Toshiba_Digital_Camera

IMPORTANT SAFEGUARDS

1.Read Instructions

All the safety and operating instructions should be read before the product is operated.

2.Retain Instructions

The safety instructions and instruction manual should be retained for future reference.

3.Heed Warnings

All warnings on the product and in the instruction manual should be adhered to.

4.Follow Instructions

All operating and use instructions should be followed.

5.Cleaning

Disconnect this video product from the power supply before cleaning.

6.Attachments

Do not use attachments not recommended by the video product manufacturer as they may cause hazards.

7.Water and Moisture

Do not use this video product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.

8.Accessories

Do not place this video product on an unstable cart, stand, tripod, bracket or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer???s instructions, and should use a mounting accessory recommended by the manufacturer.

9.Ventilation

This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer???s instructions have been adhered to.

10.Power Sources

This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your product dealer.

11.Power-Cord Protection

Power-Supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, screws and the point where they exit from the product.

12.Lightning

For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the video product due to lightning and power-line surges.

13.Overloading

Do not overload power supply and extension cords as this can result in a risk of fire or electric shock.

14.Object and Liquid Entry

Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of kind on the video product.

15.Servicing

Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

16.Damage Requiring service

Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions.

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the video product.

c.If the video product has been exposed to rain or water.

d.If the video product does not operate normally by following the operating instructions in the instruction manual. Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.

e.If the video product has been dropped or the cabinet has been damaged.

f.When the video product exhibits a distinct change in performance-this indicates a need for

service.

17.Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer with the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

18.Safety Check

Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

- 1 -

??? The CAUTION label, shown on the left, is attached on the camera.

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ???dangerous voltage??? within the product???s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING :

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION :

CONNECT 24V AC UL LISTED CLASS 2

POWER SUPPLY.

FIELD INSTALLATION MARKING :

WORDED :???THIS INSTALLATION SHOULD

BE MADE BY A QUALIFIED SERVICE

PERSON AND SHOULD CONFORM TO

ALL LOCAL CODES.???

Note : The camera is indoor used

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party.

- 2 -

1. FEATURES & DESCRIPTION :

IK-DF01A has following function.

(1)Quick install Design- you can manually set the camera direction.

(2)Built in vari-focal lens with auto-iris Focal length 2.8~5.8mm

(3)Incorporated 1/4type CCD image sensor gives high resolution and excellent sensitivity

480 lines horizontal resolution

0.5 lx minimum illumination with smoke cover

(4)50dB Signal-To Noise Patio

(5)Power supply- AC24V or DC12V - This camera automatically detects the power.

(6)BLC, AGC, and Line-Lock (AC24V)

2. Cautions :

(1)In order to protect the camera, avoid placing or using it under direct sunlight, rain or dust.

(2)Avoid touching the CCD sensor with your fingers. If necessary, use a soft cloth moistened with alcohol to wipe off any dust.

(3)When the camera is not in use, keep the lens cap attached to protect the CCD sensor.

(4)Avoid aiming the camera at the sun.

(5)Avoid shooting the camera at intense light. Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen.

However, this is not a malfunction.

(6)Install the camera away from video noise. If cables are wired near electric lighting wires or a TV set, noise may appear in images. In this event, relocate cables or reinstall equipment.

- 3 -

4. PART NAMES & FUNCTIONS :

Knockout

Cut with a knife or scissors and insert the cables through the knockout so the cables will not pinched when installed.

"Bottom" mark

The "Bottom" mark indicates the lens position. The "Bottom" mark should be on the top when installing in a ceiling.

Power Input Cable

Connect the power cable to AC24V or DC12V. (RED:+12, Black:GND)

VIDEO Cable (BNC Tap)

Connect the Video Cable to a monitor or video device. The image is outputted when powered on.

Zoom Lever

Changes the picture range. Its screw design allows locking capability.

Focus Lever

Adjusts the image into focus. Its screw design allows locking capability.

Lens Iris ADJ

Use to compensate for the iris level. Turn towards L (low) for a darker picture. Turn towards H (high) for a brighter picture. Optimum value is adjusted at the default setting.

V Phase ADJ

Adjusts the phase difference between this camera and other cameras when in Line Lock mode.

Installation Holes

Installs camera to ceiling with attached screws.

Lens ADJ Screw

Turn the ring-type screw to adjust the lens pan angle. Fasten and lock it after completing the adjustment.

Mode Setting Switch

1:BLC (Backlight Compensation Control) When switched on, it automatically adjusts to compensate for subjects that are lit from behind.

2:AGC (Auto Gain Control) When switched on, it automatically adjusts the image in relation to the brightness of the subject.

3:DC/AES

Not available for this camera. Be sure to switch to ON.

4: LL (Line Lock)

Use this switch to set the camera synchronization to internal or line lock. Line Lock is available with AC24V only.

Tilt ADJ Screws

Turn the screws to adjust the lens tilt angle. Fasten and lock them after the adjustment completes.

- 4 -

5. CONNECTIONS AND OPERATIONS :

Notes on connecting

???Power plugs connected equipment must be disconnected before installations.

???A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection.

???For details of wiring and operation of equipment to be connected, refer to their operation manuals.

???Coaxial cables for video signals and the power cord are not supplied with the camera.

Refer to the operations manuals of connected equipment for detailed wiring and overall operation instructions.

5-1 Basic connection single system configuration

Video Monitor

24V AC UL Listed Class 2 power supply / 12V DC power supply CAUTION : Never input 24V AC and 12V DC at the same time.

In case of DC12V, connect ???+12??? to red cable and ???GND??? to black cable.

Do not overload power supply

Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power supply, it should be connected to a power supply that allows for at least 5w consumption.

- 5 -

5-2 Line-Lock Control

???Matching the vertical synchronization with the power frequency is called the Line- Lock.

???This function is activated when the SYNC menu is selected to LL.

???When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching.

Video Monitor

VIDEO SWITCHER

CAMERA1

TO AC 24V UL Listed

class 2 power supply

CAMERA2

Note :

???The camera is synchronized to the power frequency of 60??1Hz covering a normal fluctuation of the power frequency. However, the camera may not cover a large fluctuation caused from the power generated by an engine generator, etc.

???It takes about 10 seconds or more until a stable synchronization is obtained after the power is turned on. This is normal, because several seconds are required to stabilize the camera against power noise.

???Refer to ???7. LINE-LOCK PHASE??? for adjustment.

- 6 -

6. Installations :

(1)Turn the cover left to unfasten it.

(2)Connect the cable of the camera and the cable from the designated power supply with respective BNC connectors.

(3)Fix the camera base to the ceiling firmly with the attached 2 screws. Otherwise it might drop and cause injury.

Note :

???The camera???s weight is about 290g.

???The attached screws are designed to install the camera to a board.

When installing to a surface of other materials, prepare the screws to fix it firmly.

???The screw diameter is ??4mm.

6-1 Adjust the Angle of View

(1)The lens direction in pan direction can be adjusted by turning ring 1left to unfasten it without moving the lens. After adjustment, turn the ring 1 right to fasten it.

Note :

???Do not turn the lens over 360??. Otherwise the inner connector may be broken and the image may not appear.

(2)The lens direction at the tilt angle can be adjusted by turning screw 2. After adjustment, turn screw 2 to fasten it.

(3)Adjust the zoom position by turning zoom lever 3. After adjustment, fasten the zoom lever 3.

(4)Adjust the focus by turning focus lever 4. After adjustment, fasten the focus lever 4.

(5)Repeat the adjustments from step (1) to step (4) till the optimum image appears.

-7 -

6-2 Installing to Wall

The camera head at shipping is set for installing the camera to the ceiling. The camera head angle should be changed when installing to a wall.

Camera Head

"Bottom" Mark

Tilt Range

(1) Turn 2 screws of 1 to unfasten the camera head.

Note :

???The camera head is connected to the inside with cable, do not pull it with strength. Otherwise the inner connector may be broken and the image may not appear.

(2)Reverse the camera head 180?? from default setting and install it. The direction of the camera head is shown as above. With the ???Bottom??? mark2 upwards, the tilt range is adjusted as shown above.

(3)Fasten the screw 1 to fix the camera head.

6-3 Installing the Cover

As shown in the illustration, adjust the cover position to the camera???s installation position and turn it right to install it.

- 8 -

7. LINE LOCK PHASE

When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image.

V PHASE CONTROL

8. NOTE ON USE AND INSTALLATION

???Do not aim the camera at the sun

Do not aim the camera at the sun or point it at sun even if you are not shooting.

???Do not shoot intense light

Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction.

???Treat the camera with care

Do not drop the camera or subject it to strong shock of vibration. Otherwise, the camera may malfunction.

???Never touch internal parts

Do not touch the internal parts of the camera other than the parts specified. Otherwise, the camera may malfunction.

???Do not splash water on the camera

Install the camera where the camera can be kept dry. If the camera gets wet, turn off the power and contact your dealer.

???Check the ambient temperature and humidity

Avoid using the camera where the temperature is hotter or colder than specified. Otherwise, the quality of images may deteriorate or internal parts may be affected. Special care is required to use the camera at high temperature and humidity.

???Should you notice any trouble

If any trouble occurs while you are using the camera, turn off the power and contact your dealer. If you continue to use the camera when there is something wrong with it, the trouble may much worse and an unpredictable accident may occur.

-9 -