Solution 64

????????????????????????????????????????????????

User Guide

EN Security System

Solution 64 User Guide

Copyright Notice

Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd (???Bosch???). All rights are reserved.You may download a single copy of this publication. By downloading the publication you agree that you will: (i) only use the publication for your own reference; (ii) not commercially exploit or charge any person for the use of the publication;

and (iii) not modify the publication in any way without the prior written permission of Bosch. Except as speci???ed above or where authorised by the Copyright Act 1968 (Cth), no part of this publication may be reproduced, transmitted, modi???ed or stored in any form or by any means, without the prior written permission of Bosch.

Trademarks

Throughout this document trademark names may have been used. Rather than put a trademark symbol in every occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the bene???t of the trademark owner with no intention of infringement of the trademark.

Notice of Liability

While every e???ort has been taken the accuracy of this document, neither Bosch Security Systems Pty Ltd nor any of its o???cial representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book. Should you ???nd any error on inconsistency, please notify us accordingly.

Bosch Security Systems Pty Ltd reserves the right to make changes to features and speci???cations at any time without prior noti???cation in the interest of ongoing product development and improvement.

Telepermit Note

The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions.

This equipment shall not be used in any manner that could constitute a nuisance to other Telecom customers.

Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair.

Thetransmitlevelfromthisdeviceissetasa???xedlevelandbecause of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard telepermitted telephone.

Warnings

1)This product must be installed by a quali???ed and licensed security installer.

2)This product may not perform as expected if installed incorrectly.

3)Some features of this product require a working telephone line to operate and telephone communication service provider charges may be applicable.

4)Australian standard AS 2201 require regular service by quali???ed and licensed security persons and regular user testing. Please consult your security alarm company for further details.

5)Incorrect programming of options can result in operation contrary to what may be desired.

6)Leave the mains adapter plugged in at all times.

7)Leave the telephone line plugged in at all times under normal conditions.

Notice to Owner

Thankyou for selecting the Solution 64 Security Control Panel for your security needs.Your system includes many advanced features and functions which will be programmed and con???gured by your security consultant during installation. Depending on the con???guration, and your access level, you may have the ability to program certain features within the system to suit changes in your security needs. For example you may wish to change a User Name or PIN number when a sta??? member leaves.

This manual explains all aspects of system operation as well as detailling the various programming options available to you. We ask that you take the time to read this manual carefully and that you have your installer explain the basic system operation and con???guration to you when the installation is complete.

Solution 64 User Guide

Contents

Solution 64 User Guide

Program Menu Tree

Table 1: shows all of the system options in a tabular format. Each option can be access by pressing the Menu key and then drilling down using the arrow and OK keys until the required option is listed on the display. A quick way to jump to a particular option is to press the Menu key followed by the speci???c option number.

You may be asked to enter your PIN when accessing some options.

Example:

To set a new call forward number enter MENU + 5 + 1 + 6 and then follow the on screen prompts.

Table 1: Control Panel Menu Tree

Introduc tion

Your system helps to secure life, property and investments against ???re, theft and bodily harm. It consists of a keypad (or keypads), sensors such as motion detectors or devices located on doors and windows, and other sensing devices designed to detect the presence of smoke or combustion. The location and quantity of sensing devices will have already been discussed with you by your alarm installer.

Control of your security system is achieved through the unique Graphic keypad, which displays all system information in written text and graphical symbols. Its versatility and ease of operation, make it ideal for any home or business application.

Features

Listed below are the main features of the Solution 64 control panel.

???Up to 64 Fully Programmable Zones

???Fire Alarm Verification

???Up to 48 Unique PINs

???Up to 5 Relay Outputs (1 amp rating)

???3 Open Collector Outputs

???Supervised Siren Driver

???8 Programmable Schedules

???Up To 8 Areas (Common Area Programmable)

???Built-In Dialler

???Up To 8 Fully Supervised Graphic Keypads

???Keyswitch Input (Programmable)

???256 History Event Memory

???EMI / Lightning Transient Protection

???Programmable Via Keypad

???Remote Programmable Via Upload/Download Software

???Alarm Event Memory

???Automatic Test Reports

???Built-In Telephone Line Fail Monitor

User???s Guide

This user???s guide shows you how to use and maintain your security system. It covers basic functions, such as turning the system on and o??? as well as some general programming. More complex programming and system con???guration should be performed by your installer.

Many of the programming functions described in this guide will have already been programmed by your alarm installer while others may need to be programmed or changed by you. Depending on your particular system con???guration some features described in this manual may not be available. Please discuss this with your alarm installer.

Functions outlined in this user guide may require you to enter your PIN (Personal Identi???cation Number) so make sure you choose a number that is easy to remember. For security reasons do not write this code down or give it to anyone else. If more than one person needs to operate the system then you should create a unique code for them if this has not been done by your installer. This guide will explain how to do this.

Please take the time to familiarise your self with the following terms before reading the rest of this guide.

Zones

A ???Zone??? is a detection device, or group of devices connected to your security system. Zones are identi???ed by the area they monitor, such as a front door, bedroom window or hallway.

Faulted Zones

Solution 64 User Guide

When a zone (such as a door or window) is closed, it is said to be ???normal???. When the door or window is open, the zone is said to be ???faulted???. When you turn your system on, you will usually want all of the zones in your system to be normal, although, you can turn your system on with faulted zones.

Zones Types

There are two basic types of zones, Non 24-hour and 24-hour. See below.

Non 24-Hour Zones

Non 24-hour zones respond to alarm conditions depending upon whether the system is turned on or o???. They are programmed to either respond instantly to alarm conditions or to provide a delay for you to reach the keypad and turn the system o???. Various zones will be located throughout your premises.

When you turn your system on, you have the option of turning on all zones (All On), or just some of the zones (Part On). Refer to

All On and Part On, on page 7 for more information.

Bypassed Zones

A zone which has been bypassed will remain unarmed when the system is armed. You may need to bypass a zone when doing renovations in the building or if a sensor becomes faulty. Bypassed zones will reset the next time the system is disarmed.

24-Hour Zones

24-hour zones are always on and cannot be turned o???, even when the system is turned o??? (disarmed). There are two types of 24-hour zones, ???re zones and non-???re zones.

What Is An Area?

The Solution 64 control panel comes defaulted and programmed for a single area con???guration (Area 1), therefore, all zones are assigned to Area 1. The alarm system can be divided into 8 individual areas running o??? the same control panel. In this case, the security company would assign di???erent sensors (zones) to each area according to the area they belong.

Example:

Partitioning a commercial business to 4 individual areas may be as follows:

Area 1 ??? Main entry/exit area

Area 2 ??? Sales

Area 3 ??? Administration

Area 4 ??? Dispatch

Each area can be controlled individually as if they were separate alarm systems.

All On

When you turn an area All On, you are turning on all non 24-hour zones, both interior (motion detectors) and perimeter (doors and windows of the building).

Part On

When you turn an area Part On, you only turn on some of the non 24-hour zones. Your security company will program which zones are included in this portion. Part zones may include only the perimeter (doors and windows) or your system, or sensors in other areas of your premises. Check with your security company to learn which zones are Part zones.

Solution 64 User Guide

Reporting Alarms

Your system may be programmed to send reports to your security company. Once the report is complete, the system returns the telephone to normal operation (check with your security company).

Your system makes repeated attempts to send reports to your security company. If your system fails to report, the keypad will display the ???service??? symbol.

About the Keypad

Your keypad has 20 keys or buttons. The buttons allow you to input instructions and navigate the menu screens as required. Some buttons have a secondary function which is activated by holding them down for two seconds.

Each button???s function is described below:

Keypad Keys

Use the [MENU] and the numeric keys to enter commands. The [MENU] key is also used to go back one level when navigating through menus or to exit a programming location without saving changes.

The [ON] key allows you to turn an area or output on. To turn all areas on at the same time when the system has been partitioned, press and hold the [ON] key for two seconds.

The [PART] key allows you to turn an area Part On. This key can also be used to bypass a zone or multiple zones when you press and hold for two seconds.

The [OFF] key allows you to turn an area or output o???. To turn all areas o??? at the same time when the system had been partitioned, press and hold the [OFF] key for two seconds.

The [OK] key allows you to save any changes and exit the command.

The [MAIL] key allows you to read stored mail. This key can also be used to initiate a dialler test when you press and hold for two seconds.

The [???] key allows you to move the cursor left when programming text or telephone numbers.

The [???] key allows you to move the cursor right when programming text or telephone numbers.

The [???] key allows you to navigate through menus or to toggle characters when programming telephone numbers.

Pressing the 1 and 3 keys together and

+holding them down for 2 seconds will cause a Panic alarm to be triggered. If

+holding them down for 2 seconds will cause a Fire alarm to be triggered. If programmed

+holding them down for 2 seconds will cause a Medical alarm to be triggered. If

Status Icons / LED???s

The following table describes the function of each of the status icons.

Table 3: Status ICONs, LED Indicator???s and Their Meanings

Keypad Tones

Your keypad emits several distinct tones and displays text to alert you to system events. Additional bells or sirens may also be connected to your system. Bells or sirens mounted on the exterior of your premises alert neighbours to emergencies and provide an audible guide for police and ???re ???ghters.

Figure 1: CM100 Graphic Keypad

Solution 64 User Guide

Basic System Operation

Turning An Area All On

Use this function to turn an area All On. The Solution 64 control panel is factory default only for one area. As soon as you turn an area on, exit time will start. Exit time allows you to exit the premises without sounding an alarm. Your security company programs the length of exit delay time.

Turning The System Off

When the system is on, you must enter through a designated entry door to prevent an alarm. Opening a designated door (e.g. front door) will start entry time. During entry time, the keypad will emit a pulsing tone ???beep??? to remind you to turn the system o???. To turn the area o???, enter your PIN followed by the [OFF] key before the entry delay time expires.

If you enter through the wrong door or fail to turn the system o???

1.Make sure that all zones are normal (not faulted).before the entry delay time expires, you may sound an alarm. If

2.Enter your PIN, then press the [ON] key.

If your PIN is valid and if all zones are normal, exit delay time will start. You should leave now. If your Solution control panel detects a faulted zone, you should return it to normal, or bypass the zone.

During exit delay, you may stop the area from turning on by entering your PIN followed by the [OFF] key.

an alarm occurs, silence the alarm (by entering your PIN followed by the [OFF] key) and call your security company to let them know that it is not an emergency situation.

1.Enter your PIN + [OFF] to turn the system (or area) o???. The keypad will no longer display the ???Lock??? or ???Part??? icons.

Silencing Alarms

3.To turn the system (or area) o???, enter your PIN, then press [OFF].

Turning An Area Part On / Part 2 On

Use this function to turn an area Part On or Part 2 On. The Solution control panel is factory default only for one area. Part On and Part 2 On turns on only part of the area, leaving the rest of the area turned o???.

Only the security company can program which zones are monitored for Part On. The master user can program which zones are monitored when a user turns an area Part 2 On.

Once you have turned an area Part On or Part 2 On, exit delay time starts to count down. You should leave all zones that are active before exit delay time expires. Leaving active zones after exit delay expires causes an alarm event. Use Part On or Part 2 On only when you want part of an area turned on.

1.Make sure that all zones are normal (not faulted).

When the Solution 64 control panel has registered an alarm, the keypad (s) and sirens will sound to alert personnel that an alarm occurred. The keypad will scroll all alarms on the keypad display for visual feedback. If you enter your PIN before the system dials your security company, the alarm report is cancelled (if programmed).

1.Enter your PIN + [OFF] to silence any alarm and turn the system o???.

The keypad will continue to scroll all alarm events that caused the alarm. This is called alarm memory.

2.To clear alarm memory, turn the area on and o??? again (eg.

PIN + [ON] + PIN + [OFF]).

Automatic Arming

Your system may have been programmed to automatically arm itself at a certain time of the day.

2.Enter your PIN, then press the [PART] key.

If your PIN is valid and if all zones are normal, the keypad will prompt you to select Part On or Part 2 On.

3.Using the arrow keys, highlight Part On or Part 2 On then press [OK].

Exit delay time will start. You should leave now. If your system has a faulted zone, you should return it to normal, or bypass the faulted zone.

During exit delay, you may stop the system from turning Part On by entering your PIN followed by the [OFF] key.

4.When exit time has expired, the keypad will display the Part On icon.

5.To turn the system o???, enter your PIN, then press [OFF].

If for some reason you are still in the building when the auto arming is taking place then it is possible to extend or delay the auto-on time (automatic arming time) by one hour simply by entering your PIN during the auto-on pre-alert time. The auto- on pre-alert time sounds the keypad buzzer to warn you that the system will automatically turn All On, Part On or Part 2 On.

Example:

If the control panel is programmed by your installer to automatically turn All On at 6:00pm and the auto-on pre-alert time starts beeping the keypad at 5:55pm, entering your PIN between 5:55pm and 6:00pm will delay the auto-on time by one hour and the auto-on pre-alert time will again commence at 6:55pm. Therefore the system will automatically turn All On at 7:00pm.

Remote Arming - Quick Arm

If you forget to arm your system it may be possible for you to remotely arm it using a touch tone telephone if the remote arm option has been enabled by your installer.

To arm the system call the number which the panel is connected to and when the panel answer you will here 3 beeps in accending frequency if the panel is in the disarmed condition. Press [0] + [#] to arm. You will hear 3 beeps in decending order when the panel arms.

All areas on the system will be armed regardless of there condition when using the DTMF quick arm function.

Duress or Silent alarms

A Duress or Silent Panic alarm can be easily triggered via the keypad if you are being forced to operate the system against your will.

To trigger a duress, enter your normal user PIN followed by the last 2 digits of your user PIN followed by the ON or OFF key. See the following examples.

1)If your PIN is 2580, to send a duress report when the area is o???, Enter, [2] + [5] + [8] + [0] + [8] + [0] + [OK] or [ON].

2)If your PIN is 2580, to send a duress report when the area is on, Enter, [2] + [5] + [8] + [0] + [8] + [0] + [OFF].

System Programming

Some of the examples shown in the following section i assume that you are already in programming mode. Note To enter programming mode simply enter your PIN

and press the MENU key on the keypad.

Access > PIN Codes >

This menu lets you change your own PIN. It is recommended that you write down your old PIN and the new one before you begin. The new PIN must have the same number of digits as your old PIN unless your installer has enabled the variable length PIN option. Once the change is complete you should destroy the written copy.

At factory default, each PIN is ???xed to 4 digits in length. The default PIN for User 1 (Master user) is 2580. Only the security installer can change the PIN length.

Enter programming mode (PIN + MENU) then,

1.Ensure that the system (or area) is turned o???.

2.Enter your PIN, and then press [MENU] + [1] + [1] + [0].The keypad will prompt you to enter a new PIN.

Enter New PIN for

DEBBIE SMITH U002

Press OK or MENU

3.Enter your new PIN, and then press [OK]. If an error tone

Solution 64 User Guide

sounds, try a di???erent PIN. The keypad will now prompt you to enter your new PIN again.

Con???rm New PIN for

DEBBIE SMITH U002

Press OK or MENU

4.Enter your new PIN again.

5.Press [OK] to save and exit, or press [MENU] to exit without saving Your PIN has now been changed.

Programming Text Using The Keypad

When programming text via the keypad, various keys on the keypad operate di???erently.

A group of characters is assigned to each of the numeric keys on the keypad. Pressing the same numeric key again will toggle to the next character assigned to the key (eg. Press the [2] key will display the ???A??? character, press the [2] key again will toggle to the ???B???character, press the [2] key again will toggle to the???C???character etc).

Once the correct character is display use the arrow keys to move to the next letter of the word you are entering.

The key assignments are identical to those found on most ???xed and mobile phones.

When programming text, each numeric key represents a di???erent group of characters.

Pressing the same numeric key repeatedly will step you through the available characters assigned to the key. The text key layout is the same as most phones. Refer to the table below for detailed character information.

Refer to the table below for more information.

Once the desired character is displayed press the right [???] arrow key to move to the next character position.To save programming changes, press [OK], or press [MENU] to exit without saving.

Solution 64 User Guide

Access > PIN Codes >

If you have a master PIN, this command allows you to change somebody else???s PIN. It is recommended that you write down the old PIN and the new one before you begin. Once the change is complete you should destroy the written copy. The new PIN must have the same number of digits as the old PIN.

At factory default, each PIN is ???xed to 4 digits in length. The default PIN for User 1 (Master user) is 2580.

Enter programming mode (PIN + MENU) then,

Ensure that the system (or area) is turned o???.

1.Press [MENU] + [1] + [1] + [1]. The keypad will display a list of available users that you can change their PIN.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ??????, OK or MENU

3.Use the [???] and [???] keys to select the user that you want to change the PIN, then press [OK] to select. Alternatively, you can enter the user number you want to change, then press [OK ].

Please Enter PIN for

4.Enter the new PIN.

If an error tone sounds, try a di???erent PIN.

5.Press [OK] to save and exit, or press [MENU] to exit without saving.

Access > PIN Codes >

This menu allows a Master user to add a PIN to a new user. A Master user can only program a new PIN for those users that have been assigned to the same area(s) as the Master user.

At factory default, each PIN is ???xed to 4 digits in length. The default PIN for User 1 (Master user) is 2580.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [1] + [2].

A list of users will display on the keypad.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ??????, OK or MENU

2.Use the [???] and [???] keys to select the user that you want to add a PIN, then press [OK] to select. Alternatively, you can enter the user number you want

to add, then press [OK].

The keypad will prompt you to enter the new pin.

Enter New PIN for

User 3 Name U003

Press OK or MENU

3.Enter the new PIN for the user you have selected. If an error tone sounds, try a di???erent new PIN.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Access > PIN Codes >

This menu allows a Master user the ability delete other users PIN???s. A Master user can only delete a PIN for those users that have been assigned to the same area(s) as the Master user. A Master user cannot delete their own PIN.

Enter programming mode (PIN + MENU) then,

1.Make sure that the system is turned o???.

2.Press [MENU] + [1] + [1] + [3].

The keypad will list all users that you can delete.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ??????, OK or MENU

3.Use the [???] and [???] keys to highlight the user whose

PIN you want to delete, then press [OK] to select. Alternatively, you can enter the user number you want to delete, then press [OK].

Press OK to delete PIN

For U002 DEBBIE SMITH

Press OK or MENU

4.Press [OK] again to delete the PIN, or press [MENU] to cancel.

Tokens

This section outlines how to add and delete token cards that allow an alternate method for users to turn the system on and o??? via a prox reader enabled Keypad or an external reader. The system can also be con???gured to automaticall open a door if it has been ???tted with an electric door lock. You should discuss this feature with your installer for more details on your particular installation.

A token is a small plastic tag card that has a unique ID. A user can place the token card in front of a keypad that has a built-in token reader to turn the system or speci???c areas on and o???.

Access > Token >

This menu allows a Master user the ability to add a new token for for those users that have been assigned to the same area(s) as the Master user.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [2] + [0].

A list of users will display on the keypad.

2.Use the [???] and [???] keys to select the user that you want to add a token for, then press [OK] to select.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ??????, OK or MENU

3.If you are using a keypad with built in reader the system will prompt you to present the token to the keypad. Once the token is presented the keypad we beep and return to the menu.

To Add token for U001 JOHN SMITH swipe new token

4.If you are learning the token via an external reader the

system will prompt you to select the reader to learn from. Use the [???] and [???] keys to select the reader and then repeat step 3 presenting the token to the external reader.

A Master user can only delete a PIN for those users that have been assigned to the same area(s) as the Master user. A Master user cannot delete their own PIN.

Access > Token >

This menu allows a Master user the ability to delete a token for those users that have been assigned to the same area(s) as the Master user.

Enter programming mode (PIN + MENU) then,

Solution 64 User Guide

1.Enter [MENU] + [1] + [2] + [1].

A list of users will display on the keypad.

2.Use the [???] and [???] keys to select the user who???s token you want to delete, then press [OK] to select.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ??????, OK or MENU

3.When prompted press the [OK] key to con???rm token deletion.

Access > Token >

This menu allows a Master user the ability to identify a token which has been programmed into the system. Only tokens that have been assigned to the same area(s) as the Master user cn be identi???ed.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [2] + [2].

The system will prompt you to present the token to the keypad.

2.Once the token is presented the system will display the owner of the token.

Token belongs to ur002

DEBBIE SMITH

Press OK or MENU

RF Keyfob

This section outlines how to add and delete RF keyfobs that allow an alternate method for users to turn an area(s) on and o???. The RF Keyfob must be compatible with the RF Receiver that has been installed by the security company.

Access > RF Keyfob >

This menu allows the security installer or a master user to program the user???s keyfob ID number.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [3] + [0].

A list of users will display on the keypad.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

PRESS ??????, OK or MENU

Solution 64 User Guide

2.Use the [???] and [???] keys to select the user that you want to add the RF keyfob ID, then press [OK] to select. Alternatively, you can enter the user number you, then press [OK].

The keypad will prompt you to enter the RF keyfob ID number:

Enter keyfob RFid for U016 User 16 Name 000000000

Press OK or MENU

3.Enter the RF Keyfob ID Number

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Access > RF Keyfob >

This menu allows the security installer or a master user to delete the RF keyfob ID that has been assigned to a user.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [3] + [1].

A list of users will display on the keypad.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

PRESS ??????, OK or MENU

2.Use the [???] and [???] keys to select the user that you want to delete the keyfob, then press [OK] to select. Alternatively, you can enter the user number, then press [OK].

OK to delete Keyfob for U002 Debbie Smith 009553507

Press OK or MENU

3.Press [OK] to delete the RF Keyfob ID number and exit, or press [MENU] to exit without saving.

Access > User Properties >

This menu allows the master user to program the user???s name. A maximum of 16 characters can be entered.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [4] + [0].

A list of users will display on the keypad.

U001 JOHN SMITH

U002 DEBBIE SMITH

U003 USER 3 NAME

Press ?????? OK or MENU

2.To program the user name, use the [???] and [???] keys to select the user that you want to program, then press [OK] to select. Alternatively, you can enter the user number you want to program, then press [OK].

The keypad will display the current user name.

User Name U001

User 1 Name

Press ???????????? OK to SAVE

3.Use the [???] and [???] keys to scroll the cursor left and right across the user name text. Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.When the user name is complete, press [OK] to save and exit, or press [MENU] to exit without saving.

Access > User Properties >

This menu allows the master user to program which areas (1 to 8) a user can access. Each user can be assigned to one or multiple areas. The master user is restricted and can only assign another user to any one or multiple areas that the master user has been assigned to. At factory default, each user is assigned to operate Area 1.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [4] + [1].

A list of users will display on the keypad.

2.To assign areas to a user, use the [???] and [???] keys to select the user that you want to program, then press [OK] to select. Alternatively, you can enter the user number you want to program, then press [OK].

The keypad will display which areas the user has been assigned to.

??? Area 1

Area 2

Area 3

Press ?????? OK ON OFF MENU

3.Use the [???] and [???] keys to select the area that you want to assign to the user. Press the [ON] key to assign the user to the area (??? will display) or press the [OFF] key to disable the user from the corresponding area (??? will no longer display).

4.Repeat Step 3 until you have assigned the user to all areas that are required.

5.Press [OK] to save and exit, or press [MENU] to exit without saving.

Timer Groups

Timer Groups are used to restrict users from operating doors outside given times, days or holidays. To do this you need to create a time group, then assign one or more schedules to the

time group to specify the access period, day of the week and holidays. To now restrict the user, they must belong also to the same timer group. This now restricts the user from accessing the system outside the nominated times and days within the schedules linked to the timer group.

User

Can only belong to 1 timer group.

Schedules

Multiple schedules can be linked to the same timer group.

Time Groups

There are 8 di???erent timer groups available.

Timer Group Example

1.To set up a timer group you need to select an unused timer group number from 1 to 8, in this example we will assume timer group number to be 5.

2.Select an unused schedule and program the times and day of the week then assign the schedule to timer group 5.

3.Then under user properties assign the users who you wish to restrict to timer group 5. Remember that you are only able to assign a user to one timer group.

A master code holder is able to change the schedules so they can change the access times for a given user. If a user tries to operate the system outside their assigned timer group periods then access will be denied.

This menu allows you to assign each user to one or more access groups. An access group is used to allow and/or restrict which users have access to various system outputs. These outputs can be used to control door strikes, gates or roller doors etc.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [4] + [5] and select the user from the list then press [OK].

Ur001 John Smith

Ur002 Debbie Smith

Ur003 User 3 Name

Press ?????? OK or MENU

2.Use the up and down arrow keys to highlight the Access Group then press the [ON] key to select or the [OFF] key to deselect.

??? Access Group 1

Access Group 2

Access Group 3

Press ?????? OK ON OFF MENU

3.Repeat Step 2 until all required Access Groups are programmed, then press [OK] to save and exit or press [MENU] to exit without saving.

Access > User Properties >

This menu is used to assign a User to a Timer Group. Timer Groups can be used to restrict User access to be within speci???c times de???ned by schedules. Each User can only be assigned to one Timer Group. Setting this option to 0 will give the User 24 hour access to the system.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [1] + [4] + [4] and select the user from the list then press [OK].

Ur001 John Smith

Ur002 Debbie Smith

Ur003 User 3 Name

Press ?????? OK or MENU

2.Using the numeric keys, enter the Timer Group. Valid entries are 1 ??? 8 or 0 to disable.

Timer Group Ur001

00

Press 0-9 OK to SAVE

3.Press [OK] to save and exit or press [MENU] to exit without saving.

Areas

The Solution 64 control panel has the ability to be partitioned up to 8 individual areas. This section outlines various commands that control individual areas.

Areas > Commands >

This menu allows users the ability view the area status of the current area or the status of a di???erent area. This menu is only available via a keypad who???s corresponding area is turned o???.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [0].

A list of available areas will display on the keypad.

A001 Main Of???ce

A002 Production

A003 Warehouse

PRESS ??????, OK or MENU

2.Use the [???] and [???] keys to select the area that you want to view the status information, then press [OK] to select. Alternatively, you can enter the area number, then press [OK].

The keypad will display the area status information.

Solution 64 User Guide

Main Of???ce A001

Disarmed

Press OK or MENU

If the area is turned All On, the keypad will display:

Main Of???ce A001

Armed All On

If the area is turned Part On, the keypad will display:

Main Of???ce A001

Armed Part On

3.To exit, press [OK].

Areas > Commands >

This menu allows you to turn an area All On or o???. Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [1].

A list of di???erent areas will display on the keypad.

A001 Reception Area

A002 Sales Dept ???

A003 Administration Dept

Press ??????, OK or MENU

If an area has already been turned All On or Part On, a ???tick??? (???) will be displayed on the right side of the name description (see A002 Sales Dept above).

2.Use the [???] and [???] keys to select the area that you want to turn on or o???, then press [OK] to select. Alternatively, you can enter the area number you want to turn on or o???, then press [OK].

Areas > Commands >

This menu allows you to turn on all areas that your PIN has been assigned to at the same time All On. The keypad display below shows the area icons 1 through to 8.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [2].

The keypad will display the exit time bar to prompt you to exit all areas. You should leave all areas now.

Area 1 Name

EXIT NOW

When exit time has expired, the keypad will display that all areas are turned All On (Armed).

Area 1 Name

ARMED

Fri,Aug,13 5:34 pm

Area icons will only display if programmed to i do so by your security installer.

Note

Areas > Commands >

This menu allows you to turn o??? all areas that your PIN has been assigned to at the same time. However, this menu requires at least one area that has a keypad assigned to it to be disarmed before you can access this command.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [3].

Areas > Commands >

This menu allows you to operate multiple areas from the same keypad when the system has been partitioned. Before operating a di???erent area, you will need to move the keypad to the area that you want to operate.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [4].

A list of di???erent areas will display on the keypad.

A001 Reception Area

A002 Sales Dept

A003 Administration Dept

Press ??????, OK or MENU

2.Use the [???] and [???] keys to select the area that you want to move the keypad display to, then press [OK] to select. Alternatively, you can enter the area number that you want to move the keypad display to, then press [OK].

Areas > Commands >

Chime mode allows you to monitor a zone (or group of zones) to sound the keypad buzzer or activate a programmable output when the corresponding area is turned o??? (disarmed). This can be useful when you need to monitor the front or back entrance to the premises.

This menu allows a user to turn chime mode on or o???. Only keypads programmed to sound the chime tone will be heard when a zone programmed for chime is faulted.

The master user can Set Chime Zones on page 16. This allows the master user to program which zones can be monitored for chime.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [0] + [5].

A list of di???erent areas will display on the keypad.

A001 Reception Area ???

A002 Sales Dept

A003 Administration Dept

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the area that you want to turn chime mode on or o???, then press [OK] to select. Alternatively, you can enter the area number that you want to turn chime mode on or o???, then press [OK].

The keypad will display the following when chime mode is turned o???:

Reception Area A001

Chime Is OFF,

To Turn ON, Press ON.

To Go Back Press OK

The keypad will display the following when chime mode is turned on:

Reception Area A001

Chime Is ON,

To Turn OFF, Press OFF.

To Go Back Press OK

3.Press the [ON] key to turn chime mode on, or, press [OFF] to turn chime mode o???.

4.Press the [OK] key to exit.

This menu allows you to program the name for each area. Each area name can be programmed with up to 16 characters. At factory default, only Area 1 is used. The Solution 64 control panel can have a maximum of 8 independent areas programmed.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [2] + [1] + [0].

A list of di???erent areas will display on the keypad.

2.Use the [???] and [???] keys to select the area that you want to program the name, then press [OK] to select. Alternatively, you can enter the area number that you want to program the name, then press [OK].

The keypad will display the following:

Area Name A001

Area 1 Name

Press ???????????? OK to SAVE

3.Use the [???] and [???] keys to scroll the cursor left and right across the area name text. Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.When the user name is complete, press [OK].

Inputs

Your Solution 64 control panel has up to a maximum 64 zones. When the optional radio receiver is ???tted any available zone may be programmed as a wireless zone. Your installer will advise you on the exact makeup and con???guration of your system.

Inputs > Commands >

This menu allows you to view the zone status of each zone (i.e. Normal, Open or Short).

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [0] + [0].

A list of di???erent zones will display on the keypad.

2.Use the [???] and [???] keys to select the zone that you want to turn view the status information then press [OK] to select. Alternatively, you can enter the zone number that you want to view status information, then press [OK].

The keypad will display the following zone status information:

Zone 1 Name Z001

EOL=Normal 06523 ohms

Press OK or MENU

3.Press the [OK] key to exit.

Solution 64 User Guide

Inputs > Commands >

This menu allows you to bypass or un-bypass a single or multiple zones before you turn the area All On, Part On or Part 2 On. When bypassing zones, it disables the ability for a zone to detect intrusion and sound an alarm.

A burglary zone will automatically become un-bypassed when you turn the corresponding area o??? (disarm). Any 24-Hr ???re or 24-Hr non ???re zones will need to be manually un-bypassed.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [0] + [2].

A list of zones that can be bypassed will display on the keypad. A ????????? displayed on the right side of the zone name indicates that the zone is already bypassed.

Z001 Zone 1 Name ???

Z002 Zone 2 Name

Z003 Zone 3 Name

Press ?????? OK or MENU

Inputs > Commands >

This menu allows you to program zones to be monitored when the system is turned o???. Chime mode is ideal to monitor a front door to sound the keypad buzzer when opened (faulted).

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [0] + [3].

A list of areas will display on the keypad.

2.Use the [???] and [???] keys to select the area that you want to program zones for chime mode, then press [OK]. Alternatively, you can enter the area number that you want to program chime zones, then press [OK].

The keypad will list all zones that can be programmed for chime mode. A ????????? displayed on the right side of the zone name indicates that the zone is already set for chime.

Z001 Zone 1 Name ???

Z002 Zone 2 Name

Z003 Zone 3 Name

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the zone that you want to bypass, then press [OK]. Alternatively, you can enter the zone number that you want to bypass, then press [OK].

If the zone is bypassed, the keypad will prompt:

Zone 1 Name Z001 is bypassed. To un-bypass, press OFF.

Press OK or MENU

If the zone is not bypassed, the keypad will prompt:

Zone 1 Name Z001 is un-bypassed. To bypass, press ON.

Press OK or MENU

3.Press [ON] or [OFF] to toggle the zone to be bypassed/un- bypassed.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Repeat steps 1 to 4 to bypass or un-bypass additional zones.

3.Use the [???] and [???] keys to select the zone that you want to set for chime, then press [OK]. Alternatively, you can enter the zone number that you want to set for chime, then press [OK].

If the zone is not programmed for chime, the keypad will prompt:

Zone 1 Name Z001

Zone Chime is OFF,

To turn ON, Press ON.

To Go Back Press OK

If the zone is programmed for chime, the keypad will prompt:

Zone 1 Name Z001

Zone Chime is ON.

To turn OFF, Press OFF.

To Go Back Press OK

4.Press [ON] or [OFF] to toggle the zone to be monitored when chime mode is turned on.

5.Press [OK] to save and exit, or press [MENU] to exit without saving.

Inputs > Commands >

This menu allows you to program which zones are to be monitored when an area has been turned Part 2 On.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [0] + [4].

A list of areas will display on the keypad.

2.Use the [???] and [???] keys to select the area that you want to program zones for Part 2 On, then press [OK]. Alternatively, you can enter the area number that you want to program Part 2 On zones, then press [OK].

The keypad will list all zones that can be programmed for Part 2 On. A ????????? displayed on the right side of the zone name indicates that the zone is already bypassed.

Z001 Zone 1 Name ???

Z002 Zone 2 Name

Z003 Zone 3 Name

Press ?????? OK or MENU

3.Use the [???] and [???] keys to select the zone that you want to set for Part 2, then press [OK]. Alternatively, you can enter the zone number that you want to set for Part 2, then press [OK].

If the zone is not programmed for Part 2, the keypad will prompt:

Zone 1 Z001

Is not a PART2 Zone,

To Enable, Press ON.

To Go Back Press OK

If the zone is programmed for Part 2, the keypad will prompt:

Zone 1 Z001

Is a PART2 Zone,

To remove, Press OFF.

To Go Back Press OK

4.Press [ON] to monitor the zone when the area is turned Part 2 On, or press [OFF] so that you do not monitor the zone when the area is turned Part 2 On.

5.Press [OK] to save and exit, or press [MENU] to exit without saving.

This menu allows you to reset smoke sensors.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [0] + [5].

A list of di???erent areas will display on the keypad.

2.Use the [???] and [???] keys to select the area that you want to reset the smoke detectors, then press [OK] to select. Alternatively, you can enter the area number, then press [OK].

The keypad will display the following:

Smoke detector reset in

Progress. Please wait

3.The keypad will automatically return to the menu when all smoke detectors in the area has been reset.

Inputs > Zone Properties >

This menu allows you to program up to 16 characters for the name of each zone.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [3] + [1] + [0].

A list of di???erent zones will display on the keypad.

2.Use the [???] and [???] keys to select the zone name that you want to change, then press [OK] to select. Alternatively, you can enter the zone number, then press [OK].

The keypad will display the following:

Zone Name Z001

Zone 1 Name

Press ???????????? OK to SAVE

3.Use the [???] and [???] keys to scroll the cursor left and right across the zone name text. Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Solution 64 User Guide

Inputs > Input Testing >

This menu allows you to test all zones within an area at the same time. To successfully walk test each zone, you must open and close each zone.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [3] + [9] + [0].

The keypad will display a list of areas that are available to walk test zones.

2.Use the [???] and [???] keys to select the area that you want to do walk test, then press [OK] to select. Alternatively, you can enter the area number, then press [OK].

The keypad will scroll all zones that you can test.

To test Z001 open then close Zone 1 Name

Press OK or MENU

To test Z002 open then close Zone 2 Name

Press OK or MENU

3.Open and close each zone that needs to be tested. A zone that has been successfully tested will no longer scroll on the keypad display.

When all zones have been tested, the keypad will display:

Selected zones have been

Tested OK

Press OK or MENU

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Inputs > Input Testing >

This menu allows you to select a single zone to be tested via walk test.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [3] + [9] + [1].

The keypad will display a list of zones that are available to be tested via walk test.

2.Use the [???] and [???] keys to select the zone that you want to walk test, then press [OK] to select. Alternatively, you can enter the zone number, then press [OK].

The keypad will display the zone to be tested.

To test Z001 open then close Zone 1 Name

Press OK or MENU

3.Open and close the zone that needs to be tested.

When the zone has been successfully faulted and restored, the keypad will display:

Z001 Zone 1 Name

Test Successful

Press OK or MENU

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Outputs

The Solution 64 control panel has up to a maximum of 8 outputs. 4 outputs are available as standard with an additional 4 available when the optional output expander is ???tted. Your installer will advise you on the exact makeup and con???guration of you system.

Outputs > Commands >

This menu allows you to view the status of each output. Enter programming mode (PIN + MENU) then,

1.Ensure that the system is turned o???.

2.Press [MENU] + [4] + [0] + [0].

The keypad will display a list of outputs that the status may be viewed.

3.Using the [???] and [???] keys, highlight the output that you want to view the status information, then press [OK] to select. Alternatively, you can enter the output number and then press [OK].

The keypad will display the following when the output is o??? and OK:

Output 1 Name O001

Is Off and Ready

Press OK or MENU

The keypad will display the following when the output is o??? and missing:

Output 1 Name O001

Is Off and Ready

Connection Trouble

Press OK or MENU

The keypad will display the following when the output is ON and OK:

Output 1 Name O001

Is ON and Ready

Press OK or MENU

The keypad will display the following when the output is ON and missing:

Output 1 Name O001

Is ON and Ready

Connection Trouble

Press OK or MENU

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Outputs > Commands >

Thismenuallowsyoutoturnoutputsthathavebeenprogrammed by your security company on or o???. These outputs can be programmed to control outside lighting, pool pumps, watering systems etc.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [4] + [0] + [1].

If a valid PIN is required, the keypad will prompt you to enter your PIN.

2.Use the [???] and [???] keys to select the output name that you want to change, then press [OK] to select. Alternatively, you can enter the output number, then press [OK].

3.To toggle the output on or o???, use the [ON] and [OFF] keys.

The keypad will display the following when the output is o???:

Solution 64 User Guide

Output 1 Name O001

Output is OFF,

To Turn ON,Press ON.

To Go Back Press OK

To turn the output on, press [ON].

The keypad will display the following when the output is on:

Output 1 O001

Output is ON,

To Turn OFF,Press OFF.

To Go Back Press OK

To turn the output o???, press [OFF].

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Outputs > Properties >

This menu allows you to program the name for each output. Each output name supports up to 16 characters.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [4] + [1] + [0].

A list of di???erent outputs will display on the keypad.

2.Use the [???] and [???] keys to select the output name that you want to change, then press [OK] to select. Alternatively, you can enter the output number, then press [OK].

The keypad will display the following:

Output Name O001

Output 1

Press ???????????? OK to SAVE

3.Use the [???] and [???] keys to scroll the cursor left and right across the output name text. Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

Solution 64 User Guide

Outputs > Output Testing >

This menu allows you to test any external sirens which have been connected by your installer. The test will last for 5 seconds.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [4] + [9] + [0].

If the system has been partitioned, the keypad will display a list of areas.

A001 Area 1 Name

A002 Area 2 Name

A003 Area 3 Name

PRESS ?????? OK or MENU

2.Use the [???] and [???] keys to select the area that you want to test the siren, then press [OK]. Alternatively, you can enter the area number, then press [OK].

The keypad will display the following during the siren test.

External Audible Testing Press any key to abort

Press OK or MENU

When the siren test is complete, the keypad will display the following:

Testing Complete. Press

OK to continue

Press OK or MENU

3. Press [OK] to exit.

Outputs > Output Testing >

This menu allows you to test any internal sirens which have been connected by your installer. The test will last for 5 seconds.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [4] + [9] + [1].

If the system has been partitioned, the keypad will display a list of areas.

A001 Area 1 Name

A002 Area 2 Name

A003 Area 3 Name

PRESS ?????? OK or MENU

2.Use the [???] and [???] keys to select the area that you want to test the bell, then press [OK]. Alternatively, you can enter the area number, then press [OK].

The keypad will display the following during the bell test.

Internal Audible Testing

Press any key to abort

Press OK or MENU

When the bell test is complete, the keypad will display the following:

This menu allows you to test the external strobe light. Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [4] + [9] + [2].

If the system has been partitioned, the keypad will display a list of areas.

A001 Area 1 Name

A002 Area 2 Name

A003 Area 3 Name

PRESS ?????? OK or MENU

2.Use the [???] and [???] keys to select the area that you want to test the strobe, then press [OK].

Alternatively, you can enter the area number, then press [OK].

The keypad will display the following during the strobe test.

Strobe Activated. Will

Reset On exit

Press OK or MENU

Check and verify that the strobe light is on.

3.Press [OK] to exit.

Communication / Reporting

Programming options in this section relate to how you alarm syetm will communicate alarm information. Your installer will advise you on the exact makeup and con???guration of your system.

Comms > Commands >

This menu allows you to initiate a modem call to the installer???s o???-site computer for programming changes or updates. Your installer may request that you enter this command so that they can remotely service and con???gure you system. You should not enter this command unless requested to do so.

Comms > Commands >

This menu allows you to turn on and o??? the call forward feature. When you turn on call forwarding, the Solution 64 control panel will automatically activate and de-activate the call forward on and call forward o??? sequence accordingly when you turn Area 1 All On and o??? (arm and disarm).

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [5] + [0] + [2].

If the call forward status is o???, the keypad will display:

Call Forward On/Off

Call Forward is OFF,

To turn ON, Press ON.

To Go Back Press OK

If the call forward status is on, the keypad will display:

Call Forward On/Off

Call Forward is ON,

To turn OFF, Press OFF.

To Go Back Press OK

2.To toggle call forward on, press the [ON] key or press the [OFF] key to turn call forward o???.

3.Press [OK] to save and exit, or press [MENU] to cancel.

Comms > Commands >

Reserved for future use

Domestic reporting allows the Solution 64 control panel to send reports to personal telephone numbers (eg. mobile telephone numbers). Up to three di???erent telephone numbers can be programmed, each having a maximum of 32 digits.

A telephone call needs to be acknowledged by the user that answers the incoming call. If the user fails to acknowledge the call, the Solution 64 control panel will make another attempt to report until the maximum number of call attempts are reached. To acknowledge the call, the user needs to press the [#] key on their telephone.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [5] + [1] + [5].

If the control panel is con???gured to report via domestic format, the keypad will display the following:

Domestic Reports Not

Enabled. Please contact

Your Security Service

Provider

If the control panel has been con???gured to report via domestic format, the keypad will display information for telephone number 1.

Domestic Phone Number 1

631728_

Press ?????? 0-9 OK to SAVE

2.Using the numeric keys, enter all the digits of the ???rst telephone number.

You can change a single digit by scrolling the cursor left [???] and right [???]. For special characters (eg. , = pause * or # etc), use the [???] and [???] keys. To clear all text from the cursor position to the right, press the [OFF] key.

3.Press [OK] to program telephone number 2.

Domestic Phone Number 2

4331_

Press ?????? 0-9 OK to SAVE

4.Using the numeric keys, enter all the digits of the second telephone number (if required).

You can change a single digit by scrolling the cursor left [???] and right [???]. For special characters (eg. , = pause * or # etc), use the [???] and [???] keys. To clear all text from the cursor position to the right, press the [OFF] key.

5.Press [OK] to program telephone number 3.

Solution 64 User Guide

Domestic Phone Number 3

6789_

Press ?????? 0-9 OK to SAVE

6.Using the numeric keys, enter all the digits of the third telephone number (if required).

You can change a single digit by scrolling the cursor left [???] and right [???]. For special characters (eg. , = pause * or # etc), use the [???] and [???] keys. To clear all text from the cursor position to the right, press the [OFF] key.

7.Press [OK] to save and exit, or press [MENU] to cancel.

Comms > Commands >

When you leave your premises, you no longer need to remember tomanuallyactivatetheCallForwardOnfeatureviathetelephone. These addresses allow you to program the Call Forward On sequence that the Solution 64 control panel will automatically use when you turn Area 1 ???On???.

In Australia, a typical sequence of activating the Call-Forward On

??? After Time (All Calls) is described below:

For other countries please substitute the appropriate commands after consultaion with your telephone company.

Enter programming mode (PIN + MENU) then,

1.*61 (To turn Call Forward On ??? After Time).

2.Telephone number that you want calls to go to (e.g. 0416123456).

3.*5# (End of Call Forward sequence after 5 seconds).

Therefore, you would program the above steps as follows: *610416123456*5#.

Comms > Commands >

When you enter your premises, you no longer need to remember to manually disable the Call Forward feature via the telephone. These addresses allow you to program the Call Forward O??? sequence that the Solution 64 control panel will automatically use when you turn Area 1 ???O??????.

In Australia, a typical sequence of activating the Call Forward O??? feature is described below:

For other countries please substitute the appropriate commands after consultaion with your telephone company.

Enter programming mode (PIN + MENU) then,

1.#61 (To turn Auto-Forward After Time - O???).

2.# (End of Call-Forward sequence).

Therefore, you would program the above steps as follows: #61#

1.Enter [MENU] + [5] + [1] + [7].

The keypad will display the current call-forward o??? sequence.

Call Forward Off N001

_

Press ?????? 0-9 OK to SAVE

2.Using the numeric keys, enter all the digits of the call forward o??? sequence.

You can change a single digit by scrolling the cursor left [???] and right [???]. For special characters (eg. , = pause, * or # etc), use the [???] and [???] keys.

1.Enter [MENU] + [5] + [1] + [6].

The keypad will display information for telephone number 1.

Call Forward On N001

Press ?????? 0-9 OK to SAVE

2.Using the numeric keys, enter all the digits of the call forward on sequence.

You can change a single digit by scrolling the cursor left [???] and right [???]. For special characters (eg. , = pause * or # etc), use the [???] and [???] keys.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

Comms > Registration >

Reserved for future use

Comms > Periodic Test >

This menu allows you to test the reporting functions of the Solution 64 control panel by manually sending a ???Test??? report to the receiving party (i.e. security company monitoring station, mobile telephone etc).

1.Enter [MENU] + [5] + [9] + [0].

The keypad will prompt that it is in the process of sending a test report.

Comms testing in progress. Please wait..

To Go Back Press OK

If the test is successful, the keypad will prompt:

Communications Test

Successful

If the test is NOT successful, the keypad will prompt:

Test Report Failed

Please call for service

Press OK or MENU

2.Press [OK] or [MENU] to exit.

Devices and Optional Modules

Programming options in this section relate to the keypads and other devices which may be connected to your alarm system.Your installer will advise you on the exact makeup and con???guration of your system.

Devices > Commands >

This option provides a listing of all of the devices and modules connected to your system. Using this option it is poosible to view the voltage, temperature and other information about each of the modules.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [6] + [0] + [0].

Kp001 Keypad 001

Kp002 Keypad 002

Ox001 OutputX 001

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the device that you want to view, then press [OK] to select.

Solution 64 User Guide

3.The display will show each parameter for the device one at a time on the third line of the screen.

Keypad 001 Kp001

Graphic + Prox V1.01

Volts = 13.87

Press OK or MENU

4.Press [OK] or [MENU] to exit.

Devices > Keypads >

This menu allows you to adjust the volume of the keypad???s buzzer. Each keypad will need to have their volume adjusted separately.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [6] + [1] + [0]. The keypad will display:

Keypad 001 Volume

L H

Press OK to SAVE

2.Use the [???] and [???] keys or use the [???] and [???] keys to increase or decrease the volume of the keypad buzzer until the desired volume has been reached.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

Devices > Keypads >

This menu allows you to adjust the contrast of the keypad???s LCD display. Each keypad can have their display adjusted separately.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [6] + [1] + [1].

The keypad will display the contrast screen.

Keypad 001 Contrast

L H

Press OK to SAVE

2.Use the [???] and [???] keys to adjust the bar until the desired contrast is reached.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

This menu allows you to adjust the brightness of the keypad???s LCD display backlight. Each keypad can have their display adjusted separately.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [6] + [1] + [2].

The keypad will display the backlight screen.

Keypad 001 Backlight

L H

Press OK to SAVE

2.Use the [???] and [???] keys to adjust the bar until the desired backlight is reached.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

System Events

Options in this section relate to programming of system wide options and interpretation of system trouble events when and if they occur. Some events such as open zones will appear and single events while other may be grouped together. In this case you need to drill down to see the speci???c detail for each event. Your installer will advise you how to interrogate system trouble events.

System > Commands >

The panel staus menu displays the panel software version information as well as highlighting any system troubles that are currently in effect. This is a view only location.

System > Commands >

To determine the non system (zone) trouble condition, highlight the zone number Z001 to Z064) that you want to view using the [???] and [???] keys, then press [OK] to select.

P001 System Trouble

Z001 Zone 1 Name

Z002 Zone 2 Name

Press ?????? OK or MENU

2.If viewing system trouble conditions, the keypad will display similar to the following:

Panel 001 P001

Voltage= 13.9V Temp=36

Date And Time

Press OK or MENU

The third line of the keypad display scrolls between all current system trouble events.

If viewing non-system trouble conditions, the keypad will display similar to the following:

Zone 1 Name Z001

EOL = Open

Press OK or MENU

3.Press [OK] or [MENU] to exit the system trouble menu command:

If there are no system troubles, the keypad will display:

There are no

System troubles.

Press ?????? OK or MENU

The System Trouble Menu displays all current system troubles in a list format. Some trouble events require you to drill down and non-system trouble that are curent within the Solution 64 control panel.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [0] + [1].

The keypad will display a list of all current system and non system trouble conditions.

To determine the system trouble condition, highlight the

panel number (P001 to P002) that you want to view using the [???] and [???] keys, then press [OK] to select.

P001 System Trouble

Z001 Zone 1 Name

Z002 Zone 2 Name

Press ?????? OK or MENU

Refer to the Trouble Messages table for a complete list of trouble events and their meanings.

Solution 64 User Guide

Table 5: Control PanleTrouble Messages

Solution 64 User Guide

System > Commands >

This menu allows you to review the last 256 history events (from most recent to least recent).

Each event will display:

Line 1 - Displays Event Number

-Date / Time

-Destination 1 and/or 2 report status (S= Sent, P = Pending, F = Fail, A = Abort and L = Log Only).

Line 2 - Displays the source of the event (eg. zone name and zone number or user name and user number)

Line 3 - Displays the event description.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [0] + [2].

The keypad will display the most recent event stored in the history log.

E001 Mon,01Oct 03:41 S1L2

Manual Test Report

Press ?????? OK or MENU

2.Use the [???] and [???] keys scroll between history events.

3.Press [OK] or [MENU] to exit.

System > Clock >

This menu allows you to program/adjust the date and time in the Solution 64 control panel.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [1] + [0].

The keypad will display the current date and time.

Set Date And Time

01-Jan-2004 04:37am

Press ???????????? OK to SAVE

2.Use the [???] and [???] keys to program the month, day, year, hour and minute. Use [???] and [???] keys to scroll cursor left and right to between the month, day, year, hour and minute.

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > Schedules >

This menu allows you to program 16 characters of text for each schedule name.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [7] + [5] + [0].

A list of schedules will display on the keypad.

Sk001 Schedule 1 Name

Sk002 Schedule 2 Name

Sk003 Schedule 3 Name

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the schedule name that you want to change, then press [OK] to select. Alternatively, you can enter the schedule number, then press [OK].

The keypad will display the following:

Name S001

Schedule 1 Name

PRESS ???????????? OK to SAVE

3.To program the schedule name, use the [???] and [???]

keys to scroll the cursor left and right across the user name text. Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > Schedules >

This menu allows you to program both the start time and stop time of each schedule.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [7] + [6] + [2].

A list of schedules will display on the keypad.

Sk001 Schedule 1 Name

Sk002 Schedule 2 Name

Sk003 Schedule 3 Name

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the schedule that you want to change, then press [OK] to select. Alternatively, you can enter the schedule number, then press [OK].

The keypad will display the following:

Sk001 Schedule 1 Name

Start Time: 00:00

Stop Time: 00:00

Press 0-9 OK to SAVE

3.Enter the new start and stop times in 24-hour format (00:00 to 23:59 hours).

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > Schedules >

This menu programs which days of the week the timer execute function will operate. To toggle the day of the week on/o???, press the corresponding number on the keypad (e.g. to turn Monday on, press [2] + [OK], to toggle Monday o???, press [2] + [OK] ).

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [7] + [5] + [2].

A list of schedules will display on the keypad.

Sk001 Schedule 1 Name

Sk002 Schedule 2 Name

Sk003 Schedule 3 Name

Press ?????? OK or MENU

2.Use the [???] and [???] keys to select the schedule that you want to change, then press [OK] to select. Alternatively, you can enter the schedule number, then press [OK].

The keypad will display the following:

3.Press [1] to [8] to enable/disable the days of the week that the schedule will operate.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > Holidays >

This menu allows you to program 16 characters for the holiday name.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [7] + [0] + [6].

A list of holiday names will display on the keypad.

2.Use the [???] and [???] keys to select the timer name that you want to change, then press [OK] to select. Alternatively, you can enter the timer number, then press [OK].

The keypad will display the following:

Name H001

Holiday 1 Name

PRESS ???????????? OK to SAVE

3.To program the holiday name, use the [???] and [???] keys to scroll the cursor left and right across the user name text.

Solution 64 User Guide

Use the [???] and [???] keys to scroll through the di???erent characters available. To clear all text from the cursor position to the right, press the [OFF] key.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > Holidays >

This menu allows you to program the start date and the stop date of each holiday period.

Enter programming mode (PIN + MENU) then,

1.Enter [MENU] + [7] + [6] + [1].

A list of holiday names will display on the keypad.

2.Use the [???] and [???] keys to select the holiday that you want to change, then press [OK] to select. Alternatively, you can enter the holiday number, then press [OK].

The keypad will display the holiday start date:

Holiday Dates H001

Press ???????????? OK to SAVE

3.To program the holiday start date and stop date, use the [???] and [???] keys to scroll the cursor left and right between the holiday day and month. Use the [???] and [???] keys to scroll the day and month.

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > System Options >

The keypad Hi/Lo temperature allows you to program the minimum (0 ??C) and maximum (50 ??C) temperatures the keypad will monitor (tolerance = +/- 2 ??C).

If the temperature falls below the minimum temperature, the keypad will display ???Low Temp ??xx???. If the temperature increases above the maximum temperature, the keypad will display ???High temp ??xx???.

(xx = programmed temperature to be monitored). Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [7] + [3].

The keypad will display the current temperature settings.

Keypad Hi/Lo Temp

Press ???????????? OK to SAVE

2.Use the [???] and [???] keys to program the ???High??? and ???Low???

temperatures. To toggle between the ???High??? and ???Low??? temperature, use the [???] and [???] keys (Range = 0??C to 50??C).

3.Press [OK] to save and exit, or press [MENU] to exit without saving.

Solution 64 User Guide

System > System Testing >

This menu allows you to test all zones within an area at the same time.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [9] + [0].

The keypad will display a list of areas that are available to walk test zones.

2.Use the [???] and [???] keys to select the area that you want to do walk test, then press [OK] to select. Alternatively, you can enter the area number, then press [OK].

The keypad will scroll all zones that you can test.

To test Z001 open then close Zone 1 Name

Press OK or MENU

To test Z002 open then close Zone 1 Name

Press OK or MENU

3.Open and close each zone that needs to be tested. A zone that has been successfully tested will no longer scroll on the keypad display.

When all zones have been tested, the keypad will display:

Selected zones have been

Tested OK

Press OK or MENU

4.Press [OK] to save and exit, or press [MENU] to exit without saving.

System > System Testing >

This menu allows you to manually test the systems back up battery. The Solution 64 will automatically test the battery once per day and every time the system is armed.

The battery test can take up to two minutes to complete and the keypad will display the voltage of the battery during the test.

Enter programming mode (PIN + MENU) then,

1.Press [MENU] + [7] + [9] + [2].

The keypad will display the battery voltage whilst under test:

Battery test in progress.

Please wait..

Voltage = 13.4V

To Go Back Press OK

If the battery has passed the test, the keypad will display:

Battery test Passed.

Press OK to continue

If the battery has failed the test, the keypad will display:

Battery test Failed.

Please Call for Service.

Press OK to continue

2.Press [OK] to exit.

Solution 64 User Guide

EMAIL:

SERVICE

EMAIL:

MONITORED BY:

EMAIL:

WARRANTY EXPIRES:

NOTES:

Solution 64 User Guide

Bosch Security Systems

25 Huntingwood Drive

Huntingwood, NSW 2128

Australia

Phone: +612 9672 1777

Facsimile: +612 9672 1717

?? 2006 Bosch Security Systems

BLCC110U

920304

Issue FTR1.2