How To Set Up and Use Your Wireless Rain Gauge System
1.Follow Battery Installation and Clock/Calendar Set Up as directed above.
2.Place the receiver unit as close as possible to the transmitter and sensor (they must be within 100 feet of each other). This will ensure easy synchronization between the transmission and reception of signals as you set up your wireless system.
3.The receiver unit should display zeros after proper battery installation and registration signal initialization. If the receiver still shows dashes, reinstall the receiver's batteries. If the receiver shows a numerical rainfall value after installing the rain gauge, reset it by pressing the "+" button. See Battery Installation section for detailed instructions.
Note: The effective transmission range of the transmitter and sensor is 100 feet. The effective range is vastly affected by building materials, physical obstructions (trees, sheds, fountains, etc), and where the receiver and transmitter units are positioned. Try various set ups for the best result. Shorten the distance between the receiver and transmitter units when necessary. Keep the transmitter at least 3 feet from any obstructions which may affect rain collection. For instance, do not place the transmitter under a tree, as water dripping from leaves into the rain cup will overstate actual rainfall.
4.The receiver unit is factory set to display total rainfall in inches. To switch measurement to millimeters, press and hold the
5.The receiver unit is factory set to display temperature in Fahrenheit. To switch to Celsius, press and hold the "MAX/MIN" button for 3 seconds. The receiver display will switch to Celsius.
6.The remote sensor is factory set to display temperature in Fahrenheit. To switch to Celsius, press the "??F/??C" button inside the sensor's battery compartment. The remote display will switch to Celsius.
7.To cancel a temperature registration, press and hold the "CH" button for 3 seconds. The temperature reading on the receiver unit will change to dashes. The registration is canceled.
How to Read Rainfall Data
1.Your Taylor?? Wireless Rain Gauge will track the amount of daily, weekly, and monthly rainfall. It will also report total accumulated rainfall, which is the total rainfall recorded since the unit was last reset to zero. Press the
2.A signal is sent from the transmitter to the receiver every 30 seconds when it is raining. If there is no rainfall, a signal will transmit every 2?? minutes. This signal will update the data on the receiver if any changes have occurred.
3.As rainfall occurs, the Daily Rainfall Display will show the amount of rain accumulated throughout the day. When the clock reaches midnight, the display for daily rainfall will automatically reset to zero.
4.For the first day of rainfall, the Daily, Weekly, Monthly, and Total rainfall accumulation will be the same. As additional rainfall occurs throughout the week/month, the unit will add the rainfall amounts together for a weekly/monthly/ total rainfall accumulation.
5.The Weekly rainfall total accumulates from Sunday to Saturday. When the clock reaches 12:00am (midnight) every Sunday, the weekly total rainfall will automatically reset to zero.
6.The Monthly rainfall total accumulates from the first day of the calendar month to the last day. When the clock reaches 12:00am (midnight) on the first day of the month, the monthly total rainfall will automatically reset to zero.
7.Total Rainfall accumulates from the first day the rain gauge is put into use. The receiver will continue to record Total Rainfall until the user clears the memory or the batteries are replaced.
8.To manually reset either the Daily, Weekly, Monthly, or Total Rainfall accumulations, first press the
How to Read Temperature Data
1.The receiver unit shows two temperature readings to the right of the clock/calendar display. The bottom readout is the temperature at the receiver's location. The top readout is the temperature at a remote sensor's location. If more than one remote sensor is set, simply press the ???CH??? button on the back of the receiver to toggle to another channel. The ???CH??? (Channel) Icon will indicate which channel is currently displayed.
2.Press the ???MAX/MIN??? button once to display the highest recorded indoor/outdoor temperatures. Press ???MAX/MIN??? again to display the lowest recorded indoor/outdoor temperatures. Each reading will display for 5 seconds, and then the display will return to the current temperatures.
3.To clear the Min/Max memory, press the ???CLEAR??? button while the maximum/minimum readings are displayed on the LCD.
4.Press and hold the ???MAX/MIN??? button for 3 seconds to switch between ??F and ??C on the receiver display.
Important: Though the rain gauge is
Transmission Collision
Signals from other household devices, such as doorbells, home security systems and entry controls, may temporarily interfere with the rain gauge transmissions. This is normal and does not affect the general performance of this product. The transmission will resume once the interference recedes.
Disconnected Signals
If the receiver unit does not receive a transmission from the transmitter or the remote sensor for 1 hour, the display will show dashes.
To correct this problem:
1.Check that the transmitter and remote sensor are properly positioned, within a 100' transmission range.
2.Check to make sure the transmission path is clear of obstacles and interference.
3.If new batteries are faulty on the initial installation, install fresh batteries, following the steps in the Battery Installation section of
this manual.
4.At temperatures below 32??F (0??C), the LCD readout on the remote sensor may fail to display. When this occurs, the sensor will still transmit correct temperature readings to the receiver unit, but the temperature can not be seen on the sensor. When the temperature rises above 32??F (0??C), the display will begin to function normally again.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Modifications not authorized by the manufacturer may void user's
authority to operate this device.
Precautions
This Digital Wireless transmitter is engineered to give you years of satisfactory service if you handle it carefully, following these guidelines:
1.The receiver is intended for indoor use only. It is not sealed against moisture and could be damaged if used outdoors.
2.Do not immerse the receiver in water. If you spill liquid on it, dry it immediately with a soft,
3.The transmitter is
4.Though the rain gauge is
5.Though the remote temperature sensor is
6.Do not mount the remote sensor on a metal surface.
7.Do not subject the remote sensor to extremely severe temperatures.
8.Do not place into ovens, freezers, or microwaves.
9.Do not clean any of the units with abrasive or corrosive materials. This may scratch plastic parts and corrode electronic circuits.
10.Do not subject any unit to excessive force, shock, dust, temperature or humidity. This may result in malfunction, shorter electronic life span, damaged batteries or distorted parts.
11.This equipment contains no
12.Do not mix old and new batteries. Do not dispose of batteries in fire. Batteries may explode or leak. Remove the batteries if the thermometer will not be used for a long period of time.
13.Always refer to this instruction manual before operating this product.
Specifications
Range of temperature measurement:
Indoor: 32??F to 122??F (0??C to 50??C)
Outdoor:
Using Sensor Probe Cable:
Outdoor:
Range of rainfall measurement:
Daily:
Weekly:
Monthly:
Resolution: 0.04 inches (1 millimeter)
Accuracy: + / - 3%
Transmission: 100 feet (30 meters) in an open area
Transmission Rate: Every 30 seconds during rainfall, otherwise sent every 2?? minutes. Transmissions from remote temperature sensor sent every 2?? minutes.
Clock: Quartz precisions +/- 30 seconds per month
Battery Life: 1 year (alkaline batteries recommended)
*Important: To extend outdoor temperature range to
** Using the sensor probe cable will allow you to keep the unit in a warmer place without using Lithium batteries.
A maximum of 3 remote sensor units can be registered. One remote sensor is included. To purchase additional Remote Sensors (Taylor model 1457), please check availability with your local Taylor?? retailer, or call
One Year Warranty
This product is warranted against defects in materials or workmanship for one (1) year from the date of original purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and/or repair.
Should this product require service (or replacement at our option) while under warranty, do not return to retailer. Please pack the item carefully and return it prepaid, along with a store receipt showing date of purchase and a note explaining reason for return to:
Taylor Precision Products
2220 Entrada Del Sol
Las Cruces, New Mexico 88001
www.taylorusa.com
There are no express warranties except as listed above. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Made to our exact specifications in China.
??2006 Taylor Precision Products and its affiliated companies, all rights reserved. Taylor?? and Leading the Way in Accuracy?? are registered trademarks of Taylor Precision Products and its affiliated companies. All rights reserved.
CP2751 - 09.06R1
Thank you for purchasing the Taylor?? Digital Wireless Rain Gauge and Thermometer. This
Description of Parts
Description of Parts (Continued)
18 13
16
Main Features & How to Access Functions (continued)
Line 5 Indoor Temperature Display. Shows the temperature where the indoor receiver is located.
Main Features & How to Access Functions (continued)
15. ???TM??? Button
Press to send a registration signal to the receiver unit.
16. Battery Compartment
The sensor unit requires 2 AA alkaline batteries (not included).
See Battery Installation section of this manual.
17. Table Stand
Pull the bottom of stand out from the housing for stable placement of the unit on a flat surface.
18. Wall Mount
Detachable holder with a key hole slot to secure the sensor to a wall.
19. Cable Jack
Plug the sensor probe of the
Rainfall Transmitter Unit
Battery Installation (continued)
Receiver:
1. Lift off the battery compartment cover
located on the back of the unit.
2. Insert 2 AA alkaline batteries as indicated by the polarity symbols marked inside the battery compartment.
3. After installing the batteries, the display will show flashing dashes. Once the transmitter's batteries are installed and the unit successfully transmits a signal and is
temperature.
4. Replace the battery compartment cover.
Remote Temperature Sensor:
Battery Installation (continued)
Rain Gauge Transmitter:
Setting Up The Rain Gauge Transmitter
Figure: A
Unscrew the 2 screws then lift the top casing off
Low Battery Indicator and Battery Replacement (cont.)
4.After replacing batteries in the transmitter, press and hold the "+" button on the receiver for 3 seconds to cancel the previous signal registration and register a new signal between the units. The rainfall displays on the LCD will blink
5.After replacing batteries in the remote sensor, cancel the signal registration of the corresponding channel of the receiver unit by 1) pushing the channel button to select the respective channel; 2) holding the "CH" button for 3 seconds to clear the registration. Re- register the remote sensors by pressing "TM" key on the remote sensors. The updated temperature will appear on the receiver.
6.If the receiver's batteries are replaced, the batteries of both the remote sensor and transmitter must be reinstalled as well. Follow transmission signal registration instructions in steps 4 and 5.
Line 3
Line 5
5 6 7
17
Main Features & How to Access Functions
Indoor Receiver Unit
1. LCD Readout
Line 1 Daily Rainfall Display. Reports today's total rainfall.
Line 2 Weekly/Monthly/Total Accumulated Rainfall Display. Shows either the weekly, monthly, or total accumulated rainfall. The
The back of the receiver has a recessed key hole to secure the unit
Battery Compartment
The transmitter requires 2 AA alkaline batteries (not included). See Battery Installation section of this manual.
Rain Gauge Net
A protective stainless steel net is placed
on top of the rain gauge to guard against rocks, leaves, and other debris collecting in the rain gauge. The net may be removed for cleaning by pulling up on the ring at the side of the net.
Rain Gauge
Net
Low Battery Indicator and Battery Replacement
Use 2 'AA' batteries
Important: When the temperature falls below freezing, the batteries of the remote sensor and rainfall transmitter units may freeze, lowering their voltage supply and effective range. Use Lithium batteries to insure operation below 10??F
How to Set and Use Clock & Calendar Functions
10
8
9
???WEEK??? icon appears above the rainfall digits when the receiver is in week mode. The ???MONTH??? icon appears during monthly mode. If no icon is visible, the total accumulated rainfall is displayed. Press ??? - ??? to toggle between the different displays.
Line 3 Clock and Calendar display. Shows the current time, date, and day of the week.
Line 4 Remote Temperature Display. Shows the temperature at the remote sensor location. Up to 3 remote sensors may be used (one is included, other Model 1457 sensors may be purchased separately). Press the ???CH??? button to toggle between sensor readings.
to a wall.
Remote Temperature Sensor Unit
11. LCD Readout
Shows the temperature at the sensor's location.
12. LED Indicator
Flashes when the remote sensor transmits a reading.
13. Channel Switch
Slide to designate the remote sensor channel 1, 2, or 3.
14. ?????F/??C??? Button
Press to select ??F or ??C temperature scale.
Important:
The rain gauge should not be left outdoors in
temperatures at or below
weather. If the temperature drops to this level or it begins to snow, remove the rain gauge to an indoor area.
Battery Installation
For the initial installation, insert the batteries into the receiver unit first, then the transmitter, and finally the remote sensor. Place all three units next to each other during battery installation for best signal initialization.
desired temperature scale.
6.Press the ???TM??? button to send a 
transmission signal to the receiver. The red 
LED indicator light will flash when a signal 
is transmitted. Remote unit temperature 
updates will then be transmitted at 2 minute 
30 second intervals. Note: If dashes are still
displayed on the receiver unit, press the ???TM???
button to send another transmission. 
7.Replace the battery compartment cover, replace
and tighten screws, and reattach the bracket stand. 
Unscrew the 4 screws from the battery compartment cover