Network Camera

VB-C500D

Start Guide

Please read carefully this Start Guide and the Operation Guide Especially be sure to read "Safety Precautions" before using the network camera. Keep this guide in a readily accessible location for future reference.

Introduction

Thank you for purchasing Canon Network Camera VB-C500D (hereafter referred to as VB-C500D).

This Start Guide describes how to set up and install the VB-C500D. The detailed procedures for using the VB-C500D are explained in the Operation Guide provided on the Setup CD-ROM. Read these guides carefully before using the VB-C500D to ensure that you make the best possible use of this product. Also, be sure to read "Safety Precautions" in this guide.

For the latest information on this product (firmware, bundled software, operation manuals, operating environment, etc.), visit our website.

Disclaimer

Canon Inc. shall not be responsible for any financial losses that may be incurred as a result of the loss of recorded information or images, regardless of the internal or external cause of the loss.

Copyright

Videos, images or sounds recorded with your VB-C500D may not be utilized or published, without consent of copyright holders, if any, except in such a way as permitted for personal use under the relevant copyright law.

Notes

1.All rights reserved.

2.The contents of this guide are subject to change without any prior notice.

3.This document has been prepared with utmost attention to accuracy. If you have any comment, however, please contact the Customer Service Center indicated on the back cover.

4.Canon shall assume no liability for any outcome of using this product, regardless of Items 2 and 3 above.

Notes on privacy and publicity rights regarding the utilization of video/audio

When using the VB-C500D (for video or audio recording), it is the responsibility of the users to take all care to protect privacy and avoid any violation of publicity rights. Canon shall have no liability whatsoever in this regard.

Reference

Please be sure to gain approval of the building management office before installing a camera, if copyrighted architectural structures or copyrighted premises are appear in the frame.

Legal Notice

In some countries or regions, monitoring via a camera is banned by the law or regulation, and the law or regulation depends on the country or region. Before using the VB-C500D, confirm the law or regulation of the country or region where the camera is used.

ii

Introduction

Trademark Notice

Canon and the Canon logo are registered trademarks of Canon Inc.

Microsoft Windows and Microsoft Internet Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.

Windows is legally recognized as the Microsoft Windows Operating System.

Other brands or product names in this guide are trademarks or registered trademarks of their respective companies.

Warning

To reduce the risk of fire or electric shock, do not expose this appliance to rain or

moisture.

Notes on Use of Bundled Software VK-Lite (Disclaimer)

Malfunction, failure of VK-Lite or other factors may cause problems, such as recording failure, recorded data corruption or loss. Canon shall have no liability whatsoever for any loss or damages incurred by the user as a result of such problems.

European Union (and EEA) only.

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or your national laws implementing those Directives.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a

new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE.

Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.

For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

iii

Introduction

MPEG-4

NOTICE ABOUT THE MPEG-4 VISUAL STANDARD: THIS PRODUCT IS LICENSED UNDER

THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON- COMMERCIAL USE OF A CONSUMER TO (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/OR (ii) DECODING MPEG-4

VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-

COMMERCIAL ACTIVITY. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY

OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL,

INTERNAL AND COMMERCIAL USES AND ADDITIONAL LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.

This product is licensed under AT&T patents for the MPEG-4 standard and maybe used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard.

Third Party Software

The product (VB-C500D and bundled VK-Lite Viewer) contains third party software modules. For detail information, please see ReadMe-E.txt on the supplied Setup CD-ROM. Each module???s license conditions are also available in the License folder on the same Setup CD-ROM.

Software under GPL and LGPL

If you would like to obtain the source code under GPL/LGPL, please contact the dealer where you purchased the product, or a sales agent.

iv

Contents

Chapter 1 Before Use

v

Contents

Chapter 2 Initial Setting and Installation of Camera

Chapter 3 Appendix

vi

Checking of Bundled Items

This product comes with the following items. If any item is missing, contact the store where you

purchased the product.

Content of Setup CD-ROM

*Check our website for the latest versions of bundled software and operation manuals.

vii

Checking of Bundled Items

Operation Manuals

The VB-C500D comes with Start Guide (this document) and Operation Guide included in the Setup CD-ROM.

Start Guide (This Document)

The safety precautions to be followed when using the VB-C500D, types of bundled software, operating environment, installation method, initial setting of the camera, installation method, etc., are explained.

Operation Guide (VBC500DOG_E.pdf)

This document explains the basic setup procedure for the VB-C500D, how to use VBAdmin Tools and VB-C500 Viewer, troubleshooting, etc. Items that should be referenced in this document are denoted by "Operation Guide."

Operation Guide is included in the Setup CD-ROM.

Also, a simplified version of recording software VK-Lite ( P. 1-6) is stored in the Setup CD-ROM. The following operation manuals are available:

Setup Guide (VK21SUG_E.pdf)

This document explains the items to note when using VK-Lite, operating environment, system configuration, installation method and setup method.

Administrator???s Manual (VK21AM_E.pdf)

This document explains details on how to use VK-Lite. Be sure to read this document.

Viewer Operation Guide (VK21VOG_E.pdf)

This is an operation guide for the VK-Lite viewer. For the detailed operating procedures of the viewer, refer to Administrator???s Manual.

viii

How to Read This Document

In Start Guide and Operation Guide, screens in Windows Vista are mainly used. Unless otherwise specified, the same screens apply to Windows XP.

Symbols Used for Safety Precautions

In this document, the following symbols are used to indicate important items the user should know to use this product safely. Be sure to observe these items.

Inappropriate handling against the instruction accompanied by this Warning symbol may result in death or injury. Be sure to observe this

precaution to use the product safely.

Inappropriate handling against the instruction accompanied by this Caution symbol may result in injury. Be sure to observe this precaution to

use the product safely.

Inappropriate handling against the instruction accompanied by this

Note symbol may result in property damage. Be sure to observe these precautions.

ix

Safety Precautions

The following explains the items that must be observed when using the VB-C500D.

If they are not observed, injury, death and/or property damage may occur. Read the following information carefully and observe the instructions without fail.

Important Warnings

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

For optional PA-V17 Users in the UK

When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover.

The AC adapter can be connected to VB-C500D from a standard AC power outlet. Please check your instruction manual to make sure that your VB-C500D is compatible with this adapter.

???The socket-outlet should be installed near the equipment and should be easily accessible.

???Unplug the equipment from the wall outlet before cleaning or maintaining.

FDA regulation

This Network Camera has not been evaluated by the Food and Drug Administration (FDA) for use as a medical device. When incorporated into a system with medical applications, FDA regulations may apply. Therefore, please consult your legal advisor to determine whether FDA regulations apply.

x

Safety Precautions

FCC NOTICE

Network Camera, Model Name: VB-C500D

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A. Inc.

One Canon Plaza, Lake Success, NY 11042, U.S.A.

Tel No. (516) 328-5600

Canadian Radio Interference Regulations

This Class B digital apparatus complies with Canadian ICES-003.

xi

Safety Precautions

Precautions for Installation

Warning

Do not install the product in the following places:

???Place receiving strong direct sunlight, near heat generating objects, or subject to high temperature

???Place near fire sources or flammable solvents (alcohol, thinner, etc.)

???Humid or dusty place

???Place subject to lamp black or steam

???Place subject to sea wind

???Narrow, sealed place

Fire or electric shock may result.

Note

For installation or inspection of the VB-C500D, consult/request the store where you purchased the product.

???Wire the VB-C500D power supply, network, or other cables safely and securely according to the relevant regulations such as technical standards for electrical installations.

???When installing the VB-C500D, select a ceiling surface, etc., capable of withstanding the total weight of the camera and all options used (Recessed Mounting Kit), provide sufficient reinforcements and use the bundled safety wire if necessary.

???To prevent injuries and equipment damage due to falling items, periodically check the brackets and screws for rusting and loosening.

???Installation in a place subject to significant vibration is not recommended, because it may cause the equipment to malfunction.

???Do not install the VB-C500D on an unstable or inclined surface.

???Do not carry the product while the LAN cable or other cables still connected to it.

Malfunction may occur.

xii

Safety Precautions

Precautions for Use

Warning

???If smoke, abnormal noise, heat, odor or any other abnormality is detected, immediately stop using the camera and contact your nearest Canon dealer.

Continuing to use the product may result in fire or electric shock.

???Do not disassemble or modify the camera.

???Do not put water or other liquid in the camera or splash or otherwise wet the camera.

???Do not put foreign objects in the camera.

???Do not use sprays of flammable gases near the camera.

???When the camera is not used for a long period, disconnect the LAN cable, external power supply and power connector for AC adapter (optional) from the camera.

Fire or electric shock may result.

Note

???Do not use this camera for medical devices and other systems that affect human life.

Delayed or missing image transmission may occur depending on the PC and network environment, and thus high image transmission accuracy cannot be assured.

Canon will assume no liability for any accident or damage resulting from use of the VB-C500D in the aforementioned devices or systems.

???Do not capture the sun, halogen lamps and other very bright light sources or subjects.

???Do not apply impact on the camera.

Malfunction may result.

This installation should be made by a qualified service person and should confirm to all local codes.

xiii

Safety Precautions

Notes on Use of Motion Detection, Stream for Recording and Bundled Recording Software VK-Lite

Note

???Avoid using Motion Detection, Stream for Recording or recording software VK-Lite for surveillance where very high level of reliability is constantly required.

These are support functions for monitoring. They do not guarantee monitoring with very high accuracy, however, as they might not work as accurately as expected under certain conditions. Canon will assume no liability for any accident or damage resulting from use of these functions.

Precautions for Use of Optional AC Adapter PA-V17

Warning

???Do not use any AC adapter or AC cable other than the dedicated AC adapter or AC cable.

???Do not put heavy objects on the power cable.

???Do not pull, forcibly bend, scratch or modify the power cable.

???Do not cover or wrap the AC adapter (optional) with a cloth or thick cotton blanket.

Fire or electric shock may result.

Be sure to read the operation manual for PA-V17 before use.

Notes on Cleaning

Warning

??? Do not use alcohol, thinner, benzene or any other flammable solvent. Fire or electric shock may result.

xiv

Safety Precautions

Maintenance

Turn off the power before cleaning the camera ( P. 2-7).

Cleaning of Exterior

1.Dampen a soft cloth with water or diluted neutral detergent and wipe the soiled areas gently.

2.Wipe with a dry cloth.

Cleaning of Lens

Use a commercial lens cleaner to remove soiling on the lens surface.

Scratches on the lens surface may result in undesirable images.

Maintenance for Dome Case

A soiled dome is a cause of poor image quality, so clean the dome periodically.

1.Remove the dome by referring to "Installation Procedure for Direct Mounting on a Ceiling/ Wall" ( P. 2-16) in Chapter 2, "Initial Setting and Installation of Camera".

2.Dampen a soft cloth with water or diluted neutral detergent and wipe the soiled areas gently.

3.Wipe with a dry cloth.

4.When you are done, install the dome case.

To prevent injuries and equipment damage due to falling items, periodically check the brackets and screws for rusting and loosening.

For checkups, please contact the dealer where you purchased the product.

Maintenance for Recessed Mounting Kit (Optional)

To prevent injuries and equipment damage due to falling items, periodically check the brackets and screws for rusting and loosening.

For checkups, please contact the dealer where you purchased the product.

xv

Safety Precautions

xvi

Features of VB-C500D

The VB-C500D is a compact network camera for indoor installation integrating camera and server

features.

Wide-angle Varifocal Lens

Equipped with a wide-angle varifocal lens with a wide angle of 82??, F1.1 and optical 2.4x zoom (digital 4x), the VB-C500D achieves video monitoring in wide-ranging applications, including stores and offices, as well as applications in small areas such as at ATM and in elevator halls.

Compact Design Suitable for Various Installation Environments

The ultra-compact dome camera of 3.7 inches in size (dome diameter) can be installed inconspicuously in locations where appearance is given priority, such as in condominiums and hotel stores.

It can be installed in various ways, such as directly mounting on the ceiling, recessed into the ceiling, and mounting on a wall.

Capturing Color Images at 0.2 Lux

With its high imaging quality, the camera can capture color images at a minimum subject illumination of 0.2 lux while maintaining low noise and high color repeatability (when the 1/30- second Smart Shade Control is turned on).

Digital Night Mode Function to Automatically Adjust to Capturing at Low Illumination

When the illumination is low, such as during nighttime, the capture mode is automatically switched from color to monochrome and Canon's unique low-noise, high-quality imaging technology is used to increase the digital sensitivity. If the Digital Night Mode function is used, images can be captured at a minimum subject illumination of 0.1 lux (when the 1/30-second Smart Shade Control is turned on).

Smart Shade Control

When the background is bright and the subject is difficult to see, you can change the contrast of dark areas to make the subject clearer. Unlike the backlight compensation, blown out of the background can be prevented because bright areas are not controlled. These processes are implemented by the dedicated hardware in the camera, so drops in image quality can be reduced and system load can be decreased compared to when the conventional shade control is used ( "Setting the Smart Shade Control in "Operation Guide").

PoE

The VB-C500D supports Power over Ethernet (PoE*) technology, which enables simultaneous video/audio data transmission and power supply by simply connecting a PoE HUB and a single LAN cable ( P. 2-6). When connecting to a PoE HUB, you need not connect a power adapter to the camera or perform any power wiring.

*PoE stands for Power over Ethernet, which is compliant with the IEEE 802.3af standard by the Institute of Electrical and Electronic Engineers.

1-2

1-3

Features of VB-C500D

Two-Way Audio (Full Duplex)

A microphone or speaker with amplifier can be connected*1 to the camera to transmit/receive audio (full duplex) via the viewer*2. You can select a desired audio input mode from LINE IN and MIC IN by switching the setting on the setting page ( P. 3-7).

*1 Microphones and amplifiers are sold separately.

*2 VK-Lite Viewer is the only viewer that supports two-way audio communication. VB-C500 Viewer only supports audio reception.

Small-scale Video Monitoring by Simplified Recording Software VK-Lite

This product comes with a simplifier version VK-Lite of the optional Network Video Recorder VK-64/VK-16 v2.1 ( P. 1-6). Video captured by up to four cameras can be recorded/displayed in real time, to achieve small-scale video monitoring.

1-4

Bundled Software

1-5

Bundled Software

VB-C500 Viewer Ver. 1.0 ( Overview of VB-C500 Viewer in Operation Guide)

VB-C500D Viewer is for displaying video captured by this camera and controlling the camera. Three users can be set according to the camera control rights, including [Administrator], [Authorized Users] and [Guest Users]. This tool is already built into the camera and need not be installed beforehand ( P. 2-4). JPEG video captured by the VB-C500D can be displayed.

To display MPEG-4 video, install VK-Lite Viewer ( P. 1-7).

Note

To use the camera with VBAdmin Tools for the VB-C60, VB-C300 or VB-C50 series, install VBAdmin Tools for the VB-C50 series first, and then install VB-C300, install VB-C60, and finally install VBAdmin Tools bundled with the camera.

Tip

VB Initial Setting Tool Ver. 5.0 can be used commonly with the VB-C60, VB-C300 and VB-C50 series.

Network Video Recorder VK-Lite v2.1 ( Setup Guide)

VK-Lite v2.1, which is a simplified version of the optional "Network Video Recorder VK-64/VK-16 v2.1" ( P. 1-25), is included in the package. VK-Lite consists of the following two software programs:

1-6

Bundled Software

VK-Lite Viewer

For VK-Lite, following cameras can also be registered and used.

Supported VB-C500D, VB-C60/VB-C60B, VB-C300/VB-C300B

cameras VB-C50i/VB-C50iR, VB-C50FSi, VB-C50Fi

Note

To add a VK-Lite Viewer, you need to purchase an optional "VK-Lite Additional Viewer

License".

1-7

Bundled Software

Key Functional Limitations of VK-Lite and VK-64/VK-16

*1 The maximum limit may be imposed depending on the number of cameras, PC performance and hard disk space, network load, etc.

*2 When multiple storage servers are used, determine one master storage server. This way, cameras registered for each storage server, recorded data, etc., can be managed centrally using the viewer. With VK-Lite, switch the storage servers one by one if multiple storage servers are connected to the viewer.

*3 This function allows the displayed viewer window to be switched at specified intervals.

1-8

Bundled Software

1-9

Bundled Software

VK-Lite Viewer Audio Transmission/Reception (Two-way

Communication)

Audio can be transmitted/received between the VB-C500D and viewer.

Tip

PC, speaker and microphone are sold separately.

1-10

Operating Environment

1-11

Operating Environment

*1 Windows Vista and Windows Server 2008 support the 32-bit and 64-bit editions. Other OSs support only the 32-bit edition.

*2 External hard disks cannot be used.

Tip

The optional VK-64/VK-16 v2.1 does not support Windows Vista Home Premium.

1-12

Notes on Operating Environment

1-13

Notes on Operating Environment

3. Click the [Add program???] button to add [VB Initial Setting Tool].

Notes on Use with Windows Server 2003/Windows Server 2008

Registering the Camera's Top page as a Trusted Site

In Windows Server 2003 and Windows Server 2008, the security level for Internet sites and intranet sites on Internet Explorer is set to [High] by default.

Accordingly, when you access the top page of the camera, VB-C500 Viewer or any setting page, the contents block dialog box appears and the page is not displayed correctly.

To display these pages correctly, register them as trusted sites.

1. When the camera's top page is accessed via Internet Explorer, the following dialog box appears.

1-14

Notes on Operating Environment

2. Clicking [Add] opens the Trusted sites dialog box.

Clear the [Require server verification (https:) for all sites in this zone] check box,

if currently selected.

1 BeforeUse

3. Enter the IP address of the VB-C500D under [Add this Web site to the zone], and then click [Add] to register the site as a trusted site.

For details on registering trusted sites, click the [Learn more about Internet Explorer???s Enhanced Security Configuration...] in the dialog box in 1 and see the displayed overview.

Note that even when the contents block dialog box does not appear, setting pages and operations of VB-C500 Viewer may still be limited because Java script is sometimes disabled under the standard security setting. Once the camera's top page is registered as a trusted site, Java script is automatically enabled.

If the contents block dialog box does not appear, you can follow the procedure below to display the [Trusted Sites] adding dialog box.

1.Click [Tools] on the Internet Explorer screen, select [Internet Options], the [Internet Options] dialog box appears.

2.Next, click the [Security] tab.

1-15

Notes on Operating Environment

3. Select [Trusted Sites], and click [Site].

This completes the process of registering the camera's top page as a trusted site.

Notes on Use with Windows Server 2008

Enabling the Sound Function to Use Audio

In Windows Server 2008, the sound function is disabled by default.

If you want to receive audio on VB-C500 Viewer, enable the sound function by following the procedure below.

1. Click [Control Panel] and select [Hardware and Sound].

1-16

Notes on Operating Environment

1-17

Notes on Operating Environment

Notes on Use with Windows Vista

The following restrictions apply when the VB-C500D is used with Windows Vista Home Premium/

Business/Enterprise/Ultimate.

Network Video Recorder VK-Lite v2.1

Warning dialog box displayed upon opening of the [Storage Server Settings] dialog box

If the User Account Control is enabled in Windows Vista, the User Account Control dialog box appears when the Storage Server Settings tool is started.

Click [Continue] and start the Storage Server Settings tool.

Video Storage Folder

In Windows Vista, do not specify the Windows folder or Program Files folder on the system drive as the folder for storing snapshots and specified video files. Images and videos cannot be saved in these folders.

Shadow Backup Function

The shadow backup function of Windows Vista cannot be used.

If a setting file of VK-Lite was accidentally deleted, for example, the file cannot be restored using the shadow backup function.

1-18

Notes on Operating Environment

1-19

Notes on Operating Environment

Top View of Camera (Without Dome Case)

Reset switch

Turn on the power while pushing this switch. Continue to push the switch for 5 seconds or more to restore all factory settings except for the date and time.

LED

The LED becomes lit/unlit according to the status of the camera.

(1) Installation mode: Lit ( P. 2-23)

(2) Other steady state: Unlit

VIDEO OUT terminal

Mounting screw hole

Use this hole to affix the camera on an installation surface or affix an optional Recessed Mounting Kit.

1-20

1-21

Optional Items

Purchase options separately as necessary.

Audio Interface Cable WA500-VB

Use this interface cable to connect the camera to an audio input/output device (speaker, microphone, etc.).

Marking band

OUT

IN

The terminal marked "1" on the marking band (farther away from the cable branching point) is used for audio output, while the unmarked terminal (closer to the branching point) is used for audio input.

For details on the audio input/output terminals, refer to P. 3-7.

1-22

Optional Items

1-23

Optional Items

Recessed Mounting Kit SR500-S-VB

The Recessed Mounting Kit is a dedicated option for VB-C500D.

Use example

AC Adapter PA-V17

Use this adapter when a PoE HUB or external power supply is not used.

VK-Lite Additional Viewer License

VK-Lite Additional Viewer License is an additional license needed to install VK-Lite Viewer to each PC. You need to purchase the license if you want to view video captured by the camera using VK Viewer from multiple sites.

1-24

Optional Items

1-25

Optional Items

1-26

Initial Setting and

Installation of Camera

The following explains how to install the camera.

First, install the necessary software from the bundled Setup CD-ROM. Next, connect the camera to the network and perform initial setting of the camera. Check the video using VB-C500 Viewer, and then install the camera.

Before installing the camera, be sure to set the IP address.

Flow of Setup

Step 1 Install the software

Insert the bundled Setup CD-ROM in the PC and install the necessary software ( P. 2-4).

PC

Bundled Setup CD-ROM

Step 2 Connect the camera to the network

Connect the VB-C500D and PC to the network ( P. 2-6).

If a PoE HUB or Midspan is used, consult your Canon sales representative.

VB-C500D

LAN cable

PC

PoE HUB

The figure shows connection via a PoE HUB.

2-2

2-3

Step 1 Install the Software

Install the Necessary Software

First, install the necessary software from the bundled Setup CD-ROM ( P. 1-5).

Software for Initial Setting and Management of the Camera

D Install it by executing VBToolsInstall.exe in the VBTools folder of Setup CD-ROM.

Recording Software

This software is used to display and record video captured by the

Network Video

camera. It consists of two components, Storage Server and Viewer

Recorder VK-Lite

( P. 1-6).

D Install it by executing VKLiteInstall.exe in the VBTools folder of Setup CD-ROM.

Note

Use VK-Lite Viewer if you want to display MPEG-4 video from the camera. Only JPEG video can be displayed using the built-in VB-C500 Viewer.

In-Camera Software (Need Not be Installed)

This software is used to display video captured by the camera. The VB-C500 Viewer software is already built into the camera and need not be installed

beforehand ( P. 1-6).

2-4

3. When the installation is complete, an icon appears on the desktop.

This completes the installation.

2-5

Step 2 Connect the Camera to the Network

Connect the Camera to the Network and Turn On the Power

Here, an example of connecting one camera to a PC via a HUB is explained.

VB-C500D comes with a PoE (Power over Ethernet). The power can be supplied to the camera, via a LAN cable, from a PoE HUB conforming to IEEE 802.3af.

Via PoE HUB

LAN cable

Notebook PC

AC power cable

If an AC adapter (optional) or external power supply is used, connect it as shown below.

For details on the connection method, refer to P. 2-9.

Via AC adapter or external power supply

AC power cable

LAN cable

(Back)

HUB

Notebook PC

The figure shows an AC adapter (optional).

2-6

2-7

Step 2 Connect the Camera to the Network

Note

When turning off the power and then turning it back on, wait for at least 5 seconds before turning on the power. If the power is turned on too quickly, the camera may not operate correctly. Also, when disconnecting/connecting the power connection, be sure to observe the instructions provided in "Safety Precautions/Notes on AC Adapter (Optional)" ( P. xiv).

???The current may be limited for each port depending on the PoE HUB used. However, the camera may not operate correctly when the current is limited. If the camera malfunctions, do not limit the current.

???The total current consumption of ports may be limited depending on the PoE HUB used. If multiple ports are used, the ports may not operate correctly. Check the operation manual for the PoE HUB you are using.

2-8

Step 2 Connect the Camera to the Network

2-9

Step 3 Perform Initial Setting of the Camera

Perform Initial Setting of the Camera

Set the network for the VB-C500D using VB Initial Setting Tool.

1.Launches VB Initial Setting Tool.

Double-click the [VB Initial Setting Tool v5.0] icon on the desktop, or click the [Start] menu, click [Programs], click [Webview Livescope], and then select [VB Initial Setting Tool v5.0].

Double-click the icon on the desktop.

2.VB Initial Setting Tool automatically detects the camera connected to the network, and displays the MAC address, IP address and model name of the camera.

Click to select.

The IP address has been set to 192.168.100.1

at the factory. The MAC address is specified on the label attached to the bottom of the camera ( P. 1-21).

Note that VB Initial Setting Tool cannot exceed the subnet mask.

Click to select the MAC address, and then click the [Initial setting] button.

2-10

2-11

Step 3 Perform Initial Setting of the Camera

Note

To set the IP address from the DHCP server, set an address from VB Initial Setting Tool to enable communication with the setup PC and change the setting of [IP Address Setting] under [Network] ("LAN" in Operation Guide) on the Setting page to [Auto (DHCP)].

The camera will stop issuing IP address assignment requests in 20 minutes after its power is turned on, upon which detection by VB Initial Setting Tool will be disabled. In this case, turn on the camera again.

To restore the factory settings, see "Restore Settings" in Operation Guide.

This completes the initial setting.

2-12

Step 3 Perform Initial Setting of the Camera

Note

There may be cautionary information that should be heeded depending on your operating environment. Before the initial setting, refer to "Notes on Operating Environment" ( P. 1-13).

To open the setting page using the [Settings] button, do not change the HTTP port of the camera from 80. For information on setting the HTTP port number, see "HTTP Server" in

Operation Guide.

2-13

Step 3 Perform Initial Setting of the Camera

3. The viewer starts and video captured by the camera is displayed.

Note

Clicking [Setting Page] or [Admin Viewer] on the top page of the camera displays each user authentication window.

The factory-set user name and password are as follows:

User name: root Password: camera

Be sure to change the administrator password for security reasons ("Administrator Password" in Operation Guide).

To display both JPEG and MPEG-4 video, install and use VK-Lite Viewer ( P. 1-7).

Where video can be transmitted to is not limited by the factory settings, etc.

To use the camera for surveillance purposes, etc., be sure to set the [Access Control] options on the setting page. ("Setting User Access Privileges (Access Control)" in

Operation Guide).

Tip

For information on how to use VB-C500 Viewer, see Operation Guide.

When [Setting Page] is clicked, various options can be set. ("Accessing the Setting Menu" in Operation Guide).

This completes the video check process.

2-14

Step 4 Install the Camera

2-15

Step 4 Install the Camera

Installation Procedure for Direct Mounting on a Ceiling/Wall

Side View of mounting

Roof space

Ceiling board

VB-C500D

1.Use the bundled template to determine the installation position of the camera.

Confirm the capturing direction of the camera and determine the positions of camera mounting screws, as well as wiring holes if necessary, using the supplied template.

Screw holes for

M4.0 screws

64.0mm (2.52 in)

Screw holes for

M4.0 screws

2-16

2-17

Step 4 Install the Camera

4.Connect each interface cable.

???This process is not required if you don't use any microphone, sensor, AC adapter or external power supply.

???Select an appropriate interface cable according to the external device used, and connect the cable to the camera.

???The interface cables and camera have dedicated connectors and connection terminals, respectively.

???You can select a desired direction from which to take out the interface cables and other wirings.

Concealing the Wiring in a Ceiling

I/O interface cable

The cable cover has a cutout groove for guiding interface cables.

Cut out the groove, guide the cables through the cutout, and affix the cover to the camera with screws.

Cut out the groove.

2-18

2-19

Step 4 Install the Camera

Wiring on a Ceiling

Cut out the side face of the cover.

Power interface cable

Audio interface cable

I/O interface cable

If the wirings cannot be concealed in the ceiling, cut out the V-groove in the cable cover and take out the wirings from the side face of the camera, and then affix the cable cover with screws.

Cut out the V-groove.

For the types of interface cables, refer to the page on Optional Items ( P. 1-22).

2-20

2-21

Step 4 Install the Camera

5.Connect the LAN cable, and also connect each external device using a cable.

Connect the LAN cable that has been guided through the wiring hole, to the LAN cable on the camera side.

If necessary, connect the audio, I/O or power interface cable to each external device.

6.Affix the camera on the ceiling.

Affix the camera by removing the safety sheet from the camera mounting screw holes on the base of the device (4 locations), and then aligning the screw holes with the camera mounting screw locations marked in step 1.

Screw holes

(4 locations, ??4.6 mm(??0.18 in), M4.0)

7.Adjust the camera angle and focus.

???Push the inner cover in the direction of the arrow, as shown below, to remove the cover.

???Loosen the pan, tilt and rotation lock screws and adjust the lens in a desired direction, and then lock the screws.

2-22

Step 4 Install the Camera

???Next, loosen the focus lock screw.

???Adjust the viewing angle and focus using the zoom adjustment knob and focus ring. When the adjustment is complete, tighten the focus lock screw to lock the focus.

2-23

Step 4 Install the Camera

Tip

Image from the network is disconnected when you switch to the installation mode (when the reset switch is pressed) or return to a normal mode from the installation mode.

In the installation mode, the camera cannot be controlled.

Only NTSC is supported for video output.

The LED remains lit in the installation mode, and a white square is shown on the bottom left of the screen.

8.Install the inner cover and dome case.

Finally, place the inner cover and dome case, and tighten the two screws on the side face.

2-24

Step 4 Install the Camera

2-25

Step 4 Install the Camera

2.Use the template supplied with the Recessed Mounting Kit to determine the installation position of the camera.

Confirm the capturing direction of the camera, and then use the supplied template to open holes for the Backside Ceiling Bracket and in-ceiling bracket.

3. Install the assembled in-ceiling bracket at the back of the ceiling/wall and secure it with screws.

4.Connect the Safety Wire, necessary interface cables and LAN cable, and also connect each external device with a cable, by following steps 2 to 6 of "Installation Procedure for Direct Mounting on a Ceiling/Wall."

2-26

Step 4 Install the Camera

5.Affix the assembled in-ceiling bracket assembled with the camera, on the installation surface.

Hook the assembled in-ceiling bracket on the screws that were loosely secured in step 3, turn the bracket clockwise, and securely tighten (affix) the screws.

Camera of Installation and Setting Initial

6.Adjust the camera angle and focus in the same manner as in step 7 of "Installation Procedure for Direct Mounting on a Ceiling/Wall," and install the dome case.

7.Install the recessed mounting cover.

Finally, align the mark (c) on the recessed mounting cover with the mark (I) on the in-ceiling bracket, and turn the cover clockwise to the mark (I) on the recessed mounting cover to affix the bracket in position.

This completes the installation.

2-27

Step 4 Install the Camera

2-28

External Dimension Drawing

3-2

Main Specifications

*1 Note that the frame rate may drop depending on the performance of the viewer PC, number of clients connected at the same time, network load, etc.

*2 An optional speaker with amplifier is required to play audio.

The specifications are subject to change without notice for purposes of improvement, etc.

3-3

Main Specifications

The specifications are subject to change without notice for purposes of improvement, etc.

3-4

Input/Output Terminals

3-5

Input/Output Terminals

External Device Input Terminals (IN1, IN2)

There are two sets of external device input terminals (IN1, IN2), where each set consists of two terminals. The - terminals are connected to the GND in the camera. Two-wire cables are connected to the + and - terminals to achieve electrical continuity or insulation between the two terminals for notification to the viewer.

Note

For the sensors and switches to be connected, connect terminals that are electrically isolated from each power supply or GND.

External Device Output Terminals (OUT1, OUT2)

There are two sets of external device output terminals (OUT1, OUT2), where each set consists of two terminals. Each terminal set has no polarity. The condition between the two terminals can be switched between connected and disconnected by controlling from the viewer. The output terminals are isolated from the internal circuits of the camera using optical couplers.

The loads connected to the output terminals should be used within the following ratings:

3-6

Tip

Applicable wire for external device cable

Single wire of AWG No. 28 to 22

Conductor size ??0.32 to 0.65 mm (??0.013 to 0.026 in)

Strip the cable by approx. 8 to 9 mm (0.31 to 0.35 in)

Audio Input/Output Terminals

One audio input terminal and one audio output terminal is available.

A microphone, speaker with amplifier or other audio input/output device can be connected to the camera to send/receive sound via the viewer.

To connect the camera to an audio input/output device, use a dedicated audio interface cable WA500-VB.(P. 1-22)

Use a ??3.5 monaural mini jack connector to connect the audio interface cable and audio input/

output device.

Audio Input, Used as Both LINE IN and MIC IN (Monaural Input)

Connects the camera to a microphone. As for audio input of this camera, two types of microphones, LINE IN and MIC IN types, are supported. Note that the camera only has one audio

3-7

Input/Output Terminals

input. Switch the input mode on the Setting page ("Audio Input" in Operation Guide). The factory setting is LINE IN.

When LINE IN is selected, a microphone with amplifier can be connected.

When MIC IN is selected, a dynamic microphone or capacitor microphone can be connected.

Input terminal: ??3.5-mm mini jack (monaural)

???Dynamic MIC IN setting

Input impedance: 1.75 k????? 20%

* Supported microphone

Output impedance: 400??? ~ 600???

???Capacitor MIC IN setting

Input impedance (microphone bias resistance): 2.2 k????? 20%

Microphone power supply: Plug-in power (voltage: 1.8 V) method

*Supported microphone

Capacitor microphone of plug-in power type

???LINE IN setting

Input level: 1 Vp-p max.

*Use a microphone with amplifier.

Audio Output Terminal LINE OUT (Monaural Output)

Connects the camera to an amplifier with speaker. Audio can be sent from VK-Lite Viewer to a speaker. Only the administrator can access this terminal.

Output terminal: ??3.5-mm mini jack (monaural)

???Output level: 1 Vp-p max.

*Use a speaker with amplifier.

3-8

3-9