FULLY AUTOMATIC
WASHING MACHINE
Thank you for purchasing TOSHIBA Fully Automatic Washing Machine.
???Please read this manual carefully in order to operate the machine properly.
???Sometimes you may find some water remaining in the drainage hose at your first operation. This is caused by the
to worry about.
OWNER???S MANUAL
22/10/08, 11:12
WARNING
WARNING: This indicates an important item where incorrect operation may lead to injury or death.
Never attempt to touch laundry in the spin basket until the motion of the basket stops completely.
Laundry in the basket may become wrapped around the hand, even when the basket is only moving slowly.
Use particular caution when children are present.
Never operate washing machine by young children and infirm person.
This washing machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been adequately supervised by a responsible person to ensure that they can use the washing machine safety.
Never allow children to look into the basket or play around the washing machine. Young children should be supervised to ensure that they do not play with the washing machine.
Do not place the stand or box near the washing machine.
Children may fall into the tub and get injured or drowned.
Never disassemble or modify the machine.
It can cause fire or electrical shock or malfunctions that lead to injuries.
Consult the store you bought the machine.
Use proper power source which indicated in the rating label of the machine.
It can cause fire or electrical shock.
Failure to use a proper power source may result in the electrical outlet becoming excessively hot, leading to fire.
Unplug the power cord from the electrical outlet before attempting to service the washing machine.
Do not handle the power cord with wet hands.
It can cause electrical shock or malfunctions that lead to injuries.
Never use damaged electrical cords or plugs or loose socket.
It can cause electrical shock or malfunctions that lead to injuries or fire.
Do not damage the electrical power cord.
Do not attempt to damage, cut, or modify the power cord, or subject it to excessive bending, pulling, twisting, or binding. Also, do not yank the metal portion, place heavy objects on the cord, or pinch the cord. Doing so may damage the cord, resulting in fire or electrical shock.
Do not install in a bathroom or in area exposed to the elements.
Doing so may result in electrical shock or shorts.
Do not allow water to come into direct contact with the various parts of the outer body.
Doing so may result in electrical shock or shorts.
Do not place flammable materials in the basket.
Do not put kerosene, gasoline, benzene, thinners, alcohols, or the like, or any laundry articles soaked in such materials, in the basket.
It can cause explosion or fire.
Wipe away any buildup of dust or grime on the prongs of the
Buildup of dust or grime may cause fire.
Do not close the fire on plastic parts.
It can cause fire.
Make sure that water drains properly.
Using the washing machine with faulty drainage may cause water to back up within the machine, leading to electrical short or fire.
2
CAUTION
CAUTION: This indicates an important item where incorrect operation may lead to injury or material damage.
Do not pull the cord when unplug the appliance.
Hold the plug body to unplug.
It can cause electrical shock or malfunctions that lead to injuries.
Do not use water with temperatures over 50??C.
Water that is too hot can cause malfunctions and deformation of the machine, which may result in electrical shock.
Do not attempt to wash or rinse waterproofed sheets, mats, or clothing.*
Doing so may cause abnormal vibration or injury during the spin cycle.
*: This includes raincoats, fishing gear (jackets and waders), ski wear, sleeping bags, etc.
Do not climb or place heavy objects on the washing machine.
Doing so may result in injury due to bending or breakage.
Pull out the power plug if you do not plan to use the machine for a long time.
Failure to do so may result in electrical shock or shorts due to deterioration of the insulation.
Do not place the hands or other objects under the washing machine while in operation.
Moving parts may cause injury.
Before use, make sure the faucet in open, and the connection with water supply hose is not loose or leakage water.
Looseness of screws, hose connections, or other areas may cause water leakage or other damage.
The opening must not be obstructed by carpeting when the washing machine is installed on a carpet floor.
DESCRIPTION OF PARTS
Softener Dispenser
Bleach Dispenser
Lint Collector
Basket (WASH/SPIN)
3
DESCRIPTION AND OPERATION OF PANEL PARTS
CHILD PROOF MODE DISPLAY
???Check this to see if the CHILD PROOF mode is ON (lit) or warning (flashing).
???PRESET??? button
???You can set/reset the CHILD PROOF mode.
???You can set the time until washing finished.
???SUPER SPIN DRY??? button
PROCESS DISPLAY
???Operating process is indicated by flashing. Remaining process is indicated by lightening.
???COURSE??? button
???You can select the program suitable for the laundry.
???SELECT??? button
???Select either the WASH, RINSE, or SPIN cycle as you desire.
???START/HOLD??? button
???Press this pad when you want to start.
???Press this pad when you want to hold.
???POWER??? button
???Press this button to power off/on.
???Power is automatically turned off about 15 seconds after the end of operation, or about 10 minutes later if the operation is not on.
WATER LEVEL
DETERGENT GUIDE
???The amount of supply using the measure spoon accompanying the compact detergent is displayed.
One spoonful of detergent denotes about 55L of water consumption
Depending on the kind of detergents, amount of water consumption by one spoonful changes. Adjust the detergent volume according to the particular detergent in use.
???Illumination shifts to the direction where the
higher water level is indicated as the result of pushing the 
button.
???While using the "tub cleaning" program, the
water level will be automatically at High and the 
button cannot be used.water level can be obtained.
RESUME FUNCTION (POWER FAILURE RECOVERY)
2 1
4
If a power failure occurs during operation, the washer memorizes the remaining process. After the electricity recovers, you can resume it.
1 Turn the POWER on.
??? The progress and course indicators of the remaining process will be flashing, and the buzzer sounds for 5 seconds.
2 Press the 
button.
NOTE ??? For ???PRESET MODE??? , if the power failure occurs before the machine starts operating, the machine will cancel the preset time. Therefore, you have to reset the time.
??? Press the 
button to clear the remaining process.
CHILD PROOF MODE (if you have small children)
CHILD PROOF mode
This model is equipped with CHILD PROOF mode. After this mode is set to ON, the washer will alarm you if the lid is opened during operation. If you find accident such as falling of child into wash tub, please take necessary safety action urgently.
If there is small children who requires attention, set this mode ON.
WARNING: Pay attention to small children. Do not leave the lid opened. Do not leave the washer filled with water. Never allow children to look into the basket or play around the washer. Do not place the stand or box etc. near the washer.
HOW TO USE CHILD PROOF MODE
If the CHILD PROOF mode is set to ON and the lid is opened while the washer is in operation, it beeps the buzzer, stops water supply and stops wash/spin operation. If there is water in the tub, the washer drains water. (The buzzer keeps beeping alarming unexpected operation is happening).
CHILD PROOF INDICATOR
If there is small child, set this mode ON.:
if this mode is set to ON and the lid opened during operation, the buzzer beeps, the indicator flashes, the washer stops water supply and stops wash/spin operation, and drains water from wash tub approximately 5 seconds of the lid opening.
???If the CHILD PROOF mode is set off temporary, do not forget to turn the CHILD PROOF mode ON again.
???When started operation with lid opened and the CHILD PROOF mode on, the washer will beeps and drains water.
???The washer memorizes the last setting of CHILD PROOF mode when powered off.
???The CHILD PROOF mode is set to ???OFF??? when shipped out from the factory.
TO SET/RESET CHILD PROOF MODE
TO SET CHILD PROOF MODE:
1 With pressing ???PRESET??? button, press ???START/HOLD??? to turn the CHILD PROOF mode on.
*Buzzer beeps and the CHILD PROOF indicator lights on. (Check the indicator lights on.)
TO TURN CHILD PROOF MODE OFF:
2 With pressing ???PRESET??? button, press ???START/HOLD??? to turn the CHILD PROOF mode.
*Buzzer beeps and the CHILD PROOF indicator turns off.
TO PUT ADDITIONAL LAUNDRY/
DETERGENT:
Open the lid, throw laundry/detergent into the wash tub and close the lid quickly. (The washer starts draining approx. 5 seconds after the lid opening.)
WHEN THE WASHER IS BEEPING AND
STARTS DRAINING WATER.
Check for safety.
Press POWER button to OFF.
PRESET MODE
How to use preset mode
TO SET/RESET PRESET MODE
1 Turn the POWER on.
???Put the laundry in the basket and select your favorite cycle or water level. Set the custom wash cycle.
2 Press PRESET button for preset time.
???Change 9, 6 to off with pressing.
???
TO CONFIRM PRESET TIME
???Display preset time when you open the wash lid, or press PRESET button.
???Finished time is different between preset and actual time with water pressure and drain condition.
POWDER DETERGENT
Spread a handkerchief on the laundry, and then put on the detergent not to spill from the handkerchief.
LIQUID DETERGENT
Pour the liquid detergent into the bleach dispenser.
CAUTION
Cause by remained detergent as follows:
???Wet detergent.
???Wet clothes or put in detergent directly on clothes.
5
HOW TO OPERATE
Preparation
"REGULAR" "SOAK" "SPEED" "HEAVY" "DELICATE"
"REGULAR" cycle
Water level, water current and time are auto- matically selected according to the quantity and type of laundry detected automatically.
Put the laundry evenly and confirmly.
If it is not, the lower water level may be set.
"SOAK" cycle
This method is used to wash clothing which easily absorbs stain and clothes with noticeable stains.
???The time requirement is 1 hour.
???Rinsing is set to "OVERFLOW RINSE".
When you press 
once, "OVERFLOW RINSE" will be canceled.
"SPEED" cycle
It is especially for light soiled clothes.
It washes with regular water current mode and shorter washing time.
"HEAVY" cycle
It is especially for heavy soiled clothes.
It washes with stronger water current mode and longer washing time.
"DELICATE" cycle
This course is for delicate clothes such as blouse or lingerie to wash gentlely with very mild water flow.
Cloth Weight : 2kg or less.
1 Turn the POWER on.
???Turn the POWER on, "REGULAR" cycle and "CONDENSED WASH" is selected automatically.
CONDENSED WASH
The washer starts flowing water at the low level to absorb the concen- trated detergent into the laundry in order to remove the dirt efficiently.
2 Put the laundry in the basket.
???In case of much laundry, soak the laundry completely in the water to prevent the splash on feeding water.
???In case of selecting "SUPER SPIN DRY", please see page 7 for details.
3 Press 
button to select "REGULAR" "SOAK" "SPEED" "HEAVY"
or "DELICATE".
???The pulsator automatically detects the laundry amount, and indicates the amount of concentrated detergent suitable for the laundry amount.
5 Put in the detergent according to the detergent guide.
6 Close the lid.
???If you start the lid opening, cycle stops before spin.
???Avoid your finger caught when closing the lid.
Cycle end
The power turn off automatically.
??? A "beep" sound will be heard when operation is finished.
After stopping the basket, put the laundry in it.
???If the CHILD PROOF mode is set to ON, and the lid is opened while the machine is in operation, the buzzer beeps and the CHILD PROOF indicator flashes then the machine starts draining water.
If you wish to turn off the end buzzer sound
??? You can turn off the buzzer sound.
???With pressing "COURSE" button, press to turn on the power switch. After buzzer beeps 3 times, the end buzzer disabled.
???As you reset, set the same way.
???Once you set it, the washing machine will remember the mode set, and no need to set each time.
6
Type and amount which may be washed.
Single size
(140 cm x 200 cm or less)
100% synthetic fiber
type: Mayer, Tuft, Down cloth
Weight: 2.8 kg or less
???All wool blankets and regular electric blankets should NEVER be washed.
Washable electric blankets should be washed according to the washing instruction given in the user???s manual that ac- company them when purchased.
???If the blanket will not go into washing net because of fiber length of thickness, it cannot be washed.
The amount of laundry/once of spin
Less than 1.5 kg
Setting time for spinning
???You can manually set the time of spinning according to the following guide:
If you would like to shorten the time of drying clothes in the room: 30 min.
If you would like to dry the synthetic clothes: 90 min.
The clothes which cannot be performed spin drying
Folding blankets
??? Remove waste or
Fold it once again the same way.
Insert a blanket to the net
???Roll up the blanket.
???Roll the blanket up loosely except Mayer type blanket.
???Place the blanket into the blanket net
Allow the hem of the blanket to ex- tend about 10 cm.
1 Turn the POWER on and put the laundry in the basket.
Washing period may become longer with drain- age condition.
1 Turn the POWER on.
2 Put the detergent and press the START button.
Put the detergent amount matches for HIGH in spite of displaying detergent volume for LOW.
???After operate 3 and 4 minutes and a detergent melts, cut the POWER off.
???Do not use soap powder.
3 Put the blanket in basket.
???Place the blanket in net and put into the basket with the fastenerside on top.
???Dip a blanket in washing liquid sufficiently.
4 Set the regular cycle.
Press 
once to set to ???OVERFLOW RINSE???. Press 
to set 45L water level.
5 Close the lid and press the START button.
Take the blanket out after washing completed.
???Open the blanket net fastener and put at the center of the blanket. Then take out the blanket from net.
???The pulsator will operate before the water is let into the basket. The washer will estimate the amount of laundry and display the detergent amount (while the lid is open).
5 Put the detergent as the display and close the lid.
???If the lid is open during the operation, the washer will stop before washing and spinning.
After the operation: the buzzer will beep when the washer completes the operation.
??? Turn off the faucet and clean the lint collector.
7
CUSTOM WASH CYCLES
"OVERFLOW RINSE" cycle
OVERFLOW RINSE cycle compared to normal washing, is one rinse more (total 3 times) and last rinse becomes overflow rinse.
??? When set once, it is written in memory and starts with overflow rinse from the next time.
You can select the operation that you want ??? such as spin only or rinsed water reuse.
The process cannot be changed after pushing the START. Turn the POWER supply off and on in order to change course.
1 Turn the POWER on.
Put the laundry in the basket and select your favorite cycle or water level.
2 Set the custom wash cycle.
3 Close the lid and press the START button.
???To use drain only, leave the lid open.
After error display appears, turn the power off.
If you wish to change the shower rinse to the static rinse
SHOWER RINSE CYCLE means during stirring, flowing water and rinsing are executed simultaneously.
When flowing water amount is small, the tank may not be filled up.
For the shower rinse, it needs twice for the process.
But for the static rinse, it needs only once.
1Press 
button.
2Press the 
button and hold for 5 seconds.
The buzzer sound will be heard and the course will be set within 5 seconds. After that, turn off the washer.
8
LAUNDRY GUIDE
Recommended detergent amount
???Put the laundry in the washer basket, push the START button, rotate the pulsator without water to detect the laundry amount.
Then it indicates the amount of detergent required.
??? Indicates one measuring spoon of the concentrated detergent is required.
???The detergent amount differs with the type of the detergent.
???Too much detergent causes frothily or insufficient rinse.
???The water level slightly differs according to the particular type of laundry.
When using liquid detergent and bleach
Liquid detergent and bleach
Pour liquid detergent into the bleach dispenser with watered down double.
Pour it into the bleach dispenser slowly, being careful not to split it, while the water fills for the wash cycle.
When using powered bleach, add it directly into the basket.
Caution
???Colored and dyed fabrics may lose their color if washed in bleach, so be sure to consult the instructions on the bleach container before washing.
???Do not apply chloric bleach directly to laundry items.
???Do not allow bleach to spill on the control panel. If you spill bleach, wipe it away.
When using softener
1Add softener to the softener dispenser at the top of the basket, and close the softener dispenser lid.
???If the basket is situated so that filling with softener is difficult, turn the basket to
2Wash as described on page 5 ~ 7.
???Softener will be dispensed automatically.
???The amount of softener varies with the 
brands. Follow the instruction on the softener label.
Caution
???You cannot see the softener poured into the dispenser while rinsing. Because it moves to the three parts in the case for using the centrifugal force at spinning.
???Softener effectiveness is reduced when OVERFLOW
RINSE is used.
???Do not open the lid while spinning. The softener dispensation timing will be thrown off and effectiveness reduced.
???Do not leave the washing machine idle for long periods while filled with softener.
???Pour the concentrate softener after watering down triple.
If you feel the water amount is less or much
Water level is automatically set to suit the laundry amount. If you feel the water amount is less or much, you can adjust it by following.
Turn the POWER on with pressing WATER LEVEL button.
Turn off the POWER. (Finished adjusting)
* Set it once, it is written in memory. You don???t have to set it on each laundry.
9
MAINTENANCE
Lint collector
Clean the lint collector after every use.
1Remove the lint collector by lifting it up. When the machine has stopped in a place in which it is difficult to lift the lint collector out, turn the basket by hand to a more convenient place and remove the lint collector.
2Remove the lint by turning the lint collector inside out.
3Replace the lint collector.
??? In the event that the net is damaged,consult your nearest dealer.
Softener case
If this occurs, remove the case, immerse in warm water (less than 40??C) for 10 minutes, and replace after dried well.
Washing machine body and panel
Before performing any maintenance on your washing machine, be sure to remove the electrical plug from its power source.
The main body and control panel may be cleaned by wiping with a soft cloth soaked in water.
Caution: Never clean the body or control panel with benzine, thinner, cleanser, or other chemical cleaners. Use of such chemicals can discolor or damage parts.
Cleaning the tub
"TUB CLEANING" course
The dirt from clothes or wastewater on the wash/spin basket will cause the smell or the problem of water draining. Such dirt from the washing process will then make the laundry dirty. If you are in such case, please use "Tub Cleaning" program once a month. Or in case the clothes have been starched, please use the "Tub Cleaning" program to remove the dirt of the starch from the basket.
???Normally use detergent.
???The amount of detergent must be more than the guided Standard Detergent Amount.
???Do not use "Tub Cleaning" program continuously.
???If there is a great amount of dirt inside the basket, you had better use the
Please follow the instruction labeled on the cleaner bag.
L "Tub Cleaning" Process
1Turn the POWER on.
2Press the COURSE button and select
TUB CLEANING.
3Press the START button.
???During the "Tub Cleaning" program, only the TUB CLEANING indicator will light on.
4When the pulsator (spinning board) starts to spin, add the
???Do not put any clothes in the basket during the "Tub Cleaning" program.
5Close the lid.
???If the lid is opened during the operation, the operation will stop before the draining and rinsing process.
Finish "Tub Cleaning" process.
??? Beeping when the operation is finished.
10
INSTALLATION
Choosing an installation location
???It is dangerous to place the washing machine in an unstable location, since it may move during vibration.
???It will increase the sound produced by the machine when it vibrates during use.Install your washing machine in a level, stable place.
When you move washing machine, hold the handles on the sides.
There are moving parts, electrical parts and steel plates
???Never touch on the cabinet bottom by hands. Never lift at the cabinet bottom by hands.which may cause electrical shock or injury.
When the machine is covered.
Do not use the cover made of chloric vinyl. Sometimes it damages resinous parts and painted surface. When you use the cover made of chloric vinyl, put the cloth between the machine and the cover.
Avoid place where the machine is exposed to direct sun- light.
??? Plastic parts may become deformed or discolored.
Avoid places where the machine may become frozen during cold weather.
Allow a space of at least 5 cm from the sides and rear of
???When placed too near to walls or other objects, the
vibration of the machine during operation may cause them to shake.the machine to the nearest vertical object.
Allow 5 cm
Installing the bottom cover
Put the bottom cover into the bottom of the washing machine, and fix the bottom cover with screws.
F R ONT
BOTTOM C OVE R (LE FT)
BOTTOM C OVE R (R IG HT) S UP P OR T P LATE
Installation
Adjust the legs so that the body of your washing machine is level. (The two legs are adjustable.)
11
INSTALLATION
Installing the ground pin
??? The ground pin in the plug should be connected to the proper point of the socket for grounding.
Installing the drainage hose
Moving the hook
???When inserting the drainage hose into a wash pan or onto a drain pipe, the hook may be moved to facilitate the installation.
???When hooking the hose hook into the slot provided on the body of your washing machine,
Drainage hose extension
???Pay close attention to the height of the drainage hose and articles over which it passes. If the drainage hose is too high, proper drainage may not be obtained.
???The length of the
Caution:
???If the level of the threshold and the drainage hose is high, the washing machine may not be drained.
15 cm or less
???Be careful not to rub the drainage hose. Do not insert the drainage hose under the washing machine. They may be damaged the drainage hose.
Concrete block
Drainage hose
Moving the drainage hose The drainage hose can be installed on either the right or left side.
The connector port for the drainage hose is found on the right side of the washing machine, but it can be changed without disconnecting the internal hose from the drainage valve.
1 Remove the back cover, then grip the stopper securing the internal hose with your fingers and pull it up.
2 Turn the nut for the drainage hose connector port counterclockwise.
3 Pull the internal hose from inside the washing machine to detach.
4 Remove the hose hole cap on the
Stopper
Nut
Tap
Hose hole cap Upper and lower notches
in the hose hole
5 Turn the stopper 180??C without removing from hose. Insert the stopper into the securing hole on the left side of the outer shell and press down to secure the internal hose.
Drainage valve
Stopper
6 Attach the back cover, and fit the hose hole cap over the hose hole on the
place, then from outside put the nut in place and turn clockwise to secure.
Outer shell
Nut
7 After moving the drainage hose, be sure to testoperate the washing machine, ensuring that there are no water leaks or unusual noises.
12
INSTALLATION
Attaching the water supply hose to the faucet
Faucet shape
The distance is needed 1.6 cm or more
Caution
??? The old inlet hose should not be reused.
??? If the faucets are not suited, please contact your
water for your washing machine, it is suggested
that a branching water pipe (available separately) be used.
Attaching the hose union
Hose Union
Lock lever
Water supply hose
Sleeve
??? If the gap is wide, it may cause the water leak.
Inside ring
Ring
Approx. 4 mm
Joint seal
??? If it cause the water leakage during operation, tighten the nozzle more securely.
Caution
???If you attach the hose union again because of moving house etc., loose the gap is approx. 4 mm between the nozzle and the
ring. Then attach it according
Connecting the water supply hose
1Pull the sleeve down, then insert the water supply hose.
2Separate the sleeve until a click is heard, then push it up.
3Check to ensure that the lock lever is hung on the nozzle. Next, check to ensure that the water supply hose does not come off by pulling down on it.
Lock lever
4Tighten the hose nut on the end of the
water supply hose Nozzle securely to the water
intake valve.
Water intake valve
Caution
???Check to ensure that the water supply hose is properly installed by turning the water on and checking for leakage.
If there is leakage, connect it from the first.
???If you remove the water supply hose after supplying water, water may splash. Refer to the following
??? ???Removing the water supply hose???.
If the filling water becomes not good
The water inlet may be blocked by foreign objects. Remove the water supply hose and clean the filter with a brush.
???If you remove the water supply care- lessly, water may splash.Therefore, use the following procedure.
Filter
Water intake valve
Removing the water supply hose
1Turn the water faucet off.
2Turn the power switch ON and press the START/HOLD pad.
3After indicating the water level, loosen the hose nut of the machine top and remove it.
13
BEFORE CALLING THE SERVICEMAN
Error Indication List
In the case the buzzer sounds and the select display flash alternatively.
The display of "LINEAR WATEL LEVEL" indicates the error condition as shown below.
???Is the drain water frozen?
???Is the outlet of the drainage hose sunk in water?
???Is the drainage hose clogged?
14
BEFORE CALLING THE SERVICEMAN
The following are not malfunctions.
HANDLING METHOD FOR EMERGENCY
When the machine takes on abnormal operation, please disconnect the power plug and send it to our service agency for handling. Never disassemble the machine by yourself, for safety reasons.
SPECIFICATIONS
15
MANUFACTURED BY