Model 1360
Call Waiting / Caller ID Speakerphone with 12 Number Memory User???s Guide
Equipment Approval Information
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.
1Noti???cation to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Notes
???This equipment may not be used on coin service provided by the telephone company.
???Party lines are subject to state tari???s, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company.
???Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
???If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a quali???ed installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) a???ord you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to a???ect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
Visit our website at: www.uniden.com
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o??? and on, the user is encouraged to try to correct the interference by one or more of the following measures:
???Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
???receiving??? the interference).
???Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
???Connect the telecommunications equipment into an outlet on a circuit di???erent from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, ???How To Identify and Resolve Radio/TV Interference Problems.???This booklet is available from the U.S. Government Printing O???ce, Washington, D.C. 20402. Please specify stock number
Notice: The changes or modi???cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be
Introduction
CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.
Short Glossary of Terminology Used in this Manual
Hook switch. The part of the phone that pops up to activate the phone line when the handset is lifted from the base.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
Important Installation Information
CAUTION: Disconnect the phone cord from the wall outlet before installing or replacing the batteries.
???Never install telephone wiring during a lightning storm.
???Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.
???Use caution when installing or modifying telephone lines.
???Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
???Temporarily disconnect any equipment connected to the phone, such as faxes, other phones, or modems.
Base Layout
Installing and Replacing the Batteries
Your Caller ID phone uses 4
IMPORTANT: You will have approximately 90 seconds to replace the batteries before the memories stored are lost. Please read the
instructions before replacing the batteries and have the batteries ready to be inserted beforehand.
IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they may leak and damage the unit.
1. Disconnect the telephone line cord and remove the desk 
stand from the back of the base.
2. Release latch or the battery compartments and remove cover.
3. Insert 4
4. Snap the battery compartment door back into place and
replace the desk stand. 
5. Connect the line cord and check your memory locations.
NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation.
Installing the Phone
Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on a wall.
Connecting the Handset
1.Connect one end of the coiled handset cord to the jack on the handset.
2.Plug the other end of the coiled handset cord to the jack on the base.
3.Place the handset in the cradle.
Connecting the Telephone Line
1.Connect one end of the straight telephone line cord to the jack on the back of the base.
2.Connect the other end to a wall phone jack.
3.Set the ringer volume switch located at the back of the base to
the desired loudness.
- Telephone will not ring. 1 - Sound will be lowest. 2 - Sound will be loudest.
NOTE: The unit is properly installed if you pick up the handset and hear the dial tone. Otherwise, recheck all installation steps.
Wall Mounting
Your speakerphone can also be mounted on a wall plate (not included).
NOTE: To prevent the handset from falling out of the cradle while the phone is hanging on the wall, you must switch both the handset hook and the desk stand to their
??? On the front of the base, pull the handset hook out of the slot. Rotate hook 180 degrees and ???ip it from front to back. Slide it back into the slot. 
??? Turn the base over. Press in on the tabs and remove the desk stand from the back of the base.
??? Rotate the stand 180 degrees, and insert the hooks marked WALL into the notches marked WALL. Press in on the tabs and snap the stand into place.
??? Connect the telephone line cord to the wall jack and the phone. If desired, wrap any excess cord around the cord hooks as shown.
??? Place the mounting slots over the pins on the wall plate, and slide the base down to lock it into place.
Telephone Basics
You can use the telephone by speaking into and listening through the handset, or by using the speakerphone.
Receiving a Phone Call
Making a Phone Call
1.Lift the handset or press the speaker button. Wait for a dial tone.
2.Dial the telephone number you want to call.
3.Replace the handset in the cradle, or press the speaker button to hang up.
Volume
You may adjust the handset and speakerphone volume independently with the VOL ( - or + ) buttons. Both handset receiver volume level and speakerphone volume level are saved in memory.
Adjusting the Handset Receiver Volume
While using the handset, you can adjust the speaker volume by pressing the VOL ( - or + ) buttons. The screen displays volume.
Adjusting the Speakerphone Volume
While using the speakerphone, you can adjust the speaker volume by pressing the VOL ( - or + ) buttons. The screen displays volume level.
NOTE: Both handset receiver and speakerphone volume return to the default setting (low) if the unit's power is reset.
Redial
You may redial the last number you called by pressing the redial button after you hear a dial tone.
NOTE: The redial feature holds the last number (up to 32 digits) that you dialed in memory. If you pressed any other numbers after dialing the phone number (for example, when accessing a
Mute
Use the mute button to interrupt a phone conversation to talk privately with someone else in the room. A conversation can be muted while using the speakerphone or handset.
1.Press the mute button. The mute indicator illuminates.
2.Press mute again to turn it o???.
NOTE: Switching from speakerphone to handset cancels mute.
Flash
Press ???ash/exit to activate special features of your telephone network, such as call transfer, or special services from your local telephone company, such as call waiting.
Temporary Tone Dialing
If you have pulse (rotary) service and want to access customer calling services (such as telebanking and long distance services) that require tone dialing, you can use this feature to temporarily change from pulse to tone service.
After dialing the telephone number and connecting to the customer calling service,
1.Press and release the *tone button.
2.When you hang up, the telephone automatically returns to pulse dialing mode.
Speakerphone Basics
Location
Your phone features a speakerphone for ease of use and convenience during a phone conversation. At any time during a conversation, you can lift the handset to stop using the speakerphone. Likewise, when you are using the handset, press the speaker button and place the handset in the cradle to switch to the speakerphone.
For best speakerphone performance, avoid the following:
???Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you ???nish talking.)
???Surfaces a???ected by vibration.
???Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo e???ect.
Speakerphone Use
Note the following guidelines when using the speakerphone:
???The speakerphone works similar to a
???Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking.
???You can adjust the speaker volume by pressing the VOL ( - or + ) buttons.
???The speakerphone indicator light comes on when the speakerphone is in use.
NOTE: Batteries must be installed for the speakerphone to operate.
Caller ID (CID) Features
IMPORTANT: In order to use all of the features of this telephone, you must subscribe to two separate services available from your local telephone company: the standard Name/Number Caller ID Service to know who is calling when the phone rings and Caller ID with Call Waiting Service to know who is calling while you are on the phone.
CID Summary Screen
The Summary Screen shows the current time, date, and number of new calls to review. It is displayed until any button is pressed.
NOTE: The number of new calls is displayed until all new calls have been reviewed.
Receiving and Storing CID Calls
This units receives and displays information transmitted by your local company. This information can include the phone number,date, and time ;or the name , phone number, date, and time. The unit can store up to 75 calls for later review. When the memory is full, a new call automatically replaces the oldest call in memory. The screen displays NEW for calls received that have not been reviewed. The screen displays REPT for calls received more than once which have not been reviewed.
Reviewing CID Records
???Press the review ??? or ???buttons to view the call records.
???Press the review ??? button to scroll through the call records from the most recent to the oldest.
???Press the review ??? button to scroll through the call records from the oldest to the newest.
???When all of the records have been viewed, The screen displays START/END.
Deleting CID Records
???To delete the record shown in the display, press the delete button once.
???To delete all records while reviewing, press and hold the delete button for about three seconds. The screen displays DELETE ALL?. Press delete again to complete.
Dialing Back
When reviewing Caller ID records, you can dialback the numbers on the display by pressing the dial button.
NOTE: If the screen displays PICKUP PHONE, no other changes to the number can be made. The information sent from the telephone company is known to be a valid number for dialing back (used only in very limited areas). Once you pickup the phone, the number is automatically dialed.
If You Programmed Your Local Area Code
1.Use the review ??? or ??? buttons to display the number you want to dial.
2.Press the dial button.
???If you see a number with seven digits (i.e.
???If you see a number with 11 digits (i.e.
NOTE: A timer (10 seconds
3.If you are at
4.To dial the displayed number, and the phone is
If You Did Not Program Your Local Area Code
1.Use the review ??? or ??? buttons to display the number you want to dial. You will only see
2.See steps 2 through 4 in the previous section to complete the dialback process.
Setting Up the Caller ID Menu
You should not plug the telephone into the modular jack while setting up the Caller ID menu.
1.Press the menu button to enter the menu feature con???guration mode.
#1. >ENG FRA ESP (CID language default English)
#2. CONTRAST (default level is 3)
#3. LOCAL AREA CODE
#4. TONE PULSE (Default is tone dialing).
2.Press the menu button to scroll through the 4 menu screens.
3.Use the ??? or ??? buttons to select the desired setting.
NOTE: You have 20 seconds following an entry before the phone returns to the Summary Screen.
Display Language
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.
1.Press the menu button until the screen displays ENG FRA ESP.
2.Use the review ??? or ??? buttons to select ENG, FRA or ESP.
3.Press the menu button again to save.
Contrast
This adjustment allows you to adjust the contrast of the display.
1.Press the menu button until the screen displays CONTRAST.
2.Use the review ??? or ??? buttons to select level 1, 2, 3, 4, or 5.
3.Press the menu button again to save.
Local Area Code
The telephone uses the programmed area codes to determine the number format to display when a valid Caller ID signal is received. Numbers that match the local area code are displayed as seven digits and are used for dialing back previous numbers. Entering your local area code will also help you immediately know if the call is local or long distance when viewing the CID records in the display.
NOTE: If you make a mistake and want to start over again, press the delete button to erase all of the digits.
1.Press the menu button until the screen displays LOCAL AREA CODE.
2.Use the number keys to enter the Local Area Code you want.
3.Press the menu button to save.
Dialing Mode
This adjustment allows you to select tone
Memory
You may store information in any of the following memory locations: 0 to 9, A, B, and C . See ???Storing a Pause in Memory??? and ???Temporary Tone Dialing??? for more information.
Storing a Name and Number in Memory
1.Press the store button. The screen displays LOCATION?.
2.Press the desired memory location
NOTE: You may select memory locations by pressing review ??? or ??? buttons to scroll through the memory locations or press the 0 - 9, A, B, C.
3.Press the store button again to con???rm the memory location.
NOTE: If necessary, to erase existing memories, or if you make a mistake, use the delete button.
4.Use the number keys to enter the telephone number (up to 32 digits) and press the store button to save. (The unit will not dial a phone number in this mode.) The cursor automatically moves to the text line for name entry.
5.Use the number keys to enter the name of the person associated with the telephone number you just entered. More than one letter is stored in each of the number keys.
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.
NOTE: The ???ashing cursor automatically moves to the next position or you may press the review??? or ??? buttons to move the cursor to the next position.
Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for the letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 4 key twice for the letter H.
6.Press the store button to save the name.
7.To enter another name and number in a di???erent memory location, return to step 1 and repeat the process.
Changing a Stored Number
Repeat the storage sequence under ???Storing A Name and Number in Memory???, and use the delete button to delete the old number before entering the new number.
Erasing a Stored Number
1.Press the store button.
2.Press the memory location
3.Press the delete button.
Copying Caller ID Memories to User Memory
1.Press the review ??? or ??? buttons to view the caller number and name you want to copy.
2.Press the store button.
3.Press the memory location
4.Press the store button to enter the edit mode, and then press the store button again to edit the name.
NOTE: You may select a di???erent memory location by pressing review ??? or ??? buttons to scroll through the memories or press a number key
5.Press the store button to con???rm and save, and wait for three seconds to exit.
NOTE: If the name you want to enter is longer than 12 characters, only the ???rst 12 characters will be copied into memory.
Storing a Redial Number to Memory
1.Press the store button.
2.Press any key
3.Press the store button again to con???rm.
4.Press the redial button, and then press the store button again.
5.Enter name, if necessary, and then press the store button to con???rm.
NOTE: If you want to edit the number, press the store button again within three seconds. When you are ???nished, wait three seconds to exit.
Dialing a Number Stored in Memory While
1.Press the dial button.
2.To select a memory, press any number key
NOTE: You may select a di???erent memory location by pressing review
???or ??? buttons to scroll through the memories or press a number key
3.Press the speaker button, or pick up the handset to dial the displayed number.
Dialing a Number Stored in Memory
1.Lift the handset, or press the speaker button.
2.Press the dial button then press a memory location button.
Cascade Dialing
This process allows you to dial a succession of stored numbers from separate memory locations. This is useful when you must dial several sequences of numbers, such as with frequent calls via a telephone company long distance provider.
1.Pick up the handset or press speaker.
2.Press dial button, then press number ???6??? for the memory location.
3.Press dial button, then press number ???7??? for the memory location.
4.Press dial button, then press number ???8??? for the memory location.
5.The number dials automatically.
Storing a Pause in Memory
The redial button has dual functionality and becomes a pause button when the store button is pressed ???rst. It is valid only when storing a number into memory locations. Use the redial/pause button to insert a pause when a delay is needed in an automatic dialing sequence. For example, when you must dial a 9 to get an outside line or when you enter codes to access your long distance company.
telephone number shows in the display.
2.Lift the handset or press the speaker button and the number automatically dials.
NOTE: Use the delete button to delete an incorrectly entered number.
Caller ID Display Messages
The following special messages indicate the status of a message or the unit:
BLOCKED CALL The caller of the incoming call is registered as
???Private Number??? and their Caller ID information is withheld.
PRIVATE CALLER The incoming call does not have Caller ID service or their service area is not linked to yours. If the screen displays PRIVATE CALLER along with a calling number, the name information for that number was not available.
Troubleshooting Tips
No Dial Tone
???Check all cabling to make sure that all connections are secure and not damaged.
???Check hook switch: Does it fully extend when handset is lifted from cradle?
No Display
???Replace the batteries.
???Check for proper battery installation.
No Information is Shown After the Phone Rings
???Are you subscribed to Caller ID service from your local telephone company?
???Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
???Make sure TONE PULSE is set to TONE DIAL. Phone Won???t Dial Out with Pulse Service
???Make sure TONE PULSE is set to PULSE DIAL. Phone Does Not Ring
???Make sure ringer switch is set to 1 or 2.
???You may have too many extension phones on your line. Try unplugging some extension phones.
???Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
???Are other phones o??? hook at same time? If so, this is normal condition as volume drops when additional phones are used at once.
???Check the handset receiver or speaker volume.
Memory Dialing
??? Make sure you entered the numbers correctly into memory.
General Product Care
To keep your phone working and looking good, follow these guidelines:
???Avoid putting it near heating appliances and devices that generate electrical noise
(for example, motors or ???uorescent lamps).
???DO NOT expose to direct sunlight or moisture.
???Avoid dropping and other rough treatment to the unit.
???Clean with a soft cloth.
???Never use a strong cleaning agent or abrasive powder because this will damage the
???nish.
???Retain the original packaging in case you need to ship it at a later date.
Service
If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at
This product may be serviced only by the manufacturer or its authorized service agents. Changes or modi???cations not expressly approved by Uniden America Corporation could void the user???s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this guide or call customer service at
Or refer inquiries to:
Uniden America Service
4700 Amon Carter Blvd.
Forth Worth, TX 76155
Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable if service should be required during the warranty period.
Purchase Date
Name of Store
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Speci???cations. This is con???rmed by the registration number. The abbreviation, IC, before the registration number signi???es that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical speci???cations were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides
an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed ???ve.
IMPORTANT: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (???Uniden???) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further e???ect 12 months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modi???ed, altered, or used as part of any conversion kits, subassemblies, or any con???gurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner???s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in e???ect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or
its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO
THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY
NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE
FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you speci???c legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF
WARRANTY: If, after following the instructions in the owner???s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Uniden?? is a registered trademark of Uniden America Corporation.
The pictures in this manual are used for examples only. Your actual phone may not look exactly like the pictures.
1. With the handset on the cradle, enter the telephone number you wish to call. The