INSTRUCTION MANUAL
3 CCD CAMERA
IK-TF2
For Customer Use
Enter below the Serial No. w h i c h i s l o c a t e d o n t h e bottom of the cabinet. Retain this information for future ref- erence.
Model No.: IK-TF2
Serial No.:
WARNING
This is a Class A of EN55022 product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu- ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil num??rique de la classe A est comforme ?? la norme NMB-003 du Canada.
SAFETY PRECAUTIONS
Read the following safety precautions carefully before using this product. These instructions contain valuable information on safe and proper use that will prevent harm and damage to the operator and other persons. Make sure that you fully understand the following details (indications, graphic sym- bols) before proceeding to the remaining sections in this manual.
Indication definitions
*1: Catastrophic bodily injury means loss of eye- sight, burns (high and low temperatured),
Graphic symbol definitions
?????? indicates a prohibited action that must not be carried out. The actual prohibited action is indicated in the symbol or nearby graphically or de- scribed in text.
?????? indicates a mandatory action that must be carried out. The actual instruction is indicated in the sym- bol or nearby graphically or de- scribed in text.
shock, fracture, poisoning, etc. which leaves a sequela and require hospitalization or prolonged treatment.
*2: Bodily injury means injuries, burns and electric shock which does not require hospitalization or prolonged treatment.
*3: Property damage means extended harm to home, household effects, domesticated animals, and pets.
Warning
???Stop operation immediately when any abnormality or defect occurs.
Use during an abnormal condition; such as emitting smoke, burning odors, damage from dropping invasion of foreign objects, etc. may cause fire and/or electric shock. Be always sure to disconnect the power plug from the electrical outlet (socket) at once and contact your dealer.
??? Avoid installing in a shower room or a bathroom.
This may cause fire and/or electric shock.
??? Do not operate in places with possibility of becoming wet.
This may cause fire and/or electric shock.
???Do not repair, disassemble and/or modify by yourself.
This may cause fire and/or electric shock. Be always sure to contact your dealer for internal repair, check and cleaning of the product.
???Use the specified power supply.
Otherwise, a fire or an electric shock may occur.
???Don???t place things or materials on the unit.
Ingress of foreign materials such as metallic things and liquid into the unit may cause a fire or an electric shock.
???Do not put the product in an unstable, slanting and/or vibrated place.
Drop and/or fail of the product may cause injury.
???Do not touch the power cord or other connection cables during a thunderstorm.
This might cause electric shock.
Caution
???Note the following instructions when installing.
???Do not put an inflammable material on the product.
???Do not put the product on an Inflammable material such as carpet or blanket.
??? Do not block a vent hole.
???Do not put the product in a narrow space, since the heat generated from the product may be difficult to emanate.
If you do not follow the above, the heat generated by the product may cause fire.
???Do not put the product in direct sunshine and/or high temperature.
The temperature inside the product may cause fire.
???Avoid setting in humid, smoky, vaporized or dusty places. A fire or an electric shock
may occur in such places.
This may cause fire and/or electric shock.
???Do not point the lens directly at the sun and/or intensive light such as direct sun-
light, etc.
Focusing of the light may cause injury of eye and/or fire.
???Do not put the product in your mouth or swallow any parts.
This may cause suffocation and/or injury.
???Ask your dealer to perform a periodical check and internal cleaning (approx. once
every five years).
Dust inside the product may cause fire and/or trouble. For check and cleaning cost, please consult your dealer.
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user in any of the following cases:
1.Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten- tional or accidental; use under extreme operating conditions.
2.Malfunction or non-function resulting in indirect, additional or consequential damages, including but not limited to loss of expected income and suspension of business activities.
3.Incorrect use not in compliance with instructions in this instruction manual.
4.Malfunctions resulting from misconnection to other equipment.
5.Repairs or modifications made by the user or caused to be made by the user and carried out by an unauthorized third party.
6.Notwithstanding the foregoing, Toshiba???s liabilities shall not, in any circumstances, exceed the purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays, distributes, or exhibits an image picked up by a television camera without permission from the copy- right holder. Please also note that transfer of an image or file covered by copyright is restricted to use within the scope permitted by the Copyright Law.
1???CAUTIONS ON USE AND INSTALLATION
???Carefully handle the units.
Do not drop, or give a strong shock or vibration to the camera. This may cause problems. Treat the camera cables carefully to prevent cable problems, such as cable breakdown and loosened connections.
???Do not shoot intense light.
If there is an intense light at a location on the screen such as a spot light, a blooming and smearing may occur. When intense light enters, vertical stripes may appear on the screen. This is not a malfunction. Ghosts may occur when there is an intense light near the object.??? In this case, change the shooting angle.
???Install the camera in a location free from noise.
If the camera or the cables are located near power utility lines or a TV, etc. undesirable noise may appear on the screen. In such a case, try to change the location of the camera or the cable wiring.
???Moire
When thin stripe patterns are shot, stripe patterns that are not actually there (moire) may appears as interference stripes. This is not a malfunction.
???Operating ambient temperature and humidity.
Do not use the camera in places where temperature and humidity exceed the specifications. Picture quality will lower and internal parts may be damaged.
Be particularly careful when using in places exposed to direct sunlight. When shooting in hot places, depending on the conditions of the object and the camera (for example when the gain is increased), noise in the form of vertical strips or white dots may occur. This is not a malfunction.
???Handling of the protection cap.
Keep the protection cap away from children. Children may put them into mouth or swallow them accidentally. The protection cap protects the image sensing plane when the lens is removed from the camera, do not throw away.
???When not using the camera for a longtime.
Stop supplying power.
???When cleaning the camera
Always turn off the power and clean with a piece of soft dry cloth. Do not use benzine, alcohol, thinner, household detergents, chemically treated cloths, etc. If used, coating and printed letters may be discolored. When cleaning the lens, use a lens cleaning paper, etc.
???Avoid using or storing the camera in the following places:
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places contacting chemicals (such as pesticides), rubber or vinyl products for a long period of time.
3???ITEMS CONTROLLED BY USING ON SCREEN DISPLAY
???
shutter Electronic
balance White Gain
Process
Option Sync
5???1 Standard Connection
DC power supply
5???2 Cautions on Connection
??? When connecting the camera cables, be sure to turn off the camera and the other equipment connected.
??????We suggest using a C mount lens made for a 3CCD camera.
When using another lens, the best camera performance of this camera may not be obtained. (For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare, ghost or shading may occur)
Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which has projection dimension from the mounting base of less than 0.157???(4mm).
???For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounding type AC adaptor with the specifications described below.
Power supply voltage
Current rating
Ripple voltage
Connector
???DC12V???10%
???More than 830mA, Less than2.5A
???Less than 50mV???p???p???
???HR10A???7P???4S by HIROSE electronics Co. Ltd Pins 1, 2 ??? 12V
Pins 3, 4 ??? GND
5???3 Connector Pin Assignments
DC IN 12V
1+12V
2+12V
3GND
4GND
6???OPERATION
???Referring to the item ??? 5. CONNECTION???, connect each equipment correctly.
???Turn on the connected equipment and the camera.
???Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc..
???Referring to the item ???6.1 White Balance???, operate the adjustment.
???Referring to the items ???6.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY???, select the necessary items.
6???1 White Balance
For the white balance adjustment for this unit, AWB (Automatic White Balance) and MANUAL (Manual white balance) adjustments are provided. Referring to the items ???7.2 (3) WHT BAL (White balance), 7. MODE SETTING BY ON SCREEN DISPLAY???, select the desired mode.
???AWB(Automatic white balance)
???Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary. (Refer to the item ???7.2 (3) WHT BAL (White balance)???.) 3200K???Appropriate for indoor shooting.
5600K???Appropriate for outdoor shooting.
???If the index menu/menu is displayed, press the [DISP] button to disable the color bar pattern or the character display on the menu.
???Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.
???The character AWB blinks on the screen when the AWB starts.
???The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
???MANUAL(Manual white balance)
???Set the MODE to MANUAL on the WHT BAL menu. (Refer to the item ???7.2 (3) WHT BAL (white balance)???.)
???Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a waveform monitor.
(Refer to the item ???7.2 (3) (3.2) Changing each setting in MANUAL mode???.)
- 11 -
6???2 Gain
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.
For the gain adjustment of the unit, MANUAL (Manual) and OFF (0 dB) modes are provided. Select the mode on the GAIN menu. (Refer to the item ???7.2 (2) GAIN (Video gain)???.)
???MANUAL(Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from ???3dB to 18dB in 1dB steps. (Refer to the item ???7.2 (2) (2.1) (a) Changing the gain in MANUAL mode???.)
???OFF
Gain is fixed at 0 dB.
6???3 Shading Correction
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the screen. In this case, the shading correction can decrease the color shading. For the shading correction of the unit, MANUAL (Manual shading correction) and OFF (no shading correction) modes are provided. Select the mode on the PROCESS menu. (Refer to the item ???7.2 (4) (4.5) Changing shading correction mode???.)
???MANUAL(Manual Shading)
Perform the correction amount setting on the PROCESS menu, confirming with a monitor or a waveform monitor. (Refer to the ???7.2 (4) (4.6) Changing the manual shading correction setting???.)
???OFF
The status is no shading correction.
*The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with SHADING OFF for variable lens conditions.
7???MODE SETTING BY ON SCREEN DISPLAY
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized when the power is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to be set.
7???1 Using the Menues
When the power turns on, the normal screen showing only the video signal appears. Change the output
to each screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], and
[MENU DOWN] buttons.
*A menu is selected when pushing the [PAGE] button after moving the ????????? on the screen by the [MENU UP], [MENU DOWN] button while the Index menu is displayed.
???????????????????????????
??????????????????????????????
???????????????????????????
???????????????????????????
???????????????????????????
??????????????????
7???2 Menus
???Select the menu to change the setting by referring the item ???7.1 Using the Menus???.)
???When the [MENU UP], [MENU DOWN] buttons are pushed, the ????????? on the screen moves up and down. Move the ????????? to the item to change.
( 1 ) SHUTTER???Electronic shutter???
The electronic shutter has three modes; MANUAL, SS(Synchro. Scan), EXT TRIG(External trigger).
Press the ???Page??? button to enter the Shutter Page. Use the ???Data Up/Down??? buttons to select the Shutter Mode.
???1???1??? Changing each setting in MANU mode
<MODE = MANUAL>
(a)Changing the shutter speed
???Set the ????????? to MANU by pushing [MENU UP], [MENU DOWN] buttons.
???Set the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b)Changing the CCD storage mode
???Set the ????????? to FLD/FRM by pushing [MENU UP], [MENU DOWN] buttons.
???Select either FLD (field) or FRM (frame) by pushing [DATA UP], [DATA DOWN] buttons.
???1???2??? Changing each setting in SS???synchro. scan???mode
<MODE = SS >
(a)Changing the shutter speed setting
???Set the ????????? to SYNCHRO SCAN by pushing [MENU UP], [MENU DOWN] buttons.
???Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b)Changing the CCD storage mode
???Set the ????????? to FLD/FRM by pushing [MENU UP], [MENU DOWN] buttons.
???Select either FLD (field) or FRM (frame) by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras become: fixed pattern noise, white pixels, etc.
???1???3??? Changing each setting in EXT TRIG mode
The EXT TRIG has three modes; 1PULSE SNR, 1PULSE SR, 2PULSE.
First set the ????????? to MODE and select EXT TRIG, then set the ????????? to EXT TRIG and select the desired EXT TRIG mode.
???1???3???1??? Changing each setting in 1PULSE SNR mode
(a)Changing inputting trigger pulse setting
???Set the ????????? to TRIG PULSE by pushing [MENU UP], [MENU DOWN] buttons.
*This setting is only valid in the 1PULSE mode (1PULSE SNR and 1PULSE SR). To make the trigger pulse setting when using the 2PULSE mode, first set the EXT TRIG mode to 2PULSE, then make the settings with the TRIG PULSE items.
(b)Changing 1PULSE exposure time setting
???Set the ????????? to EXPOSURE by pushing [MENU UP], [MENU DOWN] buttons.
???Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.
* When or is selected, EXPOSURE cannot be set. (EXPOSURE setting turns OFF.)
Exposure time is automatically controlled by the trigger pulse width.
???1???3???3??? Changing each setting in 2PULSE mode
(a)Changing inputting trigger pulse setting
???Set the ????????? to TRIG PULSE by pushing [MENU UP], [MENU DOWN] buttons.
*This setting is only valid in the 2PULSE mode. To make the trigger pulse setting when using the 1PULSE mode, first set the EXT TRIG mode to 1PULSE SNR or 1PULSE SR, then make the settings with the TRIG PULSE items.
(b)Changing the CCD storage mode
???Set the ????????? to FLD/FRM by pushing [MENU UP], [MENU DOWN] buttons.
???Select either FLD (field) or FRM (frame) by pushing [DATA UP], [DATA DOWN] buttons.
???2??? GAIN (Video gain)
GAIN has two modes; MANUAL, OFF.
Set the ????????? to MODE, push the [DATA UP], [DATA DOWN], and select mode among MANUAL, OFF. In the OFF mode, gain is fixed to 0dB.
???2???1??? Changing each setting in GAIN
(a)Changing the gain in MANUAL mode
???Set the ????????? to MANUAL by pushing [MENU UP], [MENU DOWN] buttons.
???Set the manual gain by pushing [DATA UP], [DATA DOWN] buttons.
???3??? WHT BAL(White balance)
WHT BAL has two modes; AWB, MANUAL.
Set the ????????? to MODE, push the [DATA UP], [DATA DOWN], and select mode among AWB, MANUAL.
???3???1??? Changing each setting in AWB(Automatic White Balance) mode
???White balance mode setting AWB, MANUAL
???Color temperature setting 3200K, 5600K
-- 3 WHT BAL --
(a)Changing color temperature setting
???Set the ????????? to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.
???Select either 3200K or 5600K by pushing [DATA UP], [DATA DOWN] buttons.
???3???2??? Changing each setting in MANUAL mode
(a)Changing the red gain
???Set the ????????? to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.
???Set the red gain by pushing [DATA UP], [DATA DOWN] buttons.
(b)Changing the blue gain
???Set the ????????? to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.
???Set the blue gain by pushing [DATA UP], [DATA DOWN] buttons.
???4??? PROCESS
???4???1???Changing master pedestal
???Set the ????????? to M. PED by pushing [MENU UP], [MENU DOWN] buttons.
???Set the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.
???4???2???Changing R pedestal
???Set the ????????? to R. PED by pushing [MENU UP], [MENU DOWN] buttons.
???Set the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.
???4???3???Changing B pedestal
???Set the ????????? to B. PED by pushing [MENU UP], [MENU DOWN] buttons.
???Set the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.
???4???4???Changing White clip
???Set the ????????? to WHT CLIP by pushing [MENU UP], [MENU DOWN] buttons.
???Set the WHT CLIP by pushing [DATA UP], [DATA DOWN] buttons.
???4???5???Changing shading correction mode
???Set the ????????? to SHADING by pushing [MENU UP], [MENU DOWN] buttons.
???Set the SHADING by pushing [DATA UP], [DATA DOWN] buttons.
???4???6???Changing manual shading correction
???Set the ????????? to MANUAL SHADING by pushing [MENU UP], [MENU DOWN] buttons.
???Set the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.
???5??? SYNC
When an external sync signal is input, the display changes from INT (internal sync) to EXT (external sync)
automatically.
???5???1??? Adjusting horizontal phase
???Set the ????????? to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.
???Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.
???5???2???Changing RGB SYNC
???Set the ????????? to RGB SYNC by pushing [MENU UP], [MENU DOWN] buttons.
???Select G, ALL ON or ALL OFF by pushing [DATA UP], [DATA DOWN] buttons.
???6??? OPTION
???RS232C baud rate 9600bps, 19200bps
-- 6 OPTION --
???6???1??? Changing RS232C communication baud rate
???Set the ????????? to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.
???Select either 9600bps or 19200bps by pushing [DATA UP], [DATA DOWN] buttons.
-22 -
???7??? Setting to factory setting status
The contents set of each scene file can be returned to the factory default status (preset status).
(1)If characters are displayed on the screen, press the [DISP] button to disable the character display.
(2)Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.
(3)The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed for approx. 1 second.
7???3 External Sync
When using the unit with an external sync signal, input HD and VD to RGB terminal on the rear panel, or input SYNC to RGB terminal. When the external sync signal is input, the camera automatically switches its sync from the internal sync to the external sync.
The operation is as shown below, depending on the unit???s status and how external sync signals are input.
???1??? External sync signal input conditions
???2??? External sync frequency range
(External sync with HD, VD)
For EIA standard frequency ???Within ???1% (at horizontal sync frequency)
???3??? Using the unit with external sync signal
When adjusting H (horizontal) phase refer to the item ???7.2 (5)(5.1) Adjusting horizontal phase???.
???3???1??? H (horizontal) phase adjustment
Observe the external sync signal and the video signal output waveform of the unit with a dual trace oscilloscope, and adjust H phase so that the H phases match.
External
Sync. signal
Match
the phase.
Camera Video output
???4??? Changing HD/VD input/output
(1)Put off 6 screws both on flank/top of camera chassis.
(2)Change internal switch SJ01(HD/VD).
SJ01
HD/VD OUTPUT
HD/VD INPUT high-impedance
HD/VD INPUT 75 ?? (factory setting)
7???4 Synchro. Scan Operation
The shutter speed can be set by the horizontal scanning period (1H) or by the frame. Also, CCD integration mode can be set.
???1??? Setting by 1H
260/525H to 1/525H stands for the setting by the 1H and the shutter speed can be set by the 1H (63.56ms).
???2??? Setting by the frame
1FRM to 255FRM (at field storage) and 2FRM to 256FRM (at frame storage) stand for the setting (long period exposure) by the frame.
(a) Field storage period
The video signal stored during the frame period set is output as 1 field video image at a frame interval specified.
VD output
Index output
(INDEX)
???2FRM setting???
(b) Frame storage period
The video signal stored during the frame period set is output as 1 frame video image in a frame interval.
VD output
7???5 EXT TRIG (External trigger)
Charge begins to accumulate after the trigger input, and 1 field or 1 frame images are output. There are three modes: 1PULSE SNR, 1PULSE SR and 2PULSE.
The RGB terminal trigger input and index output interface are as shown below.
??????
??????????????????
??????????????????
???1??? 1 PULSE SNR???1 Pulse Sync Non Reset???
Charge begins to accumulate after the trigger input to the RGB terminal, and 1 field images are output.
(a) Rising edge / Falling edge mode
The exposure time is set to 0.02 ms to 16 ms on the menu.
(RGB terminal)
Rising edge mode
Video output
*Image output after 1 V (Trigger pulse doesn???t pass the VD falling.)
*Image output after 2 V (Trigger pulse pass the VD falling.)
*Image output after 2 V (Trigger pulse pass the VD falling.)
A image is output at the first field after the end of the exposure.
*Image output after 1 V (Trigger pulse doesn???t pass the VD falling.)
*Image output after 2 V (Trigger pulse pass the VD falling.)
*Image output after 2 V (Trigger pulse pass the VD falling.)
A image is output at the first field after the end of the exposure.
???2??? 1 PULSE SR???1 Pulse Sync Reset???
Charge begins to accumulate after the trigger input to the RGB terminal, the vertical sync signal is reset and field images are output.
(a) Rising edge / Falling edge mode
The exposure time is set to 0.02 ms to 16 ms on the menu.
Approx. 1.9???s
Exposure period
Exposure end
VD output
Index output
???INDEX???
Video output
11 to 12H
??????
Index output
???INDEX???
??????
Video output
???3??? 2PULSE
Accumulation of charges is started and ended through the trigger pulse input to the RGB terminal, the vertical sync signal is reset and field images are output.
???Frame storage period???
Pulse width mode
VD output
VD output
Video output
Index output
???INDEX???
- 29 -
8???BEFORE MAKING A SERVICE CALL
9???SPECIFICATIONS
???Design and specifications are subject to change without notice.
10???EXTERNAL APPEARANCE DIAGRAM
LIMITED WARRANTY
TOSHIBA CCD CAMERA
Promptly register your product with Toshiba on-line at www.toshiba.com/taisisd. By registering your prod- uct you will be eligible for periodic updates, announcements, and special offers. You will have access to extended warranty options, upgrades (as applicable), useful tips, on-line troubleshooting, and the ability to schedule service on-line if necessary. The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties. These limited warranties extend to the Original End-User ("Your[r]").
Limited One (1) Year Warranty of Labor and Parts
ISD warrants this product and parts against defects in material or workmanship for a period of one year from the date of original retail purchase by the end-user. During this period, ISD will repair or replace a defective product or part with a new or refurbished item. The user must deliver the entire product to an ISD authorized service center. The user is responsible for all transportation and insurance charges for the product to the Service Center. ISD reserves the right to substitute Factory Refurbished Parts and / or Factory Refurbished Product in place of those in need of repair.
Step-by-step Procedures - How to Obtain Warranty Service
[1]Verify operation of the unit by checking the instruction manual
[2]If there is a defect in material or workmanship, contact an Authorized Service Provider within 30 days after the product fails to comply with specifications.
[3]Arrange for delivery of the product to the ISD authorized service center. Products must be insured and securely packed, preferably in the original shipping carton. A letter explaining the defect and a copy of the bill of sale or other proof of purchase must be enclosed with a complete return street address and daytime telephone number. Charges for transportation and insurance must be prepaid by the end-user.
Questions? If you have any questions, please check the Toshiba Imaging Systems Division Web site as follows:
Website: http://www.toshiba.com/taisisd/indmed
Your Responsibility, warranties are subject to the following conditions:
[1]You must retain the bill of sale or provide other proof of purchase.
[2]You must schedule service within thirty days after you discover a defective product or part.
[3]All warranty servicing of this product must be made by a Toshiba ISD Authorized Service Provider.
[4]The warranty extends to defects in material or workmanship as limited above, and not to any products or parts that have been lost or discarded by user. The warranty does not cover damage caused by misuse, accident, improper installation, improper maintenance, or use in violation of instructions furnished by ISD. The warranty does not extend to units which have been altered or modified without authorization of ISD, or to damage to prod- ucts or parts thereof which have had the serial number removed, altered defaced or rendered illegible.
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. WITH THE EXCEPTION OF ANY WARRAN-
TIES IMPLIED BY STATE LAW AS HEREBY LIMITED, THE FOREGOING EXPRESS WARRANTY IS EXCLU-
SIVE AND IN LIEU OF ALL OTHER WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PROD-
UCTS OR PARTS. IN NO EVENT SHALL ISD BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAM- AGES. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply.
No person, agent, distributor, dealer, service station or company is authorized to change, modify or ex- tend the terms of these warranties in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising under this warranty or under any statute, or law of the United States or any state thereof, is hereby limited to one year from the date you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising under state law. Some states do not permit limitation of the time within which you may bring an action beyond the limits provided by state law so the above provision may not apply to user. This warranty gives the user specific legal rights, and user may also have other rights, which may vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
Copyright ?? 2002 Toshiba America, Inc. All rights reserved.
0.4ms 
1ms
16ms
