAUTION:
You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ???t against your body.
To unlatch the belt, just push the button on the buckle.
Rear Safety Belt Comfort Guides for
Children and Small Adults
Your vehicle may have rear safety belt comfort guides for the rear outside positions.
Rear safety belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When attached to a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Here is how to attach the comfort guide to the shoulder belt.
1. Slide the guide off of its storage clip located between the interior body and the seatback.
2.Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt and insert the two edges of the
belt into the slots of the guide.
3.Be sure that the belt is not twisted and it lies ???at. The elastic cord must be under the belt and the guide on top.
4.Buckle, position and release the safety belt as described in Rear Seat Passengers on page
To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides. Slide the guide back on its storage clip located between the interior body and the seatback.
Safety Belt Pretensioners
Your vehicle has safety belt pretensioners. Although you cannot see them, they are located on the retractor part of the safety belts for the driver and right front passenger. They help the safety belts reduce a person???s forward movement in a moderate to severe frontal or near frontal crash.
Pretensioners work only once. If they activate in a crash, you will need to get new ones, and probably other new parts for your safety belt system. See Replacing Restraint System Parts After a Crash on page
Safety Belt Extender
If the vehicle???s safety belt will fasten around you, you should use it.
But if a safety belt is not long enough, your dealer will order you an extender. It is free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. To help avoid personal injury, do not let someone else use it, and use it only for the seat it is made to ???t. The extender has been designed for adults. Never use it for securing child seats. To wear it, just attach it to the regular safety belt. For more information, see the instruction sheet that comes with the extender.
Child Restraints
Older Children
Older children who have outgrown booster seats should wear the vehicle???s safety belts.
If you have a choice, a child should sit in a seat that has a
Q: What is the proper way to wear safety belts?
A: If possible, an older child should wear a
Accident statistics show that children are safer if they are restrained in a rear seat.
In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle. Older children need to use safety belts properly.
{CAUTION:
Never do this.
Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time.
Q: What if a child is wearing a
A: If the child is sitting in a rear outside seat position, move the child toward the center of the vehicle. See
Rear Safety Belt Comfort Guides for Children and Small Adults on page
{CAUTION:
Never do this.
Here a child is sitting in a seat that has a
Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child???s thighs. This applies belt force to the child???s pelvic bones in a crash.
Infants and Young Children
Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle???s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint.
{CAUTION:
People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much ??? until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only
25 mph (40 km/h), a
{CAUTION:
Children who are up against, or very close to, any airbag when it in???ates can be seriously injured or killed. Airbags plus
Q: What are the different types of
A:
into consideration not only the child???s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used
in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
The restraint manufacturer???s instructions that come with the restraint state the weight and height limitations for a particular child restraint. In addition, there are many kinds of restraints available for children with special needs.
{CAUTION:
Newborn infants need complete support, including support for the head and neck. This is necessary because a newborn infant???s neck is weak and its head weighs so much compared with the rest of its body. In a crash, an infant in a
{CAUTION:
The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child???s hip bones are still so small that the vehicle???s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child???s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fatal injuries. Young children always should be secured in appropriate child restraints.
Child Restraint Systems
An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ???at surface. Make sure that the infant???s head rests toward the center of the vehicle.
A
A
A booster seat
Q: How do child restraints work?
A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A
is purchased by the vehicle???s owner.
For many years,
reduce the chance of injury, the child also has to be secured within the restraint. The vehicle???s belt system secures the
One system, the
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards.
Then follow the instructions for the restraint. You may ???nd these instructions on the restraint itself or in a booklet, or both. These restraints use the belt system or the LATCH system in your vehicle, but the child also has to be secured within the restraint to help reduce the chance of personal injury. When securing an
Where to Put the Restraint
Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors recommends that child restraints be secured in a rear seat including an infant riding in a
Never put a child in a
{CAUTION:
A child in a
CAUTION: (Continued)
CAUTION: (Continued)
Even though the airbag off switch is designed to turn off the right front passenger???s frontal airbag, no system is
If you need to secure a
Do not use child restraints in the center front seat position. The restraints will not work properly.
If you need to secure a
Wherever you install it, be sure to secure the child restraint properly.
Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle ??? even when no child is in it.
Top Strap
Some child restraints have a top strap, or ???top tether???. It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top
If the child restraint does not have a top strap, one can be obtained, in kit form, for many child restraints.
Ask the child restraint manufacturer whether or not a kit is available.
In Canada, the law requires that
Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. If you have an adjustable head restraint, route the top strap over it.
When using a top
{CAUTION:
Each top tether bracket is designed to anchor only one child restraint. Attaching more than one child restraint to a single bracket could cause the anchor to come loose or even break during a crash. A child or others could be injured if this happens. To help prevent injury to people and damage to your vehicle, attach only one child restraint per bracket.
Once you have the top strap anchored, you will be ready to secure the child restraint itself. Tighten the top strap when and as the child restraint manufacturer???s instructions say.
Top Strap Anchor Location
{CAUTION:
Children who are up against, or very close to any airbag when it in???ates can be seriously injured or killed. See Where to Put the Restraint on page
Crew Cab
Crew Cab
A.Top Strap Anchorage
B.Seatback Latch
There are top strap anchors on the back wall behind each rear seating position. You must pull the seatback forward to access the top strap anchors (A). See
Rear Seat Operation (Crew Cab) in the Index.
1.Release the rear seatback from its latches (B). See
Rear Seat Operation (Crew Cab) in the Index for instructions.
2.Attach the top strap to the anchor (A).
Make sure that you secure the top strap to the top strap anchor (A) and not to the seatback latch (B).
3.Push rearward on the seatback until it locks into its upright position.
Push and pull on the seatback to make sure it is secured properly.
Do not secure a child restraint with a top strap in the right front passenger???s position if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. There is no place
to anchor the top strap in this position.
Extended Cab with Rear Seats
Extended Cab with Rear Seats
A.Top strap routing loops
B.Top strap anchors
C.LATCH anchors (See Lower Anchorages and Top Tethers for Children (LATCH System) on page
There are two top strap anchorages on the center of the back wall located behind a removable cover for the
rear seating positions. You must route the top strap through the loop (A) at the top of the seatback to attach the top strap to the one of the top strap anchors (B)
as shown.
Do not secure a child restraint with a top strap in the right front passenger???s position if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. There is no place
to anchor the top strap in this position.
Regular and Extended Cabs without Rear Seats
There is a top strap anchor located behind a removable cover on the back wall behind the right front passenger seat. You must pull the seatback forward to access the top strap anchors. See Seatback Latches on page
Lower Anchorages and Top Tethers for Children (LATCH System)
Your vehicle is equipped with the LATCH System.
For crew cabs, there are anchors for each outboard seating position. You will ???nd the anchors where
the seatback meets the back of the seat cushion.
For extended cabs with rear seats, there are anchors for each rear seating position. You will ???nd the anchors attached to the back wall near the seat cushion.
For regular cabs and extended cabs without rear seats, there are anchors for the right front passenger position. You will ???nd the anchors where the seatback meets the back of the seat cushion.
To assist you in locating the anchors, place your hand in a
seat cushion and the seatback.
This system, designed to make installation of child restraints easier, does not use the vehicle???s safety belts. Instead, it uses vehicle anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top
tether strap.
A.Lower Anchorage
B.Lower Anchorage
C.Top Tether
A.Lower Anchorage
B.Lower Anchorage
In order to use the LATCH system in your vehicle, you need a child restraint designed for that system.
{CAUTION:
If a
Securing a Child Restraint Designed for the LATCH System (Crew Cab)
1.Find the LATCH anchorages for the seating position you want to use. See Lower Anchorages and Top Tethers for Children (LATCH System) on page
2.Put the child restraint on the seat.
3.If the child restraint is
4.Attach the LATCH attachments on the child restraint to the LATCH anchorages in the vehicle. The child restraint instructions will show you how.
5.Tighten the LATCH attachments and the top tether. The child restraint instructions will show you how.
6.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, disconnect the latch attachments, pull the seatback forward and unhook the top tether from the top tether anchorage. Be sure to return the seatback to its fully upright position. See Rear Seat Operation (Crew Cab) in the Index.
Securing a Child Restraint Designed for the LATCH System (Extended Cab with Rear Seats)
1.Find the LATCH anchorages for the seating position you want to use. See Lower Anchorages and Top Tethers for Children (LATCH System) on page
2.Put the child restraint on the seat.
3.Attach the LATCH attachments on the child restraint to the LATCH anchorages in the vehicle. The child restraint instructions will show you how.
4.If the child restraint is
5.Tighten the LATCH attachments and top tether. The child restraint instructions will show you how.
6.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, disconnect the latch attachments and unhook the top tether from the top tether anchorage.
Securing a Child Restraint Designed for the LATCH System (Regular/ Extended Cab - No Rear Seats)
Your vehicle has airbags. Regular cab models and extended cab models without rear seats have an airbag off switch on the instrument panel you can use to
turn off the right front passenger???s frontal airbag. See
Airbag Off Switch on page
United States
Canada
Unless the right front passenger???s frontal airbag has been turned off, never put a
{CAUTION:
A child in a
Even though the airbag off switch is designed to turn off the right front passenger???s frontal airbag, no system is
{CAUTION:
If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger???s frontal airbag could in???ate even though the switch is off. If this ever happens, do not let anyone whom the national government has identi???ed as a member of a passenger airbag risk group sit in the right front passenger???s position (for example, do not secure a
1.Your vehicle has a right front passenger???s frontal airbag. See Airbag Off Switch on page
or Power Seats on page
2.Find the LATCH anchorages in the passenger seat. See Lower Anchorages and Top Tethers for Children (LATCH System) on page
3.Put the child restraint on the seat.
4.Attach the LATCH attachments on the child restraint to the LATCH anchorages in the vehicle. The child restraint instructions will show you how.
5.If the child restraint is
forward to access the top tether anchorage. See
Seatback Latches on page
6.Tighten the LATCH attachments and top tether. The child restraint instructions will show you how.
7.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, loosen and disconnect the LATCH attachments and loosen the top tether. Pull the seatback forward, and unhook the top tether from the top tether anchorage. Be sure to return the seatback to its fully upright position. See Seatback Latches on page
Turn on the right front passenger???s frontal airbag when you remove the child restraint from the vehicle unless the person who will be sitting there is a member of
a passenger airbag risk group. See Airbag Off Switch on page
{CAUTION:
If the right front passenger???s frontal airbag is turned off for a person who is not in a risk group identi???ed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag would not be able to in???ate and help protect the person sitting there. Do not turn off the right front passenger???s frontal airbag unless the person sitting there is in a risk group. See Airbag Off Switch on page
Securing a Child Restraint in a Rear
Seat Position
If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page
If your child restraint does not have the LATCH system, you will be using the
1.Put the child restraint on the seat.
2.Pick up the latch plate, and run the lap and shoulder portions of the vehicle???s safety belt through or around the restraint. The child restraint instructions will show you how.
3.Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
4.Pull the rest of the shoulder belt all the way out of the retractor to set the lock (crew cab only).
5.To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder
belt back into the retractor. If you are using a
6.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle???s safety belt and let it go back all the way. The safety
belt will move freely again and be ready to work for an adult or larger child passenger.
Securing a Child Restraint in the
Center Front Seat Position
Do not use child restraints in this position. The restraints will not work properly.
Securing a Child Restraint in the Right Front Seat Position (Models without an Airbag Off Switch)
Crew Cab Models and Extended Cab Models with Rear Seats
If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page
There is no top strap anchor in the right front passenger???s position. Do not secure a child seat in this position if a national or local law requires that the
top strap be anchored, or if the instructions that come with the child restraint say that the top strap must
be anchored. See Top Strap on page
Your vehicle has a right front passenger airbag. Never put a
{CAUTION:
A child in a
A rear seat is a safer place to secure a
If your child restraint does not have the LATCH system, you will be using the
1.Because your vehicle has a right front passenger???s frontal airbag, always move the seat as far back as it will go before securing a
2.Put the child restraint on the seat.
3.Pick up the latch plate, and run the lap and shoulder portions of the vehicle???s safety belt through or around the restraint. The child restraint instructions
5.Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6.To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder
belt back into the retractor. If you are using a
7.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle???s safety belt and let it go back all the way. The safety
belt will move freely again and be ready to work for an adult or larger child passenger.
Securing a Child Restraint in the Right Front Seat Position (Models with an Airbag Off Switch)
Regular Cab Models and Extended Cab Models without Rear Seats
Your vehicle has a right front passenger???s frontal airbag. Regular cab models and extended cab models without rear seats have a switch on the instrument panel
that you can use to turn off the right front passenger???s frontal airbag. See Airbag Off Switch on page
for more on this, including important safety information.
United States
Canada
Unless the right front passenger???s frontal airbag has been turned off, never put a rear facing child restraint in the right front passenger???s seat. Here is why:
{CAUTION:
A child in a
Even though the airbag off switch is designed to turn off the right front passenger???s frontal airbag, no system is
{CAUTION:
If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger???s frontal airbag could in???ate even though the switch is off. If this ever happens, do not let anyone whom the national government has identi???ed as a member of a passenger airbag risk group sit in the right front passenger???s position (for example, do not secure a
If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page
If your child restraint does not have the LATCH system, you will be using the
1.Your vehicle has a right front passenger???s frontal airbag. See Airbag Off Switch on page
or Power Seats on page
2.Put the child restraint on the seat.
3.Pick up the latch plate, and run the lap and shoulder portions of the vehicle???s safety belt through or around the restraint. The child restraint instructions will show you how.
4.Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
5.Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6.To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder
belt back into the retractor. If you are using a
7.Push and pull the child restraint in different directions to be sure it is secure.
To remove the child restraint, just unbuckle the vehicle???s safety belt and let it go back all the way. The safety
belt will move freely again and be ready to work for an adult or larger child passenger.
If you were using a
{CAUTION:
If the right front passenger???s frontal airbag is turned off for a person who is not in a risk group identi???ed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag would not be able to in???ate and help protect the person sitting there. Do not turn off the right front passenger???s frontal airbag unless the person sitting there is in a risk group. See Airbag Off Switch on page
Airbag System
Your vehicle has airbags ??? a frontal airbag for the driver and a frontal airbag for the right front passenger. Your vehicle may also have a
Airbags are designed to help reduce the risk of injury from the force of an in???ating airbag. But these airbags must in???ate very quickly to do their job and comply with federal regulations.
Here are the most important things to know about the airbag system:
{CAUTION:
You can be severely injured or killed in a crash if you are not wearing your safety belt ??? even
if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it. Airbags are ???supplemental restraints??? to the safety belts. All airbags are designed to work with safety belts but do not replace them.
Frontal airbags for the driver and right front passenger are designed to deploy only in moderate to severe frontal and near frontal crashes. They are not designed to in???ate in rollover, rear or
CAUTION: (Continued)
CAUTION: (Continued)
And, for some unrestrained occupants, frontal airbags may provide less protection in frontal crashes than more forceful airbags have provided in the past. The
{CAUTION:
Both frontal and side impact airbags in???ate with great force, faster than the blink of an eye. If you are too close to an in???ating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag in???ation before and during a crash. Always wear your safety belt even with frontal airbags. The driver should sit as far back as possible while still maintaining control of the vehicle. Occupants should not lean on or sleep against the door.
{CAUTION:
Anyone who is up against, or very close to, any airbag when it in???ates can be seriously injured or killed. Airbags plus
The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page
The driver???s airbag is in the middle of the steering wheel.
The right front passenger???s airbag is in the instrument panel on the passenger???s side.
If your vehicle has a
If your vehicle has a
{CAUTION:
If something is between an occupant and an airbag, the bag might not in???ate properly or it might force the object into that person causing severe injury or even death. The path of an in???ating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. If your vehicle has side impact airbags, never secure anything to the roof of your vehicle by routing the rope or tiedown through any door or window opening. If you do, the path of an in???ating side impact airbag will be blocked. The path of an in???ating airbag must be kept clear.
When Should an Airbag In???ate?
The driver???s and right front passenger???s frontal airbags are designed to in???ate in moderate to severe frontal or
In addition, your vehicle has ???dual stage??? frontal airbags, which adjust the restraint according to crash severity. Your vehicle is equipped with electronic frontal sensors which help the sensing system distinguish between a moderate and a more severe frontal impact. For moderate frontal impacts, these airbags in???ate at a level less than full deployment. For more severe frontal impacts, full deployment occurs. If the front of your vehicle goes straight into a wall that doesn???t move or deform, the threshold level for the reduced deployment is about 12 to 16 mph (19.3 to 26 km/h), and the threshold level for a full deployment is about 20 to 24 mph
(32.2 to 38.5 km/h). (The threshold level can vary, however, with speci???c vehicle design, so that it can be somewhat above or below this range.)
Airbags may in???ate at different crash speeds. For example:
???If the vehicle hits a stationary object, the airbag could in???ate at a different crash speed than if the object were moving.
???If the object deforms, the airbag could in???ate at a different crash speed than if the object does not deform.
???If the vehicle hits a narrow object (like a pole) the airbag could in???ate at a different crash speed than if the vehicle hits a wide object (like a wall).
???If the vehicle goes into an object at an angle the airbag could in???ate at a different crash speed than if the vehicle goes straight into the object.
The frontal airbags (driver and right front passenger) are not intended to in???ate during vehicle rollovers, rear impacts, or in many side impacts because in???ation
would not likely help the occupants.
If your vehicle has side impact airbags, it has electronic side sensors. The side impact airbags are designed
to in???ate in moderate to severe side crashes. A side impact airbag will in???ate if the crash severity is above the system???s designed ???threshold level???. The threshold level can vary with speci???c vehicle
design. Side impact airbags are not designed to in???ate in frontal or
Your vehicle has seat position sensors which enable the sensing system to monitor the position of the driver???s seat and the right front passenger???s seat. Seat position sensors provide information that is used to determine
if the airbags should deploy at a reduced level or at full deployment.
In any particular crash, no one can say whether an airbag should have in???ated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, in???ation is determined by
the angle of the impact and how quickly the vehicle slows down in frontal or
What Makes an Airbag In???ate?
In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. For both frontal and side impact airbags, the sensing system triggers a release of gas from the in???ator, which in???ates the airbag. The in???ator, airbag, and related hardware are all part of the airbag modules inside the steering wheel and in the instrument panel in front of the right front passenger. For vehicles with side impact airbags, the airbag modules are located in the ceiling of the vehicle, near the side windows.
How Does an Airbag Restrain?
In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle. The airbag supplements the protection provided by safety belts. Airbags distribute the force of the impact more evenly over the occupant???s upper body, stopping the occupant more gradually. But the frontal airbags would not help you in many types
of collisions, including rollovers, rear impacts, and many side impacts, primarily because an occupant???s motion is not toward the airbag.
Side impact airbags would not help you in many types of collisions, including frontal or near frontal collisions, rollovers, and rear impacts, primarily because an occupant???s motion is not toward those airbags. Airbags should never be regarded as anything more than a supplement to safety belts, and then only in moderate to severe frontal or
in moderate to severe side collisions for side impact airbags.
What Will You See After an Airbag
In???ates?
After an airbag in???ates, it quickly de???ates, so quickly that some people may not even realize the airbag in???ated. Some components of the airbag module ??? the steering wheel hub for the driver???s airbag, the instrument panel for the right front passenger???s bag or the ceiling of your vehicle near the side windows ??? will be hot for a short time. The parts of the bag that come into contact with you may be warm, but not too hot to touch. There will be some smoke and dust coming from the vents in the de???ated airbags. Airbag in???ation does not prevent the driver from seeing or being able to steer the vehicle, nor does it stop people from leaving the vehicle.
{CAUTION:
When an airbag in???ates, there is dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have breathing problems but can not get out of the vehicle after an airbag in???ates, then get fresh air by opening a window or a door. If you experience breathing problems following an airbag deployment, you should seek medical attention.
Your vehicle may have a feature that will automatically unlock the doors, turn the interior lamps on and ???ash the hazard warning ???ashers when the airbag in???ates (if battery power is available). You can lock the doors again by using the door lock. The interior lamps and hazard warning ???ashers will deactivate after approximately
15 minutes.
In many crashes severe enough to in???ate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag.
???Airbags are designed to in???ate only once. After an airbag in???ates, you will need some new parts for your airbag system. If you do not get them,
the airbag system will not be there to help protect you in another crash. A new system will include airbag modules and possibly other parts. The service manual for your vehicle covers the need to replace other parts.
???Your vehicle is equipped with a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Collection and Event Data Recorders on page
???Let only quali???ed technicians work on your airbag system. Improper service can mean that your airbag system will not work properly. See your dealer for service.
Notice: If you damage the covering for the driver???s or the right front passenger???s airbag, or the side impact airbag covering on the ceiling near the side windows, the airbag may not work properly. You may have to replace the airbag module in the steering wheel, both the airbag module and the instrument panel for the right front passenger???s airbag, or side impact airbag module and ceiling covering for the
Airbag Off Switch
Regular Cab Models and Extended Cab Models without Rear Seats
United States
Canada
If your vehicle is a regular cab model or an extended cab model without rear seats, it has a switch on
the instrument panel that you can use to turn off the right front passenger???s frontal airbag.
This switch should only be turned to the off position if the person in the right front passenger???s position is
a member of a passenger risk group identi???ed by the national government as follows:
Infant. An infant (less than 1 year old) must ride in the front seat because:
???my vehicle has no rear seat;
???my vehicle has a rear seat too small to accommodate a
???the infant has a medical condition which, according to the infant???s physician, makes it necessary for the infant to ride in the front seat so that the driver
can constantly monitor the child???s condition.
Child age 1 to 12. A child age 1 to 12 must ride in the front seat because:
???my vehicle has no rear seat;
???although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no
space is available in the rear seat(s) of my vehicle; or
???the child has a medical condition which, according to the child???s physician, makes it necessary for the child to ride in the front seat so that the driver
can constantly monitor the child???s condition.
Medical Condition. A passenger has a medical condition which, according to his or her physician:
???causes the passenger airbag to pose a special risk for the passenger; and
???makes the potential harm from the passenger airbag in a crash greater than the potential
harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
{CAUTION:
If the right front passenger???s frontal airbag is turned off for a person who is not in a risk group identi???ed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag would not be able to in???ate and help protect the person sitting there. Do not turn off the passenger???s frontal airbag unless the person sitting there is in a risk group.
To turn off the right front passenger???s frontal airbag, insert your ignition key into the switch, push in,
and move the switch to the off position.
The airbag off light will come on to let you know that the right front passenger???s frontal airbag is off. The light
will stay on to remind you that the airbag is off. The right front passenger???s frontal airbag will remain off until
you turn it back on.
{CAUTION:
If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger???s frontal airbag could in???ate even though the switch is off. If this ever happens, do not let anyone whom the national government has identi???ed as a member of a passenger airbag risk group sit in the right front passenger???s position (for example, do not secure a
To turn on the right front passenger???s frontal airbag, insert your ignition key into the switch, push in,
and move the switch to the on position.
Servicing Your
Vehicle
Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see
Service Publications Ordering Information on page
{CAUTION:
For up to 10 seconds after the ignition key is turned off and the battery is disconnected, an airbag can still in???ate during improper service. You can be injured if you are close to an airbag when it in???ates. Avoid wires wrapped with yellow tape or yellow connectors. They are probably part of the airbag system. Be sure to follow proper service procedures, and make sure the person performing work for you is quali???ed to do so.
The airbag system does not need regular maintenance.
Adding Equipment to Your
Q: Is there anything I might add to the front of the vehicle that could keep the airbags from working properly?
A: Yes. If you add things that change your vehicle???s frame, bumper system, front end sheet metal or height, they may keep the airbag system from working properly. Also, the airbag system may not work properly if you relocate any of the airbag sensors. If you have any questions about this, you should contact Customer Assistance before you modify your vehicle. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure on page
Restraint System Check
Checking Your Restraint Systems
Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors
and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away.
Also look for any opened or broken airbag covers, and have them repaired or replaced. (The airbag system does not need regular maintenance.)
Replacing Restraint System Parts
After a Crash
{CAUTION:
A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
If you have had a crash, do you need new belts or LATCH system parts?
After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be if worn during a more severe crash, then you need
new parts.
If the LATCH system was being used during a more severe crash, you may need new LATCH system parts.
If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt or LATCH system was not being used at the time of
the collision.
If an airbag in???ates, you will need to replace airbag system parts. See the part on the airbag system earlier in this section.
If the frontal airbags in???ate, you will also need to replace the driver???s and right front passenger???s safety belt retractor assembly. Be sure to do so. Then the new retractor assembly will be there to help protect you in
a collision.
After a crash you may need to replace the driver and front passenger???s safety belt retractor assemblies, even if the frontal airbags have not deployed. The driver
and front passenger???s safety belt retractor assemblies contain the safety belt pretensioners. Have your safety belt pretensioners checked if your vehicle has
been in a collision, or if your airbag readiness light stays on after you start your vehicle or while you are driving. See Airbag Readiness Light on page
Section 2 Features and Controls
Keys
{CAUTION:
Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
There is one
When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number.
The key code number tells your dealer or a quali???ed locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able
to have new ones made easily using this number. Your dealer should also have this number.
Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in.
Be sure you have spare keys.
If you ever do get locked out of your vehicle call the GM Roadside Assistance Center. See Roadside Assistance Program on page
If your vehicle is equipped with the OnStar system with an active subscription and you lock your keys inside the vehicle, OnStar may be able to send a command to unlock your vehicle. See OnStar?? System on page
Remote Keyless Entry System
If equipped, the keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.This device may not cause interference.
2.This device must accept any interference received, including interference that may cause undesired operation of the device.
This device complies with
1.This device may not cause interference.
2.This device must accept any interference received, including interference that may cause undesired operation of the device.
Changes or modi???cations to this system by other than an authorized service facility could void authorization to use this equipment.
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this:
???Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather.
???Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and
try again.
???Check to determine if battery replacement is necessary. See ???Battery Replacement??? under
Remote Keyless Entry System Operation on page
???If you are still having trouble, see your dealer or a quali???ed technician for service.
Remote Keyless Entry System
Operation
If your vehicle has this feature you can lock and unlock your doors and disarm or arm your
UNLOCK: Press this button to unlock the driver???s door and turn on the interior lamps. The parking lamps may also ???ash,
and the horn may chirp, when this button is pressed.
Press the unlock button again within three seconds and all of the doors will unlock.
LOCK: Press this button to lock all the doors. The parking lamps may also ???ash and the horn may chirp when this button is pressed. Press the button again within three seconds and the horn may chirp.
If a door is open or ajar when the lock button is pressed, the horn will chirp several times to let you know that
the doors did not lock and the content
the opened door is closed.
You can program different feedback modes through the Driver Information Center (DIC). To program the feedback modes, see ???Remote Keyless Entry Feedback??? under DIC Controls and Displays on page
L(Panic): Press this button to make the horn sound and the headlamps and taillamps ???ash for up to
30 seconds. To turn them off again, do one of these three things: wait for 30 seconds; press the panic button again; or start the vehicle.
Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can
be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched. Once your dealer has coded the new transmitter, the lost transmitter will not unlock
your vehicle. Each vehicle can have a maximum of four transmitters matched to it.
Under normal use, the battery in your remote keyless entry transmitter should last about two years.
You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have
to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter.
1. Insert a thin coin, or similar object, in the slot between the covers of the transmitter housing. Gently pry the transmitter apart.
2. Remove and replace the battery with a
3. Align the covers and snap them together.
4. Check the operation of the transmitter.
Doors and Locks
Door Locks
There are several ways to lock and unlock your vehicle.
To unlock the door from the outside, use the key or the remote keyless entry transmitter (if equipped).
{CAUTION:
Unlocked doors can be dangerous.
???Passengers ??? especially children ??? can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive.
???Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it.
???Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening.
To lock a door from the inside, push the manual lever on your door forward. To unlock a door from the inside, push the lever on the door rearward.
You will see a colored area on the lever when the door is unlocked.
Power Door Locks
If your vehicle has power door locks, the switches are located on the driver???s and the front passenger???s armrests.
Remove the ignition key and press L (lock) to lock all the doors at once. To unlock all the doors, press U (unlock).
On crew cab models, use the manual door lock lever on each rear door to lock or unlock the doors from the rear seating area.
Programmable Automatic Door
Locks
If your vehicle has power door locks and the remote keyless entry system, it will be equipped with an
auto lock/unlock feature which enables you to program your vehicle???s power door locks from the driver???s seating position.
If your vehicle has an automatic transmission, it will be programmed to have all the doors lock automatically when the shift lever is moved out of PARK (P). All the doors will unlock when the shift lever is moved back into PARK (P).
If your vehicle has a manual transmission, it will be programmed to have all the doors lock when the vehicle speed is greater than 15 mph (24 km/h). The doors
will unlock when the key is removed from the ignition.
To personalize the automatic door locks, see ???Automatic Door Locks??? under DIC Controls and Displays on
page
Rear Door Security Locks
(Crew Cab)
If you have the crew cab model, your vehicle may be equipped with rear door security locks. With this feature, you can lock the rear doors so they cannot be opened from the inside by passengers.
The security lock lever is located on the inside edge of each rear door.
To use the security locks, do the following:
1.Open one of the rear doors.
2.Using your ignition key, turn the lock clockwise on the driver???s side rear door, and counterclockwise on the passenger???s side rear door to engage the
rear door security lock.
3.Close the door.
4.Repeat these steps on the opposite rear door.
If you want to open the rear door when the security lock is on, unlock the door and open the door from the outside. To return the rear doors to normal use, disengage the locks by inserting the ignition key and turning the lock counterclockwise for the driver???s side rear door, and clockwise for the passenger???s side rear door.
Lockout Protection
If you have power door locks, this feature protects you from locking your key in the vehicle when the key is in the ignition and a door is open.
If the power door lock switch is pressed when a door is open and the key is in the ignition, all of the doors
will lock and then the driver???s door will unlock.
Rear Doors (Extended Cab)
If you have an extended cab, your vehicle has rear doors for convenience in loading and unloading cargo.
To open a rear door, open the front door. Then, use the handle located on the front edge of the rear door panel to open it. You must close the rear door before closing the front door.
Tailgate
You can open the tailgate by pulling up on the handle while pulling the tailgate down.
When you put the tailgate back up, be sure it latches securely.
You can lock the tailgate using your ignition key. Turn the key counterclockwise to lock the tailgate. Turn the key clockwise to unlock the tailgate.
Removing the Tailgate
Follow these steps if you want to remove the tailgate:
1. Lift up slightly on the entire tailgate assembly.
Remove the retaining cables from both ends of the tailgate by pulling upward on the clip. Then, push forward so the larger part of the hole on the bracket is over the bolt. Pull the end over the bolt.
2.With the tailgate partially down, pull the tailgate toward you at the passenger???s side and then
move the tailgate to the right to release the driver???s side. You can then remove the entire tailgate assembly.
Reverse the procedure to reinstall the tailgate. Make sure it is secure.
To partially lower the tailgate do the following:
1.Lift up slightly on the entire tailgate assembly.
2.Pull upward on each clip. Then, push forward so the larger part of the hole on the bracket is over the bolt. Pull the end
over the bolt.
Tailgate Partially Down
3.Slide the end ???tting off the bottom bolt and onto the top bolt. The tailgate will now stay in the partially opened position.
If you would like to close the tailgate, the bracket cannot be in the partially opened position and must be anchored on the bottom bolt, using the secondary position on the end ???tting.
Windows
{CAUTION:
Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Manual Windows
On a vehicle with manual windows, use the handle on each door to open and close each window.
Power Windows
The power window controls are located on the armrest of each door.
Crew cab switches shown
The driver???s door has switches for the passenger windows as well. Your power windows will work when the ignition has been turned to ACC (Accessory) or ON or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page
Pull up the forward edge of the control with the power window symbol on it to raise the window.
Press the forward edge of the control down to lower the window.
Do not hold all four power window switches down for several seconds after the windows have been completely lowered or raised, because the vehicle may blow a fuse.
Express Down Windows
The driver???s window also has an
the ???rst position to activate the
the window is at the desired position.
Window Lockout
If you have a crew cab vehicle with power windows, you will also have a window lockout button located above the window switches. This feature disables the passenger???s window switches when the window lockout button is pressed. To turn the lockout feature on or
off, press the window lockout button. A red band on the side of the button can be seen when the windows
are not locked out.
Sliding Rear Window
If your vehicle has this feature, squeeze the latch in the center of the window and slide the glass to open it.
When you close the window, be sure the latch is engaged.
Sun Visors
To block glare, pull the visor down. It can also be detached from the center mount and moved to the side to block glare from that direction.
Visor Vanity Mirror
The passenger???s side sun visor has a mirror on it. Pull down the visor to access the mirror.
Vehicle theft is big business, especially in some cities. Although your vehicle has a number of
Content
If your vehicle has the remote keyless entry system, the vehicle has a content
To activate the content
1.Close all the doors.
2.Lock the door with the remote keyless entry transmitter. The security light ???ashes.
If the lock button on the remote keyless entry transmitter is pressed, but a door is open, the horn will chirp six times. Close the open door and the system will be activated.
If a locked door is not opened using the remote keyless entry transmitter, or by OnStar??, the alarm will go off. The front turn signal lamps will ???ash for two minutes, and the horn will sound for two minutes, then will turn off to save the battery power.
Remember, the
be activated using the remote keyless entry transmitter, or by OnStar??. You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off.
Here???s how to avoid setting off the alarm by accident:
???If you don???t want to activate the
???Always unlock a door with the remote keyless entry transmitter. Unlocking a door any other way will set off the alarm.
If you set off the alarm by accident, you can turn off the alarm by pressing unlock on the remote keyless entry transmitter. The alarm won???t stop if you try to unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1.From inside the vehicle, activate the system by locking the doors with the remote keyless entry transmitter.
2.Unlock the door with the manual door lock and open the door. This should set off the alarm.
3.To turn the alarm off, press the unlock button on the remote keyless entry transmitter or start the engine.
If the alarm does not sound when it should but the lights ???ash, check to see if the horn works. The horn fuse
may be blown. To replace the fuse, see Fuses and Circuit Breakers on page
If the alarm does not sound or the headlamps do not ???ash, see your dealer for service.
Passlock??
Your vehicle is equipped with the Passlock??
Passlock?? is a passive
a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, the fuel system is disabled and the vehicle will not start.
During normal operation, the security light will turn off approximately ???ve seconds after the key is turned to ON. See Security Light on page
If the engine stalls and the security light ???ashes, wait about 10 minutes until the light stops ???ashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts.
If the engine does not start after three tries, the vehicle needs service.
If the engine is running and the security light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock?? system is
not working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock?? at this time. See your GM dealer for service.
In an emergency, call the GM Roadside Assistance Center. See Roadside Assistance Program on page
Starting and Operating Your
Vehicle
New Vehicle
Notice: Your vehicle does not need an elaborate
???Keep your speed at 55 mph (88 km/h) or less for the ???rst 500 miles (805 km).
???Do not drive at any one speed ??? fast or
slow ??? for the ???rst 500 miles (805 km). Do not make
???Avoid making hard stops for the ???rst
200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this
???Do not tow a trailer during
Ignition Positions
With the key in the ignition switch, you can turn to four different positions.
LOCK (A): This position locks your ignition and transmission on manual transmission vehicles. It is a
If you have a manual transmission, the ignition switch cannot be turned to LOCK unless the shift lever is
in PARK (P).
Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is all the way in. If
it is, turn the steering wheel left and right while you turn the key hard. If none of this works, then
your vehicle needs service.
ACC (ACCESSORY) (B): This is the position in which you can operate your electrical accessories or items plugged into the accessory power outlets. It also unlocks the steering wheel and ignition. Use this position if
your vehicle must be pushed or towed.
ON (C): This is the position that the switch returns to after you start your engine and release the switch. The switch stays in ON when the engine is running. But even when the engine is not running, you can use ON to operate your electrical accessories and to display some instrument panel cluster warning and indicator lights.
START (D): This is the position that starts the engine. When the engine starts, release the key. The ignition switch will return to ON for normal driving.
When the engine is not running, ACC and ON allow you to operate your electrical accessories, such as the radio or items plugged into the accessory power outlets.
A warning tone will sound if you open the driver???s door when the ignition is in ACC or LOCK and the key is in the ignition.
Retained Accessory Power (RAP)
Your vehicle is equipped with Retained Accessory Power (RAP) which will allow certain features of your vehicle to continue working for up to 20 minutes after the ignition key is turned to LOCK.
Your radio and power windows will work when the ignition key is in ON or ACC. Once the key is turned from ON to LOCK, these features will continue to work for up to 20 minutes or until a door is opened.
Starting Your Engine
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position ??? that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only.
Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped.
Manual Transmission
The gear selector should be in NEUTRAL and the parking brake engaged. Hold the clutch pedal to the ???oor and start the engine. Your vehicle will not start if the clutch pedal is not all the way down ??? that is a safety feature.
Starting Your Engine
1.With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm.
Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter.
2.If the engine does not start within 10 seconds, push the accelerator pedal all the way to the ???oor, while you hold the ignition key in START. When the engine starts, let go of the key and let up on the accelerator pedal. Wait about 15 seconds between each try.
Depending on the outside temperature, the engine starter may continue cranking the engine up to approximately four seconds after you release the ignition key. This is normal.
When starting your engine in very cold weather (below 0??F or 18??C), do this:
1.With your foot off the accelerator pedal, turn the ignition key to START and hold it there up to 15 seconds. When the engine starts, let go of the key.
2.If your engine still will not start, or starts but then stops, it could be ???ooded with too much gasoline. Try pushing your accelerator pedal all the way to the ???oor and holding it there as you hold the key in START for about three seconds. When the engine starts, let go of the key and accelerator. If the vehicle starts brie???y but then stops again, do the same thing, but this time keep the pedal down
for ???ve or six seconds. This clears the extra gasoline from the engine.
Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly.
Engine Coolant Heater
Your vehicle may be equipped with this feature.
In very cold weather, 0??F
To Use the Engine Coolant Heater
1.Turn off the engine.
2.Open the hood and unwrap the electrical cord. The cord is located in the engine compartment behind the underhood fuse block on the driver???s side of the vehicle.
3.Plug it into a normal, grounded
{CAUTION:
Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ???re. You could be seriously injured. Plug the cord into a properly grounded
4.Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged.
How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead
of trying to list everything here, we ask that you contact your dealer in the area where you will be parking
your vehicle. The dealer can give you the best advice for that particular area.
Automatic Transmission Operation
Your automatic transmission has a shift lever on the steering column.
It features an electronic shift position indicator within the instrument cluster. This display must be powered anytime the shift lever is capable of being moved out of PARK (P). This means that if your key is turned off,
but not in LOCK, there will be a small current drain on your battery which could discharge your battery over a period of time.
If you need to leave your key in the ignition but not in LOCK for an extended period, it is recommended
that you disconnect the battery cable from the battery to prevent discharging your battery.
There are several different positions for your shift lever.
PARK (P): This position locks your rear wheels. It is the best position to use when you start your engine because your vehicle cannot move easily.
{CAUTION:
It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ???rmly set. Your vehicle can roll.
Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) (Automatic Transmission) on page
Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition key is in ON. If you cannot shift out of PARK (P), ease pressure on the shift
lever by pushing the shift lever all the way into PARK (P) as you maintain brake application. Then move the
shift lever into the gear you want. See Shifting Out of Park (P) (Automatic Transmission) on page
REVERSE (R): Use this gear to back up.
Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transmission,
see If You Are Stuck: In Sand, Mud, Ice or Snow on page
NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only.
{CAUTION:
Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ???rmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed.
Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be
covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle.
DRIVE (D): This position is for normal driving. If you need more power for passing, and you are:
???Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down.
???Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
You will shift down to the next gear and have more power.
DRIVE (D) should not be used when towing a trailer, carrying a heavy load, driving on steep hills, or for
THIRD (3): This position is also used for normal driving. However, it offers more power and lower fuel economy than DRIVE (D). You should use THIRD (3) when towing a trailer, carrying a heavy load, driving on steep hills
or winding roads or for
SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. You can also use SECOND (2) for starting your vehicle from a stop on slippery road surfaces.
FIRST (1): This position gives you even more power but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1) while the vehicle is moving forward, the transmission will not shift into FIRST (1) until the vehicle is going slowly enough.
Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.
Manual Transmission Operation
This is your shift pattern.
Here is how to operate your manual transmission:
FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal as you slowly press down on the accelerator pedal.
You can shift into FIRST (1) when you are going less than 20 mph (30 km/h). If you have come to a complete stop and it is hard to shift into FIRST (1), put the shift lever in NEUTRAL and let up on the clutch. Then press the clutch pedal back down and shift into FIRST (1).
SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2).
Then, slowly let up on the clutch pedal as you press the accelerator pedal.
THIRD, FOURTH AND FIFTH (3, 4 and 5): Shift into THIRD (3), FOURTH (4) and FIFTH (5) the same
way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal.
To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to NEUTRAL.
NEUTRAL: Use this position when you start or idle your engine.
REVERSE (R): To back up, press the clutch pedal. After the vehicle stops, shift into REVERSE (R). Slowly let up on the clutch pedal as you press the accelerator pedal. If it is hard to shift, let the shift lever return to NEUTRAL and release the clutch pedal. Then press the clutch again and shift into REVERSE (R). Do not attempt to shift into the ???fth gear position prior to shifting into REVERSE (R). Your transmission has a lock out feature which prevents a ???fth gear to reverse gear shift.
Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
Use REVERSE (R), along with the parking brake, for parking your vehicle.
This light will show you when to shift to the next higher gear for best fuel economy.
When this light comes on, you can shift to the next higher gear if weather, road and traffic conditions permit. For the best fuel economy, accelerate slowly and shift when the light comes on.
While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator. Ignore the shift light when you downshift.
If your vehicle has
For more information, see
Notice: Driving on clean, dry pavement in
Shift Speeds
{CAUTION:
If you skip a gear when you downshift, you could lose control of your vehicle. You could injure yourself or others. Don???t shift down more than one gear at a time when you downshift.
If your vehicle has
The transfer case buttons are located to the right of the steering wheel on the instrument panel.
Use these buttons to shift into and out of
N (Neutral): Shift the vehicle???s transfer case to NEUTRAL only when towing your vehicle.
{CAUTION:
Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in NEUTRAL. See Parking Brake on page
icy roads, or in most
Indicator lights in the buttons show you which setting you are in. The indicator lights will come on brie???y when you turn on the ignition and one will stay on. If the lights do not come on, you should take your vehicle in for service. An indicator light will ???ash while shifting.
It will remain illuminated when the shift is completed.
If for some reason the transfer case cannot make
a requested shift, it will return to the last chosen setting.
Shifting from
Press and release the
Shifting from
Press and release the
Shifting from
To shift from
equipped with a manual transmission. The preferred method for shifting into
If the
1.2 mph (2 km/h), the
On automatic transmission equipped vehicles, if your transfer case does not shift into
Shifting from
To shift from
and release the
If the
On vehicles with an automatic transmission, if your transfer case does not shift into
Shifting to NEUTRAL
Use NEUTRAL when you plan to tow your vehicle. See
Recreational Vehicle Towing on page
1.Set the parking brake.
2.Start the vehicle.
3.Shift the transmission in NEUTRAL (N), or press in the clutch for vehicles with a manual transmission.
4.Shift the transfer case to
5.Press and hold the
6.Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, or FIRST (1) for vehicles with manual transmissions.
7.Turn the ignition to LOCK.
8.Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles equipped with a manual transmission.
Shifting Out of NEUTRAL
After towing your vehicle, you will have to shift out of NEUTRAL in order to drive. To shift out of NEUTRAL, do the following:
1.Set the parking brake and apply the regular brake pedal. See Parking Brake on page
2.Start a vehicle with an automatic transmission in PARK (P). Use FIRST (1) for vehicles with a manual transmission.
3.Put an automatic transmission in NEUTRAL (N) or press the clutch pedal for vehicles with a manual transmission.
4.Press the button for the desired transfer case position
5.After the transfer case has shifted out of NEUTRAL, the indicator light will go out.
6.Release the parking brake.
7.Shift the transmission to the desired gear.
It is normal for your vehicle to exhibit a signi???cant engagement noise and bump when shifting in and out of Neutral (N) and
Parking Brake
The parking brake pedal is located to the left of the regular brake pedal,
near the driver???s door.
To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot.
A chime will activate and the warning light will ???ash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at least three
seconds. The chime will deactivate and the light will turn off when the parking brake is set and the vehicle is moving below 3 mph (5 km/h). See Brake System Warning Light on page
To release the parking brake, hold the regular brake pedal down. Pull the bottom edge of the lever, located above the parking brake pedal, with the parking
brake symbol, to release the parking brake.
If the ignition is on when the parking brake is released, the brake system warning light will go off.
Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving.
If you are towing a trailer and are parking on any hill, see Towing a Trailer on page
Shifting Into Park (P) (Automatic
Transmission)
{CAUTION:
It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ???rmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page
1.Hold the brake pedal down with your right foot and set the parking brake.
{CAUTION:
If you have
in PARK (P) ??? if your transfer case is in NEUTRAL. So, be sure the transfer case is in a drive gear,
NEUTRAL.
2.Move the shift lever into PARK (P) by pulling the lever toward you and moving it up as far as it will go.
3.Turn the ignition key to LOCK.
4.Remove the key and take it with you. If you can leave your vehicle with the key, your vehicle is in PARK (P).
Leaving Your Vehicle With the Engine
Running
{CAUTION:
It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in
PARK (P) with the parking brake ???rmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ???re. You or others could be injured. Do not leave your vehicle with the engine running.
If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ???rmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ???rst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P).
Torque Lock
If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ???nd it difficult to pull the shift lever out of PARK (P). This is called ???torque lock.??? To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver???s seat.
To ???nd out how, see Shifting Into Park (P) (Automatic Transmission) on page
When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake.
If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P).
Shifting Out of Park (P) (Automatic
Transmission)
Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK (P) when the ignition is in the LOCK position. In addition, you have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transmission Operation on page
If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing the shift lever all the way into PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want.
If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this:
1.Turn the key to ACC. There is no shift interlock in this key position.
2.Apply and hold the brake until the end of Step 4.
3.Shift the transmission to NEUTRAL (N).
4.Start the vehicle and then shift to the gear you want.
5.Have the system ???xed as soon as you can.
Parking Your Vehicle (Manual
Transmission)
Your vehicle has a manual transmission. Before you get out of your vehicle, move the shift lever into
REVERSE (R), and ???rmly apply the parking brake. Once the shift lever has been placed into REVERSE (R)
with the clutch pedal pressed in, you can turn the ignition key to LOCK, remove the key and release the clutch.
If you are parking on a hill, or if your vehicle is pulling a trailer, see Towing a Trailer on page
Parking Over Things That Burn
{CAUTION:
Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn.
Engine Exhaust
{CAUTION:
Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death.
You might have exhaust coming in if:
???Your exhaust system sounds strange or different.
???Your vehicle gets rusty underneath.
???Your vehicle was damaged in a collision.
???Your vehicle was damaged when driving over high points on the road or over road debris.
???Repairs were not done correctly.
???Your vehicle or exhaust system had been modi???ed improperly.
If you ever suspect exhaust is coming into your vehicle:
???Drive it only with all the windows down to blow out any CO; and
???Have your vehicle ???xed immediately.
Running Your Engine While You
Are Parked (Automatic
Transmission)
It is better not to park with the engine running. But if you ever have to, here are some things to know.
{CAUTION:
Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under
Engine Exhaust on page
Also, idling in a
NEVER park in a garage with the engine running.
Another
Winter Driving on page
{CAUTION:
It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ???rmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
{CAUTION:
If you have
Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) (Automatic Transmission) on page
If you are pulling a trailer, see Towing a Trailer on page
Mirrors
Manual Rearview Mirror
While sitting in a comfortable driving position, adjust the outside rearview mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The control at the bottom
of the mirror is the day/night feature that allows adjustment to the mirror so that the glare of headlamps from behind is reduced. Push the control for daytime use; pull it for night use.
The mirror may have lamps. Press the button next to each lamp to turn it on or off.
Manual Rearview Mirror with OnStar??
Your vehicle may have a manual rearview mirror with the OnStar?? System and map lamps.
Mirror Operation
You can adjust the mirror for day or night driving. Press the tab forward (away from you) for day driving. Pull the tab back (toward you) for night driving.
There are also three OnStar?? buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar??. See OnStar?? System on page
Map Lamps
The mirror has map lamps located at the bottom of the mirror. To manually turn the lamps on or off, press
the button next to each lamp.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror housing.
Automatic Dimming Rearview Mirror with Compass and Temperature Display
The vehicle may have an automatic dimming rearview mirror with a compass, temperature display, and
map lamps.
Mirror Operation
The mirror automatically changes to reduce glare from headlamps behind you. A time delay feature prevents rapid changing from the day to night positions while driving under lights and through traffic.
P(On/Off): The automatic dimming feature is automatically activated when the vehicle is started. The automatic dimming feature is turned on or off by pressing this button located on the lower part of the mirror. Press and hold the button for up to three seconds to turn this feature on or off.
T(Indicator Light): This light will turn on when the automatic dimming feature is active.
Map Lamps
The mirror has map lamps located at the bottom of the mirror. To manually turn the lamps on or off, press
the button next to each lamp.
Compass Operation
The mirror has an
When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the current compass heading.
For example, NE is displayed for
Compass Calibration
If after two seconds the display does not show a compass heading, there may be a strong magnetic ???eld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note
pad holder or similar object. If the letter C appears in the compass window, the compass needs calibration.
The mirror compass can be calibrated by driving
the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction.
The compass can be placed in calibration mode by pressing and holding the left map light button until a C appears on the compass display.
Compass Variance
Compass variance is the difference between earth???s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, your compass could give false readings.
The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as a long distance,
To adjust for compass variance, do the following:
1.Find your current location and variance zone number on the zone map that follows.
2. Press and hold the left map light button until a zone number appears on the display.
3. Once the zone number appears on the display, press the on/off button quickly until you reach
the correct zone number. Stop pressing the button and the mirror will return to normal operation.
If C appears in the compass window, the compass may need calibration. See ???Compass Calibration??? listed previously.
Temperature Display Operation
The outside air temperature is displayed in the window located at the lower center of the mirror face.
Press and hold the far right button for four seconds and release. This will change the temperature reading between degrees Fahrenheit, degrees Celsius, or turn the display off.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.
Outside Manual Mirrors
If the vehicle has manual outside mirrors, adjust them by hand so that the side of the vehicle can be seen while you are sitting in a comfortable driving position.
The mirrors can be folded inward to prevent damage when going through an automatic car wash. To
fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Return both mirrors to the unfolded position before driving.
Outside Power Mirrors
If your vehicle has this feature, the controls are located on the driver???s door armrest.
To adjust the power mirrors, do the following:
1.Move the selector switch to the L (left) or R (right) to choose the driver???s or passenger???s mirror.
2.Use the arrows located on the
3.Return the selector switch to the center position once the mirrors are adjusted.
If the mirror begins making a ratcheting sound, the mirror has reached the end of its travel and can go no farther in that direction. To stop the sound, reverse the mirror direction using the control pad.
The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure
to return both mirrors to the unfolded position before driving.
Outside Convex Mirror
Your passenger???s outside rearview mirror is convex. A convex mirror???s surface is curved so you can see more from the driver???s seat.
{CAUTION:
A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.
OnStar?? System
OnStar?? uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services.
A complete OnStar?? user???s guide and the terms and conditions of the OnStar?? Subscription Service Agreement are included in the vehicle???s glove box literature. For more information, visit www.onstar.com or www.onstarcanada.com. Contact OnStar?? at
Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com.
OnStar?? Services
For new vehicles equipped with OnStar??, the Safe and Sound Plan is included for the ???rst year. You can extend this plan beyond the ???rst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar?? button to speak with an advisor.
Safe and Sound Plan
???Automatic Noti???cation of Airbag Deployment
???Emergency Services
???Roadside Assistance
???Stolen Vehicle Tracking
???AccidentAssist
???Remote Door Unlock/Vehicle Alert
???Remote Diagnostics
???Online Concierge
Directions and Connections Plan
???All Safe and Sound Plan Services
???Driving Directions
???RideAssist
???Information and Convenience Services
OnStar?? Personal Calling
As an OnStar?? subscriber, the Personal Calling capability is available if your
commands with no additional contracts and no additional roaming charges. To ???nd out more about OnStar ?? Personal Calling, refer to the OnStar?? user???s guide in the vehicle???s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar?? advisor by pressing the OnStar?? button or by calling
OnStar?? Virtual Advisor
Virtual Advisor is a feature of OnStar?? Personal Calling that uses minutes to access
Storage Areas
Glove Box
To open the glove box, pull on the lever.
Cupholder(s)
Your vehicle may have two cupholders located on the lower part of the front doors as well as two cupholders located at the front end of the console. Vehicles
with bench seats may have cupholders attached to the front of the center seat.
If your vehicle is an extended cab or crew cab model, your vehicle also has two rear cupholders. On crew cab models, the cupholders are located at the front end
of the rear center seat cushion. On extended cab models, the rear seat cupholders are located on top of the rear center console.
Once the ashtray is removed you may be able to use the area as a cupholder.
Front Armrest Storage Area
For vehicles with bench seats, you may have a center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to open the storage area.
For vehicles with bucket seats or uplevel packages, your vehicle may have a
To close the storage area(s), lower the lid(s) until you feel the latch close.
Assist Handles
Your vehicle may have assist handles to be used when getting out of your vehicle. If your vehicle has assist handles, they may be located above the front passenger door if you have a regular cab, or above the front and rear passenger doors if you have an extended cab
or crew cab.
If your vehicle is equipped with
Rear Storage Area
If your vehicle is an extended cab model, it may be equipped with storage compartments under the rear seats.
To access the storage compartments you will need to lift the cushion on the bottom of the rear seats. This will expose the storage boxes under the seat.
Lift the lid to access the storage box.
To open a storage box, unhook the bottom of the latches and lift the two latches on each side of the storage box.
??? NOTES
Section 3 Instrument Panel
??? NOTES
Instrument Panel Overview
Manual Transmission shown, Automatic Transmission similar
The main components of your vehicle???s instrument panel are the following:
A.Air Outlets. See Outlet Adjustment on page
B.Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page
C.Instrument Panel Cluster. See Instrument Panel Cluster on page
D.Hazard Warning Flasher Button. See Hazard Warning Flashers on page
E.Passenger Side Airbag. See Airbag System on page
F.Exterior Lamp Controls. See Exterior Lamps on page
Exterior Cargo Lamps on page
G.Parking Brake Release. See Parking Brake on page
H.Horn. See Horn on page
I.Traction Control Button or
and
J.Audio System. See Audio System(s) on page
K.Cigarette Lighter (If Equipped). See Ashtrays and Cigarette Lighter on page
L.Climate Control System. See Climate Control System on page
M.Accessory Power Outlet. See Accessory Power Outlets on page
N.Airbag Off Switch (Regular cab and rear seat delete only). See Airbag Off Switch on page
O.Glove Box. See Glove Box on page
Hazard Warning Flashers
Your hazard warning ???ashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ???ash on and off.
The hazard warning ???asher button is located on the instrument panel, between the two air vents in the center.
Your hazard warning ???ashers work no matter what position your key is in, and even if the key isn???t in.
Press the button to make the front and rear turn signal lamps ???ash on and off. Press the button again to
turn the ???ashers off.
When the hazard warning ???ashers are on, your turn signals won???t work.
Other Warning Devices
If you carry re???ective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle.
Horn
To sound the horn, press the horn symbol on the steering wheel pad.
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel before you drive. If you have the tilt steering wheel, you can raise it to the highest level to allow more room
for the driver to enter and exit the vehicle.
The tilt lever is located on the left side of the steering column, under the turn signal lever.
To tilt, hold the steering wheel and pull the tilt lever toward you. Move the wheel to a comfortable level, then release the tilt lever to lock the wheel in place.
Do not adjust the steering wheel while driving.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column includes the following:
??? GTurn and Lane Change Signals. See Turn Signal/Multifunction Lever on page
??? 53Headlamp
Headlamp
???
???NWindshield Wipers. See Windshield Wipers on page
???LWindshield Washer. See Windshield Washer on page
???JCruise Control. See Cruise Control on page
Turn and
The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down. When the turn is ???nished, the lever will return automatically.
To signal a lane change, just raise or lower the lever until the arrow starts to ???ash. Hold it there until you complete your lane change. The lever will return by itself when you release it.
An arrow on the instrument panel cluster will ???ash in the direction of the
turn or lane change.
As you signal a turn or a lane change, if the arrows ???ash more quickly than normal, a signal bulb may be burned out and other drivers won???t see your turn signal.
If a bulb is burned out, replace it to help avoid an accident. If the arrows don???t go on at all when you signal a turn, check for
Fuses and Circuit Breakers.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ???ash of the turn signal and the message TURN SIGNAL will
also appear in the DIC. To turn the chime and message off, move the turn signal lever to the off position.
See ???TURN SIGNAL??? under DIC Warnings and Messages on page
Headlamp
53(Headlamp High/Low Beam Changer): To
change the headlamps from low to high beam, push the lever toward the instrument panel. To return to
When the high beams are on, this indicator light on the instrument panel cluster will also be on.
This feature lets you use your
It works even if your headlamps are in the automatic position.
To use it, pull the turn signal lever toward you, then release it.
If your headlamps are in the automatic position or on low beam, your
cluster will come on. Release the lever to return to normal operation.
Windshield Wipers
You control the windshield wipers by turning the band with the wiper symbol on it.
8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more
wipes, hold the band on mist longer.
N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful
in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter
the delay.
6(Low Speed): For steady wiping at low speed, turn the band away from you to the ???rst solid position past the delay settings.
1(High Speed): For
9(Off): To stop the wipers, move the band to off.
Be sure to clear ice and snow from the wiper blades before using them. If they???re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts.
Windshield Washer
{CAUTION:
In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ???uid can form ice on the windshield, blocking your vision.
QL(Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ???uid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed.
Cruise Control
Your vehicle may be equipped with cruise control.
9(Off): This position turns the system off.
R(On): This position activates the system.
+ (Resume/Accelerate): Move the lever to this symbol to make the vehicle accelerate or resume to a previously set speed.
rT(Set): Press this button to set the speed.
With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long
trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Cruise control will not work if your parking brake is set, or if the master cylinder brake ???uid level is low.
If you apply your brakes, the cruise control will shut off.
{CAUTION:
Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic.
Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads.
If your vehicle is in cruise control when the traction control system (if equipped) begins to limit wheel spin, the cruise control will automatically disengage. See
Traction Control System (TCS) on page
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
1.Move the cruise control switch to on.
2.Get up to the speed you want.
3.Press in the set button at the end of the lever and release it.
4.Take your foot off the accelerator pedal.
The cruise symbol on the instrument panel will illuminate when the cruise control is engaged.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don???t need to reset it.
Once you???re going about 25 mph (40 km/h) or more, you can move the cruise control switch brie???y from on to resume/accelerate.
You???ll go right back up to your chosen speed and stay there.
If you hold the switch at resume/accelerate the vehicle will keep going faster until you release the switch or apply the brake. So unless you want to go faster, don???t hold the switch at resume/accelerate.
Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed:
???Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator
pedal. You???ll now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off.
???Move the cruise switch from on to resume/accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch brie???y to resume/accelerate. Each time you do this, your vehicle will go about
1 mph (1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
???Press and hold the set button until you reach the lower speed you want, then release it.
???To slow down in very small amounts, brie???y press the set button. Each time you do this, you???ll go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends upon your speed, load and the steepness of the
hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ???nd this to be too much trouble and don???t use cruise control on steep hills.
Ending Cruise Control
To turn off the cruise control, do one of the following:
???Step lightly on the brake pedal.
???Move the cruise control switch to off.
???Lightly tap or press the clutch, if you have a manual transmission.
Erasing Speed Memory
When you turn off the cruise control or the ignition, your cruise control set speed memory is erased.
Exterior Lamps
The control on the driver???s side of your instrument panel operates the exterior lamps.
O(Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions.
9(Off): Turn the knob to this position to turn off all exterior lamps including the DRLs.
AUTO: Turn the knob to this position to automatically turn on the headlamps at normal brightness, together with the following:
???Sidemarker Lamps
???Taillamps
???Parking Lamps
???Instrument Panel Lights
See Automatic Headlamp System on page
;(Parking Lamps): Turn the knob to this position to turn on the parking lamps, together with the following:
???Sidemarker Lamps
???Taillamps
???License Plate Lamps
???Instrument Panel Lights
2(Headlamps): Turn the knob to this position to turn on the headlamps, together with the previously listed lamps and lights.
You can switch your headlamps from low to high beam by pushing the turn signal/multifunction lever toward the instrument panel.
Headlamps on Reminder
If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and your key is out of the ignition. To turn off
the chime, turn the headlamp switch to off and then back on. In the automatic mode, the headlamps turn off once the ignition is in LOCK.
When the DRL are on, only your DRL lamps will be on. The taillamps, sidemarkers and other lamps will not
be on. The instrument panel will not be lit up either.
When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps.
As with any vehicle, you should turn on the regular headlamp system when you need it.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the
day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles
???rst sold in Canada.
The DRL system will come on when the following conditions are met:
???The ignition is on.
???The exterior lamps control is in AUTO.
???The transmission is not in PARK (P) if you have an automatic transmission or the parking brake is not set if you have a manual transmission.
???The light sensor determines it is daytime.
Automatic Headlamp System
When it is dark enough outside, your automatic headlamp system will turn on your headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, roof marker lamps and the instrument panel lights. The radio lights will also be dim.
Your vehicle has a light sensor located on the top of the instrument panel. Be sure it is not covered, or the system will be on whenever the ignition is on.
The system may also turn on your headlamps when driving through a parking garage, heavy overcast weather or a tunnel. This is normal.
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the
light sensor sees a change in lighting lasting longer than the delay.
If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately. Once
you leave the garage, it will take approximately one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, your instrument panel cluster may not be as bright as usual. Make sure your instrument panel brightness
control is in the full bright position. See Instrument Panel Brightness on page
Fog Lamps
If your vehicle has fog lamps, you can use them for better vision in foggy or misty conditions. Your parking lamps and/or
The fog lamp button is located near the exterior lamps control.
Press the button to turn the fog lamps on while the headlamps or parking lamps are on. Press the button again to turn them off. An indicator light will glow in the button when the fog lamps are on.
Remember, fog lamps alone will not give off as much light as your headlamps. Never use your fog lamps in the dark without turning on the headlamps.
The fog lamps will go off whenever your
Exterior Cargo Lamps
You can use the cargo lamps if you need more light in the cargo area of your vehicle or in the
Press this button, located on the driver side of the instrument panel near the exterior lamp control to turn the cargo lamps on and off. You must have your dome lamps on for your cargo lamps to come on. See
Dome Lamp on page
Interior Lamps
The thumbwheel for the interior lamps is located next to the exterior lamps control. See Exterior Lamps on
page
Instrument Panel Brightness
D(Instrument Panel Lights): Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. This will only work if
the headlamps or parking lamps are on. See Exterior Lamps on page
Dome Lamp
The dome lamp will come on when you open a door and will slowly dim to off when all doors are closed.
You can also turn the dome lamp on manually by turning the interior lamps thumbwheel all the way up. In this position, the dome lamp will remain on whether a door is opened or closed. See Interior Lamps on page
Dome Lamp Override
E(Dome Override): Press this button, located below the exterior lamp control, to turn the dome lamp off even when a door is opened. See Exterior Lamps on page
To return the lamp to automatic operation, press the button again.
Exit Lighting
With exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in.
Battery
This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK. This will keep your battery from running down.
Accessory Power Outlets
Your vehicle may have accessory power outlets.
With accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio.
Your vehicle may have two accessory power outlets located on the lower part of the instrument panel below the climate control system and there may be one located on the rear of the center console. A small cap must be pulled down to access an accessory power outlet. When not using an outlet be sure to cover it with the protective cap.
Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating.
Certain electrical accessories may not be compatible with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on accessory power outlets.
Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment.
Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
Your vehicle may have an ashtray and cigarette lighter.
Your ashtray is located at the front of your center console area. The ashtray can be removed for cleaning. When the ashtray is removed, this area can also be used as a cupholder.
Notice: If you put papers or other ???ammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ???ammable items in the ashtray.
To use the lighter, press it in all the way, and let go. When it???s ready, it will pop back out by itself.
Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not
use anything other than the cigarette lighter in the heating element.
Climate Controls
Climate Control System
Uplevel Climate Controls shown, Base similar
With this system you can control the heating, cooling, and ventilation for your vehicle.
Temperature Knob
The left knob on the control panel is used to adjust the temperature of the air in the vehicle. Turn the knob clockwise or counterclockwise to increase or decrease the temperature.
Fan Knob
9(Fan): The center knob on the control panel is used to control the fan speed. Turn the knob clockwise or counterclockwise to increase or decrease the fan speed.
If the knob is set on ???0??? (zero), some outside air will still enter the vehicle and will be directed according to
the position of the mode knob.
Mode Knob
The right knob on the control panel is used to direct the air???ow inside your vehicle. Turn the knob to select
one of the following modes:
H(Vent): Select this mode to direct air to the instrument panel outlets.
and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ???oor outlets.
[(Floor): Select this mode to direct air to the ???oor outlets. Enabling recirculation in heat mode may
cause interior window fogging under some conditions. If this occurs, see ???Defogging and Defrosting??? following.
Mode Buttons
@(Recirculation): If your vehicle has air conditioning, you will have the recirculation feature. This mode recirculates air inside the cabin, and prevents outside air from coming in the vehicle. It can be used to prevent outside odors from entering your vehicle and cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. An indicator light on the button will come on to let you know the recirculation mode is activated.
Recirculation is available in the
???oor (heat) modes. It should only be used while in
the light will not come on, while in ???oor/defog or defrost modes.
#(Air Conditioning): Your vehicle may have air conditioning. Press this button to turn the
The air conditioning will not function if the fan is turned off.
You may notice a slight change in engine performance when the air conditioning compressor shuts off and turns on again. This is normal.
The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature.
The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling
or after turning off the engine. This is normal.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield and side windows. Use the defog mode to clear the windows of fog
or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield
more quickly. For best results, clear all snow and ice from the windshield before defrosting.
Turn the mode knob on the climate control panel clockwise to select the defog or defrost modes.
/(Floor/Defog): This mode directs the air to the windshield, the side window outlets, and to the
???oor outlets. When you select this mode, the system runs the air conditioning compressor unless the outside temperature is near freezing or below. Recirculation
is not available in this mode.
0(Defrost): This mode directs most of the air to the windshield, and the side window outlets. When you select this mode, the system runs the air conditioning compressor unless the outside temperature is near,
or below freezing. Recirculation is not available in this mode.
Do not drive the vehicle until all the windows are clear.
Outlet Adjustment
Use the thumbwheel on the outlets to change the direction of the air ???ow.
Lift up or push down on the thumbwheel located in the center of the outlet to direct the air up or down, or slide the thumbwheel to the left or right to direct the air???ow from
Operation Tips
???Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ???ow of air into your vehicle.
???Use of
???Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively.
Warning Lights, Gages, and
Indicators
This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them.
Warning lights and gages can signal that something is wrong before it becomes serious enough to cause
an expensive repair or replacement. Paying attention to your warning lights and gages could also save you
or others from injury.
Warning lights come on when there may be or is a problem with one of your vehicle???s functions. As you will see in the details on the next few pages, some warning lights come on brie???y when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens.
Gages can indicate when there may be or is a problem with one of your vehicle???s functions. Often gages
and warning lights work together to let you know when there is a problem with your vehicle.
When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual???s advice. Waiting to do repairs can be costly ??? and even dangerous. So please get to know your warning lights and gages. They are a big help.
Your vehicle may also have a DIC that works along with the warning lights and gages. See Driver Information Center (DIC) on page
Instrument Panel Cluster
Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
United States automatic transmission version shown, Canada similar
Speedometer and Odometer
Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h).
Your odometer shows how far your vehicle has
been driven, in either miles (used in the United States) or kilometers (used in Canada).
The odometer mileage can be checked without the vehicle running. Simply press the trip information stem. See ???Odometer??? under DIC Controls and Displays
on page
You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must
be. But if it cannot, then it is set at zero, and a label must be put on the driver???s door to show the old mileage reading when the new odometer was installed.
Trip Odometer
Your vehicle has a trip odometer that can tell you how far your vehicle has been driven since you last set the trip odometer to zero.
See ???Trip Odometer??? under DIC Controls and Displays on page
Tachometer
The tachometer displays the engine speed in revolutions per minute (rpm).
Notice: If you operate the engine with the tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area.
Safety Belt Reminder Light
When the key is turned to ON or START, a chime will be provided for several seconds to remind people
to buckle their safety belts. The driver safety belt light will also be provided and stay on for several seconds, then it will ???ash for several more. You should buckle your seat belt.
This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion.
If the driver???s belt is buckled, neither the chime nor the light will be provided.
Airbag Readiness Light
There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag???s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag systems, see Airbag System on page
This light will come on when you start your vehicle, and it will ???ash for a few seconds. Then the light should go out. This means the system is ready.
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your
airbag system may not work properly. Have your vehicle serviced right away.
{CAUTION:
If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not in???ate in a crash, or they could even in???ate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle.
The airbag readiness light should ???ash for a few seconds when you turn the ignition key to ON. If the light does not come on then, have it ???xed so it will be ready to warn you if there is a problem.
Airbag Off Light
Regular Cab Models and Extended Cab Models without Rear Seats
When you turn the airbag off switch to the off position, the off indictor will come on and stay on to remind you that the airbag has been turned off. When you turn the airbag off switch to the on position, the on indicator will come on. See Airbag Off Switch on page
United States
Canada
{CAUTION:
If the right front passenger???s frontal airbag is turned off for a person who is not in a risk group identi???ed by the national government, that person will not have the extra protection of an airbag. In a crash, the frontal airbag would not be able to in???ate and help protect the person sitting there.
Do not turn off the right front passenger???s frontal airbag unless the person sitting there is in a risk group identi???ed by the national government. See Airbag Off Switch on
page
{CAUTION:
If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger???s frontal airbag could in???ate even though the switch is off. If this ever happens, do not let anyone whom the national government has identi???ed as a member of a passenger airbag risk group sit in the right front passenger???s position (for example, do not secure a
Battery Warning Light
This light will come on brie???y when you start the vehicle, as a check to show you it is working; then it should go out.
If it stays on, or comes on while you are driving, you may have a problem with the electrical charging system. Have it checked right away. Driving while this light is
on could drain your battery and result in a vehicle that may stall. See DIC Warnings and Messages on
page
If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and climate control system.
Transmission)
This light appears when you need to shift to the next higher gear on
a manual transmission vehicle.
Brake System Warning Light
Your vehicle???s hydraulic brake system is divided into two parts. If one part is not working, the other part can
still work and stop you. For good braking, though, you need both parts working well.
If the warning light comes on, there could be a brake problem. Have your brake system inspected right away.
Shifting when the indicator light is on will help you get the best fuel economy. See
Manual Transmission Operation on page
This light should come on brie???y when you turn the ignition key to ON. If it does not come on then, have it ???xed so it will be ready to warn you if there is a problem.
When the ignition is on, the brake system warning light will also come on when you set your parking brake. See Parking Brake on page
If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push, or the pedal may go closer to the
???oor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page
{CAUTION:
Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service.
Light
With the
start your engine to show it is working. Then it will
turn off. This is normal.
If the light stays on, or comes on when you???re driving, your vehicle needs service. If the regular brake system warning light isn???t on, you still have brakes, but you don???t have
brakes. See Brake System Warning Light on page
The
the light doesn???t come on then, have it ???xed so it will be ready to warn you if there is a problem.
Engine Coolant Temperature Gage
This gage shows the engine coolant temperature.
If the gage pointer is near the top of the gage, the engine is too hot. It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as
soon as possible.
See Engine Overheating on page
Malfunction Indicator Lamp
Check Engine Light
Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems.
This system is called OBD II
Notice: If you keep driving your vehicle with this light on, after awhile, your emission controls
may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty.
Notice: Modi???cations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle???s emission controls and may cause this light to come on. Modi???cations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test.
This light should come on, as a check to show you it is working, when the ignition is on and the engine is
not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways:
???Light Flashing ??? A mis???re condition has been detected. A mis???re increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required.
???Light On Steady ??? An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required.
If the Light is Flashing
The following may prevent more serious damage to your vehicle:
???Reducing vehicle speed
???Avoiding hard accelerations
???Avoiding steep uphill grades
???If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible
If the light stops ???ashing and remains on steady, see ???If the Light Is On Steady??? following.
If the light continues to ???ash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see ???If
the Light Is On Steady??? following. If the light is still ???ashing, follow the previous steps, and see your dealer for service as soon as possible.
If the Light Is On Steady
You may be able to correct the emission system malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page
Did you just drive through a deep puddle of water?
If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off.
Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel. See
Gasoline Octane on page
light to turn on.
If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off.
If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has
the proper test equipment and diagnostic tools to ???x any mechanical or electrical problems that may have developed.
Emissions Inspection and Maintenance
Programs
Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
Here are some things you need to know to help your vehicle pass an inspection:
Your vehicle will not pass this inspection if the check engine light is on or not working properly.
Your vehicle will not pass this inspection if the OBD
of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection.
Oil Pressure Light
{CAUTION:
Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ???re. You or others could be burned.
Check your oil as soon as possible and have your vehicle serviced.
Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil.
This light tells you if there could be a problem with your engine oil pressure.
The light goes on when you turn your key to ON or START. It goes off once you start your engine. That???s a check to be sure the light works. If it doesn???t come
on, be sure to have it ???xed so it will be there to warn you if something goes wrong.
When the light comes on and stays on, it means that oil isn???t ???owing through your engine properly. You could
be low on oil and you might have some other system problem. See Engine Oil on page
DIC Warnings and Messages on page
This light will come on brie???y when you turn the key to START. The
light will stay on until the engine starts.
If the ignition is turned on, and the light ???ashes, the Passlock?? system has entered a tamper mode. If
the vehicle fails to start, see Passlock?? on page
If the light comes on continuously while driving and stays on, there may be a problem with the Passlock?? system. Your vehicle will not be protected by Passlock??, and you should see your dealer.
Also, see Content
This light comes on whenever you set your cruise control.
The light will go out when the cruise control is turned off. See Cruise Control on page
Highbeam On Light
This light comes on whenever the
See Headlamp
Daytime Running Lamps (DRL)
Indicator Light
This light turns on whenever the Daytime Running Lamps are on.
See Daytime Running Lamps (DRL) on page
Fuel Gage
When the ignition is on, the fuel gage tells you about how much fuel you have remaining in the fuel tank.
Here are four things that some owners ask about. None of these indicate a problem with your fuel gage:
???At the gas station, the gas pump shuts off before the gage reads full.
???It takes a little more or less fuel to ???ll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank???s capacity to
???ll the tank.
???The gage moves a little when you turn a corner or speed up.
???The gage does not go back to empty when you turn off the ignition.
When the fuel in the fuel tank is low, you will see a LOW FUEL message on the Driver Information
Center (DIC) display. See DIC Warnings and Messages on page
Driver Information Center (DIC)
The DIC display is located on the instrument panel cluster. The DIC can display information such as the trip odometer and personalization features.
DIC Controls and Displays
The Driver Information Center (DIC) comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off.
If a problem is detected, a warning message will appear on the display. Pressing and releasing the trip odometer reset stem on the DIC will acknowledge some current warnings or service messages. Some messages will only clear once the required action has been taken.
The DIC has different modes which can be accessed by pressing the trip odometer reset stem on the DIC. These modes are explained following. The DIC trip odometer reset stem is located on the instrument panel cluster next to the DIC display. To scroll through the available functions, press and release the reset stem.
Trip Information
Odometer
The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows
the total distance the vehicle has been driven in either miles or kilometers.
Trip Odometer
Press and release the reset stem until TRIP appears on the DIC display. This shows the current distance traveled since the last reset of the trip odometer in either miles or kilometers.
Press and hold the reset stem for approximately four seconds to reset the trip odometer.
Engine Oil Life System
Press the reset stem until OIL LIFE RESET appears (alternating between OIL LIFE and RESET) on the DIC display. The engine oil life system calculates an estimate of the oil???s remaining useful life. The CHANGE OIL message will alert you to change your oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page
In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in
the Maintenance Schedule in this manual. See Engine Oil on page
Automatic Door Locks
This feature allows you to program your door locks to a preferred setting.
To set your choice for this feature, perform the following steps:
1.With the engine off, turn the key to LOCK.
2.Press and hold the power door lock button for approximately three seconds until the DIC display shows the current door lock mode.
3.To view the next available mode, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold again to view each mode.
4.Once the desired mode is shown on the DIC display, brie???y press the reset stem to set your choice. The DIC display will then clear.
The following are the available modes:
Lock 1 (default): On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of PARK (P) and unlocks all of the doors when the vehicle is shifted into PARK (P).
On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater
than 15 mph (24 km/h) and unlocks all of the doors when the key is removed from the ignition.
Lock 2: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle
is shifted out of PARK (P) and unlocks the driver???s door when the vehicle is shifted into PARK (P).
On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h) and unlocks the driver???s door when the key is removed from the ignition.
Lock 3: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle
is shifted out of PARK (P). The doors will not automatically unlock.
On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h). The doors will not automatically unlock.
Remote Keyless Entry Feedback
This feature allows you to program your remote keyless entry feedback to a preferred setting.
To set your choice for this feature, perform the following steps:
1.With the engine off, turn the key to LOCK.
2.Press and hold the lock and unlock buttons on the remote keyless entry transmitter at the same time. Hold both buttons until the DIC display shows
the current remote keyless entry feedback mode.
3.To view the next available mode, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold again to view each mode.
4.Once the desired mode is shown on the DIC display, brie???y press the reset stem to set your choice. The DIC display will then clear.
The following are the available modes:
RFA 1 (default): This mode ???ashes the parking lamps when you press the lock or unlock buttons on the remote keyless entry transmitter.
RFA 2: This mode ???ashes the parking lamps and sounds the horn when you press the lock button on the remote keyless entry transmitter. This mode also ???ashes the parking lamps when you press the unlock button on the remote keyless entry transmitter.
RFA 3: This mode ???ashes the parking lamps and sounds the horn when you press the lock or unlock buttons on the remote keyless entry transmitter.
RFA 4: This mode disables remote keyless entry feedback. There will be no feedback when you press the lock or unlock buttons on the remote keyless entry transmitter.
Language
This feature allows you to choose the language in which the DIC display will show information.
To set your choice for this feature, perform the following steps:
1.With the engine off, turn the key to ON.
2.Press and release the reset stem until the language is shown on the DIC display.
3.To view the next available language, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold
again to view each language. You can choose from English (default), Spanish (United States only) or French (Canada only).
4.Once the desired language is shown on the DIC display, brie???y press the reset stem to set your choice.
DIC Warnings and Messages
Warning messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. More than one message may appear at one time. They will appear one after the other. The messages are displayed for three seconds each. Some messages may not require immediate action
but you should press and release the trip odometer reset stem to acknowledge that you received the message and clear it from the display. Each message must
be acknowledged individually. Some messages cannot be cleared from the display because they are more urgent. These messages require action before they can be removed from the DIC display. The following are the possible messages that can be displayed and some information about them.
AC (Air Conditioning) OFF
This message will be displayed when the engine coolant temperature is too high and the air conditioning in
your vehicle needs to be turned off. See Engine Overheating on page
ABS
This message will be displayed if there is a problem with your antilock brake system. Check your antilock brake system as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page
page
it from the DIC display.
BATTERY
This message will be displayed when there is a problem with your vehicle???s battery. See Battery on page
BRAKES
This message will be displayed if there is a problem with your brakes. Check your brakes as soon as possible and have your vehicle serviced by your
GM dealer. See Brakes on page
Press and release the reset stem to acknowledge the message and clear it from the DIC display.
CHANGE OIL
This message will be displayed when the oil needs to be changed. Check the oil in your vehicle as soon as possible and have your vehicle serviced by your
GM dealer. See Engine Oil on page
DOORS
This message will be displayed on your DIC when one or more of your doors is ajar. You should check all
the doors on your vehicle to make sure they are closed. The message will clear from the display after all of
the doors are closed.
ENG (Engine) HOT
This message will be displayed when your engine coolant temperature is hot. Check your engine coolant temperature gage. See Engine Coolant Temperature Gage on page
Engine Overheating on page
FLUID
This message will be displayed if your brake ???uid is low. Check the brake ???uid as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page
DIC display.
FUEL CAP
This message will be displayed if your vehicle???s fuel cap is either off or loose. You should pull over and check to see if your vehicle???s fuel cap is secure as soon as possible. You may also see the check engine light on the instrument panel cluster. See Malfunction Indicator Lamp on page
stem to acknowledge the message and clear it from the display.
LOW FUEL
This message will be displayed if the level of fuel in your vehicle is low. You should also check your fuel gage. See Fuel Gage on page
LOW TRAC (Traction)
If you have the Traction Control System (TCS), you will see this message when a low traction condition is detected. See Traction Control System (TCS) on
page
it from the DIC display.
OIL
This message will be displayed when your oil pressure is low. See Oil Pressure Light on page
OIL LIFE
This message will be displayed when you need to check your engine oil life system. Press the reset stem to acknowledge the message. For more information, see ???Engine Oil Life System??? under DIC Controls and Displays on page
PARK BRK (Brake)
This message will be displayed when your vehicle???s parking brake is active. See Parking Brake on page
more information. The message will clear from the display after the parking brake is released.
REDUCED POWER
This message will be displayed when your vehicle???s engine power is reduced. Press the reset stem to acknowledge the message and clear it from the display.
SERV (Service) 4WD
This message will be displayed when there is a problem with your transfer case control system. Check the transfer case on your vehicle and have it serviced by your GM dealer. See
it from the display.
TRACTION FAULT
If you have the Traction Control System (TCS), you may see this message if there is a problem with your Traction Control System (TCS). Check your TCS as soon as possible and have your vehicle serviced by your
GM dealer. See Traction Control System (TCS) on page
SERV VEH (Service Vehicle)
This message will be displayed if your vehicle needs service. You should have your vehicle serviced by your GM dealer as soon as possible.
TURN SIGNAL
This message will be displayed when your turn signal is on for approximately 0.75 miles (1.2 km) of travel. Press the reset stem to acknowledge the message and clear it from the display.
Audio System(s)
Notice: Before adding any sound equipment to your vehicle, like a tape player, CB radio, mobile telephone, or
sound equipment may interfere with the operation of your vehicle???s engine, radio, or other systems, and even damage them. Your vehicle???s systems may interfere with the operation of sound equipment
that has been added improperly.
Figure out which audio system is in your vehicle, ???nd out what your audio system can do, and how to operate all of its controls.
Setting the Time for Radios without Radio Data Systems (RDS)
Press and hold HR until the correct hour appears on the display. Press and hold MIN until the correct minute appears on the display. There is an initial
Display the time with the ignition off, by pressing RCL, HR, or MIN.
Setting the Time for Radios with Radio Data Systems (RDS)
The radio may have a button marked with an H or HR to represent hours and an M or MN to represent minutes.
Press and hold the hour button until the correct hour appears on the display. Press and hold the minute button until the correct minute appears on the display. The time can be set with the ignition on or off.
To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold the hour and minute buttons at the same time until RDS TIME appears on the display. To accept this time, press and hold the hour and minute buttons, at the same time, for another two seconds. If the time is not available from the station, NO UPDAT will appear on the display.
RDS time is broadcast once a minute. After tuning to an RDS broadcast station, it may take a few minutes for the time to update.
Playing the Radio
PWR (Power): Press this knob to turn the system on and off.
VOL (Volume): Turn this knob to increase or to decrease the volume.
RCL (Recall): Press this knob to switch the display between the radio station frequency and the time. When the ignition is off, press this knob to display the time.
Finding a Station
AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection.
TUNE: Turn this knob to select radio stations.
oSEEK p: Press the right or the left arrow to go to the next or to the previous station and stay there.
To scan stations, press and hold either SEEK arrow for two seconds until you hear a beep. The radio will go to a station, play for a few seconds, then go on to the next station. Press either SEEK arrow again to stop scanning.
To scan preset stations, press and hold either SEEK arrow for more than four seconds until you hear two beeps. The radio will go to the ???rst preset station stored on the pushbuttons, play for a few seconds, then go on to the next preset station. Press either SEEK arrow again to stop scanning presets.
The radio will only seek and scan stations with a strong signal that are in the selected band.
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons, by performing the following steps:
1.Turn the radio on.
2.Press AM FM to select FM1, FM2, or AM.
3.Tune in the desired station.
4.Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station
that was set will return.
5.Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
AUDIO: To adjust bass and treble, press and release AUDIO until BAS or TRE appears on the display. Then press and hold the up or the down arrow to increase or to decrease. If a station is weak or noisy, decrease the treble.
To adjust bass or treble to the middle position, select BAS or TRE. Then press and hold AUDIO for more than two seconds until you hear a beep. B and a zero or T and a zero will appear on the display.
To adjust both tone controls and both speaker controls to the middle position, ???rst end out of audio mode
by pressing another button, causing the radio to perform that function or by waiting ???ve seconds for the display
to return to time of day. Then press and hold AUDIO for more than two seconds until you hear a beep. CEN
will appear on the display.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and the left speakers, press and release AUDIO until
BAL appears on the display. Then press and hold the up or the down arrow to move the sound toward the right or the left speakers.
To adjust the fade between the front and the rear speakers, press and release AUDIO until FAD appears on the display. Then press and hold the up or the down arrow to move the sound toward the front or the rear speakers.
To adjust balance or fade to the middle position, select BAL or FAD. Then press and hold AUDIO for more than two seconds until you hear a beep. L (balance) and a zero or F and a zero will appear on the display.
To adjust both tone controls and both speaker controls to the middle position, ???rst end out of audio mode
by pressing another button, causing the radio to perform that function or by waiting ???ve seconds for the display
to return to time of day. Then press and hold AUDIO for more than two seconds until you hear a beep. CEN
will appear on the display.
Fade may not be available if the vehicle is a regular cab model.
Radio Messages
CAL (Calibrated): The audio system has been calibrated for your vehicle from the factory. If CAL appears on the display it means that the radio has not been con???gured properly for your vehicle and must
be returned to your GM dealer for service.
LOC (Locked): This message is displayed when the THEFTLOCK?? system has locked up. Take the vehicle to your GM dealer for service.
If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer.
Radio with CD
Radio Data System (RDS)
The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
With RDS, the radio can do the following:
???Seek to stations broadcasting the selected type of programming
???Receive announcements concerning local and national emergencies
???Display messages from radio stations
???Seek to stations with traffic announcements
This system relies upon receiving speci???c information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
While the radio is tuned to an RDS station, the station name or call letters will appear on the display instead of the frequency. RDS stations may also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast.
XM??? Satellite Radio Service
XM??? is a satellite radio service that is based in the 48 contiguous United States. XM??? offers 100 coast to
coast channels including music, news, sports, talk, and children???s programming. XM??? provides digital quality audio and text information that includes song title and artist name. A service fee is required in order to receive the XM??? service. For more information, contact XM??? at www.xmradio.com or call
Playing the Radio
PWR (Power): Press this knob to turn the system on and off.
oVOL p(Volume): Turn this knob to increase or to decrease the volume.
DISPL (Display): Press this knob to switch the display between the radio station frequency and the time. When the ignition is turned off, press this knob to display the time.
For RDS, press the DISPL knob to change what appears on the display while using RDS. The display options are station name, RDS station frequency, PTY, and the name of the program (if available).
For XM??? (if equipped), press the DISPL knob while in XM??? mode to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/Channel Name.
To change the default on the display, press the DISPL knob until you see the display you want, then hold this knob for two seconds. The radio will produce one beep and the selected display will now be the default.
AUTO VOL (Automatic Volume): With automatic volume, the audio system adjusts automatically to make up for road and wind noise as you drive.
Set the volume at the desired level. Press this button to select LOW, MEDIUM, or HIGH. AVOL will appear
on the display. Each higher setting will allow for more volume compensation at faster vehicle speeds. Then as you drive, automatic volume increases the volume,
as necessary, to overcome noise at any speed.
The volume level should always sound the same to you as you drive. NONE will appear on the display if the radio cannot determine the vehicle speed. To turn automatic volume off, press this button until OFF appears on the display.
Finding a Station
BAND: Press this button to switch between FM1, FM2, AM, or XM1 or XM2 (if equipped). The display will show the selection.
oTUNE p: Turn this knob to select radio stations.
oSEEK p: Press the right or the left arrow to
go to the next or to the previous station and stay there.
The radio will only seek stations with a strong signal that are in the selected band.
oSCAN p: Press and hold either arrow for more than two seconds. SCAN will appear on the display and the radio will produce one beep. The radio will go to
a station, play for a few seconds, then go on to the next station. Press either arrow again or one of the pushbuttons to stop scanning presets.
To scan preset stations, press and hold either arrow for more than four seconds. PSCN will appear on the display and the radio will produce one beep. The radio will go to a preset station, play for a few seconds, then go on to the next preset station. Press either arrow again or one of the pushbuttons to stop scanning presets.
The radio will only scan stations with a strong signal that are in the selected band.
Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps:
1.Turn the radio on.
2.Press BAND to select FM1, FM2, AM, or XM1 or XM2.
3.Tune in the desired station.
4.Press AUTO EQ to select the equalization.
5.Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station
that was set will return and the equalization that was selected will be stored for that pushbutton.
6.Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
AUDIO: Push and release the AUDIO knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, decrease the treble.
To adjust the bass and the treble to the middle position, push and hold the AUDIO knob. The radio will produce one beep.
To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control is displayed. ALL CENTERED will appear on the display and you will hear a beep.
AUTO EQ (Automatic Equalization): Press this button to select customized equalization settings designed
for country/western, jazz, talk, pop, rock, and classical.
To return the bass and treble to the manual mode, push and release the AUDIO knob until CUSTOM appears on the display.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO
knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers.
To adjust the fade between the front and the rear speakers, push and release the AUDIO knob until FADE appears on the display. Turn the knob to move the sound toward the front or the rear speakers.
To adjust the balance and the fade to the middle position, push the AUDIO knob, then push it again and hold it until you hear one beep.
To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control is displayed. ALL CENTERED will appear on the display and you will hear a beep.
Finding a Program Type (PTY) Station
(RDS and XM???)
To select and ???nd a desired PTY perform the following:
1.Press the SEEK TYPE button to activate program type select mode. TYPE and a PTY will appear on the display.
2.Turn the
3.Once the desired PTY is displayed, press the SEEK TYPE button to select and to take you to the PTY???s ???rst station.
4.To go to another station within that PTY and the PTY is displayed, press the SEEK TYPE button once. If the PTY is not displayed, press the SEEK TYPE button twice to display the PTY and then to go to another station.
5.Press
If PTY times out and is no longer on the display, go back to Step 1.
If both PTY and TRAF are on, the radio will search for stations with the selected PTY and traffic announcements.
If the radio cannot ???nd the desired program type, NONE will appear on the display and the radio will return to the last station you were listening to.
BAND (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same program type. To turn alternate frequency on, press and hold BAND for two seconds. AF ON will appear on the display. The radio may switch to stations with a stronger frequency.
To turn alternate frequency off, press and hold BAND again for two seconds. AF OFF will appear on the display. The radio will not switch to other stations.
This function does not apply for XM??? Satellite Radio Service.
RDS Messages
ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is low or
a CD is playing. If a CD is playing, play will stop during the announcement. Alert announcements cannot be turned off.
ALERT! will not be affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.
INFO (Information): If the current station has a message, the information symbol will appear on the display. Press this button to see the message. The message may display the artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the message will appear every three seconds. To scroll through the message, press and release the INFO button. A new group of words will appear on the display after every press of this button. Once the complete message has been displayed, the information symbol will disappear from the display until another new message is received.
The last message can be displayed by pressing the INFO button. You can view the last message until a new message is received or a different station is tuned to.
When a message is not available from a station, NO INFO will appear on the display.
TRAF (Traffic): If TRAF appears on the display, the tuned station broadcasts traffic announcements
and when a traffic announcement comes on the tuned radio station you will hear it.
If the station does not broadcast traffic announcements, press the TRAF button and the radio will seek to a station that does. When a station that broadcasts traffic announcements is found, the radio will stop seeking and TRAF will appear on the display. If no station
is found that broadcasts traffic announcements, NO TRAF will appear on the display.
If TRAF is on the display, press the TRAF button to turn off the traffic announcements.
The radio will play the traffic announcement if the volume is low. The radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements.
This function does not apply to XM??? Satellite Radio Service.
Radio Messages
CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If
CAL ERR appears on the display it means that the radio has not been con???gured properly for your vehicle and
it must be returned to your GM dealer for service.
LOCKED: This message is displayed when the THEFTLOCK?? system has locked up. Take your vehicle to your GM dealer for service.
If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer.
XM??? Radio Messages
XM??? Radio Messages (cont???d)
Playing a CD
Insert a CD partway into the slot, label side up. The player will pull it in, and READING will appear on
the display. The CD should begin playing. If you want to insert a CD with the ignition off, ???rst press the EJT button or the DISPL knob.
If the ignition or radio is turned off with a CD in the player, it will stay in the player. When the ignition
or radio is turned on, the CD will start to play where it stopped, if it was the last selected audio source.
When the CD is inserted, the CD symbol will appear on the display. As each new track starts to play, the
track number will appear on the display.
The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
If playing a
in skipping, difficulty in ???nding tracks, and/or difficulty in loading and ejecting. If these problems occur try a known good CD.
Do not add paper labels to CDs, they could get caught in the CD player.
If an error appears on the display, see ???CD Messages??? later in this section.
1 FLDx(Previous): This button is inactive when playing a
2 FLDw(Next): This button is inactive when playing a
3 REV (Reverse): Press and hold this pushbutton to reverse quickly within a track. Press and hold this pushbutton for less than two seconds to reverse at 10 times the normal playing speed. Press and hold it for more than two seconds to reverse at 20 times the normal playing speed. Release this pushbutton to
play the passage. ET and the elapsed time of the track will appear on the display.
4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at
six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed. Release this pushbutton to play the passage. ET and the elapsed time of the track
will appear on the display.
6 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order. RDM ON will appear on the display. RDM and the track number will appear on the display when each track starts to play. Press RDM again to turn off random play. RDM OFF will appear on the display.
oSEEK p: Press the left arrow to go to the start of the current or the previous track. Press the right arrow to go to the start of the next track. Pressing either arrow for more than two seconds will scan the previous or next tracks at ???ve to eight seconds per track. SCAN and the track number will appear on the display. Release the button to stop searching and to play the track.
oTUNE p: Turning the TUNE knob will fast track reverse or advance through tracks. The track number will appear on the display for each track.
DISPL (Display): Press this knob to see how long the current track has been playing. ET and the elapsed time of the track will appear on the display. To change the default on the display, track or elapsed time, press this knob until you see the display you want, then hold the knob for two seconds. The radio will produce one beep and the selected display will now be the default.
BAND: Press this button to listen to the radio when a CD is playing. The inactive CD will remain safely inside the radio for future listening.
CD AUX (Auxiliary): Press this button to play a CD when listening to the radio. The CD symbol will appear on the display when a CD is loaded.
ZEJT (Eject): Press this button to eject a CD. Eject may be activated with either the ignition or radio off. CDs may be loaded with the ignition and radio off if this button is pressed ???rst.
Using an MP3 CD
MP3 Format
This MP3 player will accept MP3 ???les that were recorded on an up to 700 MB
40 kpbs, 56 kpbs, 64 kpbs, 80 kpbs, 96 kpbs, 112 kpbs, 128 kpbs, 160 kpbs, 192 kpbs, 224 kpbs, 256 kpbs, and 320 kpbs or a variable bit rate. Song title,
artist name, and album will be available when recorded using ID3 tags versions 1 and 2.
The player will be able to read and play a maximum of 50 folders, 50 playlists, 10 sessions, and 255 ???les. Long ???le, folder, or playlist names or a combination of a large number of ???les and folders or playlists may
cause the player to be unable to play up to the maximum number of ???les, folders, playlists, or sessions. If you wish to play large numbers of ???les, folders, playlists or sessions minimize the length of the ???le, folder or playlist name. You can also play an MP3 CD that was recorded using no ???le folders. The system can support up to 11 folders in depth, though, keep the depth of the folders to a minimum in order to keep down the complexity and confusion in trying to locate a particular folder during playback. If a CD contains more than the maximum of 50 folders, 50 playlists,
10 sessions, and 255 ???les the player will let you access and navigate up to the maximum, but all items over the maximum will be ignored.
Root Directory
The root directory will be treated as a folder. If the root directory has compressed audio ???les, the directory
will be displayed as F1 ROOT. All ???les contained directly under the root directory will be accessed prior to any root directory folders. However, playlists (Px) will always be accessed before root folders or ???les.
Empty Directory or Folder
If a root directory or a folder exists somewhere in the ???le structure that contains only folders/subfolders and no compressed ???les directly beneath them, the player will advance to the next folder in the ???le structure that contains compressed audio ???les and the empty folder will not be displayed or numbered.
No Folder
When the CD contains only compressed ???les, the ???les will be located under the root folder. The next and previous folder functions will have no function on a CD that was recorded without folders or playlists. When displaying the name of the folder the radio will display ROOT.
When the CD contains only playlists and compressed audio ???les, but no folders, all ???les will be located under the root folder. The folder down and the folder up buttons will search playlists (Px) ???rst and then go to the root folder. When the radio displays the name of the folder the radio will display ROOT.
Order of Play
Tracks will be played in the following order:
???Play will begin from the ???rst track in the ???rst playlist and will continue sequentially through all tracks in each playlist. When the last track of the last playlist has been played, play will continue from the ???rst track of the ???rst playlist.
???If the CD does not contain any playlists, then play will begin from the ???rst track under the root directory. When all tracks from the root directory have been played, play will continue from ???les according to their numerical listing. After playing the last track from the last folder, play will begin again at the ???rst track of the ???rst folder or root directory.
When play enters a new folder, the display will not automatically show the new folder name unless
you have chosen the folder mode as the default display. See DISPL later in this section for more information. The new track name will appear on the display.
File System and Naming
The song name that will be displayed will be the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio will display the ???le name without the extension (such as .mp3) as the track name.
Track names longer than 32 characters or four pages will be shortened. The display will not show parts
of words on the last page of text and the extension of the ???lename will not be displayed.
Preprogrammed Playlists
You can access preprogrammed playlists which were created by WinAmp???, MusicMatch???, or Real Jukebox??? software, however, you will not have editing capability. These playlists will be treated as special folders containing compressed audio song ???les.
Playing an MP3
Insert a CD partway into the slot, label side up. The player will pull it in, and READING will appear on
the display. The CD should begin playing and the CD symbol will appear on the display. If you want to insert a CD with the ignition off, ???rst press the EJT button or
the DISPL knob.
If the ignition or radio is turned off with a CD in the player, it will stay in the player. When the ignition
or radio is turned on, the CD will start to play where it stopped, if it was the last selected audio source.
As each new track starts to play, the track number will appear on the display.
The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
If playing a
Do not add paper labels to CDs, they could get caught in the CD player.
If an error appears on the display, see ???CD Messages??? later in this section.
1 FLDx(Previous Folder): Press this pushbutton to go to the ???rst track in the previous folder. Pressing this button while in folder random mode will take you to
the previous folder and random the tracks in that folder.
2 FLDw(Next Folder): Press this pushbutton to go to the ???rst track in the next folder. Pressing this
button while in folder random mode will take you to the next folder and random the tracks in that folder.
3 REV (Reverse): Press and hold this pushbutton to reverse quickly within a track. Press and hold this pushbutton for less than two seconds to reverse at
10 times the normal playing speed. Press and hold it for more than two seconds to reverse at 20 times the normal playing speed. Release this pushbutton to play the passage. REV and the elapsed time of the track
will appear on the display.
4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at 10 times the normal playing speed. Press and hold it for more than two seconds to advance at 20 times the normal playing speed. Release this pushbutton to play the passage. FWD and the elapsed time of
the track will appear on the display.
6 RDM (Random): To random the tracks in the current folder or playlist, press and release this pushbutton. FLDR RDM will appear on the display. Once all of the tracks in the current folder or playlist have been
played the system will move on to the next folder or playlist and play all of the tracks in random order.
To random all the tracks on the CD, press and hold this pushbutton for two seconds. You will hear a beep
and DISC RDM will appear on the display. This feature will not work with playlists.
When in random, pressing and releasing either SEEK arrow will take you to the next or previous random track.
Press and release this pushbutton again to turn off random play. NO RDM will appear on the display.
oSEEK p: Press the left arrow to go to the start of the previous track. Press the right arrow to go to the start of the next track. Pressing either arrow for
more than two seconds will search the previous or next tracks at two tracks per second. Release the button
to stop searching and to play the track.
oTUNE p: Turning the TUNE knob will fast track reverse or advance through the tracks in all folders
or playlists. The track number and ???le name will appear on the display for each track. Turning this knob while
in random will fast track reverse or advance the tracks in sequential order.
DISPL (Display): Press this knob to switch between track mode, folder/playlist mode, and time of day mode. The display will show only eight characters, but there can be up to four pages of text. If there are more
than eight characters in the song, folder, or playlist name, pressing this knob within two seconds will take you to the next page of text. If there are no other pages to be shown, pressing this knob within two seconds
will take you to the next display mode.
???Track mode will display the current track number and the ID3 tag song name.
???Folder/playlist mode will display the current folder or playlist number and the folder/playlist name.
???Time of day mode will display the time of day and the ID3 tag song name.
To change the default on the display, press the DISPL knob until you see the display you want, then hold this knob for two seconds. The radio will produce one beep and the selected display will now be the default.
INFO (Information): INFO will appear on the display whenever a current track has ID3 tag information. Press this button to display the artist name and album contained in the tag. INFO will disappear from the display when the information in the ID3 tag has ???nished.
BAND: Press this button to listen to the radio when a CD is playing. The inactive CD will remain safely inside the radio for future listening.
CD AUX (Auxiliary): Press this button to play a CD when listening to the radio. The CD symbol will appear on the display when a CD is loaded.
ZEJT (Eject): Press this button to eject a CD. Eject may be activated with either the ignition or radio off. CDs may be loaded with the ignition and radio off if this button is pressed ???rst.
CD Messages
CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons:
???It is very hot. When the temperature returns to normal, the CD should play.
???You are driving on a very rough road. When the road becomes smoother, the CD should play.
???The CD is dirty, scratched, wet, or upside down.
???The air is very humid. If so, wait about an hour and try again.
???The format of the CD may not be compatible. See ???MP3 Format??? earlier in this section.
???There may have been a problem while burning the CD.
???The label may be caught in the CD player.
If the CD is not playing correctly, for any other reason, try a known good CD.
If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer. If the radio displays an error message, write it down and provide it to
your GM dealer when reporting the problem.
Radio with
Playing the Radio
PWR (Power): Push this knob to turn the system on and off.
oVOLUME p: Turn this knob to increase or to decrease the volume.
INFO (Information): Press this knob to switch the display between the radio station frequency and the time. When the ignition is off, press this knob to display the time.
For RDS, press the INFO knob to change what appears on the display while using RDS. The display options are station name, RDS station frequency, PTY, and the name of the program (if available).
To change the default on the display, press the INFO knob until you see the display you want, then hold
the knob until you hear a beep. The selected display will now be the default.
AUTO VOL (Automatic Volume): With automatic volume, the audio system will adjust automatically to make up for road and wind noise as you drive by increasing the volume as vehicle speed increases.
Set the volume at the desired level. Press this button to select MID, MED, or MAX. AUTO VOL will appear on the display. Each higher setting will provide more volume compensation at faster vehicle speeds. To turn automatic volume off, press this button until AUTO VOL OFF appears on the display.
Finding a Station
BAND: Press this button to switch between FM1, FM2, or AM. The display will show the selection.
oTUNE p: Turn this knob to select radio stations.
??SEEK ??: Press either the SEEK or the TYPE arrows to go to the next or to the previous station and stay there.
The radio will only seek stations with a strong signal that are in the selected band.
??SCAN ??: Press and hold either the SCAN or the TYPE arrows for two seconds until SCN appears on the display and you hear a beep. The radio will go to a station, play for a few seconds, then go on to the next station. Press either the SCAN or the TYPE arrows again to stop scanning.
To scan preset stations, press and hold either the SCAN or the TYPE arrows for more than four seconds. PSC will appear on the display and you will hear a double beep.
The radio will go to a preset station, play for a few seconds, then go on to the next preset station. Press either the SCAN or the TYPE arrows again to stop scanning presets.
The radio will only scan stations with a strong signal that are in the selected band.
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered pushbuttons, by performing the following steps:
1.Turn the radio on.
2.Press BAND to select FM1, FM2, or AM.
3.Tune in the desired station.
4.Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station
that was set will return for that pushbutton.
5.Repeat the steps for each pushbutton.
To store an equalization setting to a preset station perform the following:
1.Tune to the preset station.
2.Press and release the AUTO EQ button to select the equalization setting.
Once the equalization no longer appears on the display, the equalization will be set for that preset station.
Setting the Tone (Bass/Treble)
AUDIO: Push and release the AUDIO knob until BASS, MID, or TREB appears on the display. Turn the knob
to increase or to decrease. The display will show
the bass, midrange, or treble level. If a station is weak or noisy, decrease the treble.
To adjust the bass, midrange, and treble to the middle position, push and hold the AUDIO knob. The radio
will produce one beep and adjust the display level to the middle position.
To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker controls are displayed. ALL CENTERED will appear on the display and you will hear a beep.
AUTO EQ (Automatic Equalization): Press this button to select customized equalization settings designed
for country/western, jazz, talk, pop, rock, and classical.
To return to the manual mode, press the AUTO EQ button until CUSTOM appears on the display. Then manually adjust the bass, midrange, and treble using the AUDIO knob.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO
knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers.
To adjust the fade between the front and rear speakers, push and release the AUDIO knob until FAD appears on the display. Turn the knob to move the sound toward the front or the rear speakers.
To adjust the balance and fade to the middle position, push and hold the AUDIO knob. The radio will produce one beep and adjust the display level to the middle position.
To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker controls are displayed. ALL CENTERED will appear on the display and you will hear a beep.
Radio Data System (RDS)
The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
With RDS, the radio can do the following:
???Seek to stations broadcasting the selected type of programming
???Receive announcements concerning local and national emergencies
???Display messages from radio stations
This system relies upon receiving speci???c information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
While the radio is tuned to an RDS station, the station name or call letters will appear on the display instead of the frequency. RDS stations may also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast.
Finding a Program Type (PTY) Station
To select and ???nd a desired PTY perform the following:
1.Press the TYPE button to activate program type select mode.
2.Turn the TYPE knob or press and release the TYPE button to select a PTY.
3.Once the desired PTY is displayed, press either the TYPE or the SEEK arrows to select and to take you to the PTY???s ???rst station.
4.To go to another station within that PTY and the PTY is displayed, press either the TYPE or the SEEK arrows once. If the PTY is not displayed, go back to Step 1.
5.Press either the TYPE or the SEEK arrows to exit program type select mode.
SCAN: Scan the stations within a PTY by performing the following:
1.Press the TYPE button to activate program type select mode.
2.Turn the TYPE knob or press and release the TYPE button to select a PTY.
3.Once the desired PTY is displayed, press and hold either the TYPE or the SCAN arrows for two seconds, and the radio will begin scanning the stations in the PTY.
4.Press either the TYPE or the SCAN arrows to stop at a station.
BAND (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same program type. To turn alternate frequency on, press and hold BAND for two seconds. AF ON will appear on the display. The radio may switch to stations with a stronger frequency.
To turn alternate frequency off, press and hold BAND again for two seconds. AF OFF will appear on the display. The radio will not switch to other stations.
Setting Preset PTYs (RDS Only)
These pushbuttons have factory PTY presets. Up to
12 PTYs (six FM1 and six FM2), can be programmed on the six numbered pushbuttons, by performing the following steps:
1.Press BAND to select FM1 or FM2.
2.Press the TYPE button to activate program type select mode.
3.Turn the TYPE knob or press and release the TYPE button to select a PTY.
4.Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the PTY that was set will return.
5.Repeat the steps for each pushbutton.
RDS Messages
INFO (Information): If the current station has a message, INFO will appear on the display. Press this button to see the message. The message may display the artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the message will appear every three seconds. To scroll through the message, press and release the INFO button.
A new group of words will appear on the display after every press of this button. Once the complete message has been displayed, INFO will disappear from the display until another new message is received. The last message can be displayed by pressing the INFO button. You can view the last message until a new message is received or a different station is tuned to.
Radio Messages
CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If
CAL ERR appears on the display, it means that the radio has not been con???gured properly for the vehicle and must be returned to your GM dealer for service.
LOCKED: This message is displayed when the THEFTLOCK?? system has locked up. Take the vehicle to your GM dealer for service.
If any error occurs repeatedly, or if an error cannot be corrected, contact your GM dealer.
Playing a CD
If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition
or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source.
When a CD is inserted, the CD symbol will appear on the display. As each new track starts to play, the track number will appear on the display.
The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
If playing a
in skipping, difficulty in ???nding tracks, and/or difficulty in loading and ejecting. If these problems occur try a known good CD.
Do not add paper labels to CDs, they could get caught in the CD player.
If an error appears on the display, see ???CD Messages??? later in this section.
LOAD: Press this button to load CDs into the CD player. This CD player will hold up to six CDs.
To insert one CD, do the following:
1.Turn the ignition on.
2.Press and release the LOAD button.
3.Wait for the indicator light, located to the right of the slot, to turn green.
4.Load a CD. Insert the CD partway into the slot, label side up. The player will pull the CD in.
To insert multiple CDs, do the following:
1.Turn the ignition on.
2.Press and hold the LOAD button for two seconds.
You will hear a beep and the indicator light, located to the right of the slot, will begin to ???ash and MULTI LOAD # will appear on the display.
3.Once the light stops ???ashing and turns green, INSERT CD # will appear on the display, load
a CD. Insert the CD partway into the slot, label side up. The player will pull the CD in.
Once the CD is loaded, the indicator light will begin ???ashing again. Once the light stops ???ashing and turns green, you can load another CD. The
CD player takes up to six CDs. Do not try to load more than six.
To load more than one CD but less than six, complete Steps 1 through 3. When ???nished loading CDs,
press the LOAD button to cancel the loading function. The radio will begin to play the last CD loaded.
If more than one CD has been loaded, a number for each CD will appear on the display.
Playing a Speci???c Loaded CD
For every CD loaded, a number will appear on the display. To play a speci???c CD, ???rst press the CD AUX button, then press the numbered pushbutton that corresponds to the CD. A small bar will appear under the CD number that is playing and the track number will appear on the display.
If an error appears on the display, see ???CD Messages??? later in this section.
CD Z(Eject): Press this button to eject CD(s).
To eject the CD that is currently playing, press and release this button.
To eject multiple CDs, do the following:
1.Press and hold the CD eject button for ???ve seconds.
You will hear a beep and the indicator light, located to the right of the slot, will begin to ???ash and EJECT ALL will appear on the display.
2.Once the light stops ???ashing and turns green, REMOVE CD # will appear on the display. The CD will eject and can be removed.
Once the CD is removed, the indicator light will begin ???ashing again and another CD will eject.
To stop ejecting the CDs, press the LOAD or the eject button.
If the CD is not removed, after 25 seconds, the CD will be automatically pulled back into the player. If CD is pushed back into the player, before the 25 second time period is complete, the player will sense an error and will try to eject the CD several times before stopping.
Do not repeatedly press the CD eject button to eject a CD after you have tried to push it in manually. The player???s
{REV (Reverse): Press and hold this button to reverse quickly within a track. You will hear sound at a reduced volume. Release the button to play the passage. The elapsed time of the track will appear on the display.
FWD |(Forward): Press and hold this button to advance quickly within a track. You will hear sound at a reduced volume. Release the button to play the passage. The elapsed time of the track will appear on the display.
RPT (Repeat): With repeat, one track or an entire CD can be repeated.
To use repeat, do the following:
???To repeat the track you are listening to, press and release the RPT button. RPT will appear on the display. Press RPT again to turn off repeat play.
???To repeat the CD you are listening to, press and hold the RPT button for two seconds. RPT will appear on the display. Press RPT again to turn off repeat play.
RDM (Random): With random, you can listen to the tracks in random, rather than sequential, order, on one CD or on all of the CDs. To use random, do one of the following:
???To play the tracks on the CD you are listening to in random order, press and release the RDM button. RANDOM ONE will appear on the display. Press RDM again to turn off random play.
???To play the tracks on all of the CDs that are loaded in random order, press and hold RDM for more than two seconds. You will hear a beep and RANDOM ALL will appear on the display. Press RDM again to turn off random play.
AUTO EQ (Automatic Equalization): Press AUTO EQ to select the equalization setting while playing a CD. The equalization will be stored whenever a CD is played. For more information on AUTO EQ, see ???AUTO EQ??? listed previously in this section.
??SEEK ??: Press the left arrow to go to the start of the current track, if more than ten seconds have played. Press the right arrow to go to the next track. If either arrow is held or pressed more than once, the player will continue moving backward or forward through the CD.
??SCAN ??: To scan one CD, press and hold either SCAN arrow for more than two seconds until SCAN appears on the display and you hear a beep. The radio will go to the next track, play for 10 seconds, then go on to the next track. Press either SCAN arrow again, to stop scanning.
To scan all loaded CDs, press and hold either SCAN arrow for more than four seconds until CD SCAN appears on the display and you hear a beep. Use this feature to listen to 10 seconds of the ???rst track of each loaded CD. Press either SCAN arrow again, to stop scanning.
INFO (Information): Press this knob to see how long the current track has been playing. To change the default on the display, track or elapsed time, press the knob until you see the display you want, then hold
the knob until the display ???ashes. The selected display will now be the default.
BAND: Press this button to listen to the radio when a CD is playing. The inactive CD(s) will remain safely inside the radio for future listening.
Using Song List Mode
The
To save tracks into the song list feature, perform the following steps:
1.Turn the CD player on and load it with at least one CD. See ???LOAD CD??? listed previously in this section for more information.
2.Check to see that the CD changer is not in song list mode.
to turn it off.
3.Select the desired CD by pressing the numbered pushbutton and then use the SEEK or TYPE right arrow to locate the track to be saved. The track will begin to play.
4.Press and hold the SONG LIST button to save the track into memory. When SONG LIST is pressed, one beep will be heard immediately. After two seconds of continuously pressing the SONG LIST button, two beeps will sound to con???rm the
track has been saved.
5.Repeat Steps 3 and 4 for saving other selections.
To play the song list, press the SONG LIST button. One beep will be heard and
Seek through the song list by using the SEEK or TYPE arrows. Seeking past the last saved track will return
to the ???rst saved track.
To delete tracks from the song list, perform the following steps:
1.Turn the CD player on.
2.Press the SONG LIST button to turn song list on.
3.Press either SEEK or TYPE arrow to select the desired track to be deleted.
4.Press and hold the SONG LIST button for two seconds. When SONG LIST is pressed, one
beep will be heard immediately. After two seconds of continuously pressing the SONG LIST button, two beeps will be heard to con???rm that the track has been deleted.
After a track has been deleted, the remaining tracks are moved up the list. When another track is added to the song list, the track will be added to the end of the list.
To delete the entire song list, perform the following steps:
1.Turn the CD player on.
2.Press the SONG LIST button to turn song list on.
3.Press and hold the SONG LIST button for more than four seconds. One beep will be heard, followed by two beeps after two seconds, and a ???nal beep will be heard after four seconds.
If a CD is ejected, and the song list contains saved tracks from that CD, those tracks are automatically deleted from the song list. Any tracks saved to the song list again are added to the bottom of the list.
To end song list mode, press the SONG LIST button. One beep will be heard and
CD Messages
CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons:
???It is very hot. When the temperature returns to normal, the CD should play.
???You are driving on a very rough road. When the road becomes smoother, the CD should play.
???The CD is dirty, scratched, wet, or upside down.
???The air is very humid. If so, wait about an hour and try again.
???There may have been a problem while burning the CD.
???The label may be caught in the CD player.
If the CD is not playing correctly, for any other reason, try a known good CD.
If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer. If the radio displays an error message, write it down and provide it to
your GM dealer when reporting the problem.
Radios)
THEFTLOCK?? is designed to discourage theft of your vehicle???s radio. The feature works automatically by learning a portion of the Vehicle Identi???cation Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOC will appear on the display.
With THEFTLOCK?? activated, the radio will not operate if stolen.
Radios)
THEFTLOCK?? is designed to discourage theft of your vehicle???s radio. The feature works automatically by learning a portion of the Vehicle Identi???cation Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOCKED will appear on the display.
When the radio and vehicle are turned off, the blinking red light indicates that THEFTLOCK?? is armed.
With THEFTLOCK?? activated, the radio will not operate if stolen.
Radio Reception
AM
The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise.
FM
FM stereo will give you the best sound, but FM signals will reach only about 10 to 40 miles (16 to 65 km).
Tall buildings or hills can interfere with FM signals, causing the sound to come and go.
Care of Your CDs
Handle CDs carefully. Store them in their original cases or other protective cases and away from direct
sunlight and dust. If the surface of a CD is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Be sure never to touch the side without writing when handling CDs. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge.
Care of Your CD Player
The use of CD lens cleaners for CD players is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism.
Fixed Mast Antenna
The ???xed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, straighten it out by hand. If the mast is badly bent, replace it.
Check occasionally to make sure the mast is still tightened to the fender. If tightening is required, tighten by hand, then with a wrench one quarter turn.
XM??? Satellite Radio Antenna
System
The XM??? Satellite Radio antenna is located on the roof of your vehicle. Keep this antenna clear of snow and ice build up for clear radio reception.
Chime Level Adjustment
The radio is the vehicle chime producer. To change the volume level, press and hold pushbutton 6 with the ignition on and the radio power off. The chime volume level will change from the normal level to loud, and LOUD will appear on the radio display. To change back to the default or normal setting, press and hold pushbutton 6 again. The chime level will change from the loud level to normal, and NORMAL will appear
on the radio display. Each time the chime volume is changed, three chimes will sound as an example of the new volume selected. Removing the radio and not replacing it with a factory radio or chime module will disable vehicle chimes.
Section 4 Driving Your Vehicle
Your Driving, the Road, and
Your Vehicle
Defensive Driving
The best advice anyone can give about driving is: Drive defensively.
Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page
Defensive driving really means ???be ready for anything.??? On city streets, rural roads, or freeways, it means ???always expect the unexpected.???
Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what they might do. Be ready for their mistakes.
Defensive driving requires that a driver concentrate on the driving task. Anything that distracts from the driving task ??? such as concentrating on a cellular telephone call, reading, or reaching for something on the ???oor ??? makes proper defensive driving more difficult and can even cause a collision, with resulting injury. Ask a passenger to help do things like this, or pull off the road in a safe place to do them yourself. These simple defensive driving techniques could save your life.
Drunken Driving
Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor
to the highway death toll, claiming thousands of victims every year.
Alcohol affects four things that anyone needs to drive a vehicle:
???Judgment
???Muscular Coordination
???Vision
???Attentiveness
Police records show that almost half of all motor
Many adults ??? by some estimates, nearly half the adult population ??? choose never to drink alcohol, so they never drive after drinking. For persons under 21,
it is against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. But what if people do? How much is ???too much??? if someone plans to drive? It is a lot less than many might think. Although it depends on each person and situation, here is some general information on the problem.
The Blood Alcohol Concentration (BAC) of someone who is drinking depends upon four things:
???The amount of alcohol consumed
???The drinker???s body weight
???The amount of food that is consumed before and during drinking
???The length of time it has taken the drinker to consume the alcohol
According to the American Medical Association, a
180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had
It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person???s BAC would be close to 0.12 percent. A person
who consumes food just before or during drinking will have a somewhat lower BAC level.
There is a gender difference, too. Women generally have a lower relative percentage of body water
than men. Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks.
The law in most U.S. states, and throughout Canada, sets the legal limit at 0.08 percent. In some other countries, the limit is even lower. For example, it is 0.05 percent in both France and Germany. The
BAC limit for all commercial drivers in the United States is 0.04 percent.
The BAC will be over 0.10 percent after three to six drinks (in one hour). Of course, as we have seen,
it depends on how much alcohol is in the drinks, and how quickly the person drinks them.
But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching
0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent. Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of
0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having a collision. At a BAC level of 0.10 percent, the chance
of this driver having a collision is 12 times greater; at a level of 0.15 percent, the chance is 25 times greater!
The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. ???I will be careful??? is not the right answer. What if there is an emergency, a need to take sudden action, as when a child darts into the street? A person with even a moderate BAC might not be able to react quickly enough to avoid the collision.
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person???s system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking ??? driver or passenger ??? is in a crash, that person???s chance of being killed or permanently disabled is higher than if the person had not been drinking.
{CAUTION:
Drinking and then driving is very dangerous. Your re???exes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious ??? or even fatal ??? collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking. Ride home in a cab; or if you are with a group, designate a driver who will not drink.
Control of a Vehicle
You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road.
Sometimes, as when you are driving on snow or ice, it is easy to ask more of those control systems than
the tires and road can provide. That means you can lose control of your vehicle.
Braking
Braking action involves perception time and reaction time.
First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time.
Average reaction time is about
your vehicle and others is important.
And, of course, actual stopping distances vary greatly with the surface of the road (whether it is pavement or gravel); the condition of the road (wet, dry, icy); tire tread; the condition of your brakes; the weight of
the vehicle and the amount of brake force applied.
Avoid needless heavy braking. Some people drive in spurts ??? heavy acceleration followed by heavy braking ??? rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking.
That means better braking and longer brake life.
If your engine ever stops while you are driving, brake normally but do not pump your brakes. If you do,
the pedal may get harder to push down. If your engine stops, you will still have some power brake assist.
But you will use it when you brake. Once the power assist is used up, it may take longer to stop and the brake pedal will be harder to push.
Your vehicle has
When you start your engine and begin to drive away, your
If there is a problem with the
stay on. See
Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS:
A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
The
As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Remember:
the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have
Using
Do not pump the brakes. Just hold the brake pedal down ???rmly and let
but this is normal.
Braking in Emergencies
With
Traction Control System (TCS)
Your vehicle may have a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the rear wheels are spinning or beginning to lose traction. When this happens, the system reduces engine power and may also upshift the transmission to limit wheel spin.
You may feel or hear the system working, but this is normal.
The TCS button is located on your instrument panel. Press this button to
turn the TCS off and on.
When the traction control system is turned off, an indicator light on the button will illuminate.
If your vehicle is in cruise control when the traction control system begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely use it again, you may
TCS operates in all transmission shift lever positions. But the system can upshift the transmission only as high as the shift lever position you have chosen, so you should use the lower gears only when necessary. See
Automatic Transmission Operation on page
and/or Manual Transmission Operation on page
If there is a problem with TCS, TRACTION FAULT will be displayed on your Driver Information Center
(DIC). See DIC Warnings and Messages on page
When this warning is displayed, the system will not limit wheel spin. Adjust your driving accordingly.
To limit wheel spin, especially in slippery road conditions, you should always leave TCS on. But you can turn the system off if you ever need to. You should turn the system off if your vehicle ever gets stuck in sand, mud or snow and rocking the vehicle is required. See ???Rocking Your Vehicle To Get It Out??? under If You Are Stuck: In Sand, Mud, Ice or Snow on page
Steering
Power Steering
If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort.
Steering Tips
Driving on Curves
It is important to take curves at a reasonable speed.
A lot of the ???driver lost control??? accidents mentioned on the news happen on curves. Here is why:
Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
The traction of the tires against the road surface makes it possible for the vehicle to change its path when
you turn the front wheels. If there is no traction, inertia will keep the vehicle going in the same direction. If you have ever tried to steer a vehicle on wet ice, you will understand this.
The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While
you are in a curve, speed is the one factor you can control.
Suppose you are steering through a sharp curve. Then you suddenly accelerate. Both control systems ??? steering and acceleration ??? have to do their work where the tires meet the road. Adding the sudden acceleration can demand too much of those places. You can lose control.
What should you do if this ever happens? Ease up on the accelerator pedal, steer the vehicle the way you want it to go, and slow down.
Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds
are based on good weather and road conditions. Under less favorable conditions you will want to go slower.
If you need to reduce your speed as you approach
a curve, do it before you enter the curve, while your front wheels are straight ahead.
Try to adjust your speed so you can ???drive??? through the curve. Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway.
Steering in Emergencies
There are times when steering can be more effective than braking. For example, you come over a hill and ???nd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking ??? if you can stop in time. But sometimes you cannot; there is not room. That is the time for evasive action ??? steering around the problem.
Your vehicle can perform very well in emergencies like these. First apply your brakes.
See Braking on page
steer around the problem, to the left or right depending on the space available.
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o???clock positions, you
can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly.
You may ???nd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving.
If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of
the pavement. You can turn the steering wheel up to
the pavement edge. Then turn your steering wheel to go straight down the roadway.
Passing
The driver of a vehicle about to pass another on a
Not necessarily! Passing another vehicle on a
So here are some tips for passing:
???Drive ahead. Look down the road, to the sides and to crossroads for situations that might affect your passing patterns. If you have any doubt whatsoever about making a successful pass, wait for a
better time.
???Watch for traffic signs, pavement markings and lines. If you can see a sign up ahead that might indicate a turn or an intersection, delay your pass. A broken center line usually indicates it is all
right to pass, providing the road ahead is clear. Never cross a solid line on your side of the lane or a double solid line, even if the road seems empty of approaching traffic.
???Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Keep back a reasonable distance.
???When it looks like a chance to pass is coming up, start to accelerate but stay in the right lane and do not get too close. Time your move so you will be increasing speed as the time comes to move into the other lane. If the way is clear to pass, you will have a running start that more than makes up for the distance you would lose by dropping back. And if something happens to cause you to cancel your pass, you need only slow down and drop back again and wait for another opportunity.
???If other vehicles are lined up to pass a slow vehicle, wait your turn. But take care that someone is not trying to pass you as you pull out to pass the slow vehicle. Remember to glance over your shoulder and check the blind spot.
???Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane. Remember that your right outside mirror is convex. The vehicle you just passed may seem to be farther away from you than it really is.
???Try not to pass more than one vehicle at a time on
???Do not overtake a slowly moving vehicle too rapidly. Even though the brake lamps are not ???ashing, it may be slowing down or starting to turn.
???If you are being passed, make it easy for the following driver to get ahead of you. Perhaps you can ease a little to the right.
Loss of Control
Let us review what driving experts say about what happens when the three control systems ??? brakes, steering, and acceleration ??? do not have enough friction where the tires meet the road to do what the driver has asked.
In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger.
Skidding
In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible.
The three types of skids correspond to your vehicle???s three control systems. In the braking skid, your wheels are not rolling. In the steering or cornering skid, too much speed or steering in a curve causes tires to slip and lose cornering force. And in the acceleration skid, too much throttle causes the driving wheels to spin.
A cornering skid is best handled by easing your foot off the accelerator pedal.
If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready
for a second skid if it occurs.
Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, you will want to slow down and adjust your driving to
these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including engine braking by shifting to a
lower gear. Any sudden changes could cause the tires to slide. You may not realize the surface is slippery
until your vehicle is skidding. Learn to recognize warning clues ??? such as enough water, ice, or packed snow
on the road to make a mirrored surface ??? and slow down when you have any doubt.
Remember: Any
This
Also, see
If your vehicle does not have
road signs. Surfaces can be slippery, rough, uphill or downhill. In short, you have gone right back to nature.
Before You Go
There are some things to do before you go out. For example, be sure to have all necessary maintenance and service work done. Check to make sure all underbody shields (if so equipped) are properly attached. Be sure you read all the information about your
there enough fuel? Is the spare tire fully in???ated? Are the ???uid levels up where they should be? What are the local laws that apply to
Loading Your Vehicle for
There are some important things to remember about how to load your vehicle.
???The heaviest things should be on the load ???oor and forward of your rear axle. Put heavier items as far forward as you can.
???Be sure the load is secured properly, so driving on the
{CAUTION:
???Cargo on the load ???oor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks.
???Unsecured cargo on the load ???oor can be tossed about when driving over rough terrain. You or your passengers can be struck by ???ying objects. Secure the cargo properly.
???Heavy loads on the roof raise the vehicle???s center of gravity, making it more likely to roll over. You can be seriously or fatally injured if the vehicle rolls over. Put heavy loads inside the cargo area, not on the roof. Keep cargo in the cargo area as far forward and low as possible.
You will ???nd other important information in this manual. See Loading Your Vehicle on page
on page
Environmental Concerns
the environment:
???Always use established trails, roads and areas that have been specially set aside for public
???Avoid any driving practice that could damage the environment ??? shrubs, ???owers, trees, grasses ??? or disturb wildlife (this includes
???Always carry a litter bag ??? make sure all refuse is removed from any campsite before leaving.
???Take extreme care with open ???res (where permitted), camp stoves and lanterns.
???Never park your vehicle over dry grass or other combustible materials that could catch ???re from the heat of the vehicle???s exhaust system.
Traveling to Remote Areas
It makes sense to plan your trip, especially when going to a remote area. Know the terrain and plan your route. You are much less likely to get bad surprises. Get accurate maps of trails and terrain. Try to learn of any blocked or closed roads.
It is also a good idea to travel with at least one other vehicle. If something happens to one of them, the other can help quickly.
Does your vehicle have a winch? If so, be sure to read the winch instructions. In a remote area, a winch
can be handy if you get stuck. But you will want to know how to use it properly.
Getting Familiar with
It is a good idea to practice in an area that is safe and close to home before you go into the wilderness.
Tune your senses to different kinds of signals. Your eyes, for example, need to constantly sweep the terrain for unexpected obstacles. Your ears need to listen
for unusual tire or engine sounds. With your arms, hands, feet and body, you will need to respond to vibrations and vehicle bounce.
Controlling your vehicle is the key to successful
is to control your speed. Here are some things to keep in mind. At higher speeds:
???you approach things faster and you have less time to scan the terrain for obstacles.
???you have less time to react.
???you have more vehicle bounce when you drive over obstacles.
???you will need more distance for braking, especially since you are on an unpaved surface.
{CAUTION:
When you are driving
Scanning the Terrain
and its many different features. Here are some things to consider.
Surface Conditions:
Surface Obstacles: Unseen or hidden obstacles can be hazardous. A rock, log, hole, rut or bump can startle you if you are not prepared for them. Often these obstacles are hidden by grass, bushes, snow or even the rise and fall of the terrain itself. Here are some things to consider:
???Is the path ahead clear?
???Will the surface texture change abruptly up ahead?
???Does the travel take you uphill or downhill? (There is more discussion of these subjects later.)
???Will you have to stop suddenly or change direction quickly?
When you drive over obstacles or rough terrain, keep a ???rm grip on the steering wheel. Ruts, troughs or
other surface features can jerk the wheel out of your hands if you are not prepared.
When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground. If this happens, even with one or two wheels, you cannot control the vehicle as well or at all.
Because you will be on an unpaved surface, it is especially important to avoid sudden acceleration, sudden turns or sudden braking.
In a way,
signal lights. You have to use your own good judgment about what is safe and what is not.
Drinking and driving can be very dangerous on any road. And this is certainly true for
skills, your re???exes, perceptions and judgment can be affected by even a small amount of alcohol. You could have a serious ??? or even fatal ??? accident if you drink and drive or ride with a driver who has been drinking. See Drunken Driving on page
Driving on
{CAUTION:
Many hills are simply too steep for any vehicle. If you drive up them, you will stall. If you drive down them, you cannot control your speed. If you drive across them, you will roll over. You could be seriously injured or killed. If you have any doubt about the steepness, do not drive the hill.
Approaching a Hill
When you approach a hill, you need to decide if it is one of those hills that is just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where
you can easily see all the way to the top. On a large hill, the incline may get steeper as you near the top, but you may not see this because the crest of the hill
is hidden by bushes, grass or shrubs.
Here are some other things to consider as you approach
ahill.
???Is there a constant incline, or does the hill get sharply steeper in places?
???Is there good traction on the hillside, or will the surface cause tire slipping?
???Is there a straight path up or down the hill so you will not have to make turning maneuvers?
???Are there obstructions on the hill that can block your path (boulders, trees, logs or ruts)?
???What is beyond the hill? Is there a cliff, an embankment, a
???Is the hill simply too rough? Steep hills often have ruts, gullies, troughs and exposed rocks because they are more susceptible to the effects of erosion.
Driving Uphill
Once you decide you can safely drive up the hill, you need to take some special steps.
???Use a low gear and get a ???rm grip on the steering wheel.
???Get a smooth start up the hill and try to maintain your speed. Do not use more power than you need, because you do not want your wheels to start spinning or sliding.
???Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to ???nd another route.
{CAUTION:
Turning or driving across steep hills can be dangerous. You could lose traction, slide sideways, and possibly roll over. You could be seriously injured or killed. When driving up hills, always try to go straight up.
???Ease up on your speed as you approach the top of the hill.
???Attach a ???ag to the vehicle to make you more visible to approaching traffic on trails or hills.
???Sound the horn as you approach the top of the hill to let opposing traffic know you are there.
???Use your headlamps even during the day. They make you more visible to oncoming traffic.
{CAUTION:
Driving to the top (crest) of a hill at full speed can cause an accident. There could be a
Q: What should I do if my vehicle stalls, or is about to stall, and I cannot make it up the hill?
A: If this happens, there are some things you should do, and there are some things you must not do. First, here is what you should do:
???Push the brake pedal to stop the vehicle and keep it from rolling backwards. Also, apply the parking brake.
???If your engine is still running, shift the transmission to REVERSE (R), release the parking brake, and slowly back down the hill in REVERSE (R).
???If your engine has stopped running, you will need to restart it. With the brake pedal pressed and the parking brake still applied, shift the transmission to PARK (P) (or shift to NEUTRAL if your vehicle
has a manual transmission) and restart the engine. Then, shift to REVERSE (R), release the parking brake, and slowly back down the hill as straight as possible in REVERSE (R).
???As you are backing down the hill, put your left hand on the steering wheel at the 12 o???clock position. This way, you will be able to tell if your wheels are straight and maneuver as you back down. It is best that you back down the hill with your wheels straight rather than in the left or right direction. Turning the wheel too far to the left or right will increase the possibility of a rollover.
Here are some things you must not do if you stall, or are about to stall, when going up a hill.
???Never attempt to prevent a stall by shifting into NEUTRAL (N) (or pressing the clutch, if you have a manual transmission) to
Instead, apply the regular brake to stop the vehicle. Then apply the parking brake. Shift to REVERSE (R), release the parking brake, and slowly back straight down.
???Never attempt to turn around if you are about to stall when going up a hill. If the hill is steep enough to stall your vehicle, it is steep enough to cause you to roll over if you turn around. If you cannot make it up the hill, you must back straight down the hill.
Q: Suppose, after stalling, I try to back down the hill and decide I just cannot do it. What should
Ido?
A:Set the parking brake, put your transmission in PARK (P) (or the manual transmission in FIRST (1)) and turn off the engine. Leave the vehicle and go get some help. Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill.
Driving Downhill
When
???How steep is the downhill? Will I be able to maintain vehicle control?
???What is the surface like? Smooth? Rough? Slippery?
???Are there hidden surface obstacles? Ruts? Logs? Boulders?
???What is at the bottom of the hill? Is there a hidden creek bank or even a river bottom with large rocks?
If you decide you can go down a hill safely, then try to keep your vehicle headed straight down, and use a low gear. This way, engine drag can help your brakes and they will not have to do all the work. Descend slowly, keeping your vehicle under control at all times.
{CAUTION:
Heavy braking when going down a hill can cause your brakes to overheat and fade. This could cause loss of control and a serious accident. Apply the brakes lightly when descending a hill and use a low gear to keep vehicle speed under control.
Q: Are there some things I should not do when driving down a hill?
A: Yes! These are important because if you ignore them you could lose control and have a serious accident.
???When driving downhill, avoid turns that take you across the incline of the hill. A hill that is not too steep to drive down may be too steep to drive across. You could roll over if you do not drive straight down.
???Never go downhill with the transmission in NEUTRAL (N), or with the clutch pedal pressed down with a manual transmission. This is called
Q: Am I likely to stall when going downhill?
A: It is much more likely to happen going uphill. But if it happens going downhill, here is what to do.
1.Stop your vehicle by applying the regular brakes. Apply the parking brake.
2.Shift to PARK (P) (or to NEUTRAL with the manual transmission) and, while still braking, restart the engine.
3.Shift back to a low gear, release the parking brake, and drive straight down.
4.If the engine will not start, get out and get help.
Driving Across an Incline
Sooner or later, an
???A hill that can be driven straight up or down may be too steep to drive across. When you go straight up or down a hill, the length of the wheel base (the distance from the front wheels to the rear wheels) reduces the likelihood the vehicle will tumble end over end. But when you drive across an incline, the much more narrow track width (the distance between the left and right wheels) may not prevent the vehicle from tilting and rolling over. Also, driving across an incline puts more weight on the downhill wheels. This could cause a downhill slide or a rollover.
???Surface conditions can be a problem when you drive across a hill. Loose gravel, muddy spots, or even wet grass can cause your tires to slip sideways, downhill. If the vehicle slips sideways, it can hit something that will trip it (a rock, a rut, etc.) and roll over.
???Hidden obstacles can make the steepness of the incline even worse. If you drive across a rock with the uphill wheels, or if the downhill wheels drop into a rut or depression, your vehicle can tilt even more.
For reasons like these, you need to decide carefully whether to try to drive across an incline. Just because the trail goes across the incline does not mean you have to drive it. The last vehicle to try it might have rolled over.
{CAUTION:
Driving across an incline that is too steep will make your vehicle roll over. You could be seriously injured or killed. If you have any doubt about the steepness of the incline, do not drive across it. Find another route instead.
Q: What if I am driving across an incline that is not too steep, but I hit some loose gravel and start to slide downhill. What should I do?
A: If you feel your vehicle starting to slide sideways, turn downhill. This should help straighten out the vehicle and prevent the side slipping. However,
a much better way to prevent this is to get out and ???walk the course??? so you know what the surface
is like before you drive it.
Stalling on an Incline
If your vehicle stalls when you are crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you
get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
If you have to walk down the slope, stay out of the path the vehicle will take if it does roll over.
{CAUTION:
Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over, you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path.
Driving in Mud, Sand, Snow or Ice
When you drive in mud, snow or sand, your wheels will not get good traction. You cannot accelerate as
quickly, turning is more difficult, and you will need longer braking distances.
It is best to use a low gear when you are in mud ??? the deeper the mud, the lower the gear. In really deep mud, the idea is to keep your vehicle moving so you do not get stuck.
When you drive on sand, you will sense a change in wheel traction. But it will depend upon how loosely packed the sand is. On loosely packed sand (as
on beaches or sand dunes) your tires will tend to sink into the sand. This has an effect on steering, accelerating and braking. Drive at a reduced speed and avoid sharp turns or abrupt maneuvers.
Hard packed snow and ice offer the worst tire traction. On these surfaces, it is very easy to lose control.
On wet ice, for example, the traction is so poor that you will have difficulty accelerating. And if you do get moving, poor steering and difficult braking can cause you to slide out of control.
{CAUTION:
Driving on frozen lakes, ponds or rivers can be dangerous. Underwater springs, currents under the ice, or sudden thaws can weaken the ice. Your vehicle could fall through the ice and you and your passengers could drown. Drive your vehicle on safe surfaces only.
Driving in Water
Heavy rain can mean ???ash ???ooding, and ???ood waters demand extreme caution.
Find out how deep the water is before you drive through it. If it is deep enough to cover your wheel hubs,
axles or exhaust pipe, do not try it ??? you probably will not get through. Also, water that deep can damage your axle and other vehicle parts.
If the water is not too deep, drive slowly through it. At faster speeds, water splashes on your ignition system and your vehicle can stall. Stalling can also occur if you get your tailpipe under water. And, as long as your tailpipe is under water, you will never be
able to start your engine. When you go through water, remember that when your brakes get wet, it may
take you longer to stop.
{CAUTION:
Driving through rushing water can be dangerous. Deep water can sweep your vehicle downstream and you and your passengers could drown. If it is only shallow water, it can still wash away the ground from under your tires, and you could lose traction and roll
the vehicle over. Do not drive through rushing water.
See Driving in Rain and on Wet Roads on page
After
Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a ???re hazard.
After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking. Check the body structure, steering, suspension, wheels, tires and exhaust system for damage. Also, check the fuel lines and cooling system for any leakage.
Your vehicle will require more frequent service due to
for additional information.
Driving at Night
Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired ??? by alcohol or drugs, with night vision problems, or by fatigue.
Here are some tips on night driving.
???Drive defensively.
???Do not drink and drive.
???Adjust your inside rearview mirror to reduce the glare from headlamps behind you.
???Since you cannot see as well, you may need to slow down and keep more space between you and other vehicles.
???Slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead.
???In remote areas, watch for animals.
???If you are tired, pull off the road in a safe place and rest.
No one can see as well at night as in the daytime. But as we get older these differences increase. A
What you do in the daytime can also affect your
night vision. For example, if you spend the day in bright sunshine you are wise to wear sunglasses. Your
eyes will have less trouble adjusting to night. But if you are driving, do not wear sunglasses at night. They may cut down on glare from headlamps, but they also make a lot of things invisible.
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to
who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little. Avoid staring directly into the approaching headlamps.
Keep your windshield and all the glass on your vehicle clean ??? inside and out. Glare at night is made much worse by dirt on the glass. Even the inside of the glass can build up a ???lm caused by dust. Dirty glass makes lights dazzle and ???ash more than clean glass would, making the pupils of your eyes contract repeatedly.
Remember that your headlamps light up far less of a roadway when you are in a turn or curve. Keep
your eyes moving; that way, it is easier to pick out dimly lighted objects. Just as your headlamps should be checked regularly for proper aim, so should your eyes be examined regularly. Some drivers suffer from
night blindness ??? the inability to see in dim light ??? and are not even aware of it.
Driving in Rain and on Wet Roads
Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your
you are driving. The surface may get wet suddenly when your re???exes are tuned for driving on dry pavement.
The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and
traffic signals, pavement markings, the edge of the road, and even people walking.
It is wise to keep your wiping equipment in good shape and keep your windshield washer tank ???lled with washer ???uid. Replace your windshield wiper inserts when they show signs of streaking or missing areas on the windshield, or when strips of rubber start to separate from the inserts.
Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you cannot, try to slow down before you hit them.
{CAUTION:
Wet brakes can cause accidents. They will not work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle.
After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally.
Hydroplaning
Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Hydroplaning does not happen often. But it can if your tires do not have much tread or if the pressure in one or more is low. It can happen if a lot of water is standing on the road. If you can see re???ections from trees, telephone poles, or other vehicles, and raindrops dimple the water???s surface, there could be hydroplaning.
Hydroplaning usually happens at higher speeds. There just is not a hard and fast rule about hydroplaning. The best advice is to slow down when it is raining.
Driving Through Deep Standing Water
Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine???s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle. If you cannot avoid deep puddles or standing water, drive through them very slowly.
Driving Through Flowing Water
{CAUTION:
Flowing or rushing water creates strong forces. If you try to drive through ???owing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of ???owing water can carry away a smaller vehicle. If this happens, you and other vehicle occupants could drown. Do not ignore police warning signs, and otherwise be very cautious about trying to drive through ???owing water.
Some Other Rainy Weather Tips
???Besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle. Allow yourself more clear room ahead, and be prepared to have your
view restricted by road spray.
???Have good tires with proper tread depth. See Tires on page
City Driving
One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals.
Here are ways to increase your safety in city driving:
???Know the best way to get to where you are going. Get a city map and plan your trip into
an unknown part of the city just as you would for a
???Try to use the freeways that rim and crisscross most large cities. You will save time and energy. See Freeway Driving on page
???Treat a green light as a warning signal. A traffic light is there because the corner is busy enough
to need it. When a light turns green, and just before you start to move, check both ways for vehicles that have not cleared the intersection or may
be running the red light.
Freeway Driving
Mile for mile, freeways ??? also called thruways, parkways, expressways, turnpikes, or superhighways ??? are the safest of all roads. But they have their own special rules.
The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the
same speed most of the other drivers are driving.
At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the ???ow. Try to merge into the gap at close to the prevailing speed. Switch on your turn signal, check your mirrors, and glance over your shoulder as often as necessary. Try to blend smoothly with the traffic ???ow.
Once you are on the freeway, adjust your speed to the posted limit or to the prevailing rate if it is slower.
Stay in the right lane unless you want to pass.
Before changing lanes, check your mirrors. Then use your turn signal.
Just before you leave the lane, glance quickly over your shoulder to make sure there is not another vehicle in your blind spot.
Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night.
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit.
The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Reduce your speed according to your speedometer, not to your sense of motion. After driving for any distance at higher speeds, you may tend to think you are
going slower than you actually are.
Before Leaving on a Long Trip
Make sure you are ready. Try to be well rested. If you must start when you are not fresh ??? such as after
a day???s work ??? do not plan to make too many miles that ???rst part of the journey. Wear comfortable clothing
and shoes you can easily drive in.
Is your vehicle ready for a long trip? If you keep it serviced and maintained, it is ready to go. If it needs service, have it done before starting out. Of course, you will ???nd experienced and able service experts in GM dealerships all across North America. They will be ready and willing to help if you need it.
Here are some things you can check before a trip:
???Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside?
???Wiper Blades: Are they in good shape?
???Fuel, Engine Oil, Other Fluids: Have you checked all levels?
???Lamps: Are they all working? Are the lenses clean?
???Tires: They are vitally important to a safe,
???Weather Forecasts: What is the weather outlook along your route? Should you delay your trip a short time to avoid a major storm system?
???Maps: Do you have
Highway Hypnosis
Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever.
There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the
wind against the vehicle that can make you sleepy. Do not let it happen to you! If it does, your vehicle can leave the road in less than a second, and you could crash and be injured.
What can you do about highway hypnosis? First, be aware that it can happen.
Then here are some tips:
???Make sure your vehicle is well ventilated, with a comfortably cool interior.
???Keep your eyes moving. Scan the road ahead and to the sides. Check your mirrors and your instruments frequently.
???If you get sleepy, pull off the road into a rest, service, or parking area and take a nap, get some exercise, or both. For safety, treat drowsiness
on the highway as an emergency.
Hill and Mountain Roads
Driving on steep hills or mountains is different from driving in ???at or rolling terrain.
If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. See
page
???Keep your vehicle in good shape. Check all ???uid levels and also the brakes, tires, cooling system, and transmission. These parts can work hard on mountain roads.
???Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill.
{CAUTION:
If you do not shift down, your brakes could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Shift down to let your engine assist your brakes on a steep downhill slope.
{CAUTION:
Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have your engine running and your vehicle in gear when you go downhill.
???Know how to go uphill. You may want to shift down to a lower gear. The lower gears help cool your engine and transmission, and you can climb the hill better.
???Stay in your own lane when driving on
???As you go over the top of a hill, be alert. There could be something in your lane, like a stalled car or an accident.
???You may see highway signs on mountains that warn of special problems. Examples are long grades, passing or
Winter Driving
Here are some tips for winter driving:
???Have your vehicle in good shape for winter.
???You may want to put winter emergency supplies in your vehicle.
Also see Tires on page
Include an ice scraper, a small brush or broom, a supply of windshield washer ???uid, a rag, some winter outer clothing, a small shovel, a ???ashlight, a red
cloth, and a couple of re???ective warning triangles. And, if you will be driving under severe conditions, include
a small bag of sand, a piece of old carpet or a couple of burlap bags to help provide traction. Be sure you properly secure these items in your vehicle.
Driving on Snow or Ice
Most of the time, those places where your tires meet the road probably have good traction.
However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction, or grip, and will need to be very careful.
What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32??F; 0??C) and freezing rain begins to fall. Try to avoid driving on wet ice until salt and sand crews can get there.
Whatever the condition ??? smooth ice, packed, blowing, or loose snow ??? drive with caution.
Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more.
Your
???Allow greater following distance on any slippery road.
???Watch for slippery spots. The road might be ???ne until you hit a spot that is covered with ice. On an otherwise clear road, ice patches may appear in shaded areas where the sun cannot reach: around clumps of trees, behind buildings, or under bridges. Sometimes the surface of a curve or an overpass may remain icy when the surrounding roads are clear. If you see a patch of ice ahead of you, brake before you are on it. Try not to brake while you are actually on the ice, and avoid sudden steering maneuvers.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
If You Are Stuck: In Sand, Mud, Ice or Snow
In order to free your vehicle when it is stuck, you will need to spin the wheels, but you do not want to
spin your wheels too fast. The method known as rocking can help you get out when you are stuck, but you
must use caution.
{CAUTION:
If you let your tires spin at high speed, they can explode, and you or others could be injured. And, the vehicle can overheat. That could cause an engine compartment ???re or other damage. When you are stuck, spin the wheels as little as possible. Do not spin the wheels above 35 mph (55 km/h) as shown on the speedometer.
Notice: Spinning your wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting your transmission back and forth, you can destroy your transmission.
For information about using tire chains on your vehicle, see Tire Chains on page
Rocking Your Vehicle to Get It Out
First, turn your steering wheel left and right. That
will clear the area around your front wheels. If you have a
Traction Control System (TCS) on page
a forward gear (or with a manual transmission, between FIRST (1) or SECOND (2) and REVERSE (R)), spinning the wheels as little as possible. Release the accelerator pedal while you shift, and press lightly on the accelerator pedal when the transmission is in gear.
By slowly spinning your wheels in the forward and reverse directions, you will cause a rocking motion that may free your vehicle. If that does not get you out
after a few tries, you may need to be towed out. Or, you can use your recovery hooks if your vehicle has
them. If you do need to be towed out, see Towing Your Vehicle on page
Recovery Hooks
Your vehicle may be equipped with recovery hooks. The hooks are provided at the front of your vehicle. You may need to use them if you are stuck
{CAUTION:
These hooks, when used, are under a lot of force. Always pull the vehicle straight out. Never pull on the hooks at a sideways angle. The hooks could break off and you or others could be injured from the chain or cable snapping back.
Notice: Never use recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty.
Loading Your Vehicle
It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo and all
{CAUTION:
Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle.
Tire and Loading Information Label
Label Example
A vehicle speci???c Tire and Loading Information is attached to the vehicle???s center pillar
tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire in???ation pressures (D). For more information on tires and in???ation see Tires on page
There is also important information on the Certi???cation/Tire label. It tells you the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axles. See ???Certi???cation/Tire Label??? later in this section.
Steps for Determining Correct Load Limit
1.Locate the statement ???The combined weight of occupants and cargo should never exceed XXX kg or XXX pounds??? on your vehicle???s placard.
2.Determine the combined weight of the driver and passengers that will be riding in your vehicle.
3.Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.
4.The resulting ???gure equals the available amount of cargo and luggage load capacity. For example, if the ???XXX??? amount equals 1400 lbs and there will be ???ve 150 lb passengers in your vehicle, the amount
of available cargo and luggage load capacity is 650 lbs (1400 ??? 750 (5 x 150) = 650 lbs).
5.Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo
and luggage load capacity calculated in Step 4.
6.If your vehicle will be towing a trailer, the load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
See Towing a Trailer on page
Example 1
Example 2
Example 3
Refer to your vehicle???s tire and loading information label for speci???c information about your vehicle???s capacity weight and seating positions. The combined weight of the driver, passengers, cargo and any accessories or equipment added to your vehicle after it left the factory should never exceed your vehicle???s capacity weight.
Certi???cation/Tire Label
Label Example
A vehicle speci???c Certi???cation/Tire label is attached to the bottom section of the center pillar, on the driver???s side of the vehicle. Vehicles without a center pillar, extended cab models, will have the Certi???cation/Tire label attached to the edge of the driver???s side, extended cab door, below the door latch post. The label shows the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants,
fuel, cargo and trailer tongue weight, if pulling a trailer.
The Certi???cation/Tire label also tells you the maximum weights for the front and rear axles, called Gross
Axle Weight Rating (GAWR). To ???nd out the actual loads on your front and rear axles, you need to go to a
weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline.
Never exceed the GVWR for your vehicle, or the GAWR for either the front or rear axle.
If you do have a heavy load, you should spread it out.
Similar appearing vehicles may have different GVWRs and capacity weights. Please note your vehicle???s Certi???cation/Tire label or consult your dealer for additional details.
{CAUTION:
Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle.
Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way.
Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle.
If you put things inside your vehicle ??? like suitcases, tools, packages, or anything else ??? they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they???ll keep going.
{CAUTION:
Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
???Put things in the cargo area of your vehicle. Try to spread the weight evenly.
???Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats.
???Do not leave an unsecured child restraint in your vehicle.
???When you carry something inside the vehicle, secure it whenever you can.
???Do not leave a seat folded down unless you need to.
There???s also important loading information for
for
Remember not to exceed the Gross Axle Weight Rating (GAWR) of the front or rear axle.
By positioning four 2??? X 6??? wooden planks across the width of the pickup box, you can create an upper
load platform. The planks must be inserted in the pickup box depressions. The length of the planks must allow for at least a 3/4 inch (2 cm) bearing surface on
each end of the plank.
When using this upper load platform, be sure the load is securely tied down to prevent it from shifting. The load???s center of gravity should be positioned in a zone over the rear axle.
Any load that extends beyond the vehicle???s taillamp area must be properly marked according to local laws and regulations.
Remember not to exceed the Gross Axle Weight Rating (GAWR) of the rear axle.
When you carry removable items, you may need to put a limit on how many people you carry inside your vehicle. Be sure to weigh your vehicle before you buy and install the new equipment.
Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle.
Remember not to exceed the Gross Axle Weight Rating (GAWR) of the rear axle.
Your vehicle was not designed to carry a
Pickup Conversion to Chassis Cab
General Motors is aware that some vehicle owners may consider having the pickup box removed and a commercial or recreational body installed. However, we recommend that conversions of this type not be done
to pickups. Owners should be aware that, as manufactured, there are differences between a chassis cab and a pickup with the box removed which may affect vehicle safety. For speci???c information on
this pickup, contact GM Customer Assistance. See
Customer Assistance Offices on page
Towing
Towing Your Vehicle
Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See
Roadside Assistance Program on page
If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see ???Recreational Vehicle Towing??? following.
Recreational Vehicle Towing
Recreational vehicle towing means towing your vehicle behind another vehicle ??? such as behind a motorhome. The two most common types of recreational vehicle towing are known as ???dinghy??? (towing your vehicle with all four wheels on the ground) and ???dolly??? (towing
your vehicle with two wheels on the ground and two wheels up on a device known as a ???dolly???).
With the proper preparation and equipment, many vehicles can be towed in these ways. See ???Dinghy Towing??? and ???Dolly Towing??? following.
Here are some important things to consider before you do recreational vehicle towing:
???What???s the towing capacity of the towing vehicle? Be sure you read the tow vehicle manufacturer???s recommendations.
???How far will you tow? Some vehicles have restrictions on how far and how long they can tow.
???Do you have the proper towing equipment? See your dealer or trailering professional for
additional advice and equipment recommendations.
???Is your vehicle ready to be towed? Just as you would prepare your vehicle for a long trip, you???ll want to make sure your vehicle is prepared to be towed.
Dinghy Towing
Notice: If you tow your vehicle with all four wheels on the ground, the drivetrain components could
be damaged. The repairs would not be covered by your warranty. Do not tow your vehicle with all four wheels on the ground.
Use the following procedure to tow your vehicle with all four wheels on the ground:
1.Drive the vehicle to be towed into position behind the tow vehicle.
2.Firmly set the parking brake. See Parking Brake on page
3.Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1).
4.Securely attach the vehicle being towed to the tow vehicle.
For manual transmission vehicles, make sure the wheels are straight before proceeding to the
next steps. On automatic transmission vehicles, use an adequate clamping device to ensure that the front wheels are locked into the straight position.
{CAUTION:
Shifting a
5.Shift the transfer case to NEUTRAL. See
6.Release the parking brake only after the vehicle being towed is ???rmly attached to the tow vehicle.
7.Turn the ignition to LOCK.
If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from
the negative terminal (post) of the battery to prevent your battery from draining while towing.
After towing see ???Shifting Out of NEUTRAL??? under
Dolly Towing
Front Towing (Front Wheels Off the
Ground)
Notice: If you tow a
Use the following procedure to dolly tow your vehicle from the front:
1.Drive the vehicle onto the dolly.
2.Firmly set the parking brake. See Parking Brake on page
3.Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1).
4.Follow the dolly manufacturer???s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. Make sure the wheels are straight before towing.
{CAUTION:
Shifting a
5.Shift the transfer case to NEUTRAL. See
6.Release the parking brake only after the vehicle being towed is ???rmly attached to the tow vehicle.
7.Turn the ignition to LOCK.
If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from
the negative terminal (post) of the battery to prevent your battery from draining while towing.
After towing see ???Shifting Out of NEUTRAL??? under
Rear Towing (Rear Wheels Off the Ground)
Use the following procedure to tow your vehicle from the rear:
1.Drive the vehicle onto the dolly.
2.Firmly set the parking brake. See Parking Brake on page
3.Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1).
4.Follow the dolly manufacturer???s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. Make sure the wheels are straight before towing.
For manual transmission vehicles, make sure the wheels are straight before proceeding to the
next steps. On automatic transmission vehicles, use an adequate clamping device to ensure that the front wheels are locked into the straight position.
5.Release the parking brake only after the vehicle being towed is ???rmly attached to the tow vehicle.
6.Turn the ignition to LOCK.
If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from
the negative terminal (post) of the battery to prevent your battery from draining while towing.
Use the following procedure to tow your vehicle from the rear:
1.Drive the vehicle onto the dolly.
2.Firmly set the parking brake. See Parking Brake on page
3.Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1).
4.Follow the dolly manufacturer???s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle.
For manual transmission vehicles, make sure the wheels are straight before proceeding to the
next steps. On automatic transmission vehicles, use an adequate clamping device to ensure that the front wheels are locked into the straight position.
{CAUTION:
Shifting a
5.Shift the transfer case to NEUTRAL. See
6.Release the parking brake only after the vehicle being towed is ???rmly attached to the tow vehicle.
7.Turn the ignition to LOCK.
If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from
the negative terminal (post) of the battery to prevent your battery from draining while towing.
After towing, see ???Shifting Out of NEUTRAL??? under
Trailer Connections
If your vehicle is equipped with trailering provisions, see the instruction sheet in the glovebox for more information.
Trailer Recommendations
You must subtract your hitch load from the CWR for your vehicle. Weigh your vehicle with your trailer attached, so that you won???t go over the GVWR or the GAWR.
You???ll get the best performance if you spread out the weight of your load the right way, and if you choose the correct hitch and trailer brakes.
For more information, see Towing a Trailer on page
Towing a Trailer
{CAUTION:
If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well ??? or even at all. You and your passengers could be seriously injured. Pull a trailer only if you have followed all the steps in this section. Ask your dealer for advice and information about towing a trailer with your vehicle.
Notice: Pulling a trailer improperly can damage your vehicle and result in costly repairs that would not be covered by your warranty. Always follow the instructions in this section and check with your dealer for more information about towing a trailer with your vehicle.
To identify what the vehicle trailering capacity is for your vehicle, you should read the information in ???Weight of the Trailer??? that appears later in this section.
If yours was built with trailering options, as many are, it???s ready for heavier trailers. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, acceleration, braking, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly.
That???s the reason for this part. In it are many
these are important for your safety and that of your passengers. So please read this section carefully before you pull a trailer.
If You Do Decide To Pull A Trailer
If you do, here are some important points:
???There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live
but also where you???ll be driving. A good source for this information can be state or provincial police.
???Consider using a sway control. You can ask a hitch dealer about sway controls.
???Don???t tow a trailer at all during the ???rst
500 miles (800 km) your new vehicle is driven. Your engine, axle or other parts could be damaged.
???Then, during the ???rst 500 miles (800 km) that
you tow a trailer, don???t drive over 50 mph (80 km/h) and don???t make starts at full throttle. This helps your engine and other parts of your vehicle wear in at the heavier loads.
???You may want to shift the transmission to THIRD (3) or, if necessary, a lower gear selection if the transmission shifts too often (e.g., under heavy loads and/or hilly conditions). If you have a manual transmission and you are towing a trailer, it???s
better not to use the highest gear.
Three important considerations have to do with weight:
???the weight of the trailer,
???the weight of the trailer tongue
???and the weight on your vehicle???s tires.
Weight of the Trailer
How heavy can a trailer safely be?
It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on your vehicle.
The following chart shows how much your trailer can weigh, based upon your vehicle model and options.
Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required trailering equipment. The weight of additional optional equipment, passengers and cargo in the tow vehicle must be subtracted from the maximum trailer weight. The weight of the trailer tongue also affects trailering capacity. See ???Weight of the Trailer Tongue??? next.
**The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for your vehicle should not be exceeded.
You can ask your dealer for our trailering information or advice, or you can write us at the address listed in your Warranty and Owner Assistance Information Booklet.
In Canada, write to:
General Motors of Canada Limited
Customer Communication Centre,
1908 Colonel Sam Drive
Oshawa, Ontario L1H 8P7
Weight of the Trailer Tongue
The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle. If you have a lot of options, equipment, passengers or cargo in your vehicle, it will reduce the tongue weight your vehicle can carry, which will also reduce the trailer weight your vehicle can tow. And if you will tow a trailer, you must add the tongue load to the GVW because your vehicle will be carrying that weight, too. See Loading Your Vehicle on page
The trailer tongue weight (A) should be 10 percent to 15 percent of the total loaded trailer weight, up to a maximum of 500 lbs (226 kg) with a weight carrying hitch.
Do not exceed the maximum allowable tongue weight for your vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle.
After you???ve loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights
are proper. If they aren???t you may be able to get them right simply by moving some of the items around in the trailer.
Total Weight on Your Vehicle???s Tires
Be sure your vehicle???s tires are in???ated to the upper limit for cold tires. You???ll ???nd these numbers on the Certi???cation label at the rear edge of the driver???s door above the door latch, or see Loading Your Vehicle on page
Hitches
It???s important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you???ll need the right hitch.
Carrying Hitches
You can use your step bumper hitch for trailers up to 2,000 lbs (907 kg) total weight, and 200 lbs (90 kg) tongue weight.
Notice: If you use a
Safety Chains
You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. For trailers up to 2,000 lbs (907 kg) you may attach the safety chains to the attaching points on the bumper. For heavier trailers, follow the trailer or hitch manufacturer???s recommendation for attaching safety chains. Always leave just enough slack so you can turn with your rig. Never allow safety chains to drag on the ground.
Trailer Brakes
If your trailer weighs more than 1,000 lbs (450 kg) loaded, then it needs its own brakes ??? and they must be adequate. Be sure to read and follow the instructions for the trailer brakes so you???ll be able to install, adjust and maintain them properly.
Your trailer???s brake system can tap into the vehicle???s hydraulic brake system only if:
???The trailer parts can withstand 3,000 psi (20 650 kPa) of pressure.
???The trailer???s brake system will use less than
0.02 cubic inch (0.3 cc) of ???uid from your vehicle???s master cylinder. Otherwise, both braking systems won???t work well. You could even lose your brakes.
If everything checks out this far, then make the brake ???uid tap at the port on the master cylinder that
sends ???uid to the rear brakes. But don???t use copper tubing for this. If you do, it will bend and ???nally break off. Use steel brake tubing.
Driving with a Trailer
Towing a trailer requires a certain amount of experience. Before setting out for the open road, you???ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Before you start, check all trailer hitch parts and attachments, safety chains, electrical connector, lamps, tires and mirror adjustment.
If the trailer has electric brakes, start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working. This lets you check your electrical connection at the same time.
During your trip, check occasionally to be sure that the load is secure, and that the lamps and any trailer brakes are still working.
Following Distance
Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require
heavy braking and sudden turns.
Passing
You???ll need more passing distance up ahead when you???re towing a trailer. And, because you???re a good deal longer, you???ll need to go much farther beyond the passed vehicle before you can return to your lane.
Backing Up
Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, just move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you.
Making Turns
Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. Your vehicle could be damaged. Avoid making very sharp turns while trailering.
When you???re turning with a trailer, make wider turns than normal. Do this so your trailer won???t strike soft shoulders, curbs, road signs, trees or other objects. Avoid jerky or sudden maneuvers. Signal well in advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle has to have extra wiring and a
The arrows on your instrument panel will ???ash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also ???ash, telling other drivers you???re about to turn, change lanes or stop.
When towing a trailer, the arrows on your instrument panel will ???ash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers behind you are seeing your signal when they are not. It???s important to check occasionally to be sure the trailer bulbs are still working.
Driving On Grades
Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don???t shift down, you might have to use your brakes so much that they would get hot and no longer work well.
When towing at high altitude on steep uphill grades, consider the following: Engine coolant will boil at a lower temperature than at normal altitudes. If you turn your engine off immediately after towing at high altitude on steep uphill grades, your vehicle may show signs similar to engine overheating. To avoid this, let the engine run while parked (preferably on level ground) with the automatic transmission in PARK (P) (or the manual transmission out of gear and the parking brake applied) for a few minutes before turning the engine off. If you do get the overheat warning, see Engine Overheating
on page
Parking on Hills
{CAUTION:
You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged.
But if you ever have to park your rig on a hill, here???s how to do it:
1.Apply your regular brakes, but don???t shift into PARK (P) yet, or into gear for a manual transmission. When parking uphill, turn your wheels away from the curb. When parking downhill, turn your wheels into the curb.
2.Have someone place chocks under the trailer wheels.
3.When the wheel chocks are in place, release the regular brakes until the chocks absorb the load.
4.Reapply the regular brakes. Then apply your parking brake, and then shift into PARK (P), or REVERSE (R) for a manual transmission. See
Parking Brake on page
5.If you have a
6.Release the regular brakes.
When You Are Ready to Leave After Parking on a Hill
1.Apply your regular brakes and hold the pedal down while you:
???start your engine,
???shift into a gear, and
???release the parking brake.
2.Let up on the brake pedal.
3.Drive slowly until the trailer is clear of the chocks.
4.Stop and have someone pick up and store the chocks.
Maintenance When Trailer Towing
Your vehicle will need service more often when you???re pulling a trailer. See Scheduled Maintenance on
page
Check periodically to see that all hitch nuts and bolts are tight.
Section 5 Service and Appearance Care
Section 5 Service and Appearance Care
Service
Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer
for all your service needs. You will get genuine GM parts and
We hope you will want to keep your GM vehicle all GM. Genuine GM parts have one of these marks:
California Proposition 65 Warning
Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ???uids, and some component wear
Doing Your Own Service Work
If you want to do some of your own service work, you will want to use the proper service manual. It tells
you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on
page
Your vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your
You should keep a record with all parts receipts and list the mileage and the date of any service work you perform. See Maintenance Record on page
{CAUTION:
You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it.
???Be sure you have sufficient knowledge, experience, the proper replacement parts and tools before you attempt any vehicle maintenance task.
???Be sure to use the proper nuts, bolts and other fasteners. English and metric fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.
Adding Equipment to the Outside of Your Vehicle
Things you might add to the outside of your vehicle can affect the air???ow around it. This may cause wind
noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Fuel
Use of the recommended fuel is an important part of the proper maintenance of your vehicle.
Gasoline Octane
Use regular unleaded gasoline with a posted octane of 87 or higher. If the octane is less than 87, you may get a heavy knocking noise when you drive. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. Otherwise, you might damage your engine. A little pinging noise when you accelerate or drive uphill is considered normal. This does not indicate a problem exists or that a
Gasoline Speci???cations
It is recommended that gasoline meet speci???cations which were developed by automobile manufacturers around the world and contained in the
California Fuel
If your vehicle is certi???ed to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California speci???cations. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal speci???cations, but emission control system performance may be affected. The malfunction indicator lamp may turn on and your vehicle may fail a
Malfunction Indicator Lamp on page
Additives
To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. In most cases, you should not have to add anything to your fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. General Motors recommends that you buy gasolines that are advertised to help keep fuel injectors and intake valves clean. If your vehicle experiences problems due to dirty injectors or valves, try a different brand of gasoline. Also, your GM dealer has additives that will help correct and prevent most
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors recommends that you use these gasolines, particularly if they comply with the speci???cations described earlier.
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty.
Some gasolines that are not reformulated for low emissions may contain an
gasoline whether the fuel contains MMT. General Motors does not recommend the use of such gasolines.
Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system may be affected. The malfunction indicator lamp
may turn on. If this occurs, return to your authorized GM dealer for service.
Fuels in Foreign Countries
If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to ???nd. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not
be covered by your warranty.
To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.
Filling Your Tank
{CAUTION:
Fuel vapor burns violently and a fuel ???re can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, ???ames and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling your vehicle ??? this is against the law in some places. Keep children away from the fuel pump; never let children pump fuel.
The tethered fuel cap is located behind a hinged fuel door on the driver???s side of the vehicle.
To remove the fuel cap, turn it slowly to the left (counterclockwise).
While refueling, hang the tethered fuel cap from the hook on the fuel door.
{CAUTION:
If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or over???ll the tank and wait a few seconds after you have ???nished pumping before removing the nozzle. Clean fuel
from painted surfaces as soon as possible. See
Washing Your Vehicle on page
When replacing the fuel cap, turn it to the right (clockwise) until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This
would allow fuel to evaporate into the atmosphere. If the fuel cap is not properly installed, FUEL CAP will
appear on the DIC and the check engine light will be lit on the instrument panel cluster. See DIC Warnings and Messages on page
{CAUTION:
If a ???re starts while you are refueling, do not remove the nozzle. Shut off the ???ow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately.
Notice: If you need a new fuel cap, be sure to get the right type. Your dealer can get one for you. If you get the wrong type, it may not ???t properly. This may cause your malfunction indicator lamp to light and may damage your fuel tank and emissions system. See Malfunction Indicator Lamp on page
Filling a Portable Fuel Container
{CAUTION:
Never ???ll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor.
You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others:
???Dispense gasoline only into approved containers.
???Do not ???ll a container while it is inside a vehicle, in a vehicle???s trunk, pickup bed or on any surface other than the ground.
???Bring the ???ll nozzle in contact with the inside of the ???ll opening before operating the nozzle. Contact should be maintained until the ???lling is complete.
???Do not smoke while pumping gasoline.
Checking Things Under
the Hood
{CAUTION:
Things that burn can get on hot engine parts and start a ???re. These include liquids like fuel, oil, coolant, brake ???uid, windshield washer and other ???uids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine.
Hood Release
To open the hood, do the following:
1. Pull the handle with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel.
2.Release the secondary latch on the hood. It is located below the front center of the hood.
3.Lift the hood.
4.Release the hood prop from its retainer and put the hood prop into the slot in the hood.
Before closing the hood, be sure all the ???ller caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the hood and return the prop to its retainer. Lower the hood 10 to 12 inches (25 to 30 cm) above the vehicle and release it to latch fully. Check to make sure the hood is closed and repeat the procedure if necessary.
Engine Compartment Overview
When you open the hood on the 2.8 L engine (3.5 L engine similar), you will see the following:
A.Windshield Washer Fluid. See ???Adding Washer Fluid??? under Windshield Washer Fluid on page
B.Coolant Recovery Tank. See Engine Coolant on page
C.Power Steering Fluid Reservoir (low in engine compartment). See Power Steering Fluid on page
D.Transmission Fluid Dipstick. See Automatic Transmission Fluid on page
E.Engine Oil Dipstick. See ???Checking Engine Oil??? under Engine Oil on page
F.Brake Fluid Reservoir. See ???Brake Fluid??? under
Brakes on page
G.Battery. See Battery on page
H.Hydraulic Clutch Fluid Reservoir (If Equipped). See
Hydraulic Clutch on page
I.Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page
J.Engine Oil Fill Cap. See ???When to Add Engine Oil??? under Engine Oil on page
K.Radiator Pressure Cap. See Cooling System on page
L.Remote Negative (???) Terminal. See Jump Starting on page
M.Remote Positive (+) Terminal. See Jump Starting on page
N.Engine Compartment Fuse Block. See Engine Compartment Fuse Block on page
Engine Oil
Checking Engine Oil
It is a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. See
Engine Compartment Overview on page
1.Turn off the engine and give the oil several minutes to drain back into the oil pan. If you do not do this, the oil dipstick might not show the actual level.
2.Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.
When to Add Engine Oil
If the oil is at or below the
you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speci???cations on page
Notice: Do not add too much oil. If your engine has so much oil that the oil level gets above the
See Engine Compartment Overview on page
engine oil ???ll cap.
Be sure to add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when you are through.
What Kind of Engine Oil to Use
Look for two things:
???GM6094M
Your vehicle???s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M.
???SAE
As shown in the viscosity chart, SAE
These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE
Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certi???ed by the American Petroleum Institute (API).
You should look for this information on the oil container, and use only those oils that are identi???ed as meeting GM Standard GM6094M and have the starburst symbol on the front of the oil container.
Notice: Use only engine oil identi???ed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certi???ed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty.
GM Goodwrench?? oil meets all the requirements for your vehicle.
If you are in an area of extreme cold, where the temperature falls below ???20??F ( ???29??C), it is recommended that you use either an SAE
Engine Oil Additives
Do not add anything to your oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you will need for good performance and engine protection.
Engine Oil Life System
When to Change Engine Oil
Your vehicle has a computer system that lets you know when to change the engine oil and ???lter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably. For the oil life system to work properly, you must reset the system every time the oil is changed.
When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE OIL message will come on. See DIC Warnings and Messages on page
If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed.
How to Reset the Engine Oil Life System
The Engine Oil Life System calculates when to change your engine oil and ???lter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL message being turned on, reset the system.
To reset the Engine Oil Life system, do the following:
1.With the engine off, turn the ignition to ON.
2.Press and release the reset button in the DIC until the OIL LIFE message is displayed.
3.Once the alternating OIL LIFE and RESET messages appear on the DIC display, press and hold the reset stem until several beeps sound. This con???rms that the oil life system has been reset.
4.Turn the key to LOCK.
If the CHANGE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer???s warnings about the use and disposal of oil products.
Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ???lter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Instead, recycle it by taking it to a place that collects used oil. If you have a problem properly disposing of your used oil, ask your dealer, a service station or a local recycling center for help.
Engine Air Cleaner/Filter
The engine air cleaner/???lter is located in the engine compartment on the passenger???s side of the vehicle. See Engine Compartment Overview on page
When to Inspect the Engine Air Cleaner/Filter
Inspect the air cleaner/???lter at the Maintenance II intervals and replace it at the ???rst oil change after 50,000 miles (83 000 km). See Scheduled Maintenance on page
in dusty/dirty conditions, inspect the ???lter at each engine oil change.
How to Inspect the Engine Air Cleaner/Filter
To inspect or replace the engine air cleaner/???lter, do the following:
1.Unfasten the clips that hold the cover on and remove the cover.
2.Lift out the engine air cleaner/???lter.
3.Inspect or replace the air ???lter. See Normal Maintenance Replacement Parts on page
4.Reinstall the engine air cleaner/???lter cover. Fasten the clips to hold the cover in place.
{CAUTION:
Operating the engine with the air cleaner/???lter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop ???ame if the engine back???res. If it is not there and the engine back???res, you could
be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/???lter off.
Notice: If the air cleaner/???lter is off, a back???re can cause a damaging engine ???re. And, dirt can
easily get into your engine, which will damage it. Always have the air cleaner/???lter in place when you are driving.
Automatic Transmission Fluid
When to Check and Change
A good time to check your automatic transmission ???uid level is when the engine oil is changed.
Change both the ???uid and ???lter every 50,000 miles
(83 000 km) if the vehicle is mainly driven under one or more of these conditions:
???In heavy city traffic where the outside temperature regularly reaches 90??F (32??C) or higher.
???In hilly or mountainous terrain.
???When doing frequent trailer towing.
???Uses such as found in taxi, police or delivery service.
If you do not use your vehicle under any of these conditions, change the ???uid and ???lter every 100,000 miles (166 000 km).
See Scheduled Maintenance on page
How to Check
Because this operation can be a little difficult, you may choose to have this done at the dealership service department.
If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.
Notice: Too much or too little ???uid can damage your transmission. Too little ???uid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission ???uid.
Wait at least 30 minutes before checking the transmission ???uid level if you have been driving:
???When outside temperatures are above 90??F (32??C).
???At high speed for quite a while.
???In heavy traffic ??? especially in hot weather.
???While pulling a trailer.
To get the right reading, the ???uid should be at normal operating temperature, which is 180??F to 200??F (82??C to 93??C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are above 50??F (10??C). If it is colder than 50??F (10??C), drive
the vehicle in THIRD (3) until the engine temperature gage moves and then remains steady for 10 minutes.
A cold ???uid check can be made after the vehicle
has been sitting for eight hours or more with the engine off, but this is used only as a reference. Let the
engine run at idle for ???ve minutes if outside temperatures are 50??F (10??C) or more. If it is colder than 50??F (10??C), you may have to idle the engine longer. Should the ???uid level be low during this cold check, you must check the ???uid hot before adding ???uid. Checking the ???uid hot will give you a more accurate reading of the ???uid level.
Checking the Fluid Level
Prepare your vehicle as follows:
???Park your vehicle on a level place. Keep the engine running.
???With the parking brake applied, place the shift lever in PARK (P).
???With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P).
???Let the engine run at idle for three minutes or more.
Then, without shutting off the engine, follow these steps:
The transmission dipstick handle has this symbol on it.
The transmission dipstick is located toward the rear of the engine compartment on the passenger???s side of the vehicle. See Engine Compartment Overview
on page
1.Flip the handle up and then pull out the dipstick and wipe it with a clean rag or paper towel.
2.Push it back in all the way, wait three seconds and then pull it back out again.
3.Check both sides of the dipstick, and read the lower level. The ???uid level must be in the COLD area, below the
4.If the ???uid level is in the acceptable range, push the dipstick back in all the way; then ???ip the handle down to lock the dipstick in place.
How to Add Fluid
Refer to the Maintenance Schedule to determine what kind of transmission ???uid to use. See Recommended Fluids and Lubricants on page
Add ???uid only after checking the transmission ???uid while it is hot. A cold check is used only as a reference. If the ???uid level is low, add only enough of the proper ???uid to bring the level up to the HOT area for a hot check. It does not take much ???uid, generally less than
one pint (0.5 L). Do not over???ll.
Notice: Use of automatic transmission ???uid labeled other than DEXRON??
???After adding ???uid, recheck the ???uid level as described under ???How to Check,??? earlier in this section.
???When the correct ???uid level is obtained, push the dipstick back in all the way; then ???ip the handle down to lock the dipstick in place.
Manual Transmission Fluid
When to Check
A good time to have it checked is when the engine oil is changed. However, the ???uid in your manual transmission does not require changing.
How to Check
Because this operation can be a little difficult, you may choose to have this done at your GM dealership service department.
If you do it yourself, be sure to follow all the instructions here, or you could get a false reading.
Notice: Too much or too little ???uid can damage your transmission. Too little ???uid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission ???uid.
Check the ???uid level only when your engine is off, the vehicle is parked on a level place and the transmission is cool enough for you to rest your ???ngers on the transmission case.
Then, follow these steps:
1.Remove the ???ller plug.
2.Check that the lubricant level is up to the bottom of the ???ller plug hole.
3.If the ???uid level is good, install the plug and be sure it is fully seated. If the ???uid level is low, add more ???uid as described in the next steps.
How to Add Fluid
Here is how to add ???uid. Refer to the Maintenance Schedule to determine what kind of ???uid to use. See
Recommended Fluids and Lubricants on page
1.Remove the ???ller plug.
2.Add ???uid at the ???ller plug hole. Add only enough ???uid to bring the ???uid level up to the bottom of the ???ller plug hole.
3.Install the ???ller plug. Be sure the plug is fully seated.
Hydraulic Clutch
The hydraulic clutch linkage in your vehicle is
The hydraulic clutch ???uid reservoir cap has this symbol on it. See Engine Compartment Overview on page
It is not necessary to regularly check clutch ???uid unless you suspect there is a leak in the system. Adding
???uid will not correct a leak.
A ???uid loss in this system could indicate a problem. Have the system inspected and repaired.
When to Check and What to Use
Refer to the Maintenance Schedule to determine how often you should check the ???uid level in your clutch master cylinder reservoir and for the proper ???uid. See
Recommended Fluids and Lubricants on page
How to Check and Add Fluid
The proper ???uid should be added if the level does not reach the bottom of the diaphragm when it is in place in the reservoir. See the instructions on the reservoir cap.
Engine Coolant
The cooling system in your vehicle is ???lled with
only
The following explains your cooling system and how to add coolant when it is low. If you have a problem
with engine overheating, see Engine Overheating on page
A 50/50 mixture of clean, drinkable water and
???Give freezing protection down to ???34??F ( ???37??C).
???Give boiling protection up to 265??F (129??C).
???Protect against rust and corrosion.
???Help keep the proper engine temperature.
???Let the warning lights and gages work as they should.
Notice: Using coolant other than
What to Use
Use a mixture of
{CAUTION:
Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle???s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ???re and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and the proper coolant.
Notice: If you use an improper coolant mixture, your engine could overheat and be badly damaged. The repair cost would not be covered by your warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core and other parts.
Notice: If you use the proper coolant, you do not have to add extra inhibitors or additives which claim to improve the system. These can be harmful.
Checking Coolant
The coolant recovery tank is located toward the rear of the engine compartment on the passenger???s side of the vehicle. See Engine Compartment Overview on page
The vehicle must be on a level surface. When your engine is cold, the coolant level should be at FULL COLD, or a little higher. When your engine is warm, the level could be above the FULL COLD level.
Adding Coolant
If you need more coolant, add the proper
{CAUTION:
Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost never have to add coolant at the radiator. Never turn the radiator pressure
cap ??? even a little ??? when the engine and radiator are hot.
Add coolant mixture at the recovery tank, but be careful not to spill it.
{CAUTION:
You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.
Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see Cooling System on page
Radiator Pressure Cap
Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.
See Engine Compartment Overview on page
Engine Overheating
You will ???nd a coolant temperature gage on your vehicle???s instrument panel. See Engine Coolant Temperature Gage on page
Your air conditioning may stop working if your engine is too hot. This is normal and helps cool the engine.
If Steam Is Coming From Your Engine
{CAUTION:
Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
If you keep driving when your engine is overheated, the liquids in it can catch ???re. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool.
Notice: If your engine catches ???re because you keep driving with no coolant, your vehicle can
be badly damaged. The costly repairs would not be covered by your warranty.
If No Steam Is Coming From Your
Engine
If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you:
???Climb a long hill on a hot day.
???Stop after
???Idle for long periods in traffic.
???Tow a trailer. See ???Driving on Grades??? under
Towing a Trailer on page
If you get the overheat warning with no sign of steam, try this for a minute or so:
1.In heavy traffic, let the engine idle in NEUTRAL while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL and let the engine idle.
2.Turn off the air conditioning.
3.Turn on your heater to full hot at the highest fan speed and open the windows as necessary.
If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning does not come back on, you can drive normally.
If the warning continues, pull over, stop, and park your vehicle right away.
If there is still no sign of steam, idle the engine for three minutes while you are parked. Push down the accelerator until the engine speed is about twice as fast as normal idle speed for at least three minutes while you are parked. If you still have the warning, turn off the engine and get everyone out of the vehicle until it cools down.
You may decide not to lift the hood but to get service help right away.
Cooling System
When you decide it is safe to lift the hood, here is what you will see:
A.Coolant Recovery Tank
B.Engine Cooling Fan
C.Radiator Pressure Cap
If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface.
When the engine is cold, the coolant level should be at least up to the FULL COLD mark. If it is not, you
may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
{CAUTION:
Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned.
Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ???re, and you could be burned. Get any leak ???xed before you drive the vehicle.
If there seems to be no leak, start the engine again. The engine cooling fan speed should increase when idle speed is doubled by pushing the accelerator pedal down. If it does not, your vehicle needs service. Turn off the engine.
Notice: Engine damage from running your engine without coolant is not covered by your warranty.
Notice: Using coolant other than
How to Add Coolant to the Coolant Recovery Tank
If you have not found a problem yet, but the coolant level is not at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and
{CAUTION:
Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle???s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ???re and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and
Notice: In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture.
{CAUTION:
You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.
When the coolant in the coolant recovery tank is at the FULL COLD mark, start your vehicle.
If the overheat warning continues, there is one more thing you can try. You can add the proper mixture directly to the radiator, but be sure the cooling system is cool before you do it.
{CAUTION:
Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap ??? even a little ??? they can come
out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot. Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap.
How to Add Coolant to the Radiator
1.You can remove the radiator pressure cap when the cooling system, including the upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn.
If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left.
2.Then keep turning the cap to remove it.
3.Fill the radiator with the proper
neck. See Engine Coolant on page
4.Then ???ll the coolant recovery tank to the FULL COLD mark.
5.Reinstall the cap on the coolant recovery tank, but leave the radiator pressure cap off.
6.Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
7.By this time, the coolant level inside the radiator
???ller neck may be lower. If the level is lower, add more of the proper
the base of the ???ller neck.
Then replace the pressure cap. At any time during this procedure if coolant begins to ???ow out of
the ???ller neck, reinstall the pressure cap. Be sure to secure it tightly.
Engine Fan Noise
This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the clutch is not engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing and/or high outside temperatures, the fan speed increases when the clutch engages.
So you may hear an increase in fan noise. This is normal and should not be mistaken as the
transmission slipping or making extra shifts. It is merely the cooling system functioning properly. The fan will slow down when additional cooling is not required and the clutch disengages.
You may also hear this fan noise when you start the engine. It will go away as the fan clutch disengages.
Power Steering Fluid
The power steering ???uid reservoir is located near the front of the engine compartment, behind the radiator. See Engine Compartment Overview on page
When to Check Power Steering Fluid
It is not necessary to regularly check power steering ???uid unless you suspect there is a leak in the system or
you hear an unusual noise. A ???uid loss in this system could indicate a problem. Have the system inspected and repaired.
How to Check Power Steering Fluid
1.Turn the key off and let the engine compartment cool down.
2.Wipe the cap and the top of the reservoir clean.
3.Unscrew the cap and wipe the dipstick with a clean rag.
4.Replace the cap and completely tighten it.
5.Then remove the cap again and look at the ???uid level on the dipstick.
The level should be between the ADD and FULL marks. If necessary, add only enough ???uid to bring the level
up to the proper range.
What to Use
To determine what kind of ???uid to use, see
Recommended Fluids and Lubricants on page
Windshield Washer Fluid
What to Use
When you need windshield washer ???uid, be sure to read the manufacturer???s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ???uid that has sufficient protection against freezing.
Adding Washer Fluid
Open the cap with the washer symbol on it. Add washer ???uid until the tank is full. See Engine
Compartment Overview on page
Notice:
???When using concentrated washer ???uid, follow the manufacturer???s instructions for adding water.
???Do not mix water with
???Fill your washer ???uid tank only
???Do not use engine coolant (antifreeze) in your windshield washer. It can damage your washer system and paint.
Brakes
Brake Fluid
Your brake master cylinder reservoir is ???lled with
Engine Compartment Overview on page
There are only two reasons why the brake ???uid level in the reservoir might go down. The ???rst is that the
brake ???uid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the ???uid level goes back up. The other reason is
that ???uid is leaking out of the brake system. If it is, you should have your brake system ???xed, since a leak means that sooner or later your brakes will not work well, or will not work at all.
So, it is not a good idea to top off your brake ???uid. Adding brake ???uid will not correct a leak. If you add ???uid when your linings are worn, then you will have too much ???uid when you get new brake linings. You should add or remove brake ???uid, as necessary, only when work is done on the brake hydraulic system.
{CAUTION:
If you have too much brake ???uid, it can spill on the engine. The ???uid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake ???uid only when work is done on the brake hydraulic system. See ???Checking Brake Fluid??? in this section.
Refer to the Maintenance Schedule to determine when to check your brake ???uid. See Scheduled Maintenance on page
Checking Brake Fluid
You can check the brake ???uid without taking off the cap.
Just look at the brake ???uid reservoir. The ???uid level should be above MIN. If it is not have your brake system checked to see if there is a leak.
After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
What to Add
When you do need brake ???uid, use only
Always clean the brake ???uid reservoir cap and the area around the cap before removing it. This will help
keep dirt from entering the reservoir.
{CAUTION:
With the wrong kind of ???uid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake ???uid.
Notice:
???Using the wrong ???uid can badly damage brake system parts. For example, just a few drops of
???If you spill brake ???uid on your vehicle???s painted surfaces, the paint ???nish can be damaged. Be careful not to spill brake ???uid on your vehicle. If you do, wash it off immediately. See Appearance Care on page
Brake Wear
Your vehicle has front disc brakes and rear drum brakes.
Disc brake pads have
are worn and new pads are needed. The sound
may come and go or be heard all the time your vehicle is moving, except when you are pushing on the
brake pedal ???rmly.
{CAUTION:
The brake wear warning sound means that soon your brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.
Notice: Continuing to drive with
Some driving conditions or climates may cause a brake squeal when the brakes are ???rst applied or lightly applied. This does not mean something is wrong with your brakes.
Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque speci???cations.
Rear drum brakes do not have wear indicators, but if you ever hear a rear brake rubbing noise, have the rear brake linings inspected immediately. Also, the rear brake drums should be removed and inspected each time the tires are removed for rotation or changing. When you have the front brake pads replaced, have the rear brakes inspected, too.
Brake linings should always be replaced as complete axle sets.
Brake Pedal Travel
See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble.
Brake Adjustment
Every time you make a brake stop, your brakes adjust for wear.
Replacing Brake System Parts
The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with
wear down and you need new ones put in ??? be sure you get new approved GM replacement parts. If you do not, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change ??? for the worse. The braking performance you have come to expect can change
in many other ways if someone puts in the wrong replacement brake parts.
Battery
Your vehicle has a maintenance free battery. When it is time for a new battery, get one that has the replacement number shown on the original battery???s label. We recommend an ACDelco?? replacement battery. See
Engine Compartment Overview on page
Warning: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Vehicle Storage
If you are not going to drive your vehicle for 25 days or more, remove the black, negative (???) cable from the battery. This will help keep your battery from running down.
{CAUTION:
Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on
page
Also, for your audio system, see
Jump Starting
If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.
{CAUTION:
Batteries can hurt you. They can be dangerous because:
???They contain acid that can burn you.
???They contain gas that can explode or ignite.
???They contain enough electricity to burn you.
If you do not follow these steps exactly, some or all of these things can hurt you.
Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty.
Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle.
1.Check the other vehicle. It must have a
Notice: If the other vehicle???s system is not a
2.Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding
could damage the electrical systems.
To avoid the possibility of the vehicles rolling, set the parking brake ???rmly on both vehicles involved in the jump start procedure. Put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before setting the parking brake. If you have a
Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and other accessories when jump starting your vehicle.
3.Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets. Turn off
the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!
4.Open the hoods and locate the positive (+) and negative (???) terminal locations on the other
vehicle. Your vehicle has a remote positive (+) and a remote negative (???) jump starting terminal.
See Engine Compartment Overview on page
{CAUTION:
Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ???ashlight if you need more light.
Be sure the batteries have enough water. You do not need to add water to the ACDelco?? battery (or batteries) installed in your new vehicle. But if a battery has ???ller caps, be sure the right amount of ???uid is there. If it is low, add water to take care of that ???rst. If you do not, explosive gas could be present.
Battery ???uid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ???ush the place with water and get medical help immediately.
{CAUTION:
Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.
5.Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too.
Before you connect the cables, here are some basic things you should know. Positive (+) will go to
positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (???) will go to a heavy,
unpainted metal engine part or to a remote negative (???) terminal if the vehicle has one.
Do not connect positive (+) to negative (???) or you will get a short that would damage the battery
and maybe other parts too. And do not connect the negative (???) cable to the negative (???) terminal on the dead battery because this can cause sparks.
6.Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote
positive (+) terminal if the vehicle has one.
7.Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
8.Now connect the black negative (???) cable to the negative (???) terminal of the good battery. Use a remote negative (???) terminal if the vehicle has one.
Do not let the other end touch anything until the next step. The other end of the negative (???) cable
does not go to the dead battery. It goes to a heavy,
unpainted metal engine part, or to a remote negative (???) terminal on the vehicle with the dead battery.
9.Connect the other end of the negative (???) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance
of sparks getting back to the battery is much less. Your vehicle has a remote negative (???) terminal for this purpose. See Engine Compartment
Overview on page
10.Now start the vehicle with the good battery and run the engine for a while.
11.Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service.
Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Jumper Cable Removal
A.Heavy, Unpainted Metal Engine Part
B.Good Battery
C.Dead Battery
To disconnect the jumper cables from both vehicles, do the following:
1.Disconnect the black negative (???) cable from the vehicle that had the dead battery.
2.Disconnect the black negative (???) cable from the vehicle with the good battery.
3.Disconnect the red positive (+) cable from the vehicle with the good battery.
4.Disconnect the red positive (+) cable from the other vehicle.
Rear Axle
When to Check and Change Lubricant
It is not necessary to regularly check rear axle ???uid unless you suspect there is a leak or you hear an unusual noise. A ???uid loss could indicate a problem. Have it inspected and repaired.
How to Check Lubricant
To get an accurate reading, the vehicle should be on a level surface.
If the level is below the bottom of the ???ller plug hole, located on the rear axle, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ???ller plug hole.
What to Use
See Recommended Fluids and Lubricants on page
Lubricant checks in this section apply to this vehicle. There are two additional systems that need lubrication.
Transfer Case
When to Check Lubricant
Refer to the Maintenance Schedule to determine how often to check the lubricant. See Additional Required Services on page
How to Check Lubricant
To get an accurate reading, the vehicle should be on a level surface.
If the level is below the bottom of the ???ller plug hole, located on the transfer case, you???ll need to add some lubricant. Remove the plug and add enough lubricant to raise the level to the bottom of the ???ller plug hole. Use care not to overtighten the plug.
What to Use
Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page
Front Axle
When to Check and Change Lubricant
It is not necessary to regularly check your front axle ???uid unless you suspect there is a leak or you hear an unusual noise. A ???uid loss could indicate a problem. Have it inspected and repaired.
How to Check Lubricant
To get an accurate reading, the vehicle should be on a level surface.
If the level is below the bottom of the ???ller plug hole, located on the front axle, you may need to add some lubricant.
When the differential is cold, add enough lubricant to raise the level to 1/2 inch (12 mm) below the ???ller plug hole.
When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the ???ller plug hole.
What to Use
See Recommended Fluids and Lubricants on page
Bulb Replacement
For the proper types of bulbs to use, see Replacement Bulbs on page
For any bulb changing procedure not listed in this section, contact your dealer???s service department.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
Headlamps
Composite Headlamp System
A.
B.
To replace the bulbs, do the following:
1.Open and support the hood. See Hood Release on page
2.Access the bulb/sockets from the engine compartment.
3.Turn the bulb socket counterclockwise and pull it straight out of the headlamp housing.
4.Unplug the electrical connector from the old bulb.
5.Plug in the electrical connector to the new bulb. Use care not to touch the new bulb with your bare hand, anything damp or oily.
6.Place the connector with the new bulb into the headlamp housing and turn it clockwise until it is tight.
Sealed Beam Headlamps
To replace the headlamp capsule, do the following:
1.Remove the four retainer screws and the retainer.
2.Pull the headlamp capsule toward you and unplug the electrical connector from it.
3.Remove the old headlamp capsule.
4.Plug the electrical connector into the new headlamp capsule.
5.Reverse Steps 1 and 2 to reinstall the headlamp.
Front Turn Signal, Sidemarker and
Daytime Running Lamps
1.Remove the turn signal/parking lamp/daytime running lamp (DRL) assembly by pressing on the release clip on the outboard side of the housing and pulling the outboard end of the lamp toward you.
2.Pull the inboard side of the lamp out from the small post in the grille.
3.Turn the bulb socket counterclockwise and remove it from the lamp housing.
4.Remove the old bulb from the bulb socket.
5.Insert the new bulb into the bulb socket.
6.Insert the bulb socket into the lamp housing and turn it clockwise until it is tight.
7.Place the inboard end of the turn signal/parking lamp/DRL housing over the small post in the grille.
8.Align the release clip of the lamp assembly with the square opening in the grille.
9.Push the outboard side of the lamp assembly in, until the release clip snaps into place.
Center
1. Remove the screws and lift off the lamp assembly.
2.Turn the bulb socket counterclockwise and remove it from the housing.
3.Pull the bulb straight out of the socket.
4.Insert the new bulb into the socket and press it in until tight.
5.Insert the bulb socket into the housing and turn until tight.
6.Reinstall the lamp assembly and tighten the screws.
Taillamps, Turn Signal, Stoplamps
and
A. Stoplamp/Taillamp
B. Turn Signal
C.
1. Open the tailgate. See Tailgate on page
2. Remove the two rear lamp assembly screws near the tailgate latch.
3.Pull out the lamp assembly.
4.Turn the bulb socket counterclockwise to remove it from the taillamp housing.
5.Pull the old bulb straight out from the socket.
6.Press a new bulb into the socket and turn the socket clockwise into the taillamp housing until it is tight.
7.Reinstall the rear lamp assembly and tighten the screws.
8.Close the tailgate.
Replacement Bulbs
For replacement bulbs not listed here, contact your dealer.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected at least twice a year for wear and cracking. See ???Wiper Blade Check??? under Scheduled Maintenance on page
Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on
page
Notice: Allowing the wiper blade arm to touch the windshield when no wiper blade is installed
could damage the windshield. Any damage that occurs would not be covered by your warranty. Do not allow the wiper blade arm to touch the windshield.
1.To remove the old wiper blades, lift the wiper arm until it locks into a vertical position.
2.Press down on the blade assembly pivot locking tab. Pull down on the blade assembly to release it from the wiper arm hook.
3.Remove the insert from the blade assembly. The insert has two notches at one end that are locked by bottom claws of the blade assembly. At the notched end, pull the insert from the blade assembly.
4.To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted.
5.Be sure that the notches are locked by the bottom claws. Make sure that all other claws are properly locked on both sides of the insert slots.
A.Claw in Notch
B.Correct Installation
C.Incorrect Installation
6.Put the blade assembly pivot in the wiper arm hook. Pull up until the pivot locking tab locks in the hook slot.
7.Carefully lower the wiper arm and blade assembly onto the windshield.
Tires
Your new vehicle comes with
{CAUTION:
Poorly maintained and improperly used tires are dangerous.
???Overloading your tires can cause overheating as a result of too much friction. You could have an
CAUTION: (Continued)
CAUTION: (Continued)
???Underin???ated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. See In???ation - Tire Pressure on page
???Overin???ated tires are more likely to be cut, punctured or broken by a sudden
impact ??? such as when you hit a pothole. Keep tires at the recommended pressure.
???Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.
Tire Sidewall Labelling
Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.
Passenger Vehicle Tire Example
(A) Tire Size: The tire size is a combination of letters and numbers used to de???ne a particular tire???s width, height, aspect ratio, construction type and service description. See the ???Tire Size??? illustration later in this section for more detail.
(B)TPC Spec (Tire Performance Criteria Speci???cation): Original equipment tires designed to GM???s speci???c tire performance criteria have a TPC speci???cation code molded onto the sidewall. GM???s TPC speci???cations meet or exceed all federal safety guidelines.
(C)DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.
(D)Tire Identi???cation Number (TIN): The letters and numbers following DOT code are the Tire Identi???cation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
(E)Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.
(F)Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information see Uniform Tire Quality Grading on page
(G)Maximum Cold In???ation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
Compact Spare Tire Example
(A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven
at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire
has lost air and gone ???at. See ???Compact Spare Tire??? under Spare Tire on page
(B)Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.
(C)Tire Identi???cation Number (TIN): The Tire Identi???cation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both
sides of the tire, although only one side may have the date of manufacture.
(D)Maximum Cold In???ation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
(E)Tire In???ation: The temporary use tire or compact spare tire should be in???ated to 60 psi (420 kPa). For more information on tire pressure and in???ation see
In???ation - Tire Pressure on page
(F)Tire Size: A combination of letters and numbers de???ne a tire???s width, height, aspect ratio, construction type and service description. The letter T as the
???rst character in the tire size means the tire is for temporary use only.
(G)TPC Spec (Tire Performance Criteria Speci???cation): Original equipment tires designed to GM???s speci???c tire performance criteria have a TPC speci???cation code molded onto the sidewall. GM???s TPC speci???cations meet or exceed all federal safety guidelines.
