I N S T A L L A T I O N I N S T R U C T I O N S

Universal Pitch-Adjustable Wall Mount

For Flat Panel Display PLP-91/D

Once the Universal Flat Panel Display Wall Mount Bracket is attached to your display, simply attach the mount securely on a wall, lock the display in place using the convenient Q-latch, and attach your audio/video cables.

The PLP-91/D is virtually invisible when your display is mounted.

BEFORE YOU BEGIN

???Caution: To prevent damage to the PLP-91/D, which could affect or void the Factory warranty, and to the equipment that will be attached to it, thoroughly study all instructions and illustrations before you begin the installation. Pay par- ticular attention to the ???Important Warnings and Precautions??? on Page 1.

???The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the mount must be capable of supporting five times the total weight of the equipment.

???The maximum weight to be installed on the Universal Pitch-Adjustable Wall Mount is 125 pounds (56.7 Kg).

Sony Electronics Inc. 8805-000087

1 Sony Drive

Park Ridge, NJ 07656 201-930-1000 www.sony.com/displaysystems

IMPORTANT WARNINGS AND PRECAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre- sponding instructions.

??? WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can support a weight factor five times the total weight of the equipment. If not, reinforce the structure before installing the mount.

???WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

???WARNING:The installer is responsible for verifying that the wall to which the mount is anchored will safely support

the combined load of all attached components or other equipment.

???WARNING:Watch for pinch points. Do not put your fingers between movable parts.

???WARNING:Make sure the mount and brackets are correctly oriented.

???WARNING:Make sure the latching flag securing the display is completely engaged at all times except when removing

or installing the display. The latching flag must be all completely engaged when installing/removing cables.

???CAUTION: Check the unit for shipping damage before you begin the installation.

???CAUTION: Use only the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

TOOLS REQUIRED FOR INSTALLATION

???Phillips screwdrivers, No. 1 and No. 2 TIP

???Drill and bit set

???Wrench set

NOTE: Other tools may be required depending on the method of installation.

1

10 1/2"

2"

8"

5/16"

DIMENSIONAL DRAWING

2

INSTALL MOUNT

Install the mount as follows:

1.Determine the exact mounting location prior to installation and draw a level line to indicate the desired height for the top of the mounting plate.

WARNING: Improper installation can result in serious per- sonal injury! Make sure that the structural framework can support a weight factor five times the total weight of the equipment. If not, reinforce the structure before installing the mount.

2.With the mount correctly oriented and level, secure the mount to the wall (see Figure 1) using four fasteners (not included). Fasteners must be driven into the supporting wall studs or other supporting framework.

3.Check mount to ensure it is level and adjust to level if necessary.

INSTALL DISPLAY BRACKETS

Install display bracket(s) according to the instructions provided. The bracket(s) is/are designed for your specific model.

MOUNT THE DISPLAY

Mount the display as follows:

1.Make sure no power is supplied to the display and the flags are in the lowered (open) position before attempting to mount the display.

Mounting

Holes

Mounting

Holes

Figure 1. Mounting Hole Locations

Security Lock May Be

Installed

Figure 2. Optional Security

2.Using two people, slide the display down over the mount. Make sure all four Q-buttons of the display engage all four slots in the mount.

3.With the Q-buttons of the display fully engaged in the slots of the mount, secure the display on the mount by raising the flags all the way to their locked position. If the flags do not fully engage, remove the display and make sure the brackets are correctly installed.

NOTE: A security lock may be installed through the hole in the locking flag for additional security (see Figure 2).

NOTE: If display does not remain at desired tilt setting, tighten the nut and bolt on tilt arms on each side (see Figure 3).

WARNING: Make sure the flag securing the display is com- pletely lowered at all times except when removing or installing the display. The flag must be all the way down when installing/removing cables.

Loosen or tighten this nut

to adjust tilt tension

Loosen or tighten this bolt

to adjust tilt tension

Figure 3. Tilt Tension Adjustment

3

Installation InstructionsPitch-Adjustable Mount PLP91/D

PARTS

Table 1: Parts

4

I N S T A L L A T I O N I N S T R U C T I O N S

PSB-91/D

PLASMA DISPLAY MOUNTING BRACKET

Prior to assembly, unpack carton completely and verify contents.

If you are missing any of the following components, please contact Customer Service at 1-800/582-6480

BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY

CAUTION!

WARNING!

PLASMA DISPLAYS ARE EXTREMELY FRAGILE.

ALL COMPONENTS MUST BE SECURELY FASTENED TO A

STRUCTURAL MEMBER CAPABLE OF SUPPORTING 4

TIMES THE COMBINED WEIGHT OF ALL COMPONENTS

PLUS THE EQUIPMENT BEING MOUNTED. IF IT CANNOT

SUPPORT THIS WEIGHT, THE STRUCTURE MUST BE

REINFORCED.

THE MAXIMUM WEIGHT TO BE INSTALLED ON THE MOUNT IS 125 POUNDS (56.7 KG).

1.Using a 10-24 button head cap screw inserted from back side of bracket, secure mounting button, with chamfered hole of mounting button (larger surface) facing bracket, to bracket (four places) (see Figure 2 & Figure 3).

1 Sony Drive

Park Ridge, NJ 07656 201-930-1000 www.sony.com/displaysystems

2.Place Nylon spacers over mounting holes on back of screen.

3.Attach mounting brackets to the display using the M5 screws for 32??? screen or M6 for 42??? and 50??? screens (see Figure 4 & Figure 5).

4.With the aid of another person, lift your display up to the mount, aligning buttons of mounting brackets with slots in the mount.

5.Lower safety catch on the mount to secure your display, making sure latch is completely engaged.

Figure 4

Figure 5