Toshiba_DVD_Player

Chapter1Introduction

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING : TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USERSERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilat- eral triangle, is intended to alert the user to the presence of uninsulated ???dangerous voltage??? within the product???s enclo- sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is in- tended to alert the user to the presence of important operat- ing and maintenance (servicing) instructions in the literature accompanying the appliance.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user???s authority to operate the equipment.

Chapter1Introduction

)-0/24!.4.3!&%49 ).3425#4)/.3

2EAD THESE INSTRUCTIONS

+EEPETHESETINSTRUCTIONS

(EED ALL WARNINGS

&OLLOW ALL INSTRUCTIONS

$O NOT USE THISUAPPARATUS NEAR WATER

#LEANEONLY WITHNDRYYCLOTH

$O NOT BLOCKKANYYVENTILATION OPENINGS )NSTALL IN

ACCORDANCE WITH THEHMANUFACTURERS

INSTRUCTIONS

$O NOT INSTALL NEARSANYYHEAT SOURCES SUCHUAS

RADIATORS HEATRREGISTERS STOVES ORGOTHER

APPARATUSRINCLUDING AMPLIFIERS THATNPRODUCE HEAT

$O NOT DEFEATATHE SAFETYTPURPOSE OFETHE

POLARIZED OR GROUNDING TYPE PLUG ! POLARIZED

PLUG HAS TWO BLADESTWITH ONE WIDER THAN THE

OTHER !!GROUNDING TYPENPLUG HAS TWOOBLADES

ANDNAATHIRDIGROUNDING PRONG 4HEHWIDEDBLADE OR

THEH THIRDIPRONGOARERPROVIDEDDFOR YOURUSAFETY )F

THEHPROVIDED PLUGIDOES NOT FIT INTO YOUR OUTLET

CONSULTSAN ELECTRICIAN FOR REPLACEMENT OFATHE

OBSOLETE OUTLET

0ROTECT THE POWER CORDCFROM BEING WALKED ON OR

PINCHEDCPARTICULARLY AT PLUGSCONVENIENCE

RECEPTACLES AND THE POINT WHERE THEYHEXIT FROM

THEHAPPARATUS

/NLY USE ATTACHMENTSACCESSORIESESPECIFIEDEBY

THEHMANUFACTURER

5SE ONLYEWITH THE CART STANDTTRIPODOBRACKETTOR

TABLEESPECIFIEDCBYYTHETMANUFACTUREROR SOLD WITH

THEHAPPARATUS 7HEN A CARTTIS USED USE CAUTION

WHEN MOVINGNTHE CARTAPPARATUS COMBINATION TO

AVOIDIINJURYYFROM TIP OVER

5NPLUGLTHIS APPARATUSUDURINGNLIGHTNINGGSTORMS

OR WHENWUNUSED FOR LONGLPERIODS OFSTIME

2EFER ALL SERVICING TONQUALIFIED SERVICE

PERSONNEL 3ERVICING ISNREQUIRED WHENETHE

APPARATUS HAS BEENADAMAGEDEIN ANY WAYSUCH

AS POWER SUPPLYUCORD ORYPLUG ISRDAMAGED LIQUID

HASABEEN SPILLED ORSOBJECTSLHAVEEFALLENLINTO THE

APPARATUSTHETAPPARATUS HAS BEENAEXPOSEDSTO

RAINIOR MOISTUREDOES NOT OPERATE NORMALLYOR

HASABEEN DROPPED

Chapter1Introduction

Precautions

Notes on handling

7Never disconnect the power cord from a wall outlet while the player is turned on, unless it is in an emergency. Doing so may cause malfunction.

7When shipping the player, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.

7Do not use volatile liquids, such as insect spray, near the player. Do not leave rubber or plastic products in contact with the player for a long time. They will leave marks on the ???nish.

7The top and rear panels of the player may become warm after a long period of use. This is not a malfunction.

When not in use

7For usual absence

Be sure to remove the disc from the player and turn off the power.

7Prolonged absence

Unplug the player from a wall outlet. (This will stop the clock. Display ???SETUP MENU??? by pressing SETUP, and reset the clock ( page 50, 57).)

Notes on locating

7Place the player on a level surface. Do not use it on a shaky or unstable surface such as a wobbly table or inclined stand. The loaded disc may dislodge from its proper position and cause damage to the player. Before placing the player, make sure that the surface can stand the weight of the player. Never place the player in a high location to avoid damage to the product or person by an accidental fall of the player.

7When you place this player near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted depending on the condition and location of said equipment. In such an event, place the player as far away much as possible from the TV, radio, or VCR.

7To avoid damage to this product, never place or store the unit in direct sunlight; hot, humid areas; or areas subject to excessive dust, oily smoke, cigarette smoke or vibration.

Notes on cleaning

Use a soft, dry cloth for cleaning.

7Do not use any type of solvent, such as thinner or benzine, as they may damage the surface of the player.

About the volume level

The volume level of some commercial HD DVD and DVD discs may seem lower than that of audio CDs, other software, etc. If you turn up the volume of the TV or ampli???er to play such discs, be sure to turn it back down after playback ???nishes.

Playback restrictions

This owner???s manual explains the basic instructions for this player. Some HD DVD discs or DVD video discs are produced in a manner that allows speci???c or limited operation during playback. As such, the player may not respond to all operating commands. This is not a defect in the player. Please refer to the notes on compatible discs later in this Introduction and to the discussion of DVD playback and features later in this manual.

?????? may appear on the TV screen during operation. ?????? means that the operation is not permitted by the player or the disc.

About software

Because of problems and errors that can occur during the creation of HD DVD, DVD and CD software and/ or the manufacture of HD DVD, DVD and CD discs, Toshiba cannot assure that this player will successfully play every disc bearing the HD DVD, DVD or CD logos. If you happen to experience any dif???culty playing an HD DVD, DVD or CD disc on this player, please contact Toshiba Customer Service.

Some differences

The HD DVD player operates more like a computer and differently than a standard DVD player, In addition to containing a microprocessor, it contains an operating system, random access memory (RAM), and an HD DVD drive. The operating system includes software that is transferred to the RAM when the machine is turned on and at other times during operation. This transfer can take time. Therefore, when you turn the HD DVD player on, it may take a little while before it is ready to use. Likewise, other functions may not be performed as quickly as they would on other AV equipment. Please take these factors into consideration as you use the HD DVD player.

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass.

In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

/PTICALIPICK UP

LENS

Moisture condensation occurs during the following cases.

7When you bring the unit directly from a cold place to a warm place.

7When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.

7In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room.

7When you use the unit in a humid place.

)TS TOO WARM

Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Connect the power cord

of the unit to the wall outlet, turn on the unit, remove the disc, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Notes on copyright

7The unauthorized recording, use, display, distribution, or revision of television programs, videotapes, HD DVDs, DVDs, CDs and other materials, is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and/or criminal liability.

7This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No's. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S. and world-wide patents issued and pending. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc.

HDMI, the HDMI logo and High-De???nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

SHARC is a registered trademark and Melody is a trademark of Analog Devices, Inc.

and are trademarks of DVD Format/Logo Licensing Corporation.

All other brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Connections Introduction

Chapter1Introduction

Features

Playback of HD DVD video discs

HD DVD video discs are high-density, high-capacity discs.

7The HD DVD disc standard has been approved by the DVD forum.

7HD DVD (single layer): 15 GB

HD DVD (dual layer): Maximum capacity of 30 GB A single layer single sided disc (15 GB) has capacity of about 8 hours in 1125 line high de???nition picture; about 48 hours in 525 line standard de???nition picture (depending on bitrate of pre- recorded contents).

*1GB means 1,000,000,000 bytes.

7HD DVD Twin Format Discs have both HD DVD and DVD layers on one side. HD DVD Combination DVD Discs have HD DVD material on one side and standard DVD material on the other side. Because both disc types are new, such discs may not operate properly in this player.

7To view high-de???nition picture in HD DVD discs, an HDTV display (720p, 1080i) is required.

7Connect an HDTV set to the COMPONENT OUTPUT jacks or the HDMI OUTPUT jack on this player.

7Some discs may require use of HDMI OUTPUT for viewing of high resolution material.

Compatible with multiple disc types

7Playback of commercial HD DVD video disc, DVD video, and Audio CD

7Playback of DVD-RW (disc recorded in DVD VR mode or DVD video mode), and DVD-R

7Playback of CD-RW and CD-R (Audio CD of CD-DA format only; playback of MP3, WMA and other non-CD-DA audio formats are not supported.)

Because HD DVD is a new format, disc compatibility issues with new and existing format discs are possible. Not all discs are compatible. If you experience compatibility problems, please contact Toshiba Customer Service.

Blu-ray Discs cannot be played on this player.

Internet connection feature (LAN port)

7Some HD DVD discs enable you to access special HD DVD sites. If an HD DVD site includes content such as movie trailers, you can watch the content on the player via the Internet if your internet connection provides suf???cient bandwidth.

HD output jacks

7An HDMI jack for connecting a single cable to output video and audio signals

7Component jacks

Compatibility notes

7For compatibility, see page 28.

Certain system requirements and limitations

For high de???nition video playback:

7HD display (some discs may require HDCP capable input)

7HD DVD disc with HD content

For Dolby?? Digital Plus and Dolby TrueHD multi-channel audio playback:

7A/V Receiver with HDMI??? multi-channel LPCM capable audio input and 5.1 channel speaker setup.

Certain limitations:

Viewing high-de???nition content and up-converting DVD content may require an HDCP capable input on your display device. Because HD DVD is a new format, certain disc, digital connection and other compatibility issues are possible. Some recordable media may not be supported. Dolby Digital Plus, Dolby TrueHD and DTS support for up to 5.1 channels. DTS-HD support for DTS core only. MP3/WMA audio ???les not supported. Please see www.toshibahddvd.com for more information. Features subject to change and delayed availability. The ???rmware in this player can be updated.

Chapter1Introduction

Index to parts and controls (Continued)

Status indicator

: Playing

II : Pausing

: Fast forward playback : Fast reverse playback

Disc indicator

HD DVD : Illuminates when an HD DVD disc is loaded.

DVD : Illuminates when a DVD disc is loaded.

TITLE indicator

Illuminates when a title number is displayed.

ADV (Advanced) indicator

Illuminates when advanced content is played.

CHP (Chapter) indicator

Illuminates when a chapter number is displayed.

CD indicator

Illuminates when a CD is loaded.

TRK (Track) indicator

Illuminates when a track number is displayed.

Sound format indicator

: Illuminates when Dolby Digital sound is played.

: IIluminates when DTS sound is played.

HDMI Indicator

Illuminates when HDMI connection is veri???ed between the player and another device.

Switching the display

TOTAL indicator

Illuminates when the total playing time of the disc is displayed.

REMAIN (Remaining) indicator

Illuminates when a remaining playback time is displayed.

2ch indicator

Illuminates when 2 channel (L/R) sound is output.

MULTI indicator

Illuminates when 5.1 channel sound is output.

Repeat mode indicator

Illuminates when playing in repeat mode.

Angle icon indicator

Illuminates when playing a scene recorded with multi angles.

16Multi display

Displays the total playing time of the disc, elapsed time, remaining time, title number, chapter number or message, etc.

Video output format indicator

Displays the video output format currently selected.

480 : 480 interlace

480 : 480 progressive

720 : 720 progressive

1080 : 1080 interlace

Every time you press DISPLAY button on the remote control, the display changes the contents. The display may not change, depending on the disc conditions.

Dimming the display

Pressing DIMMER button on the remote control changes the brightness of the display.

??????>?? ??????i` "vv

??? Turning off the power resets this setting.

Chapter1Introduction

Preparation of the remote control

Set up the remote control to operate the player and your TV.

Loading batteries

1 Open the cover.

2 Insert batteries.

7Use 2 batteries (AAA sizes).

7Make sure to match the + and ??? on the batteries to the marks inside the battery compartment.

3 Close the cover.

Notes

Operating with the remote control

Point the remote control at the remote sensor and press the buttons.

Distance: About 7 m (23 ft) from the front of the remote sensor

Angle : About 30?? in each direction of the front of the remote sensor

Do not drop or give the remote control a shock.

Do not leave the remote control near an extremely hot or humid place.

Do not spill water or put anything wet on the remote control.

Do not disassemble the remote control.

Dispose of batteries in a designated disposal area.

Batteries should always be disposed of with the environment in mind.

Always dispose of batteries in accordance with applicable laws and regulations.

If the remote control does not operate correctly, or if the operating range becomes reduced, replace all batteries with new ones.

When necessary to replace batteries in the remote control, always replace all batteries with new ones. Never mix battery types or use new and used batteries in combination.

Be sure to use AAA size batteries.

Always remove batteries from remote control if they are dead or if the remote control is not be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Caution

Never throw batteries into a ???re.

Chapter2Connections

Connecting to a TV

Step1 Check the type of video input on your TV.

To view 480p, 720p or 1080i output, use the HDMI OUTPUT jack or the COMPONENT OUTPUT jacks to connect to a TV. Some discs may require use of the HDMI OUTPUT jack for viewing of high resolution material.

HDMI input

Viewable.21

HDMI INPUT

Most recommended*

*Why HDMI connection is most recommended?

HD DVD and DVD video disc creators have the option to include copy protection instructions in their discs that prohibit the output of some standard video or high de???nition video (original 720p or 1080i or up-converted 480i or 480p) from the COMPONENT OUTPUT jacks. If such instructions are present in the disc you are playing, you must use the HDMI OUTPUT jack to view the disc in a high de???nition format and the COMPONENT OUTPUT jacks, if activated, will output video only in 480i or 480p resolution.

Caution on connection

???Do not power this player using any power cord other than the one supplied with this player.

???Do not use the supplied power cord with any device other than this player.

Notes on connection

???When you connect the player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections.

???Connect the player directly to your TV. If you connect the player to a VCR, TV/VCR combination, video selector or AV ampli???er, the playback picture may be distorted due to copy protection.

Chapter2Connections

Step2 Connect the player to your TV.

Introduction

Via HDMI input

HDMI stands for High De???nition Multimedia Interface. HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables don???t need to be connected separately to a device.

Connections

HDMI INPUT

Depending on the equipment connected to this player, such as a TV or a projector, no sound may be output by the display.

In this case, set ???Digital Output HDMI??? ( page 53) to ???PCM???.

If sound still is not heard, use analog output.

To HDMI OUTPUT

HDMI, the HDMI logo and High-De???nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may restrict output of video on the component video ports when viewing high de???nition content or up-converted DVD content. The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus, because the HDMI output can change automatically to match the maximum available resolution of your display, if you connect both the HDMI output and component output, the resolution on the component output will change if the HDMI output Auto-adjusts.

After completing the connection, proceed to page 23 to make the setting.

Notes

???Refer to the owner???s manual for the TV to be connected to this player for more information concerning HDMI connections.

???When the HDMI connection is not veri???ed, an error message appears on the front panel display. In this case, disconnect the HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

???HDMI output is digital only, DVI analog is not supported.

???HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

???To get the most possible bene???t from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using either its HDMI audio capable input. If your AV receiver has this type of input(s), make sure one of them is connected to your HD DVD player and that the input is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input, but it can decode DTS, then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver. While this connection does not have enough bandwidth to transport the full, high-quality Dolby Digital Plus signal, it will support DTS ??? the highest bandwidth commonly available encoding method that does work over SPDIF. If your receiver does not support DTS, you may be able to obtain a two channel digital by setting the player to output PCM. If your receiver does not have either HDMI or an optical digital input, use the two channel analog outputs.

???If you use the SPDIF optical output or analog outputs to connect your audio system and have the ???Digital Output

HDMI??? ( page 53) set to ???Auto??? or ???PCM???, the audio output level from these jacks will be reduced when listening to a multi-channel disc. To restore the audio output level, set ???Digital Output HDMI??? to ???Downmixed PCM???.

Others

Chapter2Connections

Connecting to an TV (Continued)

Via component video input

Composite video cables (not supplied)

To COMPONENT OUTPUT

To use the optical digital output, use an optical cable to connect this jack to an optical audio input on a device capable of processing a DTS bistream or PCM audio.

To use the analog sound output, connect these jacks to audio input jacks on your TV using the audio cable. For digital sound output, see ???Connecting to an audio system??? ( page 24).

Finally connect the supplied power cord to a wall outlet.

After completing the connection, proceed to page 23 to make the setting.

Via S-VIDEO or VIDEO (yellow) input

Connect either.

*To VIDEO To S-VIDEO

Audio/video cable (supplied)

* To use the optical digital output, use an optical cable to connect this jack to an optical audio input on a device capable of processing a DTS bistream or PCM audio.

Finally connect the supplied power cord to a wall outlet.

480i output only regardless of the resolution settings or the connections of other output jack.

After completing the connection, proceed to page 23 to make the setting.

Chapter2Connections

Step3 Con???gure settings for your display.

Setting of video output resolution of this player

Connections Introduction

1Turn on the TV and select the input to which the player is connected.

2Press ON/STANDBY to turn on the player ( page 30).

3Press SETUP to display ???SETUP MENU???, if not displayed.

SETUP MENU

Picture

ON/STANDBY

Language

Enhanced Black Level

Picture Mode

General

4Press / to select ???Picture??? then press OK.

5Press / to select ???Resolution Setting???, then press OK.

6Press / to select the resolution according to the performance of your TV as shown in the table below.

SETUP

S-VIDEO or

VIDEO (yellow) input

No need to set.

???You may ???nd that setting the output resolution of the player to match as closely as possible the native resolution of your display provides the best picture performance (e.g., 720p for 720p and 1080i for 1080i or 1080p).

7Press OK.

8Press SETUP to turn off ???SETUP MENU???.

Chapter2Connections

Connecting to an audio system

You can enjoy the bene???ts of Dolby Digital Plus or Dolby TrueHD by connecting the HDMI output of your player to an AV receiver with an HDMI audio input. You can listen to down-converted Dolby Digital Plus and Dolby TrueHD as well as Dolby Digital and DTS using a receiver with Dolby Digital and DTS decoding capabilities and an optical digital input.

Via HDMI output

HDMI compatible device

HDMI input

You may need to adjust the HDMI audio output to match the capabilities of your AV amplifier. In this case, set ???Digital Output HDMI??? ( page 53) to ???PCM???.

??? Set ???Digital Output HDMI???

( page 53).

AV amplifier

Caution

When you are connecting (via the HDMI OUTPUT jack) an AV decoder that does not have Dolby Digital or DTS decoding capability, be sure to set ???Digital Output HDMI??? ( page 53) to ???PCM??? or ???Downmixed PCM???. Otherwise, high volume sound may damage your hearing as well as the speakers.

Via optical digital audio output

Caution

When you are connecting (via the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack) an AV decoder that does not have Dolby Digital, DTS or MPEG decoding capability, be sure to set ???Digital Output SPDIF??? ( page 53) to ???PCM???. Otherwise, high volume sound may damage your hearing as well as the speakers.

Note about audio capabilities

Dolby Digital Plus and DTS-HD (DTS core only) capability limited to 5.1 channels.

DTS-HD processing of DTS core only. Full DTS-HD is not supported.

Compatibility notes

7Because HD DVD is a new format, certain disc, digital connection and other compatibility issues are possible. If you experience compatibility problems, please contact Toshiba Customer Service.

7Viewing high-de??? nition content and up-converting standard DVD content may require an HDMI- capable input or HDCP-capable DVI input on your display device.

7Some HD DVD discs and DVD discs may restrict the use of some operation commands or features.

7Dolby Digital Plus, Dolby TrueHD and DTS-HD (DTS core only) capability limited to 5.1 channels.

7DTS-HD processing of DTS core only. Full DTS-HD is not supported.

7Some DVD-R/DVD-RW and CD-R/CD-RW discs may be incompatible due to laser pick-up and disc design.

7CD-R/CD-RW discs must be recorded using CD-DA method for CD audio playback.

7The included remote control may not operate some or all features of your TV or monitor, so it may be necessary to use your original remote control.

7Certain features are subject to delayed availability.

7This product includes memory that is used to store some disc related information, including downloaded on-line content. The disc you are using will control how long this information is retained.

Note

The ??? rmware in this player can be updated. See page 58 for details.

Introduction

spray for vinyl LPs. It may damage the disc.

??? Refer to the instructions of the disc as well.

On storing discs

???Do not store discs in a place subject to direct sunlight or near heat sources.

???Do not store discs in places subject to moisture and dust such as a bathroom or near a humidi??? er.

???Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

???Refer to the instructions of the disc as well.

Chapter3Playback (Basic)

Powering on/Loading a disc

Turning the power on

Press (front panel) or (remote control).

ON/STANDBY indicator ON/STANDBY button

ON/STANDBY button

When the power turns on, ON/STANDBY indicator on the front panel changes color from red (standby mode) to blue (operation).

Start up (and disc loading (see below)) may take time.

Turning the power off

1 Press ON/STANDBY.

The power turns off and ON/STANDBY indicator on the front panel turns red (standby mode).

When you power on this player for the ???rst time, the setting screen will appear. Please refer

to page 50 and select ???General??? > ???Clock Set???. Check the date and time are set properly and correct them if necessary. When complete, press SETUP to exit. Your player is ready.

Note

If the player freezes for about 15 minutes or more and will not respond to any buttons, holding down ON/STANDBY button on the front panel for about 10 seconds can force the player to turn off. However, this is an emergency measure, which may cause damage to the player. Avoid casual use of this measure.

Loading a disc

Press (front panel) or (remote control).

The player opens the disc tray.

Place a disc in the hollow of the disc tray with the playback side down.

When using a double-sided disc, turn the label of the playing side up.

Notes

Use the button on the front panel or the remote control to open and close the disc tray. Do not push or hold the disc tray while it is moving. Doing so may cause the player to malfunction.

Do not load a disc which is unplayable, or any object other than a playable disc.

Do not apply downforce to the disc tray. Doing so may cause the player to malfunction.

If the disc tray stops while closing, the mechanical protection system of this player will open it. Do not force it to close. Doing so may damage the disc tray. If the disc tray will not open, turn the player off, and press OPEN/CLOSE on the front panel. This may turn the player on and open the disc tray. If it still won???t open, contact TOSHIBA Customer Support.

After placing a disc, press OPEN/CLOSE.

Chapter3Playback (Basic)

Playing a disc (Continued)

Playing from the top menu

HD DVD DVD-Video

Some discs may include a top menu, on which you can view the structure of contents or select a scene.

1 Press .

A top menu appears.

Playback starts from chapter 1 of the selected title.

Notes

The instructions above describe basic procedures which may vary depending on the contents of a disc. If different instructions appear on the TV screen, follow those instructions.

If you display the top menu during playback and press TOP MENU button again without selecting any title, the player may resume playback from the point where you ??? rst pressed TOP MENU button (depending on the actual disc.)

This method of locating a title is available only on a disc that contains a top menu.

Instruction notes of discs may refer to the button that displays the top menu as TITLE button.

Depending on a disc, MENU button may have to be pressed instead of TOP MENU button to display the top menu.

Using A/B/C/D buttons

Use these buttons as indicated by the video display during HD DVD disc playback. Depending on the disc contents, the functions of each button may differ.

Playing from a menu in a recorded disc

DVD-RW DVD-R

Discs recorded on personal devices such as DVD recorders may contain menus, on which items can be easily selected.

1 Press .

Recorded contents are displayed.

2 Press /// to select the item you want.

Press .

Playback of the selected item starts.

Notes

Disc menus vary depending on the disc or the recording device. Some discs may not contain a disc menu.

Discs recorded in DVD VR mode display the recorded contents not in thumbnails but in a list. Select an item on the list and press OK button.

Selecting the sound

HD DVD DVD-Video DVD-RW DVD-R

If a disc contains several languages, you can select a preferred language from them to hear.

Connections Introduction

Start

During playback, press .

Language code ( page 59)

Press while the audio setting is displayed

on the TV screen.

Notes

Some discs allow you to change audio selections only via the disc menu. If this is the case, press MENU button and choose the appropriate language from the selections on the disc menu.

When you turn on the player or replace a disc, the player returns to the initial default setting ( page 54). Depending on a disc, a speci??? c type of audio the disc has is output.

Selecting the sound of a disc recorded in DVD VR mode

DVD-RW DVD-R (DVD VR mode)

When playing a disc recorded in DVD VR mode, select the sound as follows.

1 During playback, press .

???The current audio setting appears.

???The language code appears instead of the language name. Refer to the list of languages and their abbreviations. ( page 59)

Depending on the disc or the type of broadcast, variation of sound differs.

???DVD-RW DVD-R

Stereo sound contents

"Stereo" or "LR" (Left main channel and right sub channel) . "L" (Left main channel) . "R" (Right sub channel) . Back to "Stereo" or "LR".

SAP sound contents

"Main" . "Sub" . "Main and Sub" . Back to "Main".

Chapter3Playback (Basic)

Playing a disc (Continued)

Selecting subtitles

HD DVD DVD-Video

You can display subtitles on the TV and select a subtitle language from those included on the disc.

Start

Press during playback.

The current subtitle setting appears.

Language code ( page 59)

Each time you press /, ???On??? and ???Off??? alternate. Select ???On??? to view subtitles.

Press while the subtitle setting is displayed on the TV screen.

Subtitle languages which do not appear in the setting are not included in the disc.

Notes

Some discs are set to display subtitles automatically.

Depending on the scene, subtitles may not appear immediately after you set the subtitle function to on.

Some discs will allow you to change subtitle languages and turn subtitles on or off only via the disc menu.

When you turn on the player or replace a disc, the player returns to the initial default setting ( page 54). Depending on a disc, a speci??? c type of subtitles the disc has is output.

Depending on the scene, the subtitle language may not change immediately after selected.

Selecting the camera angle

HD DVD DVD-Video

If the scene was recorded with multiple angles, you can easily change the camera angle of the scene you are watching.

Notes

Press while playing a scene recorded with

While the angle number is displayed, press repeatedly to select the angle number.

You can also change the camera angle during still playback. The camera angle changes to the new setting when you resume normal playback.

If you pause a picture immediately after changing a camera angle, the resumed playback picture may not display the new camera angle.

Chapter3Playback (Basic)

Playing at various speeds

HD DVD DVD-Video DVD-RW

Introduction

DVD-R CD

CD-RW

(CD-DA)

CD-R

(CD-DA)

Playback starts from the beginning of the current chapter or track. When you press twice, playback starts from the beginning of the previous chapter or track.

Playing frame by frame

During playback, press .

Picture pauses.

If you press while a picture is paused, you can play the picture frame by frame.

???To resume normal playback, press

Some discs may not permit this operation.

Playing in fast reverse or fast forward

During normal playback, press / .

: Fast reverse playback : Fast forward playback

???Each time you press the button, the playback speed changes.

???To resume normal playback, press

Connections

Skipping chapters or tracks

Playback starts from the beginning of the next chapter or track.

Playing in slow-motion

Press during playback.

Picture is played forward in slow- motion.

Page 36 ??? Each time you press the button, the slow-motion speed changes.

??? To resume normal playback, press

??? Not available in CD playback.

Chapter3Playback (Basic)

Playing at various speeds (Continued)

Normally titles, chapters, and tracks are numbered. By entering these numbers, you can access a desired section.

1 Press repeatedly to select the area you want to input.

e.g.

??? The actual display may vary depending on the disc.

The cursor shifts also by / .

2 Press the number buttons to enter a number of the section.

e.g. To enter chapter/track 25:

Press , then press .

???Pressing CLEAR resets the numbers. To turn off the display, press T.SEARCH several times (depending on the disc).

Press .

You may have to press repeatedly, depending on a disc. Press the button until the cursor moves to "-- -- --" area.

e.g.

Search: Title 3 Chapter ??? ??? ??? ??? Time ??? ??? ??? ??? ??? ???

Press the number buttons to enter the desired time location on the disc.

e.g. To enter 1 hour, 25 minutes, and 30 seconds

. . . .

??? Pressing CLEAR resets the numbers.

Press .

Playback starts from the speci??? ed location.

Playback starts from the selected section.

Notes

Some discs may not permit these operations.

While the ADV indicator on the front panel illuminates, these features are not available.

Resuming playback from the location last stopped (Title resume)

Stop

You can resume playback from the location last stopped.

If you press after stopping playback, playback starts from the location last stopped.

If you press after stopping playback, the resume feature is canceled.

Notes

Resume feature cannot function when:

???you select a disc menu language ( page 54) or change the parental lock setting ( page 56).

???you open the disc tray.

There may be a difference in the location where playback resumes depending on the disc.

It is possible to change the setting from the setup menu while the player retains a location in memory, however, the new setting can be valid only after the player clears the location memory, i.e., starts resume playback.

Some discs or scenes may not permit this operation. While the ADV indicator on the front panel illuminates, this feature is not available.

Chapter5Internet connection

Internet connection feature (Outline)

You may use the internet connection feature to update the player???s ???rmware. See page 58.

Future HD DVD discs may enable you to access special HD DVD sites, if you connect the player to the Internet via an always-on broadband connection. For example, if an HD DVD site includes content such as links to future movie trailers, you can watch the content on the player via the Internet.

You do not need to connect to a PC to use this function.

Before using

Before using this feature, please read and understand the important information in ???Notes???.

This feature requires an always-on broadband internet connection.

An HD DVD disc compatible with this feature is required. Not all HD DVD discs are compatible.

Connection requirement

Always-on broadband internet connection.

Notes

Toshiba is not responsible for any malfunction of the player and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment.

Toshiba is not responsible for any trouble in your internet connection.

If you wish to use a wireless network to connect the player, you will need to use a wireless LAN ethernet adapter to connect the player to the network.

The features of HD DVD discs made available through the Internet Connection feature are not created or provided by Toshiba, and Toshiba is not responsible for their functionality or continued availability. Some disc related material available by the Internet Connection may not be compatible with this player. If you have questions about such content, please contact the producer of the disc.

Some internet contents may require a higher bandwidth connection.

Internet connection setting procedure (Outline)

1st DHCP setting

???Set ???DHCP??? to ???On???.

The network information is automatically set.

???Set ???DNS??? to ???On???.

The DNS server is obtained automatically from the DHCP server.

If a connection cannot be established even if ???DHCP??? is set to ???On???.

???Set ???DHCP??? to ???Off???.

Set ???IP Address???, ???Subnet Mask???, and ???Gateway??? manually.

???Set ???DNS??? to ???Off???.

Set the DNS server address manually.

2nd Proxy setting

If the provider you are using requires a proxy setting to be con??? gured, set the corresponding proxy server address.

3rd NTP Server setting

The player automatically accesses an internet server to adjust its clock via the network time protocol.

4th Network Speed setting

Select the speed according to the speci??? cation of your LAN.

5th

Cookie setting

Select whether you accept ???cookies??? or not.

1st DHCP setting

1Press SETUP button. ???SETUP MENU??? appears.

2Press / buttons to select ???Ethernet???, then press OK button.

3On ???Ethernet??? menu, press / buttons to select ???DHCP??? then press OK button.

4Set ???DHCP??? to ???On???, then press OK button.

5 Set ???DNS??? to ???On???, then press OK button.

6Select ???Con??? rm???, then press OK button. Con??? rming starts.

If the setup is successful, an IP address appears. Press OK button.

If the setup is not successful:

a)Set ???DHCP??? to ???Off??? then press OK button.

b)Input the addresses into ???IP Address???, ???Subnet Mask??? and ???Gateway??? using the number buttons.

c)Set ???DNS??? to ???Off??? then press OK button.

d)Input the address into ???DNS Server???.

This sets the DNS server to be used by the player. e.g.: 192.168.1.1

e)Press OK button.

Connections Introduction

Chapter5Internet connection

Internet connection feature (Preparation) (Continued)

2nd Proxy Setting

Enter the proxy server address when your provider requires proxy setting.

1 On ???Ethernet??? menu, press / buttons to select ???Proxy setting??? then press OK button.

2 Set ???Proxy??? to ???On??? then press OK button.

Proxy Setting

Password: Enter the speci??? ed data from the provider.

4 Select ???OK??? then press OK button.

3rd NTP Server setting (Clock adjustment setting)

1On ???Ethernet??? menu, press / buttons to select ???NTP Server??? then press OK button.

2Select ???On??? or ???Off??? by pressing / buttons.

3 Select ???OK??? then press OK button.

4th Network Speed setting

Select your network speed.

1On ???Ethernet??? menu, press / buttons to select ???Network Speed??? then press OK button.

2Select the speed by pressing / buttons.

3Select ???OK??? then press OK button.

5th Cookie Setting

Select whether you wish to accept ???cookies??? or not.

1On ???Ethernet??? menu, press / buttons to select ???Cookie Setting??? then press OK button.

2Select ???Accept??? or ???Not Accept??? by pressing / buttons.

3 Select ???OK??? then press OK button.

Note

If you select to accept ???cookies???, the HD DVD internet services you use may record or track information about your use of the player and/or those sites. If you do not choose to allow cookies, some or all features of a site may not properly function.

User information setting

Although not directly related to the Internet connection, some HD DVD discs may require the following settings to be con??? gured.

1On ???Ethernet??? menu, press/buttons to select ???User Information??? then press OK button.

User information

User

Password ************

OK Cancel

2Select ???User??? then press OK button.

3Input characters by pressing/buttons. To shift the position, press/buttons. Press OK button.

4Select ???Password??? then press OK button.

Input your password in the same manner as step 3. Press OK button.

5Select ???OK??? then press OK button.

???Use a password that others cannot easily guess.

???Do not use the same password you use for other services.

Mac Address

Displays the MAC address of the player.

It cannot be changed.

1On ???Ethernet??? menu, press/buttons to select ???Mac Address??? then press OK button.

The MAC address appears.

Notes

Please contact the router manufacturer when the router DHCP feature is not operating properly (in such a case, an error will occur since the default gateway and the DNS server IP address cannot be obtained).

The ??? rmware in this player is updateable. Seepage 58 for information.

Some applications may require additional bandwidth.

Chapter6Others

Customizing the function settings (Continued)

Picture

TV Shape

16:9

Select when a 16:9 wide TV is connected.

4:3

Select when a standard 4:3 TV is connected.

Displays pictures cropped to ??? ll your TV screen. Both of the picture???s sides are cut off.

4:3 Letter Box

Select when a standard 4:3 TV is connected.

Displays theatrical images with masking bars above and below the picture.

Notes

When an HD DVD disc or a DVD video disc has a particular available picture shape, the contents may not be compatible with other picture shapes.

DVD video discs containing 4:3 picture only always display 4:3 pictures regardless of this setting.

If ???16:9??? is selected while connecting a 4:3 TV, playback pictures may be distorted horizontally or shrink vertically. Make this setting according to your TV shape.

Actual picture shape may depend on signal types of broadcasts or input sources, or settings on the connected TV. Refer to the owner???s manual of your TV.

Enhanced Black Level

You can adjust the black level of the output signal.

To display deeper, richer black than in ???Off??? setting. (0 IRE)

Off

Normal black level. (7.5 IRE)

Video

The player ??? lters video signal, and converts it in the progressive output format appropriately. Suitable for playback of video content pictures.

Auto

Select this position normally. The player automatically detects source content, ??? lm or video, of playback source, and converts that signal in the progressive output format in an appropriate method.

Note

The player may not be able to detect the source (???lm or video) of some material. If you notice undesirable picture performance, try selecting ???Film??? or ???Video???.

Resolution Setting

Seepage 23.

Picture Mode

There are two types of source content in pictures recorded in DVD video discs: ??? lm content (pictures recorded from ??? lms at 24 frames per second) and video content (video signals recorded at 30 frames per second). Make this selection according to the type of content being viewed.

Film

The player converts ??? lm content pictures in the progressive output format appropriately. Suitable for playback of ??? lm content pictures.

Audio

Connections Introduction

For details about output sound selection, see page 60.

Bitstream

Select this when an AV receiver or processor equipped with built-in Dolby Digital, DTS or MPEG decoder is connected to this player.

When you play a disc recorded in Dolby Digital or DTS format, digital audio signal (bitstream audio) is output. When you play a disc recorded in Dolby Digital Plus, Dolby TrueHD or DTS-HD, the sound is converted to a DTS bitstream. If the AV receiver or processor does not support DTS, select "PCM".

PCM

Select this when a 2 channel digital stereo ampli??? er is

connected to this player.

When you play an HD DVD or DVD video disc recorded in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD format, sound is converted into PCM (2 channel) format.

Digital Output HDMI

Select the output sound format when a device equipped with an HDMI terminal is connected to the HDMI OUTPUT jack on this player.

For details about output sound selection, see page 60.

Auto

Select this when an HDMI device equipped with built-in Dolby Digital, DTS, MPEG or linear PCM decoder is connected to this player.

When you play a disc recorded in Dolby Digital Plus, Dolby TrueHD or DTS-HD, PCM is output (core only for DTS-HD).

When you play a disc recorded in Dolby Digital or DTS format, digital audio signal (bitstream audio) is output.

If a connected HDMI device does not support Dolby Digital, DTS or MPEG, sound is converted into linear PCM to output.

PCM

Select this when an HDMI device which has multi channel input is connected to this player.

When you play an HD DVD or DVD video disc recorded in multi channel in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD format, the sound is decoded and output in multi channel in linear PCM format.

Downmixed PCM

Select this when a 2 channel digital stereo AV receiver or

processor is connected to this player.

Note

Setting ???Auto??? or ???PCM??? will reduce output level of multi channel sound from the ANALOG AUDIO OUTPUT jacks and the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack if you:

???view the playback picture on an HDMI TV connected to this player.

???play an HD DVD video disc of a certain type, recorded in

linear PCM format.

In this case,the output level will be restored by setting to ???Downmixed PCM???.

Dynamic Range Control

To turn on or off a function that makes faint sounds easier to hear even if you lower the volume during late-hour playback.

Auto

While playing an HD DVD video disc recorded in Dolby TrueHD format, this function will be automatically activated or disabled according to certain command included in the content.

For other discs, this function is activated.

This function is activated.

Off

This function is disabled.

Notes

This function is effective only in playback of HD DVD or DVD video discs recorded in Dolby Digital, Dolby Digital Plus or Dolby TrueHD format.

The effect level of this function vary depending on the disc.

Dialog Enhancement

To turn on or off a function that increases dialog volume of a DVD video disc playback.

This function is activated.

Off

This function is disabled.

Notes

This function is effective only in playback of Dolby Digital recorded HD DVD or DVD video discs.

The effect level of this function vary depending on the disc.

Chapter6Others

Customizing the function settings (Continued)

Language

Disc Menu Language

To select a preferred language for disc menus.

English

To display disc menus in English.

French

To display disc menus in French.

Japanese

To display disc menus in Japanese.

German

To display disc menus in German.

Others

To make a further language choice.

After pressing OK button, follow steps 1) ??? 4) below.

1)Obtain the language code of the preferred language from the Language code list ( page 59).

Note

Some discs may be played in a different language from that you selected, as the disc may contain alternate language.

Subtitle Language

To select a preferred language for subtitles.

None

To disable subtitles.

English

To display subtitles in English.

French

To display subtitles in French.

Japanese

To display subtitles in Japanese.

German

To display subtitles in German.

Others

To make a further language choice.

After pressing OK button, follow steps 1) ??? 4) below.

1)Obtain the language code of the preferred language from the Language code list ( page 59).

Notes

Some discs may be set to display subtitles in a different language from that you selected, as the disc may contain alternate language.

Some discs allow you to change subtitle selections only via the disc menu. In this case, press MENU button and choose the appropriate subtitle language from the selection on the disc menu.

Audio Language

To select a preferred language for the sound track.

English

To display sound tracks recorded in English.

French

To display sound tracks recorded in French.

Japanese

To display sound tracks recorded in Japanese.

German

To display sound tracks recorded in German.

Others

To make a further language choice.

After pressing OK button, follow steps 1) ??? 4) below.

1)Obtain the language code of the preferred language from the Language code list ( page 59).

Note

Some discs may be played in a different language from that you selected, as the disc may contain alternate language.

Chapter6Others

Customizing the function settings (Continued)

General

Parental Lock

HD DVD and DVD video discs equipped with the Parental Lock function have a predetermined limitation level. The limitation level or limitation method may differ depending on the disc. For example the whole contents of a disc may not be played back, or an extreme violent scene may be cut or replaced automatically by another scene.

Important

Depending on discs, it may not be evident whether the disc is compatible with Parental Lock function. Make sure that Parental Lock function you set is activated correctly.

1Enter a 4-digit password by using the number buttons, then press OK button.

When you use the player for the ??? rst time, set a new password of 4-digit. If you make a mistake entering your password, press CLEAR button before pressing OK button, and re-enter the correct password.

2Set the details.

Parental Lock

a) Select ???On??? or ???Off??? by pressing / buttons.

Select this to activate Parental Lock function or to change the setting.

Off

Deactivate the Parental Lock function.

Skip step 3.

b)Press / buttons to enter the code of a country/ area whose standards were used to rate a disc, referring to the list below.

c)Select the desired limitation level by pressing / buttons.

Unless the Parental Lock function is set to ???Off???, a disc that has a higher limitation level than your selected limitation level cannot be played back. For example, if you select level 7, discs exceeding level 8 are locked and cannot be played back.

When ???US??? is selected, its limitation level corresponds to the following settings.

3 Select ???OK??? then press OK button.

To change the limitation level of Parental Lock function

Follow step 1 - 3 above.

To change the password

1At step 1, press STOP button 4 times then press OK button.

The password is cleared.

2Enter a new 4-digit password by using the number buttons.

3Press OK button.

3Enter the year using the number buttons, then press OK button.

4Set ???Month???, ???Date??? and ???Time??? in the same manner as 3.

The clock starts.

Note

If a power failure occurs or the power cord is disconnected, the clock data will be erased. Reset the clock.

OSD On/Off

To activate or deactivate the operational status display on the TV screen.

Activates the operational status display (e.g., ) on the TV screen.

Off

Deactivates the operational status display (e.g., ) on the TV screen.

Remote Controller Sound

To turn on or off the con??? rmation beeper announcing when each remote command is received.

Turns on the beep sound.

Off

Turns off the beep sound.

Screen Saver

To turn on or off the screen protection function.

Auto Power Off

Turns the player off if picture pausing continues for about 20 minutes.

Activates the screen saver if picture pausing continues for about 20 minutes.

Off

Deactivates the screen saver.

Notes

Toshiba does not guarantee that this function will protect your display.

To close the screen saver, press any button on the player or the remote control.

Connections Introduction

buttons to select ???Yes??? then press OK button.

Chapter6Others

Customizing the function settings (Continued)

General

Maintenance (including internet ???rmware update)

Initialize

To reset all the settings listed on page 53 to factory set default.

Press /

Update (Firmware update)

If you have a broadband internet service you may obtain ??? rmware updates over the internet using the LAN port on the back of your player. ( pages 44 to 46 for information on con??? guring and connecting your LAN port.) Then follow these steps:

Make sure no disc is loaded in the player.

Press SETUP and select Maintenance. Follow the instructions on the screen.

If no update is available, a message will note this and the process will terminate.

If an update is available, the player will download it showing the status of the process on its display.

Do not attempt to roll back to a prior ??? rmware version. This may damage your player.

Caution

Do not unplug, turn off or use any other feature of the player during the download. The writing of the software being downloaded will be halted and the player may no longer work properly. If the player stops working, contact Toshiba Customer Service.

Note

If a broadband connection is not available for use by your player, you may obtain ??? rmware updates by mail. There is a postcard included with this player that you can use to sign up for updates on ??? rmware availability and to automatically receive update discs.

Persistent Storage

To open the menu to control player???s memory allocated for content.

The menu selections will vary depending on the content. Operate following the instructions displayed on your screen.

Twin Format Disc

To select a layer to play, HD DVD or DVD of an HD DVD Twin Format Disc. (Not available while a disc is loaded.)

HD DVD

Only the HD DVD layer is played.

DVD

Only the DVD layer is played.

Note

For combination discs, select the desired version by disc side (see label for information).

Chapter6Others

License information on the software used in theTOSHIBA HD DVD player

This document is statement purpose only. Not concerned with operation of this product.

The software pre-installed in the TOSHIBA HD DVD player consists of multiple, independent software components. Each software component is copyrighted by TOSHIBA or a third party.

The TOSHIBA HD DVD player uses software components that are distributed as freeware under a third-party end-user license agreement or copyright notice (hereinafter referred to as a ???EULA???).

Some EULAs require that the source code of the applicable component be disclosed as the condition for distributing the software component in executable format. You can check the software components subject to such EULA requirements on the following phone number:

Phone number: 1-800-631-3811

TOSHIBA provides a warranty for the TOSHIBA HD DVD player you have purchased under conditions set forth by TOSHIBA.

However, some of the software components distributed under an EULA are made available for use by the user on the assumption that they are not copyrighted or warranted by TOSHIBA or any third party. These software components are licensed to the user free of charge and therefore not covered by any warranty within the scope of the applicable laws. These software components are not subject to any copyrights or other third-party rights and are provided in ???as is??? condition without any warranty, whether express or implied.???Warranty??? here includes, but not limited to, an implied warranty for marketability or ??? tness for speci??? c uses. All risks associated with the quality or performance of these software components are assumed by the user. TOSHIBA shall not be liable whatsoever for any cost of repair or correction or other incidental expense incurred in connection with a defect found in any of these software components. Unless speci??? ed under the applicable laws or in a written agreement, a party who changes or redistributes the software with consent from the copyright holders or based on the aforementioned licenses shall not be held liable whatsoever for any loss arising from the use of or inability to use such software components. The same applies even when the copyright holders or relevant third parties have been informed of the possibility of such loss. ???Loss??? here includes normal, special, incidental and indirect loss (including, but not limited to, the loss of data or its accuracy; loss incurred by the user or any third party; and interface incompatibility with other software). Please read each EULA for details on the use conditions and items that must be observed regarding these software components.

The table below lists the software components pre-installed in the TOSHIBA HD DVD player, which are subject to EULAs. The user should read the applicable EULAs carefully before using these software components. The EULAs are exhibited in their original text (English) as exactly written by the respective parties other than TOSHIBA

Connections Introduction

E x h i b i t A

GNU GENERAL PUBLIC LICENSE Version 2, June 1991

59 Temple Place, Suite 330, Boston, MA 02111-1307

USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software ??? to make sure the software is free for all its users.

This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid

Others

anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modi??? ed by someone else and passed on, we want its recipients to know that what they have is not

the original, so that any problems introduced by others will not re???ect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.

The precise terms and conditions for copying, distribution and modi??? cation follow.

Chapter6Others

License information on the software used in the TOSHIBA HD DVD player (Continued)

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS

FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modi??? cations and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modi??? cation".) Each licensee is addressed as "you".

Activities other than copying, distribution and modi??? cation are not covered by this License;they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the

Program). Whether that is true depends on what the Program does. 1.You may copy and distribute verbatim copies of the Program's

source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an

appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modi??? cations or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a)You must cause the modi??? ed ??? les to carry prominent notices stating that you changed the ??? les and the date of any change.

b)You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this License.

c)If the modi??? ed program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.

(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modi??? ed work as a whole. If identi??? able sections of that work are not derived from the Program,and can be reasonably considered independent and

separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3.You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a)Accompany it with the complete corresponding machine- readable source code,which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b)Accompany it with a written offer, valid for at least three years, to give any thirdparty, for a charge no more than your cost

of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange;or,

c)Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modi??? cations to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface de??? nition ??? les, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4.You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the

Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6.Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7.If as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot

distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all.

For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8.If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9.The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program speci??? es a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10.If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT

PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR

OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF

THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR

AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR

ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR

INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED

TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR

LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE

OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),

EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source ??? le to most effectively convey the exclusion of warranty; and each ??? le should have at least the "copyright" line and a pointer to where the full notice is found.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation,Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright ?? 19yy name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are

welcome to redistribute it under certain conditions; type `show c' for details.

The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items ??? whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program; if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.

<signature of Ty Coon>,1 April 1989 Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License.

Connections Introduction

Chapter6Others

License information on the software used in the TOSHIBA HD DVD player (Continued)

E x h i b i t B

GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999

Copyright ?? 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the ??? rst released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the

version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software ??? to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages ??? typically libraries ??? of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you ???rst think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object ???les to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/ or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modi???ed by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use speci???ed in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination ???ts its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of

an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it

becomes a de-facto standard. Toachieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modi???ed version of the Library.

The precise terms and conditions for copying, distribution and modi???cation follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND

CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0.This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/ or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modi???cations and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modi???cation".)

"Source code" for a work means the preferred form of the work for making modi???cations to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface de???nition ???les, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modi???cation are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1.You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all

the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute

such modi???cations or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a)The modi???ed work must itself be a software library.

b)You must cause the ???les modi???ed to carry prominent notices stating that you changed the ???les and the date of any change.

c)You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d)If a facility in the modi???ed Library refers to a function or a table

of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely wellde???ned independent of the application. Therefore, Subsection 2d requires that any

applicationsupplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modi???ed work as a whole. If identi???able sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3.You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4.You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satis???es the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5.A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a "work that uses the Library" uses material from a header ???le that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not.

Whether this is true is especially signi???cant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely de???ned by law.

If such an object ???le uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object ???le is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6.As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modi???cation of the work for the customer's own use and reverse engineering for debugging such modi???cations.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a)Accompany the work with the complete corresponding machine- readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modi???ed executable containing the modi???ed Library. (It is understood

that the user who changes the contents of de???nitions ???les in the Library will not necessarily be able to recompile the application to use the modi???ed de???nitions.)

b)Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modi???ed version of the library, if the user installs one, as long as the modi???ed version is interface- compatible with the version that the work was made with.

c)Accompany the work with a written offer, valid for at least three years, to give the same user the materials speci???ed in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d)If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above speci???ed materials from the same place.

e)Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing

the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7.You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities

not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library

Connections Introduction

Chapter6Others

License information on the software used in the TOSHIBA HD DVD player (Continued)

and of the other library facilities is otherwise permitted, and provided that you do these two things:

a)Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b)Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to ???nd the accompanying uncombined form of the same work.

8.You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying

or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10.Each time you redistribute the Library (or any work based on the Library???, the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11.If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12.If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library speci???es a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or

of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any

version ever published by the Free Software Foundation.

14.If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is

copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision

will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT

PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/ OR OTHER

PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF

ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS

TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH

YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE

COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR

AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR

ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR

INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED

TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR

LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF

THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN

IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source ???le to most effectively convey the exclusion of warranty; and each ???le should have at least the "copyright" line and a pointer to where the full notice is found.

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation,Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>,1 April 1990 Ty Coon,President of Vice

That's all there is to it!

E x h i b i t C

LICENSE ISSUES

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit.

See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org. OpenSSL License

Copyright ?? 1998-2002 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modi??? cation, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3.All advertising materials mentioning features or use of this software must display the following acknowledgment:

"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

4.The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5.Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

6.Redistributions of any form whatsoever must retain the following acknowledgment:

"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http:// www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"

AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT

OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY

WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com). Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed.

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.

This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modi??? cation, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

3.All advertising materials mentioning features or use of this software must display the following acknowledgement:

"This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)"

The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic related :-).

4. If you include any Windows speci??? c code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:

"This product includes software written by Tim Hudson (tjh@ cryptsoft.com)"

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND

ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.

IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY

WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

Connections Introduction

E x h i b i t D

???This product includes software developed by the OpenSSL project.

???Reverse engineering, disassembling, decompiling, dismantling, or otherwise attempting to analyze or modify the software included in this product is prohibited.

Chapter6Others

Speci???cation

Introduction

Power requirement

33.0W

Power supply

120V AC 60Hz

Mass

4.1kg

External dimension

Width 430 x Height 65.5 x Depth 345mm

Signal system

Standard NTSC Color TV system

Laser

Semiconductor laser, Wavelength: 405nm/650nm/ 780nm

Analog audio output

2.0V (rms), 2.2kor below, pin jack

(L, R) x 1 system

Digital audio output (BITSTREAM/PCM jack)

Optical connector x 1 system

LAN port

100BASE-TX/10BASE-T ?? 1

EXTENSION port

EXTENSION port ?? 2 systems

HDMI output

19 pin

Remote control

Wireless remote control (SE-R0252)

Connections

VIDEO output

Operating conditions

1.0Vp-p (75 ), Sync signal negative,

Temperature: 41??F ~ 95??F (5??C ~ 35??C),

Pin jack x 1 system

Position: Horizontal

S-VIDEO output

Clock accuracy

(Y) 1.0Vp-p (75 ), Sync signal negative,

Quartz (monthly deviation: approximately ??30

Mini DIN4 Pin x 1 system

seconds)

Component output (Y, PB PR)

Y output (green), 1.0Vp-p (75),

Sync signal negative, Pin jack x 1 system

PB, PR output (blue, red), 0.7Vp-p (75),

Pin jack x 1 system each

Designs and speci??? cations are subject to change without notice.

This model may not be compatible with features and/or speci??? cations that may be added in the future.

The Illustrations and screens described in this manual may be exaggerated or simpli??? ed for easy recognition and may be slightly different from the actual unit.

Chapter6Others

Limited Canadian Warranty

For Toshiba Brand HD DVD Players

Toshiba of Canada Limited (???TCL???) makes the following limited warranties to original consumers in Canada. THESE LIMITED

WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS TOSHIBA BRAND HD DVD Player (the ???PLAYER(S)??? or ???Player(s)???) AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER

PURCHASER OR TRANSFEREE.

PLAYERS PURCHASED IN CANADA, AND USED ANYWHERE OUTSIDE OF CANADA INCLUDING, WITHOUT LIMITATION, THE

UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.

PLAYERS PURCHASED ANYWHERE OUTSIDE OF CANADA, INCLUDING, WITHOUT LIMITATION, THE UNITED STATES AND

MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE WARRANTIES.

Limited One (1) Year Warranty on Parts and Labour (home/ non-commercial use)

Subject to the more limited warranty if the Player is used for any commercial or business purposes as set out below, TCL warrants the Player and its parts against material defects in materials or workmanship that result in the Player failing for a period of one

(1) year after the date of original retail purchase. DURING THIS

PERIOD, TCL WILL, AT TCL???S OPTION, REPAIR OR REPLACE

A DEFECTIVE PART WITH A NEW OR REFURBISHED PART,

WITHOUT CHARGE TO YOU FOR PARTS OR LABOUR. THE

ENTIRE PLAYER MUST BE SHIPPED PREPAID TO THE

CLOSEST TOSHIBA FACTORY SERVICE DEPOT IN MARKHAM, MONTREAL OR VANCOUVER (a ???Toshiba Factory Service Depot??? or ???TOSHIBA FACTORY SERVICE

DEPOT???). TRANSPORTATION AND INSURANCE CHARGES

FOR THE PLAYER ARE THE RESPONSIBILITY OF THE

OWNER. THE REPAIRED PLAYER WILL BE RETURNED

PREPAID.

Rental Units

The warranty for Player rental units begins with the date of ??? rst rental or thirty (30) days from the date of shipment to the rental ??? rm, whichever comes ??? rst.

Limited Warranty for Commercial Units

TCL warrants Players that are used for any commercial or business purposes as follows: all parts are warranted against material defects in materials or workmanship that result in the Player failing for a period of ninety (90) days after the date of original retail purchase. DURING THIS PERIOD, TCL WILL, AT

TCL???S OPTION, REPAIR OR REPLACE A DEFECTIVE PART

WITH A NEW OR REFURBISHED PART, WITHOUT CHARGE

TO YOU FOR PARTS OR LABOUR. THE ENTIRE PLAYER

MUST BE SHIPPED PREPAID TO THE CLOSEST TOSHIBA

FACTORY SERVICE DEPOT IN MARKHAM, MONTREAL OR

VANCOUVER. TRANSPORTATION AND INSURANCE

CHARGES FOR THE PLAYER ARE THE RESPONSIBILITY OF

THE OWNER. THE REPAIRED PLAYER WILL BE RETURNED

PREPAID.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE

FOLLOWING CONDITIONS:

1)You must provide your bill of sale or other proof of purchase.

2)All warranty servicing of this Player must be performed by a Toshiba Factory Service Depot.

3)The warranties from TCL are effective only if the Player is (i) purchased as new and unopened from TCL or from TCL???s authorized distributors, dealers or resellers (???ADR???s???) and (ii) located/operated in Canada.

4)Warranties extend only to material defects in materials or workmanship as limited above, and do not extend to:

a.Service, repairs or replacement made necessary by accident, misuse, abuse, moisture, liquids, dust, dirt, neglect, accident, damage, 24/7 applications, improper installation, improper operation, improper cleaning, improper maintenance, normal wear and tear, or any other external cause or event, act or omission outside the control of TCL, including ??? re, theft, acts of God, alteration, power failures, power surges or power shortages, lightning, other electrical faults, or repairs, modi??? cations or replacements by persons other than those authorized by TCL to service the Player;

b.Replacement of missing, discarded or lost parts, the provision of retro??? ts, or preventive maintenance;

c.Repair of damage that is cosmetic only or does not affect the Player functionality, such as wear and tear, scratches and dents;

d.Service on Toshiba-branded accessory items (such accessory items may be covered by their own warranty);

e.Service on third party products or service made necessary by use of incompatible third party products;

f.Service made necessary by the simultaneous use of this Player and connected equipment;

g.Modi??? cations to the Player not approved in writing by TCL, and service made necessary by the use or installation of non-Toshiba modi???cations to the Player;

h.Service of a Player on which the TOSHIBA label or logo, rating label or serial number have been defaced or removed;

i.On-site service and repair of the Player; and

j.Damage to the Player caused by failure to follow the speci??? cations, User manuals or guides as to usage and/or storage.

Disclaimer and Limitation of Remedy

TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER

EXPRESS AND IMPLIED WARRANTIES, CONDITIONS AND

REPRESENTATIONS FOR THIS PLAYER, INCLUDING THE

IMPLIED WARRANTIES AND CONDITIONS OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE HEREBY DISCLAIMED AND EXCLUDED.

IF THE APPLICABLE LAW, STATUTORY OR OTHERWISE,

PRECLUDES THE EXCLUSION OF ANY IMPLIED

WARRANTIES, CONDITIONS AND REPRESENTATIONS

THEN SUCH IMPLIED WARRANTIES, CONDITIONS AND

REPRESENTATIONS ARE OTHERWISE LIMITED IN

DURATION TO THE TERM OF THIS EXPRESS WRITTEN

LIMITED WARRANTY. TO THE EXTENT NOT PRECLUDED

BY LAW, THIS WRITTEN WARRANTY SUPERCEDES AND

SPECIFICALLY DISCLAIMS ANY OTHER WARRANTY,

CONDITION OR REPRESENTATION NOT STATED IN THIS

WARRANTY, WHETHER MADE BY TCL, TOSHIBA CORPORATION, THEIR AFFILIATES, AND ADRs AND

WHETHER MADE ORALLY OR IN WRITING (INCLUDING ANY

STATEMENT IN ANY BROCHURE, PRESS RELEASE,

ANNOUNCEMENT, ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).

YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE

INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR

MANUALS. IF YOU FAIL TO DO SO, THIS PLAYER MAY NOT

FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE.

THIS WARRANTY WILL NOT COVER ANY SERVICE THAT IS

REQUIRED, IN PART OR IN WHOLE, AS A RESULT OF ANY

FAILURE TO FOLLOW THE SET-UP AND USAGE

INSTRUCTIONS. THIS WARRANTY DOES NOT APPLY AND

SHALL BE VOID AND UNENFORCEABLE IF THE PLAYER IS

OPENED, SERVICED, OR REPAIRED BY PERSONS OTHER

THAN THOSE AUTHORIZED BY TCL TO SERVICE OR REPAIR

THE PRODUCT.

IF THE PLAYER FAILS TO WORK AS WARRANTED ABOVE,

YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR

OR REPLACEMENT OF THE DEFECTIVE PART. IN NO EVENT

WILL TCL, TOSHIBA CORPORATION, THEIR AFFILIATES OR ADRs (THE ???RELATED PARTIES???) BE LIABLE TO YOU OR

ANY THIRD PARTY FOR ANY DAMAGES, MONEY,

REIMBURSEMENT, COSTS OR EXPENSES. THIS LIMITATION

APPLIES TO DAMAGES, MONEY, REIMBURSEMENT, COSTS

OR EXPENSES OF ANY KIND WHATSOEVER INCLUDING

ANY DIRECT OR INDIRECT DAMAGES, DAMAGE TO

PROPERTY OR PERSON, LOST PROFITS, LOST SAVINGS,

INCONVENIENCE OR OTHER SPECIAL, INCIDENTAL,

EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER

FOR BREACH OF WARRANTY, BREACH OF CONTRACT,

TORT (INCLUDING NEGLIGENCE), UNDER A STATUTE OR

UNDER ANY OTHER LAW OR FORM OR ACTION, OR

WHETHER ARISING OUT OF THE USE OF OR INABILITY TO

USE THE PLAYER, EVEN IF ANY OF THE RELATED PARTIES

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.

No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever.

Arbitration and Dispute Resolution

To the extent not precluded by law, any claim, dispute, controversy or disagreement (whether for breach of warranty, breach of contract, tort (including negligence), under a statute or under any other law or form of action) against any of the Related Parties arising out of, or otherwise relating to: (i) this warranty; (ii) the Player; (iii) any oral or written representations, statements, brochures, press releases, advertising, announcement, point of sale display, or promotional material relating to the Player; (iv) the relationships that result from this warranty, (the foregoing claims, disputes controversies and disagreements are collectively referred to as the ???Dispute???), shall be referred to and resolved by ??? nal and binding arbitration (to the exclusion of the courts). To the extent not precluded by law, you agree to waive any right that you may have to commence or participate in any representative or class proceeding against the Related Parties relating to any Dispute. If and where applicable and to the extent not precluded by law, you further agree to opt out of any such representative or

class proceedings. Arbitration of any Dispute will be conducted in the forum and in the manner as agreed to between you and TCL. Failing such agreement, the arbitration will be conducted by one arbitrator pursuant to the laws and rules relating to arbitration generally in force in the jurisdiction in which you reside at the time that the Dispute arises. To the extent not precluded by law, no claim, dispute, controversy or disagreement of any other person may be joined or combined with any Dispute by you, without the prior written consent of TCL.

General Provisions

If and to the extent that any provision of this limited warranty should generally be found to be unenforceable, the unenforceable provision shall be severed from the warranty and deemed not to form part of the warranty. The remaining provisions of this warranty shall be and remain valid and enforceable. If and to the extent that any provision of this limited warranty as it relates to any of the Related Parties is found to be invalid or unenforceable in respect of that party (the ???Excluded Party???), the Excluded Party shall be deemed to be severed or excluded from the provision, and the provision shall remain valid, enforceable and applicable in respect of the other or remaining Related Parties.

To the extent permitted by law, this limited warranty shall be governed and construed in accordance with the laws of Ontario.

If there is any inconsistency between this limited warranty, on the one hand, and any statement in the packaging of the Player or in any other document enclosed with, or used in the context of the promotion or sale of, the Player, on the other hand, the provisions of this limited warranty shall prevail.

How to Obtain Warranty Services

If, after following all of the operating instructions in this manual and checking the ???Troubleshooting??? section, you ??? nd that service is needed:

(1)To ??? nd the nearest Toshiba Factory Service Depot, visit TCL???s web site at www.toshiba.ca, or call toll free 1-800-268-3404

(2)Present your bill of sale or other proof of purchase to the Toshiba Factory Service Depot.

For additional information, visit TCL???s website:

www.toshiba.ca

Connections Introduction