User's Manual
TECRA
Satellite
A series
User's Manual
TECRA
Satellite
A series
Table of Contents
Chapter 1
TOSHIBA Legal, Regulatory and
Safety
This chapter states the Legal, regulatory and safety information applicable to TOSHIBA computers.
Copyright, Disclaimer and Trademarks
Copyright
?? 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
First edition September 2013
Copyright authority for music, movies, computer programs, databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author's rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.
Disclaimer
This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for your computer at the time of this manual???s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.
Trademarks
Intel, Intel SpeedStep, Intel Core and Centrino are trademarks or registered trademarks of Intel Corporation.
Windows, Microsoft and Windows logo are registered trademarks of Microsoft Corporation.
The Bluetooth?? word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license.
The terms HDMI and HDMI
DisplayPort and the DisplayPort logo are trademarks of Video Electronics Standards Association.
DTS, the Symbol, & DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS, Inc. ?? DTS, Inc. All Rights Reserved.
Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association.
QUALCOMM is a trademark of Qualcomm Incorporated, registered in the United States and other countries. ATHEROS is a trademark of Qualcomm Atheros, Inc., registered in the United States and other countries.
Realtek is a registered trademark of Realtek Semiconductor Corporation.
All other product names and service names in this manual may be trademarks or registered trademarks of their respective companies.
Regulatory Information
The regulatory information herein may vary. Pease check the ID information on the back of the device for specific information applicable to the model you purchased.
FCC information
FCC notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that may cause undesired operation.
Contact
Address: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California
Telephone: (949)
This information is only applicable for the countries/regions where it is required.
EU Declaration of Conformity
This product is carrying the
CE compliance
This product is labelled with the CE Mark in accordance with the related European Directives, notably RoHS Directive 2011/65/EU and Electromagnetic Compatibility Directive 2004/108/EC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/ EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006/95/EC for the supplied power adapter. Furthermore the product complies with the Ecodesign Directive 2009/125/EC (ErP) and its related implementing measures.
This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted:
Only CE marked options should be connected/implemented Only best shielded cables should be connected
Working environment
This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for
For example, the following environments are not approved:
Industrial Environments (e.g. environments where a mains voltage of 380 V
Medical Environments
Automotive Environments
Aircraft Environments
Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA.
The consequences of the use of this product in
Interference with other devices or machines in the near surrounding area.
Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the near surrounding area.
Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all
the manufacturer or airline respectively should be asked for permission before use of this product.
Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.
VCCI Class B Information (Japan Only)
????????????????????????????????????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????????????????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????????????????????????
??????????????????
Canadian regulatory information (Canada only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.
Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian
Cet appareil num??rique de la class B respecte toutes les exgences du R??glement sur le mat??riel brouileur du Canada.
Following information is only valid for
Disposal of products
The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres.
The black bar indicates that the product was placed on the market after August 13, 2005.
By participating in separate collection of products and batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling programmes available in your country, please visit our website
Disposal of batteries and/or accumulators
The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.
If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/ EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling programmes available in your country, please visit our website
These symbols may not stick depending on the country and region where you purchased.
REACH - Compliance Statement
The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.
Please consult the following website
No 1907/2006 (???REACH???) in a concentration above 0.1 % weight by weight.
Following information is only for Turkey:
Compliant with EEE Regulations: TOSHIBA meets all requirements of Turkish regulation 26891 ???Restriction of the use of certain hazardous substances in electrical and electronic equipment???.
The number of possible pixel failures of your display is defined according to ISO
Following information is only for India:
The use of this symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please visit our website (http://www.toshiba- india.com) or contact call center
These symbols may not stick depending on the country and region where you purchased.
Video Standard Notice
THIS PRODUCT IS LICENSED UNDER THE AVC, THE
AND
VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO")
AND/OR (II) DECODING AVC,
ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
OpenSSL Toolkit License Issues
LICENSE ISSUES
==============
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are
OpenSSL License
/*===================================================== Copyright (c)
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.All advertising materials mentioning features or use of this software must display the following acknowledgment:
"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4.The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact
5.Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.
6.Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS''
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
=====================================================
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).
*/
Original SSLeay License
/* Copyright (C)
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and
Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed.
If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.
This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.All advertising materials mentioning features or use of this software must display the following acknowledgement:
"This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)"
The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic
4.If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:
"This product includes software written by Tim Hudson (tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]
*/
FreeType License Issues
The FreeType Project LICENSE
Copyright
David Turner, Robert Wilhelm, and Werner Lemberg Introduction
============
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software in commercial and freeware products alike. As a consequence, its main points are that:
We don't promise that this software works. However, we will be interested in any kind of bug reports. (`as is' distribution)
You can use this software for whatever you want, in parts or full form, without having to pay us.
You may not pretend that you wrote this software. If you use it, or only parts of it, in a program, you must acknowledge somewhere in your documentation that you have used the FreeType code. (`credits')
We specifically permit and encourage the inclusion of this software, with or without modifications, in commercial products.
We disclaim all warranties covering The FreeType Project and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text:
"""
Portions of this software are copyright (C) <year> The FreeType Project (www.freetype.org). All rights reserved.
"""
Please replace <year> with the value from the FreeType version you actually use.
Legal Terms
============
0. Definitions
Throughout this license, the terms `package', `FreeType Project', and `FreeType archive' refer to the set of files originally distributed by the
authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project', be they named as alpha, beta or final release.
`You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executable'. This program is referred to as `a program using the FreeType engine'.
This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise stated in the file in its original, unmodified form as distributed in the original archive. If you are unsure whether or not a particular file is covered by this license, you must contact us to verify this.
The FreeType Project is copyright (C)
1. No Warranty
THE FREETYPE PROJECT IS PROVIDED `AS IS' WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN
NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE
INABILITY TO USE, OF THE FREETYPE PROJECT. 2. Redistribution
This license grants a worldwide,
Redistribution of source code must retain this license file (`FTL.TXT') unaltered; any additions, deletions or changes to the original files must be clearly indicated in accompanying documentation. The copyright notices of the unaltered, original files must be preserved in all copies of source files.
Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team, in the distribution documentation. We also encourage you to put an URL to the FreeType web page in your documentation, though this isn't mandatory.
These conditions apply to any software derived from or based on the FreeType Project, not just the unmodified files. If you use our work, you must acknowledge us. However, no fee need be paid to us.
3. Advertising
Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission.
We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project', `FreeType Engine', `FreeType library', or `FreeType Distribution'.
As you have not signed this license, you are not required to accept it. However, as the FreeType Project is copyrighted material, only this license, or another one contracted with the authors, grants you the right to use, distribute, and modify it. Therefore, by using, distributing, or modifying the FreeType Project, you indicate that you understand and accept all the terms of this license.
4. Contacts
There are two mailing lists related to FreeType: 
freetype@nongnu.org
Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution. If you are looking for support, start in this list if you haven't found anything to help you in the documentation.
Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc.
Our home page can be found at http://www.freetype.org
ENERGY STAR?? Program
Your Computer model may be ENERGY STAR?? compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies.
TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes.
To conserve energy, your computer is set to enter the low- power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode.
TOSHIBA recommends that you leave this and other energy saving features active, so that your computer will operate at its maximum energy efficiency. You can wake the computer from Sleep Mode by pressing the power button.
Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the US EPA and the EU Commission. According to the EPA, a computer meeting the new ENERGY STAR specifications will use between 20% and 50% less energy depending on how it is used. Visit
Disposing of the computer and the computer's batteries
Contact an authorized TOSHIBA service provider for details regarding how to dispose of the computer and the batteries.
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Provide adequate ventilation
Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode). In this condition, observe the following:
Never cover your computer or AC adaptor with any object.
Never place your computer or AC adaptor near a heat source, such as an electric blanket or heater.
Never cover or block the air vents including those located at the base of the computer.
Always operate your computer on a hard flat surface. Using your computer on a carpet or other soft material can block the vents.
Always provide sufficient space around the computer.
Overheating your computer or AC adaptor could cause system failure, computer or AC adaptor damage or a fire, possibly resulting in serious injury.
Creating a
Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.
Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.
To keep your computer in prime operating condition, protect your work area from:
Dust, moisture, and direct sunlight.
Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.
Extreme heat, cold, or humidity. Liquids and corrosive chemicals.
Stress injury
Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress.
Heat injury
Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a
If the computer has been used for a long time, avoid direct contact with the metal plate supporting the various interface ports as this can become hot.
The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction. If you need to transport the AC adaptor, you should disconnect it and let it cool before moving it. Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction.
Cleaning the computer
To help ensure long,
Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.
Clean the plastics of the computer using a slightly water dampened cloth.
You can clean the display screen by spraying a small amount of glass cleaner onto a soft, clean cloth and then wiping the screen gently with the cloth.
Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.
Moving the computer
While the computer is designed for flexible
Make sure all disk/disc activity has ended before moving the computer.
Turn off (shut down) the computer.
Disconnect the AC adaptor and all peripherals before moving the computer.
Close the display panel.
Do not pick up the computer by its display panel.
Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.
Be careful not to subject the computer to impact or shock - a failure to follow this instruction could result in damage to computer, computer failure or loss of data.
Never transport your computer with any cards installed - this may cause damage to either the computer and/or the card resulting in computer failure.
Always use a suitable carry case when transporting the computer. When carrying your computer, be sure to hold it securely so that it does not fall or hit anything.
Do not carry your computer by holding any of its protruding elements.
Mobile phones
Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.
Instruction Manual for Safety and Comfort
All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer.
Safety Icons
Safety icons are used in this manual to bring important information to your attention. Each type of message is identified as shown below.
Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
A caution informs you that improper use of equipment or failure to follow instructions may cause data loss, equipment damage, or may result in minor or moderate injury.
Please read. A note is a hint or advice that helps you make best use of your equipment.
Chapter 2
Getting Started
This chapter provides an equipment checklist, and basic information to start using your computer.
Some of the features described in this manual may not function properly if you use an operating system that was not
Equipment checklist
Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Hardware
Check to make sure you have all the following items:
TOSHIBA Portable Personal Computer
AC adaptor and power cord
Spare AccuPoint (pointing device) cap (Is included with some models) Cleaning cloth (provided with some models)
Documentation
User Information Guide
Instruction Manual for Safety and Comfort
If any of the items are missing or damaged, contact your dealer immediately.
Conventions
This manual uses the following formats to describe, identify, and highlight terms and operating procedures.
Start
Click
The word "Start" refers to the " 
" button in Windows 7.
Tap the Touch Pad or click the left Touch Pad control button once.
Left click the mouse once.
Tap the touch screen once (only for touch screen models).
Short Name
Short Name is defined as shown below in this manual.
Using your computer for the first time
Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.
This section provides basic information to start using your computer. It covers the following topics:
Connecting the AC adaptor
Opening the display
Turning on the power Initial setup
Use a
Never format storage media without checking its content - formatting erases all stored data.
It is a good idea to periodically back up the internal HDD/SSD or other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.
Before you install a device or application, save any data in memory to the HDD/SSD or other storage media. Failure to do so may result in the loss of data.
Connecting the AC adaptor
Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.
The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.
Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.
Never plug the AC adaptor into a power source that does not correspond to both the voltage range and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.
Always use or purchase power cables that comply with the legal voltage, frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.
The supplied power cord conforms to safety rules and regulations in the region the computer is bought and may not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.
Do not use a
When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in this User???s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Never place your computer or AC adaptor on a wooden surface, furniture, or any other surface that could be marred by exposure to heat since the computer base and AC adaptor's surface increase in temperature during normal use.
Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage.
Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.
1.Connect the power cord to the AC adaptor.
Figure
Either a
2.Connect the AC adaptor???s DC output plug to the DC IN 19V jack on your computer.
3.Plug the power cord into a live wall outlet - the DC IN/Battery indicator should glow.
Figure
1 2 
Figure
1 
2
Figure
Product appearance depends on the model you purchased.
Opening the display
The display panel can be opened to a wide range of angles for optimal viewing.
While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.
Figure
1
1. Display panel
Product appearance depends on the model you purchased.
Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Be careful not to open the display panel too far as this could put stress on the display panel???s hinges and cause damage.
Do not press or push on the display panel. Do not lift the computer by the display panel.
Do not close the display panel with pens or any other objects left in between the display panel and the keyboard.
When opening or closing the display panel, place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel).
Turning on the power
This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Power Condition Descriptions section for more information.
After you turn on the power for the first time, do not turn it off until you have set up the operating system.
Volume cannot be adjusted during Windows Setup.
1.Open the display panel.
2.Press the computer's power button.
Figure
1
Figure
1
Figure
1
1. Power button
Product appearance depends on the model you purchased.
Initial setup
The Windows Startup Screen will be the first screen displayed when you turn on the power. Follow the
When it is displayed, be sure to read the License Terms carefully.
Turning off the power
The power can be turned off in one of the following modes, either Shut Down Mode, Sleep Mode or Hibernation Mode.
Shut Down Mode
When you turn off the power in Shut Down Mode, no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.
1.If you have entered data, either save it to the HDD/SSD or to other storage media.
2.Make sure all disk/disc activity has stopped before removing the disk/ disc.
If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk.
Never turn off the power while an application is running. Doing so could cause loss of data.
Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss.
3.Click Start.
4.Select Shut down from the Shut down options.
5.Turn off any peripheral devices connected to your computer.
Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage.
Restarting the computer
Certain conditions require that you reset the computer, for example if:
You change certain computer settings.
If you need to restart the computer, there are two ways this can be achieved:
Click Start. Point to the arrow (
) beside the Shut down button and then select Restart from the menu.
Press CTRL, ALT and DEL simultaneously (once) to display the menu window, and then select Restart by clicking the power icon (
) in the
Before restarting the computer, be sure to save your data.
Sleep Mode
If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer's main memory. When you turn on the power again, you can continue working right where you left off.
When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication functionalities, and cancelling settings that reactivate the computer automatically, such as a timer recording function. Failure to
completely shut down the computer in this way could allow the operating system to reactivate and run
Before entering Sleep Mode, be sure to save your data.
Do not switch to Sleep Mode while transferring data to external media, such as USB devices, memory media or other external memory devices, as data will be lost.
When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in the Power Options (to access it, click Start
To restore the operation of the computer from Sleep Mode, press and hold the power button or any key on the keyboard for a short amount of time. Please note that keyboard keys can only be used if the Wake- up on Keyboard option is enabled within the TOSHIBA HWSetup utility.
If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.
To prevent the computer from automatically entering Sleep Mode, disable Sleep Mode within the Power Options.
To use the Hybrid Sleep function, configure it in the Power Options.
Benefits of Sleep Mode
The Sleep Mode feature provides the following benefits:
Restores the previous working environment more rapidly than the Hibernation Mode feature.
Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature.
Allows the use of the panel power off feature.
Executing Sleep Mode
You can enter Sleep Mode in one of three ways:
Click Start. Point to the arrow (
) beside the Shut down button and then select Sleep from the menu.
Close the display panel. Please note that this feature must be enabled within the Power Options.
Press the power button. Please note that this feature must be enabled within the Power Options.
When you turn the power back on, you can continue where you left off when you shut down the computer.
When the computer is in Sleep Mode, the Power indicator will blink amber.
If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off.
Sleep Mode limitations
Sleep Mode will not function under the following conditions:
Power is turned back on immediately after shutting down.
Memory circuits are exposed to static electricity or electrical noise. The battery power is exhausted and the AC Adaptor is not connected.
Hibernation Mode
The Hibernation Mode feature saves the contents of memory to the HDD/ SSD when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer.
Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the HDD/SSD. However, for safety sake, it is best to save your data manually.
Data will be lost if you disconnect the AC adaptor before the save is completed.
Do not switch to Hibernation Mode while transferring data to external media, such as USB devices, memory media or other external memory devices, as data will be lost.
Benefits of Hibernation Mode
The Hibernation Mode feature provides the following benefits:
Saves data to the HDD/SSD when the computer automatically shuts down because of a low battery condition.
You can return to your previous working environment immediately when you turn on the computer.
Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.
Allows the use of the panel power off feature.
Starting Hibernation Mode
To enter Hibernation Mode, follow the steps below.
1.Click Start. Point to the arrow (
) beside the Shut down button and then select Hibernate from the menu.
Automatic Hibernation Mode
The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below:
1.Click Start
2.Click Choose what the power button does or Choose what closing the lid does.
3.Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid.
4.Click the Save changes button.
Data save in Hibernation Mode
When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the HDD/SSD.
After you turn off the computer, and the content of memory has been saved to the HDD/SSD, turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Chapter 3
The Grand Tour
This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer.
Legal Footnote
For more information regarding
Legal Footnotes section.
Please handle your computer carefully to avoid scratching or damaging the surface.
Short Name is defined as shown below in this manual.
The Grand Tour for
Front with the display closed
The following figure shows the front of the computer with the display panel in the closed position.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.
Wireless communication indicator
The Wireless communication indicator glows white when the Wireless functions are turned on.
Some models are equipped with Wireless functions.
Wireless WAN/WiMAX The Wireless WAN/WiMAX indicator glows indicatorblue when the Wireless WAN/WiMAX functions
are turned on.
In some models, the indicator will glow and blink in order to indicate the connection status of the Wireless WAN/WiMAX function.
Some models are equipped with a Wireless WAN/WiMAX function.
Left side
The following figures show the left side of the computer.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
USB 3.0 port(s) may work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.
Keep foreign metal objects, such as screws, staples and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Right side
The following figures show the right side of the computer.
Figure
Product appearance depends on the model you purchased.
Memory media slot This slot lets you insert an SD???/SDHC???/ SDXC??? memory card, miniSD???/microSD??? Card and MultiMediaCard???. Refer to the Memory media section for more information.
Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Universal Serial Bus Two Universal Serial Bus ports, which comply to
Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction.
Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer.
Back
The following figure shows the back of the computer.
Figure
1
1. Cooling vents
Product appearance depends on the model you purchased.
Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Carefully clean the dust on the cooling vents??? surface using a soft cloth.
Underside
The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
Figure
1. Cooling vents2. Docking port*
* Provided with some models.
Product appearance depends on the model you purchased.
Only the TOSHIBA
Do not attempt to use any other Port Replicator.
Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
Front with the display open
This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.
Figure
3 4 2
9 
detection area*
10.AccuPoint*
* Provided with some models.
Product appearance depends on the model you purchased.
Wireless LAN
Wireless LAN/Bluetooth
Legal Footnote (Wireless LAN)
For more information regarding Wireless LAN, please refer to the Legal Footnotes section.
Do not point the web camera directly at the sun.
Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.
Please be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries.
Legal Footnote (LCD)
For more information regarding LCD, please refer to the Legal Footnotes section.
The Grand Tour for
Front with the display closed
The following figure shows the front of the computer with the display panel in the closed position.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.
Wireless WAN/WiMAX The Wireless WAN/WiMAX indicator glows
Left side
The following figures show the left side of the computer.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
USB 3.0 port(s) may work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.
Keep foreign metal objects, such as screws, staples and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Right side
The following figures show the right side of the computer.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
Universal Serial Bus Two Universal Serial Bus ports, which comply to
Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction.
Back
The following figure shows the back of the computer.
Figure
Product appearance depends on the model you purchased.
Underside
The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
Figure
1. Cooling vents2. Docking port*
* Provided with some models.
Product appearance depends on the model you purchased.
Only the TOSHIBA
Do not attempt to use any other Port Replicator.
Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
Front with the display open
This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.
Figure
6
11
5
10
6
8
11
detection area*
10.AccuPoint
* Provided with some models.
Product appearance depends on the model you purchased.
Legal Footnote (Wireless LAN)
For more information regarding Wireless LAN, please refer to the Legal Footnotes section.
Do not point the web camera directly at the sun.
Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.
Please be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries.
Legal Footnote (LCD)
For more information regarding LCD, please refer to the Legal Footnotes section.
The Grand Tour for
Front with the display closed
The following figure shows the front of the computer with the display panel in the closed position.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.
Power indicator The Power indicator normally glows white when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash amber.
HDD/SSD indicator The HDD/SSD indicator blinks white whenever the computer is accessing the
Wireless communication indicator
The Wireless communication indicator glows white when the Wireless functions are turned on.
Some models are equipped with Wireless functions.
Wireless WAN/WiMAX The Wireless WAN/WiMAX indicator glows indicatorblue when the Wireless WAN/WiMAX functions
are turned on.
In some models, the indicator will glow and blink in order to indicate the connection status of the Wireless WAN/WiMAX function.
Some models are equipped with a Wireless WAN/WiMAX function.
Left side
The following figures show the left side of the computer.
Figure
* Provided with some models.
Product appearance depends on the model you purchased.
USB 3.0 port(s) may work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.
Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.
Keep foreign metal objects, such as screws, staples and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Right side
The following figures show the right side of the computer.
Figure
Product appearance depends on the model you purchased.
Memory media slot This slot lets you insert an SD???/SDHC???/ SDXC??? memory card, miniSD???/microSD??? Card and MultiMediaCard???. Refer to the Memory media section for more information.
Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Universal Serial Bus Two Universal Serial Bus ports, which comply to (USB 3.0) port the USB 3.0 standard, are provided on the right
side of the computer.
The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.
Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction.
Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer.
Back
The following figure shows the back of the computer.
Figure
1
1. Cooling vents
Product appearance depends on the model you purchased.
Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Carefully clean the dust on the cooling vents??? surface using a soft cloth.
Underside
The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
Figure
1. Cooling vents2. Docking port*
* Provided with some models.
Product appearance depends on the model you purchased.
Only the TOSHIBA
Do not attempt to use any other Port Replicator.
Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
Front with the display open
This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.
Figure
6
detection area*
10.AccuPoint
* Provided with some models.
Product appearance depends on the model you purchased.
Wireless LAN
Wireless LAN/Bluetooth
Legal Footnote (Wireless LAN)
For more information regarding Wireless LAN, please refer to the Legal Footnotes section.
Do not point the web camera directly at the sun.
Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.
Please be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries.
Legal Footnote (LCD)
For more information regarding LCD, please refer to the Legal Footnotes section.
Internal Hardware Components
This section describes the internal hardware components of your computer.
The actual specifications may vary depending on the model you purchased.
Legal Footnote (Battery Life)
For more information regarding Battery Life, please refer to the Legal Footnotes section.
For more information regarding CPU, please refer to the Legal Footnotes section.
SSD is a
Under certain unusual conditions of prolonged
Legal Footnote (HDD/SSD Capacity)
For more information regarding HDD/SSD Capacity, please refer to the
Legal Footnotes section.
Memory module The memory module is installed in the computer.
Legal Footnote (Memory (Main System))
For more information regarding Memory (Main System), please refer to the
Legal Footnotes section.
Graphics Processing Graphics processing unit (GPU) performance Unitmay vary depending on product model, design
configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode.
Legal Footnote (Graphics Processing Unit (GPU))
For more information regarding Graphics Processing Unit (GPU), please refer to the Legal Footnotes section.
NVIDIA Graphic Control
Some NVIDIA graphics models may include NVIDIA?? Optimus??? technology feature.
NVIDIA?? Optimus??? technology intelligently optimizes notebook performance by seamlessly switching between a discrete NVIDIA GPU for great graphics performance and an Intel integrated graphics chip for sustained battery life. Switching is automatic and does not require the user to reboot the computer.
In the Manage 3D Settings menu of NVIDIA Control Panel, you can change the global 3D settings and create overrides for specific programs. The overrides will be used automatically each time the specified programs are launched.
Please use the default setting for NVIDIA Optimus technology.
If the program does not run normally after the setting has been changed, please restore the program to the default setting.
If the program does not run normally, please restore the Preferred graphics processor to the default setting.
When you use some video playback programs to play video files, the preferred graphics processor in the "Program Settings" tab cannot be changed to the graphics other than "Integrated Graphics".
To access the Program Settings, click "NVIDIA Control Panel"
To launch the NVIDIA Control Panel, Click Start
For more information about the NVIDIA Control Panel system, please refer to the NVIDIA Control Panel Help. To access it, click Help from the main menu and then select NVIDIA Control Panel Help.
On Optimus models, two kinds of Display Drivers are installed: ???Intel?? HD Graphics Driver??? and ???NVIDIA Graphics Driver XXX.XX???.
Do not uninstall the display driver from ???Uninstall Program??? in the Control Panel.
If you have to uninstall the display driver, please follow the steps below:
1.Uninstall ???NVIDIA Graphics Driver XXX.XX???.
2.Then uninstall ???Intel?? HD Graphics Driver???.
Intel?? Display Power Saving Technology
Intel GPU models may include the Display Power Saving Technology feature that can save the computer's power consumption by optimizing picture contrast on the internal LCD.
This feature can be used if the computer is:
running in battery mode
using the internal LCD display only
The Display Power Saving Technology feature is enabled at factory default. If you want to turn this feature off, please change it in the settings accordingly in the Intel?? HD Graphics Control Panel/Intel?? Graphics and Media Control Panel.
You can access this control panel in the following way:
In Intel?? HD Graphics Control Panel:
1.Click Power and select On battery.
2.Click Off under Display Power Saving Technology.
3.Click Apply.
If you want to enable this feature, under the conditions mentioned above, click On under Display Power Saving Technology.
In Intel?? Graphics and Media Control Panel:
1.Click Power.
2.Select On battery from the
3.Clear the Display Power Saving Technology check box.
4.Click OK.
If you want to enable this feature, under the conditions mentioned above, select the Display Power Saving Technology check box.
Intel Rapid Start Technology
Your computer may support Intel?? Rapid Start Technology which enables the computer to change to Hibernation Mode from Sleep Mode after a specified period of time.
With the Intel?? Rapid Start Technology, the Windows can rapidly resume from Hibernation Mode and battery life will be longer than when in Sleep Mode.
Intel?? Rapid Start Technology is enabled at factory default. The computer will switch to Hibernation Mode after two hours of Sleep Mode.
You can use TOSHIBA Setup Utility to enable/disable the function and change the specified time setting from Sleep Mode to Hibernation Mode.
1.Launch the TOSHIBA Setup Utility. Please refer to TOSHIBA Setup Utility section for further information.
2.Select Advanced.
3.Enable/DisableIntel(R) Rapid Start Technology function.
4.You can select the period of time from Sleep Mode to Hibernation Mode using Rapid Start Entry after. If the Immediately option is selected, the computer will switch to Hibernation Mode immediately after your computer goes into the Sleep Mode.
When Intel?? Rapid Start Technology is enabled, switching from Sleep Mode to Hibernation Mode consumes power. When you carry your computer aboard on an aircraft or in places where electronic devices are regulated or controlled, always power off your computer.
When Intel?? Rapid Start Technology is enabled,
The Windows cannot be restored normally if the battery is exhausted when the computer is moving from Sleep Mode to Hibernation Mode.
The partition allocation on the Solid State Drive for the Intel?? Rapid Start Technology cannot be deleted even if Intel?? Rapid Start Technology is disabled.
Intel?? Rapid Start Technology can be used only for Windows operating system.
Intel?? Rapid Start Technology cannot be used in models that do not equipped with a Solid State Drive.
The Windows restore time from Hibernation Mode depends on the amount of system memory used in the computer.
Intel?? Smart Connect Technology
Your computer may support Intel?? Smart Connect Technology which automatically updates your applications such as
To use this function, click the icon ( 
) in the taskbar to start the utility wizard. Follow the
For further information on setting up Intel?? Smart Connect Technology, please refer to the utility help.
When Intel?? Smart Connect Technology is enabled, the computer may be turned on automatically. When you carry your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer.
When Intel?? Smart Connect Technology is enabled, the computer will periodically wake up from sleep mode which consumes the battery power. When battery power is less than 15%, Intel?? Smart Connect Technology may not work properly and you need to recharge the battery and restart the computer.
Please make sure that Intel?? Smart Connect Technology is disabled prior to using other wakeup functions.
Please note that the computer case temperature may rise when Intel?? Smart Connect Technology is enabled.
Power Condition Descriptions
Power conditions
The computer's operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is connected and what the charge level is for that battery.
The LED in the table below refers to the DC IN/Battery indicator.
DC IN/Battery indicator
Check the DC IN/Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected. The following indicator conditions should be noted:
If the battery pack becomes too hot while it is being charged, the charge will stop and the DC IN/Battery indicator will go out. When the battery pack's temperature falls to a normal range, charging will resume - this process will occur regardless of whether the computer's power is on or off.
Power indicator
Check the Power indicator to determine the power status of the computer - the following indicator conditions should be noted:
Chapter 4
Operating Basics
This chapter describes the basic operations of your computer, and highlights the precautions that should be taken when using it.
Using the Touch Screen
Some models are equipped with a touch screen.
You can use your finger to manipulate icons, buttons, menu items, the onscreen keyboard, and other items on the touch screen.
For details and more advanced touch screen gestures to interact with Windows operating system, please refer to Help and Support.
Using the Touch Pad
The Touch Pad located in the palm rest may support the following gestures:
Pinch or stretch Place two or more fingers down on the Touch Pad and move them toward each other (pinch) or away from each other (stretch). This will visually zoom in or out.
Some of the Touch Pad operations described in this section are only supported in certain applications.
The Keyboard
The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
There are different types of keys, specifically typewriter keys, function keys, soft keys, Windows special keys and the keypad overlay.
Never remove the key caps on your keyboard. Doing so could cause damage to the parts under the key caps.
Keyboard indicator
The following figure shows the position of the CAPS LOCK indicator which show the following conditions:
When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed.
Figure
1
1. CAPS LOCK indicator
Product appearance depends on the model you purchased.
Function Key
The function keys (F1 ~ F12) are the twelve keys at the top of your keyboard.
Function keys let you enable or disable certain features of the computer. The functions can be performed by pressing the associated function keys.
Mute
Pressing FN + ESC turns the volume on and off.
Lock
Pressing FN + F1 enters ''Lock computer mode''. To restore your desktop, you need to log on again.
Power Plan
Pressing FN + F2 changes the power settings.
Sleep
Pressing FN + F3 switches the system to Sleep Mode.
Hibernate
Pressing FN + F4 switches the system to Hibernation Mode.
Output
Pressing FN + F5 changes the active display device.
To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Brightness Down
Pressing FN + F6 decreases the computer's display panel brightness in individual steps.
Brightness Up
Pressing FN + F7 increases the computer's display panel brightness in individual steps.
Wireless
Pressing FN + F8 turns the Airplane mode on or off.
If no wireless communication device is installed, no dialog box will appear.
Touch Pad
Pressing FN + F9 enables or disables the Touch Pad function.
Cursor Control keys
Pressing FN + F10 to access the computer's integrated key pad. When activated, the keys with grey markings on their bottom edge become cursor control keys. This function is supported with some models
Numeric Keypad
Pressing FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become numeric keypad keys. This function is supported with some models
ScrLock
Pressing FN + F12 to lock the cursor on a specific line. The power on default is off. This function is supported with some models
Zoom (Display resolution)
Pressing FN + Space changes the display resolution.
Reduce
Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.
Enlarge
Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.
Volume down
Pressing FN + 3 decreases the volume in increment.
Volume up
Pressing FN + 4 increases the volume in increment.
Keyboard Backlight
Pressing FN + 
turns the keyboard backlight on or off. This function is supported with some models.
Flash Cards
Flash Cards makes it visual and easy to access and use the function keys. Normally the cards are hidden from view. To activate and use the Flash Cards, follow the steps below:
1.Press and hold the FN key.
Flash Cards will appear on top of the screen by default.
2.Press the function key or click the card associated with the desired function.
The selected card with available options will appear.
3.Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected.
You can also click the desired option.
For more information, please refer to the TOSHIBA Flash Cards Help file.
To access this help, click Start
Sticky key
You can use the TOSHIBA Accessibility utility to make the FN key sticky, that is, you can press it once, release it, and then press a desired function key. To start the TOSHIBA Accessibility utility, click Start
Windows special keys
The keyboard provides two keys that have special functions in Windows, the Windows logo key activates the Start menu while the application key has the same function as the secondary (right) mouse button.
This key activates the Windows Start menu.
This key has the same function as the secondary (right) mouse button.
Using the AccuPoint
To use the AccuPoint, simply push it with your finger tip in the direction you want to move the
Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad.
Some models are equipped with an AccuPoint.
AccuPoint precautions
Certain conditions can affect the
You touch the AccuPoint during
You apply constant, soft pressure during
There is a sudden temperature change. Strong stress is applied to the AccuPoint.
If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation.
Replacing the cap
The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models.
1.To remove the AccuPoint cap, firmly pinch the cap and pull it straight up.
Figure
1
1. AccuPoint cap
Product appearance depends on the model you purchased.
2.Position a new cap on the peg and press it into place.
The peg is square, so be careful to align the cap???s square hole with the peg.
Using the Fingerprint Sensor
This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:
Logon to Windows and access a security enabled homepage through Internet Explorer.
Files and folders can be encrypted/decrypted and third party access to them prevented.
Unlock the
Authentication of the User Password (and, if applicable, the HDD/SSD Password) when booting up the computer
Fingerprint cannot be used in models that do not have a fingerprint module installed.
How to Swipe your Finger
Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:
Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.
The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.
Figure
1
1
1. Sensor
Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail.
Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor.
There is a possibility of authentication failures if the finger is swiped too quickly or too slowly - follow any
Points to note about the Fingerprint Sensor
Please be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate.
Do not scratch or poke the sensor with your nails or any hard or sharp objects.
Do not press the sensor strongly.
Do not touch the sensor with a wet finger or any wet objects - keep the sensor surface dry and free from water vapor.
Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt may scratch it.
Do not paste stickers or write on the sensor.
Do not touch the sensor with a finger or any other object which may have a
Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.
Wash and dry your hands thoroughly.
Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.
Clean the sensor with a
Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate
Soaked or swollen finger, for example as may occur after taking a bath.
Injured finger
Wet finger
Soiled or oily finger
Extremely dry skin condition on finger
Observe the following to improve the fingerprint recognition success rate.
Enroll two or more fingers.
Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers.
Check the condition of your finger - any conditions which have changed since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered.
As the fingerprint for each finger is different and unique you should ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.
Check the position and speed at which you swipe your finger across the sensor - please refer to the preceding drawing.
The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.
The recognition success rate may differ from user to user.
Points to note about Fingerprint Utility
If Windows file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software.
You can back up the fingerprint data or the information registered to Web Site Passwords.
Please use Import/Export in TOSHIBA Fingerprint Utility main menu. Please also refer to the fingerprint utility Help file for more information by clicking ? in TOSHIBA Fingerprint Utility main menu.
Fingerprint utility limitations
TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or
The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.
The recognition success rate may differ from user to user.
Setup Fingerprint Registration
Please use the following procedure when first using fingerprint authentication.
In use, the fingerprint authentication system will use the same username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process.
This sensor has the memory space for at least twenty fingerprint patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage.
1.Click Start
Fingerprint Utility.
2.The Enroll screen is displayed. Enter the current account password into the Windows Password field. If no Windows password has been configured, you will be asked to configure the new logon password. Then click Next.
3.Click the
4.The instructions for enrollment operation screen is displayed. Carefully read them and then click Next.
5.The scanning practice screen is displayed. You are able to practice swiping (three times) your finger to ensure you use the correct method. When you have finished practicing swiping your finger, click
Next.
6.Swipe four times with the same finger. If scanning of fingerprint succeeds, "Enrollment succeeded! Do you want to save this fingerprint?" message box will appear. Click OK.
7.The following message will be displayed: "It???s strongly recommended you enroll one more fingerprint.". Click OK and repeat Step 3, 4, 5 and 6 with another finger.
It is strongly recommended that you register 2 or more fingerprints.
You cannot enroll the same fingerprint more than once, even on a different user account.
Delete the Fingerprint Data
Saved fingerprint data is stored in special
Delete the fingerprint data for the currently logged in user
1.In the TOSHIBA Fingerprint Utility main menu, select Fingerprint Enroll.
2.In the Fingerprint Enroll window, it enables you to delete the fingerprint data for the currently logged in user. Click an enrolled finger you want to delete. "Do you want to delete?" message box will appear on the screen and then click OK. If you want to delete other fingerprints, repeat this step. If only one fingerprint is registered, the message "At least one fingerprint is required." will appear after clicking OK. You are not allowed to delete a unique fingerprint.
3.Click Close.
4."Do you want to quit?" is displayed. Click OK. It will be returned to the
TOSHIBA Fingerprint Utility main menu.
Delete all users fingerprints
1.In the TOSHIBA Fingerprint Utility main menu, click Run as administrator.
2.User Account Control window is displayed. Click Yes.
3.Swipe your enrolled finger.
4.Select Fingerprint Management option.
5.A list of fingerprint information for all users is shown in the screen. Click the enrolled fingerprint data you want to delete, and then click
Delete Selected Items.
6."Do you want to delete the selected fingerprints?" message box will appear on the screen. Click OK.
7.Click Close.
8."Do you want to quit?" is displayed. Click OK. It will be returned to the
TOSHIBA Fingerprint Utility main menu.
Windows Logon via Fingerprint Authentication
In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.
This is useful especially when many users are using the PCs, as user selection can be skipped.
Fingerprint Authentication Procedure
1.Start up the computer.
2.The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows.
If the fingerprint authentication fails, please logon using the Windows logon password.
A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration.
Fingerprint
Overview about Fingerprint
The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.
If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the
You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint
When swiping your finger, please ensure that you do it slowly and at a constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped.
If there are any changes in the environment or settings related to authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD/SSD Password).
Overview about Fingerprint Single
This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD/SSD Password) and logging onto Windows using only one fingerprint authentication when booting up.
It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint
Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD/SSD Password) and the Windows Logon Password.
How to Enable Fingerprint
It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the
1.Logon as Administrator (means a user has administrator privileges).
2.In the TOSHIBA Fingerprint Utility main menu, click Run As Administrator.
3.User Account Control window is displayed. Click Yes.
4.Swipe your finger across the fingerprint sensor.
5.Select Setting in the main menu to open the Setting window. You can:
Select
Select
6.Click Apply.
7."Save successfully" is displayed. Click OK.
8.Click Close.
9."Do you want to quit?" is displayed. Click OK. It will be returned to the
TOSHIBA Fingerprint Utility main menu.
This modified configuration for fingerprint
Battery
This section explains battery types, use, recharging methods and handling.
Battery types
The computer has different types of batteries.
Battery pack
When the AC adaptor is not connected, the computer's main power source is a lithium ion battery, also referred to in this manual as the main battery.
Real Time Clock (RTC) battery
The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off. If the RTC battery becomes completely discharged, the system will lose this information and the real time clock and calendar will stop working.
You can change the Real Time Clock settings in the TOSHIBA Setup Utility. Please refer to Real Time Clock for further information.
The computer's RTC battery is rechargeable and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed. Dispose of the battery as required by local ordinances or regulations.
The RTC battery does not charge while the computer is turned off even if the AC adaptor is attached.
Care and use of the battery pack
This section provides the important safety precautions in order to handle your battery pack properly.
Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.
The battery pack can explode if not replaced, used, handled or disposed of properly. Use only batteries recommended by TOSHIBA as replacements.
Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened.
Charging the batteries
When the power in the battery pack becomes low, the DC IN/Battery indicator will flash amber to indicate that only a few minutes of battery power remain. If you continue to use the computer while the DC IN/Battery
indicator flashes, the computer will enable Hibernation Mode so that you do not lose any data, and automatically turn itself off.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack, connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet - the DC IN/Battery indicator will glow amber while the battery is being charged.
Charging Time
Refer to User Information Guide about Charging time.
Battery charging notice
The battery may not begin charging immediately under the following conditions:
The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5??C to 35??C (41??F to 95??F).
The battery is nearly completely discharged. In this instance you should leave the AC adaptor connected for a few minutes and the battery should begin charging.
The DC IN/Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions:
The battery has not been used for a long time.
The battery has completely discharged and been left in the computer for a long time.
In such cases you should follow the steps as detailed below:
1.Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off.
2.Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power.
3.Charge the battery until the DC IN/Battery indicator glows white.
Repeat these steps two or three times until the battery recovers normal capacity.
Monitoring battery capacity
Remaining battery power can be monitored using the following methods.
Clicking the battery icon on the Taskbar
Via the Battery Status in the Windows Mobility Center window
You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. This is because the computer needs this time to check the battery's remaining capacity and then calculate the remaining operating time, based on this together with the current power consumption.
Please be aware that the actual remaining operating time may differ slightly from the calculated time.
With repeated discharges and recharges, the battery's capacity will gradually decrease. In view of this it will be noted that an often used, older battery will not operate for as long as a new battery even when both are fully charged.
Maximizing battery operating time
A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on:
Processor speed
Screen brightness
HDD/SSD power off period
How often and for how long you use the HDD/SSD and external disk drives, for example, optical disc.
How much charge the battery contained to begin with.
How you use optional devices, such as a USB device, to which the battery supplies power.
Where you store your programs and data.
Whether you close the display panel when you are not using the keyboard - closing the display saves power.
The environmental temperature - operating time decreases at low temperatures.
System Sleep Mode
System Hibernation Mode
Display power off period
Whether you enable Sleep Mode, which can conserve battery power if you are frequently turning the computer off and on.
Whether you enable Sleep and Charge function.
Batteries exhausted time
Refer to User Information Guide about Batteries exhausted time
Extending battery life
To maximize the life of your battery packs:
At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below.
1.Turn off the computer's power.
2.Disconnect the AC adaptor and turn on the computer's power - if it does not turn on then go to Step 4.
3.Operate the computer on battery power for five minutes. If you find that the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged, however, if the DC IN/Battery indicator flashes or there is some other warning to indicate a low battery condition, go to Step 4.
4.Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power. The DC IN/Battery indicator should glow amber to indicate that the battery pack is being charged, however, in the event that DC IN/Battery indicator does not glow this indicates that power is not being supplied - check the connections for the AC adaptor and the power cord.
5.Charge the battery pack until the DC IN/Battery indicator glows white.
Wireless WAN Device
Some computers in this series are equipped with the Wireless WAN device. This device gives you the ability for a
Installing a SIM Card
To install a SIM card, follow the steps as detailed below:
1.Click Start.
2.Select Shut down from the Shut down options.
3.To pop the SIM card tray partially open, insert a slender object (about 10mm, diameter 0.8mm) such as a straightened paper clip into the eject hole. Gently pull to open the SIM card tray.
Never pull the SIM card tray completely out of the slot.
Figure
1
Figure
1
Figure
1
1. Eject hole
Product appearance depends on the model you purchased.
4.Place the SIM card into the SIM card tray with the metal connectors facing up.
5.Insert the SIM card tray into the SIM card slot, and push the center of the tray to close it. Press gently until it locks into place.
Never pull the SIM card tray completely out of the slot.
Figure
Figure
1
3 
2
Figure
Product appearance depends on the model you purchased.
Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
Do not touch the connectors on the SIM card or on the computer. Debris on the connectors may cause access problems.
Removing a SIM Card
To remove the SIM card, follow the steps as detailed below:
1.To pop the SIM card tray partially open, insert a slender object (about 10mm) such as a straightened paper clip into the eject hole. Gently pull to open the SIM card tray.
2.Remove the SIM card from the SIM card tray.
3.Insert the SIM card tray back into the SIM card slot.
GPS Function
Your computer may include a
The performance of GPS will vary depending on the environment. It might be happen that a location cannot be determined.
Your current location may not be shown depending on the status of GPS or the location. If you are obtaining your current location information from the computer, your current location may not be detected due to the information accuracy. Specifically, your current location may not be detected in the following places or situations:
Inside or directly under a building
Inside a bag or box
Among dense trees
When there is an obstacle (person or object) in the front of the antenna
Underground tunnel, underground, or underwater
Buildings streets or residential areas
Near to the high voltage cables
Bad weather such as heavy rain or snow
LAN
The computer may have
This section describes how to connect/disconnect to a LAN.
The
The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on).
LAN cable types
The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer???s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding
If you are using Gigabit Ethernet LAN (1000 megabits per second,
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE- TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second,
Connecting the LAN cable
To connect the LAN cable, follow the steps as detailed below:
Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur.
Do not connect any power supplying device to the LAN cable that is connected to the LAN jack. Otherwise, malfunctions or damage may occur.
1.Turn off the power to all external devices connected to the computer.
2.Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.
Figure
2
1
Product appearance depends on the model you purchased.
3.Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection.
Memory media
The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory
capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.
Keep foreign objects out of the memory media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
Please note that an adaptor is required to use miniSD/microSD Card.
Please note that not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly.
Figure
MultiMediaCard (MMC)
Points to note about the memory media card
SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment.
Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards.
SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is different, so pay careful attention to the logo when purchasing.
The SD memory card logo is ( 
).
The SDHC memory card logo is (
).
The SDXC memory card logo is (
).
The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. The maximum capacity of SDXC memory cards is 128GB.
Memory media format
New media cards are formatted according to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards.
Formatting a memory media card
Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows.
Should you need to format all areas of the memory card, including the protected area, you will need to obtain an appropriate application that applies the copy protection system.
Media care
Observe the following precautions when handling the card.
Do not twist or bend cards.
Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid.
Do not touch the metal part of a card or expose it to liquids or let it get dirty.
After using card, return it to its case.
The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.
Do not leave a card partially inserted in the slot. Press the card until you hear it click into place.
Set the
Memory cards have a limited lifespan, so it is important to backup important data.
Do not write to a card if the battery power is low. Low power could affect writing accuracy.
Do not remove a card while read/write is in progress.
For more details on using memory cards, see manuals accompanying the cards.
About the
Memory media cards have a
SD Card (SD memory card, SDHC memory card and SDXC memory card)
Set the
Inserting memory media
The following instructions apply to all types of supported media devices. To insert memory media, follow the steps as detailed below:
1.Turn the memory media so that the contacts (metal areas) face down.
2.Insert the memory media into the memory media slot on your computer.
3.Press the memory media gently until it clicks into place.
Figure
Product appearance depends on the model you purchased.
Make sure the memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it.
When inserting the memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost.
Removing memory media
The following instructions apply to all types of supported media devices. To remove memory media, follow the steps as detailed below:
1.Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.
2.Select memory media.
3.Press the memory media to partially extend it out of the computer.
4.Grasp the media and remove it.
If you remove the memory media or turn off the power while the computer is accessing the memory media, you may lose data or damage the media.
Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data in the memory media could be lost.
Do not remove only the miniSD/microSD Card while leaving the adaptor in the memory media slot.
Smart Card
A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded. These cards can be used for a wide variety of applications including telephone related and electronic monetary payments.
This section contains information on the proper use of the Smart Card slot, and it is strongly recommended that you read it before operating the computer.
Some models are equipped with a Smart Card slot.
Your computer supports
Inserting a Smart Card
The Smart Card slot is located on the side of the computer. The Windows
To install a Smart Card, follow the steps as detailed below:
1.Insert the Smart Card into the Smart Card slot with the metal connectors facing up.
2.Press the Smart Card gently to ensure a firm connection is made. The computer will identify the Smart Card and display an icon in the Windows Taskbar.
When inserting a Smart Card into the Smart Card slot, make sure to confirm that the card is oriented correctly before inserting.
Insert the Smart Card until it reaches the end of the Smart Card slot. The Smart Card is partially extended beyond the chassis edge. Do not attempt to insert it further.
Always remove the Smart Card from the Smart Card slot before moving the computer.
Remove the Smart Card after use.
Failure to follow these instructions may result in damage to the computer and/or damage to the Smart Card.
3.After inserting the Smart Card, you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.
Removing a Smart Card
To remove a Smart Card, follow the steps as detailed below:
1.Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.
Before removing the Smart Card, confirm that the Smart Card is not working with any program or system.
Be careful not to bend the Smart Card while removing it from the computer.
2.Point to Smart Card and click the left Touch Pad control button.
3.Grasp the Smart Card and remove it.
External Display
Your computer video capabilities can be enhanced with additional displays.
External displays allows you to share your desktop or extend the desktop area.
As the port operation of all external monitors have not been confirmed, some display devices may not function properly.
Connecting an external display
Your computer comes with a
External RGB monitor port
An external analog monitor can be connected to the External RGB monitor port on the computer. To connect an external analog monitor, follow the steps as detailed below:
1.Connect the RGB cable to the External RGB monitor port.
There are no fastening screws for an external monitor cable on the External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used.
2.Turn the external monitor's power on.
Figure
1. External RGB monitor port2. RGB cable
Product appearance depends on the model you purchased.
When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device.
When displaying desktop on an external analog monitor, desktop is sometimes displayed on the center of the monitor with black bars around desktop (with small size).
At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio.
DisplayPort
Some models are equipped with a DisplayPort. This port enables you to connect an external monitor. To connect a DisplayPort monitor, follow the steps as detailed below:
1.Plug one end of the DisplayPort cable into the DisplayPort on your external monitor.
2.Plug the other end of the DisplayPort cable into the DisplayPort on your computer.
3.Turn on the external monitor.
The HDMI out port
Some models are equipped with an HDMI out port. HDMI
without reducing the quality.
To connect an
To connect a device to the HDMI out port, you must purchase a suitable HDMI cable.
1.Plug one end of the HDMI cable into the HDMI in port of the HDMI display device.
2.Plug the other end of the HDMI cable into the HDMI out port on your computer.
3.Turn the HDMI display device's power on.
Figure
Product appearance depends on the model you purchased.
Please do not plug/unplug an HDMI device under the following conditions: 
The system is starting up.
The system is shutting down.
When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI.
When you unplug the HDMI cable and
Settings for display video on HDMI
To view video on the HDMI display device, be sure to configure the following settings otherwise you may find that nothing is displayed.
Be sure to use the function key to select the display device before starting to play video. Do not change the display device while playing video.
Do not change the display device under the following conditions. 
While data is being read or written.
While communication is being carried out.
Selecting HD Format
To select the display mode, follow the steps as detailed below:
1.Click Start
2.Click Appearance and Personalization.
3.Click Display.
4.Click Change display settings.
5.Click Advanced settings.
6.Click List All Modes.
7.Select one of the mode at List All Modes.
Wireless display
Some models support Intel Wireless Display (Intel WiDi), a wireless technology which utilizes
To use Intel WiDi, either one of the following devices is required:
A compatible external display with
An external display with HDMI port and a digital adaptor featuring Intel WiDi.
The adaptor is a device that connects to the external display via HDMI port and can receive
Type "Intel WiDi" from the Start menu and click Intel(R) WiDi. Intel WiDi application will launch and you are ready to start the connection.
To learn more details on how to complete the connection, please refer to the application help.
Some copy protected media contents may not play on the external displays via Intel WiDi.
Changing the external playback settings
After one or more external displays are connected, the operating system can automatically detect, identify and setup the display settings.
You can also manually manage how the external displays will work and change the display settings by pressing P while holding down the
Windows ( 
) key. If you disconnect the external display before you turn the computer's power off, be sure to switch to the internal display.
When you change the display output device, the audio playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the audio playback device manually by the following steps:
1.Click Start
2.In the Playback tab, select the playback device which you want to switch to.
3.To use the internal speakers on your computer, select Speakers. To use the television or the external monitor that you have connected to the computer, select a different playback device.
4.Click the Set Default button.
5.Click OK to close the Sound dialog.
TOSHIBA
In addition to the ports available on the computer, the TOSHIBA
The Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the Port Replicator to a power source.
You must connect the AC adaptor before you connect to a Port Replicator.
The ports on the Port Replicator may have higher priority than the ports on the docked computer.
When you use external display ports on the Port Replicator or on your computer, some software may show different type of ports which you connected.
When connecting an AC Adaptor to the Port Replicator, use only the AC Adaptor included with Port Replicator. Do not use the computer???s AC Adaptor.
Refer to the Port Replicator???s User's Manual for more details.
To dock your computer in the Port Replicator, follow the steps below:
1.Align the top left and top right corner of your computer to the correct mark on the Port Replicator.
2.Press down on the back of the computer until it clicks into place. The computer connector on the port replicator engages the computer???s docking port.
When the computer is connected, the Docked light on the Port Replicator glows green while the computer is powered on.
Figure
1 
1. Docking port (computer)
Product appearance depends on the model you purchased.
Make sure the AC adaptor is always connected to the TOSHIBA Hi- Speed Port Replicator III 180W/120W while in use. Otherwise the Port Replicator will stop working, possibly resulting in data loss.
Some models support multiple display function if equipped with a TOSHIBA
The port replicator supports a maximum of two external displays. For each VIDEO panel, only one port can function at a time.
TOSHIBA Docking Station Utility
Models with a docking port support system sleep undocking operation.
You can enable/disable the system sleep undocking operation. If enabled, the computer goes into Sleep Mode when you undock the computer.
You can undock the computer in one of the following ways: Press the Eject button on the port replicator.
Click Start, select Undock from the Shut down options.
Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and select Eject Docking Station.
To access the utility, click Start
System sleep undocking operation will function under the following conditions:
Select Do nothing for When I close the lid by clicking Start
Control Panel
Choose what closing the lid does.
TOSHIBA Dock setting is currently set to Enable.
The computer???s lid is closed.
After closing the computer lid, wait a few seconds before pressing the Eject button on the port replicator, otherwise the system may not go to sleep.
Unexpected undocking may cause data loss on connected storage device(s).
After an unexpected undock, there may be some delay before the system goes into sleep mode.
Security lock
A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Please refer to the instructions for the product you are using for more information.
Connecting the security lock
In order to connect a security cable to the computer, follow the steps as detailed below:
1.Turn the computer so the security lock slot faces you.
2.Align the security cable with the lock slot and secure it in place.
Figure
2
Product appearance depends on the model you purchased.
Optional TOSHIBA Accessories
You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer:
Universal AC Adaptor If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.
TOSHIBA
details.
Sound System and Video mode
This section describes some of the audio control functions.
Volume Mixer
The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows.
To launch the Volume Mixer utility, right click on the speaker icon on the Taskbar, and then select Open Volume Mixer from the sub menu. To adjust the volume level of speakers or headphones, move the
Speakers slider.
To adjust the volume level of an application that you are using, move the slider for the corresponding application.
Microphone Level
Follow the steps below to change the microphone recording level.
1.Right click on the speaker icon on the Taskbar, and select Recording devices from the sub menu.
2.Select Microphone, and click Properties.
3.On the Levels tab move the Microphone slider to increase or decrease the microphone volume level.
If you feel the microphone volume level is inadequate, move the
Microphone Boost slider to a higher level.
Audio Enhancements
In order to apply the sound effects for your current speaker, follow the steps below.
1.Right click on the Speakers icon on the Taskbar, and then select
Playback devices from the sub menu.
2.Select Speakers, and click Properties.
3.On the Enhancements tab select the sound effects you would like, and click Apply.
DTS Studio Sound
DTS Studio Sound??? is a premium audio enhancement suite that utilizes revolutionary audio technology to provide the most immersive and realistic listening experience ever offered for a two speaker playback environment.
DTS Studio Sound is provided with some models. It provides the following features:
Advanced audio rendering to match 2D and 3D video content for enveloping surround sound
Accurate placement of audio cues for immersive surround sound from any PC speaker configuration laptop / desktop speakers or headphones
Broad sweet spot with elevated sound image
Maximum volume output delivering maximum volume without creating clipping or distortion
Dialog enhancement for clear and intelligible vocals
Bass enhancement for rich, low frequency production
High frequency definition for crisp details Consistent volume level across content
To access the utility, Click Start
U.S. patents apply to this product. See http://patents.dts.com.Manufactured under license from DTS Licensing Limited.
Realtek HD Audio Manager
You can confirm and change the audio configuration using the Realtek HD Audio Manager. To launch the Realtek HD Audio Manager:
Click Start
When you first launch the Realtek HD Audio Manager, you will see two device tabs. Speakers is the default output device. Microphone is the default input device. To change the default device, click the Set Default Device button under the chosen device tab.
Information
Click the Information button 
to view hardware information, software information, and language setting.
Power Management
The audio controller in your computer can be turned off when the audio function is not used. To adjust the configuration of audio power management, click the Power Management button 
.
When audio power management is enabled, the circle button at the upper left of the Power Management is blue and convex.
When audio power management is disabled, the button is black and concave.
Speaker Configuration
Click the Auto Test button 
to confirm the internal speakers or the headphone sound is coming from the right direction.
Default Format
You can change the sample rate and bit depth of sound.
Video mode
Video mode settings are configured via the Screen Resolution dialog.
To open the Screen Resolution dialog, click Start
Appearance and Personalization
If you are running some applications (for example a 3D application or video playback), you may see some disturbance, flickering or frame dropping on your screen.
If that occurs, adjust the resolution of display, lowering it until the screen is displayed properly.
Chapter 5
Utilities and Advanced Usage
This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities.
Utilities and Applications
This section describes the
The efficient performance might not be expected with multiple user accounts registered.
Only startup from
When system needs to be restarted because of Windows update, drivers update or applications installation, please Shut down or Restart accordingly. If not, those changes will not be reflected to the system properly with
When setting password (e.g. user password, HDD password), please enter it using keyboard.
When the system is booting in
Before using
If you set the
TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously.
TOSHIBA eco Utility helps control the power consumption of your computer. Various information can help you understand your degree of contribution to the environment.
To access this utility, click Start
For details on TOSHIBA eco utility, see the help file.
TOSHIBA HDD/SSD This utility includes wizard functions to monitor Alert Utilitythe Disk Drive operating status and execute the
system backup.
To access the utility, click Start
TOSHIBA Sleep Utility This utility is able to either enable or disable the following function:
Sleep and Charge: By connecting to the USB port, devices such as digital audio players are able to charge, even when the computer is in Standby/Sleep Mode, Hibernation Mode or shutdown state.
To access this utility, click Start
TOSHIBA Service This application allows your computer to Stationautomatically search for TOSHIBA software
updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accordance with the rules and regulations as well as applicable data protection law.
To access this utility, click Start
You may not have all the software listed above depending on the model you purchased.
To access the setup files of the drivers/utilities, Click Start
Special features
The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use.
Access each function using the following procedures.
*1 To access the Power Options, click Start
Display automatic power off *1
This feature automatically cuts off power to the computer's display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options.
HDD automatic power This feature automatically cuts off power to the off *1hard disk drive when it is not accessed for a
specified time, with power being restored when the hard disk drive is next accessed. This can be specified in the Power Options.
System automatic This feature automatically shuts down the system Sleep/Hibernation into either Sleep Mode or Hibernation Mode Mode *1when there is no input or hardware access for a
specified time. This can be specified in the Power Options.
Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer.
Intelligent power supply *1
A microprocessor in the computer's intelligent power supply detects the battery's charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options.
Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the Hard Disk Drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning off the power section, for more details.
USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports.
USB Charge
Your computer can supply USB Bus power (DC5V) to the USB port. The port with the icon ( 
) supports the following feature:
USB Sleep and Charge System ON CDP Charge
USB Sleep and Charge
You can use the Sleep and Charge function to charge certain USB- compatible external devices such as mobile phones or portable digital music players. Your computer can supply USB bus power (DC5V) to the
compatible port even when the computer is turned OFF. "Power OFF" includes Sleep Mode, Hibernation Mode or shutdown state.
To set USB Sleep and Charge feature, click Start
Select the Enable Sleep and Charge check box to enable this function.
The Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification. In those cases, turn the power of the computer ON to charge the device.
When Sleep and Charge function is enabled, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC5V). As for the specifications of the external devices, please contact the device manufacturer or check the specifications of the external devices thoroughly before use.
Using the sleep and charge function to charge external devices will take longer than charging the devices with their own chargers.
If Sleep and Charge function is enabled, the computer???s battery will discharge during hibernation or when the computer is turned off. It is recommended that you connect the AC adaptor to the computer while using Sleep and Charge function.
External devices connected to the USB bus power (DC5V) function that interfaces with the power ON/OFF of the computer may always be in an operational state.
When there is a current overflow of the external devices connected to the compatible ports, USB bus power (DC5V) supply may be stopped for safety reasons.
When Sleep and Charge function is enabled, the USB Wakeup function may not work for compatible ports. In that case, if there is a USB port that does not have the Sleep and Charge function, attach the mouse or keyboard to it. If all USB ports have the Sleep and Charge function, change to disable Sleep and Charge function. The USB Wakeup function will now work, but the Sleep and Charge function will be disabled.
Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag.
Your PC has multiple charging modes so that many different USB devices can be supported for Sleep and Charge function.
Auto Mode (Default) is suitable for a wide range of digital audio players. While using Auto Mode, your computer can supply USB bus power at
maximum 2.0A to the compatible ports while the computer is turned off. When USB device cannot be charged by Auto Mode, change to Alternate Mode.
This function may not be able to be used with some connected external devices even if the appropriate mode is selected. In this situation, disable and stop using this function.
Some external devices cannot use Auto Mode. As for the specifications of the external devices, please contact the device???s manufacture or check the specifications of the external device thoroughly before use.
Always use the USB cable that was included with your USB device.
Enable under Battery Mode
This option can be used to enable/disable sleep and charge under battery mode. It also displays the remaining battery capacity.
Move the slider bar to specify the lower limit. If the remaining battery life falls below the setting, the Sleep and Charge function will be stopped.
System ON CDP Charge
This function enable/disable CDP (Charging Downstream Port) to use rapid USB charge while the computer is powered on. When "System ON CDP Charge Mode" is enabled, your computer can supply USB bus power (DC5V, 1.5A) to the compatible ports while the computer is turned on.
To set System ON CDP Charge Mode, click Start
TOSHIBA
The "System ON CDP Charge Mode" may not work with certain external devices even if they are compliant with the USB specifications. In those cases, use a USB port without "USB Sleep and Charge function" or disable ???System ON CDP Charge Mode???.
It is recommended that AC adaptor be connected to the computer while supplying USB bus power (DC5V, 1.5A).
When your computer battery capacity is too low to continue, "System ON CDP Charge Mode" may not work. In those cases, connect the AC adaptor and reboot the computer.
Always use the USB cable that was included with your USB device.
When "System ON CDP Charge Mode" or ???USB Sleep and Charge function??? is enabled, the ???USB Wakeup??? function may not work. In that case, use a USB port without "USB Sleep and Charge function" or disable
both ???System ON CDP Charge Mode??? and ???USB Sleep and Charge function???.
TOSHIBA Password utility
The TOSHIBA Password Utility provides two levels of password security: User and Supervisor.
Passwords set by the TOSHIBA Password Utility function are different from the Windows password.
User Password
To start the utility, point to or click the following items:
Start
User authentication may be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords, etc.
Set (button)
Click this button to register a password. After a password is set, you will be prompted to enter it when you start the computer.
After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy diskette or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place.
When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or
When entering a password, do not enter any characters (for example "!" or "#") produced by pressing the SHIFT or ALT keys and so on.
Delete (button)
Click this button to delete a registered password. Before you can delete a password, you must first enter the current password correctly.
Change (button)
Click this button to change a registered password. Before you can change a password, you must first enter the current password correctly.
Owner String (text box)
You can use this box to associate text with the password. After you enter text, click Apply or OK. When the computer is started, this text will be displayed together with the prompt asking you to enter a password.
You can launch the TOSHIBA Setup Utility to set, change or delete the HDD Password or HDD Master Password.
If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your HDD, or for any other losses to you or any other person or organization that result from the loss of access to your HDD. If you can???t accept this risk, don???t register the HDD User Password.
When saving the HDD User Password shut down or restart the computer. If the computer is not shut down or restarted, the saved data may not be correctly reflected. For more information on shutting down or restarting the computer, refer to Turning on the power.
Supervisor Password
If you set a Supervisor Password, some functions might be restricted when a user logs on with the User Password.
You can start the Supervisor Password utility by accessing the following folder and then
C:\Program Files\TOSHIBA\PasswordUtility\
or
C:\Program Files (x86)\TOSHIBA\PasswordUtility\
This utility lets you do the following:
Register or delete the Supervisor Password.
Specify restrictions for general users.
Starting the computer using a password
If you have already registered a user password, there is one way to start the computer:
Enter the password manually.
The password is necessary only if the computer was shut down in Hibernation mode or boot mode. It is not needed in Sleep mode and Restart.
To enter a password manually, follow the steps as detailed below:
1.Turn on the power as described in the Getting Started section. The following message will appear in the screen:
Password=
At this point, the function keys do not work. They will function after you enter the password.
2.Enter the Password.
3.Press ENTER.
If you enter the password incorrectly three times in a row, or if you don???t enter the password within 1 minute, the computer shuts down. In this case, some features that can power on the computer automatically
TOSHIBA HWSetup
TOSHIBA HWSetup is the TOSHIBA configuration management tool available through the Windows operating system.
To run TOSHIBA HWSetup, click Start
The TOSHIBA HWSetup window contains a number of tabs to allow specific functions of the computer to be configured.
In addition there are also three buttons: OK, Cancel and Apply.
Some options shown in grey are possible to confirm their status.
TOSHIBA HWSetup screen may have the following tabs:
Boot
The settings or options explained here may vary depending on the model you purchased.
After you changed the settings, a dialog box may appear to prompt you that the changes will take effect after the computer is restarted. Make sure to restart your computer immediately to apply these changes.
TOSHIBA PC Health Monitor
The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and the system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers, and will track specific activities related to the computer and their usage.
The collected information includes device operation time and number of actuations or status changes (i.e.: number of power button and FN key combination uses, AC adaptor, battery, LCD, fan, HDD/SSD, sound volume, wireless communication functionalities and USB information), date of initial system use, and also computer and device usage (i.e.: power settings, battery temperature and recharging, CPU, memory, backlight illumination time, and temperatures for various devices). The stored data uses a very small portion of the total hard disk capacity, approximately 10MB or less per year.
This information is used to identify and provide a notification of system conditions which may effect the performance of your TOSHIBA computer. It may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA's authorized service providers. Additionally, TOSHIBA may also use this information for quality assurance analysis.
Subject to the use restrictions above, the HDD data logged may be transferred to entities located outside of your country or region of residence (e.g., European Union). Those countries may or may not have the same data protection laws or data protection levels as required by your home country or region.
Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel. Doing so will automatically delete all collected information from the HDD/SSD.
The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA's obligations under its standard limited warranty in any way. TOSHIBA's standard limited warranty terms and limitations apply.
Starting the TOSHIBA PC Health Monitor
The TOSHIBA PC Health Monitor can be started using the following methods:
Click Start
Click the icon (
) in the notification area, then click the "Enable PC Health Monitor..." message the first time you run the application and "Run PC Health Monitor..." every time thereafter.
No matter which method is used, the TOSHIBA PC Health Monitor explanation screen will be displayed.
Clicking Next will display the "PC Health Monitor Software Notice & Acceptance" screen. Please carefully read the information displayed. Selecting ACCEPT and clicking OK will enable the program. By enabling the TOSHIBA PC Health Monitor software, you agree with these terms and conditions and to the use and sharing of the collected information. Once the program is enabled, the TOSHIBA PC Health Monitor screen is displayed, and the program will begin monitoring system functions and collecting information.
A message will be displayed if any changes which may interfere with the operation of the program are detected. Follow the instructions displayed on screen in the message.
Using the Hard Disk Drive (HDD) Protection
Some models have the function for reducing the risk of damage on the hard disk drive.
Using an acceleration sensor built into the computer, HDD Protection detects vibration shocks and similar signs of movement of the computer, and automatically moves the Hard Disk Drive head to a safe position to reduce the risk of damage that could be caused by
HDD Protection function does not guarantee that the hard disk drive will not be damaged.
During audio/video playback, when the computer detects a shock or vibration and the hard disk drive's head is parked, the playback might be temporarily interrupted.
HDD Protection cannot be used in models that are equipped with SSD.
When vibration is detected, a message will be displayed on the screen, and the icon in the Taskbar notification area will change to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state.
Taskbar icon
TOSHIBA HDD Protection Properties
You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click
Start
HDD Protection
You can choose whether to enable or disable TOSHIBA HDD Protection.
This function does not work when the computer is booting, in Sleep Mode, in Hibernation Mode, in transition to Hibernation Mode, recovering from Hibernation Mode, or powered off. Do not subject the computer to vibration or impact while the function is disabled.
Detection Level
This function can be set to four levels. The sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF, 1, 2 and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used in a mobile environment or in other unstable conditions, setting the detection level to 3 could result in frequent execution of TOSHIBA HDD Protection, which will slow Hard Disk Drive reading and writing. Set a lower detection level when the speed of Hard Disk Drive reading and writing is a priority.
Different detection levels can be set depending on whether the computer is used as handheld or mobile usages, or whether it is used in a stable environment such as on a table in the workplace or at home. By setting different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode.
3D Viewer
This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer.
When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop. When the head is
The 3D Viewer can be started from the icon in the task tray.
This 3D object virtually represents the Computer's internal Hard Disk Drive. This representation may vary from the actual number of disks, disk rotation, head movement, part size, shape and direction.
This feature may use a large amount of CPU and memory on some models. The computer may become slow or sluggish when attempting to run other applications while the 3D Viewer is displayed.
Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer.
Details
To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window.
Detection Level Amplification
When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
HDD Protection Message
Specify whether to display a message when TOSHIBA HDD Protection is active.
TOSHIBA Setup Utility
TOSHIBA Setup Utility is a BIOS setup utility that provides you a menu- based user interface so that you can easily view and change BIOS settings.
To enter the TOSHIBA Setup Utility, follow the steps below:
1.Press and hold the F2 key, and then turn on the computer - TOSHIBA Setup Utility will load.
2.Follow the
System Recovery
There is a hidden partition allocated on the Hard Disk Drive for the System Recovery Options in the event of a problem.
You can also create recovery media and restore the system. The following items will be described in this section:
System Recovery Options
Creating Recovery Media
Restoring the
Restoring the
System Recovery Options
The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system.
See the Windows Help and Support content for more information about
Startup Repair.
The System Recovery Options can also be run manually to repair problems.
The procedure is as follows. Follow the instructions shown on the on- screen menu.
1.Turn off the computer.
2.While holding the F8 key, turn on the computer.
3.The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press ENTER.
4.Follow the
Check your Windows?? manual for more information on backing up your system (including the system image backup feature).
Creating Recovery Media
This section describes how to create Recovery Media.
Be sure to connect the AC adaptor when you create Recovery Media.
Be sure to close all other software programs except the Recovery Media Creator.
Do not run software such as screen savers which can put a heavy load on the CPU.
Operate the computer at full power. Do not use
Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.
Do not use utilities, including those intended to enhance Hard Disk Drive access speed. They may cause unstable operation and damage data.
Do not shut down/log off or Sleep/Hibernate while writing or rewriting the media.
Set the computer on a level surface and avoid places subjected to vibrations such as airplanes, trains, or cars.
Do not use on an unstable surface such as a stand.
A recovery image of the software on your computer is stored on the Hard Disk Drive, and can be copied to either disc media or USB Flash Memory by using the following steps:
1.Select either blank disc or USB Flash Memory.
The application will allow you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory.
Please note that some of the disc media may not be compatible with the optical disc drive connected to your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding.
USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding.
2.Turn on your computer and allow it to load the Windows operating system from the Hard Disk Drive as normal.
3.Insert the first blank disc into the optical disc drive tray, or insert the USB Flash Memory into one available USB port.
4.Click Start
5.After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.
Restoring the
If the
When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
1.Load the Recovery Media into the Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port.
2.Turn off the computer's power.
3.While holding down F12 key on the keyboard, turn on your computer - when the TOSHIBA Leading Innovation >>> logo screen appears, release the F12 key.
4.Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media.
5.A menu will be displayed from which you should follow the
If you have previously chosen to remove the recovery partition and are trying to create "Recovery Media", you will see the following message: "The Recovery Media Creator can not be launched because there is no recovery partition."
When there is no recovery partition, the Recovery Media Creator cannot make Recovery Media.
However, if you have already created a "Recovery Media", you can use it to restore the recovery partition.
If you have not created "Recovery Media", please contact TOSHIBA support for assistance.
Restoring the
A portion of the total Hard Disk Drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore
If you subsequently set up your Hard Disk Drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.
In addition, if you use a
Make sure that the AC adaptor is connected during the restoring process.
When you reinstall the Windows operating system, the hard disk may be reformatted and all data may be lost.
1.Turn off your computer.
2.While holding down 0 (zero) key on the keyboard, turn on your computer.
3.Follow the on screen instructions to finish the recovery
Chapter 6
Troubleshooting
TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause.
All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Problem solving process
Resolving problems will be much easier if you observe the following guidelines:
Stop immediately when you recognize a problem exists as taking further action may result in data loss or damage, or you may destroy valuable problem related information that can help solve the problem.
Observe what is happening - write down what the system is doing and what actions you performed immediately before the problem occurred. Make a screenshot of the current display.
Please also be aware that the questions and procedures described in this chapter are meant only as a guide, they are not definitive problem solving techniques. In reality many problems can be solved simply, but a few may require help from TOSHIBA Support - if you find you need to consult others, be prepared to describe the problem in as much detail as possible.
Preliminary checklist
You should always consider the simplest solution first - the items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem:
Make sure you turn on all peripheral devices before you turn on the computer - this includes your printer and any other external device you are using.
Before you attach an external device you should first turn the computer off, then when you turn the computer back on again it will recognize the new device.
Make sure all optional accessories are configured properly in the computer's setup program and that all required driver software has been loaded (please refer to the documentation included with the optional accessories for further information on its installation and configuration).
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors.
Inspect all connecting cables for loose wires and all connectors for loose pins.
Check that your disc media is correctly loaded
Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
Analyzing the problem
Sometimes the computer will give you clues that can help you identify why it is malfunctioning. In view of this you should keep the following questions in mind:
Which part of the computer is not operating properly - keyboard, HDD/ SSD, display panel, Touch Pad, Touch Pad control buttons - as each device will produce different symptoms.
Check the options within the operating system to ensure that its configuration is set properly.
What appears on the display? Does it display any messages or random characters? Make a screenshot of the current display and, if possible, look up the messages in the documentation included with the computer, software or operating system.
Check that all connecting cables are correctly and firmly attached as loose cables can cause erroneous or intermittent signals.
Do any indicators light, if so, which ones, what color are they and do they stay on or blink? Write down what you see.
Do you hear any beeps, if so how many, are they long or short and are they high pitched or low pitched? In addition, is the computer making any unusual noises? Write down what you hear.
Record your observations so you can describe them in detail to TOSHIBA Support.
Before using a peripheral device or application software that is not an authorized TOSHIBA part or product, make sure the device or software can be used with your computer. Use of incompatible devices may cause injury or may damage your computer.
If something goes wrong
Your computer does not respond to the keyboard commands
If an error occurs and the computer does not respond to your keyboard commands, follow the steps below:
Press the power button and hold it down for five seconds. Once the computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button.
Your program stops responding
If you are working with a program that suddenly freezes all operations, chances are the program has stopped responding. You can exit the failed program without shutting down the operating system or closing other programs.
To close a program that has stopped responding:
1.Press CTRL, ALT, and DEL simultaneously (once), then click Start Task Manager. The Windows Task Manager window appears.
2.Click the Applications tab. If a program has stopped responding, the words "not responding" appear beside its name in the list.
3.Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with the next step.
4.Close the remaining programs one by one by selecting the program name, then End Task. Closing all programs should allow you to continue working. If it does not, power off your computer and then restart it.
The computer will not start
Make sure you attached the AC adaptor and power cord/cable properly.
If you are using the AC adaptor, check that the wall outlet is working by plugging in another device, such as a lamp.
Verify that the computer is on by looking at the Power indicator.
If the indicator is glowing, the computer is on. Also, try turning the computer off and then on.
If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator. If the indicator is glowing, the computer is connected to a live external power source.
Hardware and system checklist
This section discusses problems caused by your computer???s hardware or attached peripherals. Basic problems may occur in the following areas:
Power
When the computer is not plugged into an AC power outlet, the battery pack is the primary power source. However, your computer also has a number of other power resources, including an intelligent power supply and a Real Time Clock (RTC) battery, all of which are interrelated with any one having the ability to produce apparent power problems.
Overheating power down
If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shut down to prevent any damage - in this instance all unsaved data in memory will be lost.
AC power
If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN/Battery indicator. Please refer to the Power Condition Descriptions section for further information.
Battery
If you suspect a problem with the battery, you should check the status of the DC IN/Battery indicator.
Battery doesn???t power the computer as long as expected
If you frequently recharge a partially charged battery, the battery might not charge to its full potential - in these instances you should fully discharge the battery and then attempt to charge it again.
Check the Power saver option under Select a power plan in the Power Options.
Real Time Clock
The BIOS setting and system date/ time are lost.
The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the TOSHIBA Setup Utility by using the following steps:
1.Press and hold the F2 key, and then turn on the computer - the TOSHIBA Setup Utility will load.
2.Set the date in the System Date field.
3.Set the time in the System Time field.
4.Follow the
Keyboard
Keyboard problems can be caused by the setup and configuration of the computer - please refer to the The Keyboard section for further information.
Internal display panel
Apparent computer's display panel problems may be related to the computer's setup and configuration.
HDD
Memory Media Card
For further information, please refer to Operating Basics.
Pointing device
If you are using a USB mouse, you should also refer to both the USB mouse section and the documentation supplied with your mouse.
Problem
Procedure
In this instance the system might be busy - Try moving the mouse again after waiting a short while.
Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure it is firmly attached.
If you are still unable to resolve the problem, contact TOSHIBA Support.
USB device
In addition to the information in this section, please also refer to the documentation supplied with your USB device.
USB device does not Remove the USB device from the computer and workthen reconnect it to a free port in order to ensure it
is firmly attached.
Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation.
Sleep and Charge function
For more information and settings, please refer to the USB Charge section.
Sound system
In addition to the information in this section, please also refer to the documentation supplied with your audio device.
External monitor
Please also refer to Operating Basics, and to the documentation supplied with your monitor for further information.
LAN
Wireless LAN
Bluetooth
TOSHIBA support
If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance.
Before you call
Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first. Before contacting TOSHIBA, try the following:
Review troubleshooting sections in the documentation supplied with your software and/or peripheral devices.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance.
Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for current information and support.
TOSHIBA technical support
If you are still unable to solve the problem and suspect that it is hardware related, visit TOSHIBA technical support website http://www.toshiba.co.jp/ worldwide/.
Chapter 7
Appendix
Specifications
This section summarizes the computer???s technical specifications.
Physical Dimensions
Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased.
316 (w) x 227 (d) x 15.9/19.9 (h) millimeters (touch screen models)
Environmental Requirements
Power Requirements
External RGB monitor port pin assignment
I/O (I): Input to computer
I/O (O): Output from computer
AC Power Cord and Connectors
The power cord???s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications:
Certification agencies
In Europe, two conductors power cord must be VDE type,
For the United States and Canada, two pin plug configuration must be a
The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
Information for Wireless Devices
Wireless Technology Interoperability
The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to:
The IEEE 802.11 Standard on Wireless LANs (Revision a/b/g/n or b/g/ n), as defined and approved by the Institute of Electrical and Electronics Engineers.
Bluetooth?? Modules are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:
Bluetooth Specification (depending on the model you purchased), as defined and approved by the Bluetooth Special Interest Group.
Logo certification with Bluetooth wireless technology as defined by the Bluetooth Special interest Group.
This Bluetooth product is not compatible with devices using Bluetooth Version 1.0B specifications.
The wireless devices have not completed verification of connection and operation with all devices which are using the Wireless LAN or Bluetooth radio technology.
Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth
and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection.
If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN.
Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module.
In Europe visit
Wireless Devices and your health
Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because Wireless products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless products are safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of Wireless products may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the Wireless products equipment on board of airplanes, or
In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless device prior to turning on the equipment.
Wireless LAN Technology
The computer???s wireless communication function supports some wireless communication devices.
Only some models are equipped with both Wireless LAN and Bluetooth functions.
Do not use the Wireless LAN
Turn all wireless functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction for your medical device when using any wireless functionality.
Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.
It may not be possible to make a network connection to a specified network name using the ad hoc network function. If this occurs, the new network (*) will have to be configured for all computers connected to the same network in order to
* Please be sure to use new network name.
Security
TOSHIBA strongly recommend that you enable encryption functionality, otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data.
TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof.
Card Specifications
Radio Characteristics
Radio Characteristics of Wireless LAN module may vary according to:
Country/region where the product was purchased
Type of product
Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the
Band 2.4GHz
The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.
The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid
Range is also impacted due to "obstacles" in the signal path of the radio that may either absorb or reflect the radio signal.
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range.
Bluetooth wireless technology
Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers, printers and mobile phones. When it is enabled, Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.
You cannot use the computer's
Security
Two advanced security mechanisms ensure a high level of security:
Authentication prevents access to critical data and makes it impossible to falsify the origin of a message.
Encryption prevents eavesdropping and maintains link privacy.
Worldwide operation
The Bluetooth radio transmitter and receiver operate in the 2.4GHz band, which is
Radio links
You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a
Bluetooth Stack for Windows by TOSHIBA
Please note that this software is specifically designed for the following operating systems:
Windows 7
Information regarding the use of this software with these operating systems is listed below, with further details being contained with the electronic help files supplied with the software.
This Bluetooth Stack is based on the Bluetooth specification, depending on the model you purchased. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers.
Release Notes related to the Bluetooth Stack for Windows by TOSHIBA
1.Fax application software: Please be aware that there is some fax application software that you cannot use on this Bluetooth Stack.
2.
Product Support:
The latest information regarding operating system support, language support or available upgrades can be found on our web site http://
Radio Regulatory Information
The Wireless device must be installed and used in strict accordance with the manufacturer???s instructions as described in the user documentation that comes with the product. This product complies with the following radio frequency and safety standards.
Europe
Restrictions for Use of
Restrictions for Use of
To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4GHz and 5GHz channel limitations apply for outdoor usage. The user should use the wireless LAN utility to
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation.
Canada - Industry Canada (IC)
This device complies with
Ce dispositif est conforme ?? la norme
Les dispositifs fonctionnant dans la bande
Les utilisateurs devraient aussi ??tre avis??s que les utilisateurs de radars de haute puissance sont d??sign??s utilisateurs principaux
The term ???IC??? before the equipment certification number only signifies that the Industry Canada technical specifications were met.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Refer to the FCC information section for the detailed information.
Caution: Exposure to Radio Frequency Radiation
The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits. Nevertheless, the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized.
In the usual operating configuration, the distance between the antenna and the user should not be less than 20cm. Please refer to the computer user???s manual for the details regarding antenna location.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada???s website
Caution: Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range.
Taiwan
Using this equipment in Japan
In Japan, the frequency bandwidth of 2,400MHz to 2,483.5MHz for second generation
1. Important notice
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and
stations for mobile object identification systems (RFID) used in factory production lines (Other Radio Stations).
1.Before using this equipment, ensure that it does not interfere with any of the equipment listed above.
2.If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
3.Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations.
2. Indication for Wireless LAN
The indication shown below appears on this equipment.
(1)(2) (3)(4)
(5)
1.2.4 : This equipment uses a frequency of 2.4GHz.
2.DS : This equipment uses
3.OF : This equipment uses OFDM modulation.
4.4 : The interference range of this equipment is less than 40m.
5.
: This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz. It is possible to avoid the band of mobile object identification systems.
3. Indication for Bluetooth
The indication shown below appears on this equipment.
(1) (2) (3)
1
(4)
1.2.4 : This equipment uses a frequency of 2.4 GHz.
2.FH : This equipment uses
3.1 : The interference range of this equipment is less than 10m.
4.
: This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
4. About the JEITA
5GHz Wireless LAN supports W52/W53/W56 Channel.
Device Authorization
This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of
Intel?? Dual Band
The Name of the radio equipment: 7260NGW DSP Research, Inc.
Approval Number: D130021003
Intel?? Dual Band
The Name of the radio equipment: 3160NGW DSP Research, Inc.
Approval Number: D130092003 The following restrictions apply:
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.
Radio approvals for wireless devices
This equipment is approved to the radio standard by the countries/regions in the following table.
If you use this equipment in the countries/regions which are not listed in the table below, please contact TOSHIBA Support.
As of September 2013
NFC Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
RF Exposure Information
This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission for an uncontrolled environment.
Canada - Industry Canada (IC)
This device complies with Industry Canada
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le pr??sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris??e aux deux conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radio??lectrique subi, m??me si le brouillage est susceptible d'en compromettre le fonctionnement."
IC RF Exposure Information
This equipment complies with IC
Legal Footnotes
Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis.
CPU
Central Processing Unit (CPU) Performance Legal Footnotes.
CPU performance in your computer product may vary from specifications under the following conditions:
use of certain external peripheral products
use of battery power instead of AC power
use of certain multimedia, computer generated graphics or video applications
use of standard telephone lines or low speed network connections
use of complex modeling software, such as high end computer aided design applications
use of several applications or functionalities simultaneously
use of computer in areas with low air pressure (high altitude >1,000 meters or >3,280 feet above sea level)
use of computer at temperatures outside the range of 5??C to 30??C (41??F to 86??F) or >25??C (77??F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - contact TOSHIBA support for details).
CPU performance may also vary from specifications due to design configuration.
Under some conditions, your computer product may automatically shut- down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make
Certain
Memory (Main System)
Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities. The amount of main system memory allocated to support graphics may vary depending on the graphics system, applications utilized, system memory size and other factors.
If your computer is configured with more than 3 GB memory, the memory might be displayed as approximately 3 GB only (depending on the computer???s hardware specifications).
This is correct because the operating system usually displays the available memory instead of the physical memory (RAM) built into the computer.
Various system components (like the video adapter???s GPU, etc.) require their own memory space. Since a
Computers configured with a
Battery Life
Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is a normal phenomenon for all batteries. To purchase a new battery pack, see the accessories information that is shipped with your computer.
HDD/SSD Capacity
1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more
LCD
Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Graphics Processing Unit (GPU)
Graphics processing unit (GPU) performance may vary depending on product model, design configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode.
Total Available Graphics Memory is the total of, as applicable, Dedicated Video Memory, System Video Memory and Shared System Memory. Shared System Memory will vary depending on system memory size and other factors.
Wireless LAN
The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
The actual transmission speed will be lower than the theoretical maximum speed.
Copy Protection
Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media.
Glossary
The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Abbreviations
Index
A
AC adaptor additional
DC IN 19V jack
B
Battery
extending life
types
Battery indicator
Bluetooth
Bluetooth Stack for
Windows by Toshiba
C
Cleaning the computer
Cooling vents
D
DC IN/Battery indicator
Display
Documentation list
Dual Pointing Device
AccuPoint
Touch Pad
E
Equipment checklist
External monitor problems
F
FN + 1 ( reduce)
FN + 2 (enlarge)
FN + 3 (Volume down)
FN + F1 (Lock)
FN + F2 (Power Plan)
FN + F4 (Hibernate)
FN + F5 (Output)
FN + F6 (Brightness Down)
FN + F7 (Brightness Up)
FN + F9 (Touch Pad)
FN + space (Zoom)
K
Keyboard
Function keys F1...F12
Windows special keys
L
LAN
cable types
M
Media care
Card care
Memory card care
Memory installing
memory media card
Password power on
Starting the computer by password
user
Pointing Device
Power
conditions
Shut Down mode
Problems
AC power
Analyzing the problem
Dual Pointing device
HDD
Internal display panel
Memory Media Card
Overheating power down
Power
Real Time Clock
R
Recovery hard disk drive
Recovery Media
Restarting the computer
S
SD/SDHC/SDXC Card formatting
Security lock
Sleep Mode setting
System automatic
Smart Card inserting
Sound system problems
T
TOSHIBA HDD/SSD Alert
Utility
