Version 3.0 Series
This guide explains how to install and configure the Toshiba
It is strongly recommended that you add only one camera at a time to the network for configuration.
1 Prerequisites
Before the configuration begins, check the following:
The camera is unpacked and correctly connected to the power source and network. If using a Wired LAN connection, confirm that the network LAN is plugged in.
If using a wired network, make sure to plug in the network cable to the camera before powering the camera on. If the network cable is not connected during
WebCCTV NVR is installed, activated, running and properly connected to the network (see Installation manual).
You have an exact list of IP addresses and passwords for WebCCTV NVR and the network cameras.
The IP address of WebCCTV NVR is properly configured (see Installation manual). Monitor, keyboard and mouse are connected to WebCCTV NVR (see Installation manual).
If Java 2 Runtime Environment SE Ver.1.4.2 is not installed , this product may not output images or sound properly. Access the following website to download ???Java 2 Runtime Environment SE??? http://java.com
The IP address of the camera and the IP address of the computer you will use for the network camera configuration are in the same range. The default camera network settings are as follows:
IP address: 198.162.0.30, Subnet mask: 255.255.255.0
If your computer address is not in the range 198.162.0.n please change it appropriately.
Make sure that IP address of the camera and the IP address of the computer you will use for the network camera configuration are in the same range. After the configuration is complete, make sure that the IP address of WebCCTV/GuardNVR server and the IP address of the camera are in the same range.
Version 3.0 Series
2 Camera configuration
To begin the configuration of the camera you should use the Camera Finder application. Camera Finder is an application for searching network cameras. You can use it by downloading it from the Toshiba website on the following link: http://www.toshiba.com/taisisd/security/support/support_dloads.jsp
2.1 Searching and entering the camera.
To configure ?? camera follow the steps below:
1.Download Camera Finder using the link above. Open the Setup file and follow the onscreen instructions to install the Camera Finder application.
2.After the installation is complete, go to
Camera Finder Screen
Version 3.0 Series
3.On this screen click Search button. All cameras, which are currently connected to the network, appear.
Make sure that the IP addresses of a camera and computer, which you launched Camera Finder from, are in the same range.
4.Choose the camera you want to login to from the list and click Administrator button to login as administrator.
Camera Administrator Login Screen
5.In the browser screen that appeared specify default administrator credentials as follows: Login ID: root, Password: ikwb.
6.Click Login button.
Version 3.0 Series
2.2 Network settings configuring
Camera Network Settings Screen
1.After you have logged in go to Network
Specify Camera Name
Switch Auto Identification of Other Camera to OFF
Switch DHCP to OFF.
Specify IP address and Subnet Mask
Specify Default Gateway IP address
HTTP Port Number leave as default - 80
Contact your system administrator to obtain all required network parameters.
It is important to assign an IP address statically, not using a DHCP service, in order to properly reference the camera from WebCCTV software.
2. Click Save button.
Version 3.0 Series
2.3 Administrator credentials configuring
To change administrator credentials do the following:
1. Go to Administrator
Changing Administrator Credentials Screen
2. Specify current Login ID and Password in the corresponding fields.
Default administrator credentials are:
Login ID: root
Password: ikwb
3.Specify new Login ID
4.Specify new password and confirm it in the corresponding fields.
5.Click Save.
Use these credentials while adding the camera to WebCCTV software.
Version 3.0 Series
3 Advanced camera configuration
Quadrox recommends implementing the following settings:
1. Go to Camera
Camera Settings Screen
2.You may not change Camera Picture Size, it is adjustable from WebCCTV software.
3.You may choose Picture Quality you want, but please note higher picture quality consumes more bandwidth.
4.You may not change Frame Rate, it is adjustable from WebCCTV software.
5.You may choose Installation Environment depending on a camera location.
6.AE compensation, Auto B/W, Shutter Speed are advanced exposure settings, configure them if you are an experienced user!
7.Auto Slow Shutter ??? must be OFF! (ON by default)
8.Auto Sensitivity Boost ??? must be OFF! (ON by default)
9.You may configure Sound Sensitivity.
10.Click Save button.
If you changed the computer IP address before camera configuration ??? don???t forget to put it back.
Version 3.0 Series