WELCOME/FEATURES

TERMINOLOGY

CONTROLS & FUNCTIONS

GETTING STARTED

Setting up the Phone

Installing the Beltclip

Optional Headset Installation

SETTING UP YOUR PHONE

Base Setup

Handset Setup

BASICS

Using Your Phone Call Waiting

Placing a Call on Hold

Adjusting the Ringer, and Earpiece and Speaker Volume

Muting the Ringer Mute Base Microphone Tone Dialing Switch-over Traveling Out of Range

Selecting a Different Channel Conferencing

Intercom

Contents

Welcome

Features

Congratulations on your purchase of the Uniden Cordless Telephone System! This is a ???Corded/Cordless??? Telephone unit. The corded handset (on base) can make/receive calls during power failure. You can now place a fully-featured cordless handset anywhere in your home or office where AC power is available to connect the handset charger.

Note: Illustrations in this manual are used for explanation purposes. Some illustrations in this manual may differ from the actual unit.

???5.8GHz Extended Range Technology

???Corded/Cordless Telephone System

???Make and Receive Calls During a Power Failure

???Integrated Answering Device

???Caller ID and Caller ID on Call Waiting

???50 Caller ID feature

???Dual Keypad and LCD Screen at Base

???10 Number Memory Dialing in the Base and Handset

???Trilingual Display Options and Voice Prompts (English, French and Spanish)

???Intercom Between Handset and Base

???Mute and Hold Features

???Do Not Disturb (DND) Feature

???Clock Display

???Base Speakerphone

1

1.Handset antenna

2.Beltclip hole

3.Jack for optional headset

4.Handset battery compartment

5.Handset earpiece

6.LCD display

7.call id (Caller ID)/menu (P.16, 35)

8./vol/ (volume & scroll) (P.16, 23) 14 9. /vol/ (volume & scroll) (P.16, 23)

31

32

33

34

35

43

44

45

46

47

52

36

53

54

21.memo/call rec (record) (P.46, 47)

22.Message LED

23.In use LED

24. (repeat/rewind) (P.44)

25.call id (P.35)

26. (play/stop) (P.44)

27.LCD display

28. (skip/forward) (P.45)

29.mem (memory) (P.29)

30. delete (P.30, 36, 45)

31.Corded base handset

32.Base speaker

33.answer on/off/answer on/off LED (P.41)

34.hold/hold LED (P.22)

35.mute/mute LED (P.24, 25)

36.Curl cord

37.find hs (handset)/intercom (P.27)

38.clock/menu (P.13, 39)

39.*/tone/ (left cursor) (P.25, 30)

40. / / /select/volume (volume, scroll & select) (P.13, 24, 35)

41.Mic (microphone)

42.#/ (right cursor)(P.30)

43.greeting (P.42)

44.do not disturb/do not disturb LED (P.24)

45.set (P.13, 39)

46.redial/pause (P.21, 31)

47.flash (P.22)

48. (speaker)/speaker LED (P.20, 26)

49.DC IN 9V Jack

50.TEL LINE Jack

51.Base attenna

52.Wall mount adapter

53.Charging contacts

54.Charge LED

55.DC IN 9V Jack

[ 5 ] C O N T R O L S & F U N C T I O N S

w w w . u n i d e n . c o m

Setting up the Phone

Do the following steps:

A.Choose the best location

B.Connect the base unit

C.Install the rechargeable battery pack into the handset

D.Connect the charger

E.Mount the base unit on a wall (if desired)

A. Choose the best location

Before choosing a location for your new phone, read ???Installation Considerations??? on page 59. Here are some important guidelines you should consider:

note

Keep the antenna free of obstruction.

D E T R A T S G N I T T E G

Avoid heat sources, such as radiators, air ducts, and sunlight

Avoid television sets and other electronic equipment

Avoid noise sources such as a window by a street with heavy traffic

Avoid microwave ovens

Avoid excessive moisture, extremely low temperatures, dust, mechanical vibration, or shock

note

???Use only the supplied [AD-830] AC adapter. Do not use any other AC adapter.

???Do not place the power cord where it creates a trip hazard or where it could become chafed and create a fire or electrical hazard.

B. Connect the base unit

1)Connect to the handset cord to the left side of the phone and the corded base handset.

2)Connect AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.

Connect the AC adapter to a continuous power supply (i.e., an outlet that is not controlled by a switch).

Place the base unit close to the AC outlet to avoid long extension cords.

3)Connect the telephone line cord to the TEL LINE jack and to a telephone outlet.

4)Set the base on a desk or tabletop. Place the corded base handset on the base.

If your telephone outlet isn't modular, contact your telephone company for assistance.

C. Install the rechargeable battery pack into the handset

1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.

2) Plug the battery pack connector (red & black wires) into the jack inside the battery compartment. (The connector notches fit into the grooves of the jack only one way.) Match the wire colors to the polarity label in the battery compartment, connect the battery and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on the battery wires. If the connection is secure, the battery jack will remain in place.

4) Place the battery case cover back on the handset and slide it upwards until it clicks into place.

note

Use only the Uniden (BT-905) rechargeable battery pack supplied with your cordless telephone.

D E T R A T S G N I T T E G

note

Use only the supplied

D. Connect the charger

The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the charger.

AC adapter (AD-310). Do not use any other AC adapter.

1)Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.

2)Set the charger on a desk or tabletop, and place the handset in the charger with the keypad facing forward.

3)Make sure that the charge LED illuminates.

If the LED does not illuminate, check to see that the AC adapter is plugged in and the handset makes good contact with the base charging contacts.

To AC outlet

AC adapter

(supplied)

To DC IN 9V

E. Mount the base unit on a wall (if desired)

Standard wall plate mounting

This phone can be mounted on any standard wall plate.

1) Remove the wall mount adapter from the base and snap it into the notches on the bottom of the base.

2) Plug the AC adapter to the DC IN 9V jack. 3) Wrap the AC adapter cord inside the

molded wiring channel as shown.

4) Plug the AC adapter into a standard 120V AC wall outlet.

5) Plug the telephone line cord into the TEL LINE jack.

6) Wrap the cord inside the molded wiring channel as shown.

7) Plug the telephone line cord into the telephone outlet.

8) Align the mounting slots on the base with the mounting posts on the wall.

Then push in and down until the phone is firmly seated.

9) On the base unit, pull the handset retainer

out of the slot. Rotate it clockwise 180 degrees. 10)Flip the retainer from front to back. Slide it back into the slot so that the lip of the retainer is up

and the oval is down. The retainer holds the handset in place.

w w w . u n i d e n . c o m

D E T R A T S G N I T T E G

G E T T I N G S T A R T E D [ 1 0 ]

Optional Headset Installation

Your phone may be used with an optional headset. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations. (Headsets may be purchased by visiting our website at www.uniden.com or by calling our Parts Department. See back cover page.)

w w w . u n i d e n . c o m

D E T R A T S G N I T T E G

G E T T I N G S T A R T E D [ 1 2 ]

???Press clock/menu on the base to access the base main menu.

???Use the volume up or down key ( / / /select/volume) to scroll through options.

6KOG

5GEWTKV[%QFG

4KPI6KOG

Setting the Dial Mode

Dial Mode sets the dial mode to tone or pulse. Most phone systems use tone dialing; the default setting is tone dialing. Set the dialing mode to match the dialing system used by your local phone service.

???If you are not sure of your dialing system, make a trial call. If the call connects, leave the setting as is; otherwise set the unit to pulse dialing.

???If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you may switch over to tone dialing (refer to ???Tone Dialing Switch- over??? on page 25).

note

E S

1)Press clock/menu and the volume down key to move the pointer to select Dial Mode, and then press set.

2)Press the volume up or down key to select Tone or Pulse (the initial setting is Tone).

3)Press set. You will hear a confirmation tone.

Setting Day and Time

Day & Time sets the day and time of your display.

1)Press clock/menu on the base.

2)Press set to select Time. The system announces ???Time???, the current time and the guidance for the setting the time.

&KCN/QFG

6QPG

2TGUUQTUGV

Use delete to edit

R U O Y P U G N I T T E N O H P

3)Press the volume up or down key to select the day of the week, and then press set.

4)Enter a two-digit number (01-12) to set hour, and then press set.

5)Enter a two-digit number (00-59) to set minute, and then press set.

6)Press the volume up or down key to choose AM or PM, and then press set. You hear a confirmation tone.

the hour and minute.

note

If the area code has already been stored in memory, the stored area code will be displayed. To change it, use

delete and number keys to enter the new

area code.

Setting the Area Code

If you enter a 3-digit area code number in the Area Code option, your local area code does not appear in the Caller ID message. For calls received from outside your local area code, you will see a full 10-digit number.

1) Press clock/menu and the volume down key on the base to select Area Code, and then press set.

2) Press the number keypad (0-9) to enter a 3-digit area code.

3)If you press set, the stored number will be transferred to the handset. If the transfer is successful, you will hear a confirmation tone from the base and handset. Otherwise, Area Code Setting Failed! appears on the display and an error tone sounds. You will have to start over with the procedure you are performing.

Setting Caller ID on Call Waiting (CIDCW)

Caller ID on Call Waiting (CIDCW) displays the name and number of an incoming call while you are on the line.

1) Press clock/menu and the volume down key on the base

2)Press the volume up or down key to select On or Off, and 2TGUUQTUGV then press set. You will hear a confirmation tone.

1)Press clock/menu and the volume down key on the base to select Language, and then press set.

2)Press the volume up or down key to choose English,

Fran ??? ais (French), or Espa ??? ol (Spanish). 3) Press set. You will hear a confirmation tone.

.CPIWCIG

'PINKUJ

2TGUUQTUGV

Handset Setup

Using the interface

Below are some tips for using the software interface on your phone.

O Y P U G N I T T E S E N O H P

???Press and hold call id/menu on the handset to access the main menu.

???Use the volume up key or volume down key ( / /vol/ ) to scroll through options.

#WVQ6CNM1HH

.CPIWCIG'PI

#TGC%QFG

R U

1)Press and hold call id/menu on the handset. Press select/int???com to turn AutoTalk on.

2)Press end. The handset returns to standby mode.

Selecting a Language (Handset only)

#WVQ6CNM1HH

.CPIWCIG'PI

#TGC%QFG

1)Press and hold call id/menu on the handset.

2)Press the volume down key to move the pointer to select

Language.

3)Press select/int???com to select from Eng (English), Fr. (French), Esp (Spanish).

4)Press end. The handset returns to standby mode.

#WVQ6CNM1P

.CPIWCIG'PI

#TGC%QFG

3) Press talk/flash.

From the base

1)Pick up the corded handset, or press (speaker).

2)Listen for the dial tone.

3)Dial the number.

OR

1)Dial the number.

If a pause is required, press redial/pause.

2)Pick up the corded handset, or press (speaker).

Receiving a call

From the handset

1)Remove the handset from the cradle. (If AutoTalk is on, the phone will automatically answer the call when you pick it up.)

2)Press talk/flash.

OR

If the handset is off the cradle, press talk/flash or any number. (AutoTalk is on.)

From the base

Press (speaker) or pick up the corded handset.

note

???To set ???AutoTalk???, see page 17.

???The base microphone is located under the base. Position yourself as near to the base as possible.

S C I S A B

Call Waiting

If you have Call Waiting service, you can receive calls while on the line.

1) If a call comes in while you are on the phone, you will hear a call waiting tone. If you have CIDCW activated, you will see the name and number of the incoming caller.

2)Press talk/flash on the handset, or flash on the base

to accept the waiting call. After a short pause, you will hear the new caller.

3)To return to the original caller, press talk/flash on the handset, or flash on the base again.

You must subscribe through your local telephone company to receive Call Waiting service.

Placing a Call on Hold

1)During a call with the base, press hold on the base. The call will be put on hold.

2)To return to the call, press hold again, pick up the corded handset or press talk/flash on the handset. To talk to the caller on a speakerphone, press

(speaker) or hold on the base.

w w w . u n i d e n . c o m

note

???You can place a call on hold for ten minutes. When ten minutes has passed, the call is disconnected, and the phone returns to standby mode.

hold, and the call will remain on hold.

B A S I C S [ 2 2 ]

Earpiece and Speaker Volume

You can select earpiece volume from among four volume levels on the handset and the corded handset and eight different volume levels on the base speaker. For the base speaker volume, press the volume up key or volume down key ( / /vol/ or

// /select/volume) during a call or while the speaker is turned on to change the earpiece/speaker volume level. This setting will remain in effect after the telephone call has ended.

Muting the Ringer

Do Not Disturb (DND)

The do not disturb feature (DND) allows you to mute the ringer on the base and handset at the same time. The phone must be in standby mode. Press and hold do not disturb on the base. You will hear a confirmation tone, and the do not disturb LED illuminates on the base. Do Not Disturb flashes on the handset display. To cancel the DND feature, press do not disturb again. You can also mute the ringer tone while the phone is ringing by pressing do not disturb on the base.

Temporarily Muting the Ringer

To mute the ringer tone temporarily for the handset or the base, when the phone is ringing, press end on the handset when the handset is off the cradle, or press

(play/stop) or mute on the base. The mute will last for the current incoming call only. The ringer tone will return to the previous setting starting with the next incoming call.

note

If the answering system is off and press do not disturb, the answering system will be automatically turned on.

S C I S A B

note

Mute Base Microphone

During a call or an intercom call, press mute on the base to mute the microphone. Mute On appears on the display. To cancel muting, press mute again.

522JQPG

/WVG1P

The tone feature only applies when the dial mode is set to pulse.

Tone Dialing Switch-over

If your telephone company requires pulse dialing, you can switch over to tone dialing after the call connects. This feature is useful when you need tone dialing to use any automated menu systems, such as telephone bank tellers, telephone prescription refills, customer support menus, etc.

If your phone is set to pulse dialing mode, make your call normally. Once your call connects, press */tone/ . Any digits you enter from then on will be sent as tone digits. When this particular call ends, the phone automatically returns to pulse dialing mode.

Traveling Out of Range

During a call, as you begin to move your handset too far from your base unit, noise may increase. If you pass the range limits of the base unit, your call will terminate within one minute.

Selecting a Different Channel

If you encounter interference while using your handset, you can manually change the handset???s channel for clear operation. While using your handset, press delete/channel. Scanning appears on the display, indicating the handset is changing to another channel. For more information on interference, refer to ???Precautions??? on page 59.

Conferencing

Up to three people can participate in a conference call using an outside line, the handset, and the base.

Joining a Conference Call

You can easily join a call already in progress.

From the base

1) While in talk mode with the handset, press (speaker) on the base or pick up the corded handset from the base to join the conference call.

2) To hang up, press (speaker) or return the corded handset to the base. The handset will still be connected to the call.

From the handset

1) While in talk mode with the base, press talk/flash on the handset to join the call.

2) To hang up, return the handset to the cradle or press end on the handset. The base will still be connected to the call.

note

???You can record a conference call. For details, please see ???Recording a conversation??? on page 47.

???During a conference call with the handset, you can receive a waiting call by pressing talk/flash on the handset.

S C I S A B

note

???If the party is busy or out of range, the handset returns to standby mode.

???If the party does not answer within one minute, the operation is canceled.

Intercom

The intercom feature lets you communicate between the handset and base without using the phone line.

Making an Intercom Page

From the handset

1)With the phone in standby mode, press select/int???com.

2)The base will be paged. An intercom tone sounds.

From the base

1)With the phone in standby mode, press find hs/intercom on the base.

2)The handset will be paged. An intercom tone sounds.

To cancel intercom, press find hs/intercom or (speaker). 2CIKPI*CPFUGV

Making an Intercom Page While the Line is on Hold

You can make an intercom call while an outside caller is on hold; making an intercom call will not terminate the call on hold.

From the handset

1)During a call, press select/int???com on the handset.

2)The call will automatically be placed on hold, and the paging tone sounds. To cancel the page, press talk/flash, or select/int???com.

From the base

1)During a call, press hold on the base. The call will be put on hold.

2)Press find hs/intercom. The paging tone sounds.

3)To cancel the page from:

--Speakerphone: press (speaker) or find hs/intercom.

--Corded base: press find hs/intercom.

Answering an Intercom Page

From the handset

1)Pick up the handset from the cradle. (If AutoTalk is enabled, the handset will automatically answer when you pick it up.)

2)Press talk/flash or select/int???com.

OR

1)If the handset is off the cradle, press talk/flash, select/int???com or any number key (AutoTalk is on.)

From the base

Pick up the corded handset. To answer with the base speakerphone, press

(speaker), or find hs/intercom. To hang up an intercom page:

--From the handset: press end, select/int???com or return the handset to the cradle.

--From the base: with the base speakerphone, press find hs/intercom or

(speaker).

With the corded base handset, return the corded handset to the base.

S C I S A B

note

When editing the speed dial memory, you must press a key within 30 seconds or the phone will return to standby mode.

Using the Speed Dial Memory

The speed dial memory allows you to store up to 10 names and numbers in the handset and base. The speed dial memory is stored independently in the base and handset. You can store up to 10 numbers in the base and up to 10 numbers in the handset. You can dial these numbers with just a few key presses.

The speed dial memory is not limited to phone numbers. You can store any number (up to 20 digits) that you need to enter once your call connects. This is referred to as Chain Dialing. For example, you can save your bank account number to speed dial memory. When you call your bank's telephone teller service and are prompted to enter your account number, simply press memory (mem on the base) and the speed dial number where you stored your account number. Then press select/int???com (set on the base).

Storing Names and Numbers in Speed Dial Memory

1) With the phone in standby mode, press memory (mem on the base).

2)Enter 0-9 to select the speed dial number where you would like to store this entry. You can also scroll through the list with the volume up or down key

(// /volume or / / /select/volume). Press select/int???com (set on the base) twice.

3)Store Name appears and a cursor flashes indicating that

the display is ready for the name to be entered.

If the selected speed dial number is already assigned, the Edit screen appears. You can select Edit to edit this entry, select Delete to erase this entry, or select Go Back to choose another speed dial number.

4)Enter a name according to the instructions below.

???The name can be up to 14 characters.

??? Press and hold delete/channel ( delete on the base) to delete all the characters.

??? If no name is required, go to step 5.

Refer to the letters on the number keys to select the desired characters.

Each time you press a numeric key, the displayed character appears in the following order: Upper case letters first, lower case letters next and finally the number corresponding to the key.

If you make a mistake while entering a name

Use */tone/ or #/ to move the cursor to the incorrect character.

Press delete/channel ( delete on the base) to erase the wrong character. Then enter the correct character. To delete all characters, press and hold delete/channel

( delete on the base).

note

If the next character uses the same number key, you must press the #/ key to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.

D E E P S E H T G N I S U Y R O M E M L A I D

For example, to enter Movies.

1)Press 6. Then press #/ to move the cursor to the right.

2)Press 6 six times.

3)Press 8 six times.

4)Press 4 six times.

5)Press 3 five times.

6)Press 7 eight times.

8) Press end ( (play/stop) on the base) to exit memory setup mode. The phone returns to standby.

Storing Caller ID data in Speed Dial Memory

Data (Caller ID names/numbers) shown in the Caller ID list can be stored in memory dialing. For instructions on viewing the Caller ID data, see page 35.

1)Press call id/menu (call id on the base). Select the phone number to be stored from the Caller ID list by

pressing the volume up or down key ( / / /volume or / / /select/volume).

2)Press memory (mem on the base).

3)Enter a number (0 - 9) or press the volume up or down

key (// /volume or // /select/volume) to select the memory location to be stored.

4)Press select/int???com (set on the base). You hear a confirmation tone, and the number is stored in memory. The display returns to the Caller ID data.

note

You can not store a Caller ID message if no phone number appears in the message.

D E E P S E H T G N I S U Y R O M E M L A I D

note

If you want to directly access the speed dial location, press and hold 0-9 in standby mode, and then press

talk/flash

( (speaker) on the base) or remove the corded handset from the base.

If a message has already been stored in the selected memory number location, a confirmation screen is displayed. Press the volume up key ( / /volume or

/ /select/volume) to select Yes. Press select/int???com

(set on the base) to overwrite. The display returns to the Caller ID data.

Making Calls from Speed Dial Memory

1) Press memory (mem on the base). The handset or base displays your programmed speed dial number.

2)Enter the number (0 - 9), or press the volume up or down

key (/ / /volume or / / /select/volume) to select the speed dial number you would like to dial.

3)Press talk/flash ( (speaker) on the base) or remove

the corded handset from the base. Then the displayed number is dialed.

To cancel speed dialing

Press end ( (play/stop) on the base) to cancel speed dialing. The phone returns to standby mode.

Also, if the phone is idle (e.g., no key is pressed) for 30 seconds, the phone returns to standby mode.

Caller ID and Caller ID on Call Waiting (CIDCW)

You must subscribe to Caller ID service through your local telephone provider to use this feature. When the telephone rings, the Caller ID feature allows you to view the caller???s name, phone number, date and time of call. The Caller ID data stores information for up to 50 incoming calls - even unanswered calls. With Caller ID on Call Waiting (CIDCW), you will hear a Call Waiting tone while you are on a call, and the Caller ID data is displayed. To accept the waiting call, press talk/flash (flash on the base) (see page 22).

Additionally, you can dial a number stored in the Caller ID list or save data to your Memory dial list.

When the Telephone Rings

When the Caller ID data is received, each the handset and base shows the caller???s phone number along with the date and time. The incoming call information is stored in the Caller ID record on both the handset and base. If the Caller ID service includes the caller???s name, the caller???s name appears on the display (up to 15 letters).

The date and time received

Caller's name

Caller's phone number

You may receive any one of the following messages:

When invalid data is received;

When a private name is received;

When a private number is received;

When a unknown name is received;

When a unknown number is received;

note

???If you answer a call before the Caller ID data is received (for example, before the second ring), the Caller ID data will not appear.

???When the call is received via a telephone company that does not offer Caller ID service (including international calls), the caller???s phone number and name do not appear.

???When the call is via a private branch exchange (PBX), the caller's phone number and name may not appear.

D I R E L L A C

note

???In Caller ID operation, if no key is pressed for more than 30 seconds, an error tone sounds and the telephone returns to standby mode.

???Each data can be up to 15 characters for the name and 15 digits for the phone number.

???The number of calls from the same Caller ID appears next to the received time. Once you view the new data, the number will be cleared.

Data errors appear as "???."

Viewing the Caller ID Data

1) With the phone in standby mode, press call id/menu (call id on the base).

The summary screen appears. The screen shows the number of new messages and total messages.

2) To view the Caller ID data in historical order (from new to

old or from old to new), use the volume down key (/

/volume or / /select/volume) to scroll through the data from the latest to the earliest, or the volume up key ( / /volume or

/ /select/volume) to scroll back through the messages.

3) To finish the viewing operation:

From Handset - press end.

From Base - press (play/stop).

Deleting Data from the Caller ID List

The cordless phone stores up to 50 Caller ID names/numbers. If the phone receives the 51st Caller ID, the oldest one in the list is automatically deleted. Caller ID data can also be deleted manually.

Deleting a Caller ID Data

1)Press call id/menu (call id on the base) in standby mode. Find the message to be deleted from the Caller ID list by

pressing the volume up key or the volume down key

( / / /volume or / / /select/volume).

2)Press delete/channel ( delete on the base).

3)Press the volume up key or the volume down key

(// /volume or // /select/volume) to select Yes, and then press select/int???com (set on the base).

Deleting all Caller ID names/numbers

1) With the phone in standby mode, press call id/menu (call id on the base).

2) Press delete/channel ( delete on the base).

w w w . u n i d e n . c o m

note

???While using the

Delete All? or Delete Message?

screen, if no key is pressed for more than 30 seconds, an error tone sounds, and the phone returns to standby mode.

???If you get an incoming call or intercom page, the deleting operation is canceled, and you can answer the call or intercom page.

C A L L E R I D [ 3 6 ]

D I R E L L A C

The Integrated Answering Device

The phone has a built-in answering system that answers and records incoming calls. You can also use your answering system to record a conversation, leave a voice memo message, or announce a special outgoing message to callers when you're away from your phone.

Features

???Digital Tapeless Recording

???Up to 13 minutes of Recording Time

???Call Screening

???Personal or Prerecorded Outgoing Messages

???Trilingual Display Options and Voice Prompts (English, Spanish, or French)

???Time and Day Announcement

???Remote Message Retrieval

???Toll Saver

???Conversation Recording

???Voice Memo

???Message Alert On/Off

???Retrieve TAD Messages using Handset

D E AT R G E T N I E H T E C I V E D G N I R E W S N A

note

???For your convenience, voice prompts will guide you through the menu mode.

Setting Up the Answering Machine

Setting the Record Time

Record Time sets the duration for recording the incoming messages. You have three record time options. The options 1 Minute or 4 Minutes set the duration for recording the incoming messages. Announce only answers the call but prevents the caller from leaving a message.

???Press clock/menu or

(play/stop) on the base to return to standby mode.

???If you do not press a key within 30 seconds, the phone will time out and exit the menu

1)Press clock/menu and the volume down key on the base to select Record Time, and then press set.

2)Press the volume up or down key to select Record Time

1 Minute, 4 Minutes, or Announce Only.

3)Press set. You will hear a confirmation tone.

Setting the Call Screen

4GEQTF6KOG

/KPWVG 2TGUUQTUGV

mode.

Call Screen allows you to listen to the incoming message being left by the caller before you answer the call.

1)Press clock/menu and the volume down key on the base to select Call Screening, and then press set.

2)Press the volume up or down key to select On or Off.

3)Press set. You will hear a confirmation tone.

%CNN5ETGGPKPI

1P 2TGUUQTUGV

1)Press clock/menu and the volume down key on the base to select Ring Time, and then press set.

2)Press the volume up or down key to select a Ring Time

(Toll Saver, 2 Times, 4 Times, or 6 Times).

3)Press set. You will hear a confirmation tone.

Setting the Message Alert On or Off

4KPI6KOG

6QNN5CXGT 2TGUUQTUGV

1)Press clock/menu and the volume down key on the base to select Message Alert, and then press set.

2)Press the volume up or down key to select On or Off.

3)Press set. You will hear a confirmation tone.

/GUUCIG#NGTV

1HH 2TGUUQTUGV

E T N I E H T N I R E W S N A

Turning the message alert tone off by pressing any key

To quickly turn off the Message Alert tone, press any key on the base unit; the tone will automatically deactivate.

D E AT R G E C I V E D G

note

Setting a Security Code (PIN Code)

Security code selects a two-digit Personal Identification Number (PIN) code. A PIN code is required to play your messages from a remote location.

1)Press clock/menu and the volume down key on the base to select Security Code, and then press set.

2)Enter a two-digit PIN code (01-99) using the number keypad. To change the number, use delete to backspace.

3)Press set. You will hear a confirmation tone.

5GEWTKV[%QFG



2TGUUQTUGV

When the answering system is full, FL appears on the LCD. You should delete some messages so that the system can record new messages.

Turning the Answering System On/Off

1) To turn the answering system on, press answer on/off on the base when the phone is in standby mode.The answer on/off LED will be illuminated. If the message LED flashes, then there are new messages waiting for you.

2) To turn the answering system off, press answer on/off on the base. The answer on/off LED will no longer be illuminated. To turn theanswering system back on,

press answer on/off.

Setting Your Outgoing Message (Greeting)

When you receive a call, the answering system automatically plays either the pre- recorded message or your own greeting.

The following message is pre-recorded: ???Hello, no one is available to take your call. Please leave a message after the tone.???

Record a Personal Outgoing Message

Record Greeting allows you to record a personal outgoing message (greeting) which the answering system automatically plays when you receive a call.

1) Press greeting. While the pre-recorded message is playing, press and hold greeting again.

You hear the announcement ???Record greeting??? and a confirmation tone.

If your own greeting has already been recorded, delete the

current message and then record a new greeting again. While the current personal outgoing message is playing, press delete. And then start over with the first.

2)Start recording your message. You have 30 seconds, and the message counter starts to count down.

3)When you are finished recording your greeting, press greeting, (play/stop) or set. You hear a confirmation tone, and then your greeting plays back for you.

note

???Position yourself as near to the base as possible and speak clearly when recording your outgoing message.

???If you make an outside call or a call is received during the operation, the operation is canceled.

???The greeting must be more than two seconds long, or it will not be recorded.

???To delete the personal outgoing message,

press delete while the message is playing. The system announces ???Greeting has been deleted.???

D E AT R G E T N I E H T C I V E D G N I R E W S N A

E

Playing your messages

1)With the phone in standby mode, press (play/stop).

The system announces the number of new and old messages while the message counter displays only the number of new messages. The time and day that each message was received is announced after the message is played. The message counter will then display the number of current stored messages.

2)When all new messages have been played, you hear a confirmation tone, and the system announces ???End of messages.??? The system returns to standby.

3)After you have reviewed your new messages, you can play your old messages by pressing

(play/stop) again. Once you have listened to a new message, it then becomes an old message. The old messages will be played in the order in which they were received.

Repeating a message

1)Press (play/stop) to review your messages. The number of stored messages is announced.

2)To repeat the current message, press (repeat/rewind) after a few seconds of beginning the message. To quickly scroll backwards through a message, press and

hold (repeat/rewind). To repeat the previous message, press

(repeat/rewind) within about four seconds after a message begins playing. If you have several messages, press (repeat/rewind) repeatedly until you return to the message you want to replay. If the current message is the first new message, the system plays back from the beginning of the current message (it does not go back into the old message group).

3)Press (play/stop) at any time to stop reviewing messages and return to standby. The message counter shows the number of messages stored in memory.

D E AT R G E T N I E H T E C I V E D G N I R E W S N A

Voice memo

The voice memo function allows the user to record messages (more than two seconds and less than four minutes).

1)With the phone in standby mode, press and hold memo/call rec on the base.

2)You will hear the announcement ???Record Memo Message??? and a confirmation tone.

3)Start your recording.

4)When you have finished, press (play/stop), memo/call rec or set to stop recording. The system returns to standby.

note

???The voice memo messages are recorded as an incoming messages.

???When the answering system is full, FL appears on the display, and the system returns to standby.

D E AT R G E T N I E H T E C I V E D G N I R E W S N A

note

???If the recording memory is full, you can not record a conversation until you clear some messages from the memory.

???Every state has different regulations governing the recording of conversations over the telephone. Make sure to check your local, state and federal laws before using this product to record any telephone conversation in order to determine that your use is in compliance with such laws or guidelines.

???You can not record intercom conversations.

???To activate this feature, you must turn the Call Screen feature on. See ???Setting the Call Screen??? on

page 39.

Recording a conversation

You can record a conversation from the handset or the base (more than two seconds and less than ten minutes).

1)During a conversation, press rec/remote/call screen on the handset or press and hold memo/call rec on the base.

2)Recording a Call appears on the display. A confirmation tone that can be heard by both parties sounds during recording.

3)To stop recording, press rec/remote/call screen on the handset, or memo/call rec or (play/stop) on the base.

Screening a call

From the base

To screen an incoming call, use the following steps:

1)After the answering system answers, the base speaker will let you hear the calls as the machine records the message. To adjust the volume, press the volume up or down key. If you turn the answering system off, you cannot screen a call.

2)To answer the call, pick up the corded handset or press (speaker) on the base.

To mute the Call Screen, press mute or (play/stop). To cancel muting, press /

/ /select/volume.

From the handset

Press rec/remote/call screen when the system is answering. To cancel the Call Screen, press end or return the handset to the cradle. To answer the call, press talk/flash or any number (when AutoTalk is set to on). The answering system will disconnect automatically.

Remote Operation

You can operate your answering system from a remote location (when you are away from home, or from another room using the handset). Use this function to check for recorded messages, to play or delete message. When using any touch-tone telephone, you can even record a new greeting message.

Remote access with any touch-tone telephone

You can operate your answering system from a remote location using any touch-tone telephone.

1)Call your telephone number.

2)During the greeting message, press 0 and enter your PIN code (see page 41).

3)The answering system announces the current time and the number of messages stored in memory. Then you hear ???To play incoming messages, press zero two. For help, press one zero.???

4)You may continue to listen to the voice prompts, or you may select a command from the chart on the next page:

For your convenience remote operation cards are provided for you to use while away from home (located on page 62).

note

Once you enter the remote access menu, you must enter a command within 15 seconds, or the answering system automatically hangs up and returns to standby.

D E AT R G E T N I E H T C I V E D G N I R E W S N A

E

Turn on the Answering System Remotely

If you have forgotten to turn on your answering system, you can turn it on remotely from any touch-tone telephone.

1)Call your telephone number.

2)Wait ten rings until the system answers. You hear intermittent beeps.

3)Press 0 and then enter your PIN code. The answering system announces the number of messages stored in memory. You hear ???To play incoming messages, press zero two. For help, press one zero.???

4)Press 0 then 6 to turn the answering system on. You hear the outgoing message and a confirmation tone.

5)Hang up the phone; subsequent calls will be answered by the system.

Remote Access with the Handset

You can operate your answering system from another room using a handset.

1) With the phone in standby mode, press rec/remote/call screen on the handset. Remote AnsweringMachine operation appears on the display. The answering system announces the current time and the number of messages stored in the memory.

2)You hear ???To play incoming message, press two. For help, press zero??? followed by intermittent beeps.

D E AT R G E T N I E H T E C I V E D G N I R E W S N A

Note on Power Sources

Power Failure

During the period that the power is off, you can make or receive calls with the base. You cannot use the base speaker phone or the cordless handset.

Low battery alert

When the battery pack is very low and needs to be charged, the handset is programmed to eliminate functions in order to save power. If the handset is not in use, Low Battey appears on the handset LCD and none of the handset keys will operate.

If the phone is in use, Low Battery flashes and the handset beeps. Complete your conversation as quickly as possible and return the handset to the cradle for charging.

Information stored in the phone's memory will be retained for 30 minutes after the battery pack is removed. This includes earpiece volume, ringer tone and volume and last number dialed.

Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum performance, be sure to return the handset to the cradle after a telephone call.

Battery replacement and handling

When the operating time becomes short even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. A replacement battery may be purchased by calling Uniden's Parts Department (see back cover page).

L A N O I T I D D A N O I T A M R O F N I

General Information

The phone complies with FCC Parts 15 and 68.

Operating temperature: -10 ??C to +50 ??C (+14 ??F to +122 ??F)

???To avoid damage to the phone use only Uniden AD-830, AD-310 and BT-905 with your phone.

???If the handset is left off of the cradle, the actual Talk mode duration will be reduced respective to the amount of time the handset is off the cradle.

Recharge your phone on a regular basis by returning the handset to the cradle after each phone call. When the operating time becomes short, even after the battery is recharged, please replace the battery. With normal usage, the battery should last about one year.

A replacement Uniden adapter or battery may be purchased by calling Uniden's Parts Department (see back cover page).

Specifications, features, and availability of optional accessories are all subject to change without prior notice.

L A N O I T I D D A N O I T A M R O F N I

Precautions!

Before you read anything else, please observe the following:

Warning!

Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.

Rechargeable Nickel-Cadmium Battery Warning

???This equipment contains a rechargeable nickel-cadmium battery.

???Cadmium is a chemical known to the State of California to cause cancer.

???The rechargeable nickel-cadmium battery contained in this equipment may explode if disposed of in a fire.

???Do not short-circuit the battery.

???Do not charge the rechargeable nickel-cadmium battery used in this equipment in any charger other than the one designed to charge this battery as specified in the owner??fs manual.

Using another charger may damage the battery or cause the battery to explode.

Rechargeable Nickel-Cadmium

Batteries Must Be Recycled or

Disposed of Properly

???Uniden voluntarily participates in an RBRC???

industry program to collect and recycle nickel-cadmium batteries at the end of their useful life, when taken out of service within the United

States.

The RBRC??? program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste stream, which is illegal in some areas.

???Through the RBRC??? program, Uniden makes it easy for you to drop off the used battery at local retailers of replacement nickel-cadmium batteries. You may also contact your local recycling center for information on where to return the used battery. Pleas e call 1-800-8- BATTERY for information on Ni-Cd battery recycling in your area. Uniden's involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

???RBRC??? is a registered trademark of the Rechargeable Battery Recycling Corporation.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Uniden works to reduce lead content in our PVC coated cords in our products and accessories.

Warning!

The cords on this product and/or accessories contain lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

Important Safety Instructions

When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without liquid or aerosol cleaners.

4.Do not use this product near water; for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

5.Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the unit.

6.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered.

This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be damaged by persons walking on it.

9.Do not overload wall outlets and extension cords, as this can result in the risk of fire or electrical shock.

10.Never push objects of any kind into this product through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

11.To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.

12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A.When the power supply cord is damaged or frayed.

B.If liquid has been spilled into the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate normally when following the operating instructions. (Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive repair work by a qualified technician.)

E.If the product has been dropped or the cabinet has been damaged.

F.If the product exhibits a distinct change in performance.

13.Do not use the telephone to report a gas leak in the vicinity of the leak.

Additional Battery Safety Precautions

Caution! To reduce the risk of fire or injury to persons by the battery, read and follow these instructions:

1.Use only the Uniden battery pack specified in the owner's manual.

2.Do not dispose of the battery pack in a fire. The cell may explode. Check the Nickel Cadmium battery disposal package insert for disposal instructions.

3.Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

4.Exercise care in handling the battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

5.Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the owners manual provided for this product.

6.Observe proper polarity orientation between the battery pack and battery charger.

7.Batteries must be disconnected and removed from the product before shipment to prevent accidental operation during transport. Any batteries transported with the product must be separately secured and cushioned with any exposed terminals covered to prevent their breakage, leakage, movement within the packaging, or short circuits. Failure to follow these recommendations for shipment may result in serious damage and/or personal injury during transport and may be against the U.S. Department of Transportation (DOT), International Civil Aviation Administration (ICAO), International Air Transport Association

(IATA), and/or the International Maritime Organization (IMO) regulations.

SAVE THESE INSTRUCTIONS!

Important Electrical Considerations

Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiringand damage any device connected to it. This phone is no exception.

The FCC Wants You To Know

Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by the owner's manual, could void your authority to operate this product. Your telephone complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN to your telephone company. Both numbers are on the base unit.

Note: You must not connect your phone to:

???coin-operated systems

???most electronic key telephone systems

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications, may not be ensured when using this phone.

S N O I T U A C E R P Y T N A R R A W

w w w . u n i d e n . c o m

P R E C A U T I O N S & W A R R A N T Y [ 5 8 ]

&

To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy various products may produce depending on their intended usage. This product has been tested and found to comply with the FCC's exposure criteria. For body worn operation, the FCC RF exposure guidelines were also met when used with the Uniden accessories supplied or designed for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines and should be avoided.

Range

Your new phone is designed to achieve the maximum possible range by transmitting and receiving according to the highest specifications set forth by the FCC. We have rated this phone to operate at a maximum distance with the qualification that the range depends upon the environment in which the telephone is used. Many factors limit range, and it would be impossible to include all the variables in our rating. The Maximum Range rating of this phone is meant to be used as a means of comparison against other range claims.

Telephone Line Problems

The FCC has granted the telephone company the right to disconnect service in the event that your phone causes problems on the telephone line. Also, the telephone company may make changes in facilities and services which may affect the operation of your unit. However, your telephone company must give adequate notice in writing prior to such actions to allow you time for making necessary arrangements to continue uninterrupted service. If you are having trouble with your telephone service, you must first disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it disconnected until the trouble has been corrected.

Radio Interference

Radio interference may occasionally cause buzzing and humming in your cordless handset, or clicking noises in the base. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too distracting, please check around your home to see what appliances may be causing the problem. In addition, we recommend that the base not be plugged into a circuit that also powers a major appliance because of the potential for interference. Be certain that the antenna on the unit is fully extended when needed.

In the unlikely event that you consistently hear other voices or distracting transmissions on your phone, you may be receiving radio signals from another cordless telephone or other source of interference. If you cannot eliminate this type of interference, you need to change to a different channel.

Finally, it should be noted that some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference.

More than One Cordless Telephone

If you want to use more than one cordless telephone in your home, they must operate on different channels. Press the channel key to select a channel that provides the clearest communication.

Cordless Telephone Privacy

Cordless telephones are radio devices. Communications between the handset and base of your cordless telephone are accomplished by means of radio waves which are broadcast over the open airways.

Because of the inherent physical properties of radio waves, your communications can be received by radio receiving devices other than your own cordless telephone unit. Consequently, any communications using your cordless telephone may not be private.

Installation Considerations

Selecting a Location

Before choosing a location for your new phone, there are some important guidelines you should consider:

???The location should be close to both a phone jack and continuous power outlet. (A continuous power outlet is an AC outlet which does not have a switch to interrupt its power.)

???Keep the base and handset away from sources of electrical noise such as motors or fluorescent lighting.

???Be sure there is sufficient space to fully extend the base antenna.

???The base can be placed on a desk or tabletop or mounted on a standard telephone wall plate.

???You should charge your new phone for 15-20 hours before completing the installation or using the handset.

Telephone Line Outlets

There are two types of phone outlets:

Modular Jack

Most phone equipment available now uses modular jacks. Phone cords are fitted with a molded plastic connector which plugs into this type of jack. If you do not have modular phone jacks, contact your local telephone company for information about their installation.

Hardwired Jack

Some equipment is wired directly to a phone jack, and these types of installations require a modular jack converter. This type of installation is not difficult; however, you should contact your Uniden telephone dealer or a telephone supply store for advice about the proper adapter or converter for your particular situation.

Connecting the Telephone Cords

Consider these safety guidelines before connecting the telephone cords: Caution!

???Never install telephone wiring during a lightning storm.

???Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected.

???Use caution when installing or modifying telephone lines.

Applying Power to the Base

This phone requires an AC outlet, without a switch to interrupt power, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, wrap the power cord around the strain relief notch on the bottom of the base.

NOTE: Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards.

One Year Limited Warranty

Important: Evidence of original purchase is required for warranty service.

WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF

WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.

WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is

(A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH

ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT

AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE

WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF

LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS

WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:

Uniden America Corporation

Parts and Service Division

4700 Amon Carter Blvd.

Fort Worth, TX 76155

I.C. Notice

TERMINAL EQUIPMENT

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.

This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

RADIO EQUIPMENT

The term ???IC:??? before the radio certification number only signifies that Industry Canada technical specifications were met.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ???Privacy of communications may not be ensured when using this telephone???.

E C I T O N . C . I

Index

A

Announce only feature . . . . . . . . .43 Answering system

Deleting a message . . . . . . . . . . 45 Playing your messages . . . . . . .44 Recording a conversation . . . . . 47 Remote access . . . . . . . . . . . . . 48 Repeating a message . . . . . . . . 44 Skipping a message . . . . . . . . . 45 Turning On/Off . . . . . . . . . . . . 41

Area Code . . . . . . . . . . . . . . . . . .15 AutoTalk . . . . . . . . . . . . . . . . . . 17

B

Battery

Preparing and charging . . . . . . . .8

Replacement and handling . . . . . 52

Beltclip . . . . . . . . . . . . . . . . . . .11

C

Caller ID

Caller ID services . . . . . . . . . . . 34

Calling . . . . . . . . . . . . . . . . . . 37

CIDCW . . . . . . . . . . . . . . . . . . 34

Deleting . . . . . . . . . . . . . . . . . 36

Setting . . . . . . . . . . . . . . . . . .15

Viewing . . . . . . . . . . . . . . . . . 35

Clock . . . . . . . . . . . . . . . . . . . . .14

Conferencing . . . . . . . . . . . . . . . 26

Contrast . . . . . . . . . . . . . . . . . . . 13

D

Dial mode . . . . . . . . . . . . . . . . . 14

E, F, G, H

Earpiece volume . . . . . . . . . . . . . 24 General information . . . . . . . . . . . 54 Headset installation . . . . . . . . . . 12 Hold . . . . . . . . . . . . . . . . . . . . . 22

I, J, K, L

I.C. notice . . . . . . . . . . . . . . . . . 60 Important safety instructions . . . . 58 Intercom . . . . . . . . . . . . . . . . . . 27 Language . . . . . . . . . . . . . . . . . . 17 Liquid damage . . . . . . . . . . . . . . 57

M, N, O

Making a call . . . . . . . . . . . . . . . 19 Mute . . . . . . . . . . . . . . . . . . . . . 25 Outgoing message . . . . . . . . . . . . 42

P, Q

Precautions . . . . . . . . . . . . . . . . 58

R

Receiving a call . . . . . . . . . . . . . 20 Remote . . . . . . . . . . . . . . . . . . . 48 Remote access

away from home . . . . . . . . . . . 48 from your handset . . . . . . . . . . 50

Ringer

Adjusting . . . . . . . . . . . . . . . . 23 Do not disturb . . . . . . . . . . . . . 24 Mute . . . . . . . . . . . . . . . . . . . 24

S

Setting up

base unit . . . . . . . . . . . . . 13, 39 Handset . . . . . . . . . . . . . . . . . 16 Speed dialing . . . . . . . . . . . . . . . 29

T, U, V, W, X, Y, Z

Talk and Standby Times . . . . . . . . . 3 Troubleshooting . . . . . . . . . . . . . 55 Voice memo . . . . . . . . . . . . . . . . 46 Warranty . . . . . . . . . . . . . . . . . . 59

Remote Operation Card

C U T

REMOTE OPERATION CARD

C U T

MEMORY LOCATION MEMO

Remote access away from home

1.Call your phone number from a touch-tone phone.

2.During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. The phone stands by for you to enter a command.

3.To quit, hang up the phone.

Turn on the answering system remotely

1.Call your phone and let it ring 10 times until it answers.

2.Press 0 and enter your PIN code.

3.Press 0 then 5 to stop the announcement.

4.Press 0 then 6 to turn the answering system on.

1*

2

3

4

5

E R T A R E P O

C U T

REMOTE OPERATION CARD

C U T

MEMORY LOCATION MEMO

T O M N O I

Remote access away from home

1.Call your phone number from a touch-tone phone.

2.During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. The phone stands by for you to enter a command.

3.To quit, hang up the phone.

Turn on the answering system remotely

1.Call your phone and let it ring 10 times until it answers.

2.Press 0 and enter your PIN code.

3.Press 0 then 5 to stop the announcement.

4.Press 0 then 6 to turn the answering system on.

1*

2

3

4

5

E D R A C

w w w . u n i d e n . c o m

R E M O T E O P E R A T I O N C A R D [ 6 2 ]

Remote Operation Card

C U T

MEMORY LOCATION MEMO

Need a Part?

To order headsets, additional handsets, our website at www.uniden.com or call

replacement batteries or other accessories, visit 1-800-554-3988, Mon-Fri, 8 a.m. to 5 p.m. CST.