Welcome

Congratulations on the purchase of your Boss GT-10B Bass Effects Processor. This TurboStart contains step-by-step instructions that will quickly introduce you to many of the GT-10B???s features.

Making Connections

To protect your equipment and your ears, start out with the GT-10B???s upper left OUTPUT knob turned down, and turn down the gear into which you???re plugging your GT-10B.

1 Connect an instrument cable from a bass guitar to the INPUT jack on your GT-10B.

2Plug headphones into the GT-10B???s PHONES jack or connect its OUTPUT jack(s) to

???a bass amp???set to a clean sound.

???a line level input???such as a mixer, PA, recorder, or suitable power amp.

Note: If you???re using one bass amp or one line input, use only the GT-10B???s L/MONO output. If you???re connecting to two amps or a stereo pair of line-ins, use both GT-10B OUTPUT jacks.

Tip: If you???re connecting the GT-10B in stereo, you can take advantage of its stereo-only features such as having Dual L/R amp models or different effects on each side.

Optimizing the GT-10B???s Outputs for the Best Tone

1 Just below the main OUTPUT LEVEL knob, press the OUTPUT SELECT button. 2 Turn the big dial to select a value that matches the device you???re connected to. 3 Press the GT-10B???s EXIT button when you???re finished.

4Raise the GT-10B???s OUTPUT LEVEL knob.

5Raise the volume of your amp or mixer to the desired level.

The GT-10B???s Play Screen

The GT-10B???s main display is the Play screen. To show its eight different views:

1 Press EXIT a couple of times to make sure the display is showing the Play Screen.

2Press the DISPLAY MODE button to cycle through the different Play Screens. For simplicity, you may want select Screen 1???this is the knob-based Play Screen.

Selecting Patches

A patch is a group of effect combinations. Patches are stored in groups of four, each of which is a bank. There are 200 permanent factory Preset patches, and 200 memory locations in which you can store your own User patches. (On the red numerical display, Preset patch names start with a ???P???, while User patches begin with ???U???.)

Note: Straight out of the box, the User banks contain the same patches as the Preset banks, so feel free to replace the User patches with your own???you won???t lose anything.

To select a patch, return to the Play screen as described above, and then:

???Turn the big dial to go through all of the GT-10B???s patches, or

???Use the BANK 6and BANK 5foot pedals to select the desired bank, and then Pedals 1, 2, 3, or 4 to choose the patch you want in the selected bank.

Use CATEGORY Search to Check Out Some Patches

1If necessary, press EXIT a few times to return to the Play Screen.

2Press the CATEGORY/ENTER button???notice that the category, or???CATG???, is displayed in the upper-left corner of the display.

3 Press the 34 buttons on either side of the big dial to select the CATG you wish.

4When you find a category to explore???for example, METAL???use the big dial to

move up and down through the patch list to try out different patches.

5When you???ve found the patch you want, press EXIT to return to the Play screen.

Use EZ TONE to Create a Custom Bass Tone

1Press the EZ TONE CREATE button to the left of the GT-10B.

2Turn the knobs below the display to select the basic tone and variation you want.

Tip: It???s a good idea to play your bass and listen to it throughout this process.

3Using the 4 button, cursor to the DRIVE grid, and then use the 5 and 6 knobs to dial in the drive you want.

4Press the WRITE button.

5 Turn the big dial to select a User patch location, from U01-1 to U50-4.

6Press the WRITE button again???your patch is now saved.